NXP IP4786CZ32 Dvi and hdmi interface esd and overcurrent protection, ddc/cec buffering, hot plug Datasheet

N3
2
QF
HV
IP4786CZ32
DVI and HDMI interface ESD and overcurrent protection,
DDC/CEC buffering, hot plug detect and backdrive protection
Rev. 1 — 15 April 2011
Product data sheet
1. General description
The IP4786CZ32 is designed to protect High-Definition Multimedia Interface (HDMI)
transmitter host interfaces. It includes HDMI 5 V overcurrent / overvoltage protection, Data
Display Channel (DDC) buffering and decoupling, hot plug detect, backdrive protection,
Consumer Electronic Control (CEC) buffering and decoupling, and ±8 kV contact
ElectroStatic Discharge (ESD) protection for all I/Os in accordance with the
IEC 61000-4-2, level 4 standard.
The IP4786CZ32 incorporates Transmission Line Clamping (TLC) technology on the
high-speed Transition Minimized Differential Signaling (TMDS) lines to simplify routing
and help reduce impedance discontinuities. All TMDS lines are protected by an
impedance-matched diode configuration that minimizes impedance discontinuities caused
by typical shunt diodes.
The enhanced 60 mA overcurrent / overvoltage linear regulator guarantees
HDMI-compliant 5 V output voltage levels with up to 6.5 V inputs.
The DDC lines use a new buffering concept which decouples the internal capacitive load
from the external capacitive load for use with standard Complementary Metal Oxide
Semiconductor (CMOS) or Low Voltage Transistor-Transistor Logic (LVTTL) I/O cells
down to 1.8 V. This buffering also redrives the DDC and CEC signals, allowing the use of
longer or cheaper HDMI cables with a higher capacitance. The internal hot plug detect
module simplifies the application of the HDMI transmitter to control the hot plug signal.
All lines provide appropriate integrated pull-ups and pull-downs for HDMI compliance and
backdrive protection to guarantee that HDMI interface signals are not pulled down if the
system is powered down or enters Standby mode. Only a single external capacitor is
required for operation.
2. Features and benefits
„ HDMI 1.3a and 1.4, 340 MHz pixel clock, deep color and HDMI Ethernet and Audio
return Channel (HEAC) compatible
„ Pb-free, Restriction of Hazardous Substances (RoHS) compliant and free of halogen
and antimony (Dark Green compliant)
„ Robust ESD protection without degradation after repeated ESD strikes
„ Impedance matched 100 Ω differential transmission line ESD protection for
TMDS lines (±10 Ω). No Printed-Circuit Board (PCB) pre-compensation required
„ All external I/O lines with ESD protection of at least ±8 kV in accordance with the
IEC 61000-4-2, level 4 standard
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
„ DDC capacitive decoupling between system side and HDMI connector side and
buffering to drive cable with high capacitive load (> 700 pF/25 m)
„ Hot plug detect module
„ CEC buffering and isolation, with integrated backdrive-protected 26 kΩ pull-up
„ Simplified flow-through routing utilizing less overall PCB space
„ Highest integration in a small footprint, PCB level, optimized RF routing,
32-pin HVQFN leadless package
3. Applications
„ The IP4786CZ32 can be used for a wide range of HDMI source devices, consumer
and computing electronics:
‹ Standard-Definition (SD) and High-Definition (HD) DVD player
‹ Set-top box
‹ PC graphic card
‹ Game console
‹ HDMI picture performance quality enhancer module
‹ Digital Visual Interface (DVI)
4. Ordering information
Table 1.
Ordering information
Type number
Package
Name
IP4786CZ32
IP4786CZ32
Product data sheet
Description
Version
HVQFN32 plastic thermal enhanced very thin quad flat package; SOT617-3
no leads; 32 terminals; body 5 × 5 × 1 mm
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
2 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
5. Functional diagram
TMDS_D2+_SYS
TMDS_D2+_CON
ESD
TMDS_D2–_SYS
TMDS_D2–_CON
TMDS_D1+_SYS
TMDS_D1+_CON
TMDS_D1–_SYS
TMDS_D1–_CON
TMDS_D0+_SYS
TMDS_D0+_CON
TMDS_D0–_SYS
TMDS_D0–_CON
TMDS_CK+_SYS
TMDS_CK+_CON
8 kV
TMDS_CK–_SYS
TMDS_CK–_CON
VCC(5V0)
ESD
3.3 V VOLTAGE
REGULATOR
VCC(SYS)
ESD
CEC driver
10 kΩ
26 kΩ
CEC_SYS
CEC_CON
2 kV
ESD
8 kV
VCC(SYS)
HDMI_5V0_CON
ESD
DDC driver
3.65 kΩ
1.85 kΩ
DDC_CLK_SYS
DDC_CLK_CON
2 kV
VCC(SYS)
ESD
HDMI_5V0_CON
8 kV
ESD
DDC driver
3.65 kΩ
1.85 kΩ
DDC_DAT_SYS
DDC_DAT_CON
2 kV
8 kV
Hot plug
ESD
ESD
HOTPLUG_DET_SYS
HOTPLUG_DET_CON
100 kΩ
100 kΩ
2 kV
8 kV
ESD
ESD
HDMI_5V0_CON
VCC(5V0)
8 kV
2 kV
ESD
ESD_BYPASS
CURRENT LIMITER
VCC(SYS)
8 kV
clamp
VCC(5V0)
ESD
ESD
enable
enLim
enRef
POWER
MANAGEMENT UNIT
CEC_STBY
enCEC
VCC(SYS)
VCC(SYS)
100 kΩ
2 kV
VCC(5V0)
ESD
2 kV
ibias 1..n
vref 1..m
CURRENT-/VOLTAGEREFERENCES
Fig 1.
IP4786CZ32
Product data sheet
n
m
UTILITY_CON
100 kΩ
8 kV
001aan369
Functional diagram
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
3 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
6. Pinning information
25 CEC_CON
26 ESD_BYPASS
27 VCC(SYS)
28 CEC_STBY
29 CEC_SYS
30 n.c.
terminal 1
index area
31 n.c.
32 HOTPLUG_DET_SYS
6.1 Pinning
TMDS_D2+_SYS
1
24 TMDS_D2+_CON
TMDS_D2–_SYS
2
23 TMDS_D2–_CON
TMDS_D1+_SYS
3
22 TMDS_D1+_CON
TMDS_D1–_SYS
4
TMDS_D0+_SYS
5
TMDS_D0–_SYS
6
19 TMDS_D0–_CON
TMDS_CK+_SYS
7
18 TMDS_CK+_CON
TMDS_CK–_SYS
8
17 TMDS_CK–_CON
21 TMDS_D1–_CON
UTILITY_CON 16
20 TMDS_D0+_CON
DDC_CLK_CON 15
DDC_DAT_CON 14
HDMI_5V0_CON 13
HOTPLUG_DET_CON 12
VCC(5V0) 11
9
DDC_CLK_SYS
DDC_DAT_SYS 10
IP4786CZ32
018aaa083
Transparent top view
Fig 2.
Pin configuration IP4786CZ32
6.2 Pin description
Table 2.
IP4786CZ32
Product data sheet
Pin description
Pin
Name
Description
1
TMDS_D2+_SYS
TMDS to ASIC inside system
2
TMDS_D2−_SYS
TMDS to ASIC inside system
3
TMDS_D1+_SYS
TMDS to ASIC inside system
4
TMDS_D1−_SYS
TMDS to ASIC inside system
5
TMDS_D0+_SYS
TMDS to ASIC inside system
6
TMDS_D0−_SYS
TMDS to ASIC inside system
7
TMDS_CK+_SYS
TMDS to ASIC inside system
8
TMDS_CK−_SYS
TMDS to ASIC inside system
9
DDC_CLK_SYS
DDC clock system side
10
DDC_DAT_SYS
DDC data system side
11
VCC(5V0)
5 V supply input
12
HOTPLUG_DET_CON
hot plug detect connector side
13
HDMI_5V0_CON
5 V overcurrent out to connector
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
4 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
Table 2.
IP4786CZ32
Product data sheet
Pin description …continued
Pin
Name
Description
14
DDC_DAT_CON
DDC data connector side
15
DDC_CLK_CON
DDC clock connector side
16
UTILITY_CON
utility line ESD protection
17
TMDS_CK−_CON
TMDS ESD protection to connector
18
TMDS_CK+_CON
TMDS ESD protection to connector
19
TMDS_D0−_CON
TMDS ESD protection to connector
20
TMDS_D0+_CON
TMDS ESD protection to connector
21
TMDS_D1−_CON
TMDS ESD protection to connector
22
TMDS_D1+_CON
TMDS ESD protection to connector
23
TMDS_D2−_CON
TMDS ESD protection to connector
24
TMDS_D2+_CON
TMDS ESD protection to connector
25
CEC_CON
CEC signal connector side
26
ESD_BYPASS
ESD bias voltage
27
VCC(SYS)
supply voltage for level shifting
28
CEC_STBY
CEC Standby mode control (LOW for lowest
power, CEC-only mode)
29
CEC_SYS
CEC I/O signal system side
30
n.c.
not connected
31
n.c.
not connected
32
HOTPLUG_DET_SYS
hot plug detect system side
ground pad
GND
ground
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
5 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
7. Limiting values
Table 3.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
VCC(5V0)
supply voltage (5.0 V)
VI
input voltage
I/O pins
VESD
electrostatic discharge
voltage
IEC 61000-4-2, level 4 (contact)
[1]
-
±8
kV
IEC 61000-4-2, level 1 (contact)
[2]
-
±2
kV
total power dissipation
DDC operating at 100 kHz;
CEC operating at 1 kHz;
50 % duty cycle; CEC_STBY = HIGH;
no current at HDMI_5V0_CON
-
50
mW
DDC and CEC bus in idle mode;
CEC_STBY = HIGH;
no current at HDMI_5V0_CON
-
3.0
mW
DDC and CEC bus in idle mode;
CEC_STBY = LOW
-
1.0
mW
Ptot
Conditions
Min
Max
GND − 0.5 6.5
Unit
V
GND − 0.5 5.5
V
Tamb
ambient temperature
−25
+85
°C
Tstg
storage temperature
−55
+125
°C
[1]
Connector-side pins (typically denoted with “_CON” suffix) to ground.
[2]
System-side pins: CEC_SYS, DDC_DAT_SYS, DDC_CLK_SYS, HOTPLUG_DET_SYS, CEC_STBY, VCC(SYS) and VCC(5V0).
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
6 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
8. Static characteristics
Table 4.
Supplies
Tamb = −25 °C to +85 °C unless otherwise specified.
Symbol
Parameter
Conditions
VCC(5V0)
supply voltage (5.0 V)
VCC(SYS)
system supply voltage
[1]
[1]
Min
Typ
Max
Unit
4.5
5.0
6.5
V
1.62
3.3
5.5
V
The IP4786CZ32 contains a 5 V voltage regulator function for higher input voltages.
Any input voltage of 4.925 V < VCC(5V0) < 6.50 V will provide HDMI compliant output levels of 4.8 V to 5.3 V
on HDMI_5V0_CON.
Table 5.
TMDS protection circuit
Tamb = −25 °C to +85 °C unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max Unit
90
100
110
Ω
-
0.6
-
pF
6.0
-
9.0
V
positive transient
-
1.0
-
Ω
negative transient
-
1.0
-
Ω
TMDS channel
Zi(dif)
differential input
impedance
TDR measured;
tr = 200 ps
Ceff
effective capacitance
equivalent shunt
capacitance for TDR
minimum; tr = 200 ps
[1][2]
Protection diode
VBRzd
Zener diode breakdown
voltage
I = 1.0 mA
rdyn
dynamic resistance
surge; I = 1.0 A;
IEC 61000-4-5/9
TLP
Product data sheet
[3]
-
1.0
-
Ω
negative transient
[3]
-
1.0
-
Ω
[4][5]
Ibck
back current
VCC(5V0) < Vch(TMDS)
ILR
reverse leakage current
VI = 3.0 V
VF
forward voltage
VCL(ch)trt(pos) positive transient channel
clamping voltage
IP4786CZ32
positive transient
[1]
This parameter is guaranteed by design.
100 ns TLP;
50 Ω pulser at 50 ns
-
0.1
1.0
μA
-
1.0
-
μA
-
0.7
-
V
-
8.0
-
V
[2]
Capacitive dip at HDMI Time Domain Reflectometer (TDR) measurement conditions.
[3]
ANSI-ESDSP5.5.1-2004, ESD sensitivity testing Transmission Line Pulse (TLP) component level
method 50 TDR.
[4]
Signal pins:
TMDS_D0+_CON, TMDS_D0−_CON, TMDS_D1+_CON, TMDS_D1−_CON, TMDS_D2+_CON,
TMDS_D2−_ΧΟΝ, TMDS_CK+_CON, TMDS_CK−_CON,
TMDS_D0+_SYS, TMDS_D0−_SYS, TMDS_D1+_SYS, TMDS_D1−_SYS, TMDS_D2+_SYS,
TMDS_D2−_ΣΨΣ, TMDS_CK+_SYS and TMDS_CK−_SYS.
[5]
Backdrive current from TMDS_x_SYS and TMDS_x_CON pins to local VCC(5V0) bias rail at power-down.
Device does not block backdrive current leakage through the device to/from ASIC I/O pins connected
to TMDS_x_SYS pins.
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
7 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
Table 6.
HDMI_5V0_CON
Tamb = −25 °C to +85 °C unless otherwise specified.
Symbol
Parameter
Conditions
rdyn
dynamic resistance
TLP
Min
Typ
Max Unit
positive transient
[1]
-
1.0
-
Ω
negative transient
[1]
-
1.0
-
Ω
VCL
clamping voltage
100 ns TLP;
50 Ω pulser at 50 ns
-
8
-
V
IO(max)
maximum output current
V(HDMI_5V0_CON) = 4.8 V
55
-
-
mA
Ibck
back current
VCC(5V0) < V(HDMI_5V0_CON)
-
-
10
μA
IO(sc)
short-circuit output current V(HDMI_5V0_CON) = 0 V
-
125
175
mA
-
70
-
mV
-
-
125
mV
4.8
5.05 5.3
dropout voltage
Vdo
4.5 V < VCC(5V0) < 4.925 V;
DDC = LOW
[2]
IO = 10 mA
IO = 55 mA
VO(LDO)
LDO output voltage
IO ≤ 55 mA;
4.925 V < VCC(5V0) < 6.5 V;
DDC = LOW
[2]
V
[1]
ANSI-ESDSP5.5.1-2004, ESD sensitivity testing TLP component level method 50 TDR.
[2]
The IP4786CZ32 contains a 5 V voltage regulator function for higher input voltages.
Any input voltage of 4.925 V < VCC(5V0) < 6.50 V will provide HDMI compliant output levels of 4.8 V to 5.3 V
on HDMI_5V0_CON
Table 7.
UTILITY_CON
Tamb = −25 °C to +85 °C unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max Unit
Supplies: pins VCC(5V0) and VCC(SYS)
rdyn
Product data sheet
TLP
positive transient
[1]
-
1.0
-
Ω
negative transient
[1]
-
1.0
-
Ω
VCL
clamping voltage
100 ns TLP;
50 Ω pulser at 50 ns
-
8.0
-
V
Ci
input capacitance
VCC(5V0) = 0 V;
VCC(SYS) = 0 V; Vbias = 2.5 V;
AC input = 3.5 V(p-p);
f = 100 kHz
-
8.0
10
pF
Rpd
pull-down resistance
60
100
140
kΩ
[1]
IP4786CZ32
dynamic resistance
ANSI-ESDSP5.5.1-2004, ESD sensitivity testing TLP component level method 50 TDR.
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
8 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
Table 8.
Static characteristics
Tamb = −25 °C to +85 °C unless otherwise specified.
Symbol
Parameter
Conditions
DDC buffer on connector
Min
Typ
Max
Unit
V
side[1]
VIH
HIGH-level input voltage
0.5 ×
V(HDMI_5V0_CON)
6.5
VIL
LOW-level input voltage
−0.5
-
0.3 ×
V
V(HDMI_5V0_CON)
VOL
LOW-level output voltage
internal pull-up and
external sink
-
100
200
mV
VIK
input clamping voltage
II = −18 mA
-
-
−1.0
V
VOH
HIGH-level output voltage
CIO
input/output capacitance
Rpu
pull-up resistance
DDC buffer on system
VIH
VIL
VOL
VIK
LOW-level input voltage
LOW-level output voltage
input clamping voltage
VOH
HIGH-level output voltage
CIO
input/output capacitance
Rpu
pull-up resistance
Product data sheet
V(HDMI_5V0_CON) − 0.02
V(HDMI_5V0_CON) V
+ 0.02
-
8.0
10
pF
1.6
1.8
2.0
kΩ
VCC(SYS) = 1.8 V
450
-
-
mV
VCC(SYS) = 2.5 V
620
-
-
mV
VCC(SYS) = 3.3 V
760
-
-
mV
VCC(SYS) = 5.0 V
800
-
-
mV
VCC(SYS) = 1.8 V
-
-
330
mV
VCC(SYS) = 2.5 V
-
-
370
mV
VCC(SYS) = 3.3 V
-
-
390
mV
VCC(SYS) = 5.0 V
-
-
410
mV
VCC(SYS) = 1.8 V
-
-
500
mV
VCC(SYS) = 2.5 V
-
-
700
mV
VCC(SYS) = 3.3 V
-
-
810
mV
VCC(SYS) = 5.0 V
-
-
850
mV
-
-
−1.0
V
VCC(5V0) = 5.0 V;
VCC(SYS) = 3.3 V;
CEC_STBY = HIGH
[2][3]
side[1][4]
HIGH-level input voltage
IP4786CZ32
[2]
II = −18 mA
VCC(5V0) = 0 V;
VCC(SYS) = 0 V;
Vbias = 2.5 V;
AC input = 3.5 V(p-p);
f = 100 kHz
[2]
VCC(SYS) − 0.02 -
VCC(SYS) + 0.02 V
[2]
-
6.0
8.0
pF
3.2
3.65
4.1
kΩ
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
9 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
Table 8.
Static characteristics …continued
Tamb = −25 °C to +85 °C unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
2.0
-
-
V
CEC_CON[1]
VIH
HIGH-level input voltage
VIL
LOW-level input voltage
-
-
0.80
V
VOH
HIGH-level output voltage
2.88
3.3
3.63
V
VOL
LOW-level output voltage
-
100
200
mV
-
8.0
10
pF
23.4
26.0
28.6
kΩ
VCC(SYS) = 1.8 V
450
-
-
mV
VCC(SYS) = 2.5 V
620
-
-
mV
VCC(SYS) = 3.3 V
760
-
-
mV
VCC(SYS) = 5.0 V
800
-
-
mV
VCC(SYS) = 1.8 V
-
-
330
mV
VCC(SYS) = 2.5 V
-
-
370
mV
VCC(SYS) = 3.3 V
-
-
390
mV
VCC(SYS) = 5.0 V
-
-
410
mV
VCC(SYS) = 1.8 V
-
-
500
mV
VCC(SYS) = 2.5 V
-
-
700
mV
VCC(SYS) = 3.3 V
-
-
810
mV
VCC(SYS) = 5.0 V
-
-
850
mV
CIO
input/output capacitance
Rpu
pull-up resistance
IOL = 1.5 mA
VCC(5V0) = 0 V;
VCC(SYS) = 0 V;
Vbias = 2.5 V;
AC input = 3.5 V(p-p);
f = 100 kHz
[2]
CEC_SYS[1][4]
VIH
VIL
VOL
HIGH-level input voltage
LOW-level input voltage
LOW-level output voltage
HIGH-level output voltage
[2]
VCC(SYS) − 0.02 -
VCC(SYS) + 0.02 V
CIO
input/output capacitance
[2]
-
6.0
7.0
pF
Rpu
pull-up resistance
8.5
10
11.5
kΩ
VOH
VCC(5V0) = 0 V;
VCC(SYS) = 0 V;
Vbias = 2.5 V;
AC input = 3.5 V(p-p);
f = 100 kHz
HOTPLUG_DET_CON[1]
VIH
HIGH-level input voltage
2.0
-
-
V
VIL
LOW-level input voltage
-
-
0.8
V
Rpd
pull-down resistance
60
100
140
kΩ
Ci
input capacitance
-
8.0
10
pF
IP4786CZ32
Product data sheet
VCC(5V0) = 0 V;
VCC(SYS) = 0 V;
Vbias = 2.5 V;
AC input = 3.5 V(p-p);
f = 100 kHz
[2]
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
10 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
Table 8.
Static characteristics …continued
Tamb = −25 °C to +85 °C unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
0.7 × VCC(SYS)
-
-
V
HOTPLUG_DET_SYS[1]
VOH
HIGH-level output voltage IOL = 1 mA
VOL
LOW-level output voltage
Rpd
pull-down resistance
IOL = −1 mA
-
200
300
mV
60
100
140
kΩ
[1]
The device is active if the input voltage at pin CEC_STBY is above the HIGH level.
[2]
This parameter is guaranteed by design.
[3]
Capacitive load measured at power on.
[4]
No external pull-up resistor attached.
Table 9.
CEC_STBY power management circuit
VCC(SYS) = 1.62 V to 5.5 V; VCC(5V0) = 4.5 V to 6.5 V; GND = 0 V; Tamb = −25 °C to +85 °C unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Board side: input pin CEC_STBY[1]
VIH
HIGH-level input voltage
VIL
LOW-level input voltage
Rpd
pull-down resistance
Ci
input capacitance
[1]
HIGH = active
[2]
1.2
-
6.5
V
LOW = standby
[3]
−0.5
-
0.8
V
60
100
140
kΩ
-
6
7
pF
VI = 3 V or 0 V
The CEC_STBY pin should be connected permanently to VCC(5V0) or VCC(SYS) if no enable control is needed.
[2]
DDC buffers, Hot Plug Detect (HPD) buffer, and HDMI_5V0_CON out enabled; CEC buffer enabled.
[3]
DDC buffers, HPD buffer, and HDMI_5V0_CON out disabled; CEC buffer enabled.
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
11 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
9. Dynamic characteristics
Table 10. Dynamic characteristics
VCC(5V0) = 5.0 V; VCC(SYS) = 1.8 V; GND = 0 V; Tamb = −25 °C to +85 °C unless otherwise specified.
Symbol
Parameter
Conditions
DDC_DAT_SYS, DDC_CLK_SYS, DDC_DAT_CON,
Min
Typ
Max
Unit
DDC_CLK_CON[1]
tPLH
LOW to HIGH propagation delay
system side to connector side Figure 16
-
80
-
ns
tPHL
HIGH to LOW propagation delay
system side to connector side Figure 16
-
60
-
ns
tPLH
LOW to HIGH propagation delay
connector side to system side Figure 17
-
120
-
ns
tPHL
HIGH to LOW propagation delay
connector side to system side Figure 17
-
80
-
ns
tTLH
LOW to HIGH transition time
connector side Figure 18
-
150
-
ns
tTHL
HIGH to LOW transition time
connector side Figure 18
-
100
-
ns
tTLH
LOW to HIGH transition time
system side Figure 19
-
250
-
ns
tTHL
HIGH to LOW transition time
system side Figure 19
-
80
-
ns
[1]
All dynamic measurements are done with a 75 pF load. Rise times are determined by internal pull-up resistors.
018aaa084
120
018aaa085
120
Zdif
(Ω)
Zdif
(Ω)
80
80
40
40
0
41.4
41.6
41.8
0
41.4
42.0
41.6
41.8
t (ns)
42.0
t (ns)
tr = 200 ps; no filter
tr = 200 ps; no filter
(1) 100 Ω differential (CH1+CH2)
100 Ω differential (CH1+CH2)
(2) 50 Ω CH1, CH2
Fig 3.
Differential TDR plot (powered)
IP4786CZ32
Product data sheet
Fig 4.
Differential TDR plot (unpowered)
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
12 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
018aaa086
3
Sdd21;
Scc21
(dB)
(1)
–3
(2)
–9
–15
106
107
108
109
1010
f (Hz)
(1) Sdd21
(2) Scc21
Normalized to 100 Ω; differential pairs at signal pins.
Fig 5.
Mixed-mode differential and common-mode insertion loss; typical values
018aaa087
3
Sdd21
(dB)
(1)
–3
(2)
–9
–15
106
107
108
109
1010
f (Hz)
(1) Sdd21; Near End Crosstalk (NEXT)
(2) Sdd21; Far End Crosstalk (FEXT)
normalized to 100 Ω; differential pairs CH1/CH2 versus CH3/CH4
Fig 6.
IP4786CZ32
Product data sheet
Mixed-mode differential and common-mode NEXT / FEXT; typical values
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
13 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
018aaa088
018aaa089
1080p, 225 MHz pixel clock
Fig 7.
1080p, 225 MHz pixel clock
Eye diagram using reference PCB
Fig 8.
Eye diagram using IP4786CZ32
018aaa090
0.4
Cd
(pF)
0.2
0.0
–0.2
–0.4
–1.0
1.0
3.0
5.0
7.0
Vbias (V)
Deviation from typical capacitance normalized at Vbias = 2.5 V
Fig 9.
Line capacitance as a function of bias voltage; typical values
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
14 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
018aaa091
4.00
018aaa092
2.5
VCL
(V)
VCL
(V)
3.75
2.0
3.50
1.5
3.25
3.00
0.5
0.6
0.7
0.8
0.9
1.0
1.1
I (A)
1.2
1.0
0.4
0.6
0.8
1.0
1.2
I (A)
IEC 61000-4-5; tp = 8/20 μs; positive pulse
IEC 61000-4-5; tp = 8/20 μs; negative pulse
Fig 10. Dynamic resistance with positive clamping
Fig 11. Dynamic resistance with negative clamping
018aaa093
14
I
(A)
12
0
I
(A)
–2
10
–4
8
–6
6
–8
4
–10
2
–12
0
6
10
14
18
22
018aaa094
–14
–12
VCL (V)
0
tp = 100 ns; TLP; signal pins; typical values
Fig 12. Dynamic resistance with positive clamping
Product data sheet
–4
VCL (V)
tp = 100 ns; TLP; signal pins; typical values
IP4786CZ32
–8
Fig 13. Dynamic resistance with negative clamping
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
15 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
018aaa095
6.5
018aaa096
6.0
VI
(V)
VO
(V)
6.0
(2)
(5)
(4)
(1)
4.0
5.5
(1)
2.0
(3)
5.0
(4)
(3)
(2)
4.5
5.0
5.5
6.0
6.5
0.0
0.00
0.02
0.04
VCC(5V0) (V)
(1) 5.3 V; maximum values; HDMI CTS TID 7-11
(1) VCC(5V0) = 4.5 V
(2) 4.8 V; minimum values; HDMI CTS TID 7-11
(2) VCC(5V0) = 5.0 V
(3) I = 0 mA
(3) VCC(5V0) = 5.5 V
(4) I = 55 mA
(4) VCC(5V0) = 6.5 V
0.06
0.08
0.10
0.12
IO (A)
0.14
(5) VCC(5V0) supply input; 4.925 V to 6.5 V
Fig 14. Overvoltage limiter function (HDMI_5V0_CON)
IP4786CZ32
Product data sheet
Fig 15. Overcurrent limiter function (HDMI_5V0_CON)
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
16 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
10. AC waveforms
10.1 DDC propagation delay
VCC(SYS)
DDC system side
0.5 VCC(SYS)
0.28 VCC(SYS)
VOL
V(HDMI_5V0_CON)
DDC connector side
0.5 V(HDMI_5V0_CON)
0.5 V(HDMI_5V0_CON)
VOL
tPHL
tPLH
018aaa097
Fig 16. Propagation delay DDC, DDC system side to DDC connector side
V(HDMI_5V0_CON)
DDC connector side
0.5 V(HDMI_5V0_CON)
0.5 V(HDMI_5V0_CON)
VOL
VCC(SYS)
DDC system side
0.5 VCC(SYS)
0.5 VCC(SYS)
VOL
tPHL
tPLH
018aaa098
Fig 17. Propagation delay DDC, DDC connector side to DDC system side
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
17 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
10.2 DDC transition time
DDC system side
VCC(SYS)
VOL
V(HDMI_5V0_CON)
DDC connector side
80 % V(HDMI_5V0_CON)
20 % V(HDMI_5V0_CON)
VOL
tPHL
tPLH
018aaa099
Fig 18. Transition time DDC connector side
V(HDMI_5V0_CON)
DDC connector side
VOL
VCC(SYS)
DDC system side
80 % VCC(SYS)
20 % VCC(SYS)
VOL
tPHL
tPLH
018aaa100
Fig 19. Transition time DDC system side
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
18 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
11. Application information
11.1 TMDS ESD
To protect the TMDS lines and also to comply with the impedance requirements of the
HDMI specification, the IP4786CZ32 provides ESD protection with matched
TLC ESD structures. Typical Dual Rail Clamp (DRC) or rail-to-rail shunt structures are
common for low-capacitance ESD protection (as shown on the left side of Figure 20)
where the dominant factor for the TMDS line impedance dip is determined by the
capacitive load to ground. Parasitic lead inductances of the packaging in this case works
against the ESD clamping performance by including the ΔI/Δt reactance of the inductance
into the path of the ESD shunt.
The IP4786CZ32 utilizes these inherent inductances in series with the transmission line in
order to present an effective capacitive load of roughly only 0.7 pF. This TLC structure
minimizes the capacitive dip, for ideal signal integrity (Figure 20; right side) without
complicated PCB pre-compensation. As a beneficial side effect, this enhances the
ESD performance of the device as well, since the reactance of the series inductance
attenuates the fast initial peak of the ESD pulse, for a lower residual pulse delivered to the
Application Specific Integrated Circuit (ASIC).
018aaa102
018aaa101
a. Classic parallel ESD shunt protection
b. Improved series shunt TLC clamping
Fig 20. TLC ESD protection of TMDS lines
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
19 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
11.2 DDC circuit
The DDC bus circuit integrates all required pull-ups, and provides full capacitive
decoupling between the HDMI connector and the DDC bus lines on the PCB. The
capacitive decoupling ensures that the maximum capacitive load is well within the 50 pF
maximum of the HDMI specification. No external pull-ups or pull-downs are required.
The bidirectional buffers support high-capacitive load on the HDMI cable-side. Various
non-compliant but prevalent low-cost cables have been observed with a capacitive load of
up to 6 nF on the DDC lines, far exceeding the 700 pF HDMI limit. The IP4786CZ32 can
easily decouple this from the weaker ASIC I/O buffers, and drive the rogue cable
successfully.
ESD_BYPASS
HDMI_5V0_CON
1.85 kΩ
ESD_BYPASS
VCC(SYS)
VCC(SYS)
1.85 kΩ
3.65 kΩ
3.65 kΩ
DDC_DAT_SYS
DDC_DAT_CON
DDC_DAT_SYS
DDC_CLK_CON
HDMI_5V0_CON
018aaa104
018aaa103
a. DDC clock
b. DDC data
Fig 21. DDC circuit
5
(1)
4
V
3
2
(2)
1
0
time
018aaa105
(1) Valid I2C signaling example on the cable (connector side) from 5 V (HIGH) to approximately 1 V (LOW).
(2) Valid logic-level signaling example to the ASIC (system side) from 1.8 V (HIGH) to approximately 0.5 V (LOW).
Fig 22. DDC level shifting waveform example
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
20 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
11.3 Logic low I2C voltage shifter
The DDC buffers provide an additional feature commonly required for high-integration
HDMI ASICs which are limited to CMOS or LVTTL LOW-level input voltage (VIL) on their
available I/O buffer cells. These I/Os are not strictly compliant with the 0.3 VDD threshold
voltage levels of I2C and may miss intended logic low levels on the cable between 0.8 V
and 1.5 V (typical values).
This feature is also included in the CEC buffer, and thus allows standard I/O buffer cells to
be used in ASICs and microcontrollers.
018aaa106
0.9
(1)
VOL;VIH;
VIL
(V)
(2)
0.7
(3)
0.5
0.3
1.6
2.6
3.6
4.6
5.6
VCC(SYS) (V)
(1) VOL(max) driven to system (ASIC) side when I2C logic low (less than 0.3 × HDMI_5V0_CON)
(2) VIH(min) threshold on system (ASIC) side to drive I2C logic low
(3) VIL(max) threshold on system (ASIC) side to drive I2C logic low
Fig 23. Logic voltage thresholds as a function of supply voltage; on connector
(HDMI) side
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
21 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
11.4 Hot plug detect circuit and HEAC support
The IP4786CZ32 includes a hot plug detect circuit that simplifies the hot plug application.
The circuit generates a standard logic level from the hot plug signal.
The hot plug detect circuit is pulling down the signal to avoid any floating signal.
The comparator guarantees a save detection of the 2 V hot plug signal without any
glitches or oscillation at the hot plug output.
The IP4786CZ32 also provides an additional ESD pin to protect the reserved / HEAC pin
along with hot plug detect to 8 kV IEC 61000-4-2, level 4.
ESD_BYPASS VCC(5V0)
HOTPLUG_DET_CON
HOTPLUG_DET_SYS
100 kΩ
100 kΩ
018aaa107
Fig 24. Hot plug detect circuit
11.5 CEC
The logical multidrop topology of the CEC bus can include complex physical stubs,
loading cables, and interconnects that may deteriorate signal quality.
The IP4786CZ32 includes a full bidirectional buffer to drive the CEC bus and isolate
the CEC microcontroller or ASIC General-Purpose Input/Output (GPIO).
The CEC buffer derives power from an on-board 3.3 V regulator from the VCC(5V0) domain
(see Figure 25). This allows extensive system power management configurations and
guarantees an HDMI compliant V(CEC_CON) on the connector, as well as the
backdrive-protected 125 μA nominal CEC pull-up which does not degrade the bus when
powered down.
By placing the CEC microcontroller and VCC(5V0) input on a 5 V rail as shown in Figure 28,
the CEC microcontroller can communicate over CEC for power commands, and then
enable the HDMI port via the CEC_STBY pin, as well as the rest of the system as needed.
If IP4786CZ32 Standby modes are not required, or if the Power-down modes are not
desired, the CEC_STBY pin can be pulled HIGH to VCC(5V0) or VCC(SYS) for continuous
HDMI and CEC operation.
Strapping the CEC_STBY = VCC(SYS) = VDD of ASIC guarantees that all interface signals
ending with the suffix “_SYS” on the system side will be disabled when VCC(SYS) goes low,
protecting the ASIC I/O signals from exceeding its local VDD. In this mode, even if VCC(5V0)
is powered, HDMI_5V0_CON go active and hot plug events can be detected only when
the ASIC power supply rail is on.
Strapping CEC_STBY = VCC(5V0) is the most basic configuration where the buffers are
enabled whenever the local VCC(5V0) and VCC(SYS) supplies reach minimum operating
levels.
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
22 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
ESD_BYPASS
VCC(5V0)
VCC(SYS)
3V3
10 kΩ
26 kΩ
CEC_SYS
CEC_CON
018aaa108
Fig 25. CEC module
11.6 Backdrive protection
The HDMI connector contains various signals which can partly supply current into an
HDMI device that is powered down.
Typically, the DDC lines and the CEC signals can force significant current back into the
powered-down rails as shown in Figure 26, causing power-on reset problems with the
system, and possible damage. The IP4786CZ32 prevents this backdrive condition
whenever the I/O voltage is greater than the local supply.
supply off
5V
HDMI source
HDMI sink
backdrive current
HDMI ASIC
I2C-bus ASIC
018aaa109
Fig 26. Generalized backdrive protection
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
23 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
11.7 55 mA overcurrent / overvoltage LDO function
The IP4786CZ32 integrates a complete linear output overcurrent protection to isolate
faults from the source power supply, while still meeting HDMI output specifications.
The Low DropOut (LDO) design provides a low-cost solution requiring just a single output
capacitor (1 μF or higher, Equivalent Series Resistance (ESR) < 1 Ω), eliminating start-up
and ripple concerns (see Figure 27).
A typical 100 mV Vdo overcurrent-only solution would require a 5.1 V ±3 % input supply to
guarantee 4.8 V to 5.3 V over 0 mA to 55 mA at the HDMI connector.
The overcurrent / overvoltage feature of the IP4786CZ32 allows the use of wider
tolerance input supplies up to 6.5 V while still meeting the 4.8 V to 5.3 V output limit
required by HDMI. This means, for example, a cost-reduced 5.2 V ±5 % or even
a 5.5 V ±10 % supply can be used with the IP4786CZ32.
As with all the I/O pins, this block is ESD-protected and also provides backdrive protection
in the event that a rogue HDMI sink powers the HDMI cable unexpectedly.
ESD_BYPASS
VCC(5V0)
CEC
3V3
regulator
HDMI_5V0_CON
60 mA
overcurrent
control
DDC/HPD
buffers
CEC
buffer
018aaa110
Fig 27. 5 V LDO with overcurrent / overvoltage protection
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
24 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
11.8 Schematic view of application
Only a single external component (CO = 1 μF) is required to protect and interface the
ASIC to a complete and compliant HDMI port. The 100 nF ESD bypass capacitor is
optional.
CEC
μC
+4.5 V to 6.5 V SUPPLY
CEC_STBY CEC_SYS
11
27
+1.62 V to 5.5 V
SUPPLY
28
29
26
ESD
bypass
(optional)
VDD
100 nF
HDMI
CONNECTOR
TMDS_D2+_SYS
1
24
TMDS_D2+_CON
TMDS_D2–_SYS
2
23
TMDS_D2–_CON
TMDS_D1+_SYS
3
22
TMDS_D1+_CON
TMDS_D1–_SYS
4
21
TMDS_D1–_CON
TMDS_D0+_SYS
5
20
TMDS_D0+_CON
TMDS_D0–_SYS
6
19
TMDS_D0–_CON
TMDS_CK+_SYS
7
18
TMDS_CK+_CON
TMDS_CK–_SYS
8
17
TMDS_CK–_CON
25
CEC_CON
IP4786CZ32
DDC_CLK_SYS
9
15
DDC_CLK_CON
DDC_DAT_SYS
10
14
DDC_DAT_CON
HOTPLUG_DET_SYS
32
12
HOTPLUG_DET_CON
HDMI
ASIC
PAD
HDMI_5V0_CON
13
16
CO
1 μF
UTILITY_CON
018aaa111
Fig 28. Schematic view of IP4786CZ32 application
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
25 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
11.9 Typical application
The IP4786CZ32 is designed to simplify routing to the HDMI connector, and ease the
incorporation of high-level ESD protection into delicately balanced high-speed
TMDS lines. These lines rely on tightly controlled microstrip or stripline transmission lines
with minimal impedance discontinuities, which can deteriorate return loss, increase
deterministic jitter and generally erode overall link signal integrity.
Normally when designing the PCB with standard shunt ESD clamps, careful consideration
must be given to manual pre-compensation of the additional load of the added
ESD component. With the IP4786CZ32 TLCs, the ESD suppressor is designed to
maintain the characteristic impedance of the PCB microstrip or stripline, and therefore the
designer needs only be concerned with the standard-controlled impedance of the
unloaded PCB lines. This simplifies the task of the PCB designer, and minimizes the
tuning cycles, which are sometimes required when pre-compensation misses the mark.
A basic application diagram for the ESD protection of an HDMI interface is shown in
Figure 29 and Figure 30 for type-A and type-D HDMI connector versions.
The optimized HVQFN32 pinning simplifies the PCB design to keep the ESD protection
close to the connector where it can minimize the coupling of the ESD pulse onto other
lines in the system during a strike.
Due to the integrated pull-up and pull-down resistors, only two external capacitors are
required to implement a fully compliant HDMI port.
001aan367
Fig 29. Application of the IP4786CZ32 showing optimized single-layer HDMI type-A
connector routing
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
26 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
001aan368
Fig 30. Application of the IP4786CZ32 showing optimized HDMI type-D connector routing
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
27 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
12. Package outline
HVQFN32: plastic thermal enhanced very thin quad flat package; no leads;
32 terminals; body 5 x 5 x 1 mm
D
B
SOT617-3
A
terminal 1
index area
A
A1
E
detail X
C
e1
e
9
y1 C
C A B
C
v
w
1/2 e b
y
16
L
17
8
e
e2
Eh
1/2 e
24
1
terminal 1
index area
32
25
X
Dh
0
2.5
scale
Dimensions
Unit(1)
mm
max
nom
min
5 mm
A(1)
A1
b
c
0.05 0.30
1
D(1)
Dh
E(1)
Eh
5.1
3.75
5.1
3.75
4.9
3.45
4.9
3.45
0.2
0.00 0.18
e
e1
e2
L
v
w
y
y1
0.5
0.5
3.5
3.5
0.1
0.05 0.05
0.1
0.3
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
Outline
version
SOT617-3
References
IEC
JEDEC
JEITA
sot617-3_po
European
projection
Issue date
02-10-22
11-03-28
MO-220
Fig 31. Package outline SOT617-3 (HVQFN32)
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
28 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
13. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
13.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
13.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
•
•
•
•
•
•
Board specifications, including the board finish, solder masks and vias
Package footprints, including solder thieves and orientation
The moisture sensitivity level of the packages
Package placement
Inspection and repair
Lead-free soldering versus SnPb soldering
13.3 Wave soldering
Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
29 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
13.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 32) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 11 and 12
Table 11.
SnPb eutectic process (from J-STD-020C)
Package thickness (mm)
Package reflow temperature (°C)
Volume (mm3)
< 350
≥ 350
< 2.5
235
220
≥ 2.5
220
220
Table 12.
Lead-free process (from J-STD-020C)
Package thickness (mm)
Package reflow temperature (°C)
Volume (mm3)
< 350
350 to 2000
> 2000
< 1.6
260
260
260
1.6 to 2.5
260
250
245
> 2.5
250
245
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 32.
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
30 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
temperature
maximum peak temperature
= MSL limit, damage level
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 32. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
14. Glossary
HDMI sink — Device which receives HDMI signals e.g. a TV set.
HDMI source — Device which transmit HDMI signal e.g. DVD player.
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
31 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
15. Revision history
Table 13.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
IP4786CZ32 v.1
20110415
Product data sheet
-
-
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
32 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
16.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
16.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
33 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
16.4 Licenses
Purchase of NXP ICs with HDMI technology
Use of an NXP IC with HDMI technology in equipment that complies with
the HDMI standard requires a license from HDMI Licensing LLC, 1060 E.
Arques Avenue Suite 100, Sunnyvale CA 94085, USA, e-mail:
[email protected].
16.5 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
IP4786CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 15 April 2011
© NXP B.V. 2011. All rights reserved.
34 of 35
IP4786CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
18. Contents
1
2
3
4
5
6
6.1
6.2
7
8
9
10
10.1
10.2
11
11.1
11.2
11.3
11.4
11.5
11.6
11.7
11.8
11.9
12
13
13.1
13.2
13.3
13.4
14
15
16
16.1
16.2
16.3
16.4
16.5
17
18
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3
Pinning information . . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6
Static characteristics. . . . . . . . . . . . . . . . . . . . . 7
Dynamic characteristics . . . . . . . . . . . . . . . . . 12
AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . 17
DDC propagation delay . . . . . . . . . . . . . . . . . 17
DDC transition time . . . . . . . . . . . . . . . . . . . . 18
Application information. . . . . . . . . . . . . . . . . . 19
TMDS ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DDC circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Logic low I2C voltage shifter . . . . . . . . . . . . . . 21
Hot plug detect circuit and HEAC support . . . 22
CEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Backdrive protection . . . . . . . . . . . . . . . . . . . . 23
55 mA overcurrent / overvoltage LDO function 24
Schematic view of application . . . . . . . . . . . . 25
Typical application . . . . . . . . . . . . . . . . . . . . . 26
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 28
Soldering of SMD packages . . . . . . . . . . . . . . 29
Introduction to soldering . . . . . . . . . . . . . . . . . 29
Wave and reflow soldering . . . . . . . . . . . . . . . 29
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 29
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 30
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 32
Legal information. . . . . . . . . . . . . . . . . . . . . . . 33
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 33
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Contact information. . . . . . . . . . . . . . . . . . . . . 34
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 15 April 2011
Document identifier: IP4786CZ32
Similar pages