Thin Film Precision Resistors Type CPF Series 1206 Rated Power @ 70°C: 1210 0.125W 0.2W Resistance Range (Ohms) Min: 4R7 4R7 4R7 1R0 4R7 1R0 4R7 4R7 4R7 1R0 4R7 1R0 Max: 1M0 2M5 1M0 2M5 1M0 2M5 1M0 2M5 1M0 2M5 1M0 2M5 Tolerance (%): 0.1 0.5 1 0.1 0.5 1 Code letter: B D F B D F Selection Series: E24 & E96 E24 & E96 Temp. Coefficient (ppm/°C): 15 25 50 15 25 50 15 25 50 15 25 50 15 25 50 15 25 50 Code Letter: D E D E D E C D E C D E D E C C Limiting Element Voltage: C 150V C 150V Max. Overload Voltage: 300V 300V Operating Temp. Range: -55 to +155°C -55 to +155°C 55/125/55 55/125/55 1000MΩ 1000MΩ Stability: 0.5% 0.5% Rated Power @ 70°C: 0.25W Climatic Category (°C): Insulation Resistance Dry Min: 2010 2512 0.5W Resistance Range (Ohms) Min: 4R7 4R7 4R7 1R0 4R7 1R0 4R7 4R7 4R7 1R0 4R7 1R0 Max: 1M0 3M0 1M0 3M0 1M0 3M0 1M0 3M0 1M0 3M0 1M0 3M0 Tolerance (%): 0.1 0.5 1 0.1 0.5 1 Code letter: B D F B D F Selection Series: E24 & E96 E24 & E96 Temp. Coefficient (ppm/°C): 15 25 50 15 25 50 15 25 50 15 25 50 15 25 50 15 25 50 Code Letter: D E D E D E D E D E D E C Limiting Element Voltage: C C 150V C C Max. Overload Voltage: 300V 300V Operating Temp. Range: -55 to +155°C -55 to +155°C 55/125/55 55/125/55 1000MΩ 1000MΩ 0.5% 0.5% Climatic Category (°C): Insulation Resistance Dry Min: Stability: C 150V Characteristics - Environmental Requirement Tol. ≤ 0.05% Tol. > 0.05% Item Temperature Coefficient of Resistance (TCR): Test Method AS per TCRs specified in value range table on page 1 Short Time Overload: Insulation Resistance: Endurance: Damp Heat with Load: Bending Strength: ∆R ±0.05% ∆R ±0.2% ∆R ±0.2% for high power rating >1000MΩ RCWV* 2.5 or max. overload voltage for 5 seconds ∆R ±0.05% ∆R ±0.2% >7kΩ ∆R ±0.5% ∆R ±0.5% for high power rating ∆R ±0.05% ∆R ±0.3% ∆R ±0.5% for high power rating 70 ±2°C, max. working voltage for 1000hrs with 1.5hrs “ON” and 0.5 hrs “OFF” ∆R ±0.05% Solderability: ∆R ±0.2% 95% min. coverage Resistance to Soldering Heat: +25/-55/+25/+125/+25°C ∆R ±0.05% Dielectric Withstand Voltage: ∆R ±0.2% By Type Apply 100VDC for 1 minute 40 ±2°C, 90 - 95% R.H. max. working voltage hrs with 1.5hrs “ON” and 0.5hrs “OFF” Bending amplitude 3mm for 10 seconds 245 ±5°C for 3 seconds 260 ±5°C for 10 seconds Max. overload voltage for 1 minute Thermal Shock: ∆R ±0.05% ∆R ±0.25% Low Temperature Operation: ∆R ±0.05% ∆R ±0.2% ∆R ±0.5% for high power rating -55°C to +150°C, 100 cycles 1 hour, -65°C, followed by 45 minutes of RCWV Reference Standards: MIL-STD-202, JIS-C 5201-1 Storage Temperature: 25±3°C; Humidity < 80%RH 1773200 CIS WR 03/2012 Dimensions are in millimeters and inches unless otherwise specified. Values in brackets are standard equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, go to: te.com/help Thin Film Precision Resistors Type CPF Series Marking Codes - Case Sizes 0805 to 2512 IEC 4 Digit Marking Resistance: 100Ω 2.2KΩ 10KΩ 49.9KΩ 100KΩ Marking Code: 1000 2201 1002 4992 1003 Case Sizes 0603 E24 3 Digit Marking - Example: 101=100Ω 102=1KΩ E24 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 E96 3 Digit Marking - Examples: 14C=13K7Ω, 13C=13K3Ω, 68B=4K99Ω, 68X=49.9Ω 14C 0603 E96 Marking Code Table Code E96 Code E96 Code E96 Code E96 01 100 25 178 49 316 73 562 02 102 26 182 50 324 74 576 03 105 27 187 51 332 75 590 04 107 28 191 52 340 76 604 05 110 29 196 53 348 77 619 06 113 30 200 54 357 78 634 07 115 31 205 55 365 79 649 08 118 32 210 56 374 80 665 09 121 33 215 57 383 81 681 10 124 34 221 58 392 82 698 11 127 35 226 59 402 83 715 12 130 36 232 60 412 84 732 13 133 37 237 61 422 85 750 14 137 38 243 62 432 86 768 15 140 39 249 63 442 87 787 16 143 40 255 64 453 88 806 17 147 41 261 65 464 89 825 18 150 42 267 66 475 90 845 19 154 43 274 67 487 91 866 20 158 44 280 68 499 92 887 21 162 45 287 69 511 93 909 22 165 46 294 70 523 94 931 23 169 47 301 71 536 95 953 24 174 48 309 72 549 96 976 Code A B C D E F G H X Y Z Multiplier 100 101 102 103 104 105 106 107 10-1 10-2 10-3 1773200 CIS WR 03/2012 Dimensions are in millimeters and inches unless otherwise specified. Values in brackets are standard equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, go to: te.com/help Thin Film Precision Resistors Type CPF Series Power Derating Curve 100 Rated Load (%) 80 60 40 20 0 -55 -40 -20 0 20 40 60 70 80 100 120 140 155 Ambient Temperature (°C) For resistors operated in ambient temperatures above 70°C, power rating must be derated in accordance with this curve. Dimensions L a W t b 1. Alumina Substrate 4. Edge Electrode (NiCr) 7. Resistor Layer (NiCr) 2. Bottom Electrode (Ag) 5. Barrier Layer (Ni) 8. Overcoat (Epoxy) 3. Top Electrode (Ag-Pd) 6. External Electrode (Sn) 9. Marking Part Number L W H a b Weight (g) 1000 pieces CPF0201 0.58 ±0.05 0.29 ±0.05 0.23 ±0.05 0.12 ±0.05 0.15 ±0.05 0.14 CPF0402 1.00 ±0.05 0.50 ±0.05 0.30 ±0.05 0.20 ±0.10 0.20 ±0.10 0.54 CPF0603 1.55 ±0.10 0.80 ±0.10 0.45 ±0.10 0.30 ±0.20 0.30 ±0.20 1.83 CPF0805 2.00 ±0.15 1.25 ±0.15 0.55 ±0.10 0.30 ±0.20 0.40 ±0.25 4.71 CPF1206 3.05 ±0.15 1.55 ±0.15 0.55 ±0.10 0.42 ±0.20 0.35 ±0.25 9.02 CPF1210 3.10 ±0.15 2.40 ±0.15 0.55 ±0.10 0.40 ±0.20 0.55 ±0.25 10.00 CPF2010 4.90 ±0.15 2.40 ±0.15 0.55 ±0.10 0.60 ±0.30 0.50 ±0.25 23.61 CPF2512 6.30 ±0.15 3.10 ±0.15 0.55 ±0.10 0.60 ±0.30 0.50 ±0.25 38.08 Recommend Land Pattern Type A B C CPF0201 0.25 0.3 0.40 ±0.2 CPF0402 0.5 0.5 0.60 ±0.2 CPF0603 0.8 1.0 0.90 ±0.2 CPF0805 1.0 1.0 1.35 ±0.2 CPF1206 2.0 1.15 1.70 ±0.2 CPF1210 2.0 1.15 2.50 ±0.2 CPF2010 3.6 1.4 2.50 ±0.2 CPF2512 4.9 1.6 3.10 ±0.2 1773200 CIS WR 03/2012 Dimensions are in millimeters and inches unless otherwise specified. Values in brackets are standard equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, go to: te.com/help Thin Film Precision Resistors Type CPF Series Packaging Quantity & Reel Specifications Type øA øB øC W T Paper Tape (EA) Embossed Plastic Tape (EA) CPF0201 178.0 ±1.0 60.0 +1.0 13.5 ±0.7 9.5 ±1.0 11.5 ±1.0 1000 / 5000 - CPF0402 178.0 ±1.0 60.0 +1.0 13.5 ±0.7 9.5 ±1.0 11.5 ±1.0 1000 / 5000 - CPF0603 178.0 ±1.0 60.0 +1.0 13.5 ±0.7 9.5 ±1.0 11.5 ±1.0 1000 / 5000 - CPF0805 178.0 ±1.0 60.0 +1.0 13.5 ±0.7 9.5 ±1.0 11.5 ±1.0 1000 / 5000 - CPF1206 178.0 ±1.0 60.0 +1.0 13.5 ±0.7 9.5 ±1.0 11.5 ±1.0 1000 / 5000 - CPF1210 178.0 ±1.0 60.0 +1.0 13.5 ±0.7 9.5 ±1.0 11.5 ±1.0 1000 / 5000 - CPF2010 178.0 ±1.0 60.0 +1.0 13.5 ±0.7 13.5 ±1.0 15.5 ±1.0 - 4000 CPF2512 178.0 ±1.0 60.0 +1.0 13.5 ±0.7 13.5 ±1.0 15.5 ±1.0 - 4000 Paper Tape Specification Type A B W E F P0 P1 CPF0201 0.40 ±0.05 0.70 ±0.05 8.00 ±0.10 1.75 ±0.05 3.5 ±0.05 4.00 ±0.10 2.00 ±0.05 P2 øD0 2.00 ±0.05 1.55 ±0.03 T 0.42 ±0.02 CPF0402 0.70 ±0.05 1.16 ±0.05 8.00 ±0.10 1.75 ±0.05 3.5 ±0.05 4.00 ±0.10 2.00 ±0.05 2.00 ±0.05 1.55 ±0.05 0.40 ±0.03 CPF0603 1.10 ±0.05 1.90 ±0.05 8.00 ±0.10 1.75 ±0.05 3.5 ±0.05 4.00 ±0.10 4.00 ±0.10 2.00 ±0.05 1.55 ±0.05 0.60 ±0.03 CPF0805 1.60 ±0.05 2.37 ±0.05 8.00 ±0.10 1.75 ±0.05 3.5 ±0.05 4.00 ±0.10 4.00 ±0.10 2.00 ±0.05 1.55 ±0.05 0.75 ±0.05 CPF1206 2.00 ±0.05 3.55 ±0.05 8.00 ±0.10 1.75 ±0.05 3.5 ±0.05 4.00 ±0.10 4.00 ±0.10 2.00 ±0.05 1.55 ±0.05 0.75 ±0.05 CPF1210 2.75 ±0.05 3.40 ±0.05 8.00 ±0.10 1.75 ±0.05 3.5 ±0.05 4.00 ±0.05 4.00 ±0.10 2.00 ±0.05 1.60 ±0.10 0.75 ±0.05 1773200 CIS WR 03/2012 Dimensions are in millimeters and inches unless otherwise specified. Values in brackets are standard equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, go to: te.com/help Thin Film Precision Resistors Type CPF Series Embossed Plastic Tape Specifications Type A B W E F P0 P1 P2 øD0 T CPF2010 2.85 ±0.10 5.45 ±0.10 12.0 ±0.10 1.75 ±0.10 5.5 ±0.05 4.00 ±0.05 4.00 ±0.10 2.00 ±0.05 1.50 +0.10 1.00 ±0.20 CPF2512 3.40 ±0.10 6.65 ±0.10 12.0 ±0.10 1.75 ±0.10 5.5 ±0.05 4.00 ±0.05 4.00 ±0.10 2.00 ±0.05 1.50 +0.10 1.00 ±0.20 How to Order CPF 0603 B 100R E 1 Common Part Package Size Tolerance Value TCR Packaging 100R (100 Ohms) D - 15ppm 1K0 (1000 Ohms) E - 25ppm 100K (100,000 Ohms) C - 50ppm CPF - Chip precision film resistor 0201 1206 0402 1210 0603 2010 0805 2512 B - ± 0.1% D - ±0.5% F - ± 1% 1 - 1K REEL Blank - 5K REEL TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Other logos, product and Company names mentioned herein may be trademarks of their respective owners. While TE has made every reasonable effort to ensure the accuracy of the information in this datasheet, TE does not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this datasheet are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications.