1.6x0.2mm RIGHT ANGLE SMD CHIP LED LAMP ATTENTION Part Number: APGA1602QBC/KA-5MAV OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Blue Features Descriptions z 1.6mmx0.2mm right angle SMT LED,0.2mm thickness. z The Blue source color devices are made with InGaN on Sapphire-substrate Light Emitting Diode. z Low power consumption. z Electrostatic discharge and power surge could damage z Wide viewing angle. z Ideal for backlight and indicator. z Moisture sensitivity level : level 3. the LEDs. z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs. z Package :2000pcs / reel. z Tinned pads for improved solderability. z Low current IF=5mA operating. z All devices, equipments and machineries must be electrically grounded. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAN2013 REV NO: V.4B DATE: MAY/06/2015 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203013773 Selection Guide Part No. Dice APGA1602QBC/KA-5MAV Iv (mcd) [2] @ 5mA Lens Type Blue (InGaN) Water Clear Viewing Angle [1] Min. Typ. 2θ1/2 8 20 130°(H) 150°(V) Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Blue λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 460 nm IF=5mA Blue 463 nm IF=5mA Spectral Line Half-width Blue 25 nm IF=5mA VF [2] Forward Voltage Blue 2.8 3.2 V IF=5mA IR Reverse Current Blue 50 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Blue Units Power dissipation 70 mW DC Forward Current 20 mA Peak Forward Current [1] 100 mA Electrostatic Discharge Threshold(HBM) 250 V 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +100°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAN2013 REV NO: V.4B DATE: MAY/06/2015 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203013773 Blue APGA1602QBC/KA-5MAV SPEC NO: DSAN2013 REV NO: V.4B DATE: MAY/06/2015 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203013773 APGA1602QBC/KA-5MAV Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAN2013 REV NO: V.4B DATE: MAY/06/2015 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203013773 PACKING & LABEL SPECIFICATIONS APGA1602QBC/KA-5MAV Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAN2013 REV NO: V.4B DATE: MAY/06/2015 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203013773