128K x 36, 256K x 18 3.3V Synchronous ZBT™ SRAMs 2.5V I/O, Burst Counter Pipelined Outputs Features ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ IDT71V2556S IDT71V2558S IDT71V2556SA IDT71V2558SA cycle, and two cycles later the associated data cycle occurs, be it read or write. The IDT71V2556/58 contain data I/O, address and control signal registers. Output enable is the only asynchronous signal and can be used to disable the outputs at any given time. A Clock Enable (CEN) pin allows operation of the IDT71V2556/58 to be suspended as long as necessary. All synchronous inputs are ignored when (CEN) is high and the internal device registers will hold their previous values. There are three chip enable pins (CE1, CE2, CE2) that allow the user to deselect the device when desired. If any one of these three are not asserted when ADV/LD is low, no new memory operation can be initiated. However, any pending data transfers (reads or writes) will be completed. The data bus will tri-state two cycles after chip is deselected or a write is initiated. The IDT71V2556/58 has an on-chip burst counter. In the burst mode, the IDT71V2556/58 can provide four cycles of data for a single address presented to the SRAM. The order of the burst sequence is defined by the LBO input pin. The LBO pin selects between linear and interleaved burst sequence. The ADV/LD signal is used to load a new external address (ADV/LD = LOW) or increment the internal burst counter (ADV/LD = HIGH). The IDT71V2556/58 SRAMs utilize IDT's latest high-performance CMOS process and are packaged in a JEDEC standard 14mm x 20mm 100-pin thin plastic quad flatpack (TQFP) as well as a 119 ball grid array (BGA) and a 165 fine pitch ball grid array (fBGA). 128K x 36, 256K x 18 memory configurations Supports high performance system speed - 200 MHz (3.2 ns Clock-to-Data Access) ZBTTM Feature - No dead cycles between write and read cycles Internally synchronized output buffer enable eliminates the need to control OE W (READ/WRITE) control pin Single R/W Positive clock-edge triggered address, data, and control signal registers for fully pipelined applications 4-word burst capability (interleaved or linear) BW1 - BW4) control (May tie active) Individual byte write (BW Three chip enables for simple depth expansion 3.3V power supply (±5%), 2.5V I/O Supply (VDDQ) Optional - Boundary Scan JTAG Interface (IEEE 1149.1 complaint) Packaged in a JEDEC standard 100-pin plastic thin quad flatpack (TQFP), 119 ball grid array (BGA) and 165 fine pitch ball grid array (fBGA) Description The IDT71V2556/58 are 3.3V high-speed 4,718,592-bit (4.5 Megabit) synchronous SRAMS. They are designed to eliminate dead bus cycles when turning the bus around between reads and writes, or writes and reads. Thus, they have been given the name ZBTTM, or Zero Bus Turnaround. Address and control signals are applied to the SRAM during one clock Pin Description Summary A0-A17 Address Inputs Input Synchronous CE1, CE2, CE2 Chip Enables Input Synchronous OE Output Enable Input Asynchronous R/ W Read/Write Signal Input Synchronous CEN Clock Enable Input Synchronous BW1, BW2, BW3, BW4 Individual Byte Write Selects Input Synchronous CLK Clock Input N/A ADV/ LD Advance burst address / Load new address Input Synchronous LBO Linear / Interleaved Burst Order Input Static TMS Test Mode Select Input Synchronous TDI Test Data Input Input Synchronous TCK Test Clock Input N/A TDO Test Data Output Output Synchronous TRST JTAG Reset (Optional) Input Asynchronous ZZ Sleep Mode Input Synchronous I/O0-I/O31, I/OP1-I/OP4 Data Input / Output I/O Synchronous VDD, VDDQ Core Power, I/O Power Supply Static VSS Ground Supply Static 4875 tbl 01 1 ©2004 Integrated Device Technology, Inc. OCTOBER 2004 DSC-4875/08 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Pin Definitions(1) Symbol Pin Function I/O Active Description A0-A17 Address Inputs I N/A Synchronous Address inputs. The address register is triggered by a combination of the rising edge of CLK, ADV/LD low, CEN low, and true chip enables. ADV/LD Advance / Load I N/A ADV/LD is a synchronous input that is used to load the internal reg isters with new address and control when it is sampled low at the rising edge of clock with the chip selected. When ADV/ LD is low with the chip deselected, any burst in progress is terminated. When ADV/LD is sampled high then the internal burst counter is advanced for any burst that was in progress. The external addresses are ignored when ADV/LD is sampled high. R/W Read / Write I N/A R/W signal is a synchronous input that identifies whether the current load cycle initiated is a Read or Write access to the memory array. The data bus activity for the current cycle takes place two clock cycles later. CEN Clock Enable I LOW Synchronous Clock Enable Input. When CEN is sampled high, all other synchronous inputs, including clock are ignored and outputs remain unchanged. The effect of CEN sampled high on the device outputs is as if the low to high clock transition did not occur. For normal operation, CEN must be sampled low at rising edge of clock. BW 1-BW 4 Individual Byte Write Enables I LOW Synchronous byte write enables. Each 9-bit byte has its own active low byte write enable. On load write cycles (When R/W and ADV/LD are sampled low) the appropriate byte write signal (BW 1-BW 4) must be valid. The byte write signal must also be valid on each cycle of a burst write. Byte Write signals are ignored when R/W is sampled high. The appropriate byte(s) of data are written into the device two cycles later. BW 1-BW 4 can all be tied low if always doing write to the entire 36-bit word. CE1, CE2 Chip Enables I LOW Sy nchronous active low chip enable. CE1 and CE2 are used with CE2 to enable the IDT71V2556/58. (CE1 or CE2 sampled high or CE 2 sampled low) and ADV/LD low at the rising edge of clock, initiates a deselect cycle. The ZBTTM has a two cycle deselect, i.e., the data bus will tri-state two clock cycles after deselect is initiated. CE2 Chip Enable I HIGH Synchronous active high chip enable. CE2 is used with CE1 and CE2 to enable the chip. CE 2 has inverted polarity but otherwise identical to CE1 and CE2. CLK Clock I N/A This is the clock input to the IDT71V2556/58. Except for OE, all timing referenc es for the device are made with respect to the rising edge of CLK. I/O0-I/O31 I/OP1-I/OP4 Data Input/Output I/O N/A Synchronous data input/output (I/O) pins. Both the data input path and data output path are registered and triggered by the rising edge of CLK. LBO Linear Burst Order I LOW Burst order selection input. When LBO is high the Interleaved burst sequence is selected. When LBO is low the Linear burst sequence is selected. LBO is a static input and it must not change during device operation. OE Output Enable I LOW Asynchronous output enable. OE must be low to read data from the 71V2556/58. When OE is high the I/O pins are in a high-impedance state. OE does not need to be actively controlled for read and write cycles. In normal operation, OE can be tied low. TMS Test Mode Select I N/A Gives input command for TAP controller. Sampled on rising edge of TDK. This pin has an internal pullup. TDI Test Data Input I N/A Serial input of registers placed between TDI and TDO. Sampled on rising edge of TCK. This pin has an internal pullup. TCK Test Clock I N/A Clock input of TAP controller. Each TAP event is clocked. Test inputs are captured on rising edge of TCK, while test outputs are driven from the falling edge of TCK. This pin has an internal pullup. TDO Test Data Output O N/A Serial output of registers placed between TDI and TDO. This output is active depe nding on the state of the TAP controller. TRST JTAG Reset (Optional) I LOW Optional Asynchronous JTAG reset. Can be used to reset the TAP controller, but not required. JTAG reset occurs automatically at power up and also resets using TMS and TCK per IEEE 1149.1. If not used TRST can be left floating. This pin has an internal pullup. ZZ Sleep Mode I HIGH Synchronous sleep mode input. ZZ HIGH will gate the CLK internally and power down the IDT71V2556/2558 to its lowest power consumption level. Data retention is guaranteed in Sleep Mode. This pin has an internal pulldown VDD Power Supply N/A N/A 3.3V core power supply. VDDQ Power Supply N/A N/A 2.5V I/O Supply. VSS Ground N/A N/A Ground. 4875 tbl 02 NOTE: 1. All synchronous inputs must meet specified setup and hold times with respect to CLK. 6.42 2 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Functional Block Diagram LBO Address A [0:16] 128Kx36 BIT MEMORY ARRAY D Q Address D Q Control CE1, CE2, CE2 R/W Input Register CEN ADV/LD BWx D DI DO Control Logic Q Clk Mux Sel D Clk Clock Output Register Q Gate OE 4875 drw 01a TMS TDI TCK TRST JTAG (SA Version) TDO (optional) 6.42 3 Data I/O [0:31], I/O P[1:4] , IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Functional Block Diagram LBO 256x18 BIT MEMORY ARRAY Address A [0:17] D Q Address D Q Control CE1, CE2, CE2 R/W Input Register CEN ADV/LD BWx DI D Q DO Control Logic Clk Mux Sel D Clk Clock Output Register Q Gate OE 4875 drw 01b TMS TDI TCK TRST JTAG (SA Version) TDO (optional) Recommended DC Operating Conditions Symbol Min. Typ. Max. Unit VDD Core Supply Voltage 3.135 3.3 3.465 V VDDQ I/O Supply Voltage 2.375 2.5 2.625 V VSS Supply Voltage 0 0 0 V 1.7 ____ VDD +0.3 1.7 ____ VIH VIH VIL Parameter Input High Voltage - Inputs Input High Voltage - I/O Input Low Voltage (1) -0.3 ____ (2) VDDQ +0.3 0.7 V V V 4875 tbl 03 NOTES: 1. VIL (min.) = –1.0V for pulse width less than tCYC /2, once per cycle. 2. VIH (max.) = +6.0V for pulse width less than tCYC/2, once per cycle. 6.42 4 Data I/O [0:15], I/O P[1:2] IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Recommended Operating Temperature and Supply Voltage Grade Temperature(1) VSS VDD VDDQ Commercial 0°C to +70°C 0V 3.3V± 5% 2.5V± 5% Industrial -40°C to +85°C 0V 3.3V± 5% 2.5V± 5% 4875 tbl 05 NOTES: 1. TA is the "instant on" case temperature. A6 A7 CE1 CE2 BW4 BW3 BW2 BW1 CE2 VDD VSS CLK R/W CEN OE ADV/LD NC(2) NC(2) A8 A9 Pin Configuration 128K x 36 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 I/OP3 I/O16 I/O17 VDDQ VSS I/O18 I/O19 I/O20 I/O21 VSS VDDQ I/O22 I/O23 VDD(1) VDD VDD(1) VSS I/O24 I/O25 VDDQ VSS I/O26 I/O27 I/O28 I/O29 VSS VDDQ I/O30 I/O31 I/OP4 1 80 2 79 3 78 77 4 5 6 76 75 7 74 8 73 9 72 71 10 11 70 12 69 13 68 14 67 15 66 16 65 64 17 18 19 63 62 20 61 21 60 22 59 23 24 58 57 25 56 26 55 27 54 53 28 29 52 51 30 I/OP2 I/O15 I/O14 VDDQ VSS I/O13 I/O12 I/O11 I/O10 VSS VDDQ I/O9 I/O8 VSS VDD(1) VDD VSS/ZZ(3) I/O7 I/O6 VDDQ VSS I/O5 I/O4 I/O3 I/O2 VSS VDDQ I/O1 I/O0 I/OP1 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 , LBO A5 A4 A3 A2 A1 A0 NC NC VSS VDD NC NC A10 A11 A12 A13 A14 A15 A16 4875 drw 02 Top View TQFP NOTES: 1. Pins 14, 16 and 66 do not have to be connected directly to VDD as long as the input voltage is ≥ VIH. 2. Pins 83 and 84 are reserved for future 8M and 16M respectively. 3. Pin 64 does not have to be connected directly to V SS as long as the input voltage is ≤ VIL; on the latest die revision this pin supports ZZ (sleep mode). 6.42 5 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Absolute Maximum Ratings(1) CE2 NC NC BW2 BW1 CE2 VDD VSS CLK R/W CEN OE ADV/LD NC(2) NC(2) A8 A9 A6 A7 CE1 Pin Configuration 256K x 18 Symbol 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 NC NC NC 1 80 2 79 3 VDDQ VSS NC NC I/O8 I/O9 VSS VDDQ I/O10 I/O11 VDD(1) VDD VDD(1) VSS I/O12 I/O13 VDDQ VSS I/O14 I/O15 I/OP2 NC VSS VDDQ NC NC NC 4 78 77 5 6 76 75 7 74 8 73 9 10 72 71 11 70 12 69 13 68 14 67 15 66 16 65 64 17 18 19 63 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 54 28 53 29 52 51 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 A10 NC NC VDDQ VSS NC I/OP1 I/O7 I/O6 VSS VDDQ I/O5 I/O4 VSS VDD(1) VDD VSS/ZZ(3) I/O3 I/O2 VDDQ VSS I/O1 I/O0 NC NC VSS VDDQ NC NC NC Commercial & Industrial Values Unit VTERM(2) Terminal Voltage with Respect to GND -0.5 to +4.6 V VTERM(3,6) Terminal Voltage with Respect to GND -0.5 to VDD V VTERM(4,6) Terminal Voltage with Respect to GND -0.5 to VDD +0.5 V VTERM(5,6) Terminal Voltage with Respect to GND -0.5 to VDDQ +0.5 V TA , Rating Commerical Operating Temperature -0 to +70 o C Industrial Operating Temperature -40 to +85 o C (7) TBIAS Temperature Under Bias -55 to +125 o C TSTG Storage Temperature -55 to +125 o C PT Power Dissipation 2.0 IOUT DC Output Current 50 W mA 4875 tbl 06 LBO A5 A4 A3 A2 A1 A0 NC NC VSS VDD NC NC A11 A12 A13 A14 A15 A16 A17 4875 drw 02a Top View TQFP NOTES: 1. Pins 14, 16 and 66 do not have to be connected directly to VDD as long as the input voltage is ≥ VIH . 2. Pins 83 and 84 are reserved for future 8M and 16M respectively. 3. Pin 64 does not have to be connected directly to VSS as long as the input voltage is ≤ VIL; on the latest die revision this pin supports ZZ (sleep mode). NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VDD terminals only. 3. VDDQ terminals only. 4. Input terminals only. 5. I/O terminals only. 6. This is a steady-state DC parameter that applies after the power supply has reached its nominal operating value. Power sequencing is not necessary; however, the voltage on any input or I/O pin cannot exceed VDDQ during power supply ramp up. 7. TA is the "instant on" case temperature. 100 TQFP Capacitance(1) (TA = +25° C, f = 1.0MHz) Symbol Parameter(1) CIN Input Capacitance CI/O I/O Capacitance Conditions Max. Unit VIN = 3dV 5 pF VOUT = 3dV 7 pF 119 BGA Capacitance(1) (TA = +25° C, f = 1.0MHz) Symbol 4875 tbl 07 165 fBGA Capacitance (1) (TA = +25° C, f = 1.0MHz) Symbol Parameter (1) CIN Input Capacitance CI/O I/O Capacitance Parameter(1) CIN Input Capacitance CI/O I/O Capacitance Conditions Max. Unit VIN = 3dV 7 pF VOUT = 3dV 7 pF 4875 tbl 07a Conditions Max. Unit VIN = 3dV TBD pF VOUT = 3dV TBD pF 4875 tb l 07b NOTE: 1. This parameter is guaranteed by device characterization, but not production tested. 6.42 6 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Pin Configuration 128K x 36, 119 BGA 1 2 3 4 5 6 7 A VDDQ A6 A4 NC(2) A8 A16 VDDQ B NC CE 2 A3 ADV/LD A9 CE2 NC C NC A7 A2 VDD A12 A15 NC D I/O16 I/OP3 VSS NC VSS I/OP2 I/O15 E I/O17 I/O18 VSS CE1 VSS I/O13 I/O14 F VDDQ I/O19 VSS OE VSS I/O12 VDDQ G I/O20 I/O21 BW3 NC(2) BW 2 I/O11 I/O10 H I/O22 I/O23 VSS R/W VSS I/O9 I/O8 J VDDQ VDD VDD(1) VDD VDD(1) VDD VDDQ K I/O24 I/O26 VSS CLK VSS I/O6 I/O7 L I/O25 I/O27 BW4 NC BW1 I/O4 I/O5 M VDDQ I/O28 VSS CEN VSS I/O3 VDDQ N I/O29 I/O30 VSS A1 VSS I/O2 I/O1 P I/O31 I/OP4 VSS A0 VSS I/OP1 I/O 0 R NC A5 LBO VDD A13 NC T NC NC A10 A11 NC NC/ZZ(5) U VDDQ NC/TMS(3) NC/TDI(3) VDD(1) A14 , NC/TCK(3) NC/TDO(3) NC/TRST (3,4) VDDQ 4875 drw 13a Top View Pin Configuration 256K x 18, 119 BGA 1 2 3 4 5 6 7 NC(2) A8 A16 VDDQ ADV/LD A9 CE2 NC VDD A13 A17 NC A VDDQ A6 A4 B NC CE2 A3 C NC A7 A2 D I/O8 NC VSS NC VSS I/OP1 NC E NC I/O9 VSS CE1 VSS NC I/O7 VSS OE VSS I/O6 VDDQ NC I/O5 F VDDQ NC G NC I/O10 BW2 NC(2) VSS H I/O11 NC VSS R/W VSS I/O4 NC J VDDQ VDD VDD(1) VDD VDD(1) VDD VDDQ K NC I/O12 VSS CLK VSS NC I/O3 L I/O13 NC VSS NC BW1 I/O2 NC M VDDQ I/O14 VSS CEN VSS NC VDDQ N I/O15 NC VSS A1 VSS I/O1 NC P NC I/OP2 VSS A0 VSS NC I/O0 R NC A5 LBO VDD VDD(1) A12 NC T NC A10 A15 NC A14 A11 NC/ZZ(5) U VDDQ NC/TMS(3) NC/TDI(3) NC/TCK(3) NC/TDO(3) Top View , NC/TRST (3,4) VDDQ 4875 drw 13b NOTES: 1. J3, J5, and R5 do not have to be directly connected to VDD as long as the input voltage is ≥ VIH. 2. G4 and A4 are reserved for future 8M and 16M respectively. 3. These pins are NC for the "S" version and the JTAG signal listed for the "SA" version. 4. TRST is offered as an optional JTAG reset if required in the application. If not needed, can be left floating and will internally be pulled to VDD. 5. Pin T7 supports ZZ (sleep mode) on the latest die revision. 6.42 7 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Pin Configuration 128K x 36, 165 fBGA 1 2 3 4 5 6 7 8 9 10 11 A NC(2) A7 CE1 BW 3 BW 2 C E2 CEN ADV/LD NC(2) A8 NC B NC A6 CE2 BW 4 BW 1 CLK R/W OE NC(2) A9 NC(2) C I/OP3 NC VDDQ VSS VSS VSS VSS VSS VDDQ NC I/OP2 D I/O17 I/O16 VDDQ VDD VSS VSS VSS VDD VDDQ I/O15 I/O14 E I/O19 I/O18 VDDQ VDD VSS VSS VSS VDD VDDQ I/O13 I/O12 F I/O21 I/O20 VDDQ VDD VSS VSS VSS VDD VDDQ I/O11 I/O10 G I/O23 I/O22 VDDQ VDD VSS VSS VSS VDD VDDQ I/O9 I/O8 H VDD(1) VDD(1) NC VDD VSS VSS VSS VDD NC NC NC/ZZ(5) J I/O25 I/O24 VDDQ VDD VSS VSS VSS VDD VDDQ I/O7 I/O6 K I/O27 I/O26 VDDQ VDD VSS VSS VSS VDD VDDQ I/O5 I/O4 L I/O29 I/O28 VDDQ VDD VSS VSS VSS VDD VDDQ I/O3 I/O2 M I/O31 I/O30 VDDQ VDD VSS VSS VSS VDD VDDQ I/O1 I/O0 N I/OP4 NC VDDQ VSS NC/TRST (3,4) NC VDD(1) VSS VDDQ NC I/OP1 P NC NC(2) A5 A2 NC/TDI(3) A1 NC/TDO(3) A10 A13 A14 NC R LBO (2) A0 (3) A11 A12 A15 NC A4 A3 NC/TMS (3) NC/TCK A16 4875 tbl 25 Pin Configuration 256K x 18, 165 fBGA 1 A (2) NC 2 3 4 5 6 7 A7 C E1 8 BW 2 NC C E2 CEN ADV/LD 9 10 11 (2) A8 A10 (2) NC B NC A6 CE2 NC BW 1 CLK R/W OE NC A9 NC(2) C NC NC VDDQ VSS VSS VSS VSS VSS VDDQ NC I/OP1 D NC I/O8 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O7 E NC I/O9 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O6 F NC I/O10 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O5 G NC I/O11 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O4 NC VDD VSS VSS VSS VDD NC NC NC/ZZ(5) H (1) VDD VDD J I/O12 NC VDDQ VDD VSS VSS VSS VDD VDDQ I/O3 NC K I/O13 NC VDDQ VDD VSS VSS VSS VDD VDDQ I/O2 NC L I/O14 NC VDDQ VDD VSS VSS VSS VDD VDDQ I/O1 NC M I/O15 NC VDDQ VDD VSS VSS VSS VDD VDDQ I/O0 NC N I/OP2 NC VDDQ VSS P NC R LBO (1) (2) NC (2) NC A5 A4 A2 A3 NC/TRST (3,4) (3) NC/TDI NC/TMS (3) NC A1 A0 (1) VDD VSS VDDQ NC NC (3) A11 A14 A15 NC (3) A12 A13 A16 NC/TDO NC/TCK A17 4875 tbl 25a NOTES: 1. H1, H2, and N7 do not have to be directly connected to VDD as long as the input voltage is ≥ VIH. 2. A9, B9, B11, A1, R2 and P2 are reserved for future 9M, 18M, 36M, 72M, 144M, and 288M respectively respectively. 3. These pins are NC for the "S" version and the JTAG signal listed for the "SA" version. 4. TRST is offered as an optional JTAG reset if required in the application. If not needed, can be left floating and will internally be pulled to VDD. 5. Pin H11 supports ZZ (sleep mode) on the latest die revision. 6.42 8 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Synchronous Truth Table(1) CEN R/W Chip(5) Enable ADV/ LD BWx ADDRESS USED PREVIOUS CYCLE CURRENT CYCLE I/O (2 cycles later) L L Select L Valid External X LOAD WRITE D(7) L H Select L X External X LOAD READ Q(7) L X X H Valid Internal LOAD WRITE / BURST WRITE BURST WRITE (Advance burst counter)(2) D(7) L X X H X Internal LOAD READ / BURST READ BURST READ (Advance burst counter)(2) Q(7) L X Deselect L X X X DESELECT or STOP(3) HiZ L X X H X X DESELECT / NOOP NOOP HiZ H X X X X X X SUSPEND(4) Previous Value 4875 tbl 08 NOTES: 1. L = V IL, H = VIH, X = Don’t Care. 2. When ADV/LD signal is sampled high, the internal burst counter is incremented. The R/W signal is ignored when the counter is advanced. Therefore the nature of the burst cycle (Read or Write) is determined by the status of the R/W signal when the first address is loaded at the beginning of the burst cycle. 3. Deselect cycle is initiated when either (CE1, or CE2 is sampled high or CE2 is sampled low) and ADV/LD is sampled low at rising edge of clock. The data bus will tri-state two cycles after deselect is initiated. 4. When CEN is sampled high at the rising edge of clock, that clock edge is blocked from propogating through the part. The state of all the internal registers and the I/ Os remains unchanged. 5. To select the chip requires CE1 = L, CE2 = L, CE 2 = H on these chip enables. Chip is deselected if any one of the chip enables is false. 6. Device Outputs are ensured to be in High-Z after the first rising edge of clock upon power-up. 7. Q - Data read from the device, D - data written to the device. Partial Truth Table for Writes(1) R/W BW1 BW2 BW3(3) BW4(3) READ H X X X X WRITE ALL BYTES L L L L L WRITE BYTE 1 (I/O[0:7], I/OP1)(2) L L H H H OPERATION WRITE BYTE 2 (I/O[8:15], I/OP2)(2) L H L H H (2,3) L H H L H (2,3) WRITE BYTE 4 (I/O[24:31], I/OP4) L H H H L NO WRITE L H H H H WRITE BYTE 3 (I/O[16:23], I/OP3) 4875 tbl 09 NOTES: 1. L = VIL, H = VIH, X = Don’t Care. 2. Multiple bytes may be selected during the same cycle. 3. N/A for X18 configuration. 6.42 9 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Interleaved Burst Sequence Table (LBO=VDD) Sequence 1 Sequence 2 Sequence 3 Sequence 4 A1 A0 A1 A0 A1 A0 A1 A0 First Address 0 0 0 1 1 0 1 1 Second Address 0 1 0 0 1 1 1 0 Third Address 1 0 1 1 0 0 0 1 1 1 1 0 0 1 0 0 Fourth Address (1) 4875 tbl 10 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state and continues counting. Linear Burst Sequence Table (LBO=VSS) Sequence 1 Sequence 2 Sequence 3 Sequence 4 A1 A0 A1 A0 A1 A0 A1 A0 First Address 0 0 0 1 1 0 1 1 Second Address 0 1 1 0 1 1 0 0 Third Address 1 0 1 1 0 0 0 1 1 1 0 0 0 1 1 0 Fourth Address (1) 4875 tbl 11 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state and continues counting. Functional Timing Diagram(1) CYCLE n+29 n+30 n+31 n+32 n+33 n+34 n+35 n+36 n+37 A29 A30 A31 A32 A33 A34 A35 A36 A37 C29 C30 C31 C32 C33 C34 C35 C36 C37 D/Q27 D/Q28 D/Q29 D/Q30 D/Q31 D/Q32 D/Q33 D/Q34 D/Q35 CLOCK (2) ADDRESS (A0 - A16) (2) CONTROL (R/W, ADV/LD, BWx) (2) DATA I/O [0:31], I/O P[1:4] 4875 drw 03 NOTES: 1. This assumes CEN, CE1, CE2, CE2 are all true. 2. All Address, Control and Data_In are only required to meet set-up and hold time with respect to the rising edge of clock. Data_Out is valid after a clock-to-data delay from the rising edge of clock. 6.42 10 , IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Device Operation - Showint Mixed Load, Burst, Deselect and NOOP Cycles(2) Cycle Address R/ W ADV/LD CE(1) CEN BWx OE I/O Comments n A0 H L L L X X X Load read n+1 X X H X L X X X Burst read n+2 A1 H L L L X L Q0 Load read n+3 X X L H L X L Q0+1 n+4 X X H X L X L Q1 NOOP n+5 A2 H L L L X X Z Load read n+6 X X H X L X X Z Burst read n+7 X X L H L X L Q2 Deselect or STOP n+8 A3 L L L L L L Q2+1 Load write n+9 X X H X L L X Z Burst write n+10 A4 L L L L L X D3 Load write n+11 X X L H L X X D3+1 n+12 X X H X L X X D4 NOOP n+13 A5 L L L L L X Z Load write n+14 A6 H L L L X X Z Load read n+15 A7 L L L L L X D5 Load write n+16 X X H X L L L Q6 Burst write n+17 A8 H L L L X X D7 Load read n+18 X X H X L X X D7+1 Burst read n+19 A9 L L L L L L Q8 Load write Deselect or STOP Deselect or STOP 4875 tbl 12 NOTES: 1. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 2. H = High; L = Low; X = Don’t Care; Z = High Impedance. Read Operation(1) Cycle Address R/ W ADV/LD CE(2) CEN BWx OE I/O Comments n A0 H L L L X X X Address and Control meet setup n+1 X X X X L X X X Clock Setup Valid n+2 X X X X X X L Q0 Contents of Address A0 Read Out 4875 tbl 13 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 6.42 11 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Burst Read Operation(1) Cycle Address R/ W ADV/LD CE(2) CEN BWx OE I/O Comments n A0 H L L L X X X Address and Control meet setup n+1 X X H X L X X X Clock Setup Valid, Advance Counter n+2 X X H X L X L Q0 Address A0 Read Out, Inc. Count n+3 X X H X L X L Q0+1 Address A0+1 Read Out, Inc. Count n+4 X X H X L X L Q0+2 Address A0+2 Read Out, Inc. Count n+5 A1 H L L L X L Q0+3 Address A0+3 Read Out, Load A1 n+6 X X H X L X L Q0 Address A0 Read Out, Inc. Count n+7 X X H X L X L Q1 Address A1 Read Out, Inc. Count n+8 A2 H L L L X L Q1+1 Address A1+1 Read Out, Load A2 4875 tbl 14 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance.. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. Write Operation(1) Cycle Address R/ W ADV/LD CE(2) CEN BWx OE I/O Comments n A0 L L L L L X X Address and Control meet setup n+1 X X X X L X X X Clock Setup Valid n+2 X X X X L X X D0 Write to Address A0 4875 tbl 15 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. Burst Write Operation(1) Cycle Address R/ W ADV/LD CE(2) CEN BWx OE I/O Comments n A0 L L L L L X X Address and Control meet setup n+1 X X H X L L X X Clock Setup Valid, Inc. Count n+2 X X H X L L X D0 Address A0 Write, Inc. Count n+3 X X H X L L X D0+1 Address A0+1 Write, Inc. Count n+4 X X H X L L X D0+2 Address A0+2 Write, Inc. Count n+5 A1 L L L L L X D0+3 Address A0+3 Write, Load A1 n+6 X X H X L L X D0 Address A0 Write, Inc. Count n+7 X X H X L L X D1 Address A1 Write, Inc. Count n+8 A2 L L L L L X D1+1 Address A1+1 Write, Load A2 NOTES: 1. H = High; L = Low; X = Don’t Care; ? = Don’t Know; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 6.42 12 4875 tbl 16 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Read Operation with Clock Enable Used(1) Cycle Address R/ W ADV/LD CE(2) CEN BWx OE I/O Comments n A0 H L L L X X X Address and Control meet setup n+1 X X X X H X X X Clock n+1 Ignored n+2 A1 H L L L X X X Clock Valid n+3 X X X X H X L Q0 Clock Ignored. Data Q0 is on the bus. n+4 X X X X H X L Q0 Clock Ignored. Data Q0 is on the bus. n+5 A2 H L L L X L Q0 Address A0 Read out (bus trans.) n+6 A3 H L L L X L Q1 Address A1 Read out (bus trans.) n+7 A4 H L L L X L Q2 Address A2 Read out (bus trans.) 4875 tbl 17 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. Write Operation with Clock Enable Used(1) Cycle Address R/ W ADV/LD CE(2) CEN BWx OE I/O Comments n A0 L L L L L X X Address and Control meet setup. n+1 X X X X H X X X Clock n+1 Ignored. n+2 A1 L L L L L X X Clock Valid. n+3 X X X X H X X X Clock Ignored. n+4 X X X X H X X X Clock Ignored. n+5 A2 L L L L L X D0 Write Data D0 n+6 A3 L L L L L X D1 Write Data D1 n+7 A4 L L L L L X D2 Write Data D2 4875 tbl 18 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 6.42 13 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Read Operation with Chip Enable Used(1) Cycle Address R/ W ADV/LD CE(2) CEN BWx OE I/O(3) Comments n X X L H L X X ? Deselected. n+1 X X L H L X X ? Deselected. n+2 A0 H L L L X X Z Address and Control meet setup n+3 X X L H L X X Z Deselected or STOP. n+4 A1 H L L L X L Q0 Address A0 Read out. Load A 1. n+5 X X L H L X X Z Deselected or STOP. n+6 X X L H L X L Q1 Address A1 Read out. Deselected. n+7 A2 H L L L X X Z Address and control meet setup. n+8 X X L H L X X Z Deselected or STOP. n+9 X X L H L X L Q2 Address A2 Read out. Deselected. 4875 tbl 19 NOTES: 1. H = High; L = Low; X = Don’t Care; ? = Don’t Know; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE 2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 3. Device Outputs are ensured to be in High-Z after the first rising edge of clock upon power-up. Write Operation with Chip Enable Used(1) Cycle Address R/ W ADV/LD CE(2) CEN BWx OE I/O(3) Comments n X X L H L X X ? Deselected. n+1 X X L H L X X ? Deselected. n+2 A0 L L L L L X Z Address and Control meet setup n+3 X X L H L X X Z Deselected or STOP. n+4 A1 L L L L L X D0 Address D0 Write in. Load A 1. n+5 X X L H L X X Z Deselected or STOP. n+6 X X L H L X X D1 Address D1 Write in. Deselected. n+7 A2 L L L L L X Z Address and control meet setup. n+8 X X L H L X X Z Deselected or STOP. n+9 X X L H L X X D2 Address D2 Write in. Deselected. NOTES: 1. H = High; L = Low; X = Don’t Care; ? = Don’t Know; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 6.42 14 4875 tbl 20 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 3.3V±5%) Symbol Parameter Test Conditions Min. Max. Unit |ILI| Input Leakage Current VDD = Max., VIN = 0V to V DD ___ 5 µA |ILI| LBO, JTAG and ZZ Input Leakage Current(1) VDD = Max., VIN = 0V to V DD ___ 30 µA |ILO| Output Leakage Current VOUT = 0V to V DDQ, Device Deselected ___ 5 µA VOL Output Low Voltage IOL = +6mA, VDD = Min. ___ 0.4 V 2.0 ___ V VOH Output High Voltage IOH = -6mA, VDD = Min. 4875 tbl 21 NOTE: 1. The LBO, TMS, TDI, TCK & TRST pins will be internally pulled to VDD and ZZ will be internally pulled to VSS if it is not actively driven in the application. DC Electrical Characteristics Over the Operating Temperature Supply Voltage Range (1) (VDD = 3.3V±5%) 200MHz 166MHz 133MHz 100MHz Unit Symbol Parameter Test Conditions Com'l Only Com'l Ind Com'l Ind Com'l Ind IDD Operating Power Supply Current Device Selected, Outputs Open, ADV/ LD = X, V DD = Max., VIN > VIH or < VIL, f = fMAX(2) 400 350 360 300 310 250 260 mA ISB1 Device Deselected, Outputs CMOS Standby Power Supply Current Open, VDD = Max., VIN > VHD or < VLD, f = 0(2,3) 40 40 45 40 45 40 45 mA ISB2 Clock Running Power Supply Current Device Deselected, Outputs Open, VDD = Max., VIN > VHD or < VLD, f = fMAX(2.3) 130 120 130 110 120 100 110 mA ISB3 Idle Power Supply Current Device Selected, Outputs Open, CEN > VIH, VDD = Max., VIN > VHD or < VLD, f = fMAX(2,3) 40 40 45 40 45 40 45 mA 4875 tbl 22 NOTES: 1. All values are maximum guaranteed values. 2. At f = fMAX, inputs are cycling at the maximum frequency of read cycles of 1/tCYC; f=0 means no input lines are changing. 3. For I/Os VHD = VDDQ – 0.2V, VLD = 0.2V. For other inputs VHD = VDD – 0.2V, VLD = 0.2V. AC Test Loads AC Test Conditions VDDQ/2 (VDDQ = 2.5V) 50Ω I/O Z0 = 50Ω , Input Rise/Fall Times 4875 drw 04 6 Figure 1. AC Test Load 5 Input Pulse Levels 4 2ns Input Timing Reference Levels (VDDQ/2) Output Timing Reference Levels (VDDQ/2) AC Test Load ∆tCD 3 (Typical, ns) 2 0 to 2.5V See Figure 1 4875 tbl 23 1 20 30 50 80 100 Capacitance (pF) 200 4875 drw 05 , Figure 2. Lumped Capacitive Load, Typical Derating 6.42 15 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges AC Electrical Characteristics (VDD = 3.3V±5%, Commercial and Industrial Temperature Ranges) 200MHz Symbol Parameter 166MHz 133MHz 100MHz Min. Max. Min. Max. Min. Max. Min. Max. Unit tCYC Clock Cycle Time 5 ____ 6 ____ 7.5 ____ 10 ____ ns tF(1) Clock Frequence ____ 200 ____ 166 ____ 133 ____ 100 MHz tCH(2) Clock High Pulse Width 1.8 ____ 1.8 ____ 2.2 ____ 3.2 ____ ns tCL(2) Clock Low Pulse Width 1.8 ____ 1.8 ____ 2.2 ____ 3.2 ____ ns ____ 3.2 ____ 3.5 ____ 4.2 ____ 5 ns Output Parameters tCD Clock High to Valid Data tCDC Clock High to Data Change 1 ____ 1 ____ 1 ____ 1 ____ ns tCLZ(3,4,5) Clock High to Output Active 1 ____ 1 ____ 1 ____ 1 ____ ns tCHZ(3,4,5) Clock High to Data High-Z 1 3 1 3 1 3 1 3 ns tOE Output Enable Access Time ____ 3.2 ____ 3.5 ____ 4.2 ____ 5 ns tOLZ(3,4) Output Enable Low to Data Active 0 ____ 0 ____ 0 ____ 0 ____ ns tOHZ(3,4) Output Enable High to Data High-Z ____ 3.5 ____ 3.5 ____ 4.2 ____ 5 ns 1.5 ____ 1.5 ____ 1.7 ____ 2.0 ____ ns 1.5 ____ 1.5 ____ 1.7 ____ 2.0 ____ ns 1.5 ____ 1.7 ____ 2.0 ____ ns Set Up Times tSE tSA Clock Enable Setup Time Address Setup Time tSD Data In Setup Time 1.5 ____ tSW Read/Write (R/ W) Setup Time 1.5 ____ 1.5 ____ 1.7 ____ 2.0 ____ ns tSADV Advance/Load (ADV/LD) Setup Time 1.5 ____ 1.5 ____ 1.7 ____ 2.0 ____ ns tSC Chip Enable/Select Setup Time 1.5 ____ 1.5 ____ 1.7 ____ 2.0 ____ ns tSB Byte Write Enable (BWx) Setup Time 1.5 ____ 1.5 ____ 1.7 ____ 2.0 ____ ns tHE Clock Enable Hold Time 0.5 ____ 0.5 ____ 0.5 ____ 0.5 ____ ns tHA Address Hold Time 0.5 ____ 0.5 ____ 0.5 ____ 0.5 ____ ns tHD Data In Hold Time 0.5 ____ 0.5 ____ 0.5 ____ 0.5 ____ ns tHW Read/Write (R/ W) Hold Time 0.5 ____ 0.5 ____ 0.5 ____ 0.5 ____ ns tHADV Advance/Load (ADV/LD) Hold Time 0.5 ____ 0.5 ____ 0.5 ____ 0.5 ____ ns tHC Chip Enable/Select Hold Time 0.5 ____ 0.5 ____ 0.5 ____ 0.5 ____ ns tHB Byte Write Enable (BWx) Hold Time 0.5 ____ 0.5 ____ 0.5 ____ 0.5 ____ ns Hold Times 4875 tbl 24 NOTES: 1. tF = 1/tCYC. 2. Measured as HIGH above 0.6VDDQ and LOW below 0.4VDDQ. 3. Transition is measured ±200mV from steady-state. 4. These parameters are guaranteed with the AC load (Figure 1) by device characterization. They are not production tested. 5. To avoid bus contention, the output buffers are designed such that tCHZ (device turn-off) is about 1ns faster than tCLZ (device turn-on) at a given temperature and voltage. The specs as shown do not imply bus contention because tCLZ is a Min. parameter that is worse case at totally different test conditions (0 deg. C, 3.465V) than tCHZ, which is a Max. parameter (worse case at 70 deg. C, 3.135V). 6.42 16 6.42 17 A1 tSADV tHA tHW tHE tCLZ tHC Pipeline Read tSC A2 tSA tSW tSE tCD Pipeline Read Q(A1) tHADV tCH tCDC tCL Q(A2) O1(A2) , O2(A2) Q(A 2+1) Q(A2+2) (CEN high, eliminates current L-H clock edge) Burst Pipeline Read tCD Q(A2+2) tCDC Q(A2+3) tCHZ Q(A2) 4875 drw 06 (Burst Wraps around to initial state) NOTES: 1. Q (A1) represents the first output from the external address A1. Q (A2) represents the first output from the external address A2; Q (A2+1) represents the next output data in the burst sequence of the base address A2, etc. where address bits A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Burst ends when new address and control are loaded into the SRAM by sampling ADV/LD LOW. 4. R/W is don't care when the SRAM is bursting (ADV/LD sampled HIGH). The nature of the burst access (Read or Write) is fixed by the state of the R/W signal when new address and control are loaded into the SRAM. DATAOUT OE BW1 - BW4 CE1, CE2 (2) ADDRESS R/W ADV/LD CEN CLK tCYC IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Timing Waveform of Read Cycle(1,2,3,4) (2) 6.42 18 A1 tSADV tHW tHE tHB tHC Pipeline Write tSB tSC tHA A2 tSA tSW tSE tHD Pipeline Write D(A1) tSD tHADV tCH , D(A2) tCL D(A2+1) Burst Pipeline Write (CEN high, eliminates current L-H clock edge) tSD D(A2+2) tHD D(A2) 4875 drw 07 D(A2+3) (Burst Wraps around to initial state) NOTES: 1. D (A1) represents the first input to the external address A1. D (A2) represents the first input to the external address A2; D (A2+1) represents the next input data in the burst sequence of the base address A2, etc. where address bits A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Burst ends when new address and control are loaded into the SRAM by sampling ADV/LD LOW. 4. R/W is don't care when the SRAM is bursting (ADV/LD sampled HIGH). The nature of the burst access (Read or Write) is fixed by the state of the R/W signal when new address and control are loaded into the SRAM. 5. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. DATAIN OE BW1 - BW4 CE1, CE2 ADDRESS R/W ADV/LD CEN CLK tCYC IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Timing Waveform of Write Cycles(1,2,3,4,5) 6.42 19 A1 tSADV tHW tHE tCD tHB tHC Read tSB tSC tHA A2 tSA tSW tSE A3 Q(A1) tCHZ Write tHADV tCH tCLZ Read D(A2) tSD tHD A4 tCL Q(A3) tCDC Write A5 D(A4) A6 Read D(A5) A7 Q(A6) A8 Q(A7) A9 4875 drw 08 , , NOTES: 1. Q (A1) represents the first output from the external address A1. D (A2) represents the input data to the SRAM corresponding to address A2. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. DATAOUT DATAIN OE BW1 - BW4 CE1, CE2(2) ADDRESS R/W ADV/LD CEN CLK tCYC IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Timing Waveform of Combined Read and Write Cycles (1,2,3) 6.42 20 A1 tSE tSADV tHE tHW tHB tHC tCD tCLZ B(A2) tSB tSC tHA A2 tSA tSW tCH tHADV tCYC Q(A1) tCL tCHZ tCDC Q(A1) A3 D(A2) tSD tHD A4 4875 drw 09 Q(A3) A5 , NOTES: 1. Q (A1) represents the first output from the external address A1. D (A2) represents the input data to the SRAM corresponding to address A2. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. CEN when sampled high on the rising edge of clock will block that L-H transition of the clock from propogating into the SRAM. The part will behave as if the L-H clock transition did not occur. All internal registers in the SRAM will retain their previous state. 4. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. DATAOUT DATAIN OE BW1 - BW4 CE1, CE2(2) ADDRESS R/W ADV/LD CEN CLK IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Timing Waveform of CEN Operation(1,2,3,4) 6.42 21 (2) A1 tSADV tHW tHE tSC tCLZ tCD tHC tHA A2 tSA tSW tSE Q(A1) tHADV tCH tCDC tCHZ tHB Q(A2) tSB A3 tCL D(A3) tSD tHD A4 Q(A4) A5 4875 drw 10 , NOTES: 1. Q (A1) represents the first output from the external address A1. D (A3) represents the input data to the SRAM corresponding to address A3. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. CEN when sampled high on the rising edge of clock will block that L-H transition of the clock from propogating into the SRAM. The part will behave as if the L-H clock transition did not occur. All internal registers in the SRAM will retain their previous state. 4. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. DATAOUT DATAIN OE BW1 - BW4 CE1, CE2 ADDRESS R/W ADV/LD CEN CLK tCYC IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Timing Waveform of CS Operation(1,2,3,4) IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges JTAG Interface Specification (SA Version only) tJF tJCL tJCYC tJR tJCH TCK Device Inputs(1)/ TDI/TMS tJS Device Outputs(2)/ TDO tJDC tJH tJRSR tJCD TRST(3) x M4875 drw 01 tJRST NOTES: 1. Device inputs = All device inputs except TDI, TMS and TRST. 2. Device outputs = All device outputs except TDO. 3. During power up, TRST could be driven low or not be used since the JTAG circuit resets automatically. TRST is an optional JTAG reset. JTAG AC Electrical Characteristics(1,2,3,4) Symbol Parameter Min. Max. Units ns tJCYC JTAG Clock Input Period 100 ____ tJCH JTAG Clock HIGH 40 ____ ns tJCL JTAG Clock Low 40 ____ ns tJR JTAG Clock Rise Time ____ 5(1) tJF JTAG Clock Fall Time ____ tJRST JTAG Reset tJRSR tJCD Scan Register Sizes Register Name Bit Size Instruction (IR) 4 ns Bypass (BYR) 1 5(1) ns JTAG Identification (JIDR) 50 ____ ns Boundary Scan (BSR) JTAG Reset Recovery 50 ____ ns JTAG Data Output ____ 20 ns ns ns tJDC JTAG Data Output Hold 0 ____ tJS JTAG Setup 25 ____ tJH JTAG Hold 25 ____ 32 Note (1) I4875 tbl 03 NOTE: 1. The Boundary Scan Descriptive Language (BSDL) file for this device is available by contacting your local IDT sales representative. ns I4875 tbl 01 NOTES: 1. Guaranteed by design. 2. AC Test Load (Fig. 1) on external output signals. 3. Refer to AC Test Conditions stated earlier in this document. 4. JTAG operations occur at one speed (10MHz). The base device may run at any speed specified in this datasheet. 6.42 22 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges JTAG Identification Register Definitions (SA Version only) Instruction Field Value Revision Number (31:28) Description 0x2 IDT Device ID (27:12) 0x210, 0x212 IDT JEDEC ID (11:1) 0x33 ID Register Indicator Bit (Bit 0) Reserved for version number. Defines IDT part number 71V2556SA and 71V2558SA, respectively. Allows unique identification of device vendor as IDT. 1 Indicates the presence of an ID register. I4875 tbl 02 Available JTAG Instructions Instruction Description OPCODE EXTEST Forces contents of the boundary scan cells onto the device outputs (1). Places the boundary scan register (BSR) between TDI and TDO. 0000 SAMPLE/PRELOAD Places the boundary scan register (BSR) between TDI and TDO. SAMPLE allows data from device inputs(2) and outputs(1) to be captured in the boundary scan cells and shifted serially through TDO. PRELOAD allows data to be input serially into the boundary scan cells via the TDI. 0001 DEVICE_ID Loads the JTAG ID register (JIDR) with the vendor ID code and places the register between TDI and TDO. 0010 HIGHZ Places the bypass register (BYR) between TDI and TDO. Forces all device o utput drivers to a High-Z state. 0011 RESERVED RESERVED RESERVED 0100 Several combinations are reserved. Do not use codes other than those identified for EXTEST, SAMPLE/PRELOAD, DEVICE_ID, HIGHZ, CLAMP, VALIDATE and BYPASS instructions. RESERVED CLAMP 0101 0110 0111 Uses BYR. Forces contents of the boundary scan cells onto the device outputs. Places the byp ass registe r (BYR) between TDI and TDO. RESERVED 1000 1001 RESERVED 1010 Same as above. RESERVED 1011 RESERVED 1100 VALIDATE Automatically loaded into the instruction register whenever the TAP controller passes through the CAPTURE-IR state. The lower two bits '01' are mand ated by the IEEE std. 1149.1 specification. 1101 RESERVED Same as above. 1110 BYPASS The BYPASS instruction is used to truncate the boundary scan register as a single bit in length. 1111 I4875 tbl 04 NOTES: 1. Device outputs = All device outputs except TDO. 2. Device inputs = All device inputs except TDI, TMS, and TRST. 6.42 23 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges 100 Pin Plastic Thin Quad Flatpack (TQFP) Package Diagram Outline 6.42 24 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges 119 Ball Grid Array (BGA) Package Diagram Outline 6.42 25 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges 165 Fine Pitch Ball Grid Array (fBGA) Package Diagram Outline 6.42 26 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Timing Waveform of OE Operation(1) OE tOE tOHZ tOLZ DATAOUT Valid 4875 drw 11 NOTE: 1. A read operation is assumed to be in progress. , Ordering Information IDT XXXX XX XX XX X Device Type Power Speed Package Process/ Temperature Range Blank I Commercial (0°C to +70°C) Industrial (-40°C to +85°C) PF** BG BQ 100-pin Plastic Thin Quad Flatpack (TQFP) 119 Ball Grid Array (BGA) 165 Fine Pitch Ball Grid Array (fBGA) 200* 166 133 100 Clock Frequency in Megahertz S SA Standard Power Standard Power with JTAG Interface IDT71V2556 IDT71V2558 128Kx36 Pipelined ZBT SRAM with 2.5V I/O 256Kx18 Pipelined ZBT SRAM with 2.5V I/O *Available for commercial temperature range only. ** JTAG (SA version) is not available with 100-pin TQFP package 6.42 27 , 4875 drw 12 IDT71V2556, IDT71V2558, 128K x 36, 256K x 18, 3.3V Synchronous ZBT™ SRAMs with 2.5V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Datasheet Document History 6/30/99 8/23/99 Pp. 4, 5 Pg. 6 Pg. 14 Pg. 15 10/4/99 Pg. 22 Pg. 24 Pg. 14 Pg. 15 12/31/99 04/30/00 Pg. 5,6 Pg. 6 Pg. 7 Pg. 21 05/26/00 07/26/00 Pg. 23 Pg. 5,6,7 Pg. 8 Pg. 23 10/25/00 5/20/02 10/15/04 Pg. 8 Pg. 1-8,15,22,23,27 Pg.7 Updated to new format Added Smart ZBT functionality Added Note 4 and changed Pins 38, 42, and 43 to DNU Changed U2–U6 to DNU Added Smart ZBT AC Electrical Characteristics Improved tCD and tOE(MAX) at 166MHz Revised tCHZ(MIN) for f ≤ 133 MHz Revised tOHZ (MAX) for f ≤ 133 MHz Improved tCH, tCL for f ≤ 166 MHz Improved setup times for 100–200 MHz Added BGA package diagrams Added Datasheet Document History Revised AC Electrical Characteristics table Revised tCHZ to match tCLZ and tCDC at 133MHz and 100MHz Removed Smart functionality Added Industrial Temperature range offerings at the 100 to 166MHz speed grades. Add clarification note to Recommended Temperature Ratings and Absolute Max Ratings table; Add note to TQFP Pin Configurations Add BGA Capacitance table Add note to BGA Pin Configurations Insert TQFP Package Diagram Outline Add new package offering, 13 x 15mm 165fBGA Correct 119 BGA Package Diagram Outline Add zz, sleep mode reference note to TQFP, BG119 and BQ165 pinouts Update BQ165 pinout Update BG119 package diagram outlines Remove Preliminary Status Add note to pin N5, BQ165 pinout reserved for JTAG TRST Added JTAG "SA" version functionality & updated ZZ pin descriptions and notes. Updated pin configuration for the 119 BGA - reordered I/O signals on P6, P7 (128K x 36) and P7, N6, L6, K7, H6, G7, F6, E7, D6 (256K x 18). CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com for Tech Support: [email protected] 800-544-7726 The IDT logo is a registered trademark of Integrated Device Technology, Inc. ZBT and ZeroBus Turnaround are trademarks of Integrated Device Technology, Inc. and the architecture is supported by Micron Technology and Motorola Inc. 6.42 28