Detector Switches/ESE18 1HL Detector Switches Type: Japan ESE18 Detector switches that contribute to miniaturization, weight reduction, and expansion of the operation variety required for portable equipment. n Features l Thin body: 1.2 mm l Circuit type: Normally-open and a normally-closed types are available. l Travel: Standard type: 1.5 mm Long type: 2.15 l Surface mounted type: Packed with embossed tape. Supports reflow soldering. n Recommended Applications l Mechanisms or the detection of media in portable equipment (e.g. MD/CD-ROM/DVD players, DSCs) l Operation switches (input devices) n Explanation of Part Numbers 1 2 3 4 5 E S E 1 8 6 7 9 Design No Product Code 6th 8 Type L Left-side operation type R Right-side operation type n Major Specifications Power Rating 50 µA 3 V dc to 10 mA 5 V dc Contact Resistance 1 W max. Insulation Resistance 100 MW max. (100 V dc) Dielectric Withstanding Voltage 100 V ac for 1 minute Operating Force 300 mN max. Full Travel 1.5 mm, 2.15 mm Operating Life 50000 cycles min. _10 ¡C to +60 ¡C Temperature Range Heat Resistance +70 ¡C for 96 hours _25 ¡C for 96 hours Low Temperature Resistance Humidity Resistance Minimum Quantity/Packing Unit Quantity/Carton +40 ¡C 90 % to 95 % RH for 96 hours ESE18L ESE18R ESE18L ESE18R 5000 pcs. (Reel Pack) 30000 pcs. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Detector Switches/ESE18 n Dimensions in mm (not to scale) 0.25 0.5 OFF angular terminal Operation point ) .7¡ n (14 2.6 max. d ir e o ti Nomal closed without Boss ESE18L61A 4¡ ) 2. 3.2 OFF start position 3.0 Pivot center 0.7 OFF start position Case center 0.5 0.7 ON start position Dummy terminal 0.25 1.8 0.25 0.4 Pivot center 3.6 0.5 2.7 Recommended PWB piercing Plan (Pitch tolerance: ±0.05) 4.0 0.5 1.2±0.2 ON angular terminal OFF angular terminal io n .4 û) d ir e 2 0 (5 Ac tio n ON start position 5 .6 OFF start position 5.4 3.2 0.54 2 1.2±0.2 Dummy terminal Mfg. No. 0.5 (Marking direction is arbitrary) 2.7 3.0 4.1 Case center 1.2 0.7 0.5 0.5 (Pivot center) 2 1.15 0.25 1.0 0.5 0.75 (2.0) 1.4 3 0.7 0.4 Full stroke position 0.25 5 2.6 max. Pivot center Operation point Nomal closed without Boss ESE18L61C 1 ON start position 3.4 2.0±0.1 Nomal closed with Boss ESE18L61D 2.9 0.6±0.05 1.0 2.6 4 (1.2) OFF start position Nomal Open without Boss ESE18LF01 ESE18L11C û) 4.7 (1 c t Nomal Open with Boss ESE18LF02 ESE18L11D Standard stroke type ESE18L Straight terminals 1-pole 1-throw R0.3 No. 2 3.8 1.2 0.25 0.54 1.0 0.75 (2) 2.9 2.0±0.1 3.4 Nomal closed with Boss ESE18L61B 2.6 f0.6±0.05 1.0 0 (5 Ac tio n (1.2) 1.4 Nomal Open without Boss ESE18LJ01 ESE18L11A 5.4 ON start position 5 .6 1.15 Full stroke position c Nomal Open with Boss ESE18LJ02 ESE18L11B Standard stroke type ESE18L J-bent terminals 1-pole 1-throw ON angular terminal R0 .3 No. 1 1.8 3.6 4.0 Recommended PWB piercing Plan (Pitch tolerance: ±0.05) 0.25 ON angular terminal OFF angular terminal 3.0 Case center 3.8 0.7 1.15 0.25 Pivot center Pivot center 0.7 0.5 2.0±0.1 0.75 1.0 1.4 (2) 2.9 2.6 io n f0.6±0.05 3.2 ect 3.4 5.4 d ir ) 4¡ 0.54 2. Full stroke position 1.0 Nomal closed with Boss ESE18R61B Dummy terminal 0.25 Nomal closed without Boss ESE18R61A Operation point (1.2) (5 Nomal Open without Boss ESE18RJ01 ESE18R11A n io ct A OFF start position R0.3 (1 4. 7¡ ) 2.6 max. 0. 65 ON start position 1.2 Nomal Open with Boss ESE18RJ02 ESE18R11B Standard stroke type ESE18R J-bent terminals 1-pole 1-throw 0.5 No. 3 0.25 0.4 0.5 2.7 0.5 4.0 1.2±0.2 1.8 3.6 Recommended PWB piercing Plan (Pitch tolerance: ±0.05) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Detector Switches/ESE18 n Dimensions in mm (not to scale) OFF angular terminal (1 0.5 0.25 1.15 0.5 2 3.0 1.2 Dummy terminal Mfg. No. 4.1 0.5 2 Case center 0.7 0.7 0.75 0.5 (Pivot center) Full stroke position Operation point 3 1.0 1.4 (2.0) 2.6 2.9 0.4 OFF start position 0.25 3.2 tion Pivot center 1 5.4 rec 0.6±0.05 di 3.4 2.0±0.1 û) 0.54 n tio OFF start position .4 Nomal closed without Boss ESE18R61C 4 2 1.0 û) 2.6 max. 0 .6 5 .3 R0 (1.2) 4.7 ON start position c A 5 Nomal Open without Boss ESE18RF01 ESE18R11C Nomal closed with Boss ESE18R61D ON angular terminal (5 Nomal Open with Boss ESE18RF02 ESE18R11D Standard stroke type ESE18R Straight terminals 1-pole 1-throw ON start position No. 4 (Marking direction is arbitrary) 2.7 4.0 1.8 3.6 1.2±0.2 Recommended PWB piercing Plan (Pitch tolerance: ±0.05) 0.5 ) 7¡ 4. 4¡ 2. 5.4 R0 0.54 3.2 0.25 0.5 0.4 2.7 0.5 Mfg. No. 3.8 3.6 Long stroke type ESE18L Straight terminals 1-pole 1-throw ON angular terminal OFF angular terminal ) 7¡ 4. .3 (5 2. ON start position OFF start position 5.4 0.54 3.2 1.15 0.25 Mfg. No. 3.0 (Marking direction is arbitrary) 4.1 1.2 0.5 2.7 4.0 Case center 0.7 0.5 0.7 0.75 0.5 (Pivot center) 1.4 1.0 (2.0) 3.1 3.55 1.2±0.2 Operation point 0.4 5 .6 0 Pivot center OFF start position 0.25 ON start position 3.4 2.0±0.1 f0.6±0.05 1.0 Nomal closed with Boss ESE18L62D (3.2) 4¡ (1.2) Full stroke position Nomal Open without Boss ESE18L12C ) (1 Nomal closed without Boss ESE18L62C 1.8 Recommended PWB piercing Plan (Pitch tolerance: ±0.05) R0 Nomal Open with Boss ESE18L12D 3.0 (Marking direction is arbitrary) 4.0 1.2±0.2 No. 6 1.15 Case center 1.2 0.7 0.5 0.7 0.75 (Pivot center) 1.4 1.0 Full stroke position 3.1 (2.0) OFF start position 2.0±0.1 3.4 0.25 0.25 OFF start position Pivot center Operation point f0.6±0.05 (5 1.0 ON start position 5 .6 0 .3 (1.2) Nomal closed with Boss ESE18L62B (3.2) ) (1 Nomal Open without Boss ESE18L12A Nomal closed without Boss ESE18L62A 0.25 OFF angular terminal 3.55 Nomal Open with Boss ESE18L12B Long stroke type ESE18L J-bent terminals ON angular terminal 1-pole 1-throw ON start position No. 5 1.8 3.6 Recommended PWB piercing Plan (Pitch tolerance: ±0.05) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Detector Switches/ESE18 n Dimensions in mm (not to scale) ON angular terminal OFF angular terminal (1 4. 7 OFF start position 0.25 1.0 0.25 0.5 1.8 2.7 0.5 3.6 4.0 Recommended PWB piercing Plan (Pitch tolerance: ±0.05) ON angular terminal OFF angular terminal (1 4. ON start position 0 1.2±0.2 Dummy terminal 0.5 2.7 3.0 Mfg. No. (Marking direction is arbitrary) 4.0 4.1 0.5 0.7 0.5 0.7 0.75 0.5 (Pivot center) 3.55 3.1 0.25 1.4 1.0 Full stroke position Operation point (2.0) Pivot center OFF start position ON start position 3.2 ¡) f0.6±0.05 5.4 4 3.4 2.0±0.1 2. 0.4 (5 0.54 0.25 5 3 1.0 ¡) .6 0. R Nomal closed without Boss ESE18R62C OFF start position (1.2) 7 (3.2) 1.15 0.4 Long stroke type ESE18R Straight terminals 1-pole 1-throw Nomal closed with Boss ESE18R62D 3.0 Dummy terminal 3.8 1.2 0.7 Case center 0.5 0.75 Pivot center Nomal Open without Boss ESE18R12C 3.2 Pivot center 0.7 (2.0) 1.4 3.55 3.1 f0.6±0.05 2.0±0.1 3.4 0.25 Nomal Open with Boss ESE18R12D 5.4 ¡) 0.54 1.2± 0.2 No. 8 .4 Full stroke position 3 0. Nomal closed with Boss ESE18R62B Nomal closed without Boss ESE18R62A Operation point 1.0 2 (5 (1.2) R Nomal Open without Boss ESE18R12A ¡) (3.2) 0 .6 5 1.15 ON start position Case center 1.2 Nomal Open with Boss ESE18R12B 0.25 Long stroke type ESE18R J-bent terminals 1-pole 1-throw 0.5 No. 7 1.8 3.6 Recommended PWB piercing Plan (Pitch tolerance: ±0.05) n Circuit Diagram Nomal Open type 1-pole 1-throw (N . O) Type ESE18L Dummy Type ESE18R Dummy Dummy C Common tarminal Common C tarminal Nomal Closed type 1-pole 1-throw (N . O) Type ESE18L Dummy Dummy Dummy Type ESE18R Common C tarminal Dummy Dummy C Common tarminal Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Detector Switches/ESE18 n Packaging Specifications Standard Reel Dimensions in mm (not to scale) Standard stroke type Long stroke type Taping Reel Embossed Carrier Taping f380.0±2.0 24.4 4.0±0.1 2.0±0.1 1 0. + 0 Pilot holes Drawing direction TOP Leading portion 400 mm min. 13.5 16.0±0.3 Carrier tape .5 2.0 2.0 END f1 7.5±0.1 P=8.0±0.1 1.75±0.1 (f80.0) Non-packed portion (160 mm min.) Non-packed portion Packed portion (100 mm min.) Cover tape Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately.