® MUR1620AT thru MUR1660AT Pb MUR1620AT/MUR1640AT/MUR1660AT Pb Free Plating Product 16 Ampere Heatsink Common Anode Fast Recovery Half Bridge Rectifiers TO-220AB Features Latest GPP technology with super fast recovery time Low forward voltage drop High current capability Low reverse leakage current High surge current capability Unit : inch (mm) .419(10.66) .196(5.00) .163(4.16) .387(9.85) .139(3.55) MIN .054(1.39) .177(4.5)MAX Automotive Inverters and Solar Inverters Plating Power Supply,SMPS,Motor Control and UPS Car Audio Amplifiers and Sound Device Systems .038(0.96) .019(0.50) Mechanical Data Case: Heatsink TO-220AB Epoxy: UL 94V-0 rate flame retardant Terminals: Solderable per MIL-STD-202 method 208 Polarity: As marked on diode body Mounting position: Any Weight: 2.2 gram approximately .1(2.54) .624(15.87) .50(12.7)MIN Application .548(13.93) .269(6.85) .226(5.75) .045(1.15) .025(0.65)MAX .1(2.54) Case Case Case Negative Positive Common Cathode Common Anode Suffix "CT" Suffix "AT" Series Tandem Polarity Suffix "ST" Case Doubler Tandem Polarity Suffix "DT" MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS o Rating at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. MUR1640AT MUR1660AT UNIT SYMBOL MUR1620AT Maximum Recurrent Peak Reverse Voltage VRRM 200 400 600 V Maximum RMS Voltage VRMS 140 280 420 V Maximum DC Blocking Voltage VDC 200 400 600 V Maximum Average Forward Rectified 16.0 IF(AV) o Current TC=100 C A Peak Forward Surge Current, 8.3ms single Half sine-wave superimposed on rated load IFSM 175 VF 0.98 150 A (JEDEC method) Maximum Instantaneous Forward Voltage @ 8.0 A 1.3 o Maximum DC Reverse Current @TJ=25 C o At Rated DC Blocking Voltage @TJ=125 C IR 5.0 uA uA nS Trr 35 Typical junction Capacitance (Note 2) CJ 90 Operating Junction and Storage Temperature Range V 100 Maximum Reverse Recovery Time (Note 1) Typical Thermal Resistance (Note 3) 1.7 R JC 2.2 TJ, TSTG -55 to + 150 pF o C/W o C NOTES : (1) Reverse recovery test conditions IF = 0.5A, IR = 1.0A, Irr = 0.25A. (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts DC. (3) Thermal Resistance junction to case. Rev.05 © 2006 Thinki Semiconductor Co., Ltd. Page 1/2 http://www.thinkisemi.com/ ® MUR1620AT thru MUR1660AT FIG.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1 - FORWARD CURRENT DERATING CURVE 200 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 16 13 10 8 6 4 60 Hz Resistive or Inductive load Pulse Width 8.3ms Single Half-Sire-Wave (JEDEC Method) 175 150 125 100 75 50 25 0 0 0 50 100 150 1 CASE TEMPERATURE, C 100 FIG.4 - TYPICAL REVERSE CHARACTERISTICS FIG.3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1000 80 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES IINSTANTANEOUS FORWARD CURRENT, AMPERES 10 NUMBER OF CYCLES AT 60Hz o MUR1620AT MUR1640AT 8 MUR1660AT 0.1 o TJ=25 C PULSE WIDTH=300uS 1% DUTY CYCLE 0.01 0.2 0.4 0.6 0.8 1.0 1.2 1.4 o TJ=125 C 100 10 o TJ=25 C 1 0.1 0 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,% FIG.5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF 1000 o TJ = 25 C f = 1.0 MHZ Vsig = 50mVp-p 100 10 0.1 1.0 4.0 10 100 REVERSE VOLTAGE, VOLTS Rev.05 © 2006 Thinki Semiconductor Co., Ltd. Page 2/2 http://www.thinkisemi.com/