LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
D Single-Supply Operation:
D
D
D
D
D
D
D
DW PACKAGE
(TOP VIEW)
Input Voltage Range Extends to Ground,
and Output Swings to Ground While
Sinking Current
Input Offset Voltage 300 µV Max at 25°C for
LT1014
Offset Voltage Temperature Coefficient
2.5 µV/°C Max for LT1014
Input Offset Current 1.5 nA Max at 25°C for
LT1014
High Gain 1.2 V/µV Min (RL = 2 kΩ), 0.5 V/µV
Min (RL = 600 Ω) for LT1014
Low Supply Current 2.2 mA Max at 25°C for
LT 1014
Low Peak-to-Peak Noise Voltage
0.55 µV Typ
Low Current Noise 0.07 pA/√Hz Typ
1OUT
1IN−
1IN+
VCC+
2IN+
2IN−
2OUT
NC
1OUT
1IN−
1IN+
VCC+
2IN+
2IN−
2OUT
The LT1014, LT1014A, and LT1014D are quad
precision operational amplifiers with 14-pin
industry-standard configuration. They feature low
offset-voltage temperature coefficient, high gain,
low supply current, and low noise.
2
15
3
14
4
13
5
12
6
11
7
10
8
9
4OUT
4IN−
4IN+
VCC−/GND
3IN+
3IN−
3OUT
NC
1
14
2
13
3
12
4
11
5
10
6
9
7
8
4OUT
4IN−
4IN+
VCC−
3IN+
3IN−
3OUT
1IN−
1OUT
NC
4OUT
4IN−
FK PACKAGE
(TOP VIEW)
1IN+
NC
VCC+
NC
2IN+
4
3
2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
4IN+
NC
VCC−/GND
NC
3IN+
2IN−
2OUT
NC
3OUT
3IN−
The LT1014C and LT1014D are characterized for
operation from 0°C to 70°C. The LT1014I and
LT1014DI are characterized for operation from
−40°C to 105°C. The LT1014M, LT1014AM and
LT1014DM are characterized for operation over
the full military temperature range of −55°C to
125°C.
16
J OR N PACKAGE
(TOP VIEW)
description
The LT1014, LT1014A, and LT1014D can be
operated with both dual ±15-V and single 5-V
power supplies. The common-mode input voltage
range includes ground, and the output voltage can
also swing to within a few milivolts of ground.
Crossover distortion is eliminated.
1
NC − No internal connection
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2009, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
AVAILABLE OPTIONS{
PACKAGED DEVICES}
VIO max
AT 25°C
SMALL
OUTLINE
(DW)§
CHIP
CARRIER
(FK)
CERAMIC
DIP
(J)
PLASTIC
DIP
(N)
0°C to 70°C
300 µV
800 µV
—
LT1014DDW
—
—
—
—
LT1014CN
LT1014DN
−40°C
40°C to 105°C
300 µV
800 µV
—
LT1014DIDW
—
—
—
—
LT1014IN
LT1014DIN
−55°C
55 C to 125
125°C
C
180 µV
300 µV
800 µV
—
—
LT1014DMDW
LT1014AMFK
LT1014MFK
—
LT1014AMJ
LT1014MJ
—
—
LT1014MN
LT1014DMN
TA
†
For the most current package and ordering information, see the Package Option Addendum at the end
of this document, or see the TI web site at www.ti.com.
‡ Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
§ The DW package is available taped and reeled. Add the suffix R to the device type
(e.g., LT1014DDWR).
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
400 Ω
400 Ω
Q21
Q1
Q5
Q22
Q2
9 kΩ
Q6
Q12
75 pF
Q28
Q27
9 kΩ
Component values are nominal.
VCC−
IN+
IN−
V CC+
Q9
Q11
Q13
5 kΩ
Q7
Q8
5 kΩ
Q29
Q4
1.6 kΩ
Q16
Q3
1.6 kΩ
Q10
10 pF
3.9 kΩ
Q14
1.6 kΩ
2 kΩ
Q19
2.5 pF
Q17
Q18
21 pF
Q15
1.3 kΩ
Q20
Q32
100 Ω
Q25
Q23
Q31
Q26
2 kΩ
10 pF
2 kΩ
4 pF
2.4 kΩ
Q30
1 kΩ
Q24
Q34
18 Ω
Q33
14 kΩ
30 Ω
42 kΩ
OUT
Q35
Q40
Q37
Q38
J1
600 Ω
Q39
Q41
Q36
800 Ω
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
schematic (each amplifier)
3
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage (see Note 1): VCC+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 V
VCC− . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −22 V
Differential input voltage (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±30 V
Input voltage range, VI (any input) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC− − 5 V to VCC+
Duration of short-circuit current at (or below) TA = 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: LT1014C, LT1014D . . . . . . . . . . . . . . . . . . . . . . . . . . . −0°C to 70°C
LT1014I, LT1014DI . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 105°C
LT1014M, LT1014AM, LT1014DM . . . . . . . . . . . . . −55°C to 125°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC−.
2. Differential voltages are at the noninverting input with respect to the inverting input.
3. The output may be shorted to either supply.
DISSIPATION RATING TABLE
4
PACKAGE
TA ≤ 25°C
POWER RATING
DW
1025 mV
8.2 mW/°C
656 mW
369 mW
205 mW
FK
1375 mV
11.0 mW/°C
880 mW
495 mW
275 mW
J
1375 mV
11.0 mW/°C
880 mW
495 mW
275 mW
N
1150 mV
9.2 mW/°C
736 mW
414 mW
230 mW
DERATING FACTOR
ABOVE TA = 25°C
POST OFFICE BOX 655303
TA = 70°C
POWER RATING
• DALLAS, TEXAS 75265
TA = 105°C
POWER RATING
TA = 125°C
POWER RATING
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
electrical characteristics at specified free-air temperature, VCC± = ±15 V, VIC = 0 (unless otherwise
noted)
PARAMETER
VIO
Input offset voltage
aV
Temperature coeficient
of input offset voltage
IO
LT1014C
TEST CONDITIONS
TA†
Input offset current
IIB
Input bias current
MAX
60
300
Full range
Full range
0.4
25°C
0.5
25°C
0.15
Full range
†
‡
VOM
Maximum peak output
voltage swing
AVD
Large-signal
L
i
l diff
differential
ti l
voltage amplification
RL = 2 kΩ
VO = ±10 V,
VO = ±10 V
V,
−12
−15
to
13.5
Full range
−15
to 13
25°C
±12.5
Common mode
Common-mode
rejection ratio
kSVR
Supply-voltage
rejection ratio
(∆VCC/∆VIO)
VCC± = ±2 V to ±18 V
Channel separation
VO = ±10 V,
VIC = −15 V to 13 V
MAX
800
1000
2.5
0.7
5
1.5
0.15
−12
−15.3
to
13.8
µV/°C
nA
−30
−38
−15
to
13.5
µV
V
1.5
2.8
−30
UNIT
µV/mo
0.5
−15.3
to
13.8
nA
V
−15
to 13
±14
±12.5
±14
Full range
±12
25°C
0.5
2
0.5
2
25°C
1.2
8
1.2
8
Full range
0.7
25°C
97
Full range
94
25°C
100
Full range
97
VIC = −15 V to 13.5 V
CMRR
200
−38
25°C
RL = 600 Ω
RL = 2 kΩ
TYP‡
2.8
Full range
Common-mode
input voltage range
MIN
550
25°C
VICR
LT1014D
TYP‡
25°C
RS = 50 Ω
Long-term drift
of input offset voltage
IIO
MIN
V
±12
V/µV
0.7
117
97
117
dB
94
117
100
117
dB
RL = 2 kΩ
97
25°C
120
137
120
137
dB
rid
Differential
input resistance
25°C
70
300
70
300
MΩ
ric
Common-mode
input resistance
25°C
4
4
GΩ
ICC
Supply current
per amplifier
25°C
0.35
Full range
0.55
0.6
0.35
0.55
0.6
mA
Full range is 0°C to 70°C.
All typical values are at TA = 25°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
electrical characteristics at specified free-air temperature, VCC± = 5 V, VCC− = 0, VO = 1.4 V, VIC = 0
(unless otherwise noted)
PARAMETER
VIO
Input offset voltage
IIO
Input offset current
IIB
Input bias current
VICR
Common-mode
input voltage range
TA†
TEST CONDITIONS
LT1014C
MIN
MAX
90
450
25°C
RS = 50 Ω
Full range
0.2
25°C
Output low,
RL = 600 Ω to GND
M i
t t
Maximum
peakk output
voltage swing
AVD
Large-signal differential
voltage amplification
ICC
Supply current
per amplifier
0.2
−50
−15
0
to 3.5
Full range
0 to 3
−0.3
to 3.8
nA
−50
−90
0
to 3.5
µV
V
2
6
−90
25°C
950
UNIT
−0.3
to 3.8
nA
V
0 to 3
25°C
15
25
15
25
25°C
5
10
5
10
Full range
13
Isink = 1 mA
25°C
No load
25°C
4
4.4
4
4.4
25°C
3.4
4
3.4
4
V
Full range
3.2
220
350
1
V/µV
3.2
25°C
1
25°C
0.3
Full range
350
mV
Output low,
VO = 5 mV to 4 V,
RL = 500 Ω
220
13
Output high,
Output high,
RL = 600 Ω to GND
†
−15
MAX
1200
6
Full range
No load
TYP
250
2
Full range
Output low,
MIN
570
25°C
VOM
LT1014D
TYP
0.5
0.3
0.55
0.5
0.55
mA
Full range is 0°C to 70°C.
operating characteristics, VCC± = ±15 V, VIC = 0, TA = 25°C
PARAMETER
SR
6
TEST CONDITIONS
Slew rate
MIN
TYP
0.2
0.4
f = 10 Hz
24
f = 1 kHz
22
MAX
UNIT
V/µs
Vn
Equivalent input noise voltage
VN(PP)
Peak-to-peak equivalent input noise voltage
f = 0.1 Hz to 10 Hz
0.55
µV
In
Equivalent input noise current
f = 10 Hz
0.07
pA/√Hz
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
electrical characteristics at specified free-air temperature, VCC± = ±15 V, VIC = 0 (unless otherwise
noted)
PARAMETER
VIO
Input offset voltage
aV
Temperature coeficient
of input offset voltage
IO
LT1014I
TEST CONDITIONS
TA†
Input offset current
IIB
Input bias current
MAX
60
300
Full range
Full range
0.4
25°C
0.5
25°C
0.15
Full range
†
‡
VOM
Maximum peak
output voltage swing
AVD
Large-signal
L
i
l diff
differential
ti l
voltage amplification
RL = 2 kΩ
VO = ±10 V,
VO = ±10 V
V,
−12
CMRR
Common mode
Common-mode
rejection ratio
15 V to 13
13.5
5V
VIC = −15
kSVR
Supply-voltage
rejection ratio
(∆VCC/∆VIO)
VCC± = ±2 V to ±18 V
Channel separation
VO = ±10 V,
200
−15
to
13.5
Full range
−15
to 13
25°C
±12.5
MAX
800
1000
2.5
0.7
5
1.5
0.15
−12
−15.3
to
13.8
µV/°C
nA
−30
−38
−15
to
13.5
µV
V
1.5
2.8
−30
UNIT
µV/mo
0.5
−38
25°C
−15.3
to
13.8
nA
V
−15
to 13
±14
±12.5
±14
Full range
±12
25°C
0.5
2
0.5
2
25°C
1.2
8
1.2
8
Full range
0.7
25°C
97
Full range
94
25°C
100
Full range
97
RL = 600 Ω
RL = 2 kΩ
TYP‡
2.8
Full range
Common-mode
input voltage range
MIN
550
25°C
VICR
LT1014DI
TYP‡
25°C
RS = 50 Ω
Long-term drift
of input offset voltage
IIO
MIN
V
±12
V/µV
0.7
117
97
117
dB
94
117
100
117
dB
RL = 2 kΩ
97
25°C
120
137
120
137
dB
rid
Differential
input resistance
25°C
70
300
70
300
MΩ
ric
Common-mode
input resistance
25°C
4
4
GΩ
ICC
Supply current
per amplifier
25°C
0.35
Full range
0.55
0.6
0.35
0.55
0.6
mA
Full range is −40°C to 105°C.
All typical values are at TA = 25°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
electrical characteristics at specified free-air temperature, VCC+ = 5 V, VCC− = 0, VO = 1.4 V, VIC = 0
(unless otherwise noted)
PARAMETER
VIO
Input offset voltage
IIO
Input offset current
IIB
Input bias current
VICR
Common-mode
input voltage range
LT1014I
TEST CONDITIONS
TA†
MIN
MAX
90
450
25°C
RS = 50 Ω
Full range
0.2
Full range
Output low,
RL = 600 Ω to GND
M i
k
Maximum
peak
output voltage swing
AVD
Large-signal differential
voltage amplification
ICC
Supply current
per amplifier
0.2
−50
−15
0
to 3.5
Full range
0 to 3
−0.3
to 3.8
nA
−50
−90
0
to 3.5
µV
V
2
6
−90
25°C
950
UNIT
−0.3
to 3.8
nA
V
0 to 3
25°C
15
25
15
25
25°C
5
10
5
10
Full range
13
25°C
Output high,
No load
25°C
4
4.4
4
4.4
25°C
3.4
4
3.4
4
V
Full range
3.2
220
350
1
V/µV
3.2
25°C
1
25°C
0.3
Full range
350
mV
Isink = 1 mA
VO = 5 mV to 4 V,
RL = 500 Ω
220
13
Output low,
Output high,
RL = 600 Ω to GND
†
−15
MAX
1200
6
25°C
No load
TYP
250
2
Full range
Output low,
MIN
570
25°C
VOM
LT1014DI
TYP
0.5
0.3
0.55
0.5
0.55
mA
Full range is −40°C to 105°C.
operating characteristics, VCC+ = ±15 V, VIC = 0, TA = 25°C
PARAMETER
8
TEST CONDITIONS
MIN
TYP
0.2
0.4
MAX
UNIT
SR
Slew rate
Vn
Equivalent input noise voltage
VN(PP)
Peak-to-peak equivalent input noise voltage
f = 0.1 Hz to 10 Hz
0.55
µV
In
Equivalent input noise current
f = 10 Hz
0.07
pA/√Hz
POST OFFICE BOX 655303
f = 10 Hz
24
f = 1 kHz
22
• DALLAS, TEXAS 75265
V/µs
nV/√H
nV/√Hz
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
electrical characteristics at specified free-air temperature, VCC± = ±15 V, VIC = 0 (unless otherwise
noted)
PARAMETER
VIO
Input offset
voltage
aV
Temperature
coefficient of
input offset
voltage
IO
TEST
CONDITIONS
RS = 50 Ω
Long-term drift
of input offset
voltage
IIO
Input offset
current
IIB
Input bias
current
VICR
Common-mode
input voltage
range
VOM
Maximum peak
output voltage
swing
AVD
Large-signal
differential
voltage
amplification
CMRR
kSVR
†
‡
Common mode
Common-mode
rejection ratio
TA†
LT1014M
MIN
MAX
60
300
25°C
Full range
Full range
0.5
25°C
0.5
25°C
0.15
−12
Full range
VO = ±10 V,
RL = 2 kΩ
MAX
60
180
−15
to
13.5
Full range
−14.9
to 13
25°C
±12.5
Full range
±11.5
MIN
2.5
200
0.5
1.5
0.15
2
0.5
−12
0.8
±13
2.5
−12
−15.3
to
13.8
µV
V
µV/°C
1.5
nA
−30
−45
−15
to
13.5
UNIT
µV/mo
5
−20
−14.9
to 13
±14
0.15
−30
−15
to
13.5
800
0.5
2.8
−30
MAX
1000
0.5
−15.3
to
13.8
TYP‡
350
−45
25°C
LT1014DM
TYP‡
5
25°C
VO = ±10 V,
RL = 600 Ω
MIN
550
Full range
RL = 2 kΩ
LT1014AM
TYP‡
−15.3
to
13.8
nA
V
−14.9
to 13
±14
±12.5
±12
±14
V
±11.5
25°C
0.5
2
0.8
2.2
0.5
2
25°C
1.2
8
1.5
8
1.2
8
Full range
0.25
0.4
V/ V
V/µV
0.25
VIC = −15 V to
13.5 V
25°C
97
VIC = −14.9 V
to 13 V
Full range
94
25°C
100
Full range
97
25°C
120
137
123
137
120
137
dB
70
300
100
300
70
300
MΩ
4
GΩ
Supply-voltage
rejection ratio
(∆VCC/∆VIO)
VCC± = ±2 V to
±18 V
Channel
separation
VO = ±10 V,
RL = 2 kΩ
117
100
117
97
117
dB
96
117
103
94
117
100
117
dB
100
rid
Differential input
resistance
25°C
ric
Common-mode
input resistance
25°C
4
ICC
Supply current
per amplifier
25°C
0.35
Full range
97
4
0.55
0.7
0.35
0.50
0.6
0.35
0.55
0.7
mA
Full range is −55°C to 125°C.
All typical values are at TA = 25°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
electrical characteristics at specified free-air temperature, VCC+ = 5 V, VCC− = 0, VO = 1.4 V, VIC = 0
(unless otherwise noted)
PARAMETER
VIO
Input
offset voltage
IIO
Input
offset current
IIB
Input
bias current
VICR
Commonmode input
voltage range
TEST
CONDITIONS
RS = 50Ω
TA†
†
AVD
Large-signal
differential
voltage
amplification
ICC
Supply current
per amplifier
LT1014AM
MAX
MIN
LT1014DM
TYP
MAX
MIN
TYP
MAX
25°C
90
450
90
280
250
950
400
1500
400
960
800
2000
125°C
200
750
200
480
560
1200
25°C
0.2
2
0.2
1.3
0.2
2
−15
−50
−15
−35
−15
−50
RS = 50Ω,
VIC = 0.1 V
Full range
10
25°C
Full range
25°C
Full range
Output low,
RL = 600Ω to
GND
Maximum
peak output
voltage swing
TYP
Full range
Output low,
No load
VOM
LT1014M
MIN
7
−120
0
to 3.5
0
to 3.5
0.1
to 3
−0.3
to 3.8
nA
−120
0
to 3.5
0.1
to 3
µV
10
−90
−0.3
to 3.8
UNIT
−0.3
to 3.8
V
0.1
to 3
25°C
15
25
15
25
15
25
25°C
5
10
5
10
5
10
mV
Full range
18
15
18
Output low,
Isink = 1 mA
25°C
Output high,
No load
25°C
4
4.4
4
4.4
4
4.4
Output high,
25°C
3.4
4
3.4
4
3.4
4
V
RL = 600Ω to
GND
Full range
3.1
1
V/µV
VO = 5 mV to 4 V,
RL = 500Ω
220
220
350
3.2
25°C
1
25°C
0.3
Full range
350
220
3.1
1
0.5
350
0.3
0.65
0.45
0.3
0.55
0.5
0.65
mA
Full range is −55°C to 125°C.
operating characteristics, VCC± = ±15 V, VIC = 0, TA = 25°C
PARAMETER
SR
TEST CONDITIONS
Slew rate
MIN
TYP
0.2
0.4
f = 10 Hz
24
f = 1 kHz
22
MAX
UNIT
V/µs
Vn
Equivalent input noise voltage
VN(PP)
Peak-to-peak equivalent input noise voltage
f = 0.1 Hz to 10 Hz
0.55
µV
In
Equivalent input noise current
f = 10 Hz
0.07
pA/√Hz
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√H
nV/√Hz
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
Input offset voltage vs Balanced source resistance
1
VIO
Input offset voltage vs Free-air temperature
2
∆VIO
Warm-Up Change in input offset voltage vs Elapsed time
3
IIO
Input offset current vs Free-air temperature
4
IIB
Input bias current vs Free-air temperature
5
VIC
Common-mode input voltage vs Input bias current
AVD
Differential voltage amplification
6
vs Load resistance
7, 8
vs Frequency
9, 10
Channel separation vs Frequency
11
Output saturation voltage vs Free-air temperature
12
CMRR
Common-mode rejection ratio vs Frequency
13
kSVR
Supply-voltage rejection ratio vs Frequency
14
ICC
Supply current vs Free-air temperature
15
IOS
Short-circuit output current vs Elapsed time
16
Vn
Equivalent input noise voltage vs Frequency
17
In
Equivalent input noise current vs Frequency
17
VN(PP)
Peak-to-peak input noise voltage vs Time
18
Pulse response (small signal) vs Time
19, 21
Pulse response (large signal) vs Time
20, 22, 23
Phase shift vs Frequency
POST OFFICE BOX 655303
9
• DALLAS, TEXAS 75265
11
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
TYPICAL CHARACTERISTICS†
INPUT OFFSET VOLTAGE
OF REPRESENTATIVE UNITS
vs
FREE-AIR TEMPERATURE
LT1014
INPUT OFFSET VOLTAGE
vs
BALANCED SOURCE RESISTANCE
250
10
1
VCC± = 5 V
VCC− = 0
0.1
RS
VCC± = ±15 V
0.01
1k
−
+
150
100
50
0
−50
−100
−150
−200
RS
3k
VCC± = ±15 V
200
VIO − Input Offset Voltage − µ V
VIO − Input Offset Voltage − mV
TA = 25°C
10 k 30 k 100 k 300 k 1 M
−250
−50
3 M 10 M
−25
0
Rs − Source Resistance − Ω
Figure 1
I IO − Input Offset Current − nA
∆V IO − Change in Input Offset Votlage − µ V
N Package
1
0.8
0.6
VCC± = ±2.5 V
0.4
VCC+ = 5 V, VCC− = 0
0.2
J Package
2
3
4
VCC± = ±15 V
5
0
−50
−25
Figure 3
12
0
25
50
75
100
TA − Free-Air Temperature − °C
t − Time After Power-On − min
†
125
VIC = 0
2
1
100
1
3
0
75
INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
VCC± = ±15 V
TA = 25°C
4
0
50
Figure 2
WARM-UP CHANGE IN INPUT OFFSET VOLTAGE
vs
ELAPSED TIME
5
25
TA − Free-Air Temperature − °C
Figure 4
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
125
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
TYPICAL CHARACTERISTICS†
COMMON-MODE INPUT VOLTAGE
vs
INPUT BIAS CURRENT
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
−30
5
15
VIC = 0
I IB − Input Bias Current − nA
−25
−20
VCC+ = 5 V, VCC− = 0
−15
VCC± = ±2.5 V
−10
VCC± = ±15 V
−5
0
−50
10
4
5
3
VCC± = ±15 V
(Left Scale)
1
−10
0
−15
−25
0
25
50
75
100
0
125
−5
−10
−25
−1
−30
VCC± = ±15 V
VO = ±10 V
TA = 25°C
TA = −55°C
1
TA = 125°C
0.4
1k
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
LOAD RESISTANCE
A VD − Differential Voltage Amplivication − V/µ V
A VD − Differential Voltage Amplivication − V/µ V
10
400
−20
Figure 6
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
LOAD RESISTANCE
4
−15
IIB − Input Bias Current − nA
Figure 5
4k
10 k
10
VCC+ = 5 V, VCC− = 0
VO = 20 mV to 3.5 V
4
TA = −55°C
1
TA = 25°C
TA = 125°C
0.4
0.1
100
RL − Load Resistance − Ω
400
1k
4k
10 k
RL − Load Resistance − Ω
Figure 7
†
2
−5
TA − Free-Air Temperature − °C
0.1
100
VCC+ = 5 V
VCC− = 0
(Right Scale)
0
VIC − Common-Mode Input Voltage − V
VIC − Common-Mode Input Voltage − V
TA = 25°C
Figure 8
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
TYPICAL CHARACTERISTICS†
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREQUENCY
VCC± = ±15 V
100°
120°
AVD
VCC+ = 5 V
VCC− = 0
10
140°
160°
VCC+ = 5 V
VCC− = 0
0
180°
200°
VCC± = ±15 V
220°
−10
0.01
0.3
1
A VD − Differential Voltage Amplivication − dB
20
140
80°
VIC = 0
CL = 100 pF
TA = 25°C
φ − Phase Shift
A VD − Differential Voltage Amplivication − dB
DIFFERENTIAL VOLTAGE AMPLIFICATION
AND PHASE SHIFT
vs
FREQUENCY
120
100
VCC + = 5 V
VCC − = 0
80
40
20
0
1
10
Figure 9
OUTPUT SATURATION VOLTAGE
vs
FREE-AIR TEMPERATURE
Limited by
Thermal
Interaction
VCC+ = 5 V to 30 V
VCC− = 0
Output Saturation Voltage − V
Channel Separation − dB
10
VCC± = ±15 V
VI(PP) = 20 V to 5 kHz
RL = 2 kΩ
TA = 25°C
120
RL = 100 Ω
RL = 1 kΩ
100
Limited by
Pin-to-Pin
Capacitance
80
1 k 10 k 100 k 1 M 10 M
Figure 10
CHANNEL SEPARATION
vs
FREQUENCY
140
100
f − Frequency − Hz
f − Frequency − MHz
160
VCC± = ±15 V
60
−20
0.01 0.1
240°
10
3
CL = 100 pF
TA = 25°C
Isink = 10 mA
1
Isink = 5 mA
Isink = 1 mA
0.1
Isink = 100 µA
Isink = 10 µA
Isink = 0
60
10
100
1k
100 k
10 k
1M
0.01
−50
−25
f − Frequency − Hz
Figure 11
†
14
0
25
50
75
100
TA − Free-Air Temperature − °C
Figure 12
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
125
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
TYPICAL CHARACTERISTICS†
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
140
TA = 25°C
K SVR − Supply-Voltage Rejection Ratio − dB
CMRR − Common-Mode Rejection Ratio − dB
120
100
VCC± = ±15 V
VCC+ = 5 V
VCC− = 0
80
60
40
20
0
10
100
1k
100 k
10 k
120
100
Positive
Supply
Negative
Supply
80
60
40
20
0
0.1
1M
VCC± = ± 15 V
TA = 25°C
1
f − Frequency − Hz
I OS − Short-Circuit Output Current − mA
I CC − Supply Current Per Amplifier −µ A
40
420
380
VCC± = ±15 V
340
VCC+ = 5 V
VCC− = 0
0
25
100 k
1M
50
75
100
125
VCC± = ±15 V
TA = −55°C
30
TA = 25°C
20
TA = 125°C
10
0
−10
−20
−30
−40
0
TA − Free-Air Temperature − °C
TA = 125°C
TA = 25°C
TA = −55°C
1
2
3
t − Time − min
Figure 15
†
10 k
SHORT-CIRCUIT OUTPUT CURRENT
vs
ELAPSED TIME
460
−25
1k
Figure 14
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
260
−50
100
f − Frequency − Hz
Figure 13
300
10
Figure 16
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
TYPICAL CHARACTERISTICS
PEAK-TO-PEAK INPUT NOISE VOLTAGE
OVER A 10-SECOND PERIOD
vs
TIME
1000
300
300
In
100
100
Vn
30
30
1/f Corner = 2 Hz
10
1
VCC± = ±2 V to ±18 V
f = 0.1 Hz to 10 Hz
TA = 25°C
1600
1200
800
400
0
10
1k
100
10
2000
V N(PP) − Noise Voltage − nV
VCC± = ±2 V to ±18 V
TA = 25°C
I n − Equivalent Input Noise Current −fA/ Hz
Vn − Equivalent Input Noise Voltage − fA/ Hz
1000
EQUIVALENT INPUT NOISE VOLTAGE
AND EQUIVALENT INPUT NOISE CURRENT
vs
FREQUENCY
0
2
4
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
vs
TIME
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE
vs
TIME
6
VCC± = ±15 V
AV = 1
TA = 25°C
5
40
V O − Output Voltage − V
V O − Output Voltage − mV
60
20
0
−20
4
2
1
0
−60
−1
0
2
4
6
8
10
12
14
VCC+ = 5 V
VCC− = 0
VI = 0 to 4 V
RL = 0
AV = 1
TA = 25°C
3
−40
−80
−2
t − Time − µs
0
10
20
30
t − Time − µs
Figure 19
16
10
Figure 18
Figure 17
80
8
6
t − Time − s
f − Frequency − Hz
Figure 20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
40
50
60
70
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
TYPICAL CHARACTERISTICS
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE
vs
TIME
160
6
VCC+ = 5 V
VCC− = 0
VI = 0 to 100 mV
RL = 600 Ω to GND
AV = 1
TA = 25°C
120
100
5
4
V O − Output Voltage − mV
140
80
60
40
2
1
0
0
−1
−20
0
20
40
60
80
VCC+ = 5 V
VCC− = 0
VI = 0 to 4 V
RL = 4.7 kΩ to 5 V
AV = 1
TA = 25°C
3
20
−2
100 120 140
10 20 30 40
t − Time − µs
0
t − Time − µs
Figure 21
50
60
70
Figure 22
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
vs
TIME
6
5
V O − Output Voltage − V
V O − Output Voltage − mV
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
vs
TIME
4
VCC+ = 5 V
VCC− = 0
VI = 0 to 4 V
RL = 0
AV = 1
TA = 25°C
3
2
1
0
−1
−2
0
10
20
30
40
50
60
70
t − Time − µs
Figure 23
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
APPLICATION INFORMATION
single-supply operation
The LT1014 is fully specified for single-supply operation (VCC− = 0). The common-mode input voltage range
includes ground, and the output swings within a few millivolts of ground.
Furthermore, the LT1014 has specific circuitry that addresses the difficulties of single-supply operation, both
at the input and at the output. At the input, the driving signal can fall below 0 V, either inadvertently or on a
transient basis. If the input is more than a few hundred millivolts below ground, the LT1014 is designed to deal
with the following two problems that can occur:
1. On many other operational amplifiers, when the input is more than a diode drop below ground, unlimited
current flows from the substrate (VCC− terminal) to the input, which can destroy the unit. On the LT1014,
the 400-Ω resistors in series with the input (see schematic) protect the device even when the input is 5 V
below ground.
2. When the input is more than 400 mV below ground (at TA = 25°C), the input stage of similar type operational
amplifiers saturates, and phase reversal occurs at the output. This can cause lockup in servo systems.
Because of unique phase-reversal protection circuitry (Q21, Q22, Q27, and Q28), the LT1014 outputs do
not reverse, even when the inputs are at −1.5 V (see Figure 24).
However, this phase-reversal protection circuitry does not function when the other operational amplifier on the
LT1014 is driven hard into negative saturation at the output. Phase-reversal protection does not work on an
amplifier:
D
D
D
D
When 4’s output is in negative saturation (the outputs of 2 and 3 have no effect)
When 3’s output is in negative saturation (the outputs of 1 and 4 have no effect)
When 2’s output is in negative saturation (the outputs of 1 and 4 have no effect)
When 1’s output is in negative saturation (the outputs of 2 and 3 have no effect)
At the output, other single-supply designs either cannot swing to within 600 mV of ground or cannot sink more
than a few microproamperes while swinging to ground. The all-npn output stage of the LT1014 maintains its low
output resistance and high gain characteristics until the output is saturated. In dual-supply operations, the output
stage is free of crossover distortion.
4
3
2
1
0
−1
−2
5
V O − Output Voltage − V
5
V O − Output Voltage − V
V I(PP) − Input Voltage − V
5
4
3
2
1
0
−1
(a) VI(PP) = −1.5 V to 4.5 V
4
3
2
1
0
−1
(b) Output Phase Reversal
Exhibited by LM358
(c) No Phase Reversal
Exhibited by LT1014
Figure 24. Voltage-Follower Response
With Input Exceeding the Negative Common-Mode Input Voltage Range
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
APPLICATION INFORMATION
comparator applications
The single-supply operation of the LT1014 can be used as a precision comparator with TTL-compatible output.
In systems using both operational amplifiers and comparators, the LT1014 can perform multiple duties (see
Figures 25 and 26).
5
4
10 mV
5 mV
2 mV
3
2
Overdrive
1
V O − Output Voltage − V
V O − Output Voltage − V
5
VCC+ = 5 V
VCC− = 0
TA = 25°C
4
3
2
10 mV
5 mV
2 mV
1
Overdrive
0
100 mV
0
VCC+ = 5 V
VCC− = 0
TA = 25°C
50 100 150 200 250 300 350 400 450
Differential
Input Voltage
Differential
Input Voltage
0
100 mV
0
50 100 150 200 250 300 350 400 450
t − Time − µs
t − Time − µs
Figure 25. Low-to-High-Level Output Response
for Various Input Overdrives
Figure 26. High-to-Low-Level Output Response
for Various Input Overdrives
low-supply operation
The minimum supply voltage for proper operation of the LT1014 is 3.4 V (three Ni-Cad batteries). Typical supply
current at this voltage is 290 µA; therefore, power dissipation is only 1 mW per amplifier.
offset voltage and noise testing
Figure 30 shows the test circuit for measuring input offset voltage and its temperature coefficient. This circuit
with supply voltages increased to ±20 V is also used as the burn-in configuration.
The peak-to-peak equivalent input noise voltage of the LT1014 is measured using the test circuit shown in
Figure 27. The frequency response of the noise tester indicates that the 0.1-Hz corner is defined by only one
zero. The test time to measure 0.1-Hz to 10-Hz noise should not exceed 10 seconds, as this time limit acts as
an additional zero to eliminate noise contribution from the frequency band below 0.1 Hz.
An input noise-voltage test is recommended when measuring the noise of a large number of units. A 10-Hz input
noise-voltage measurement correlates well with a 0.1-Hz peak-to-peak noise reading because both results are
determined by the white noise and the location of the 1/f corner frequency.
Noise current is measured by the circuit and formula shown in Figure 28. The noise of the source resistors is
subtracted.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
APPLICATION INFORMATION
0.1 µF
100 kΩ
10 Ω
+
2 kΩ
+
LT1014
−
4.7 µF
4.3 kΩ
22 µF
LT1001
2.2 µF
−
AVD = 50,000
Oscilloscope
Rin = 1 MΩ
100 kΩ
110 kΩ
24.3 kΩ
0.1 µF
NOTE A: All capacitor values are for nonpolarized capacitors only.
Figure 27. 0.1-Hz to 10-Hz Peak-to-Peak Noise Test Circuit
10 kΩ
10 Mن
10 Mن
+
100 Ω
10 Mن
†
10 Mن
Vn
LT1014
In +
ƪVno2 * (820 nV)2ƫ
40 MW
−
Metal-film resistor
Figure 28. Noise-Current Test Circuit and Formula
50 Ω
(see Note A)
15 V
100 Ω
(see Note A)
+
LT1014
VO = 1000 VIO
−
50 Ω
(see Note A)
−15 V
NOTE A: Resistors must have low thermoelectric potential.
Figure 29. Test Circuit for VIO and αVIO
20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
100
1ń2
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
APPLICATION INFORMATION
5V
Q3
2N2905
820 Ω
Q1
2N2905
T1‡
10 µF
+
68 Ω
1N4002 (4)
10 µF
+
SN74HC04 (6)
0.002 µF
10 kΩ
10 kΩ
0.33 µF
Q4
2N2222
820 Ω
Q2
2N2905
10 kΩ
100 kΩ
5V
10 Ω†
±
2 kΩ
1/4
LT1014
+
100 pF
5V
10 kن
20-mA
Trim
4 kن
10 kن
1 kΩ
4-mA
Trim
4.3 kΩ
80 Ω†
±
1/4
LT1014
+
100 Ω†
4-mA to 20-mA OUT
To Load
2.2 kΩ Max
LT1004
1.2 V
IN
0 to 4 V
†
‡
1% film resistor. Match 10-kΩ resistors 0.05%.
T1 = PICO-31080
Figure 30. 5-V Powered, 4-mA to 20-mA Current-Loop Transmitter With 12-Bit Accuracy
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
APPLICATION INFORMATION
5V
100 kΩ
1/4
LT1014
+
10 µF
+
+
1/4
LT1014
−
−
To
Inverter
Driver
1N4002 (4)
T1
0.1 Ω
68 kن
4-mA to 20-mA OUT
Fully Floating
10 kن
2 kΩ
4-mA
Trim
LT1004
1.2 V
†
301 Ω†
4 kن
4.3 kΩ
5V
1 kΩ
20-mA
Trim
IN
0 to 4 V
1% film resistor
Figure 31. Fully Floating Modification to 4-mA to 20-mA Current-Loop Transmitter With 8-Bit Accuracy
5V
1/2 LTC1043
IN+
5
6
2
5
6
3
IN−
18
8
1/4
LT1014
1 µF
1 µF
+
−
15
7
4
OUT A
R2
R1
1/2 LTC1043
IN+
8
7
11
IN−
+
1/4
LT1014
1 µF
1 µF
12
13
3
2
−
14
0.01 µF
1
OUT B
R2
R1
NOTE A: VIO = 150 µV, AVD = (R1/R2) + 1, CMRR = 120 dB, VICR = 0 to 5 V
Figure 32. 5-V Single-Supply Dual Instrumentation Amplifier
22
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
APPLICATION INFORMATION
10
200
kن
2
LT1014
20 kΩ
3
−
10 kن
1
10 kن
+
10 kΩ
‡
5V
13
RG (2 kΩ Typ)
12
1 µF
‡
20 kΩ
5
IN+
−
4
14
200 kΩ
6
To Input
Cable Shields
−
‡
IN−
8
LT1014
9
5V
+
LT1014
+
10 kΩ
OUT
11
−
LT1014
7
+
10 kن
10 kن
‡
5V
††
1% film resistor. Match 10-kΩ resistors 0.05%.
‡ For high source impedances, use 2N2222 as diodes (with collector connected to base).
NOTE A: AVD = (400,000/RG) + 1
Figure 33. 5-V Powered Precision Instrumentation Amplifier
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jun-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
5962-89677012A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
596289677012A
LT1014
AMFKB
5962-8967701CA
ACTIVE
CDIP
J
14
1
TBD
A42
N / A for Pkg Type
-55 to 125
5962-8967701CA
LT1014AMJB
5962-89677022A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
596289677022A
LT1014MFKB
5962-8967702CA
ACTIVE
CDIP
J
14
1
TBD
A42
N / A for Pkg Type
-55 to 125
5962-8967702CA
LT1014MJB
LT1014AMFKB
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
596289677012A
LT1014
AMFKB
LT1014AMJ
ACTIVE
CDIP
J
14
1
TBD
A42
N / A for Pkg Type
LT1014AMJ
LT1014AMJB
ACTIVE
CDIP
J
14
1
TBD
A42
N / A for Pkg Type
5962-8967701CA
LT1014AMJB
LT1014CN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
0 to 70
LT1014CN
LT1014CNE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
0 to 70
LT1014CN
LT1014DDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LT1014D
LT1014DDWE4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LT1014D
LT1014DDWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LT1014D
LT1014DDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LT1014D
LT1014DDWRE4
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LT1014D
LT1014DDWRG4
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
LT1014D
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jun-2017
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LT1014DIDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 105
LT1014DI
LT1014DIDWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 105
LT1014DI
LT1014DIDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 105
LT1014DI
LT1014DIN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
-40 to 105
LT1014DIN
LT1014DINE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
-40 to 105
LT1014DIN
LT1014DMDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-55 to 125
LT1014DM
LT1014DMDWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-55 to 125
LT1014DM
LT1014DN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
0 to 70
LT1014DN
LT1014DNE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
0 to 70
LT1014DN
LT1014MFKB
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
596289677022A
LT1014MFKB
LT1014MJ
ACTIVE
CDIP
J
14
1
TBD
A42
N / A for Pkg Type
-55 to 125
LT1014MJ
LT1014MJB
ACTIVE
CDIP
J
14
1
TBD
A42
N / A for Pkg Type
5962-8967702CA
LT1014MJB
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jun-2017
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LT1014D :
• Enhanced Product: LT1014D-EP
NOTE: Qualified Version Definitions:
• Enhanced Product - Supports Defense, Aerospace and Medical Applications
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LT1014DDWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
LT1014DIDWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LT1014DDWR
SOIC
DW
16
2000
367.0
367.0
38.0
LT1014DIDWR
SOIC
DW
16
2000
367.0
367.0
38.0
Pack Materials-Page 2
PACKAGE OUTLINE
J0014A
CDIP - 5.08 mm max height
SCALE 0.900
CERAMIC DUAL IN LINE PACKAGE
PIN 1 ID
(OPTIONAL)
A
4X .005 MIN
[0.13]
.015-.060 TYP
[0.38-1.52]
1
14
12X .100
[2.54]
14X .014-.026
[0.36-0.66]
14X .045-.065
[1.15-1.65]
.010 [0.25] C A B
.754-.785
[19.15-19.94]
8
7
B
.245-.283
[6.22-7.19]
.2 MAX TYP
[5.08]
C
.13 MIN TYP
[3.3]
SEATING PLANE
.308-.314
[7.83-7.97]
AT GAGE PLANE
.015 GAGE PLANE
[0.38]
0 -15
TYP
14X .008-.014
[0.2-0.36]
4214771/A 05/2017
NOTES:
1. All controlling linear dimensions are in inches. Dimensions in brackets are in millimeters. Any dimension in brackets or parenthesis are for
reference only. Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This package is hermitically sealed with a ceramic lid using glass frit.
4. Index point is provided on cap for terminal identification only and on press ceramic glass frit seal only.
5. Falls within MIL-STD-1835 and GDIP1-T14.
www.ti.com
EXAMPLE BOARD LAYOUT
J0014A
CDIP - 5.08 mm max height
CERAMIC DUAL IN LINE PACKAGE
(.300 ) TYP
[7.62]
SEE DETAIL A
SEE DETAIL B
1
14
12X (.100 )
[2.54]
SYMM
14X ( .039)
[1]
8
7
SYMM
LAND PATTERN EXAMPLE
NON-SOLDER MASK DEFINED
SCALE: 5X
.002 MAX
[0.05]
ALL AROUND
(.063)
[1.6]
METAL
( .063)
[1.6]
SOLDER MASK
OPENING
METAL
(R.002 ) TYP
[0.05]
.002 MAX
[0.05]
ALL AROUND
SOLDER MASK
OPENING
DETAIL A
DETAIL B
SCALE: 15X
13X, SCALE: 15X
4214771/A 05/2017
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated