TI1 BQ24156AYFFT Fully integrated switch-mode one-cell li-ion charger with full usb compliance and usb-otg support Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
bq2415x Fully Integrated Switch-Mode One-Cell Li-Ion Charger
With Full USB Compliance and USB-OTG Support
Not Recommended for New Designs bq24153A, bq24156A, bq24159
1 Features
•
•
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Charge Faster than Linear Chargers
High-Accuracy Voltage and Current Regulation
– Input Current Regulation Accuracy: ±5% (100
mA and 500 mA)
– Charge Voltage Regulation Accuracy: ±0.5%
(25°C), ±1% (0°C to 125°C)
– Charge Current Regulation Accuracy: ±5%
Input Voltage Based Dynamic Power
Management (VIN DPM)
Bad Adaptor Detection and Rejection
Safety Limit Register for Maximum Charge
Voltage and Current Limiting
High-Efficiency Mini-USB/AC Battery Charger for
Single-Cell Li-Ion and Li-Polymer Battery Packs
20-V Absolute Maximum Input Voltage Rating
9-V Maximum Operating Input Voltagebq24156A/9
6-V Maximum Operating Input Voltagebq24153A/8
Built-In Input Current Sensing and Limiting
Integrated Power FETs for Up To 1.55-A Charge
Rate
Programmable Charge Parameters through I2C™
Compatible Interface (up to 3.4 Mbps):
– Input Current Limit
– VIN DPM Threshold
– Fast-Charge/Termination Current
– Charge Regulation Voltage (3.5 V to 4.44 V)
– Low Charge Current Mode Enable/Disable
– Safety Timer with Reset Control
– Termination Enable/Disable
Support up to 1.55 A Charge Current Using 55mΩ Sensing Resistor
Synchronous Fixed-Frequency PWM Controller
Operating at 3 MHz With 0% to 99.5% Duty Cycle
Automatic High Impedance Mode for Low Power
Consumption
Robust Protection
– Reverse Leakage Protection Prevents Battery
Drainage
– Thermal Regulation and Protection
– Input/Output Overvoltage Protection
•
•
•
•
•
•
Status Output for Charging and Faults
USB Friendly Boot-Up Sequence
Automatic Charging
Power Up System without Battery bq24158/9
Boost Mode Operation for USB OTG:
(bq24153A/8 only)
– Input Voltage Range (from Battery): 2.5 V to
4.5 V
– Output for VBUS: 5.05 V/ 200 mA
2.1 mm x 2 mm 20-Pin WCSP Package
2 Applications
•
•
•
Mobile and Smart Phones
MP3 Players
Handheld Devices
3 Description
The bq24153A/6A/8/9 is a compact, flexible, highefficiency,
USB-friendly
switch-mode
charge
management device for single-cell Li-ion and Lipolymer batteries used in a wide range of portable
applications. The charge parameters can be
programmed through an I2C interface. The IC
integrates a synchronous PWM controller, power
MOSFETs, input current sensing, high-accuracy
current and voltage regulation, and charge
termination, into a small WCSP package.
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
bq24153A, bq24156A,
20-Pin WCSP
bq24158, bq24159
2.1 mm x 2 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Typical Application Circuit
VBUS
VBUS
1 µF
CIN
VAUX
PMID
4.7
µF
HOST
LO 1 µH
10 kΩ
CD
SCL
SDA
STAT
OTG
CD
10 kΩ
VSNS
22 µF
33 nF
BOOT
PGND
CO2
33 µF
CSIN
0.1 µF
CSOUT
VREF
VBAT
CO1
CBOOT
CSIN
10 kΩ 10 kΩ
SCL
SDA
STAT
OTG
10 kΩ
SW
U1
bq24153A/8
CIN
PACK+
+
PACK–
CVREF
CSOUT
0.1 µF
1 µF
Copyright © 2016, Texas Intruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. UNLESS OTHERWISE NOTED, this document contains PRODUCTION
DATA.
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Description (Continued) ........................................
Device Comparisons .............................................
Pin Configuration and Functions .........................
Specifications.........................................................
8.1
8.2
8.3
8.4
8.5
8.6
8.7
9
1
1
1
2
4
4
5
6
Absolute Maximum Ratings ..................................... 6
ESD Ratings ............................................................ 6
Recommended Operating Conditions....................... 6
Thermal Information .................................................. 6
Electrical Characteristics........................................... 7
Timing Requirements .............................................. 11
Typical Characteristics ............................................ 12
Detailed Description ............................................ 14
9.1
9.2
9.3
9.4
9.5
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
Programming ..........................................................
14
15
17
21
26
9.6 Register Maps ........................................................ 30
10 Application and Implementation........................ 34
10.1 Application Information.......................................... 34
10.2 Typical Application ................................................ 34
10.3 System Example ................................................... 39
11 Power Supply Recommendations ..................... 40
11.1 System Load After Sensing Resistor .................... 40
11.2 System Load Before Sensing Resistor ................. 41
12 Layout................................................................... 42
12.1 Layout Guidelines ................................................. 42
12.2 Layout Example .................................................... 43
13 Device and Documentation Support ................. 44
13.1
13.2
13.3
13.4
13.5
13.6
Third-Party Products Disclaimer ...........................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
44
44
44
44
44
44
14 Mechanical, Packaging, and Orderable
Information ........................................................... 45
14.1 Package Summary................................................ 45
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision C (July 2013) to Revision D
Page
•
Added the Device Information table, ESD Ratings table, Detailed Description section, Application and
Implementation section, Power Supply Recommendation section, Layout section, Device and Documentation
Support section, and the Mechanical, Packaging, and Orderable Information section.......................................................... 1
•
Changed Features bullet From: "...1.5-A Charge Rate" To: "...1.55-A Charge Rate" ............................................................ 1
•
Added Features bullet: "Support up to 1.55A......Sensing Resistor " ..................................................................................... 1
•
Added information to the Device Comparisons table. ............................................................................................................ 4
•
Changed t32S in the Timing Requirements table, PROTECTION section, MAX value From: 32s To 40s .......................... 11
•
Added information to bullet note at Table 9 for clarification. ............................................................................................... 33
Changes from Revision B (August 2012) to Revision C
Page
•
Changed Boot capacitor value from 10 nF to 33 nF in Typical Application Circuit ................................................................ 1
•
Changed BOOT capacitor value from 10 nF to 33 nF in Pin Functions Description.............................................................. 5
•
Changed CBOOT capacitor value from 10 nF to 33 nF in Figure 25 and Figure 36 .............................................................. 34
Changes from Revision A (February 2012) to Revision B
Page
•
Changed the revision to Rev B, August 2012 ........................................................................................................................ 1
•
Deleted the last sentence in the PIN Functions table: Name CD, in the description column ................................................ 5
•
Changed IO(CHARGE) Test Conditions statement from "V(LOWV)" to "V(SHORT)" ........................................................................... 7
•
Deleted from the CD Pin (Charge Disable) section the last sentence: In 15-minute....32-second timer. ............................ 24
2
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
Changes from Original (October 2010) to Revision A
Page
•
Added bq24159 throughout this data sheet. .......................................................................................................................... 1
•
Changed the Device Comparisons table ................................................................................................................................ 4
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
3
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
5 Description (Continued)
The IC charges the battery in three phases: conditioning, constant current and constant voltage. The input
current is automatically limited to the value set by the host. Charge is terminated based on battery voltage and
user-selectable minimum current level. A safety timer with reset control provides a safety backup for I2C
interface. During normal operation, The IC automatically restarts the charge cycle if the battery voltage falls
below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply
is removed. The charge status can be reported to the host using the I2C interface. During the charging process,
the IC monitors its junction temperature (TJ) and reduces the charge current once TJ increases to about 125°C.
To support USB OTG device, bq24153A/8 can provide VBUS (5.05 V) by boosting the battery voltage. The IC is
available in 20-pin WCSP package.
6 Device Comparisons
PART NUMBER
bq24153A
bq24156A
bq24158
6.5
9.8
6.5
9.8
OTG
SLRST
OTG
SLRST
ICHARGE(MAX) at POR in 15-minute mode with
R(SNS) = 68 mΩ (55 mΩ) and OTG=High on bq24153A/8
(mA)
325 (402)
325 (N/A)
325 (402)
325 (N/A)
ICHARGE(MAX) in HOST mode with R(SNS) = 68 mΩ (55 mΩ)
and Safety Limit Register increased from default (A) (1)
1.25 (1.55A)
1.55 (N/A)
1.25 (1.55A)
1.55(N/A)
1.55
N/A
1.55
N/A
3.54
3.54
3.54
3.54
Yes
No
Yes
No
500mA
100mA (OTG=LOW);
500mA (OTG=High)
500mA
VOVP (V)
D4 Pin Definition
Output regulation voltage at POR (V)
Boost Function
100mA (OTG=LOW);
500mA (OTG=High)
Input Current Limit in 15Min Mode
bq24159
Battery Detection at Power Up
Yes
Yes
No
No
I2C Address
6BH
6AH
6AH
6AH
PN1 (bit4 of 03H)
1
0
1
0
PN0 (bit3 of 03H)
0
0
0
0
Enabled
Enabled
Enabled
Enabled
Safety Timer and WD Timer
(1)
4
See Application Section for more explanation and calculations on using different sense resistors.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
7 Pin Configuration and Functions
YFF Package
20-Pin Bump DSBGA
bq24153A/8
(Top View)
bq24156A/9
(Top View)
A1
A2
A3
A4
A1
A2
A3
A4
VBUS
VBUS
BOOT
SCL
VBUS
VBUS
BOOT
SCL
B3
B4
B1
B3
B4
PMID
B1
PMID
B2
PMID
SDA
PMID
PMID
B2
PMID
SDA
C1
C2
C3
C4
C1
C2
C3
C4
SW
SW
SW
STAT
SW
SW
SW
STAT
D1
D2
D3
D4
D1
D2
D3
D4
PGND
PGND
PGND
OTG
PGND
PGND
PGND
SLRST
E1
E2
E3
E4
E1
E2
E3
E4
CD
VREF
CSOUT
CSIN
CD
VREF
CSOUT
CSIN
Pin Functions
PIN
I/O
DESCRIPTION
A3
I/O
Bootstrap capacitor connection for the high-side FET gate driver. Connect a 33-nF ceramic capacitor (voltage
rating ≥ 10 V) from BOOT pin to SW pin.
CD
E2
I
Charge disable control pin. CD=0, charge is enabled. CD=1, charge is disabled and VBUS pin is high
impedance to GND.
CSIN
E1
I
Charge current-sense input. Battery current is sensed across an external sense resistor. A 0.1-μF ceramic
capacitor to PGND is required.
CSOUT
E4
I
Battery voltage and current sense input. Bypass it with a ceramic capacitor (minimum 0.1 μF) to PGND if
there are long inductive leads to battery.
I
Boost mode enable control or input current limiting selection pin. When OTG is in active status, bq24153A/8
is forced to operate in boost mode. It has higher priority over I2C control and can be disabled using the
control register. At POR while in 15-min mode, the OTG pin is default to be used as the input current limiting
selection pin. The I2C register is ignored at startup. When OTG=High, IIN_LIMIT=500mA and when OTG=Low,
IIN_LIMIT=100mA.
NAME
NO.
BOOT
OTG
(bq24153A/8 only)
D4
PGND
D1, D2, D3
PMID
B1, B2, B3
I/O
SCL
A4
I
I2C interface clock. Connect a 10-kΩ pullup resistor to 1.8V rail (VAUX= VCC_HOST)
SDA
B4
I/O
I2C interface data. Connect a 10-kΩ pullup resistor to 1.8V rail (VAUX= VCC_HOST)
SLRST
(bq24156A/9 only)
D4
I
Safety limit register reset control. When SLRST=0, bq24156A/9 resets all the safety limits (06H) to default
values, regardless of the write actions to safety limits registers (06H). When SLRST=1, bq24156A/9 can
program the safety limit register until any write action to other registers locks the programmed safety limits.
STAT
C4
O
Charge status pin. Pull low when charge in progress. Open drain for other conditions. During faults, a 128-μs
pulse is sent out. STAT pin can be disabled by the EN_STAT bit in control register. STAT can be used to
drive a LED or communicate with a host processor.
C1, C2, C3
O
Internal switch to output inductor connection.
VBUS
A1, A2
I/O
Charger input voltage. Bypass it with a 1-μF ceramic capacitor from VBUS to PGND. It also provides power
to the load during boost mode (bq24153A/8 only) .
VREF
E3
O
Internal bias regulator voltage. Connect a 1µF ceramic capacitor from this output to PGND. External load on
VREF is not recommended.
SW
Power ground
Connection point between reverse blocking FET and high-side switching FET. Bypass it with a minimum of
3.3-μF capacitor from PMID to PGND.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
5
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
8 Specifications
8.1 Absolute Maximum Ratings (1)
(2)
over operating free-air temperature range (unless otherwise noted)
bq24153A/6A/8/9
MIN
MAX
UNIT
Supply voltage (with respect to PGND (3))
VBUS; VPMID ≥ VBUS –0.3 V
–2
20
V
Input voltage (with respect to PGND (3))
SCL, SDA, OTG, SLRST, CSIN, CSOUT, CD
–0.3
7
V
PMID, STAT
–0.3
20
V
7
V
–0.7
20
V
–7
7
V
–0.3
7
V
–7
0.7
V
–0.7
20
V
10
mA
Output voltage (with respect to PGND (3))
VREF
SW, BOOT
Voltage difference between CSIN and CSOUT inputs (V(CSIN) – V(CSOUT) )
Voltage difference between BOOT and SW inputs (V(BOOT) – V(SW) )
Voltage difference between VBUS and PMID inputs (V(VBUS) – V(PMID) )
Voltage difference between PMID and SW inputs (V(PMID) – V(SW) )
Output sink
STAT
Output Current (average)
SW
1.55 (2)
A
TA
Operating free-air temperature range
–30
85
°C
TJ
Junction temperature
–40
125
°C
Tstg
Storage temperature
–45
150
°C
(1)
(2)
(3)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage
values are with respect to the network ground terminal unless otherwise noted.
Duty cycle for output current should be less than 50% for 10- year life time when output current is above 1.25A.
All voltages are with respect to PGND if not specified. Currents are positive into, negative out of the specified terminal, if not specified.
Consult Packaging Section of the data sheet for thermal limitations and considerations of packages.
8.2 ESD Ratings
VALUE
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins
V(ESD)
(1)
(2)
Electrostatic discharge
(1)
UNIT
±2000
Charged device model (CDM), per JEDEC specification JESD22-C101,
all pins (2)
V
±500
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
8.3 Recommended Operating Conditions
MIN
NOM
MAX
UNIT
VBUS
Supply voltage, bq24153A/8
4
6 (1)
V
VBUS
Supply voltage, bq24156A/9
4
9 (1)
V
TJ
Operating junction temperature range
–40
125
°C
(1)
The inherent switching noise voltage spikes should not exceed the absolute maximum rating on either the BOOST or SW pins. A tight
layout minimizes switching noise.
8.4 Thermal Information
bq24153A/6A/8/9
THERMAL METRIC (1)
YFF (DSBGA)
UNIT
20 Pins
RθJA
Junction-to-ambient thermal resistance
85
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
25
°C/W
RθJB
Junction-to-board thermal resistance
55
°C/W
ψJT
Junction-to-top characterization parameter
4
°C/W
ψJB
Junction-to-board characterization parameter
50
°C/W
(1)
6
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
Thermal Information (continued)
bq24153A/6A/8/9
THERMAL METRIC (1)
YFF (DSBGA)
UNIT
20 Pins
RθJC(bot)
Junction-to-case (bottom) thermal resistance
n/a
°C/W
8.5 Electrical Characteristics
Circuit of Figure 25, VBUS = 5 V, HZ_MODE = 0, OPA_MODE = 0 (CD = 0), TJ = –40°C to 125°C, TJ = 25°C for typical
values (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
INPUT CURRENTS
VBUS > VBUS(min), PWM switching
I(VBUS)
VBUS supply current control
10
VBUS > VBUS(min), PWM NOT switching
23
μA
Leakage current from battery to VBUS pin
0°C < TJ < 85°C, V(CSOUT) = 4.2 V, High Impedance
mode, VBUS = 0 V
5
μA
Battery discharge current in High Impedance
mode, (CSIN, CSOUT, SW pins)
0°C < TJ < 85°C, V(CSOUT) = 4.2 V, High Impedance
mode, V = 0 V, SCL, SDA, OTG = 0 V
or 1.8 V
23
μA
V
0°C < TJ < 85°C, CD=1 or HZ_MODE=1
Ilgk
mA
5
15
VOLTAGE REGULATION
V(OREG)
Output regulation voltage programable range
Operating in voltage regulation, programmable
TA = 25°C
Voltage regulation accuracy
3.5
4.44
–0.5%
0.5%
–1%
1%
CURRENT REGULATION (FAST CHARGE)
IO(CHARGE)
Output charge current programmable range
bq24153A/8, V(SHORT) ≤ V(CSOUT) < V(OREG),
VBUS > V(SLP), R(SNS) = 68 mΩ, LOW_CHG=0,
Programmable
550
bq24156A/9, V(SHORT) ≤ V(CSOUT) < V(OREG),
VBUS > V(SLP), R(SNS) = 68 mΩ, LOW_CHG=0,
Programmable
550
VSHORT ≤ VCSOUT < VOREG, VBUS >VSLP,
Low charge current (default after POR in 15 min
RSNS= 68 mΩ, LOW_CHG=1, OTG=High for
mode) for bq24153A/6A/8/9
bq24153A/8
Regulation accuracy of the voltage across
R(SNS) (for charge current regulation)
V(IREG) = IO(CHARGE) × R(SNS)
325
37.4 mV ≤ V(IREG)< 44.2mV
44.2 mV ≤ V(IREG)
1250
mA
1550
mA
350
mA
–3.5%
3.5%
–3%
3%
3.4
3.7
WEAK BATTERY DETECTION
V(LOWV)
Weak battery voltage threshold programmable
range2 (1)
Adjustable using I2C control
Weak battery voltage accuracy
Hysteresis for V(LOWV)
–5%
Battery voltage falling
V
5%
100
mV
CD, OTG and SLRST PIN LOGIC LEVEL
VIL
Input low threshold level
VIH
Input high threshold level
I(bias)
Input bias current
0.4
V
1.0
µA
1.3
V
Voltage on control pin is 5 V
CHARGE TERMINATION DETECTION
I(TERM)
Termination charge current programmable
range
Regulation accuracy for termination current
across R(SNS)
V(IREG_TERM) = IO(TERM) × R(SNS)
V(CSOUT) > V(OREG) – V(RCH),
VBUS > V(SLP), R(SNS) = 68 mΩ, Programmable
3.4 mV ≤ V(IREG_TERM) ≤ 6.8 mV
50
400
–15%
15%
6.8 mV < V(IREG_TERM) ≤ 17 mV
–10%
10%
17 mV < V(IREG_TERM) ≤ 27.2 mV
–5.5%
5.5%
mA
BAD ADAPTOR DETECTION
VIN(min)
ISHORT
(1)
Input voltage lower limit
BAD ADAPTOR DETECTION
3.6
Hysteresis for VIN(min)
Input voltage rising
100
Current source to GND
During bad adaptor detection
20
3.8
30
4.0
V
200
mV
40
mA
While in 15-min mode, if a battery that is charged to a voltage higher than this voltage is inserted, the charger enters Hi-Z mode and
awaits I2C commands.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
7
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
Electrical Characteristics (continued)
Circuit of Figure 25, VBUS = 5 V, HZ_MODE = 0, OPA_MODE = 0 (CD = 0), TJ = –40°C to 125°C, TJ = 25°C for typical
values (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
INPUT BASED DYNAMIC POWER MANAGEMENT
VIN_DPM
Input Voltage DPM threshold programmable
range
VIN DPM threshold accuracy
8
Submit Documentation Feedback
4.2
4.76
–3%
1%
V
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
Electrical Characteristics (continued)
Circuit of Figure 25, VBUS = 5 V, HZ_MODE = 0, OPA_MODE = 0 (CD = 0), TJ = –40°C to 125°C, TJ = 25°C for typical
values (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
TJ = 0°C – 125°C
88
93
98
TJ = –40°C –125°C
86
93
98
TJ = 0°C – 125°C
450
475
500
TJ = –40°C –125°C
440
475
500
UNIT
INPUT CURRENT LIMITING
IIN = 100 mA
IIN_LIMIT
Input current limiting threshold
IIN = 500 mA
mA
mA
VREF BIAS REGULATOR
VREF
Internal bias regulator voltage
VBUS >VIN(min) or V(CSOUT) > VBUS(min),
I(VREF) = 1 mA, C(VREF) = 1 μF
2
VREF output short current limit
6.5
30
V
mA
BATTERY RECHARGE THRESHOLD
V(RCH)
Recharge threshold voltage
Below V(OREG)
100
120
150
mV
STAT OUTPUTS
VOL(STAT)
Low-level output saturation voltage, STAT pin
IO = 10 mA, sink current
High-level leakage current for STAT
Voltage on STAT pin is 5 V
0.55
V
1
μA
I2C BUS LOGIC LEVELS AND TIMING CHARACTERISTICS
VOL
Output low threshold level
IO = 10 mA, sink current
0.4
V
VIL
Input low threshold level
V(pull-up) = 1.8 V, SDA and SCL
0.4
V
VIH
Input high threshold level
V(pull-up) = 1.8 V, SDA and SCL
I(BIAS)
Input bias current
V(pull-up) = 1.8 V, SDA and SCL
1
μA
f(SCL)
SCL clock frequency
1.2
V
3.4
MHz
BATTERY DETECTION
I(DETECT)
Battery detection current before charge done
(sink current) (2)
Begins after termination detected,
V(CSOUT) ≤ V(OREG)
–0.5
mA
SLEEP COMPARATOR
V(SLP)
Sleep-mode entry threshold,
VBUS – VCSOUT
2.3 V ≤ V(CSOUT) ≤ V(OREG), VBUS falling
V(SLP_EXIT)
Sleep-mode exit hysteresis
0
40
100
mV
2.3 V ≤ V(CSOUT) ≤ V(OREG)
140
200
260
mV
3.55
UNDERVOLTAGE LOCKOUT (UVLO)
UVLO
IC active threshold voltage
VBUS rising - Exits UVLO
3.05
3.3
UVLO(HYS)
IC active hysteresis
VBUS falling below UVLO - Enters UVLO
120
150
Voltage from BOOT pin to SW pin
During charge or boost operation
Internal top reverse blocking MOSFET onresistance
IIN(LIMIT) = 500 mA, Measured from VBUS to PMID
180
250
Internal top N-channel Switching MOSFET onresistance
Measured from PMID to SW,
VBOOT – VSW= 4V
120
250
Internal bottom N-channel MOSFET onresistance
Measured from SW to PGND
110
210
V
mV
PWM
f(OSC)
6.5
Oscillator frequency
3.0
Frequency accuracy
D(MAX)
Maximum duty cycle
D(MIN)
Minimum duty cycle
–10%
mΩ
MHz
10%
99.5%
0
Synchronous mode to non-synchronous mode
transition current threshold (2)
(2)
V
Low-side MOSFET cycle-by-cycle current sensing
100
mA
Bottom N-channel FET always turns on for ~30 ns and then turns off if current is too low.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
9
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
Electrical Characteristics (continued)
Circuit of Figure 25, VBUS = 5 V, HZ_MODE = 0, OPA_MODE = 0 (CD = 0), TJ = –40°C to 125°C, TJ = 25°C for typical
values (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
6.3
6.5
6.7
UNIT
CHARGE MODE PROTECTION
VOVP_IN_USB
VOVP-IN_DYN
VOVP
ILIMIT
VSHORT
ISHORT
Input VBUS OVP threshold voltage
(bq24153A/8)
VBUS threshold to turn off converter during charge
V(OVP_IN_USB) hysteresis (bq24153A/8)
VBUS falling from above V(OVP_IN_USB)
Input VBUS OVP threshold voltage (bq24156A)
Threshold over VBUS to turn off converter during
charge
V(OVP_IN_DYN) hysteresis (bq24156A/9)
VBUS falling from above V(OVP_IN_DYN)
Output OVP threshold voltage
V(CSOUT) threshold over V(OREG) to turn off charger
during charge
V(OVP) hysteresis
Lower limit for V(CSOUT) falling from above V(OVP)
Cycle-by-cycle current limit for charge
Charge mode operation
1.8
2.4
3.0
Trickle to fast charge threshold
V(CSOUT) rising
2.0
2.1
2.2
VSHORT hysteresis
V(CSOUT) falling below VSHORT
Trickle charge charging current
V(CSOUT) ≤ VSHORT)
170
9.57
9.8
V
mV
10
140
110
117
121
%V OREG
11
100
20
30
A
V
mV
40
mA
BOOST MODE OPERATION FOR VBUS (OPA_MODE = 1, HZ_MODE = 0, bq24153A/8 only)
VBUS_B
Boost output voltage (to VBUS pin)
2.5V < V(CSOUT) < 4.5 V
5.05
Boost output voltage accuracy
Including line and load regulation
IBO
Maximum output current for boost
VBUS_B = 5.05 V, 2.5 V < V(CSOUT) < 4.5 V
IBLIMIT
Cycle by cycle current limit for boost
VBUS_B = 5.05 V, 2.5 V < V(CSOUT) < 4.5 V
VBUSOVP
Overvoltage protection threshold for boost
(VBUS pin)
Threshold over VBUS to turn off converter during
boost
VBUSOVP hysteresis
VBUS falling from above VBUSOVP
Maximum battery voltage for boost (CSOUT
pin)
V(CSOUT) rising edge during boost
VBATMAX hysteresis
V(CSOUT) falling from above VBATMAX
200
During boosting
2.5
Before boost starts
2.9
VBATMAX
VBATMIN
Minimum battery voltage for boost (CSOUT pin)
Boost output resistance at high-impedance
mode (From VBUS to PGND)
–3%
V
3%
200
mA
1.0
5.8
6.0
A
6.2
162
4.75
CD = 1 or HZ_MODE = 1
4.9
217
V
mV
5.05
V
mV
V
3.05
V
kΩ
PROTECTION
TSHTDWN)
Thermal trip
165
Thermal hysteresis
TCF
10
10
Thermal regulation threshold
Charge current begins to reduce
Submit Documentation Feedback
°C
120
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
8.6 Timing Requirements
MIN
NOM
MAX
UNIT
WEAK BATTERY DETECTION
Deglitch time for weak battery
threshold
Rising voltage, 2-mV over drive,
tRISE = 100 ns
30
ms
Both rising and falling, 2-mV
overdrive,
tRISE, tFALL = 100 ns
30
ms
Deglitch time for VBUS rising above
VIN(min)
Rising voltage, 2-mV overdrive,
tRISE = 100 ns
30
ms
Detection Interval
Input power source detection
2
s
CHARGE TERMINATION DETECTION
Deglitch time for charge termination
BAD ADAPTER DETECTION
tINT
BATTERY RECHARGE THRESHOLD
V(SCOUT) decreasing below
threshold,
tFALL = 100 ns, 10-mV overdrive
Deglitch time
130
ms
262
ms
30
ms
140
ms
BATTERY DETECTION
tDETECT
Battery detection time
SLEEP COMPARATOR
Deglitch time for VBUS rising above
V(SLP) + V(SLP_EXIT)
Rising voltage, 2-mV overdrive,
tRISE = 100 ns
UNDERVOLTAGE LOCKOUT (UVLO)
Power up delay
PROTECTION
t32S
32 second watchdog (WD) timer
32 Second or HOST mode
15
t15M
15 minute safety timer
15 Minute mode
12
Copyright © 2010–2016, Texas Instruments Incorporated
32
40
s
15
m
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
11
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
8.7 Typical Characteristics
Using circuit shown in Figure 25, TA = 25°C, unless otherwise specified.
VSW
2 V/div
VSW
2 V/div
IL
0.5 A/div
IL
0.5 A/div
100 nS/div
2 ms/div
VBUS = 5V,
VBAT = 3.5V
Charge Mode
Overload Operation
VBUS = 5 V,
ICHG = 1550 mA
VBAT = 2.6 V,
Voreg = 4.2 V,
Figure 2. PWM Charging Waveforms
Figure 1. Cycle by Cycle Current Limiting in Charge Mode
VSW
5 V/div
VBUS
2 V/div
VSW
2 V/div
IBUS
20 mA/div
IBAT
200 mA/div
500 mS/div
10 ms/div
VBUS = 5 V at 8 mA,
ICHG = 550 mA
VBAT = 3.2V,
Iin_limit = 100 mA,
Vin = 5 V,
ICHG = 1550mA
Figure 3. Poor Source Detection
VBAT = 3. 2V,
No Input Current Limit,
Figure 4. Charge Current Ramp Up
VBUS
1 V/div
OTG
2 V/div
15 Minute Mode
32 S Mode
IBUS
0.2 A/div
IBAT
0.1 A/div
Write Command
0.5 mS/div
1 S/div
VBUS = 5 V, VBAT = 3.1V, Iin_limit = 100/500 mA,
(OTG Control, 15 Minute Mode), Iin_limit = 100 mA
(I2C Control, 32 Second Mode)
Figure 5. Input Current Control (bq24153A/8)
12
Submit Documentation Feedback
VBUS = 5 V at 500 mA, VBAT = 3.5V, ICHG = 1550 mA,
VIN_DPM = 4.52 V
space
Figure 6. VIN Based DPM
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
Typical Characteristics (continued)
94
93
VBUS
2 V/div
Vbat = 4.2 V
92
Vbat = 3.6 V
91
Efficiency - %
90
89
VPMID
200 mV/div,
5.02 V Offset
88
VSW
5 V/div
87
86
85
Vbat = 3 V
84
IBUS
0.2 A/div
83
82
81
5 mS/div
80
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
Charge Current - A
1.1 1.2 1.3 1.4 1.5
VBUS = 5.05 V,
VBAT = 3.5V,
RLOAD (at VBUS) = 1kΩ
to 0.5Ω
Figure 8. VBUS Overload Waveforms (BOOST Mode)
Figure 7. Charger Efficiency
95
VBUS
0.5 V/div,
4.5 V Offset
90
Efficiency (%)
OTG
2 V/div
VSW
5 V/div
85
80
VBAT = 2.7 V
75
VBAT = 3.6 V
IL
0.5 A/div
VBAT = 4.2 V
70
0
50
100
150
200
Load Current at VBUS (mA)
10 mS/div
space
VBUS = 4.5 V (Charge Mode) / 5.1 V
(Boost Mode), VBAT = 3.5V, IIN_LIM = 500 mA, (32S mode)
Figure 10. BOOST Efficiency
Figure 9. BOOST to Charge Mode Transition (OTG Control)
5.09
5.08
IBUS = 200 mA
5.08
5.07
5.07
5.06
IBUS = 50 mA
VBUS
VBUS - V
5.06
5.05
5.04
5.05
5.04
IBUS = 100 mA
5.03
5.03
5.02
5.02
VBAT = 2.7 V
5.01
VBAT = 3.6 V
VBAT = 4.2 V
5
5.01
2.6
2.8
3
3.2
3.4
3.6
3.8
4
VBAT - V
Figure 11. Line Regulation for BOOST
Copyright © 2010–2016, Texas Instruments Incorporated
4.2
0
50
100
150
200
Load Current at VBUS (mA)
Figure 12. Line Regulation for Boost
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
13
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
9 Detailed Description
9.1 Overview
For a current restricted power source, such as a USB host or hub, a high efficiency converter is critical to fully
use the input power capacity for quickly charging the battery. Due to the high efficiency for a wide range of input
voltages and battery voltages, the switch mode charger is a good choice for high speed charging with less power
loss and better thermal management than a linear charger.
The bq24153A/8/9 are highly integrated synchronous switch-mode chargers, featuring integrated FETs and small
external components, targeted at extremely space-limited portable applications powered by 1-cell Li-Ion or Lipolymer battery pack. Furthermore, bq24153A/8 also has bi-directional operation to achieve boost function for
USB OTG support.
The bq24153A/8 have three operation modes: charge mode, boost mode, and high impedance mode, while the
bq24156A/9 only has charge mode and high impedance mode. In charge mode, the IC supports a precision Liion or Li-polymer charging system for single-cell applications. In boost mode, the IC boosts the battery voltage to
VBUS for powering attached OTG devices. In high impedance mode, the IC stops charging or boosting and
operates in a mode with very low current from VBUS or battery, to effectively reduce the power consumption
when the portable device is in standby mode. Through I2C communication with a host, referred to as "HOST or
32-second" control/mode, the IC achieves smooth transition among the different operation modes. Even when no
I2C communication is available, the IC starts a 15 minute saftey timer and enters "15-minute" (default) mode.
During 15-minute operation, the charger will still charge the battery but using each register's default values.
14
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
9.2 Functional Block Diagram
PMID
bq24153A/6A/8/9
PMID
V PMID
PMID
NMOS
VBUS
NMOS
SW
VBUS
VBUS
SW
Q2
Q1
VREF 1
OSC
Charge
Pump
-
PWM
Controller
CBC
Current
Limiting
Q3
I LIMIT
-
-
I IN _ LIMIT
-
T CF
+
TJ
-
V BUS
+
V UVLO
-
V BUS
+
V IN(MIN)
-
VBUS
+
V OVP_IN
-
TJ
+
VOUT
+
V OVP
-
V CSIN
+
-
CSIN
IOCHARGE
VREF
I SHORT
PWM _ CHG
VBUS UVLO
LINEAR
Poor Input
Source
Thermal
Shutdown
*
_CHG
VREF
REFERNCES
& BIAS
VBUS OVP
-
T SHTDWN
CSOUT
V OREG
-
+
V IN _ DPM
V OUT
+
+
SW
NMOS
CHARGE CONTROL
TIMER and DISPLAY
LOGIC
VREF
BOOT
VREF 1
V PMID
VOUT
Battery OVP
STAT
V BAT
VBUS
VOREG - VRCH
PGND
PGND
VOUT
VOUT
VCSIN
I TERM
+
-
*
Sleep
CD
+
-
+
-
* Recharge
*
PGND
VBAT
+
VSHORT
-
OTG (bq 24153 /8)
SLRST(bq24156)
Termination
( I2 C Control )
Decoder
DAC
SCL
SDA
Charge
* PWMMode
* Signal Deglitched
Copyright © 2016, Texas Intruments Incorporated
Figure 13. Function Block Diagram of bq2415x in Charge Mode
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
15
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
Functional Block Diagram (continued)
PMID
bq24153A/8
PMID
V PMID
PMID
NMOS
VBUS
NMOS
SW
SW
SW
V BUS
VBUS
Q2
Q1
VREF 1
Charge
Pump
OSC
PWM
Controller
CBC
Current
Limiting
Q3
PFM Mode
I BO
-
+
+
VBUS_B
+
I BLIMIT
V BUS
+
-
TJ
+
TSHTDWN
-
VOUT
+
VBATMAX
-
75 mA
-
VREF
REFERNCES
& BIAS
PWM _ BOOST
V BUSOVP
NMOS
VBUS OVP
VREF
BOOT
VREF 1
VPMID
CSIN
Thermal
Shutdown
*
Battery OVP
V OUT
CHARGE CONTROL,
TIMER and DISPLAY
LOGIC
CSOUT
STAT
CD
PGND
PGND
V BAT
+
VBATMIN
-
*
*
Low Battery
OTG
( I2 C Control)
Decoder
DAC
Signal Deglitched
PGND
SCL
SDA
Copyright © 2016, Texas Intruments Incorporated
Figure 14. Function Block Diagram of bq2415x in Boost Mode
16
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
9.3 Feature Description
9.3.1 Input Voltage Protection
9.3.1.1 Input Overvoltage Protection
The IC provides a built-in input overvoltage protection to protect the device and other components against
damage if the input voltage (Voltage from VBUS to PGND) goes too high. When an input overvoltage condition is
detected, the IC turns off the PWM converter, sets fault status bits, and sends out a fault pulse from the STAT
pin. Once VBUS drops below the input overvoltage exit threshold, the fault is cleared and charge process
resumes.
9.3.1.2 Bad Adaptor Detection/Rejection
Although not shown in Figure 26, at power-on-reset (POR) of VBUS, the IC performs the bad adaptor detection
by applying a current sink to VBUS. If the VBUS is higher than VIN(MIN) for 30ms, the adaptor is good and the
charge process begins. Otherwise, if the VBUS drops below VIN(MIN), a bad adaptor is detected. Then, the IC
disables the current sink, sends a send fault pulse in FAULT pin and sets the bad adaptor flag (B2 - B0 = 011 for
Register 00H). After a delay of TINT, the IC repeats the adaptor detection process, as shown in Figure 15 and
Figure 16.
Adpator
V BUS
VBUS
ISHORT
(30 mA)
Adaptor Detection Control
VIN_GOOD
Deglitch
30ms
PGND
GND
START
VIN
VIN(MIN)
VIN_POOR
Delay
TINT
Figure 15. Bad Adaptor Detection Circuit
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
17
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
Feature Description (continued)
Charge Command
(Host Control or VBUS
Ramps Up)
Delay 10mS
Enable Adaptor Detection
Start 30ms Timer
Enable Input Current Sink
(30mA, to GND)
No
VBUS>VIN(MIN)?
No
Yes
30ms Timer
Expired?
Yes
Bad Adaptor Detected
Good Adaptor Detected
Pulsing STAT Pin
Set Bad Adaptor Flag
Disable Adaptor Detection
Charge Start
Enable VIN Based DPM
Delay TINT
(2 Seconds)
Figure 16. Bad Adaptor Detection Scheme Flow Chart
9.3.1.3 Sleep Mode
The IC enters the low-power sleep mode if the VBUS pin voltage falls below the sleep-mode entry threshold,
VCSOUT+VSLP, and VBUS is higher than the bad adaptor detection threshold, VIN(MIN). This feature prevents
draining the battery during the absence of VBUS. During sleep mode, both the reverse blocking switch Q1 and
PWM are turned off.
9.3.1.4 Input Voltage Based DPM (Special Charger Voltage Threshold)
During the charging process, if the input power source is not able to support the programmed or default charging
current, the VBUS voltage will decrease. Once the VBUS drops to VIN_DPM (default 4.52V), the charge current
begins to taper down to prevent any further drop of VBUS. When the IC enters this mode, the charge current is
lower than the set value and the special charger bit is set (B4 in Register 05H). This feature makes the IC
compatible with adapters having different current capabilities.
9.3.2 Battery Protection
9.3.2.1 Output Overvoltage Protection
The IC provides a built-in overvoltage protection to protect the device and other components against damage if
the battery voltage goes too high, as when the battery is suddenly removed. When an overvoltage condition is
detected, the IC turns off the PWM converter, sets fault status bits, and sends out a fault pulse from the STAT
pin. Once V(CSOUT) drops to the battery overvoltage exit threshold, the fault is cleared and charge process
resumes.
18
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
Feature Description (continued)
9.3.2.2 Battery Short Protection
During the normal charging process, if the battery voltage is lower than the short-circuit threshold, VSHORT, the
charger operates in short circuit mode with a lower charge rate of ISHORT.
9.3.2.3 Battery Detection at Power Up in 15-minute Mode (bq24153A/6A only)
bq24153A/6A also have a unique battery detection scheme during the start up of the charger. At VBUS power
up, if the timer is in 15-minute mode, bq24153A/6A will start a 262ms timer when exiting from short circuit mode
to PWM charge mode. If the battery voltage is charged above the recharge threshold (VOREG-VRCH) when the
262ms timer expired, bq2153A/6A will not consider the battery present; then stop charging, and go to high
impedance mode immediately. However, if the battery voltage is still below the recharge threshold when the
262ms timer expires, the charging process will continue as normal battery charging process.
bq24158/9 simply begin regulating the output voltage to their default values (3.54V) at power up while in 15minute mode.
9.3.2.4 Battery Detection in Host Mode
For applications with removable battery packs, the IC provides a battery absent detection scheme to reliably
detect insertion or removal of battery packs.
During the normal charging process with host control, once the voltage at the CSOUT pin is above the battery
recharge threshold, VOREG - VRCH, and the termination charge current is detected, the IC turns off the PWM
charge and enables a discharge current, IDETECT, for a period of tDETECT, (262 ms typical) then checks the battery
voltage. If the battery voltage is still above the recharge threshold after tDETECT, the battery is present. On the
other hand, if the battery voltage is below the battery recharge threshold, the battery is absent. Under this
condition, the charge parameters (such as input current limit) are reset to the default values and charge resumes
after a delay of TINT. This function ensures that the charge parameters are reset whenever the battery is
replaced.
9.3.3 15-Minute Safety Timer and 32-second Watchdog Timer in Charge Mode
Once a good adapter and good battery are attached, the IC starts the 15-minute saftey timer (t15min) that can be
disabled by any write-action performed by host through I2C interface. Once the 15-minute timer is disabled, a 32second watchdog timer (t32sec) is automatically started. The 32-second timer can be reset by the host using I2C
interface. Writing “1” to reset the TMR_RST bit in the control register will reset the 32-second timer and
TMR_RST is automatically set to “0” after the 32-second timer is reset. If the 32-second timer expires, the charge
is terminated and charge parameters are reset to default values. Then the 15-minute timer starts and the charge
resumes in 15-minute mode.
During normal charging process, the IC is usually in 32-second mode with host control and 15-minute mode
without host control using I2C interface. The above process repeats until the battery is fully charged. If the 15minute timer expires, the IC turns off the charge, enunciates FAULT on the STATx bits of status register, and
sends the 128μs interrupt pulse. This function prevents battery over charge if the host fails to reset the safety
timer. The 15-minute charge, with default parameters, allows time for a discharged battery to charge sufficiently
to be able to power the host and start communication. The safety timer flow chart is shown in Figure 17. Fault
condition is cleared by POR and fault status bits can only be updated after the status bits are read by the host.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
19
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
Feature Description (continued)
Charge Start
Start T15 min
Timer
Reset Charge
Parameters
Yes
No
T 32 sec Expired ?
Start T32 sec
Stop T15 min
No
Yes
Charge
2
T 15 min Active ?
Yes
Any I C Write Action ?
No
T 15 min
Expired ?
No
Host Should Reset
T 32 sec Timer
Yes
Timer Fault
Figure 17. Timer Flow Chart for bq24153A/6A/8/9
9.3.4 USB Friendly Power Up
Prior to POR, if the host continues to write the TMR_RST bit to 1, to stay in 32-second mode, then at POR, the
charger enters normal charge mode (using the desired control bits). If not in 32-second mode at POR, the charge
will operate with default bit values, in 15 minute mode, until the host updates the control registers.
If the battery voltage is above the VLOWV threshold while in 15 minute mode, the charger will be in the high
impedance state. The default control bits set the charging current and regulation voltage low as a safety feature
to avoid violating USB spec and over-charging any of the Li-Ion chemistries, while the host has lost
communication. The input current limiting is described below.
9.3.5 Input Current Limiting at Power Up
The input current sensing circuit and control loop are integrated into the IC. When operating in 15-minute mode,
for bq24153A/8, the OTG pin logic level sets the input current limit to 100mA for a logic low and 500mA for a
logic high, whereas the bq24156A/9 defaults to 500mA. In 32 second mode, the input current limit is set by the
programmed control bits in register 01H.
20
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
9.4 Device Functional Modes
9.4.1 Charge Mode Operation
Power Up
V BUS > V UVLO
V
POR
Load I 2 C Registers
with Default Value
CSOUT
< V LOWV
High Impedance Mode or Host
No
Controlled Operation Mode
Yes
Reset and Start
15-M inute T imer
Disable Charge
/CE = LOW
/CE = HIGH
Charge Configure
Mode
Any Charge State
Disable Charge
Wait Mode
Delay TINT
Indicate Power
not Good
Yes
No
Enable I SHORT
V CSOPUT <V SHORT ?
Yes
V BUS < V IN ( MIN ) ?
Indicate Short
Circuit condition
No
15- Minute
Timer Expired ?
No
Regulate
Input Current , Charge
Current or Voltage
Yes
Indicate Charge- In Progress
VBUS < V IN ( MIN ) ?
Yes
Yes
Turn Off Charge
Indicate Fault
Yes
/CE =HIGH
No
Turn Off Charge
No
Enable I DETECT for
t DETECT
15-Minute
Timer Expired ?
Battery Removed
No
V CSOUT < VOREG V RCH ?
Yes
Wait Mode
Delay T INT
Reset Charge
Parameters
Yes
No
VCSOUT < V SHORT ?
No
Charge Complete
15-Minute Timer
Active ?
No
Yes
Termination Enabled
I TERM detected
and VCSOUT >V OREG -V RCH
?
Indicate DONE
No
Yes
Charge Complete
V CSOUT < V OREG VRCH ?
High Impedance
Mode
Yes
Figure 18. Operational Flow Chart of bq2415x in Charge Mode
9.4.1.1 Charge Profile
Once a good battery with voltage below the recharge threshold has been inserted and a good adapter is
attached, the bq2415x enters charge mode. In charge mode, the IC has five control loops to regulate input
voltage, input current, charge current, charge voltage and device junction temperature. During the charging
process, all five loops are enabled and the one that is dominant takes control. The IC supports a precision Li-ion
or Li-polymer charging system for single-cell applications. (a) indicates a typical charge profile without input
current regulation loop. It is the traditional CC/CV charge curve, while (b) shows a typical charge profile when
input current limiting loop is dominant during the constant current mode. In this case, the charge current is higher
than the input current so the charge process is faster than the linear chargers. For bq24153A/6A/8/9, the input
voltage threshold for DPM loop, input current limits, the charge current, termination current, and charge voltage
are all programmable using I2C interface.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
21
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
Device Functional Modes (continued)
Precharge
Phase
Current Regulation
Phase
Voltage Regulation
Phase
Regulation
Voltage
Regulation
Current
Charge Voltage
V SHORT
Charge Current
Termination
I SHORT
Precharge
(Linear Charge)
Precharge
Phase
Fast Charge
(PWM Charge)
(a)
Current Regulation
Phase
Voltage Regulation
Phase
Regulation
voltage
Charge Voltage
VSHORT
Charge Current
Termination
I SHORT
Precharge
(Linear Charge)
Fast Charge
(PWM Charge)
(b)
Figure 19. Typical Charging Profile of bq24153A/6A/8/9 for
(a) without Input Current Limit, and (b) with Input Current Limit
22
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
Device Functional Modes (continued)
9.4.2 PWM Controller in Charge Mode
The IC provides an integrated, fixed 3 MHz frequency voltage-mode controller to regulate charge current or
voltage. This type of controller is used to improve line transient response, thereby, simplifying the compensation
network used for both continuous and discontinuous current conduction operation. The voltage and current loops
are internally compensated using a Type-III compensation scheme that provides enough phase margin for stable
operation, allowing the use of small ceramic capacitors with a low ESR. The device operates between 0% to
99.5% duty cycles.
The IC has back to back common-drain N-channel FETs at the high side and one N-channel FET at low side.
The input N-FET (Q1) prevents battery discharge when VBUS is lower than VCSOUT. The second high-side N-FET
(Q2) is the switching control switch. A charge pump circuit is used to provide gate drive for Q1, while a bootstrap
circuit with an external bootstrap capacitor is used to supply the gate drive voltage for Q2.
Cycle-by-cycle current limit is sensed through the FETs Q2 and Q3. The threshold for Q2 is set to a nominal 2.4A peak current. The low-side FET (Q3) also has a current limit that decides if the PWM Controller will operate in
synchronous or non-synchronous mode. This threshold is set to 100mA and it turns off the low-side N-channel
FET (Q3) before the current reverses, preventing the battery from discharging. Synchronous operation is used
when the current of the low-side FET is greater than 100mA to minimize power losses.
9.4.3 Battery Charging Process
At the beginning of precharge, while battery voltage is below the V(SHORT) threshold, the IC applies a short-circuit
current, I(SHORT), to the battery. When the battery voltage is above VSHORT and below VOREG, the charge current
ramps up to fast charge current, IOCHARGE, or a charge current that corresponds to the input current of IIN_LIMIT.
The slew rate for fast charge current is controlled to minimize the current and voltage over-shoot during transient.
Both the input current limit, IIN_LIMIT, and fast charge current, IOCHARGE, can be set by the host. Once the battery
voltage reaches the regulation voltage, VOREG, the charge current is tapered down as shown in . The voltage
regulation feedback occurs by monitoring the battery-pack voltage between the CSOUT and PGND pins. In
HOST mode, the regulation voltage is adjustable (3.5V to 4.44V) and is programmed through I2C interface. In 15minute mode, the regulation voltage is fixed at 3.54V.
The IC monitors the charging current during the voltage regulation phase. If termination is enabled, during the
normal charging process with HOST control, once the voltage at the CSOUT pin is above the battery recharge
threshold, VOREG - VRCH for the 32-ms (typical) deglitch period, and the termination charge current ITERM is
detected, the IC turns off the PWM charge and enables a discharge current, IDETECT, for a period of tDETECT (262ms typical), then checks the battery voltage. If the battery voltage is still above the recharge threshold after
tDETECT, the battery charging is complete. The battery detection routine is used to ensure termination did not
occur because the battery was removed. After 40ms (typical) for synchronization purposes of the EOC state and
the counter, the status bit and pin are updated to indicate charging has completed. The termination current level
is programmable. To disable the charge current termination, the host can set the charge termination bit (I_Term)
of charge control register to 0, refer to I2C section for detail.
A
•
•
•
new charge cycle is initiated when one of the following conditions is detected:
The battery voltage falls below the V(OREG) – V(RCH) threshold.
VBUS Power-on reset (POR), if battery voltage is below the V(LOWV) threshold.
CE bit toggle or RESET bit is set (Host controlled)
9.4.4 Thermal Regulation and Protection
To prevent overheating of the chip during the charging process, the IC monitors the junction temperature, TJ, of
the die and begins to taper down the charge current once TJ reaches the thermal regulation threshold, TCF. The
charge current is reduced to zero when the junction temperature increases approximately 10°C above TCF. In
any state, if TJ exceeds TSHTDWN, the IC suspends charging. In thermal shutdown mode, PWM is turned off and
all timers are frozen. Charging resumes when TJ falls below TSHTDWN by approximately 10°C.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
23
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
Device Functional Modes (continued)
9.4.5 Charge Status Output, STAT Pin
The STAT pin is used to indicate operation conditions for bq24153A/6A/8/9. STAT is pulled low during charging
when EN_STAT bit in control register (00H) is set to “1”. Under other conditions, STAT pin behaves as a high
impedance (open-drain) output. Under fault conditions, a 128-µs pulse will be sent out to notify the host. The
status of STAT pin at different operation conditions is summarized in Table 1. The STAT pin can be used to drive
an LED or communicate to the host processor.
Table 1. STAT Pin Summary
CHARGE STATE
STAT
Charge in progress and EN_STAT=1
Low
Other normal conditions
Open-drain
Charge mode faults: Timer fault, sleep mode, VBUS or battery overvoltage, poor input source,
VBUS UVLO, no battery, thermal shutdown
128-μs pulse, then open-drain
Boost mode faults (bq24153A/8 only): Timer fault, over load, VBUS or battery overvoltage, low
battery voltage, thermal shutdown
128-μs pulse, then open-drain
9.4.6 Control Bits in Charge Mode
9.4.6.1
CE Bit (Charge Mode)
The CE bit in the control register is used to disable or enable the charge process. A low logic level (0) on this bit
enables the charge and a high logic level (1) disables the charge.
9.4.6.2 RESET Bit
The RESET bit in the control register is used to reset all the charge parameters. Writing ‘1” to the RESET bit will
reset all the charge parameters to default values except the safety limit register, and RESET bit is automatically
cleared to zero once the charge parameters get reset. It is designed for charge parameter reset before charge
starts and it is not recommended to set the RESET bit while charging or boosting are in progress.
9.4.6.3 OPA_Mode Bit
OPA_MODE is the operation mode control bit. When OPA_MODE = 0, the IC operates as a charger if
HZ_MODE is set to "0", refer to Table 2 for detail. When OPA_MODE=1 and HZ_MODE=0, the IC operates in
boost mode.
Table 2. Operation Mode Summary
OPA_MODE
HZ_MODE
OPERATION MODE
0
0
Charge (no fault)
Charge configure (fault, Vbus > UVLO)
High impedance (Vbus < UVLO)
1(bq24153A/8 only)
0
Boost (no faults)
Any fault go to charge configure mode
X
1
High impedance
9.4.7 Control Pins in Charge Mode
9.4.7.1 CD Pin (Charge Disable)
The CD pin is used to disable the charging process. When the CD pin is low, charge is enabled. When the CD
pin is high, charge is disabled and the charger enters high impedance (Hi-Z) mode.
24
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
9.4.7.2 SLRST Pin (Safety Limit Register 06H Reset, bq24156A/9 only)
The safety limit registers provide a means to limit both the maximum charge current and maximum battery
regulation voltage at POR regardless of subsequent attempts to increase them via I2C. When the SLRST pin is
low, bq24156A/9 will reset all the safety limits to default values, regardless of the write actions to safety limits
registers (06H). When the SLRST pin is high, the bq24156A/9 can program the safety limit register until any write
action to other registers locks the programmed safety limits.
9.4.8 BOOST Mode Operation (bq24153A/8 only)
In 32 second mode, when OTG pin is high (and OTG_EN bit is high thereby enabling OTG functionality) or the
operation mode bit (OPA_MODE) is set to 1, bq24153A/8 operates in boost mode and delivers the power to
VBUS from the battery. In normal boost mode, bq24153A/8 converts the battery voltage to VBUS-B (about 5.05V)
and delivers a current as much as IBO (about 200mA) to support other USB OTG devices connected to the USB
connector.
9.4.8.1 PWM Controller in Boost Mode
Similar to charge mode operation, in boost mode, the IC provides an integrated, fixed 3 MHz frequency voltagemode controller to regulate output voltage at PMID pin (VPMID). The voltage control loop is internally
compensated using a Type-III compensation scheme that provides enough phase margin for stable operation
with a wide load range and battery voltage range.
In boost mode, the input N-FET (Q1) prevents battery discharge when VBUS pin is over loaded. Cycle-by-cycle
current limit is sensed through the internal sense FET for Q3. The cycle-by-cycle current limit threshold for Q3 is
set to a nominal 1.0-A peak current. Synchronous operation is used in PWM mode to minimize power losses.
9.4.8.2 Boost Start Up
To prevent the inductor saturation and limit the inrush current, a soft-start control is applied during the boost start
up.
9.4.8.3 PFM Mode at Light Load
In boost mode, under light load conditions, the IC operates in pulse skipping mode (PFM mode) to reduce the
power loss and improve the converter efficiency. During boosting, the PWM converter is turned off once the
inductor current is less than 75mA; and the PWM is turned back on only when the voltage at PMID pin drops to
about 99.5% of the rated output voltage. A unique pre-set circuit is used to make the smooth transition between
PWM and PFM mode.
9.4.8.4 Safety Timer in Boost Mode
At the beginning of boost operation, the IC starts a 32-second timer that is reset by the host using the I2C
interface. Writing “1” to reset bit of TMR_RST in control register will reset the 32-second timer and TMR_RST is
automatically set to “0” after the 32-second timer is reset. Once the 32-second timer expires, the IC turns off the
boost converter, enunciates the fault pulse from the STAT pin and sets fault status bits in the status register. The
fault condition is cleared by POR or host control.
9.4.8.5 Protection in Boost Mode
9.4.8.5.1 Output Overvoltage Protection
The IC provides a built-in over-voltage protection to protect the device and other components against damage if
the VBUS voltage goes too high. When an over-voltage condition is detected, the IC turns off the PWM
converter, resets OPA_MODE bit to 0, sets fault status bits, and sends out a fault pulse from the STAT pin. Once
VBUS drops to the normal level, the boost starts after host sets OPA_MODE to “1” or OTG pin stays in active
status.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
25
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
9.4.8.5.2 Output Overload Protection
The IC provides a built-in over-load protection to prevent the device and battery from damage when VBUS is
over loaded. Once the over load condition is detected, Q1 operates in linear mode to limit the output current. If
the over load condition lasts for more than 30ms, the over-load fault is detected. When an over-load condition is
detected, the IC turns off the PWM converter, resets OPA_MODE bit to 0, sets fault status bits and sends out
fault pulse in STAT pin. The boost will not start until the host clears the fault register.
9.4.8.5.3 Battery Overvoltage Protection
During boosting, when the battery voltage is above the battery over voltage threshold, VBATMAX, or below the
minimum battery voltage threshold, VBATMIN, the IC turns off the PWM converter, resets OPA_MODE bit to 0, sets
fault status bits and sends out fault pulse in STAT pin. Once the battery voltage goes above VBATMIN, the boost
will start after the host sets OPA_MODE to “1” or OTG pin stays in active status.
9.4.8.6 STAT Pin in Boost Mode
During normal boosting operation, the STAT pin behaves as a high impedance (open-drain) output. Under fault
conditions, a 128-μs pulse is sent out to notify the host.
9.4.9 High Impedance (HI-Z) Mode
In Hi-Z mode, the charger stops charging and enters a low quiescent current state to conserve power. Taking the
CD pin high causes the charger to enter Hi-Z mode. When in 15-minute mode and the CD pin is low, the charger
automatically enters Hi-Z mode if
1. VBUS > UVLO and a battery with VBAT > VLOWV is inserted, or
2. VBUS falls below UVLO.
Taking the CD pin high while in 15-minute mode resets the 15 minute timer.
When in HOST mode and the CD is low, the charger can be placed into Hi-Z mode if the HZ-MODE control bit is
set to “1” and OTG pin is not in active status. Once the bq24153A/6A/8/9 enters Hi-Z mode and the CD pin is
low, a low power 32-second timer is enabled when the battery voltage is below V(LOWV) to monitor if the host
control is available or not. If the low power 32-second timer expires, the IC operates in 15-minute mode and the
low power 32 second timer is disabled.
In order to exit Hi-Z mode, the CD pin must be low, VBUS must be higher than UVLO and the HOST must write
a "0" to the HZ-MODE control bit.
9.5 Programming
9.5.1 Serial Interface Description
I2C is a 2-wire serial interface developed by Philips Semiconductor (see I2C-Bus Specification, Version 2.1,
January 2000). The bus consists of a data line (SDA) and a clock line (SCL) with pull-up structures. When the
bus is idle, both SDA and SCL lines are pulled high. All the I2C compatible devices connect to the I2C bus
through open drain I/O pins, SDA and SCL. A master device, usually a microcontroller or a digital signal
processor, controls the bus. The master is responsible for generating the SCL signal and device addresses. The
master also generates specific conditions that indicate the START and STOP of data transfer. A slave device
receives and/or transmits data on the bus under control of the master device.
The IC works as a slave and is compatible with the following data transfer modes, as defined in the I2C-Bus
Specification: standard mode (100 kbps), fast mode (400 kbps), and high-speed mode (up to 3.4 Mbps in write
mode). The interface adds flexibility to the battery charge solution, enabling most functions to be programmed to
new values depending on the instantaneous application requirements. Register contents remain intact as long as
supply voltage remains above 2.2 V (typical). I2C is asynchronous, which means that it runs off of SCL. The
device has no noise or glitch filtering on SCL, so SCL input needs to be clean. Therefore, it is recommended that
SDA changes while SCL is LOW.
The data transfer protocol for standard and fast modes is the same; therefore, they are referred to as F/S-mode
in this document. The protocol for high-speed mode is different from the F/S-mode, and it is referred to as HSmode. The bq24153A/6A/8/9 device supports 7-bit addressing only. The device 7-bit address is defined as
‘1101011’ (6BH) for bq24153A, and ‘1101010’ (6AH) for bq24156A/8/9.
26
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
Programming (continued)
9.5.1.1 F/S Mode Protocol
The master initiates data transfer by generating a start condition. The start condition is when a high-to-low
transition occurs on the SDA line while SCL is high, as shown in Figure 20. All I2C-compatible devices should
recognize a start condition.
DATA
CLK
S
P
START Condition
STOP Condition
Figure 20. START and STOP Condition
The master then generates the SCL pulses, and transmits the 8-bit address and the read/write direction bit R/W
on the SDA line. During all transmissions, the master ensures that data is valid. A valid data condition requires
the SDA line to be stable during the entire high period of the clock pulse (see Figure 21). All devices recognize
the address sent by the master and compare it to their internal fixed addresses. Only the slave device with a
matching address generates an acknowledge (see Figure 21) by pulling the SDA line low during the entire high
period of the ninth SCL cycle. Upon detecting this acknowledge, the master knows that communication link with a
slave has been established.
DATA
CLK
Data Line
Stable;
Data Valid
Change
of Data
Allowed
Figure 21. Bit Transfer on the Serial Interface
The master generates further SCL cycles to either transmit data to the slave (R/W bit 1) or receive data from the
slave (R/W bit 0). In either case, the receiver needs to acknowledge the data sent by the transmitter. So an
acknowledge signal can either be generated by the master or by the slave, depending on which one is the
receiver. The 9-bit valid data sequences consisting of 8-bit data and 1-bit acknowledge can continue as long as
necessary. To signal the end of the data transfer, the master generates a stop condition by pulling the SDA line
from low to high while the SCL line is high (see Figure 23). This releases the bus and stops the communication
link with the addressed slave. All I2C compatible devices must recognize the stop condition. Upon the receipt of a
stop condition, all devices know that the bus is released, and they wait for a start condition followed by a
matching address. If a transaction is terminated prematurely, the master needs to send a STOP condition to
prevent the slave I2C logic from getting stuck in a bad state. Attempting to read data from register addresses not
listed in this section will result in FFh being read out.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
27
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
Programming (continued)
Data Output
by Transmitter
Not Acknowledge
Data Output
by Receiver
Acknowledge
SCL From
Master
1
9
8
2
Clock Pulse for
Acknowledgement
START
Condition
Figure 22. Acknowledge on the I2C Bus™
Recognize START or
REPEATED START
Condition
Recognize STOP or
REPEATED START
Condition
Generate ACKNOWLEDGE
Signal
P
SDA
Acknowledgement
Signal From Slave
MSB
Sr
Address
R/W
SCL
S
or
Sr
ACK
ACK
Sr
or
P
Clock Line Held Low While
Interrupts are Serviced
Figure 23. Bus Protocol
9.5.1.2 H/S Mode Protocol
When the bus is idle, both SDA and SCL lines are pulled high by the pull-up devices.
The master generates a start condition followed by a valid serial byte containing HS master code 00001XXX.
This transmission is made in F/S-mode at no more than 400 Kbps. No device is allowed to acknowledge the HS
master code, but all devices must recognize it and switch their internal setting to support 3.4-Mbps operation.
The master then generates a repeated start condition (a repeated start condition has the same timing as the start
condition). After this repeated start condition, the protocol is the same as F/S-mode, except that transmission
speeds up to 3.4 Mbps are allowed. A stop condition ends the HS-mode and switches all the internal settings of
the slave devices to support the F/S-mode. Instead of using a stop condition, repeated start conditions should be
used to secure the bus in HS-mode. If a transaction is terminated prematurely, the master needs sending a
STOP condition to prevent the slave I2C logic from getting stuck in a bad state.
Attempting to read data from register addresses not listed in this section results in FFh being read out.
28
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
Programming (continued)
I2C Update Sequence
9.5.1.3
The IC requires a start condition, a valid I2C address, a register address byte, and a data byte for a single
update. After the receipt of each byte, the IC acknowledges by pulling the SDA line low during the high period of
a single clock pulse. A valid I2C address selects the IC. The IC performs an update on the falling edge of the
acknowledge signal that follows the LSB byte.
For the first update, the IC requires a start condition, a valid I2C address, a register address byte, a data byte.
For all consecutive updates, The IC needs a register address byte, and a data byte. Once a stop condition is
received, the IC releases the I2C bus, and awaits a new start conditions.
S
SLAVE ADDRESS
R/W
A
REGISTER ADDRESS
A
DATA
A/A
P
Data Transferred
(n Bytes + Acknowledge)
‘0’ (Write)
From master to IC
A
A
From IC to master
S
Sr
P
= Acknowledge (SDA LOW)
= Not acknowledge (SDA
HIGH)
= START condition
= Repeated START condition
= STOP condition
(a) F/S-Mode
F/S-Mode
S
F/S-Mode
HS-Mode
HS-MASTER CODE
A
Sr
SLAVE ADDRESS
R/W
A
REGISTER ADDRESS
A
DATA
A/A
Data Transferred
(n Bytes + Acknowledge)
‘0’ (write)
P
HS-Mode
Continues
Sr
Slave A.
(b) HS- Mode
Figure 24. Data Transfer Format in F/S Mode and H/S Mode
9.5.1.4 Slave Address Byte
MSB
X
LSB
1
1
0
1
0
1
1
The slave address byte is the first byte received following the START condition from the master device.
9.5.1.5 Register Address Byte
MSB
0
LSB
0
0
0
0
D2
D1
D0
Following the successful acknowledgment of the slave address, the bus master will send a byte to the IC, which
contains the address of the register to be accessed. The IC contains five 8-bit registers accessible via a
bidirectional I2C-bus interface. Among them, four internal registers have read and write access; and one has only
read access.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
29
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
9.6 Register Maps
9.6.1 Status/Control Register [Memory Location: 00, Reset State: x1xx 0xxx]
Table 3. Status/Control Register (Read/Write)
Memory Location: 00, Reset State: x1xx 0xxx
BIT
NAME
READ/WRITE
FUNCTION
B7 (MSB)
TMR_RST/OTG
Read/Write
Write: TMR_RST function, write "1" to reset the safety timer (auto clear)
Read: OTG pin status, (for bq24153A/8 only) 0-OTG pin at Low level, 1-OTG pin at High
level
SLRST pin status (for bq2156A/9 only), 0-SLRST pin at LOW level, 1-SLRST pin at HIGH
level.
B6
EN_STAT
Read/Write
0-Disable STAT pin function, 1-Enable STAT pin function (default 1)
B5
STAT2
Read Only
B4
STAT1
Read Only
B3
BOOST
Read Only
B2
FAULT_3
Read Only
B1
FAULT_2
Read Only
B0 (LSB)
FAULT_1
Read Only
00-Ready, 01-Charge in progress, 10-Charge done, 11-Fault
1-Boost mode, 0-Not in boost mode, for bq24153A/8 only;
NA–for bq24156A/9.
Charge mode: 000-Normal, 001-VBUS OVP, 010-Sleep mode, 011-Bad Adaptor or
VBUS<VUVLO,
100-Output OVP, 101-Thermal shutdown, 110-Timer fault, 111-No battery
Boost mode (for bq24153A/8 only): 000-Normal, 001-VBUS OVP, 010-Over load, 011Battery voltage is too low, 100-Battery OVP, 101-Thermal shutdown, 110-Timer fault, 111NA
9.6.2 Control Register [Memory Location: 01, Reset State: 0011 0000]
Table 4. Control Register (Read/Write)
Memory Location: 01, Reset State: 0011 0000
BIT
NAME
READ/WRITE
B7 (MSB)
Iin_Limit_2
Read/Write
B6
Iin_Limit_1
B5
B4
FUNCTION
Read/Write
00-USB host with 100-mA current limit, 01-USB host with 500-mA current limit, 10USB host/charger with 800-mA current limit, 11-No input current limit (default 00 for
bq24153A/8, default 01 for bq24156A/9)
V(LOWV_2)
(1)
Read/Write
Weak battery voltage threshold: 200mV step (default 1)
V(LOWV_1)
(1)
Read/Write
Weak battery voltage threshold: 100mV step (default 1)
B3
TE
Read/Write
1-Enable charge current termination, 0-Disable charge current termination (default 0)
B2
CE
Read/Write
1-Charger is disabled, 0-Charger enabled (default 0)
B1
HZ_MODE
Read/Write
1-High impedance mode, 0-Not high impedance mode (default 0)
B0 (LSB)
OPA_MODE
Read/Write
1-Boost mode, 0-Charger mode (default 0), for bq24153A/8 only; NA–for bq24156A/9.
(1)
30
The range of the weak battery voltage threshold (V(LOWV)) is 3.4 V to 3.7 V with an offset of 3.4 V and steps of 100 mV (default 3.7 V,
using bits B4-B5).
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
9.6.3 Control/Battery Voltage Register [Memory Location: 02, Reset State: 0000 1010]
Table 5. Control/Battery Voltage Register (Read/Write)
Memory Location: 02, Reset State: 0000 1010
BIT
NAME
READ/WRITE
B7 (MSB)
VO(REG5)
Read/Write
Battery Regulation Voltage: 640 mV step (default 0)
FUNCTION
B6
VO(REG4)
Read/Write
Battery Regulation Voltage: 320 mV step (default 0)
B5
VO(REG3)
Read/Write
Battery Regulation Voltage: 160 mV step (default 0)
B4
VO(REG2)
Read/Write
Battery Regulation Voltage: 80 mV step (default 0)
B3
VO(REG1)
Read/Write
Battery Regulation Voltage: 40 mV step (default 1)
B2
VO(REG0)
Read/Write
Battery Regulation Voltage: 20 mV step (default 0)
B1
OTG_PL
Read/Write
1-OTG Boost Enable with High level, 0-OTG Boost Enable with Low level (default 1),
for bq24153A/8 only; NA–for bq24156A/9; not applicable to OTG pin control of
current limit at POR in 15-minute mode
B0 (LSB)
OTG_EN
Read/Write
1-Enable OTG Pin in HOST mode, 0-Disable OTG pin in HOST mode (default 0), for
bq24153A/8 only; NA–for bq24156A/9; not applicable to OTG pin control of current
limit at POR in 15-minute mode
9.6.4 Vender/Part/Revision Register [Memory Location: 03, Reset State: 0101 000x]
• Charge voltage range is 3.5 V to 4.44 V with the offset of 3.5 V and steps of 20 mV (default 3.54 V), using
bits B2-B7.
Table 6. Vender/Part/Revision Register (Read only)
Memory Location: 03, Reset State: 0101 000x
BIT
NAME
READ/WRITE
B7 (MSB)
Vender2
Read Only
Vender Code: bit 2 (default 0)
B6
Vender1
Read Only
Vender Code: bit 1 (default 1)
B5
Vender0
Read Only
Vender Code: bit 0 (default 0)
B4
PN1
Read Only
B3
PN0
Read Only
For I2C Address 6BH: 10–bq24153A; 11–NA.
For I2C Address 6AH: 00--bq24156A/9, 01–NA, 10–bq24158, 11–NA.
B2
Revision2
Read Only
B1
Revision1
Read Only
B0 (LSB)
Revision0
Read Only
Copyright © 2010–2016, Texas Instruments Incorporated
FUNCTION
011: Revision 1.0;
001: Revision 1.1;
100-111: Future Revisions
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
31
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
9.6.5 Battery Termination/Fast Charge Current Register [Memory Location: 04, Reset State: 0000 000]
Table 7. Battery Termination/Fast Charge Current Register (Read/Write)
Memory Location: 04, Reset State: 0000 0001
(1)
(2)
•
•
BIT
NAME
READ/WRITE
B7 (MSB)
Reset
Read/Write
Write: 1-Charger in reset mode, 0-No effect, Read: always get "0"
FUNCTION
B6
VI(CHRG3)
(1)
Read/Write
Charge current sense voltage: 27.2 mV step – for bq24153A/8; 54.4mV step – for
bq24156A/9 (default 0)
B5
VI(CHRG2)
(1)
Read/Write
Charge current sense voltage: 13.6 mV step – for bq24153A/8; 27.2mV step – for
bq24156A/9 (default 0)
B4
VI(CHRG1)
(1)
Read/Write
Charge current sense voltage: 6.8 mV step – for bq24153A/8; 13.6mV step – for
bq24156A/9 (default 0)
B3
VI(CHRG0)
(1)
Read/Write
NA – for bq24153A/8; 6.8mV step – for bq24156A/9 (default 0)
B2
VI(TERM2)
(2)
Read/Write
Termination current sense voltage: 13.6 mV step (default 0)
B1
VI(TERM1)
(2)
Read/Write
Termination current sense voltage: 6.8 mV step (default 0)
B0 (LSB)
VI(TERM0)
(2)
Read/Write
Termination current sense voltage: 3.4 mV step (default 1)
See Table 13
See Table 12
For bq24153A/8, charge current sense voltage offset is 37.4mV and default charge current is 550mA, if 68mΩ sensing resistor is used and LOW_CHG=0.
For bq24156A/9, the maximum charge current is 1.55A. If a higher value is programmed, the 1.55A or
maximum safety limit charge current is selected.
9.6.6 Special Charger Voltage/Enable Pin Status Register [Memory location: 05, Reset state: 001X X100]
Table 8. Special Charger Voltage/Enable Pin Status Register
Memory location: 05, Reset state: 001X X100
•
•
32
BIT
NAME
READ/WRITE
FUNCTION
B7 (MSB)
NA
Read/Write
NA
B6
NA
Read/Write
NA
B5
LOW_CHG
Read/Write
0 – Normal charge current sense voltage at 04H,
1 – Low charge current sense voltage of 22.1mV (default 1)
B4
DPM_STATUS
Read Only
0 – DPM mode is not active,
1 – DPM mode is active
B3
CD_STATUS
Read Only
0 – CD pin at LOW level,
1 – CD pin at HIGH level
B2
VSREG2
Read/Write
Special charger voltage: 320mV step (default 1)
B1
VSREG1
Read/Write
Special charger voltage: 160mV step (default 0)
B0 (LSB)
VSREG0
Read/Write
Special charger voltage: 80mV step (default 0)
Special charger voltage offset is 4.2V and default special charger voltage is 4.52V.
Default charge current will be 325mA, if 68-mΩ sensing resistor is used, since default LOW_CHG=1.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
9.6.7 Safety Limit Register [Memory location: 06, Reset state: 01000000]
Table 9. Safety Limit Register (READ/WRITE, Write only once after reset!)
Memory location: 06, Reset state: 01000000
BIT
(1)
•
•
•
•
NAME
READ/WRITE
FUNCTION
B7 (MSB)
VMCHRG3
(1)
Read/Write
Maximum charge current sense voltage: 54.4 mV step (default 0)
B6
VMCHRG2
(1)
Read/Write
Maximum charge current sense voltage: 27.2 mV step (default 1)
B5
VMCHRG1
(1)
Read/Write
Maximum charge current sense voltage: 13.6 mV step (default 0)
B4
VMCHRG0
(1)
Read/Write
Maximum charge current sense voltage: 6.8 mV step (default 0)
B3
VMREG3
Read/Write
Maximum battery regulation voltage: 160 mV step (default 0)
B2
VMREG2
Read/Write
Maximum battery regulation voltage: 80 mV step (default 0)
B1
VMREG1
Read/Write
Maximum battery regulation voltage: 40 mV step (default 0)
B0 (LSB)
VMREG0
Read/Write
Maximum battery regulation voltage: 20 mV step (default 0)
Refer to Table 13
Maximum charge current sense voltage offset is 37.4 mV (550mA), default at 64.6mV (950mA) and the
maximum charge current option is 1.55A (105.4mV), if 55-mΩ sensing resistor is used.
Maximum battery regulation voltage offset is 4.2V (default at 4.2V) and maximum battery regulation voltage
option is 4.44V.
Memory location 06H resets only when V(CSOUT) drops below either 1) V(SHORT) threshold (typ. 2.05V) if VBUS
> V(UVLO), 2) the digital reset threshold (typ. 2.4V) if VBUS < V(UVLO) or 3) SLRST (pin D4, for bq24156A/9
only) goes to logic ‘0’. After reset, the maximum values for battery regulation voltage and charge current can
be programmed until any writing to other register locks the safety limits. Programmed values exclude higher
values from memory locations 02 (battery regulation voltage), and from memory location 04 (Fast charge
current).
If host accesses (write command) to some other register before Safety limit register, the safety default values
are used.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
33
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
10 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
The bq24153A/6A/8/9 is a compact, flexible, high-efficiency, USB-friendly, switch-mode charge management
solution for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The devices
integrate a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and
voltage regulation, and charge termination, into a small DSBGA package. The charge parameters can be
programmed through an I2C interface.
10.2 Typical Application
VBUS = 5 V, ICHARGE = 1250 mA, VBAT = 3.5 V to 4.44 V (Adjustable).
LO 1.0 mH
VBUS
VBUS
CIN
VBAT
SW
CO1
CBOOT
U1
bq24153A/8
1 mF
RSNS
CO2
22 mF
33 mF
33 nF
C IN 4.7 mF
BOOT
PMID
VAUX
PACK+
CCSIN
PGND
+
0.1 mF
CSIN
10 kW
10 kW 10 kW 10 kW
I
2C BUS
PACK–
CSOUT
SCL
SCL
SDA
STAT
SDA
STAT
OTG
10 kW
CCSOUT
VREF
OTG
CD
CD
0.1 mF
CVREF
1 mF
10 kW
HOST
Copyright © 2016, Texas Intruments Incorporated
2
Figure 25. I C Controlled 1-Cell USB Charger Application Circuit with USB OTG Support.
10.2.1 Design Requirements
Use the following typical application design procedure to select external components values for the
bq24153A/6A/8/9 device.
Table 10. Design Parameters
SPECIFICATIONS
TEST CONDITIONS
Input DC voltage, VIN
Input voltage from AC adapter input
Input current
Maximum input current from AC adapter input
Charge current
Battery charge current
Output regulation voltage
Voltage applied to VBAT
Operating junction temperature range, TJ
34
MIN
TYP
UNIT
5
6
V
0.1
0.1 to 0.5
1.5
A
0.325
0.7
1.55
A
0
0.3 to 4.2
4.44
V
125
°C
0
Submit Documentation Feedback
MAX
4
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
10.2.2 Detailed Design Procedure
10.2.2.1 Systems Design Specifications
• VBUS = 5 V
• VBAT = 4.2 V (1-Cell)
• I(charge) = 1.25 A
• Inductor ripple current = 30% of fast charge current
1. Determine the inductor value (LOUT) for the specified charge current ripple:
VBAT ´ (VBUS - VBAT)
VBUS ´ f ´ D IL
L OUT =
, the worst case is when battery voltage is as close as to half of the input
voltage.
LOUT =
2.5 ´ (5 - 2.5)
5 ´ (3 ´ 106 ) ´ 1.25 ´ 0.3
(1)
LOUT = 1.11 μH
Select the output inductor to standard 1 μH. Calculate the total ripple current with using the 1-μH inductor:
DIL =
VBAT ´ (VBUS - VBAT)
VBUS ´ f ´ LOUT
(2)
2.5 ´ (5 - 2.5)
DIL =
5 ´ (3 ´ 106 ) ´ (1 ´ 10-6 )
(3)
ΔIL = 0.42 A
Calculate the maximum output current:
DIL
ILPK = IOUT +
2
(4)
0.42
ILPK = 1.25 +
2
(5)
ILPK = 1.46 A
Select 2.5mm by 2mm 1-μH 1.5-A surface mount multi-layer inductor. The suggested inductor part numbers
are shown as following.
Table 11. Inductor Part Numbers (1)
PART NUMBER
INDUCTANCE
SIZE
MANUFACTURER
LQM2HPN1R0MJ0
1 μH
2.5 x 2.0 mm
Murata
MIPS2520D1R0
1 μH
2.5 x 2.0 mm
FDK
MDT2520-CN1R0M
1 μH
2.5 x 2.0 mm
TOKO
CP1008
1 μH
2.5 x 2.0 mm
Inter-Technical
(1)
See Third-Party Products discalimer
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
35
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
2. Determine the output capacitor value (COUT) using 40 kHz as the resonant frequency:
1
fo =
2p ´
LOUT ´ COUT
(6)
1
COUT =
4p2 ´ f02 ´ LOUT
1
COUT =
(7)
4p2 ´ (40 ´ 103 )2 ´ (1 ´ 10-6 )
(8)
COUT = 15.8 μF
Select two 0603 X5R 6.3V 10-μF ceramic capacitors in parallel i.e., Murata GRM188R60J106M.
3. Determine the sense resistor using the following equation:
V(RSNS)
R(SNS) =
I(CHARGE)
(9)
The maximum sense voltage across the sense resistor is 85 mV. In order to get a better current regulation
accuracy, V(RSNS) should equal 85mV, and calculate the value for the sense resistor.
85mV
R(SNS) =
1.25A
(10)
R(SNS) = 68 mΩ
This is a standard value. If it is not a standard value, then choose the next close value and calculate the real
charge current. Calculate the power dissipation on the sense resistor:
P(RSNS) = I(CHARGE) 2 × R(SNS)
P(RSNS) = 1.252 × 0.068
P(RSNS) = 0.106 W
Select 0402 0.125-W 68-mΩ 2% sense resistor, i.e. Panasonic ERJ2BWGR068.
4. Measured efficiency and total power loss with different inductors are shown in Figure 26 and Figure 27. SW
node and inductor current waveform are shown in Figure 2.
90
800
89
700
600
87
Loss (mW)
Efficiency (%)
88
86
85
84
82
500
600
700
800
400
300
FDK
TOKO
Inter-Technical
muRata
83
500
FDK
TOKO
Inter-Technical
muRata
200
100
900
1000
1100
1200
1300
500
600
700
Charge Current (mA)
TA = 25°C
VBUS = 5 V
VBAT = 3 V
Figure 26. Measured Battery Charge Efficiency
36
Submit Documentation Feedback
800
900
1000
1100
1200
1300
Charge Current (mA)
TA = 25°C
VBUS = 5 V
VBAT = 3 V
Figure 27. Measured Battery Charge Loss
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
10.2.2.2 Charge Current Sensing Resistor Selection Guidelines
Both the termination current range and charge current range depend on the sensing resistor (RSNS). The
termination current step (IOTERM_STEP) can be calculated using Equation 11:
IO(TERM_STEP) =
VI(TERM0)
R(SNS)
(11)
Table 12 shows the termination current settings for three sensing resistors.
Table 12. Termination Current Settings for 55-mΩ, 68-mΩ, 100-mΩ Sense Resistors
BIT
VI(TERM) (mV)
I(TERM) (mA)
R(SNS) = 55mΩ
I(TERM) (mA)
R(SNS) = 68mΩ
I(TERM) (mA)
R(SNS) = 100mΩ
VI(TERM2)
13.6
247
200
136
VI(TERM1)
6.8
124
100
68
VI(TERM0)
3.4
62
50
34
Offset
3.4
62
50
34
For example, with a 68-mΩ sense resistor, V(ITERM2)=1, V(ITERM1)=0, and V(ITERM0)=1, ITERM = [ (13.6mV x 1) +
(6.8mV x 0) + (3.4mV x 1) + 3.4mV ] / 68mΩ = 200mA + 0 + 50mA + 50mA = 300mA.
The charge current step (IO(CHARGE_STEP)) is calculated using Equation 12:
VI(CHRG0)
IO(CHARGE_STEP) =
R(SNS)
(12)
Table 13 shows the charge current settings for three sensing resistors.
Table 13. Charge Current Settings for 55-mΩ, 68-mΩ and 100-mΩ Sense Resistors
BIT
IO(CHARGE) (mA)
R(SNS) = 55mΩ
VI(REG) (mV)
IO(CHARGE) (mA)
R(SNS) = 68mΩ
IO(CHARGE) (mA)
R(SNS) = 100mΩ
bq24156A
bq24159
bq24153A
bq24158
bq24156A
bq24159
bq24153A
bq24158
bq24156A
bq24159
bq24153A
bq24158
bq24156A
bq24159
bq24153A
bq24158
VI(CHRG3)
54.4
27.2
989
495
800
400
544
272
VI(CHRG2)
27.2
13.6
495
247
400
200
272
136
VI(CHRG1)
13.6
6.8
247
124
200
100
136
68
VI(CHRG0)
6.8
n/a
124
n/a
100
n/a
68
n/a
Offset
37.4
37.4
680
680
550
550
374
374
Using bq24156A as an example, with a 68-mΩ sense resistor, V(CHRG3)=1, V(CHRG2)=0, V(ICHRG1)=0, and
V(ICHRG0)=1, ITERM = [ (54.4mV x 1) + (27.2mV x 0) + (13.6mV x 0) + (6.8mV x 1) + 37.4mV ] / 68mΩ = 800mA +
0 + 0 + 100mA = 900mA.
10.2.2.3 Output Inductor and Capacitance Selection Guidelines
The IC provides internal loop compensation. With the internal loop compensation, the highest stability occurs
when the LC resonant frequency, fo, is approximately 40 kHz (20 kHz to 80 kHz). Equation 13 can be used to
calculate the value of the output inductor, LOUT, and output capacitor, COUT.
fo =
1
2p ´
LOUT ´ COUT
(13)
To reduce the output voltage ripple, a ceramic capacitor with the capacitance between 4.7 μF and 47 μF is
recommended for COUT, see the application section for components selection.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
37
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
10.2.3 Application Curves
Using circuit shown in Figure 25, TA = 25°C, unless otherwise specified.
VBUS
2 V/div
VBAT
2 V/div
VSW
5 V/div
VSW
5 V/div
IBAT
0.5 A/div
IBAT
0.5 A/div
Battery Inserted
Battery Removed
1 S/div
10 ms/div
VBUS = 0-5V,
VBAT = 3.5V,
Iin_limit = 500mA,
ICHG = 550mA,
Voreg = 4.2V
32S mode
VBUS = 5 V,
VBAT = 3.4V,
Iin_limit = 500 mA
(32s Mode)
Figure 29. Battery Insertion/Removal
Figure 28. Adapter Insertion
VBUS
5 V/div
VBUS
4 V/div
VBAT
2 V/div
VBAT
2 V/div
VSW
5 V/div
IBUS
50 mA/div
IBUS
100 mA/div
100 mS/div
VBUS = 5V,
100 ms/div
VBUS = 5V,
No Battery Connected
Figure 30. Battery Detection at Power Up (bq24153A/6A)
VBUS
10 mV/div,
5.05 V Offset
No Battery Connected
Figure 31. Battery Detection at Power Up (bq24158/9)
VBUS
100 mV/div,
5.05 V Offset
VBAT
10 mV/div,
3.5 V Offset
VBAT
100 mV/div,
3.5 V Offset
VSW
2V/div
VSW
2 V/div
IL
100 mA/div
IL
0.2 A/div
5 mS/div
100 nS/div
VBUS = 5.05 V,
VBAT = 3.5V,
IBUS = 217 mA
Figure 32. BOOST Waveform (PWM Mode)
38
Submit Documentation Feedback
VBUS = 5.05 V,
VBAT = 3.5V,
IBUS = 42 mA
Figure 33. BOOST Waveform (PFM Mode)
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
VBUS
100 mV/div
5.05 V Offset
VBUS
100 mV/div,
5.05 V Offset
VBAT
0.2 V/div
3.5 V Offset
VBAT
0.2 V/div,
3.5 V Offset
VSW
5 V/div
VSW
5 V/div
IBAT
0.1 A/div
IBAT
0.1 A/div
100 mS/div
100 μs/div
VBUS = 5.05 V,
VBAT = 3.5V,
VBUS = 5.05 V,
IBUS = 0-217 mA
VBAT = 3.5V,
IBUS = 217 mA
Figure 35. Load Step Down Response (BOOST Mode)
Figure 34. Load Step Up Response (BOOST Mode)
10.3 System Example
VBUS = 5 V, ICHARGE = 1550 mA, Vbat = 3.5 V to 4.44 V (adjustable).
LO 1.0 mH
VBUS
VBUS
CIN
SW
C IN 4.7 mF
33 mF
BOOT
PACK+
+
CCSIN
PGND
VAUX
CO2
22 mF
33 nF
PMID
VBAT
CO1
CBOOT
U1
bq24156A/9
1 mF
RSNS
0.1 mF
CSIN
10 kW
10 kW 10 kW 10 kW
SLRST
10 kW
2
I C BUS
SCL
SCL
SDA
STAT
SDA
STAT
SLRST
CD
CD
10 kW
PACK–
CSOUT
CCSOUT
VREF
CVREF
0.1 mF
1 mF
HOST
Copyright © 2016, Texas Intruments Incorporated
Figure 36. I2C Controlled 1-Cell Charger Application Circuit with External Safety Limit Register Control
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
39
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
11 Power Supply Recommendations
11.1 System Load After Sensing Resistor
One of the simpler high-efficiency topologies connects the system load directly across the battery pack, as
shown in Figure 37. The input voltage has been converted to a usable system voltage with good efficiency from
the input. When the input power is on, it supplies the system load and charges the battery pack at the same time.
When the input power is off, the battery pack powers the system directly.
SW
VBUS
L1
VIN
+
-
Isys
Isns
Rsns
bq2415x
C1
PMID
Ichg
+
PGND
C4
C3
System
Load
BAT
C2
Figure 37. System Load After Sensing Resistor
The advantages of system load after sensing resistor:
1. When the AC adapter is disconnected, the battery pack powers the system load with minimum power
dissipation. Consequently, the time that the system runs on the battery pack can be maximized.
2. It reduces the number of external path selection components and offers a low-cost solution.
3. Dynamic power management (DPM) can be achieved. The total of the charge current and the system current
can be limited to a desired value by setting the charge current value. When the system current increases, the
charge current drops by the same amount. As a result, no potential over-current or over-heating issues are
caused by excessive system load demand.
4. The total input current can be limited to a desired value by setting the input current limit value. USB
specifications can be met easily.
5. The supply voltage variation range for the system can be minimized.
6. The input current soft-start can be achieved by the generic soft-start feature of the IC.
Design considerations and potential issues:
1. If the system always demands a high current (but lower than the regulation current), the battery charging
never terminates. Thus, the battery is always charged, and its lifetime may be reduced.
2. Because the total current regulation threshold is fixed and the system always demands some current, the
battery may not be charged with a full-charge rate and thus may lead to a longer charge time.
3. If the system load current is large after the charger has been terminated, the IR drop across the battery
impedance may cause the battery voltage to drop below the refresh threshold and start a new charge cycle.
The charger would then terminate due to low charge current. Therefore, the charger would cycle between
charging and terminating. If the load is smaller, the battery has to discharge down to the refresh threshold,
resulting in a much slower cycling.
4. In a charger system, the charge current is typically limited to about 30mA, if the sensed battery voltage is
below 2V short circuit protection threshold. This results in low power availability at the system bus. If an
external supply is connected and the battery is deeply discharged, below the short circuit protection
threshold, the charge current is clamped to the short circuit current limit. This then is the current available to
the system during the power-up phase. Most systems cannot function with such limited supply current, and
the battery supplements the additional power required by the system. Note that the battery pack is already at
the depleted condition, and it discharges further until the battery protector opens, resulting in a system
shutdown.
5. If the battery is below the short circuit threshold and the system requires a bias current budget lower than the
40
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
System Load After Sensing Resistor (continued)
short circuit current limit, the end-equipment will be operational, but the charging process can be affected
depending on the current left to charge the battery pack. Under extreme conditions, the system current is
close to the short circuit current levels and the battery may not reach the fast-charge region in a timely
manner. As a result, the safety timers flag the battery pack as defective, terminating the charging process.
Because the safety timer cannot be disabled, the inserted battery pack must not be depleted to make the
application possible.
6. If the battery pack voltage is too low, highly depleted, totally dead or even shorted, the system voltage is
clamped by the battery and it cannot operate even if the input power is on.
11.2 System Load Before Sensing Resistor
The second circuit is similar to first one; the difference is that the system load is connected before the sense
resistor, as shown in Figure 38.
Isys
SW
VBUS
Isns
L1
VIN
+
-
Rsns
Ichg
bq2415x
C1
PMID
+
PGND
C4
C3
System
Load
BAT
C2
Figure 38. System Load Before Sensing Resistor
The advantages of system load before sensing resistor to system load after sensing resistor:
1. The charger controller is based only on the current going through the current-sense resistor. So, the constant
current fast charge and termination functions operate without being affected by the system load. This is the
major advantage of having the system load connected before the sense resistor.
2. A depleted battery pack can be connected to the charger without the risk of the safety timer expiration
caused by high system load.
3. The charger can disable termination and keep the converter running to keep battery fully charged; or let the
switcher terminate when the battery is full and then allow the system to run off of the battery through the
sense resistor.
Design considerations and potential issues:
1. The total current is limited by the IC input current limit, or peak current protection, but not the charge current
setting. The charge current does not drop when the system current load increases until the input current limit
is reached. This solution is not recommended if the system requires a high current.
2. Efficiency declines when discharging through the sense resistor to the system.
3. No thermal regulation. Therefore, the system design should ensure the maximum junction temperature of the
IC is below 125°C during normal operation.
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
41
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
12 Layout
12.1 Layout Guidelines
It is important to pay special attention to the PCB layout. The following provides some guidelines:
• To obtain optimal performance, the power input capacitors, connected from input to PGND, should be placed
as close as possible to the pin. The output inductor should be placed close to the IC and the output capacitor
connected between the inductor and PGND of the IC. The intent is to minimize the current path loop area
from the SW pin through the LC filter and back to the PGND pin. To prevent high frequency oscillation
problems, proper layout to minimize high frequency current path loop is critical. (See Figure 39.) The sense
resistor should be adjacent to the junction of the inductor and output capacitor. Route the sense leads
connected across the RSNS back to the IC, close to each other (minimize loop area) or on top of each other
on adjacent layers (do not route the sense leads through a high-current path). (See Figure 40.)
• Place all decoupling capacitors close to their respective IC pins and close to PGND (do not place components
such that routing interrupts power stage currents). All small control signals should be routed away from the
high current paths.
• The PCB should have a ground plane (return) connected directly to the return of all components through vias
(two vias per capacitor for power-stage capacitors, two vias for the IC PGND, one via per capacitor for smallsignal components). A star ground design approach is typically used to keep circuit block currents isolated
(high-power/low-power small-signal) which reduces noise-coupling and ground-bounce issues. A single
ground plane for this design gives good results. With this small layout and a single ground plane, there is no
ground-bounce issue, and having the components segregated minimizes coupling between signals.
• The high-current charge paths into VBUS, PMID and from the SW pins must be sized appropriately for the
maximum charge current in order to avoid voltage drops in these traces. The PGND pins should be
connected to the ground plane to return current through the internal low-side FET.
• Place 4.7μF input capacitor as close to PMID pin and PGND pin as possible to make high frequency current
loop area as small as possible. Place 1μF input capacitor as close to VBUS pin and PGND pin as possible to
make high frequency current loop area as small as possible (see Figure 41).
12.1.1 Current Path
L1
VBUS
SW
R1
V BAT
High
Frequency
BAT
V IN
PMID
Current
Path
PGND
C3
C2
C1
Figure 39. High Frequency Current Path
42
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
12.2 Layout Example
Charge Current Direction
R SNS
To Inductor
To Capacitor and battery
Current Sensing Direction
To CSIN and CSOUT pin
Figure 40. Sensing Resistor PCB Layout
VBUS
PMID
SW
Vin+
1µF
Vin–
4.7µF
PGND
Figure 41. Input Capacitor Position and PCB Layout Example
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
43
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
13 Device and Documentation Support
13.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
13.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 14. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
bq24153A
Click here
Click here
Click here
Click here
Click here
bq24156A
Click here
Click here
Click here
Click here
Click here
bq24158
Click here
Click here
Click here
Click here
Click here
bq24159
Click here
Click here
Click here
Click here
Click here
13.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
13.4 Trademarks
E2E, NanoFree are trademarks of Texas Instruments.
I2C is a trademark of NXP B.V. Corporation.
13.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
13.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
44
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
14.1 Package Summary
CHIP SCALE PACKAGE
(Top Side Symbol For bq24153A)
CHIP SCALE PACKAGE
(Top Side Symbol For bq24156A)
TIYMLLLLS
bq24153A
TIYMLLLLS
bq24156A
0-Pin A1 Marker, TI-TI Letters, YM- Year Month Date Code, LLLL-Lot Trace Code, S-Assembly Site Code
CHIP SCALE PACKAGE
(Top Side Symbol For bq24158)
CHIP SCALE PACKAGE
(Top Side Symbol For bq24159)
TIYMLLLLS
bq24158
TIYMLLLLS
bq24159
Copyright © 2010–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: bq24153A bq24156A bq24158 bq24159
45
Not Recommended for New Designs bq24153A, bq24156A, bq24159
bq24153A, bq24156A
bq24158, bq24159
SLUSAB0D – OCTOBER 2010 – REVISED APRIL 2016
www.ti.com
Package Summary (continued)
WCSP PACKAGE
(Top View)
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
D1
D2
D3
D4
E1
E2
E3
E4
D
E
14.1.1 Chip Scale Packaging Dimensions
The bq24153A/6A/8/9 devices are available in a 20-bump chip scale package (YFF, NanoFree™).
The package dimensions are:
46
D
E
Max = 2.17mm
Max = 2.03 mm
Min = 2.11 mm
Min = 1.97 mm
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: bq24153A bq24156A bq24158 bq24159
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
BQ24153AYFFR
NRND
DSBGA
YFF
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ24153A
BQ24153AYFFT
NRND
DSBGA
YFF
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ24153A
BQ24156AYFFR
NRND
DSBGA
YFF
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ24156A
BQ24156AYFFT
NRND
DSBGA
YFF
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ24156A
BQ24157YFFR
ACTIVE
DSBGA
YFF
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
BQ24157A
BQ24157YFFT
ACTIVE
DSBGA
YFF
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
BQ24157A
BQ24158YFFR
ACTIVE
DSBGA
YFF
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ24158
BQ24158YFFT
ACTIVE
DSBGA
YFF
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ24158
BQ24159YFFR
NRND
DSBGA
YFF
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ24159
BQ24159YFFT
NRND
DSBGA
YFF
20
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ24159
HPA01077AYFFR
NRND
DSBGA
YFF
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ24156A
HPA01171YFFR
ACTIVE
DSBGA
YFF
20
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 85
BQ24158
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2017
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Jun-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
BQ24153AYFFR
DSBGA
YFF
20
3000
180.0
8.4
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
2.2
2.35
0.8
4.0
8.0
Q1
BQ24153AYFFT
DSBGA
YFF
20
250
180.0
8.4
2.2
2.35
0.8
4.0
8.0
Q1
BQ24156AYFFR
DSBGA
YFF
20
3000
180.0
8.4
2.2
2.35
0.8
4.0
8.0
Q1
BQ24156AYFFT
DSBGA
YFF
20
250
180.0
8.4
2.2
2.35
0.8
4.0
8.0
Q1
BQ24157YFFR
DSBGA
YFF
20
3000
180.0
8.4
2.2
2.35
0.8
4.0
8.0
Q1
BQ24157YFFT
DSBGA
YFF
20
250
180.0
8.4
2.2
2.35
0.8
4.0
8.0
Q1
BQ24158YFFR
DSBGA
YFF
20
3000
180.0
8.4
2.2
2.35
0.8
4.0
8.0
Q1
BQ24158YFFT
DSBGA
YFF
20
250
180.0
8.4
2.2
2.35
0.8
4.0
8.0
Q1
BQ24159YFFR
DSBGA
YFF
20
3000
180.0
8.4
2.2
2.35
0.8
4.0
8.0
Q1
BQ24159YFFT
DSBGA
YFF
20
250
180.0
8.4
2.2
2.35
0.8
4.0
8.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Jun-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
BQ24153AYFFR
DSBGA
YFF
20
3000
182.0
182.0
20.0
BQ24153AYFFT
DSBGA
YFF
20
250
182.0
182.0
20.0
BQ24156AYFFR
DSBGA
YFF
20
3000
182.0
182.0
20.0
BQ24156AYFFT
DSBGA
YFF
20
250
182.0
182.0
20.0
BQ24157YFFR
DSBGA
YFF
20
3000
182.0
182.0
20.0
BQ24157YFFT
DSBGA
YFF
20
250
182.0
182.0
20.0
BQ24158YFFR
DSBGA
YFF
20
3000
182.0
182.0
20.0
BQ24158YFFT
DSBGA
YFF
20
250
182.0
182.0
20.0
BQ24159YFFR
DSBGA
YFF
20
3000
182.0
182.0
20.0
BQ24159YFFT
DSBGA
YFF
20
250
182.0
182.0
20.0
Pack Materials-Page 2
D: Max = 2.172 mm, Min =2.112 mm
E: Max = 2.03 mm, Min = 1.97 mm
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated