IDT IDT5V40501 Locoâ ¢ pll clock multiplier Datasheet

DATASHEET
IDT5V40501
LOCO™ PLL CLOCK MULTIPLIER
Description
Features
The IDT5V40501 LOCOTM is the most cost effective way to
generate a high-quality, high-frequency clock output from a
lower frequency crystal or clock input. The name LOCO
stands for Low Cost Oscillator, as it is designed to replace
crystal oscillators in most electronic systems. Using
Phase-Locked Loop (PLL) techniques, the device uses a
standard fundamental mode, inexpensive crystal to
produce output clocks up to 160 MHz.
• Packaged as 8-pin SOIC or MSOP
• Available in RoHS 5 (green) or RoHS 6 (green and lead
free) compliant packaging
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Stored in the chip’s ROM is the ability to generate nine
different multiplication factors, allowing one chip to output
many common frequencies (see table on page 2).
The device also has an output enable pin which tri-states
the clock output when the OE pin is taken low.
This product is intended for clock generation. It has low
output jitter (variation in the output period), but input to
output skew and jitter are not defined or guaranteed. For
applications which require defined input to output skew, use
the ICS570B.
The IDT5V40501 is an enhanced performance version of
the ICS501 and ICS501B and should be used for all new
designs.
IDT’s lowest cost PLL clock
Zero ppm multiplication error
Input crystal frequency of 5 - 27 MHz
Input clock frequency of 2 - 50 MHz
Output clock frequencies up to 100 MHz
Extremely low jitter of 15 ps (one sigma)
Compatible with all popular CPUs
Duty cycle of 45/55 up to 160 MHz
Nine selectable frequencies
Operating voltage of 3.3 V
Tri-state output for board level testing
25 mA drive capability at TTL levels
Ideal for oscillator replacement
Industrial temperature version available
Advanced, low-power CMOS process
Block Diagram
VDD
S1:0
2
PLL Clock
Multiplier
Circuitry
and ROM
X1/ICLK
Crystal or
Clock input
Crystal
Oscillator
CLK
X2
Optional crystal capacitors
GND
IDT™ LOCO™ PLL CLOCK MULTIPLIER
1
OE
IDT5V40501
REV C 102808
IDT5V40501
LOCO™ PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
Pin Assignment
Clock Input Table
S1 S0
CLK
Minimum Input
0
0
4X input
4 MHz
X1/ I CLK
1
8
X2
0
M
5.3125X input
4 MHz
VDD
2
7
OE
0
1
5X input
3 MHz
GND
3
6
S0
M
0
6.25X input
3.5 MHz
M
M
2X input
7.5 MHz
M
1
3.125X input
7 MHz
1
0
6X input
3 MHz
1
M
3X input
5 MHz
1
1
8X input
2 mhZ
S1
5
4
CLK
8 Pi n ( 150 mi l ) SOI C
0 = connect directly to ground
1 = connect directly to VDD
M = leave unconnected (floating)
Common Output Frequency Examples (MHz)
Output
20
24
30
32
33.33
37.5
40
48
50
60
Input
10
12
10
16
16.66
12
10
12
16.66
10
Selection (S1, S0)
M, M
M, M
1, M
M, M
M, M
M, 1
0, 0
0, 0
1, M
1, 0
Output
62.5
64
66.66
72
75
80
83.33
90
100
20
16
16.66
12
12
10
16.66
15
20
M, 1
0, 0
0, 0
1, 0
M, 0
1, 1
0, 1
1, 0
0, 1
Input
Selection (S1, S0)
Pin Descriptions
Pin
Number
Pin
Name
Pin
Type
1
XI/ICLK
Input
Crystal connection or clock input.
2
VDD
Power
Connect to +3.3 V.
3
GND
Power
Connect to ground.
4
S1
Tri-level Input
5
CLK
Output
6
S0
Tri-level Input
7
OE
Input
8
X2
Output
IDT™ LOCO™ PLL CLOCK MULTIPLIER
Pin Description
Select 1 for output clock. Connect to GND or VDD or float.
Clock output per table above.
Select 0 for output clock. Connect to GND or VDD or float.
Output enable. Tri-states CLK output when low. Internal pull-up.
Crystal connection. Leave unconnected for clock input.
2
IDT5V40501
REV C 102808
IDT5V40501
LOCO™ PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
External Components
Crystal Load Capacitors
The total on-chip capacitance is approximately 12 pF. A
parallel resonant, fundamental mode crystal should be
used. The device crystal connections should include pads
for small capacitors from X1 to ground and from X2 to
ground. These capacitors are used to adjust the stray
capacitance of the board to match the nominally required
crystal load capacitance. Because load capacitance can
only be increased in this trimming process, it is important to
keep stray capacitance to a minimum by using very short
PCB traces (and no vias) between the crystal and device.
Crystal capacitors, if needed, must be connected from each
of the pins X1 and X2 to ground.
Decoupling Capacitor
As with any high-performance mixed-signal IC, the
IDT5V40501 must be isolated from system power supply
noise to perform optimally.
A decoupling capacitor of 0.01µF must be connected
between VDD and the GND. It must be connected close to
the IDT5V40501 to minimize lead inductance. No external
power supply filtering is required for the IDT5V40501.
Series Termination Resistor
A 33Ω terminating resistor can be used next to the CLK pin
for trace lengths over one inch.
The value (in pF) of these crystal caps should equal (CL -12
pF)*2. In this equation, CL= crystal load capacitance in pF.
Example: For a crystal with a 16 pF load capacitance, each
crystal capacitor would be 8 pF [(16-12) x 2 = 8].
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the IDT5V40501. These ratings, which
are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at
these or any other conditions above those indicated in the operational sections of the specifications is not implied.
Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical
parameters are guaranteed only over the recommended operating temperature range.
Item
Rating
Supply Voltage, VDD
7V
All Inputs and Outputs
-0.5 V to VDD+0.5 V
Ambient Operating Temperature
-40 to +85° C
Storage Temperature
-65 to +150° C
Soldering Temperature
260° C
Recommended Operation Conditions
Parameter
Min.
Ambient Operating Temperature (commercial)
Ambient Operating Temperature (industrial)
Power Supply Voltage (measured in respect to GND)
IDT™ LOCO™ PLL CLOCK MULTIPLIER
3
Max.
Units
0
+70
°C
-40
85
°C
+3.465
V
+3.135
Typ.
3.3
IDT5V40501
REV C 102808
IDT5V40501
LOCO™ PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
DC Electrical Characteristics
VDD=3.3 V ±5% , Ambient temperature -40 to +85° C, unless stated otherwise
Parameter
Operating Voltage
Symbol
Conditions
VDD
Input High Voltage, ICLK only
VIH
ICLK (pin 1)
Input Low Voltage, ICLK only
VIL
ICLK (pin 1)
Input High Voltage
VIH
OE (pin 7)
Input Low Voltage
VIL
OE (pin 7)
Input High Voltage
VIH
S0, S1
Input Low Voltage
VIL
S0, S1
Output High Voltage
VOH
IOH = -25 mA
Output Low Voltage
VOL
IOL = 25 mA
Min.
Typ.
Max.
Units
3.135
3.3
3.465
V
(VDD/2)+1
V
(VDD/2)-1
2.0
V
V
0.8
VDD-0.5
V
V
0.5
2.4
V
V
0.4
V
IDD Operating Supply Current, 20
No load, 100M
20
mA
Short Circuit Current
CLK output
+70
mA
On-Chip Pull-up Resistor
Pin 7
270
kΩ
Input Capacitance, S1, S0, and OE
Pins 4, 6, 7
4
pF
20
Ω
Nominal Output Impedance
IDT™ LOCO™ PLL CLOCK MULTIPLIER
4
IDT5V40501
REV C 102808
IDT5V40501
LOCO™ PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
AC Electrical Characteristics
VDD = 3.3 V ±5%, Ambient Temperature -40 to +85° C, unless stated otherwise
Parameter
Symbol
Input Frequency, crystal input
FIN
Input Frequency, clock input
FIN
Output Frequency, VDD = 3.0 to 3.6 V
FOUT
Conditions
Min.
Typ.
Max. Units
5
27
MHz
See page 2
2
50
MHz
0° C to +70° C
13
100
MHz
-40° C to +85° C
13
90
MHz
Output Clock Rise Time
tOR
0.8 to 2.0 V, Note 1
1
ns
Output Clock Fall Time
tOF
2.0 to 8.0 V, Note 1
1
ns
Output Clock Duty Cycle
tOD
VDD/2
45
PLL Bandwidth
50
55
%
10
kHz
Output Enable Time, OE high to output
on
50
ns
Output Disable Time, OE low to tri-state
50
ns
Absolute Clock Period Jitter
tja
One Sigma Clock Period Jitter
tjs
Deviation from
mean
100
150
ps
15
ps
Note 1: Measured with 15 pF load.
Thermal Characteristics for 8SOIC
Parameter
Thermal Resistance Junction to
Ambient
Symbol
Conditions
Min.
Typ.
Max. Units
θJA
Still air
150
° C/W
θJA
1 m/s air flow
140
° C/W
θJA
3 m/s air flow
120
° C/W
40
° C/W
20
° C/W
Thermal Resistance Junction to Case
θJC
Thermal Resistance Junction to Top
of Case
ΨJT
Still air
Thermal Characteristics for 8MSOP
Parameter
Symbol
Thermal Resistance Junction to
Ambient
θJA
Thermal Resistance Junction to Case
θJC
IDT™ LOCO™ PLL CLOCK MULTIPLIER
Conditions
Still air
5
Min.
Typ.
Max. Units
95
° C/W
48
° C/W
IDT5V40501
REV C 102808
IDT5V40501
LOCO™ PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
Marking Diagrams (8-pin SOIC)
8
Marking Diagrams (8-pin MSOP)
5
IDT5V40
501DCG
#YYWW$
1
4
8
5
IDT5V40
501DVG
#YYWW$
IDT5V40
501DCGI
#YYWW$
1
IDT5V40
501DVGI
#YYWW$
4
Notes:
1. # = Z Stepping.
2. YYWW is the last two digits of the year and week that the part was assembled.
3. $ = assembler code.
4. “I” denotes industrial temperature.
5. “G” after the two-letter package code denotes RoHS compliant package.
IDT™ LOCO™ PLL CLOCK MULTIPLIER
6
IDT5V40501
REV C 102808
IDT5V40501
LOCO™ PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
Package Outline and Package Dimensions (8-pin MSOP, 3.00 mm Body)
Package dimensions are kept current with JEDEC Publication No. 95
Millimeters
8
Symbol
E1
A
A1
A2
b
C
D
E
E1
e
L
α
aaa
E
IN D E X
AREA
1
2
D
Min
Max
-1.10
0
0.15
0.79
0.97
0.22
0.38
0.08
0.23
3.00 BASIC
4.90 BASIC
3.00 BASIC
0.65 Basic
0.40
0.80
0°
8°
0.10
Inches*
Min
Max
-0.043
0
0.006
0.031
0.038
0.008
0.015
0.003
0.009
0.118 BASIC
0.193 BASIC
0.118 BASIC
0.0256 Basic
0.016
0.032
0°
8°
0.004
*For reference only. Controlling dimensions in mm.
A
2
A
A
1
c
-C e
b
S E A T IN G
P LA N E
L
aaa
IDT™ LOCO™ PLL CLOCK MULTIPLIER
C
7
IDT5V40501
REV C 102808
IDT5V40501
LOCO™ PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Narrow Body)
Package dimensions are kept current with JEDEC Publication No. 95
Millimeters
Symbol
8
E
A
A1
B
C
D
E
e
H
h
L
α
H
INDEX
AREA
1 2
D
Min
Inches*
Max
1.35
1.75
0.10
0.25
0.33
0.51
0.19
0.25
4.80
5.00
3.80
4.00
1.27 BASIC
5.80
6.20
0.25
0.50
0.40
1.27
0°
8°
Min
Max
.0532
.0688
.0040
.0098
.013
.020
.0075
.0098
.1890
.1968
.1497
.1574
0.050 BASIC
.2284
.2440
.010
.020
.016
.050
0°
8°
*For reference only. Controlling dimensions in mm.
A
h x 45
A1
C
-Ce
B
SEATING
PLANE
L
.10 (.004)
C
Ordering Information
Part / Order Number
Marking
Shipping Packaging
Package
Temperature
5V40501DCG
5V40501DCG8
5V40501DCGI
5V40501DCGI8
5V40501DVG
5V40501DVG8
5V40501DVGI
5V40501DVGI8
see page 6
Tubes
Tape and Reel
Tubes
Tape and Reel
Tubes
Tape and Reel
Tubes
Tape and Reel
8-pin SOIC
8-pin SOIC
8-pin SOIC
8-pin SOIC
8-pin MSOP
8-pin MSOP
8-pin MSOP
8-pin MSOP
0 to +70° C
0 to +70° C
-40 to +85° C
-40 to +85° C
0 to +70° C
0 to +70° C
-40 to +85° C
-40 to +85° C
Parts ordered with a “G” after the two-letter package code are the Pb-Free configuration and are RoHS compliant.
While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility
for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses
are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range,
high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to
change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical
instruments.
IDT™ LOCO™ PLL CLOCK MULTIPLIER
8
IDT5V40501
REV C 102808
IDT5V40501
LOCO™ PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
Innovate with IDT and accelerate your future networks. Contact:
www.IDT.com
For Sales
For Tech Support
800-345-7015
408-284-8200
Fax: 408-284-2775
www.idt.com/go/clockhelp
Corporate Headquarters
Integrated Device Technology, Inc.
www.idt.com
© 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device
Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered
trademarks used to identify products or services of their respective owners.
Printed in USA