DS1631,DS1632,DS1633,DS1634,DS3631, DS3632,DS3633,DS3634 DS1631 DS3631 DS1632 DS3632 DS1633 DS3633 DS1634 DS3634 CMOS Dual Peripheral Drivers Literature Number: SNOSBL9A DS1631/DS3631/DS1632/DS3632/DS1633/DS3633/ DS1634/DS3634 CMOS Dual Peripheral Drivers General Description dance OFF state with the same breakdown levels as when VCC was applied. Pin-outs are the same as the respective logic functions found in the following popular series of circuits: DS75451, DS75461. This feature allows direct conversion of present systems to the MM74C CMOS family and DS1631 series circuits with great power savings. The DS1631 series is also TTL compatible at VCC e 5V. Y Y Y Y Y e Features CMOS compatible inputs High impedance inputs PNP’s High output voltage breakdown 56V min High output current capability 300 mA max Same pin-outs and logic functions as DS75451 and DS75461 series circuits Low VCC power dissipation (28 mW both outputs ‘‘ON’’ at 5V) et The DS1631 series of dual peripheral drivers was designed to be a universal set of interface components for CMOS circuits. Each circuit has CMOS compatible inputs with thresholds that track as a function of VCC (approximately (/2 VCC). The inputs are PNPs providing the high impedance necessary for interfacing with CMOS. Outputs have high voltage capability, minimum breakdown voltage is 56V at 250 mA. The outputs are Darlington connected transistors. This allows high current operation (300 mA max) at low internal VCC current levels since base drive for the output transistor is obtained from the load in proportion to the required loading conditions. This is essential in order to minimize loading on the CMOS logic supply. Typical VCC e 5V power is 28 mW with both outputs ON. VCC operating range is 4.5V to 15V. The circuit also features output transistor protection if the VCC supply is lost by forcing the output into the high impe- Y bs ol Connection Diagrams (Dual-In-Line and Metal Can Packages) TL/F/5816–1 TL/F/5816 – 2 TL/F/5816 – 3 Top View Top View Order Number DS1632J-8 Order Number DS1633J-8 or DS3632N or DS3633N See NS Package Number J08A or N08E TL/F/5816 – 4 Top View Order Number DS1634J-8 or DS3634N O Top View Order Number DS1631J-8 or DS3631N TL/F/5816–5 TL/F/5816 – 6 TL/F/5816 – 7 TL/F/5816 – 8 Top View Top View Top View Top View (Pin 4 is electrically connected to the case.) (Pin 4 is electrically connected to the case.) (Pin 4 is electrically connected to the case.) (Pin 4 is electrically connected to the case.) Order Number DS1631H C1995 National Semiconductor Corporation Order Number DS1632H Order Number DS1633H See NS Package Number H08C TL/F/5816 Order Number DS1634H RRD-B30M105/Printed in U. S. A. DS1631/DS3631/DS1632/DS3632/DS1633/DS3633/DS1634/DS3634 CMOS Dual Peripheral Drivers July 1992 Absolute Maximum Ratings (Note 1) Operating Conditions If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Supply Voltage Voltage at Inputs Supply Voltage, VCC DS1631/DS1632/ DS1633/DS1634 16V Min Max Units 4.5 15 V 4.75 15 V b 55 a 125 §C 0 a 70 §C b 0.3V to VCC a 0.3V Output Voltage Storage Temperature Range Maximum Power Dissipation* at 25§ C Cavity Package Molded Package TO-5 Package Lead Temperature (Soldering, 4 sec. DS3631/DS3632/ DS3633/DS3634 56V b 65§ C to a 150§ C Temperature, TA DS1631/DS1632/ DS1633/DS1634 1133 mW 1022 mW 787 mW 260§ C DS3631/DS3632/ DS3633/DS3634 *Derate cavity package 7.6 mW/§ C above 25§ C; derate molded package 8.2 mW/§ C above 25§ C; derate TO-5 package 5.2 mW/§ C above 25§ C. Electrical Characteristics (Notes 2 and 3) Parameter Conditions ALL CIRCUITS VIH Logical ‘‘1’’ Input Voltage (Figure 1 ) VCC e 5V VCC e 10V VIL Logical ‘‘0’’ Input Voltage IIH Logical ‘‘1’’ Input Current IIL Logical ‘‘0’’ Input Current (Figure 1 ) 2.5 V 8.0 5 V 12.5 7.5 1.5 V VCC e 10V 5.5 2.0 V VCC e 15V 7.5 2.5 V 0.1 10 mA b 50 b 120 mA b 200 b 360 mA VCC e 15V, VIN e 15V, (Figure 2 ) VIN e 0.4V, (Figure 3 ) VCC e 5V bs ol VOL Output Low Voltage 56 1.1 V 1.1 1.4 V VCC e Min, (Figure 1 ), DS3631, DS3632, IOL e 100 mA DS3633, DS3634 IOL e 300 mA 0.85 1.0 V 1.1 1.3 V mA VIN e 0V, (Figure 4) VCC e 5V Output Low 7 11 VCC e 15V Both Drivers 14 20 mA VCC e 5V, VIN e 5V Output High 2 3 mA 7.5 10 mA Propagation to ‘‘1’’ VCC e 5V, TA e 25§ C, CL e 15 pF, RL e 50X, VL e 10V, (Figure 5 ) Propagation to ‘‘0’’ VCC e 5V, TA e 25§ C, CL e 15 pF, RL e 50X, VL e 10V, O tPD0 V 0.85 VCC e 15V, VIN e 15V Both Drivers tPD1 65 VCC e Min, (Figure 1 ), DS1631, DS1632, IOL e 100 mA DS1633, DS1634 IOL e 300 mA (Figure 4 ) ICC(1) V 2.5 Output Breakdown Voltage VCC e 15V, IOH e 250 mA, (Figure 1 ) Supply Currents Units VCC e 5V VOH ICC(0) Max 3.5 VCC e 15V DS1631/DS3631 Typ et VCC e 15V Min e Symbol (Figure 5 ) 500 ns 750 ns DS1632/DS3632 ICC(0) Supply Currents ICC(1) (Figure 4 ) VCC e 5V, VIN e 5V VIN e 0V, (Figure 4 ) VCC e 15V, VIN e 15V VCC e 5V Output Low Output High VCC e 15V 8 12 mA 18 23 mA 2.5 3.5 mA 9 14 mA tPD1 Propagation to ‘‘1’’ VCC e 5V, TA e 25§ C, CL e 15 pF, RL e 50X, VL e 10V, (Figure 5 ) 500 ns tPD0 Propagation to ‘‘0’’ VCC e 5V, TA e 25§ C, CL e 15 pF, RL e 50X, VL e 10V, (Figure 5 ) 750 ns 2 Electrical Characteristics (Notes 2 and 3) (Continued) Symbol Parameter Conditions Min Typ Max Units 7.5 12 mA 16 23 mA 2 4 mA 7.2 15 mA DS1633/DS3633 ICC(0) Supply Currents VIN e 0V, (Figure 4 ) VCC e 5V Output Low VCC e 15V ICC(1) (Figure 4 ) tPD1 Propagation to ‘‘1’’ VCC e 15V, VIN e 15V VCC e 5V, TA e 25§ C, CL e 15 pF, RL e 50X, VL e 10V, (Figure 5 ) tPD0 Propagation to ‘‘0’’ VCC e 5V, VIN e 5V Output High 500 ns VCC e 5V, TA e 25§ C, CL e 15 pF, RL e 50X, VL e 10V, (Figure 5 ) 750 ns (Figure 4 ) 7.5 12 mA 18 23 mA 3 5 mA 11 18 mA DS1634/DS3634 ICC(0) Supply Currents VIN e 0V, (Figure 4 ) ICC(1) VCC e 5V, VIN e 5V VCC e 15V, VIN e 15V Output Low VCC e 5V Output High tPD1 tPD0 e VCC e 15V Propagation to ‘‘1’’ VCC e 5V, TA e 25§ C, CL e 15 pF, RL e 50X, VL e 10V, (Figure 5 ) Propagation to ‘‘0’’ VCC e 5V, TA e 25§ C, CL e 15 pF, RL e 50X, VL e 10V, (Figure 5 ) 500 ns 750 ns et Note 1: ‘‘Absolute Maximum Ratings’’ are those values beyond which the safety of the device cannot be guaranteed. Except for ‘‘Operating Temperature Range’’ they are not meant to imply that the devices should be operated at these limits. The table of ‘‘Electrical Characteristics’’ provides conditions for actual device operation. Note 2: Unless otherwise specified min/max limits apply across the b 55§ C to a 125§ C temperature range for the DS1631, DS1632, DS1633 and DS1634 and across the 0§ C to a 70§ C range for the DS3631, DS3632, DS3633 and DS3634. All typical values are for TA e 25§ C. Note 3: All currents into device pins shown as positive, out of device pins as negative, all voltages referenced to ground unless otherwise noted. All values shown as max or min on absolute value basis. bs ol Test Circuits Input Under Test Other Input Apply Measure DS3631 VIH VIL VIH VCC IOH IOL VOH VOL DS3632 VIH VIL VIH VCC IOL IOH VOL VOH DS3633 VIH VIL GND VIL IOH IOL VOH VOL DS3634 VIH VIL GND VIL IOL IOH VOL VOH Circuit O Output Note: Each input is tested separately. FIGURE 1. VIH , VIL , VOH , VOL 3 TL/F/5816 – 9 Test Circuits (Continued) TL/F/5816 – 10 Each input is tested separately. et e FIGURE 2. IIH TL/F/5816 – 12 Both gates are tested simultaneously. TL/F/5816–11 Note A: Each input is tested separately. bs ol Note B: When testing DS1633 and DS1634 input not under test is grounded. For all other circuits it is at VCC. FIGURE 4. ICC for AND and NAND Circuits FIGURE 3. IIL O Schematic Diagram (Equivalent Circuit) TL/F/5816 – 15 4 e Switching Time Waveforms bs ol et TL/F/5816 – 13 O Note 1: The pulse generator has the following characteristics: PRR e 500 kHz, ZOUT & 50X Note 2: CL includes probe and jig capacitance FIGURE 5. Switching Times 5 TL/F/5816 – 14 et e Physical Dimensions inches (millimeters) O bs ol Metal Can Package (H) Order Number DS1631H, DS1632H, DS1633H or DS1634H NS Package Number H08C 6 et e Physical Dimensions inches (millimeters) (Continued) O bs ol Ceramic Dual-In-Line Package (J) Order Number DS1631J-8, DS1632J-8, DS1633J-8 or DS1634J-8 NS Package Number J08A 7 e et bs ol Molded Dual-In-Line Package (N) Order Number DS3631N, DS3632N, DS3633N and DS3634N NS Package Number N08E LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: O DS1631/DS3631/DS1632/DS3632/DS1633/DS3633/DS1634/DS3634 CMOS Dual Peripheral Drivers Physical Dimensions inches (millimeters) (Continued) 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated