RCD FR1ER-R100-HT Failsafe fuse resistors 1/2 watt to 50 watt Datasheet

FAILSAFE FUSE RESISTORS
1/2 WATT to 50 WATT
FR SERIES
RESISTORSCAPACITORSCOILSDELAY LINES
RCD
Term.W is
RoHS
compliant
& 260°C
compatible
RoHS
Precision Grade Fuse Resistors!
RCD’s FR Series was designed to obtain the best from two devices. It
combines the performance of a precision grade resistor with precisely
controlled fusing characteristics. Typical applications include protection
for zener diodes and other semiconductor components, emitter
resistors for current sharing transistors, Squib circuits, and/or other
circuits that require precision fusing chracteristics unobtainable with
traditional fuses.
Precision performance, flameproof design per UL94V-0
Fusing-to-Operating current ratios as low as 3:1!
Fusing times available from 1 millisecond to 30 seconds
Available on exclusive SWIFTTM delivery program
Custom design available for increased surge capability
(specify Option P)
Also available: Hi-Rel screening, burn-in, custom marking, etc.
|←
←
L
|←
← 1.0” [25.4] min.→|
→
→|
↓
↓
Please note that due to the inherent compromise involved between
resistive vs. fusing performance it is recommended that prior consultation be made with RCD’s engineering department to obtain the optimum
design. Parts intended for high-reliability applications are available
with burn-in (opt. ER) and/or military screening.
d
↑
↑
D
SPECIFICATIONS
RCD Wattage
Type* @25°C(W25)
FR1/2
0.5
FR1
1.0
FR2
2.0
FR3
3.5
FR5
5.5
PERFORMANCE CHARACTERISTICS
Resistance
Range
.06Ω to 500Ω
0.1Ω to 1.5K
0.1Ω to 2K
0.1Ω to 3K
0.1Ω to 5K
L ±.04 [1] D±.02 [.5]
.29 [7.4]
.60 [15.2]
.69 [17.5]
.58 [14.7]
.984 [25]
.125
.130
.170
.230
.323
[3.2]
[3.3]
[4.3]
[5.8]
[8.2]
d typ
.020
.020
.032
.032
.032
[.5]
[.5]
[.8]
[.8]
[.8]
Tolerance
Temperature
Coefficient (typ)
Dielectric Strength
Insulation Resistance
Derating
5% standard, 0.1-10% available
±100ppm 0.1-.9Ω, ±50ppm 1Ω &up,
available to ±10ppm
750 VAC
1,000 megohms min. (dry)
Derate linearly from full rated power @
25°C to zero power @175°C (.67%/°C)
* Other sizes available up to 50 Watt on a custom basis.
FUSING CHARACTERISTICS: Standard FR resistors are designed to fuse within 10 seconds as follows:
FR1/2 to FR2 ≥1Ω = 20 x W25 (20 times the 25°C wattage rating), <1Ω = 40 x W25. FR3 & FR5 ≥5Ω = 25 x W25 , <5Ω = 50 x W25.
Faster fusing is available. Max. fault condition not to exceed 300x W25. Following chart depicts custom design capabilities.
Fusing
Current
(Amperes)
0.15
0.25
0.5
1.0
1.5
2.0
3.0
5.0
10
15
20
Minimum Resistance Value to Fuse in 1 Sec. or Less
Minimum Resistance Value to Fuse in 5 Sec. or Less
FR1/2
FR 1
FR 2
FR 3
FR 5
FR1/2
FR 1
FR 2
FR 3
FR 5
360Ω
120Ω
30Ω
7.5Ω
3.3Ω
2.0Ω
1.0Ω
0.5Ω
0.25Ω
0.15Ω
0.1Ω
720Ω
240Ω
60Ω
15Ω
7Ω
4Ω
2Ω
1Ω
.5Ω
.3Ω
.2Ω
1.44K
480Ω
120Ω
30Ω
13Ω
8Ω
4Ω
2Ω
1Ω
.6Ω
.4Ω
2.88K
960Ω
240Ω
60Ω
26Ω
16Ω
8Ω
4Ω
2Ω
1.2Ω
.8Ω
5.76K
1920Ω
480Ω
120Ω
53Ω
32Ω
16Ω
8Ω
4Ω
2.4Ω
1.6Ω
180Ω
60Ω
15Ω
3.8Ω
1.7Ω
1.0Ω
0.5Ω
.25Ω
.13Ω
.08Ω
.06Ω
360Ω
120Ω
30Ω
7.5Ω
3.3Ω
2Ω
1Ω
.5Ω
.25Ω
.15Ω
.10Ω
720Ω
240Ω
60Ω
15Ω
7Ω
4Ω
2Ω
1Ω
.5Ω
.3Ω
.2Ω
1.44K
480Ω
120Ω
30Ω
13Ω
8Ω
4Ω
2Ω
1Ω
.6Ω
.4Ω
2.88K
960Ω
240Ω
60Ω
26Ω
16Ω
8Ω
4Ω
2Ω
1.2Ω
.8Ω
APPLICATION & DESIGN NOTES:
Fusing current should be ≥ 4 times the continuous current for best performance.
Resistors reach elevated temperatures prior to opening- elevate body above the PCB.
Exercise care when testing fuse resistors.
RCD can custom manufacture fuse resistors from 1/8W to 50W per customer req’t.
Design objectives are achieved by element material (wirewound or film), insulation
(silicone, ceramic, epoxy), and process (alloy & resistor geometry).
5. Thermal fuses are also available and are designed to “blow” when the resistor body or
the ambient temperature reaches preset temperature (110°C to 240°C).
6. Custom surge-tolerant fuses are designed not to “blow” due to short term voltage
transients, lightning surges, or capacitor discharges, but will fuse under longer term
overloads. Consult factory for details.
7. Please include the following information when customized design is required:
Continuous wattage or current; ambient temperature; fusing wattage or current;
minimum and maximum “blow” times; resistance value & tolerance; max. size; voltage
level, AC or DC, wave form, & frequency; and a general description of the application.
Include info as to any pulse or overload conditions that the resistor must withstand.
1.
2.
3.
4.
P/N DESIGNATION:
FR1
- 101 - J B
W
RCD Type
Options: P, ER (additional options to
be assigned by RCD, leave blank if std)
Resis. Code: ≤1%: 3 signif. figures & multiplier,
e.g. R100= 0.1Ω, 1R00= 1Ω,1000= 100Ω, 1001= 1KΩ.
Resis. Code 2% - 10%: 2 signif. figures & multiplier,
e.g. R10= 0.1Ω, 1R0= 1Ω,100= 10Ω, 102= 1KΩ.
Tolerance: K=10%, J=5% (std), H=3%, G=2%,
F=1%, D=0.5%, C=0.25%, B=0.1%
Packaging: B= Bulk, T= T&R
Optional Temp. Coef: (leave blank if standard)
10 = 10ppm, 25 = 25ppm, 50 = 50ppm, 101=100pm
Termination: W= Lead-free, Q= Tin/Lead
(leave blank if either is acceptable)
RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: 603-669-0054 Fax: 603-669-5455 Email:[email protected]
FA062A
Sale of this product is in accordance with GF-061. Specifications subject to change without notice.
80
Similar pages