TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 6-W STEREO AUDIO POWER AMPLIFIER • • • • FEATURES • • • TDA1517P Compatible High Power Outputs (6 W/Channel) Surface Mount Availability 20-Pin Thermal SOIC PowerPAD™ Thermal Protection Fixed Gain: 20 dB Mute and Standby Operation Supply Range: 9.5 V - 18 V DWP PACKAGE (TOP VIEW) NE PACKAGE (TOP VIEW) IN1 SGND SVRR OUT1 PGND OUT2 VCC M/SB IN2 GND/HS 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 GND/HS GND/HS GND/HS GND/HS GND/HS GND/HS GND/HS GND/HS GND/HS GND/HS GND/HS IN1 NC SGND SVRR NC OUT1 OUT1 PGND GND/HS 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 GND/HS IN2 NC M/SB VCC NC OUT2 OUT2 PGND GND/HS Cross Section View Showing PowerPAD NC – No internal connection DESCRIPTION The TPA1517 is a stereo audio power amplifier that contains two identical amplifiers capable of delivering 6 W per channel of continuous average power into a 4-Ω load at 10% THD+N or 5 W per channel at 1% THD+N. The gain of each channel is fixed at 20 dB. The amplifier features a mute/standby function for power-sensitive applications. The amplifier is available in the PowerPAD™ 20-pin surface-mount thermally-enhanced package (DWP) that reduces board space and facilitates automated assembly while maintaining exceptional thermal characteristics. It is also available in the 20-pin thermally enhanced DIP package (NE). AVAILABLE OPTIONS PACKAGED DEVICES (1) (1) (2) TA THERMALLY ENHANCED PLASTIC DIP THERMALLY ENHANCED SURFACE MOUNT (DWP) (2) -40°C to 85°C TPA1517NE TPA1517DWP (2) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI Web site at www.ti.com. The DWP package is available taped and reeled. To order a taped and reeled part, add the suffix R (e.g., TPA1517DWPR). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1997–2007, Texas Instruments Incorporated TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Terminal Functions TERMINAL DWP NO. NE NO. I/O IN1 2 1 I IN1 is the audio input for channel 1. SGND 4 2 I SGND is the input signal ground reference. SVRR 5 3 OUT1 7, 8 4 PGND 9, 12 5 OUT2 13, 14 6 O OUT2 is the audio output for channel 2. VCC 16 7 I VCC is the supply voltage input. M/SB 17 8 I M/SB is the mute/standby mode enable. When held at less than 2 V, this signal enables the TPA1517 for standby operation. When held between 3.5 V and 8.2 V, this signal enables the TPA1517 for mute operation. When held above 9.3 V, the TPA1517 operates normally. 19 9 I IN2 in the audio input for channel 2. 1, 10, 11, 20 10-20 NAME IN2 GND/HS DESCRIPTION SVRR is the midrail bypass. O OUT1 is the audio output for channel 1. PGND is the power ground reference. GND/HS are the ground and heatsink connections. All GND/HS terminals are connected directly to the mount pad for thermal-enhanced operation. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) UNIT VCC Supply voltage VI Input voltage (IN1, IN2) 22 V 22 V Internally limited (See Dissipation Rating Table) Continuous total power dissipation TA Operating free-air temperature range -40°C to 85°C TJ Operating junction temperature range -40°C to 150°C Tstg Storage temperature range -65°C to 85°C DISSIPATION RATING TABLE (1) PACKAGE TA ≤ 25°C DERATING FACTOR TA = 70°C TA = 85°C DWP (1) 2.94 W 23.5 mW/°C 1.88 W 1.53 W NE (1) 2.85 W 22.8 mW/°C 1.82 W 1.48 W See the Texas Instruments document, PowerPAD Thermally Enhanced Package Application Report (literature number SLMA002), for more information on the PowerPAD package. The thermal data was measured on a PCB layout based on the information in the section entitled Texas Instruments Recommended Board for PowerPAD on page 33 of the before mentioned document. RECOMMENDED OPERATING CONDITIONS MIN 2 NOM MAX UNIT VCC Supply voltage 9.5 18 V TA Operating free-air temperature -40 85 °C Submit Documentation Feedback TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 ELECTRICAL CHARACTERISTICS VCC = 12 V, TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS ICC Supply current VO(DC) DC output voltage V(M/SB) Voltage on M/SB terminal for normal operation VO(M) Mute output voltage ICC(SB) Supply current in standby mode (1) See Note MIN (1) TYP MAX 45 80 6 V 2 7 mA V 9.6 VI = 1 V (max) UNIT mV 100 µA At 9.5 V < VCC < 18 V the DC output voltage is approximately VCC/2. OPERATING CHARACTERISTIC VCC = 12 V, RL = 4Ω , f = 1 kHz, TA = 25°C PARAMETER PO Output power (1) SNR Signal-to-noise ratio THD Total harmonic distortion IO(SM) Non-repetitive peak output current IO(RM) Repetitive peak output current TEST CONDITIONS 3 THD = 10% 6 PO = 1 W, RL = 8Ω , 3 dB 1 dB Supply ripple rejection ratio M/SB = On, f = 1 kHz Vn Noise output voltage (2) f = 1 kHz 4 A 2.5 A 45 Hz 20 kHz -65 dB 60 kΩ Rs = 0, M/SB = On 50 µV(rms) Rs= 10 kΩ, M/SB = On 70 µV(rms) 50 µV(rms) Rs = 10 kΩ -58 Gain 18.5 Channel balance (1) (2) dB 0.1% M/SB = Mute Channel separation UNIT W 84 High-frequency roll-off Input impedance TYP MAX THD = 0.2% Low-frequency roll-off ZI MIN dB 20 21 0.1 1 TYP MAX 50 90 dB Output power is measured at the output terminals of the IC. Noise voltage is measured in a bandwidth of 20 Hz to 20 kHz. ELECTRICAL CHARACTERISTICS VCC = 14.5 V, TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS ICC Supply current VO(DC) DC output voltage V(M/SB) Voltage on M/SB terminal for normal operation VO(M) Mute output voltage ICC(SB) Supply current in standby mode (1) See Note (1) MIN 7.25 V 2 7 mA V 9.6 VI = 1 V (max) UNIT mV 100 µA At 9.5 V < VCC < 18 V the DC output voltage is approximately VCC/2. Submit Documentation Feedback 3 TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 OPERATING CHARACTERISTIC VCC = 14.5 V, RL = 4Ω , f = 1 kHz, TA = 25°C PARAMETER PO Output power (1) SNR Signal-to-noise ratio THD Total harmonic distortion IO(SM) Non-repetitive peak output current IO(RM) Repetitive peak output current TEST CONDITIONS W W 84 dB PO = 1 W 0.1% 4 1 dB Supply ripple rejection ratio M/SB = On Noise output voltage (2) A 2.5 A 45 Hz 20 kHz -65 dB 60 kΩ Rs = 0, M/SB = On 50 µV(rms) Rs= 10 kΩ, M/SB = On 70 µV(rms) 50 µV(rms) M/SB = Mute Channel separation Rs = 10 kΩ Gain -58 18.5 Channel balance (1) (2) UNIT 6 High-frequency roll-off Vn MAX THD < 10% 3 dB Input impedance TYP 4.5 Low-frequency roll-off ZI MIN THD = 0.2% dB 20 21 dB 0.1 1 dB Output power is measured at the output terminals of the IC. Noise voltage is measured in a bandwidth of 22 Hz to 22 kHz. TYPICAL CHARACTERISTICS Table of Graphs FIGURE ICC Supply current vs Supply voltage Power supply rejection ratio vs Frequency 2, 3 vs Frequency 4, 5, 6 VCC = 12 V vs Power output 10, 11 vs Frequency 7, 8, 9 vs Power output 12, 13 Crosstalk vs Frequency 14, 15 Gain vs Frequency 16 Phase vs Frequency 16 Vn Noise voltage vs Frequency 17, 18 PO Output power vs Supply voltages Load resistance 1920 PD Power dissipation vs Output power 21, 22 THD + N Total harmonic distortion plus noise VCC = 14.5 V 4 1 Submit Documentation Feedback TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 SUPPLY CURRENT vs SUPPLY VOLTAGE SUPPLY RIPPLE REJECTION RATIO vs FREQUENCY 100 0 VCC = 12 V RL = 4 Ω CB = 100 µF Supply Ripple Rejection Ratio - dB I CC - Supply Current - mA - 10 75 50 25 - 20 - 30 - 40 - 50 - 60 - 70 - 80 - 90 0 8 10 12 14 16 18 - 100 100 20 Figure 1. Figure 2. SUPPLY RIPPLE REJECTION RATIO vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 10% VCC = 14.5 V RL = 4 Ω THD+N - Total Harmonic Distortion + Noise Supply Ripple Rejection Ratio - dB 10 k f - Frequency - Hz 0 - 10 1k VCC - Supply Voltage - V - 20 - 30 - 40 - 50 - 60 - 70 - 80 - 90 VCC = 12 V RL = 4 Ω PO = 3 W Both Channels 1% 0.1% 0.01% - 100 100 1k f - Frequency - Hz 10 K 20 100 1k 10 k 20 k f - Frequency - Hz Figure 3. Figure 4. Submit Documentation Feedback 5 TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 10% VCC = 12 V RL = 8 Ω PO = 1 W Both Channels THD+N - Total Harmonic Distortion + Noise THD+N - Total Harmonic Distortion + Noise 10% 1% 0.1% 0.01% 100 1k 0.1% 20 10 k 20 k 100 1k 10 k 20 k f - Frequency - Hz f - Frequency - Hz Figure 5. Figure 6. TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 10% 10% VCC = 14.5 V RL = 4 Ω PO = 3 W THD+N - Total Harmonic Distortion + Noise THD+N - Total Harmonic Distortion + Noise 1% 0.01% 20 1% 0.1% 0.01% VCC = 14.5 V RL = 8 Ω PO = 1.5 W 1% 0.1% 0.01% 20 6 VCC = 12 V RL = 32 Ω PO = 0.25 W 100 1k 10 k 20 k 20 100 1k f - Frequency - Hz f - Frequency - Hz Figure 7. Figure 8. Submit Documentation Feedback 10 k 20 k TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs POWER OUTPUT 10% VCC = 14.5 V RL = 32 Ω PO = 0.25 W THD+N - Total Harmonic Distortion + Noise THD+N - Total Harmonic Distortion + Noise 10% 1% 0.1% 0.01% 20 100 f = 20 kHz 1% f = 20 Hz 0.1% f = 1 kHz 0.01% 0.01 10 k 20 k f - Frequency - Hz 0.1 1 PO - Power Output - W Figure 9. Figure 10. TOTAL HARMONIC DISTORTION + NOISE vs POWER OUTPUT TOTAL HARMONIC DISTORTION + NOISE vs POWER OUTPUT 1% 10% VCC = 12 V RL = 8 Ω Both Channels THD+N - Total Harmonic Distortion + Noise 10% THD+N - Total Harmonic Distortion + Noise 1k VCC = 12 V RL = 4 Ω Both Channels f = 20 kHz f = 20 Hz 0.1% f = 1 kHz 0.01% 0.01 0.1 1 PO - Power Output - W 10 10 VCC = 14.5 V RL = 4 Ω Both Channels f = 20 kHz 1% f = 20 Hz 0.1% f = 1 kHz 0.01% 0.01 Figure 11. 0.1 1 PO - Power Output - W 10 Figure 12. Submit Documentation Feedback 7 TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 TOTAL HARMONIC DISTORTION + NOISE vs POWER OUTPUT - 40 VCC = 14.5 V RL = 8 Ω Both Channels VCC = 12 V RL = 4 Ω PO = 3 W Both Channels - 45 - 50 f = 20 kHz 1% Crosstalk - dB THD+N - Total Harmonic Distortion + Noise 10% CROSSTALK vs FREQUENCY f = 20 Hz - 55 - 60 - 65 0.1% - 70 f = 1 kHz - 75 0.01% 0.01 - 80 0.1 1 PO - Power Output - W 20 10 100 1k f - Frequency - Hz Figure 13. Figure 14. CROSSTALK vs FREQUENCY - 40 VCC = 14.5 V RL = 4 Ω PO = 5 W Both Channels - 45 Crosstalk - dB - 50 - 55 - 60 - 65 - 70 - 75 - 80 20 100 1k f - Frequency - Hz Figure 15. 8 Submit Documentation Feedback 10 k 20 k 10 k 20 k TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 GAIN AND PHASE vs FREQUENCY 20 VCC = 12 V RL = 4 Ω Gain 200° 10 100° - 10 Phase Gain - dB 0 0° Phase - 20 -100° - 30 - 40 -200° 10 100 1k 10 k 100 k 1M f - Frequency - Hz Figure 16. NOISE VOLTAGE vs FREQUENCY NOISE VOLTAGE vs FREQUENCY 1 1 VCC = 14.5 V BW = 22 Hz to 22 kHz RL = 4 Ω Both Channels V n - Noise Voltage - mV V n - Noise Voltage - mV VCC = 12 V BW = 22 Hz to 22 kHz RL = 4 Ω Both Channels 0.1 0.01 20 100 1k 10 k 20 k 0.1 0.01 20 100 1k f - Frequency - Hz f - Frequency - Hz Figure 17. Figure 18. Submit Documentation Feedback 10 k 20 k 9 TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 OUTPUT POWER vs SUPPLY VOLTAGE OUTPUT POWER vs LOAD RESISTANCE 8 6 THD < 1% THD < 1% 5 PO - Output Power - W PO - Output Power - W 6 RL = 4 Ω 4 RL = 8 Ω 2 VCC = 14.5 V 4 VCC = 12 V 3 2 1 0 0 8 9 10 11 12 13 14 15 VCC - Supply Voltage - V 16 17 18 2 4 6 Figure 19. Figure 20. POWER DISSIPATION vs OUTPUT POWER POWER DISSIPATION vs OUTPUT POWER 3.5 3.5 VCC = 14.5 V VCC = 12 V 3 PD - Power Dissipation - W PD - Power Dissipation - W 3 2.5 RL = 4 Ω 2 1.5 RL = 8 Ω 1 RL = 4 Ω 2.5 2 RL = 8 Ω 1.5 1 0.5 0.5 0 1 2 3 4 PO - Output Power - W 5 6 0 Figure 21. 10 8 10 12 14 16 18 20 22 24 26 28 30 32 RL - Load Resistance - Ω 1 2 3 4 PO - Output Power - W Figure 22. Submit Documentation Feedback 5 6 TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 APPLICATION INFORMATION AMPLIFIER OPERATION The TPA1517 is a stereo audio power amplifier designed to drive 4-Ω speakers at up to 6 W per channel. Figure 23 is a schematic diagram of the minimum recommended configuration of the amplifier. Gain is internally fixed at 20 dB (gain of 10 V/V). VCC 7 1 IN1 1 µF + 60 k COR – + – + OUT1 4 ×1 470 µF 2.1 Vref 2 Ref 1 µF CS CIR Right VCC 5 VCC SGND VCC 18 kΩ PGND 2 kΩ 15 kΩ ×1 3 SVRR CB Mute Standby M/SB 8 2 kΩ 15 kΩ 2.2 µF 10 kΩ S1 Mute/Standby Switch (see Note A) 18 kΩ 6.8 kΩ 2.1 Vref S2 Mute/Standby Select (see Note B) COL 60 k CIL – + 9 IN2 Left + – + 1 µF OUT2 6 ×1 470 µF GND/HS 10 – 20 Copper Plane A. When S1 is open, the TPA1517 operates normally. When this switch is closed, the device is in mute/standby mode. B. When S2 is open, activating S1 places the TPA1517 in mute mode. When S2 is closed, activating S1 places the TPA1517 in standby mode. C. The terminal numbers are for the 20-pin NE package. Figure 23. TPA1517 Minimum Configuration The following equation is used to relate gain in V/V to dB: ǒ Ǔ G dB + 20 LOG G VńV Submit Documentation Feedback 11 TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 APPLICATION INFORMATION (continued) The audio outputs are biased to a midrail voltage which is shown by the following equation: V V MID + CC 2 The audio inputs are always biased to 2.1 V when in mute or normal mode. Any dc offset between the input signal source and the input terminal is amplified and can seriously degrade the performance of the amplifier. For this reason, it is recommended that the inputs always be connected through a series capacitor (ac coupled). The power outputs, also having a dc bias, must be connected to the speakers via series capacitors. MUTE/STANDBY OPERATION The TPA1517 has three modes of operation; normal, mute, and standby. They are controlled by the voltage on the M/SB terminal as described in Figure 24. In normal mode, the TPA1517 amplifies the signal applied to the two input terminals providing low impedance drive to speakers connected to the output terminals. In mute mode, the amplifier retains all bias voltages and quiescent supply current levels but does not pass the input signal to the output. In standby mode, the internal bias generators and power-drive stages are turned off, thereby reducing the supply current levels. V I(M/SB) - Input Voltage on M/SB - V 22 NORMAL 9.3 8.2 Undetermined State MUTE 3.5 Undetermined State 2 STANDBY 0 Figure 24. Standby, Mute, and Normal (On) Operating Conditions The designer must take care to place the control voltages within the defined ranges for each desired mode, whenever an external circuit is used to control the input voltage at the M/SB terminal. The undefined area can cause unpredictable performance and should be avoided. As the control voltage moves through the undefined areas, pop or click sounds may be heard in the speaker. Moving from mute to normal causes a very small click sound. Whereas moving from standby to mute can cause a much larger pop sound. Figure 25 shows external circuitry designed to help reduce transition pops when moving from standby mode to normal mode. 12 Submit Documentation Feedback TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 APPLICATION INFORMATION (continued) Figure 25 is a reference schematic that provides TTL-level control of the M/SB terminal. A diode network is also included which helps reduce turn-on pop noises. The diodes serve to drain the charge out of the output coupling capacitors while the amplifier is in shutdown mode. When the M/SB voltage is in the normal operating range, the diodes have no effect on the ac performance of the system. VCC 7 1 µF CS CIR 1 Right VCC IN1 1 µF + 60 k COR 470 µF – + – + OUT1 4 ×1 1N914 2.1 Vref 220 Ω 18 kΩ 2 Ref 5 SGND S1 See Note A VCC VCC 2 kΩ PGND 10 kΩ 10 kΩ 15 kΩ ×1 3 SVRR Mute Standby M/SB 8 47 kΩ 47 kΩ 47 kΩ Q1 CB 2.2 µF 15 kΩ Q2 2 kΩ 1N914 S2 See Note B 6.8 kΩ 18 kΩ TTL Control Low – Mute High – On 10 kΩ 2.1 Vref COL 60 k CIL 9 IN2 Left 1 µF – + + – + OUT2 6 ×1 470 µF GND/HS 10 – 20 Copper Plane A. When S1 is closed, the depop circuitry is active during standby mode. B. When S2 is open, activating S1 places the TPA1517 in mute mode. When S2 is closed, activating S1 places the TPA1517 in standby mode. C. The terminal numbers are for the 20-pin NE package. Figure 25. TTL Control with POP Reduction Submit Documentation Feedback 13 TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 APPLICATION INFORMATION (continued) COMPONENT SELECTION Some of the general concerns for selection of capacitors are: • Leakage currents on aluminum electrolytic capacitors • ESR (equivalent series resistance) • Temperature ratings LEAKAGE CURRENTS Leakage currents on most ceramic, polystyrene, and paper capacitors are negligible for this application. Leakage currents for aluminum electrolytic and tantalum tend to be higher. This is especially important on the input terminals and the SVRR capacitor. These nodes encounter from 3 V to 7 V, and need to have leakage currents less than 1 µA to keep from affecting the output power and noise performance. EQUIVALENT SERIES RESISTANCE ESR is mainly important on the output coupling capacitor, where even 1Ω of ESR in CO with an 8-Ω speaker can reduce the output drive power by 12.5%. ESR should be considered across the frequency range of interest, (i.e., 20 Hz to 20 kHz). The following equation calculates the amount of power lost in the coupling capacitor: % Power in C O + ESR RL The power supply decoupling requires a low ESR as well to take advantage of the full output drive current. TEMPERATURE RANGE The temperature range of the capacitors are important. Many of the high-density capacitors perform differently at different temperatures. When consistent high performance is required from the system overtemperature in terms of low THD, maximum output power, and turn-on/off popping, then interactions of the coupling capacitors and the SVRR capacitors need to be considered, as well as the change in ESR on the output capacitor with temperature. TURN-ON POP CONSIDERATION To select the proper input coupling capacitor, the designer should select a capacitor large enough to allow the lowest desired frequency pass and small enough that the time constant is shorter than the output RC time constant to minimize turn-on popping. The input time constant for the TPA1517 is determined by the input 60-kΩ resistance of the amplifier, and the input coupling capacitor according to the following generic equation: 1 TC + 2pRC For example, 8-Ω speakers and 220-µF output coupling capacitors would yield a 90-Hz cut-off point for the output RC network. The input network should be the same speed or faster ( > 90 Hz TC). A good choice would be 180 Hz. As the input resistance is 60 kΩ, a 14-nF input coupling capacitor would do. The bypass-capacitor time constant should be much larger (×5) than either the input coupling capacitor time constant or the output coupling capacitor time constants. In the previous example with the 220-µF output coupling capacitor, the designer should want the bypass capacitor, TC, to be in the order of 18 Hz or lower. To get an 18-Hz time constant, CB is required to be 1 µF or larger because the resistance this capacitor sees is 7.5 kΩ. In summary, follow one of the three simple relations presented below, depending on the tradeoffs between low frequency response and turn-on pop. 1. If depop performance is the top priority, then follow: 7500 C B u 5RLC O u 300000 C I 2. If low frequency ac response is more important but depop is still a consideration then follow: 1 t 10 Hz 2p60000 C I 14 Submit Documentation Feedback TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 APPLICATION INFORMATION (continued) 3. If low frequency response is most important and depop is not a consideration then follow: 1 1 ≤ ≤ f low 2p60000 C I 2pRL C I THERMAL APPLICATIONS Linear power amplifiers dissipate a significant amount of heat in the package under normal operating conditions. A typical music CD requires 12 dB to 15 dB of dynamic headroom to pass the loudest portions without distortion as compared with the average power output. Figure 19 shows that when the TPA1517 is operating from a 12-V supply into a 4-Ω speaker that approximately 3.5 W peaks are possible. Converting watts to dB using the following equation: ǒ Ǔ P P dB + 10Log P W ref ǒ Ǔ + 10Log 3.5 1 + 5.44 dB Subtracting dB for the headroom restriction to obtain the average listening level without distortion yields the following: 5.44 dB * 15 dB + * 9.56 dB (15 dB headroom) 5.44 dB * 12 dB + * 6.56 dB (12 dB headroom) Converting dB back into watts: P ń10 P W + 10 dB Pref + 111 mW (15 dB headroom) + 221 mW (12 dB headroom) This is valuable information to consider when attempting to estimate the heat dissipation requirements for the amplifier system. Comparing the absolute worst cast, which is 3.5 W of continuous power output with 0 dB of headroom, against 12-dB and 15-dB applications drastically affects maximum ambient temperature ratings for the system. Using the power dissipation curves for a 12-V, 4-Ω system, internal dissipation in the TPA1517 and maximum ambient temperatures are shown in Table 1. Table 1. TPA1517 Power Rating PEAK OUTPUT POWER (W) AVERAGE OUTPUT POWER POWER DISSIPATION (W/Channel) MAXIMUM AMBIENT TEMPERATURE 3.5 3.5 W 2.1 -34°C 3.5 1.77 W (3 dB) 2.4 -61°C 3.5 884 mW (6 dB) 2.25 -48°C 3.5 442 mW (9 dB) 1.75 -4°C 3.5 221 mW (12 dB) 1.5 18°C 3.5 111 mW (15 dB) 1.25 40°C Submit Documentation Feedback 15 TPA1517 www.ti.com SLOS162D – MARCH 1997 – REVISED FEBRUARY 2007 The maximum ambient temperature depends on the heatsinking ability of the PCB system. The derating factor for the NE package with 7 square inches (17.78 cm) of copper area is 22.8 mW/°C. Converting this to θJA: 1 θ JA + Derating For 0 CFM : + 1 0.0228 + 43.9°CńW To calculate maximum ambient temperatures, first consider that the numbers from the dissipation graphs are per channel so the dissipated heat needs to be doubled for two channel operation. Given θJA, the maximum allowable junction temperature and the total internal dissipation, the maximum ambient temperature can be calculated with the following equation. The maximum recommended junction temperature for the TPA1517 is 150°C. T A Max + T J Max * q JA P D + 150 * 43.9(1.25 2) + 40°C (15 dB headroom, 0 CFM) Table 1 clearly shows that for most applications some airflow is required to keep junction temperatures in the specified range. The TPA1517 is designed with thermal protection that turns the device off when the junction temperature surpasses 150°C to prevent damage to the IC. Using the DWP package on a multilayer PCB with internal ground planes can achieve better thermal performance. Table 1 was calculated for a maximum volume system; when the output level is reduced, the numbers in the table change significantly. Also using 8-Ω speakers dramatically increases the thermal performance by increasing amplifier efficiency. NE THERMAL RESISTANCE, θJA vs COPPER AREA 90 80 θJA– Theta JA – oC/W 70 60 50 40 30 20 10 0 0 1 2 3 4 5 6 7 Copper Area Figure 26. 16 Submit Documentation Feedback 8 9 10 PACKAGE OPTION ADDENDUM www.ti.com 15-Apr-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) HPA00892DWPR ACTIVE SO PowerPAD DWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 TPA1517 TPA1517DWP ACTIVE SO PowerPAD DWP 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 TPA1517 TPA1517DWPG4 ACTIVE SO PowerPAD DWP 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 TPA1517 TPA1517DWPR ACTIVE SO PowerPAD DWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 TPA1517 TPA1517DWPRG4 ACTIVE SO PowerPAD DWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 TPA1517 TPA1517NE ACTIVE PDIP NE 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -40 to 85 TPA1517NE TPA1517NEE4 ACTIVE PDIP NE 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -40 to 85 TPA1517NE (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 15-Apr-2017 (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Apr-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPA1517DWPR Package Package Pins Type Drawing SO Power PAD DWP 20 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2000 330.0 24.4 Pack Materials-Page 1 10.8 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 13.3 2.7 12.0 24.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Apr-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPA1517DWPR SO PowerPAD DWP 20 2000 367.0 367.0 45.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2017, Texas Instruments Incorporated