DATASHEET HI3026 FN4109 Rev.3.00 August 1997 8-Bit, 120 MSPS, Flash A/D Converter Features Description • Differential Linearity Error . . . . . . . . . . . . . . . . 0.5 LSB • RGB Graphics Processing (LCD, PDP) The HI3026 is an 8-bit, high-speed, flash analog-to-digital converter optimized for high speed, low power, and ease of use. With a 120 MSPS encode rate capability and full-power analog bandwidth of 150MHz, this component is ideal for applications requiring the highest possible dynamic performance. To minimize system cost and power dissipation, only a +5V power supply is required. The HI3026’s clock input interfaces directly to TTL, ECL, or PECL logic and will operate with singleended inputs. The user may select 16-bit demultiplexed output or 8-bit single channel digital outputs. The demultiplexed mode interleaves the data through two 8-bit channels at 1/2 the clock rate. Operation in demultiplexed mode reduces the speed and cost of external digital interfaces, while allowing the A/D converter to be clocked to the full 120 MSPS conversion rate. Fabricated with an advanced Bipolar process, the HI3026 is provided in a space-saving 48-lead MQFP surface mount plastic package and is specified over the -20°C to 75°C temperature range. For a faster clock rate, please refer to the HI3026A (140 MSPS). • Digital Oscilloscopes Ordering Information • Integral Linearity Error . . . . . . . . . . . . . . . . . . . 0.5 LSB • Integral Linearity Compensation Circuit • Low Input Capacitance. . . . . . . . . . . . . . . . . . . . . . 21pF • Wide Analog Input Bandwidth. . . . . . . . . . . . . . 150MHz • Low Power Consumption. . . . . . . . . . . . . . . . . . 760mW • Internal 1/2 Frequency Divider Circuit (w/Reset Function) • CLK/2 Clock Output • Compatible with ECL, PECL and TTL Digital Input Levels • 1:2 Demultiplexed Output Pin • Surface Mounting Package • Direct Replacement for Sony CXA3026Q Applications • Digital Communications (QPSK, QAM) PART NUMBER • Magnetic Recording (PRML) TEMP. RANGE (°C) HI3026JCQ -20 to 75 HI3026EVAL 25 PACKAGE PKG. NO. 48 Ld MQFP Q48.12x12-S Evaluation Board Pinout P1D4 P1D7 P1D6 P1D5 DVCC2 DGND2 CLKOUT RESETN/T DVEE3 1 48 47 46 45 44 43 42 41 40 39 38 37 36 VRB AGND VRM1 2 3 35 34 P1D2 4 5 33 32 31 P1D0 DGND2 DVCC2 30 29 DVCC1 P1D3 P1D1 DGND1 P2D7 P2D6 P2D5 P2D4 P2D3 P2D2 P2D0 P2D1 NC 26 11 25 12 13 14 15 16 17 18 19 20 21 22 23 24 CLK/E DGND3 28 27 DVCC2 DGND2 VRT 8 9 10 NC VRM3 AGND CLK/T NC AVCC 6 7 CLKN/E AVCC VIN VRM2 FN4109 Rev.3.00 August 1997 SELECT INV RESETN/E RESET/E HI3026 (MQFP) TOP VIEW Page 1 of 17 HI3026 Block Diagram AVCC 5 8 INV DVCC1 44 30 DVCC2 DGND3 19 31 42 12 VRT 11 R1 R/2 R (MSB) 40 P1D7 1 R 39 P1D6 2 6 BITS 38 P1D5 9 8 BITS R 64 R 37 P1D4 TTLOUT 63 VRM3 LATCHA R 36 P1D3 35 P1D2 65 6 BITS 126 7 VIN 6 127 R 128 ENCODER R VRM2 R 129 34 P1D1 6-BIT LATCH AND ENCODER R 33 P1D0 (LSB) 8 BITS (MSB) 28 P2D7 6 BITS R 27 P2D6 191 4 R 26 P2D5 192 193 R TTLOUT R LATCHB VRM1 25 P2D4 24 P2D3 6 BITS 23 P2D2 254 R 22 P2D1 255 R/2 VRB 2 CLK/T 15 CLK/E 13 CLKN/E 14 21 P1D0 (LSB) R/2 DELAY 17 46 RESETN/E 48 RESET/E 47 Q Q 3 10 AGND FN4109 Rev.3.00 August 1997 NC 18 D RESETN/T 16 43 CLKOUT SELECT 45 29 SELECT DGND1 20 32 41 DGND2 1 DVEE3 Page 2 of 17 HI3026 Absolute Maximum Ratings TA = 25oC Thermal Information Supply Voltage (AVCC , DVCC1, DVCC2) . . . . . . . . . . -0.5V to 7.0V (DGND3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7.0V (DVEE3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7.0V to 0.5V (DGND3 - DVEE3). . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7.0V Analog Input Voltage (VIN) . . . . . . . . . . . . . . . . .VRT - 2.7V to AVCC Reference Input Voltage (VRT). . . . . . . . . . . . . . . . . . .2.7V to AVCC (VRB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIN - 2.7V to AVCC (|VRT - VRB|). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5V Digital Input Voltage ECL (***/E (Note 2)) . . . . . . . . . . . . . . . . . . . . . . . . DVEE3 to 0.5V PECL (***/E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to DGND3 TTL (***/T, INV). . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to DVCC1 Other (SELECT) . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to DVCC1 VID (|***/E - ***N/E| (Note 3)) . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V Thermal Resistance (Typical, Note 1) JA (oC/W) MQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Maximum Junction Temperature. . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . . 300oC (Lead Tips Only) Recommended Operating Conditions WITH A SINGLE POWER SUPPLY MIN TYP MAX Supply Voltage DVCC1 , DVCC2 , AVCC . . . . . . . . . . . . . . . +4.75 +5.0 +5.25V DGND1, DGND2, AGND . . . . . . . . . . . . . -0.05 0 +0.05V DGND3 . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.75 +5.0 +5.25V DVEE3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.05 0 +0.05V Analog Input Voltage (VIN) . . . . . . . . . . . . . . VRB VRT Reference Input Voltage VRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.9 +4.1V VRB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 +2.6V |VRT - VRB| . . . . . . . . . . . . . . . . . . . . . . . . 1.5 2.1V Digital Input Voltage PECL (***/E) VIH . . . . . . . . . . . . . . . DGND3 - 1.05 DGND3 - 1.4V PECL (***/E) VIL . . . . . . . . . . . . . . . DGND3 - 3.2 DGND3 - 1.4V TTL (***/T, INV) VIH . . . . . . . . . . . . . . . . . 2.0V TTL (***/T, INV) VIL . . . . . . . . . . . . . . . . . . 0.8V Other (SELECT) VIH . . . . . . . . . . . . . . . . . DVCC1 Other (SELECT) VIL . . . . . . . . . . . . . . . . . DGND1 VID (Note 3) (|***/E- ***N/E|). . . . . . . . . . . 0.4 0.8 Max Conversion Rate (fC , Straight Mode) . . . 100 MSPS Max Conversion Rate (fC , DMUX Mode) . . . . 120 MSPS Ambient Temperature (TA) . . . . . . . . . . . . . . . . . . . . . -20oC to 75oC WITH DUAL POWER SUPPLIES MIN TYP MAX Supply Voltage DVCC1 , DVCC2 , AVCC . . . . . . . . . . . . . . +4.75 +5.0 +5.25V DGND1, DGND2, AGND . . . . . . . . . . . . . -0.05 0 +0.05V DGND3 . . . . . . . . . . . . . . . . . . . . . . . . . . -0.05 0 +0.05V DVEE3 . . . . . . . . . . . . . . . . . . . . . . . . . . . -5.5 -5.0 -4.75V Analog Input Voltage (VIN) . . . . . . . . . . . . . VRB VRT Reference Input Voltage VRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.9 +4.1V VRB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 +2.6V |VRT - VRB| . . . . . . . . . . . . . . . . . . . . . . . 1.5 2.1V Digital Input Voltage ECL (***/E) VIH . . . . . . . . . . . . . . . . DGND3 - 1.05 DGND3 - 0.5V ECL (***/E) VIL . . . . . . . . . . . . . . . . DGND3 - 3.2 DGND3 - 1.4V TTL (***/T, INV) VIH . . . . . . . . . . . . . . . . . 2.0V TTL (***/T, INV) VIL . . . . . . . . . . . . . . . . . 0.8V Other (SELECT) VIH . . . . . . . . . . . . . . . . DVCC1 Other (SELECT) VIL . . . . . . . . . . . . . . . . DGND1 VID (Note 3) (|***/E- ***N/E|) . . . . . . . . . . 0.4 0.8 Max Conversion Rate (fC , Straight Mode) . . . 100 MSPS Max Conversion Rate (fC , DMUX Mode). . . . 120 MSPS Ambient Temperature (TA) . . . . . . . . . . . . . . . . . . . . .-20oC to 75oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. JA is measured with the component mounted on an evaluation PC board in free air. 2. ***/E and ***T indicate CLK/E and CLK/T, etc., for the pin name. 3. VID : Input Voltage Differential. Electrical Specifications PARAMETER DVCC1 , 2 , AVCC , DGND3 = +5V, DGND1, 2, AGND, DVEE3 = 0V, VRT = 4V, VRB = 2V, TA = 25oC TEST CONDITIONS MIN TYP MAX UNITS - 8 - Bits - - 0.5 LSB - - 0.5 LSB - 21 - pF Analog Input Resistance, RIN 4 - 50 k Analog Input Current, IIN 0 - 500 A Resolution DC CHARACTERISTICS Integral Linearity Error, EIL VIN = 2VP-P , fC = 5 MSPS Differential Linearity Error, EDL ANALOG INPUT Analog Input Capacitance, CIN FN4109 Rev.3.00 August 1997 VIN = +3.0V +0.07VRMS Page 3 of 17 HI3026 Electrical Specifications DVCC1 , 2 , AVCC , DGND3 = +5V, DGND1, 2, AGND, DVEE3 = 0V, VRT = 4V, VRB = 2V, TA = 25oC (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS REFERENCE INPUT Reference Resistance (Note 4), RREF 75 115 155 Reference Current (Note 5), IREF 9.7 17.4 28 mA Offset Voltage VRT Side, EOT 2 - 15 mV Offset Voltage VRB Side, EOB 2 - 10 mV Digital Input Voltage: High, VIH DGND3 - 1.05 - DGND3 - 0.5 V Digital Input Voltage: Low, VIL DGND3 - 3.2 - DGND3 -1.4 V - DGND3 - 1.2 - V DIGITAL INPUT (ECL, PECL) Threshold Voltage, VTH Digital Input Current: High, IIH VIH = DGND3 - 0.8V -50 - +50 A Digital Input Current: Low, IIL VIL = DGND3 - 1.6V -75 - 0 A - - 5 pF Digital Input Voltage: High, VIH 2.0 - - V Digital Input Voltage: Low, VIL - - 0.8 V Threshold Voltage, VTH - 1.5 - V - 0 A Digital Input Capacitance DIGITAL INPUT (TTL) Digital Input Current: High, IIH VIH = 3.5V -50 Digital Input Current: Low, IIL VIL = 0.2V -500 - 0 A - - 5 pF Digital Input Capacitance DIGITAL OUTPUT (TTL) Digital Output Voltage: High, VOH IOH = -2mA 2.4 - - V Digital Output Voltage: Low, VOL IOL = 1mA - - 0.5 V 120 - - MSPS - 10 - ps SWITCHING CHARACTERISTICS Maximum Conversion Rate, fC DMUX Mode Aperture Jitter, tAJ 3 4.5 6 ns Clock High Pulse Width, tPW1 CLK 3.2 - - ns Clock Low Pulse Width, tPW0 CLK 3.2 - - ns Reset Pulse Width, tPWR (Note 6) RESETN tx2 - - ns Sampling Delay, tDS RESET Signal Setup Time, tRS RESETN-CLK 3.5 - - ns RESET Signal Hold Time, tRH RESETN-CLK 0 - - ns CLKOUT Output Delay, tDCLK (CL = 5pF) 3.5 7 9 ns Data Output Delay (Note 6), tDO1 tDO2 DEMUX Mode (CL = 5pF) t t+1 t+2 ns (CL = 5pF) 4.5 8 10 ns Output Rise Time, tr 0.8 to 2.0V (CL = 5pF) - 2 - ns Output Fall Time, tf 0.8 to 2.0V (CL = 5pF) - 2 - ns DYNAMIC CHARACTERISTICS Input Bandwidth VIN = 2VP-P , -3dB 150 - - MHz S/N Ratio fC = 120 MSPS, fIN = 1kHz Full Scale, DMUX Mode - 46 - dB fC = 120 MSPS, fIN = 29.999MHz Full Scale, DMUX Mode - 40 - dB FN4109 Rev.3.00 August 1997 Page 4 of 17 HI3026 Electrical Specifications DVCC1 , 2 , AVCC , DGND3 = +5V, DGND1, 2, AGND, DVEE3 = 0V, VRT = 4V, VRB = 2V, TA = 25oC (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS TPS fC = 120 MSPS, fIN = 1kHz Full Scale, DMUX Mode, Error > 16 LSB - - 10-12 fC = 120 MSPS, fIN = 29.999MHz Full Scale, DMUX Mode, Error > 16 LSB - - 10-9 TPS fC = 100 MSPS, fIN = 24.999MHz Full Scale, Straight Mode, Error > 16 LSB - - 10-9 TPS Supply Current, ICC 125 145 185 mA Supply Current, IEE 0.4 0.6 0.8 mA Power Consumption (Note 8), PD 660 760 960 mW Error Rate (Note 7) POWER SUPPLY NOTES: 4. RREF: Resistance value between VRT and VRB . V RT – V RB 5. I REF = ---------------------------R REF . 1 6. T = ----- . fC 7. The unit of measure TPS: Times Per Sample. V RT – V RB 2 -. 8. P D = I CC + I EE V CC + -----------------------------------V REF Timing Diagrams N-1 VIN N+2 N+3 tDS N t N+1 CLK tPW1 tD02 tPW0 P1D0 TO D7 N-2 P2D0 TO D7 N-3 2V N N+2 N-1 N-1 0.8V 2V 0.8V tD01 tDCLK t + 1ns CLK OUT 2V 2V 0.8V 0.8V RESET PULSE tPWR FIGURE 1. DEMUX MODE TIMING CHART (SELECT = VCC) FN4109 Rev.3.00 August 1997 Page 5 of 17 HI3026 Timing Diagrams N+2 N-1 VIN N+3 N+1 tDS N t CLK tPW1 tPW0 P1D0 TO D7 N-4 2.0V 0.8V N-3 N-2 N-1 N P2D0 TO D7 N-5 2.0V 0.8V N-4 N-3 N-2 N-1 tD02 8ns 2.0V CLK OUT (CLK IS INVERTED AND OUTPUT) 0.8V tDCLK RESET PULSE FIGURE 2. STRAIGHT MODE TIMING CHART (SELECT = GND) DGND3 VIH (MAX) VIL VTH (DGND3 - 1.2V) VID VIH VIL (MIN) FIGURE 3. ECL AND PECL SWITCHING LEVEL Pin Descriptions I/O TYPICAL VOLTAGE LEVEL PIN NO SYMBOL EQUIVALENT CIRCUIT DESCRIPTION 3, 10 AGND GND Analog Ground. Separated from the digital ground. 5, 8 AVCC +5V (Typ) Analog Power Supply. Separated from the digital power supply. 20, 29 32, 41 DGND1 DGND2 GND Digital Ground. 19, 30 31, 42 DVCC1 DVCC2 +5V (Typ) Digital Power Supply. 12 DGND3 +5V (Typ) (With a Single Power Supply) Digital Power Supply. Ground for ECL input. -5V for PECL and TTL input. GND (With Dual Power Supplies) FN4109 Rev.3.00 August 1997 Page 6 of 17 HI3026 Pin Descriptions (Continued) PIN NO SYMBOL 1 DVEE3 I/O TYPICAL VOLTAGE LEVEL EQUIVALENT CIRCUIT GND (With a Single Power Supply) DESCRIPTION Digital Power Supply. Ground for ECL input. -5V for PECL and TTL input. +5V (Typ) (With Dual Power Supplies) 16, 17, 18 NC No Connect pin. Not connected with the internal circuits. 13 CLK/E I 14 CLK/NE I ECL/PECL Clock Input. DGND3 R R 13 48 14 47 I 47 RESET/E I Reset Input. When the input is set to low level, the built-in CLK frequency divider circuit can be reset. 1.2V R RESETN/E R 48 DVEE3 15 CLK/T I 46 RESETN/T I CLK/E Complementary Input. When left open, this pin goes to the threshold potential. Only CLK/E can be used for operation, but complementary input is recommended to attain fast and stable operation. TTL Clock input. DVCC1 R/2 15 46 RESETN/E Complementary Input. When left open, this pin goes to the threshold voltage. Only RESETN/E can be used for operation. R Reset Input. When left open, this input goes to high level. When the input is set to low level, the built-in CLK frequency divider circuit can be reset. 1.5V DGND1 DVEE3 44 INV I TTL DVCC1 Data Output Polarity Inversion Input. When left open, this input goes to high level. (See Table 1; I/O Correspondence Table). 44 DGND1 DVEE3 45 SELECT VCC or Ground Data Output Mode Selection. (See Table 2; Operating Mode Table). DVCC1 45 DGND1 DVEE3 FN4109 Rev.3.00 August 1997 Page 7 of 17 HI3026 Pin Descriptions (Continued) PIN NO SYMBOL I/O 11 VRT I TYPICAL VOLTAGE LEVEL EQUIVALENT CIRCUIT 4.0V (Typ) 11 9 7 4 2 VRM3 VRB + 2 --- (VRT - VRB) 4 VRM1 VRB VRB + 1 --- (VRT - VRB) 4 I 2.0V (Typ) Top Reference Voltage. Bypass to AGND with a 1F tantal capacitor and a 0.1F chip capacitor. R1 R/2 VRB + 3 --- (VRT - VRB) 4 VRM2 DESCRIPTION Reference Voltage Mid Point. Bypass to AGND with a 0.1F chip capacitor. R COMPARATOR 1 R COMPARATOR 63 9 R 7 R Reference Voltage Mid Point. Bypass to AGND with a 0.1F chip capacitor. COMPARATOR 64 COMPARATOR 127 Reference Voltage Mid Point. Bypass to AGND with a 0.1F chip capacitor. COMPARATOR 128 COMPARATOR 191 4 R COMPARATOR 192 Bottom Reference Voltage. Bypass to AGND with a 1F tantal capacitor and a 0.1F chip capacitor. R COMPARATOR 255 R/2 2 R2 6 VIN I VRT to VRB Analog Input. COMPARATOR AVCC AVCC VREF 6 AGND DVEE3 33 to 40 P1D0 to P1D7 O 21 to 28 P2D0 to P2D7 O CLKOUT O 43 TTL Port 1 Side Data Output. Port 2 Side Data Output. DVCC1 DVCC2 21 TO 28 Clock Output. (See Table 2; Operating Mode Table). 100K 33 TO 40 DGND1 FN4109 Rev.3.00 August 1997 43 DGND2 DVEE3 Page 8 of 17 HI3026 TABLE 1. A/D CODE TABLE INV 1 0 VIN STEP VRT 255 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 254 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 D7 D0 • • • 128 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 127 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 • • • • • • • • • VRB D0 • • • • • • VRM2 D7 1 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Notes on Operation • The HI3026 is a high-speed A/D converter which is capable of TTL, ECL and PECL level clock input. Characteristic impedance should be properly matched to ensure optimum performance during high-speed operation. • The power supply and grounding have a profound influence on converter performance. The power supply and grounding method are particularly important during high-speed operation. General points for caution are as follows: - The ground pattern should be as large as possible. It is recommended to make the power supply and ground patterns wider at an inner layer using a multi-layer board. - To prevent interference between AGND and DGND and between AVCC and DVCC , make sure the respective patterns are separated. To prevent a DC offset in the power supply pattern, connect the AVCC and DVCC lines at one point each, via a ferrite-bead filter. Shorting the AGND and DGND patterns in one place immediately under the A/D converter improves A/D converter performance. - Ground the power supply pins (AVCC , DVCC1 , DVCC2 , DVEE3) as close to each pin as possible with a 0.1F or larger ceramic chip capacitor. (Connect the AVCC pin to the AGND pattern and the DVCC1 , DVCC2 , DVEE3 pins to the DGND pattern). - The digital output wiring should be as short as possible. If the digital output wiring is long, the wiring capacitance will increase, deteriorating the output slew rate and resulting in reflection to the output waveform since the original output slew rate is quite fast. • The analog input pin VIN has an input capacitance of approximately 21pF. To drive the A/D converter with proper frequency response, it is necessary to prevent performance deterioration due to parasitic capacitance or parasitic inductance by using a large capacity drive circuit; keeping wiring as short as possible, and using chip parts for resistors and capacitors, etc. • The VRT and VRB pins must have adequate bypass to protect them from high-frequency noise. Bypass them to AGND with approximately 1F tantal capacitor and, 0.1F capacitor. At this time, approximately DGND3 - 1.2V voltage is generated. However, this is not recommended for use as threshold voltage VBB as it is too weak. When the digital input level is ECL or PECL level, ***/E pins should be used and ***/T pins left open. When the digital input level is TTL, ***/T pins should be used and III/E pins left open. Test Circuits +V 4V 1.95V VRT 5V 5V A ICC A AVCC DVCC1 DVCC2 VIN S2 - IEE VRB -V CLK/E DGND2 DGND1 AGND S1: ON WHEN A < B S2: ON WHEN A > B DGND3 A<B A>B COMPARATOR 5MHz PECL VIN 2V S1 + DVEE3 HI3026 8 “0” A8 TO A1 B8 TO B1 A0 B0 DVM CONTROLLER FIGURE 4. CURRENT CONSUMPTION MEASUREMENT CIRCUIT FN4109 Rev.3.00 August 1997 8 BUFFER “1” 000...00 TO 111..10 FIGURE 5. INTEGRAL LINEARITY ERROR/DIFFERENTIAL LINEARITY ERROR MEASUREMENT CIRCUIT Page 9 of 17 HI3026 Test Circuits (Continued) VIN SIGNAL SOURCE 8 HI3026 A LATCH COMPARATOR A>B PULSE COUNTER B fC 4 CLK -1kHz CLK + LATCH 2VP-P SINE WAVE 16 LSB SIGNAL SOURCE 1/ 8 fC FIGURE 6. ERROR RATE MEASUREMENT CIRCUIT VRT VRM2 VIN 100MHz VRB AMP CLK OSC1 : VARIABLE VIN fR 8 HI3026 129 t 128 127 VIN LOGIC ALALYZER (LSB) 126 125 CLK 1024 SAMPLES CLK OSC2 SAMPLING TIMING FLUCTUATION (= APERTURE JITTER) NOTE: Where (LSB) is the deviation of the output codes when the largest slew rate point is sampled at the clock which has exactly the same frequency as the analog input signal, the aperture jitter tAJ is: 256 t AJ = / ------- = / ---------- x 2f . 2 t ECL BUFFER 100MHz FIGURE 7. SAMPLING DELAY/APERTURE JITTER MEASUREMENT CIRCUIT FIGURE 8. APERTURE JITTER MEASUREMENT METHOD Operating Modes The HI3026 has two types of operating modes which are selected with Pin 45 (SELECT). TABLE 2. OPERATING MODE TABLE OPERATING MODE SELECT MAXIMUM CONVERSION RATE DMUX Mode VCC 120 MSPS Demultiplexed Output 60 MBPS The input clock is 1/2 frequency divided and output at 60MHz. Straight Mode GND 100 MSPS Straight Output 100 MBPS The input clock is inverted and output at 100MHz. DMUX Mode (See Application Circuits, Figures 18, 19, 20) Set the SELECT pin to VCC for this mode. In this mode, the clock frequency is divided by 2 in the IC, and the data is output after being demultiplexed by this 1/2 frequency divided clock. The 1/2 frequency divided clock, which has adequate setup time and hold time for the output data, is output from the CLKOUT pin. DATA OUTPUT CLOCK OUTPUT cause operation as shown in the figure below. As a countermeasure, the HI3026 is equipped with a function which resets the 1/2 frequency divided clock. When resetting this clock, the RESET pulse must be input to the RESET pin. See the Timing Charts for the RESET pulse input timing. The A/D converter can operate at fC (Min) = 120 MSPS in this mode. When using multiple HI3026 units in parallel in this mode, differences in the start timing of the 1/2 frequency divided clock may FN4109 Rev.3.00 August 1997 Page 10 of 17 HI3026 Straight Mode (See Application Circuits, Figures 21, 22, 23) Set the SELECT pin to GND for this mode. In this mode, data output can be obtained in accordance with the clock frequency applied to the A/D converter for applications which use the clock applied to the A/D converter as the system clock. The A/D converter can operate at fC (Min) = 100 MSPS in this mode. Digital Input Level and Supply Voltage Settings The logic input level for the HI3026 supports ECL, PECL and TTL levels. The power supplies (DVEE3 , DGND3) for the logic input block must be set to match the logic input (CLK and RESET signals) level. TABLE 3. LOGIC INPUT LEVEL AND POWER SUPPLY SETTINGS DIGITAL INPUT LEVEL DVEE3 DGND3 SUPPLY VOLTAGE APPLICATION CIRCUITS ECL -5V 0V ±5V Figures 18, 21 PECL 0V +5V +5V Figures 19, 22 TTL 0V +5V +5V Figures 20, 23 CLK HI3026 CLK CLK CLKOUT A 8 BITS DATA RESETN HI3026 CLK CLKOUT B 8 BITS DATA RESETN FIGURE 9. WHEN THE RESET PULSE IS NOT USED CLK RESET PULSE HI3026 CLK CLK CLKOUT A 8 BITS DATA RESETN HI3026 CLK RESET PULSE CLKOUT B RESETN 8 BITS DATA FIGURE 10. WHEN THE RESET PULSE IS USED FN4109 Rev.3.00 August 1997 Page 11 of 17 HI3026 Typical Performance Curves 170 CURRENT CONSUMPTION (mA) CURRENT CONSUMPTION (mA) 170 160 150 140 130 -25 25 160 150 140 fCLK -1kHz 4 DMUX MODE CL = 5pF fIN = 130 0 75 60 AMBIENT TEMPERATURE (oC) FIGURE 11. CURRENT CONSUMPTION vs AMBIENT TEMPERATURE CHARACTERISTICS FIGURE 12. CURRENT CONSUMPTION vs CONVERSION RATE CHARACTERISTICS RESPONSE VRT = 4V VRB = 2V 20 REFERENCE CURRENT (mA) ANALOG INPUT CURRENT (A) 120 CONVERSION RATE (MSPS) 200 100 15 10 0 2 3 -25 4 25 ANALOG INPUT VOLTAGE (V) FIGURE 13. ANALOG INPUT CURRENT vs ANALOG INPUT VOLTAGE CHARACTERISTICS FIGURE 14. REFERENCE CURRENT vs AMBIENT TEMPERATURE CHARACTERISTICS 50 fC = 120 MSPS ERROR RATE (TPS) 10-6 40 SNR (dB) 75 AMBIENT TEMPERATURE (oC) 30 fIN = fCLK -1kHz 4 ERROR > 16 LSB 10-7 10-8 10-9 10-10 20 1 3 5 10 30 INPUT FREQUENCY (MHz) FIGURE 15. SNR vs INPUT FREQUENCY RESPONSE FN4109 Rev.3.00 August 1997 50 120 140 160 CONVERSION RATE (MSPS) FIGURE 16. ERROR RATE vs CONVERSION RATE CHARACTERISTICS Page 12 of 17 HI3026 MAXIMUM CONVERSION (MSPS) Typical Performance Curves 170 160 (Continued) fIN = fCLK -1kHz 4 ERROR > 16 LSB ERROR RATE: 10-9 TPS 150 140 130 -25 25 75 AMBIENT TEMPERATURE (Co) FIGURE 17. MAXIMUM CONVERSION RATE vs AMBIENT TEMPERATURE CHARACTERISTICS Application Circuits +5V (D) DG ECL RESET PULSE 48 47 46 45 44 43 42 41 40 39 38 37 -5V (D) 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 P2D0 TO P2D7 8-BIT DIGITAL DATA 25 1 AG AG 2V +5V (A) DG 4V 12 8-BIT DIGITAL DATA LATCH DG +5V (D) DG 8-BIT DIGITAL DATA LATCH 13 14 15 16 17 18 19 20 21 22 23 24 ECL - CLK DG +5V (D) FIGURE 18. DMUX ECL INPUT FN4109 Rev.3.00 August 1997 Page 13 of 17 HI3026 Application Circuits (Continued) +5V (D) DG PECL RESET PULSE 48 47 46 45 44 43 42 41 40 39 38 37 DG 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 P2D0 TO P2D7 8-BIT DIGITAL DATA 25 1 DG AG 2V +5V (A) +5V (D) 4V 12 8-BIT DIGITAL DATA LATCH DG +5V (D) DG 8-BIT DIGITAL DATA LATCH 13 14 15 16 17 18 19 20 21 22 23 24 PECL - CLK DG +5V (D) FIGURE 19. DMUX PECL INPUT +5V (D) DG TTL RESET PULSE 48 47 46 45 44 43 42 41 40 39 38 37 DG 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 P2D0 TO P2D7 8-BIT DIGITAL DATA 25 1 AG AG 2V +5V (A) +5V (D) 4V 12 8-BIT DIGITAL DATA LATCH DG +5V (D) DG 8-BIT DIGITAL DATA LATCH 13 14 15 16 17 18 19 20 21 22 23 24 TTL - CLK DG +5V (D) FIGURE 20. DMUX TTL INPUT FN4109 Rev.3.00 August 1997 Page 14 of 17 HI3026 Application Circuits (Continued) DG +5V (D) DG 48 47 46 45 44 43 42 41 40 39 38 37 -5V (D) 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 1 AG AG 2V +5V (A) DG 4V 8-BIT DIGITAL DATA LATCH DG +5V (D) DG 25 12 13 14 15 16 17 18 19 20 21 22 23 24 ECL - CLK ECL - TTL DG +5V (D) FIGURE 21. STRAIGHT ECL INPUT © Copyright Intersil Americas LLC 1997-2002. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN4109 Rev.3.00 August 1997 Page 15 of 17 HI3026 Application Circuits (Continued) DG +5V (D) DG 48 47 46 45 44 43 42 41 40 39 38 37 DG 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 1 AG AG 2V +5V (A) +5V(D) 4V 8-BIT DIGITAL DATA LATCH DG +5V (D) DG 25 12 13 14 15 16 17 18 19 20 21 22 23 24 PECL - CLK PECL - TTL DG +5V (D) FIGURE 22. STRAIGHT PECL INPUT DG +5V (D) DG 48 47 46 45 44 43 42 41 40 39 38 37 DG 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 AG AG 1 2V +5V (A) +5V(D) 4V 8-BIT DIGITAL DATA LATCH DG +5V (D) DG 25 12 13 14 15 16 17 18 19 20 21 22 23 24 TTL - CLK DG +5V (D) FIGURE 23. STRAIGHT TTL INPUT FN4109 Rev.3.00 August 1997 Page 16 of 17 HI3026 Application Circuits (Continued) AG ANALOG INPUT AG + +5V (A) 1F DG + + 1F AG + 10F AG 12 11 10 9 8 7 6 5 4 3 2 DGND3 VRT AGND VRM3 AVCC VRM2 VIN AVCC VRM1 AGND VRB 1 RESETN/E 48 13 CLK/E 14 CLKN/E 15 CLK/T 16 NC SELECT 45 17 NC INV 44 18 NC CLKOUT 43 19 DVCC2 DVCC2 42 20 DGND2 DGND2 41 21 P2D0 P1D7 40 22 P2D1 P1D6 39 23 P2D2 P1D5 38 24 P2D3 P1D4 37 RESET/E 47 P2D6 (MSB) P2D7 P1D3 P2D5 32 33 34 35 36 P1D3 31 P1D2 DVCC2 30 P1D2 DVCC1 29 P1D1 DGND1 28 P1D1 P2D7 27 P1D0 P2D6 26 (LSB) P1D0 P2D5 25 DGND2 P2D4 RESETN/T 46 P2D4 P2D2 P2D3 + 2V 10F SHORT TTL CLK (LSB) P2D0 P2D1 + SHORT - P1D6 (MSB) P1D7 (D) AG + +5V P1D4 P1D5 - DVEE3 4V SHORT THE ANALOG SYSTEM AND DIGITAL SYSTEM AT ONE POINT IMMEDIATELY UNDER THE A/D CONVERTER. SEE THE NOTES ON OPERATION IS THE CHIP CAPACITOR OF 0.1F. FIGURE 24. STRAIGHT MODE TTL I/O (WHEN A SINGLE POWER SUPPLY IS USED) FN4109 Rev.3.00 August 1997 Page 17 of 17