SPANSION AM29LV640ML120RFI 64 megabit (4 m x 16-bit/8 m x 8-bit) mirrorbit 3.0 volt-only uniform sector flash memory with versatilei/o control Datasheet

Am29LV640MH/L
Data Sheet
RETIRED
PRODUCT
This product has been retired and is not available for designs. For new and current designs,
S29GL064A supersedes Am29LV640M H/L and is the factory-recommended migration path. Please
refer to the S29GL064A datasheet for specifications and ordering information. Availability of this
document is retained for reference and historical purposes only.
April 2005
The following document specifies Spansion memory products that are now offered by both Advanced
Micro Devices and Fujitsu. Although the document is marked with the name of the company that
originally developed the specification, these products will be offered to customers of both AMD and
Fujitsu.
Continuity of Specifications
There is no change to this datasheet as a result of offering the device as a Spansion product. Any
changes that have been made are the result of normal datasheet improvement and are noted in the
document revision summary, where supported. Future routine revisions will occur when appropriate, and changes will be noted in a revision summary.
For More Information
Please contact your local AMD or Fujitsu sales office for additional information about Spansion
memory solutions.
Publication Number 26191
Revision F
Amendment +3
Issue Date December 14, 2005
THIS PAGE LEFT INTENTIONALLY BLANK.
Am29LV640MH/L
64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit™
3.0 Volt-only Uniform Sector Flash Memory
with VersatileI/O™ Control
This product has been retired and is not available for designs. For new and current designs, S29GL064A supersedes Am29LV640M H/L and is the factory-recommended migration path.
Please refer to the S29GL064A datasheet for specifications and ordering information. Availability of this document is retained for reference and historical purposes only.
DISTINCTIVE CHARACTERISTICS
ARCHITECTURAL ADVANTAGES
„ Single power supply operation
— 3 V for read, erase, and program operations
„ VersatileI/O™ control
— Device generates data output voltages and tolerates
data input voltages on the DQ inputs/outputs as
determined by the voltage on the VIO pin; operates
from 1.65 to 3.6 V
„ Manufactured on 0.23 µm MirrorBit process
technology
„ SecSi™ (Secured Silicon) Sector region
— 128-word/256-byte sector for permanent, secure
identification through an 8-word/16-byte random
Electronic Serial Number, accessible through a
command sequence
— May be programmed and locked at the factory or by
the customer
„ Flexible sector architecture
— One hundred twenty-eight 32 Kword/64-Kbyte sectors
„ Compatibility with JEDEC standards
— Provides pinout and software compatibility for
single-power supply flash, and superior inadvertent
write protection
„ Minimum 100,000 erase cycle guarantee per sector
„ 20-year data retention at 125°C
PERFORMANCE CHARACTERISTICS
„ High performance
— 90 ns access time
— 25 ns page read times
— 0.5 s typical sector erase time
— 22 µs typical effective write buffer word programming
time: 16-word/32-byte write buffer reduces overall
programming time for multiple-word/byte updates
— 4-word/8-byte page read buffer
— 16-word/32-byte write buffer
„ Low power consumption (typical values at 3.0 V, 5
MHz)
— 30 mA typical active read current
— 50 mA typical erase/program current
— 1 µA typical standby mode current
„ Package options
— 56-pin TSOP
— 64-ball Fortified BGA
SOFTWARE FEATURES
— Program Suspend & Resume: read other sectors
before programming operation is completed
— Erase Suspend & Resume: read/program other
sectors before an erase operation is completed
— Data# polling & toggle bits provide status
— Unlock Bypass Program command reduces overall
multiple-word programming time
— CFI (Common Flash Interface) compliant: allows host
system to identify and accommodate multiple flash
devices
HARDWARE FEATURES
— Sector Group Protection: hardware-level method of
preventing write operations within a sector group
— Temporary Sector Unprotect: VID-level method of
changing code in locked sectors
— WP#/ACC input:
Write Protect input (WP#) protects first or last sector
regardless of sector protection settings
ACC (high voltage) accelerates programming time for
higher throughput during system production
— Hardware reset input (RESET#) resets device
— Ready/Busy# output (RY/BY#) indicates program or
erase cycle completion
This Data Sheet states AMD’s current technical specifications regarding the Products described herein. This Data
Sheet may be revised by subsequent versions or modifications due to changes in technical specifications.
Publication# 26191
Rev: F Amendment/3
Issue Date: December 14, 2005
Refer to AMD’s Website (www.amd.com) for the latest information.
D A T A S H E E T
GENERAL DESCRIPTION
The Am29LV640MH/L is a 64 Mbit, 3.0 volt single
power supply flash memory device organized as
4,194,304 words or 8,388,608 bytes. The device has
an 8-bit/16-bit bus and can be programmed either in
the host system or in standard EPROM programmers.
An access time of 90, 100, 110, or 120 ns is available.
Note that each access time has a specific operating
voltage range (VCC) and an I/O voltage range (VIO), as
specified in the Product Selector Guide and the Ordering Information sections. The device is offered in a
56-pin TSOP or 64-ball Fortified BGA package. Each
device has separate chip enable (CE#), write enable
(WE#) and output enable (OE#) controls.
Each device requires only a single 3.0 volt power
supply for both read and write functions. In addition to
a V CC input, a high-voltage accelerated program
(ACC) feature provides shorter programming times
through increased current on the WP#/ACC input. This
feature is intended to facilitate factory throughput during system production, but may also be used in the
field if desired.
The device is entirely command set compatible with
the JEDEC single-power-supply Flash standard.
Commands are written to the device using standard
microprocessor write timing. Write cycles also internally latch addresses and data needed for the programming and erase operations.
The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting
the data contents of other sectors. The device is fully
erased when shipped from the factory.
Device programming and erasure are initiated through
command sequences. Once a program or erase operation has begun, the host system need only poll the
DQ7 (Data# Polling) or DQ6 (toggle) status bits or
monitor the Ready/Busy# (RY/BY#) output to determine whether the operation is complete. To facilitate
programming, an Unlock Bypass mode reduces command sequence overhead by requiring only two write
cycles to program data instead of four.
The VersatileI/O™ (VIO) control allows the host system to set the voltage levels that the device generates
and tolerates on the CE# control input and DQ I/Os to
2
the same voltage level that is asserted on the VIO pin.
Refer to the Ordering Information section for valid VIO
options.
Hardware data protection measures include a low
VCC detector that automatically inhibits write operations during power transitions. The hardware sector
protection feature disables both program and erase
operations in any combination of sectors of memory.
This can be achieved in-system or via programming
equipment.
The Erase Suspend/Erase Resume feature allows
the host system to pause an erase operation in a given
sector to read or program any other sector and then
complete the erase operation. The Program Suspend/Program Resume feature enables the host system to pause a program operation in a given sector to
read any other sector and then complete the program
operation.
The hardware RESET# pin terminates any operation
in progress and resets the device, after which it is then
ready for a new operation. The RESET# pin may be
tied to the system reset circuitry. A system reset would
thus also reset the device, enabling the host system to
read boot-up firmware from the Flash memory device.
The device reduces power consumption in the
standby mode when it detects specific voltage levels
on CE# and RESET#, or when addresses have been
stable for a specified period of time.
The Write Protect (WP#) feature protects the first or
last sector by asserting a logic low on the WP#/ACC
pin. The protected sector will still be protected even
during accelerated programming.
The SecSi™ (Secured Silicon) Sector provides a
128-word/256-byte area for code or data that can be
permanently protected. Once this sector is protected,
no further changes within the sector can occur.
Spansion MirrorBit flash technology combines years of
Flash memory manufacturing experience to produce
the highest levels of quality, reliability and cost effectiveness. The device electrically erases all bits within a
sector simultaneously via hot-hole assisted erase. The
data is programmed using hot electron injection.
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
MIRRORBIT 64 MBIT DEVICE FAMILY
Device
Sector Architecture
Packages
VIO
RY/BY#
WP#, ACC
WP# Protection
x8
Uniform (64 Kbyte)
48-pin TSOP (std. & rev. pinout),
63-ball FBGA
Yes
Yes
ACC only
No WP#
LV640MT/B
x8/x16
Boot (8 x 8 Kbyte
at top & bottom)
48-pin TSOP, 63-ball Fine-pitch BGA,
64-ball Fortified BGA
No
Yes
WP#/ACC pin
2 x 8 Kbyte
top or bottom
LV640MH/L
x8/x16
Uniform (64 Kbyte)
56-pin TSOP (std. & rev. pinout),
64-ball Fortified BGA
Yes
Yes
WP#/ACC pin
1 x 64 Kbyte
high or low
LV641MH/L
x16
Uniform (32 Kword)
48-pin TSOP (std. & rev. pinout)
Yes
No
Separate WP#
and ACC pins
1 x 32 Kword
top or bottom
LV640MU
x16
Uniform (32 Kword)
64-ball Fortified BGA,
64-Ball Fine-Pitch BGA
Yes
Yes
ACC only
No WP#
LV065MU
Bus
Related Documents
To download related documents, click on the following
links or go to www.amd.com→Flash Memory→Product Information→MirrorBit→Flash Information→Technical Documentation.
MirrorBit™ Flash Memory Write Buffer Programming
and Page Buffer Read
December 14, 2005
Implementing a Common Layout for AMD MirrorBit
and Intel StrataFlash Memory Devices
Migrating from Single-byte to Three-byte Device IDs
AMD MirrorBit™ White Paper
Am29LV640MH/L
3
D A T A S H E E T
TABLE OF CONTENTS
Product Selector Guide . . . . . . . . . . . . . . . . . . . . . 5
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 9
Device Bus Operations . . . . . . . . . . . . . . . . . . . . . 10
Table 1. Device Bus Operations .....................................................10
Word/Byte Configuration ........................................................ 11
VersatileIO™ (VIO) Control ..................................................... 11
Requirements for Reading Array Data ................................... 11
Page Mode Read .................................................................... 11
Writing Commands/Command Sequences ............................ 11
Write Buffer ............................................................................. 11
Accelerated Program Operation ............................................. 11
Autoselect Functions .............................................................. 12
Standby Mode ........................................................................ 12
Automatic Sleep Mode ........................................................... 12
RESET#: Hardware Reset Pin ............................................... 12
Output Disable Mode .............................................................. 12
Autoselect Mode ..................................................................... 16
Table 2. Autoselect Codes, (High Voltage Method) .......................16
Sector Group Protection and Unprotection ............................. 16
Table 3. Sector Group Protection/Unprotection Address Table ......16
Write Protect (WP#) ................................................................ 18
Temporary Sector Group Unprotect ....................................... 18
Figure 1. Temporary Sector Group Unprotect Operation................ 18
Figure 2. In-System Sector Group
Protect/Unprotect Algorithms .......................................................... 19
SecSi (Secured Silicon) Sector Flash Memory Region .......... 20
Figure 3. SecSi Sector Protect Verify.............................................. 21
Hardware Data Protection ...................................................... 21
Low VCC Write Inhibit ............................................................ 21
Write Pulse “Glitch” Protection ............................................... 21
Logical Inhibit .......................................................................... 21
Power-Up Write Inhibit ............................................................ 21
Common Flash Memory Interface (CFI) . . . . . . . 21
CFI Query Identification String........................................................ 22
System Interface String................................................................... 22
Table 6. Device Geometry Definition .............................................. 23
Table 7. Primary Vendor-Specific Extended Query ........................ 24
Command Definitions . . . . . . . . . . . . . . . . . . . . . 24
Reading Array Data ................................................................ 24
Reset Command ..................................................................... 25
Autoselect Command Sequence ............................................ 25
Enter SecSi Sector/Exit SecSi Sector Command Sequence .. 25
Word/Byte Program Command Sequence ............................. 25
Unlock Bypass Command Sequence ..................................... 26
Write Buffer Programming ...................................................... 26
Accelerated Program .............................................................. 27
Figure 4. Write Buffer Programming Operation............................... 28
Figure 5. Program Operation .......................................................... 29
Program Suspend/Program Resume Command Sequence ... 29
Figure 6. Program Suspend/Program Resume............................... 30
Chip Erase Command Sequence ........................................... 30
Sector Erase Command Sequence ........................................ 30
Figure 7. Erase Operation............................................................... 31
4
Erase Suspend/Erase Resume Commands ........................... 32
Command Definitions ............................................................. 33
Command Definitions (x16 Mode, BYTE# = VIH) ............................ 33
Command Definitions (x8 Mode, BYTE# = VIL)............................... 34
Write Operation Status . . . . . . . . . . . . . . . . . . . . 35
DQ7: Data# Polling ................................................................. 35
Figure 8. Data# Polling Algorithm .................................................. 36
RY/BY#: Ready/Busy# ............................................................ 37
DQ6: Toggle Bit I .................................................................... 37
Figure 9. Toggle Bit Algorithm........................................................ 38
DQ2: Toggle Bit II ................................................................... 38
Reading Toggle Bits DQ6/DQ2 ............................................... 39
DQ5: Exceeded Timing Limits ................................................ 39
DQ3: Sector Erase Timer ....................................................... 39
DQ1: Write-to-Buffer Abort ..................................................... 39
Table 10. Write Operation Status ................................................... 40
Absolute Maximum Ratings . . . . . . . . . . . . . . . . 41
Figure 10. Maximum Negative Overshoot Waveform .................... 41
Figure 11. Maximum Positive
Overshoot Waveform ..................................................................... 41
Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . 41
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 42
Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 12. Test Setup..................................................................... 43
Table 1. Test Specifications ........................................................... 43
Key to Switching Waveforms. . . . . . . . . . . . . . . . 43
Figure 13. Input Waveforms and
Measurement Levels...................................................................... 43
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 44
Read-Only Operations ........................................................... 44
Figure 14. Read Operation Timings ............................................... 44
Figure 15. Page Read Timings ...................................................... 45
Hardware Reset (RESET#) .................................................... 46
Figure 16. Reset Timings ............................................................... 46
Erase and Program Operations .............................................. 47
Figure 17. Program Operation Timings..........................................
Figure 18. Accelerated Program Timing Diagram..........................
Figure 19. Chip/Sector Erase Operation Timings ..........................
Figure 20. Data# Polling Timings
(During Embedded Algorithms)......................................................
Figure 21. Toggle Bit Timings (During Embedded Algorithms)......
Figure 22. DQ2 vs. DQ6.................................................................
48
48
49
50
51
51
Temporary Sector Unprotect .................................................. 52
Figure 23. Temporary Sector Group Unprotect Timing Diagram ... 52
Figure 24. Sector Group Protect and Unprotect Timing Diagram .. 53
Alternate CE# Controlled Erase and Program Operations ..... 54
Figure 25. Alternate CE# Controlled Write (Erase/Program)
Operation Timings.......................................................................... 55
Erase And Programming Performance . . . . . . . 56
Latchup Characteristics . . . . . . . . . . . . . . . . . . . . 56
TSOP Pin and BGA Package Capacitance . . . . . 56
Data Retention. . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . 57
TS056/TSR056—56-Pin Standard and Reverse Pinout
Thin Small Outline Package (TSOP) ...................................... 57
LAA064—64-Ball Fortified Ball Grid Array (FBGA) 13 x 11 mm
Package .................................................................................. 58
Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 59
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
PRODUCT SELECTOR GUIDE
Part Number
90R
(VIO = 3.0–
3.6 V)
VCC = 3.0–3.6 V
Speed
Option
90
90
25
30
30
40
30
40
25
30
30
40
30
40
VCC = 2.7–3.6 V
Max. Access Time (ns)
Max. CE# Access Time (ns)
Max. Page access time
(tPACC)
Max. OE# Access Time (ns)
Am29LV640MH/L
112R
(VIO = 1.65–
3.6 V)
112
(VIO = 1.65
–3.6 V)
110
110
101R
(VIO = 2.7–
3.6 V)
101
(VIO = 2.7–
3.6 V)
100
100
120R
(VIO = 1.65
–3.6 V)
120
(VIO = 1.65–
3.6 V)
120
120
Notes:
1. See “AC Characteristics” for full specifications.
2. For the Am29LV640MH-L device, the last numeric digit in the
speed option (e.g. 101, 112, 120) is used for internal
purposes only. Please use OPNs as listed on p. 9 when
placing orders.
BLOCK DIAGRAM
DQ0–DQ15 (A-1)
RY/BY#
VCC
VSS
Sector Switches
VIO
Erase Voltage
Generator
Input/Output
Buffers
RESET#
WE#
WP#/ACC
BYTE#
State
Control
Command
Register
PGM Voltage
Generator
Chip Enable
Output Enable
Logic
CE#
OE#
VCC Detector
Timer
A21–A0
December 14, 2005 26191F3
Am29LV640MH/L
Address Latch
STB
STB
Data
Latch
Y-Decoder
Y-Gating
X-Decoder
Cell Matrix
5
D A T A S H E E T
CONNECTION DIAGRAMS
NC
NC
A15
A14
A13
A12
A11
A10
A9
A8
A19
A20
WE#
RESET#
A21
WP#/ACC
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
NC
NC
NC
NC
A16
BYTE#
VSS
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
NC
VIO
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
56-Pin Standard TSOP
56-Pin Reverse TSOP
Am29LV640MH/L
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
NC
NC
A16
BYTE#
VSS
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
NC
VIO
NC
NC
A15
A14
A13
A12
A11
A10
A9
A8
A19
A20
WE#
RESET#
A21
WP#/ACC
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
NC
NC
26191F3 December 14, 2005
D A T A S H E E T
CONNECTION DIAGRAMS
64-Ball Fortified BGA
Top View, Balls Facing Down
A8
B8
C8
D8
E8
F8
G8
H8
NC
NC
NC
VIO
VSS
NC
NC
NC
A7
B7
C7
D7
E7
F7
G7
H7
A13
A12
A14
A15
A16
A6
B6
C6
D6
E6
F6
VSS
G6
H6
A9
A8
A10
A11
DQ7
DQ14
DQ13
DQ6
A5
B5
C5
D5
E5
F5
G5
H5
WE#
RESET#
A21
A19
DQ5
DQ12
VCC
DQ4
A4
B4
C4
D4
E4
F4
G4
H4
A18
A20
DQ2
DQ10
DQ11
DQ3
RY/BY# WP#/ACC
A3
B3
C3
D3
E3
F3
G3
H3
A7
A17
A6
A5
DQ0
DQ8
DQ9
DQ1
A2
B2
C2
D2
E2
F2
G2
H2
A3
A4
A2
A1
A0
CE#
OE#
VSS
A1
B1
C1
D1
E1
F1
G1
H1
NC
NC
NC
NC
NC
VIO
NC
NC
Special Package Handling Instructions
Special handling is required for Flash Memory products in molded packages (TSOP and BGA). The pack-
December 14, 2005
BYTE# DQ15/A-1
age and/or data integrity may be compromised if the
package body is exposed to temperatures above 150°C
for prolonged periods of time.
Am29LV640MH/L
7
D A T A S H E E T
PIN DESCRIPTION
RESET#
= Hardware Reset Pin input
A21–A0
RY/BY#
= Ready/Busy output
DQ14–DQ0 = 15 Data inputs/outputs
BYTE#
= Selects 8-bit or 16-bit mode
DQ15/A-1
= DQ15 (Data input/output, word mode),
A-1 (LSB Address input, byte mode)
VCC
CE#
= Chip Enable input
= 3.0 volt-only single power supply
(see Product Selector Guide for
speed options and voltage
supply tolerances)
OE#
= Output Enable input
VIO
= Output Buffer power
WE#
= Write Enable input
VSS
= Device Ground
WP#/ACC
= Hardware Write Protect input/Programming Acceleration input
NC
= Pin Not Connected Internally
= 22 Address inputs
Logic Symbol
22
A21–A0
CE#
16 or 8
DQ15–DQ0
(A-1)
OE#
WE#
WP#/ACC
RESET#
VIO
RY/BY#
BYTE#
8
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
ORDERING INFORMATION
Standard Products
Standard products are available in several packages and operating ranges. The order
number (Valid Combination) is formed by a combination of the following:
Am29LV640M
H
120R
PC
I
TEMPERATURE RANGE
I
= Industrial (–40°C to +85°C)
PACKAGE TYPE
E
= 56-Pin Thin Small Outline Package (TSOP) Standard Pinout (TS 056)
F
= 56-Pin Thin Small Outline Package (TSOP) Reverse Pinout (TSR056)
PC
= 64-Ball Fortified Ball Grid Array,
1.0 mm pitch, 13 x 11 mm package (LAA064)
SPEED OPTION
See Product Selector Guide and Valid Combinations
SECTOR ARCHITECTURE AND WP# PROTECTION (WP# = VIL)
H
= Uniform sector device, highest address sector protected
L
= Uniform sector device, lowest address sector protected
DEVICE NUMBER/DESCRIPTION
Am29LV640MH/L
64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit™ Uniform Sector Flash Memory
with VersatileIO™ Control, 3.0 Volt-only Read, Program, and Erase
Valid Combinations for
TSOP Package (Note 2)
Speed
(ns)
VIO
Range (V)
VCC
Range (V)
Am29LV640MH90R
Am29LV640ML90R
90
3.0–3.6
3.0–3.6
Am29LV640MH112
Am29LV640ML112
110
1.65–3.6
Am29LV640MH120
Am29LV640ML120
120
Valid Combinations for
Fortified BGA Package (Note 2)
Package
Marking
Order Number
VIO
VCC
Speed
Range Range
(ns)
(V)
(V)
Am29LV640MH90R
Am29LV640ML90R
L640MH90NI
L640ML90NI
90
3.0–
3.6
1.65–3.6
Am29LV640MH101
Am29LV640ML101
L640MH01PI
L640ML01PI
100
2.7–
3.6
100
2.7–3.6
Am29LV640MH112
Am29LV640ML112
L640MH11PI
L640ML11PI
110
1.65–
3.6
Am29LV640MH112R
Am29LV640ML112R
110
1.65–3.6
L640MH12PI
L640ML12PI
120
1.65–
3.6
Am29LV640MH120R
Am29LV640ML120R
120
1.65–3.6
Am29LV640MH101R
Am29LV640ML101R
L640MH01NI
L640ML01NI
100
2.7–
3.
Am29LV640MH112R
Am29LV640ML112R
L640MH11NI
L640ML11NI
110
1.65–
3.6
Am29LV640MH120R
Am29LV640ML120R
L640MH12NI
L640ML12NI
120
1.65–
3.6
2.7–3.6
EI,
FI
Am29LV640MH101R
Am29LV640ML101R
3.0–3.6
Am29LV640MH120
Am29LV640ML120
PCI
3.0–
3.6
2.7–
3.6
3.0–
3.6
Valid Combinations
Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to
confirm availability of specific valid combinations and to check on newly released combinations.
Notes:
1. For the Am29LV640MH-L device, the last numeric digit in the speed
option (e.g. 101, 112, 120) is used for internal purposes only.
2. To select product with ESN factory-locked into the SecSi Sector:
1) select order number from the valid combinations given above,
2) add designator “N” at the end of the order number, and 3)
December 14, 2005
modify the speed option indicator as follows [101R = 10R, 112R =
11R, 120R = 12R, 90R, 101, 112, 120 = no change] Example:
Am29LV640MH12RPCIN. For Fortified BGA packages, the
designator “N” will also appear at the end of the package marking.
Example: L640MH12NIN.
Am29LV640MH/L
9
D A T A S H E E T
DEVICE BUS OPERATIONS
This section describes the requirements and use of
the device bus operations, which are initiated through
the internal command register. The command register
itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the address and data information
needed to execute the command. The contents of the
Table 1.
Operation
register serve as inputs to the internal state machine.
The state machine outputs dictate the function of the
device. Table 1 lists the device bus operations, the inputs and control levels they require, and the resulting
output. The following subsections describe each of
these operations in further detail.
Device Bus Operations
ACC
X
X
VHH
Addresses
(Note 2)
AIN
AIN
AIN
H
X
High-Z
High-Z
High-Z
X
X
X
X
SA, A6 =L,
A3=L, A2=L,
A1=H, A0=L
SA, A6=H,
A3=L, A2=L,
A1=H, A0=L
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
(Note 4)
X
X
(Note 4)
X
X
CE#
L
L
L
VCC ±
0.3 V
L
X
OE#
L
H
H
Sector Group Protect
(Note 2)
L
H
L
VID
H
X
Sector Group Unprotect
(Note 2)
L
H
L
VID
H
X
Temporary Sector
Group Unprotect
X
X
X
VID
H
X
Read
Write (Program/Erase)
Accelerated Program
Standby
Output Disable
Reset
X
H
X
WE# RESET#
WP#
H
H
X
L
H
(Note 3)
L
H
(Note 3)
VCC ±
X
X
0.3 V
H
H
X
X
L
X
DQ8–DQ15
DQ0–
BYTE#
BYTE#
DQ7
= VIL
= VIH
DOUT
DOUT
DQ8–DQ14
(Note 4) (Note 4)
= High-Z,
(Note 4) (Note 4) DQ15 = A-1
AIN
(Note 4) (Note 4)
High-Z
Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5–12.5 V, VHH = 11.5–12.5 V, X = Don’t Care, SA = Sector Address,
AIN = Address In, DIN = Data In, DOUT = Data Out
Notes:
1. Addresses are A21:A0 in word mode; A21:A-1 in byte
mode. Sector addresses are A21:A15 in both modes.
2. The sector protect and sector unprotect functions may also
be implemented via programming equipment. See the
“Sector Group Protection and Unprotection” section.
3. If WP# = VIL, the first or last sector remains protected. If
WP# = VIH, the first or last sector will be protected or
10
unprotected as determined by the method described in
“Sector Group Protection and Unprotection”. All sectors are
unprotected when shipped from the factory (The SecSi
Sector may be factory protected depending on version
ordered.)
4. DIN or DOUT as required by command sequence, data
polling, or sector protect algorithm (see Figure 2).
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
Word/Byte Configuration
The BYTE# pin controls whether the device data I/O
pins operate in the byte or word configuration. If the
BYTE# pin is set at logic ‘1’, the device is in word configuration, DQ0–DQ15 are active and controlled by
CE# and OE#.
If the BYTE# pin is set at logic ‘0’, the device is in byte
configuration, and only data I/O pins DQ0–DQ7 are
active and controlled by CE# and OE#. The data I/O
pins DQ8–DQ14 are tri-stated, and the DQ15 pin is
used as an input for the LSB (A-1) address function.
The random or initial page access is equal to tACC or
tCE and subsequent page read accesses (as long as
the locations specified by the microprocessor falls
within that page) is equivalent to tPACC. When CE# is
deasserted and reasserted for a subsequent access,
the access time is tACC or tCE. Fast page mode accesses are obtained by keeping the “read-page addresses” constant and changing the “intra-read page”
addresses.
Writing Commands/Command Sequences
VersatileIO™ (VIO) Control
The VersatileIO™ (VIO) control allows the host system
to set the voltage levels that the device generates and
tolerates on CE# and DQ I/Os to the same voltage
level that is asserted on VIO. See “Ordering Information” on page 9 for VIO options on this device.
For example, a VI/O of 1.65–3.6 volts allows for I/O at
the 1.8 or 3 volt levels, driving and receiving signals to
and from other 1.8 or 3 V devices on the same data
bus.
Requirements for Reading Array Data
To read array data from the outputs, the system must
drive the CE# and OE# pins to VIL. CE# is the power
control and selects the device. OE# is the output control and gates array data to the output pins. WE#
should remain at VIH.
The internal state machine is set for reading array data
upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory
content occurs during the power transition. No command is necessary in this mode to obtain array data.
Standard microprocessor read cycles that assert valid
addresses on the device address inputs produce valid
data on the device data outputs. The device remains
enabled for read access until the command register
contents are altered.
See “Reading Array Data” for more information. Refer
to the AC Read-Only Operations table for timing specifications and to Figure 14 for the timing diagram. Refer
to the DC Characteristics table for the active current
specification on reading array data.
Page Mode Read
The device is capable of fast page mode read and is
compatible with the page mode Mask ROM read operation. This mode provides faster read access speed
for random locations within a page. The page size of
the device is 4 words/8 bytes. The appropriate page is
selected by the higher address bits A(max)–A2. Address bits A1–A0 in word mode (A1–A-1 in byte mode)
determine the specific word within a page. This is an
December 14, 2005
asynchronous operation; the microprocessor supplies
the specific word location.
To write a command or command sequence (which includes programming data to the device and erasing
sectors of memory), the system must drive WE# and
CE# to VIL, and OE# to VIH.
The device features an Unlock Bypass mode to facilitate faster programming. Once the device enters the
Unlock Bypass mode, only two write cycles are required to program a word or byte, instead of four. The
“Word/Byte Program Command Sequence” section
has details on programming data to the device using
both standard and Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sectors, or the entire device. Table 2 indicates the address
space that each sector occupies.
Refer to the DC Characteristics table for the active
current specification for the write mode. The AC Characteristics section contains timing specification tables
and timing diagrams for write operations.
Write Buffer
Write Buffer Programming allows the system to write a
maximum of 16 words/32 bytes in one programming
operation. This results in faster effective programming
time than the standard programming algorithms. See
“Write Buffer” for more information.
Accelerated Program Operation
The device offers accelerated program operations
through the ACC function. This is one of two functions
provided by the WP#/ACC pin. This function is primarily intended to allow faster manufacturing throughput
at the factory.
If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass
mode, temporarily unprotects any protected sectors,
and uses the higher voltage on the pin to reduce the
time required for program operations. The system
would use a two-cycle program command sequence
as required by the Unlock Bypass mode. Removing
VHH from the WP#/ACC pin returns the device to normal operation. Note that the WP#/ACC pin must not be
Am29LV640MH/L
11
D A T A S H E E T
at VHH for operations other than accelerated programming, or device damage may result. In addition, no external pullup is necessary since the WP#/ACC pin has
internal pullup to VCC.
Autoselect Functions
If the system writes the autoselect command sequence, the device enters the autoselect mode. The
system can then read autoselect codes from the internal register (which is separate from the memory array)
on DQ7–DQ0. Standard read cycle timings apply in
this mode. Refer to the Autoselect Mode and Autoselect Command Sequence sections for more information.
Standby Mode
When the system is not reading or writing to the device, it can place the device in the standby mode. In
this mode, current consumption is greatly reduced,
and the outputs are placed in the high impedance
state, independent of the OE# input.
this mode when addresses remain stable for tACC +
30 ns. The automatic sleep mode is independent of
the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output
data is latched and always available to the system.
Refer to the DC Characteristics table for the automatic
sleep mode current specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of resetting the device to reading array data. When the RESET# pin is driven low for at least a period of tRP, the
device immediately terminates any operation in
progress, tristates all output pins, and ignores all
read/write commands for the duration of the RESET#
pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is
ready to accept another command sequence, to ensure data integrity.
The device enters the CMOS standby mode when the
CE# and RESET# pins are both held at VIO ± 0.3 V.
(Note that this is a more restricted voltage range than
VIH.) If CE# and RESET# are held at VIH, but not within
VIO ± 0.3 V, the device will be in the standby mode, but
the standby current will be greater. The device requires standard access time (t CE ) for read access
when the device is in either of these standby modes,
before it is ready to read data.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at VSS±0.3 V, the device
draws CMOS standby current (ICC4). If RESET# is held
at VIL but not within VSS±0.3 V, the standby current will
be greater.
If the device is deselected during erasure or programming, the device draws active current until the
operation is completed.
Refer to the AC Characteristics tables for RESET# parameters and to Figure 16 for the timing diagram.
Refer to the DC Characteristics table for the standby
current specification.
Output Disable Mode
Automatic Sleep Mode
The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firmware from the Flash memory.
When the OE# input is at VIH, output from the device is
disabled. The output pins are placed in the high
impedance state.
The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables
12
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
Sector
A21–A15
Sector Size
(Kbytes/Kwords)
8-bit
Address Range
(in hexadecimal)
16-bit
Address Range
(in hexadecimal)
SA0
0
0
0
0
0
0
0
64/32
000000–00FFFF
000000–007FFF
SA1
0
0
0
0
0
0
1
64/32
010000–01FFFF
008000–00FFFF
SA2
0
0
0
0
0
1
0
64/32
020000–02FFFF
010000–017FFF
SA3
0
0
0
0
0
1
1
64/32
030000–03FFFF
018000–01FFFF
SA4
0
0
0
0
1
0
0
64/32
040000–04FFFF
020000–027FFF
SA5
0
0
0
0
1
0
1
64/32
050000–05FFFF
028000–02FFFF
SA6
0
0
0
0
1
1
0
64/32
060000–06FFFF
030000–037FFF
SA7
0
0
0
0
1
1
1
64/32
070000–07FFFF
038000–03FFFF
SA8
0
0
0
1
0
0
0
64/32
080000–08FFFF
040000–047FFF
SA9
0
0
0
1
0
0
1
64/32
090000–09FFFF
048000–04FFFF
SA10
0
0
0
1
0
1
0
64/32
0A0000–0AFFFF
050000–057FFF
SA11
0
0
0
1
0
1
1
64/32
0B0000–0BFFFF
058000–05FFFF
SA12
0
0
0
1
1
0
0
64/32
0C0000–0CFFFF
060000–067FFF
SA13
0
0
0
1
1
0
1
64/32
0D0000–0DFFFF
068000–06FFFF
SA14
0
0
0
1
1
1
0
64/32
0E0000–0EFFFF
070000–077FFF
SA15
0
0
0
1
1
1
1
64/32
0F0000–0FFFFF
078000–07FFFF
SA16
0
0
1
0
0
0
0
64/32
100000–10FFFF
080000–087FFF
SA17
0
0
1
0
0
0
1
64/32
110000–11FFFF
088000–08FFFF
SA18
0
0
1
0
0
1
0
64/32
120000–12FFFF
090000–097FFF
SA19
0
0
1
0
0
1
1
64/32
130000–13FFFF
098000–09FFFF
SA20
0
0
1
0
1
0
0
64/32
140000–14FFFF
0A0000–0A7FFF
SA21
0
0
1
0
1
0
1
64/32
150000–15FFFF
0A8000–0AFFFF
SA22
0
0
1
0
1
1
0
64/32
160000–16FFFF
0B0000–0B7FFF
SA23
0
0
1
0
1
1
1
64/32
170000–17FFFF
0B8000–0BFFFF
SA24
0
0
1
1
0
0
0
64/32
180000–18FFFF
0C0000–0C7FFF
SA25
0
0
1
1
0
0
1
64/32
190000–19FFFF
0C8000–0CFFFF
SA26
0
0
1
1
0
1
0
64/32
1A0000–1AFFFF
0D0000–0D7FFF
SA27
0
0
1
1
0
1
1
64/32
1B0000–1BFFFF
0D8000–0DFFFF
SA28
0
0
1
1
1
0
0
64/32
1C0000–1CFFFF
0E0000–0E7FFF
SA29
0
0
1
1
1
0
1
64/32
1D0000–1DFFFF
0E8000–0EFFFF
SA30
0
0
1
1
1
1
0
64/32
1E0000–1EFFFF
0F0000–0F7FFF
SA31
0
0
1
1
1
1
1
64/32
1F0000–1FFFFF
0F8000–0FFFFF
SA32
0
1
0
0
0
0
0
64/32
200000–20FFFF
100000–107FFF
SA33
0
1
0
0
0
0
1
64/32
210000–21FFFF
108000–10FFFF
SA34
0
1
0
0
0
1
0
64/32
220000–22FFFF
110000–117FFF
SA35
0
1
0
0
0
1
1
64/32
230000–23FFFF
118000–11FFFF
SA36
0
1
0
0
1
0
0
64/32
240000–24FFFF
120000–127FFF
SA37
0
1
0
0
1
0
1
64/32
250000–25FFFF
128000–12FFFF
SA38
0
1
0
0
1
1
0
64/32
260000–26FFFF
130000–137FFF
SA39
0
1
0
0
1
1
1
64/32
270000–27FFFF
138000–13FFFF
SA40
0
1
0
1
0
0
0
64/32
280000–28FFFF
140000–147FFF
SA41
0
1
0
1
0
0
1
64/32
290000–29FFFF
148000–14FFFF
SA42
0
1
0
1
0
1
0
64/32
2A0000–2AFFFF
150000–157FFF
SA43
0
1
0
1
0
1
1
64/32
2B0000–2BFFFF
158000–15FFFF
SA44
0
1
0
1
1
0
0
64/32
2C0000–2CFFFF
160000–167FFF
SA45
0
1
0
1
1
0
1
64/32
2D0000–2DFFFF
168000–16FFFF
SA46
0
1
0
1
1
1
0
64/32
2E0000–2EFFFF
170000–177FFF
SA47
0
1
0
1
1
1
1
64/32
2F0000–2FFFFF
178000–17FFFF
SA48
0
1
1
0
0
0
0
64/32
300000–30FFFF
180000–187FFF
SA49
0
1
1
0
0
0
1
64/32
310000–31FFFF
188000–18FFFF
SA50
0
1
1
0
0
1
0
64/32
320000–32FFFF
190000–197FFF
SA51
0
1
1
0
0
1
1
64/32
330000–33FFFF
198000–19FFFF
SA52
0
1
1
0
1
0
0
64/32
340000–34FFFF
1A0000–1A7FFF
SA53
0
1
1
0
1
0
1
64/32
350000–35FFFF
1A8000–1AFFFF
SA54
0
1
1
0
1
1
0
64/32
360000–36FFFF
1B0000–1B7FFF
SA55
0
1
1
0
1
1
1
64/32
370000–37FFFF
1B8000–1BFFFF
December 14, 2005
Am29LV640MH/L
13
D A T A S H E E T
Sector
14
A21–A15
Sector Size
(Kbytes/Kwords)
8-bit
Address Range
(in hexadecimal)
16-bit
Address Range
(in hexadecimal)
SA56
0
1
1
1
0
0
0
64/32
380000–38FFFF
1C0000–1C7FFF
SA57
0
1
1
1
0
0
1
64/32
390000–39FFFF
1C8000–1CFFFF
SA58
0
1
1
1
0
1
0
64/32
3A0000–3AFFFF
1D0000–1D7FFF
SA59
0
1
1
1
0
1
1
64/32
3B0000–3BFFFF
1D8000–1DFFFF
SA60
0
1
1
1
1
0
0
64/32
3C0000–3CFFFF
1E0000–1E7FFF
SA61
0
1
1
1
1
0
1
64/32
3D0000–3DFFFF
1E8000–1EFFFF
SA62
0
1
1
1
1
1
0
64/32
3E0000–3EFFFF
1F0000–1F7FFF
SA63
0
1
1
1
1
1
1
64/32
3F0000–3FFFFF
1F8000–1FFFFF
SA64
1
0
0
0
0
0
0
64/32
400000–40FFFF
200000–207FFF
SA65
1
0
0
0
0
0
1
64/32
410000–41FFFF
208000–20FFFF
SA66
1
0
0
0
0
1
0
64/32
420000–42FFFF
210000–217FFF
SA67
1
0
0
0
0
1
1
64/32
430000–43FFFF
218000–21FFFF
SA68
1
0
0
0
1
0
0
64/32
440000–44FFFF
220000–227FFF
SA69
1
0
0
0
1
0
1
64/32
450000–45FFFF
228000–22FFFF
SA70
1
0
0
0
1
1
0
64/32
460000–46FFFF
230000–237FFF
SA71
1
0
0
0
1
1
1
64/32
470000–47FFFF
238000–23FFFF
SA72
1
0
0
1
0
0
0
64/32
480000–48FFFF
240000–247FFF
SA73
1
0
0
1
0
0
1
64/32
490000–49FFFF
248000–24FFFF
SA74
1
0
0
1
0
1
0
64/32
4A0000–4AFFFF
250000–257FFF
SA75
1
0
0
1
0
1
1
64/32
4B0000–4BFFFF
258000–25FFFF
SA76
1
0
0
1
1
0
0
64/32
4C0000–4CFFFF
260000–267FFF
SA77
1
0
0
1
1
0
1
64/32
4D0000–4DFFFF
268000–26FFFF
SA78
1
0
0
1
1
1
0
64/32
4E0000–4EFFFF
270000–277FFF
SA79
1
0
0
1
1
1
1
64/32
4F0000–4FFFFF
278000–27FFFF
SA80
1
0
1
0
0
0
0
64/32
500000–50FFFF
280000–287FFF
SA81
1
0
1
0
0
0
1
64/32
510000–51FFFF
288000–28FFFF
SA82
1
0
1
0
0
1
0
64/32
520000–52FFFF
290000–297FFF
SA83
1
0
1
0
0
1
1
64/32
530000–53FFFF
298000–29FFFF
SA84
1
0
1
0
1
0
0
64/32
540000–54FFFF
2A0000–2A7FFF
SA85
1
0
1
0
1
0
1
64/32
550000–55FFFF
2A8000–2AFFFF
SA86
1
0
1
0
1
1
0
64/32
560000–56FFFF
2B0000–2B7FFF
SA87
1
0
1
0
1
1
1
64/32
570000–57FFFF
2B8000–2BFFFF
SA88
1
0
1
1
0
0
0
64/32
580000–58FFFF
2C0000–2C7FFF
SA89
1
0
1
1
0
0
1
64/32
590000–59FFFF
2C8000–2CFFFF
SA90
1
0
1
1
0
1
0
64/32
5A0000–5AFFFF
2D0000–2D7FFF
SA91
1
0
1
1
0
1
1
64/32
5B0000–5BFFFF
2D8000–2DFFFF
SA92
1
0
1
1
1
0
0
64/32
5C0000–5CFFFF
2E0000–2E7FFF
SA93
1
0
1
1
1
0
1
64/32
5D0000–5DFFFF
2E8000–2EFFFF
SA94
1
0
1
1
1
1
0
64/32
5E0000–5EFFFF
2F0000–2F7FFF
SA95
1
0
1
1
1
1
1
64/32
5F0000–5FFFFF
2F8000–2FFFFF
SA96
1
1
0
0
0
0
0
64/32
600000–60FFFF
300000–307FFF
SA97
1
1
0
0
0
0
1
64/32
610000–61FFFF
308000–30FFFF
SA98
1
1
0
0
0
1
0
64/32
620000–62FFFF
310000–317FFF
SA99
1
1
0
0
0
1
1
64/32
630000–63FFFF
318000–31FFFF
SA100
1
1
0
0
1
0
0
64/32
640000–64FFFF
320000–327FFF
SA101
1
1
0
0
1
0
1
64/32
650000–65FFFF
328000–32FFFF
SA102
1
1
0
0
1
1
0
64/32
660000–66FFFF
330000–337FFF
SA103
1
1
0
0
1
1
1
64/32
670000–67FFFF
338000–33FFFF
SA104
1
1
0
1
0
0
0
64/32
680000–68FFFF
340000–347FFF
SA105
1
1
0
1
0
0
1
64/32
690000–69FFFF
348000–34FFFF
SA106
1
1
0
1
0
1
0
64/32
6A0000–6AFFFF
350000–357FFF
SA107
1
1
0
1
0
1
1
64/32
6B0000–6BFFFF
358000–35FFFF
SA108
1
1
0
1
1
0
0
64/32
6C0000–6CFFFF
360000–367FFF
SA109
1
1
0
1
1
0
1
64/32
6D0000–6DFFFF
368000–36FFFF
SA110
1
1
0
1
1
1
0
64/32
6E0000–6EFFFF
370000–377FFF
SA111
1
1
0
1
1
1
1
64/32
6F0000–6FFFFF
378000–37FFFF
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
Sector
A21–A15
Sector Size
(Kbytes/Kwords)
8-bit
Address Range
(in hexadecimal)
16-bit
Address Range
(in hexadecimal)
SA112
1
1
1
0
0
0
0
64/32
700000–70FFFF
380000–387FFF
SA113
1
1
1
0
0
0
1
64/32
710000–71FFFF
388000–38FFFF
SA114
1
1
1
0
0
1
0
64/32
720000–72FFFF
390000–397FFF
SA115
1
1
1
0
0
1
1
64/32
730000–73FFFF
398000–39FFFF
SA116
1
1
1
0
1
0
0
64/32
740000–74FFFF
3A0000–3A7FFF
SA117
1
1
1
0
1
0
1
64/32
750000–75FFFF
3A8000–3AFFFF
SA118
1
1
1
0
1
1
0
64/32
760000–76FFFF
3B0000–3B7FFF
SA119
1
1
1
0
1
1
1
64/32
770000–77FFFF
3B8000–3BFFFF
SA120
1
1
1
1
0
0
0
64/32
780000–78FFFF
3C0000–3C7FFF
SA121
1
1
1
1
0
0
1
64/32
790000–79FFFF
3C8000–3CFFFF
SA122
1
1
1
1
0
1
0
64/32
7A0000–7AFFFF
3D0000–3D7FFF
SA123
1
1
1
1
0
1
1
64/32
7B0000–7BFFFF
3D8000–3DFFFF
SA124
1
1
1
1
1
0
0
64/32
7C0000–7CFFFF
3E0000–3E7FFF
SA125
1
1
1
1
1
0
1
64/32
7D0000–7DFFFF
3E8000–3EFFFF
SA126
1
1
1
1
1
1
0
64/32
7E0000–7EFFFF
3F0000–3F7FFF
SA127
1
1
1
1
1
1
1
64/32
7F0000–7FFFFF
3F8000–3FFFFF
Note: The address range is A21:A-1 in byte mode (BYTE# = VIL) or A21:A0 in word mode (BYTE# = VIH).
December 14, 2005
Am29LV640MH/L
15
D A T A S H E E T
Autoselect Mode
In addition, when verifying sector protection, the sector
address must appear on the appropriate highest order
address bits (see Table 2). Table 3 shows the remaining address bits that are don’t care. When all necessary bits have been set as required, the programming
equipment may then read the corresponding identifier
code on DQ7–DQ0.
The autoselect mode provides manufacturer and device identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming
algorithm. However, the autoselect codes can also be
accessed in-system through the command register.
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in Tables 10 and 11. This
method does not require VID. Refer to the Autoselect
Command Sequence section for more information.
When using programming equipment, the autoselect
mode requires VID on address pin A9. Address pins
A6, A3, A2, A1, and A0 must be as shown in Table 3.
Table 2.
Description
Device ID
Manufacturer ID: AMD
CE#
L
Autoselect Codes, (High Voltage Method)
A21 A14
OE# WE# to
to
A15 A10
L
H
X
X
A9
A8
to
A7
A6
A5
to
A4
VID
X
L
X
Cycle 1
Cycle 2
L
L
H
X
X
VID
X
L
X
Cycle 3
A3
to
A2
DQ8 to DQ15
A1
A0
BYTE#= BYTE# =
VIH
VIL
DQ7 to DQ0
L
L
L
00
X
01h
L
L
H
22
X
7Eh
H
H
L
22
X
0Ch
H
H
H
22
X
01h
Sector Protection
Verification
L
L
H
SA
X
VID
X
L
X
L
H
L
X
X
01h (protected),
00h (unprotected)
SecSi Sector Indicator
Bit (DQ7), WP# protects
highest address sector
L
L
H
X
X
VID
X
L
X
L
H
H
X
X
98h (factory locked),
18h (not factory locked)
SecSi Sector Indicator
Bit (DQ7), WP# protects
lowest address sector
L
L
H
X
X
VID
X
L
X
L
H
H
X
X
88h (factory locked),
08h (not factory locked)
Legend: L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care.
Sector Group Protection and
Unprotection
The hardware sector group protection feature disables
both program and erase operations in any sector
group. In this device, a sector group consists of four
adjacent sectors that are protected or unprotected at
the same time (see Table 4). The hardware sector
group unprotection feature re-enables both program
and erase operations in previously protected sector
groups. Sector group protection/unprotection can be
implemented via two methods.
Sector protection/unprotection requires VID on the RESET# pin only, and can be implemented either in-system or via programming equipment. Figure 2 shows
Table 3.
16
the algorithms and Figure 24 shows the timing diagram. This method uses standard microprocessor bus
cycle timing. For sector group unprotect, all unprotected sector groups must first be protected prior to
the first sector group unprotect write cycle.
The device is shipped with all sector groups unprotected. AMD offers the option of programming and protecting sector groups at its factory prior to shipping the
device through AMD’s ExpressFlash™ Service. Contact an AMD representative for details.
It is possible to determine whether a sector group is
protected or unprotected. See the Autoselect Mode
section for details.
Sector Group Protection/Unprotection Address Table
Sector Group
A21–A15
SA0
0000000
SA1
0000001
SA2
0000010
SA3
0000011
SA4–SA7
00001xx
SA8–SA11
00010xx
SA12–SA15
00011xx
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
Table 3.
December 14, 2005
Sector Group Protection/Unprotection Address Table
Sector Group
A21–A15
SA16–SA19
00100xx
SA20–SA23
00101xx
SA24–SA27
00110xx
SA28–SA31
00111xx
SA32–SA35
01000xx
SA36–SA39
01001xx
SA40–SA43
01010xx
SA44–SA47
01011xx
SA48–SA51
01100xx
SA52–SA55
01101xx
SA56–SA59
01110xx
SA60–SA63
01111xx
SA64–SA67
10000xx
SA68–SA71
10001xx
SA72–SA75
10010xx
SA76–SA79
10011xx
SA80–SA83
10100xx
SA84–SA87
10101xx
SA88–SA91
10110xx
SA92–SA95
10111xx
SA96–SA99
11000xx
SA100–SA103
11001xx
SA104–SA107
11010xx
SA108–SA111
11011xx
SA112–SA115
11100xx
SA116–SA119
11101xx
SA120–SA123
11110xx
SA124
1111100
SA125
1111101
SA126
1111110
SA127
1111111
Am29LV640MH/L
17
D A T A S H E E T
Write Protect (WP#)
The Write Protect function provides a hardware
method of protecting the first or last sector without
using VID. Write Protect is one of two functions provided by the WP#/ACC input.
If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the first
or last sector independently of whether those sectors
were protected or unprotected using the method described in “Sector Group Protection and Unprotection”.
Note that if WP#/ACC is at VIL when the device is in
the standby mode, the maximum input load current is
increased. See the table in “DC Characteristics”.
If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the first or last sector was previously set to be protected or unprotected using the
method described in “Sector Group Protection and
Unprotection”. Note: No external pullup is necessary
since the WP#/ACC pin has internal pullup to VCC.
Temporary Sector Group Unprotect
(Note: In this device, a sector group consists of four adjacent sectors that are protected or unprotected at the
same time (see Table 4).
This feature allows temporary unprotection of previously protected sector groups to change data in-system. The Sector Group Unprotect mode is activated by
setting the RESET# pin to VID. During this mode, formerly protected sector groups can be programmed or
erased by selecting the sector group addresses. Once
VID is removed from the RESET# pin, all the previously
protected sector groups are protected again. Figure 1
shows the algorithm, and Figure 23 shows the timing
diagrams, for this feature.
START
RESET# = VID
(Note 1)
Perform Erase or
Program Operations
RESET# = VIH
Temporary Sector
Group Unprotect
Completed (Note 2)
Notes:
1. All protected sector groups unprotected (If WP# = VIL, the first or last sector will remain protected).
2. All previously protected sector groups are protected once again.
Figure 1.
18
Temporary Sector Group Unprotect Operation
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
START
START
PLSCNT = 1
RESET# = VID
Wait 1 μs
Temporary Sector
Group Unprotect
Mode
No
PLSCNT = 1
Protect all sector
groups: The indicated
portion of the sector
group protect algorithm
must be performed for all
unprotected sector
groups prior to issuing
the first sector group
unprotect address
RESET# = VID
Wait 1 μs
First Write
Cycle = 60h?
First Write
Cycle = 60h?
Temporary Sector
Group Unprotect
Mode
Yes
Yes
Set up sector
group address
No
All sector
groups
protected?
Yes
Sector Group Protect:
Write 60h to sector
group address with
A6–A0 = 0xx0010
Set up first sector
group address
Sector Group
Unprotect:
Write 60h to sector
group address with
A6–A0 = 1xx0010
Wait 150 µs
Verify Sector Group
Protect: Write 40h
to sector group
address with
A6–A0 = 0xx0010
Increment
PLSCNT
No
Reset
PLSCNT = 1
Read from
sector group address
with A6–A0
= 0xx0010
Wait 15 ms
Verify Sector Group
Unprotect: Write
40h to sector group
address with
A6–A0 = 1xx0010
Increment
PLSCNT
No
No
PLSCNT
= 25?
Read from
sector group
address with
A6–A0 = 1xx0010
Data = 01h?
Yes
No
Yes
Device failed
Protect
another
sector group?
Yes
PLSCNT
= 1000?
No
Yes
Remove VID
from RESET#
Device failed
Write reset
command
Sector Group
Protect
Algorithm
Sector Group
Protect complete
Set up
next sector group
address
No
Data = 00h?
Yes
Last sector
group
verified?
No
Yes
Sector Group
Unprotect
Algorithm
Remove VID
from RESET#
Write reset
command
Sector Group
Unprotect complete
Figure 2. In-System Sector Group
Protect/Unprotect Algorithms
December 14, 2005
Am29LV640MH/L
19
D A T A S H E E T
SecSi (Secured Silicon) Sector Flash
Memory Region
The SecSi (Secured Silicon) Sector feature provides a
Flash memory region that enables permanent part
identification through an Electronic Serial Number
(ESN). The SecSi Sector is 128 words/256 bytes in
length, and uses a SecSi Sector Indicator Bit (DQ7) to
indicate whether or not the SecSi Sector is locked
when shipped from the factory. This bit is permanently
set at the factory and cannot be changed, which prevents cloning of a factory locked part. This ensures the
security of the ESN once the product is shipped to the
field.
SecSi Sector Address Range
The SecSi sector address space in this device is allocated as follows:
Standard Factory
Locked
ExpressFlash
Factory Locked
000000h–
00000Fh
ESN
ESN or determined
by customer
000010h–
0000FFh
Unavailable
Determined
by customer
x16
x8
000000h–
000007h
000008h–
00007Fh
The system accesses the SecSi Sector through a
command sequence (see “Enter SecSi Sector/Exit
SecSi Sector Command Sequence”). After the system
has written the Enter SecSi Sector command sequence, it may read the SecSi Sector by using the addresses normally occupied by the first sector (SA0).
This mode of operation continues until the system issues the Exit SecSi Sector command sequence, or
until power is removed from the device. On power-up,
or following a hardware reset, the device reverts to
sending commands to sector SA0.
Factory Locked: SecSi Sector Programmed and
Protected At the Factory
In devices with an ESN, the SecSi Sector is protected
when the device is shipped from the factory. The SecSi
Sector cannot be modified in any way. See Table 5 for
SecSi Sector addressing.
Customers may opt to have their code programmed by
AMD through the AMD ExpressFlash service. The devices are then shipped from AMD’s factory with the
SecSi Sector permanently locked. Contact an AMD
representative for details on using AMD’s ExpressFlash service.
Customer Lockable: SecSi Sector NOT
Programmed or Protected At the Factory
As an alternative to the factory-locked version, the device may be ordered such that the customer may pro-
20
AMD offers the device with the SecSi Sector either
factor y locked o r custo mer lockable. The factory-locked version is always protected when shipped
from the factory, and has the SecSi (Secured Silicon)
Sector Indicator Bit permanently set to a “1.” The customer-lockable version is shipped with the SecSi Sector unprotected, allowing customers to program the
sector after receiving the device. The customer-lockable version also has the SecSi Sector Indicator Bit
permanently set to a “0.” Thus, the SecSi Sector Indicator Bit prevents customer-lockable devices from
being used to replace devices that are factory locked.
Customer Lockable
Determined by customer
gram and protect the 128-word/256 bytes SecSi
sector. See Table 5 for SecSi Sector addressing.
The system may program the SecSi Sector using the
write-buffer, accelerated and/or unlock bypass methods, in addition to the standard programming command sequence. See Command Definitions.
Programming and protecting the SecSi Sector must be
used with caution since, once protected, there is no
procedure available for unprotecting the SecSi Sector
area and none of the bits in the SecSi Sector memory
space can be modified in any way.
The SecSi Sector area can be protected using one of
the following procedures:
■ Write the three-cycle Enter SecSi Sector Region
command sequence, and then follow the in-system
sector protect algorithm as shown in Figure 2, except that RESET# may be at either VIH or VID. This
allows in-system protection of the SecSi Sector
without raising any device pin to a high voltage.
Note that this method is only applicable to the SecSi
Sector.
■ To verify the protect/unprotect status of the SecSi
Sector, follow the algorithm shown in Figure 3.
Once the SecSi Sector is programmed, locked and
verified, the system must write the Exit SecSi Sector
Region command sequence to return to reading and
writing within the remainder of the array.
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
START
RESET# =
VIH or VID
Wait 1 ms
Write 60h to
any address
Write 40h to SecSi
Sector address
with A6 = 0,
A1 = 1, A0 = 0
Read from SecSi
Sector address
with A6 = 0,
A1 = 1, A0 = 0
Figure 3.
If data = 00h,
SecSi Sector is
unprotected.
If data = 01h,
SecSi Sector is
protected.
Remove VIH or VID
from RESET#
Write reset
command
SecSi Sector
Protect Verify
complete
SecSi Sector Protect Verify
Hardware Data Protection
The command sequence requirement of unlock cycles
for programming or erasing provides data protection
against inadvertent writes (refer to Tables 10 and 11
for command definitions). In addition, the following
hardware data protection measures prevent accidental
erasure or programming, which might otherwise be
caused by spurious system level signals during VCC
power-up and power-down transitions, or from system
noise.
Low VCC Write Inhibit
When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC
power-up and power-down. The command register
and all internal program/erase circuits are disabled,
and the device resets to the read mode. Subsequent
writes are ignored until VCC is greater than VLKO. The
system must provide the proper signals to the control
pins to prevent unintentional writes when V CC is
greater than VLKO.
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on OE#, CE#
or WE# do not initiate a write cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE# =
VIL, CE# = VIH or WE# = VIH. To initiate a write cycle,
CE# and WE# must be a logical zero while OE# is a
logical one.
Power-Up Write Inhibit
If WE# = CE# = VIL and OE# = VIH during power up,
the device does not accept commands on the rising
edge of WE#. The internal state machine is automatically reset to the read mode on power-up.
COMMON FLASH MEMORY INTERFACE (CFI)
The Common Flash Interface (CFI) specification outlines device and host system software interrogation
handshake, which allows specific vendor-specified
software algorithms to be used for entire families of
devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and
backward-compatible for the specified flash device
families. Flash vendors can standardize their existing
interfaces for long-term compatibility.
This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address
December 14, 2005
55h, any time the device is ready to read array data.
The system can read CFI information at the addresses
given in Tables 6–9. To terminate reading CFI data,
the system must write the reset command.
The system can also write the CFI query command
when the device is in the autoselect mode. The device
enters the CFI query mode, and the system can read
CFI data at the addresses given in Tables 6–9. The
system must write the reset command to return the
device to reading array data.
Am29LV640MH/L
21
D A T A S H E E T
For further information, please refer to the CFI Specification and CFI Publication 100, available via the World
Wide Web at http://www.amd.com/flash/cfi. AlternaTable 4.
Addresses
(x16)
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
Addresses
(x8)
20h
22h
24h
26h
28h
2Ah
2Ch
2Eh
30h
32h
34h
Data
0051h
0052h
0059h
0002h
0000h
0040h
0000h
0000h
0000h
0000h
0000h
CFI Query Identification String
Description
Query Unique ASCII string “QRY”
Primary OEM Command Set
Address for Primary Extended Table
Alternate OEM Command Set (00h = none exists)
Address for Alternate OEM Extended Table (00h = none exists)
Table 5.
Addresses
(x16)
Addresses
(x8)
Data
1Bh
36h
0027h
1Ch
38h
0036h
1Dh
1Eh
1Fh
20h
21h
22h
23h
24h
25h
26h
3Ah
3Ch
3Eh
40h
42h
44h
46h
48h
4Ah
4Ch
0000h
0000h
0007h
0007h
000Ah
0000h
0001h
0005h
0004h
0000h
22
tively, contact a sales office or representative for copies of these documents.
System Interface String
Description
VCC Min. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
VCC Max. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
VPP Min. voltage (00h = no VPP pin present)
VPP Max. voltage (00h = no VPP pin present)
Typical timeout per single byte/word write 2N µs
Typical timeout for Min. size buffer write 2N µs (00h = not supported)
Typical timeout per individual block erase 2N ms
Typical timeout for full chip erase 2N ms (00h = not supported)
Max. timeout for byte/word write 2N times typical
Max. timeout for buffer write 2N times typical
Max. timeout per individual block erase 2N times typical
Max. timeout for full chip erase 2N times typical (00h = not supported)
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
Table 6.
Addresses
(x16)
27h
28h
29h
2Ah
2Bh
Addresses
(x8)
4Eh
50h
52h
54h
56h
Data
0017h
0002h
0000h
0005h
0000h
2Ch
58h
0001h
2Dh
2Eh
2Fh
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
3Ah
3Bh
3Ch
5Ah
5Ch
5Eh
60h
62h
64h
66h
68h
6Ah
6Ch
6Eh
70h
72h
74h
76h
78h
007Fh
0000h
0000h
0001h
0000h
0000h
0000h
0000h
0000h
0000h
0000h
0000h
0000h
0000h
0000h
0000h
December 14, 2005
Device Geometry Definition
Description
Device Size = 2N byte
Flash Device Interface description (refer to CFI publication 100)
Max. number of byte in multi-byte write = 2N
(00h = not supported)
Number of Erase Block Regions within device (01h = uniform device, 02h = boot
device)
Erase Block Region 1 Information
(refer to the CFI specification or CFI publication 100)
Erase Block Region 2 Information (refer to CFI publication 100)
Erase Block Region 3 Information (refer to CFI publication 100)
Erase Block Region 4 Information (refer to CFI publication 100)
Am29LV640MH/L
23
D A T A S H E E T
Table 7.
Addresses
(x16)
40h
41h
42h
43h
44h
Addresses
(x8)
80h
82h
84h
86h
88h
Data
0050h
0052h
0049h
0031h
0033h
45h
8Ah
0008h
46h
8Ch
0002h
47h
8Eh
0001h
48h
90h
0001h
49h
92h
0004h
4Ah
94h
0000h
4Bh
96h
0000h
4Ch
98h
0001h
4Dh
9Ah
00B5h
4Eh
9Ch
00C5h
4Fh
9Eh
0004h/
0005h
50h
A0h
0001h
Primary Vendor-Specific Extended Query
Description
Query-unique ASCII string “PRI”
Major version number, ASCII
Minor version number, ASCII
Address Sensitive Unlock (Bits 1-0)
0 = Required, 1 = Not Required
Process Technology (Bits 7-2) 0010b = 0.23 µm MirrorBit
Erase Suspend
0 = Not Supported, 1 = To Read Only, 2 = To Read & Write
Sector Protect
0 = Not Supported, X = Number of sectors in per group
Sector Temporary Unprotect
00 = Not Supported, 01 = Supported
Sector Protect/Unprotect scheme
04 = 29LV800 mode
Simultaneous Operation
00 = Not Supported, X = Number of Sectors in Bank
Burst Mode Type
00 = Not Supported, 01 = Supported
Page Mode Type
00 = Not Supported, 01 = 4 Word/8 Byte Page, 02 = 8 Word/16 Byte Page
ACC (Acceleration) Supply Minimum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
ACC (Acceleration) Supply Maximum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
Top/Bottom Boot Sector Flag
00h = Uniform Device without WP# protect, 02h = Bottom Boot Device, 03h = Top
Boot Device, 04h = Uniform sectors bottom WP# protect, 05h = Uniform sectors top
WP# protect
Program Suspend
00h = Not Supported, 01h = Supported
COMMAND DEFINITIONS
Writing specific address and data commands or sequences into the command register initiates device operations. Tables 10 and 11 define the valid register
command sequences. Writing incorrect address and
data values or writing them in the improper sequence may place the device in an unknown state. A
reset command is then required to return the device to
reading array data.
All addresses are latched on the falling edge of WE#
or CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens
first. Refer to the AC Characteristics section for timing
diagrams.
Reading Array Data
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is ready to read array data
24
after completing an Embedded Program or Embedded
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the erase-suspend-read mode, after
which the system can read data from any
non-erase-suspended sector. After completing a programming operation in the Erase Suspend mode, the
system may once again read array data with the same
exception. See the Erase Suspend/Erase Resume
Commands section for more information.
The system must issue the reset command to return
the device to the read (or erase-suspend-read) mode if
DQ5 goes high during an active program or erase operation, or if the device is in the autoselect mode. See
the next section, Reset Command, for more information.
See also Requirements for Reading Array Data in the
Device Bus Operations section for more information.
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
The Read-Only Operations table provides the read parameters, and Figure 14 shows the timing diagram.
Reset Command
Writing the reset command resets the device to the
read or erase-suspend-read mode. Address bits are
don’t cares for this command.
The reset command may be written between the sequence cycles in an erase command sequence before
erasing begins. This resets the device to the read
mode. Once erasure begins, however, the device ignores reset commands until the operation is complete.
The reset command may be written between the
sequence cycles in a program command sequence
before programming begins. This resets the device to
the read mode. If the program command sequence is
written while the device is in the Erase Suspend mode,
writing the reset command returns the device to the
erase-suspend-read mode. Once programming begins, however, the device ignores reset commands
until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command sequence.
Once in the autoselect mode, the reset command
must be written to return to the read mode. If the device entered the autoselect mode while in the Erase
Suspend mode, writing the reset command returns the
device to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation,
writing the reset command returns the device to the
read mode (or erase-suspend-read mode if the device
was in Erase Suspend).
Note that if DQ1 goes high during a Write Buffer Programming operation, the system must write the
Write-to-Buffer-Abort Reset command sequence to
reset the device for the next operation.
Autoselect Command Sequence
The autoselect command sequence allows the host
system to read several identifier codes at specific addresses:
A7:A0
(x16)
Identifier Code
A6:A-1
(x8)
Manufacturer ID
00h
00h
Device ID, Cycle 1
01h
02h
Device ID, Cycle 2
0Eh
1Ch
Device ID, Cycle 3
0Fh
1Eh
SecSi Sector Factory Protect
03h
06h
Sector Protect Verify
(SA)02h
(SA)04h
Note: The device ID is read over three cycles. SA = Sector Address
Tables 10 and 11 show the address requirements and
codes. This method is an alternative to that shown in
Table 3, which is intended for PROM programmers
and requires VID on address pin A9. The autoselect
command sequence may be written to an address that
is either in the read or erase-suspend-read mode. The
autoselect command may not be written while the device is actively programming or erasing.
The autoselect command sequence is initiated by first
writing two unlock cycles. This is followed by a third
write cycle that contains the autoselect command. The
device then enters the autoselect mode. The system
may read at any address any number of times without
initiating another autoselect command sequence:
The system must write the reset command to return to
the read mode (or erase-suspend-read mode if the device was previously in Erase Suspend).
Enter SecSi Sector/Exit SecSi Sector
Command Sequence
The SecSi Sector region provides a secured data area
containing an 8-word/16-byte random Electronic Serial
Number (ESN). The system can access the SecSi
Sector region by issuing the three-cycle Enter SecSi
December 14, 2005
Sector command sequence. The device continues to
access the SecSi Sector region until the system issues the four-cycle Exit SecSi Sector command sequence. The Exit SecSi Sector command sequence
returns the device to normal operation. Tables 10 and
11 show the address and data requirements for both
command sequences. See also “SecSi (Secured Silicon) Sector Flash Memory Region” for further information. Note that the ACC function and unlock bypass
modes are not available when the SecSi Sector is enabled.
Word/Byte Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two
unlock write cycles, followed by the program set-up
command. The program address and data are written
next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further
controls or timings. The device automatically provides
internally generated program pulses and verifies the
programmed cell margin. Tables 10 and 11 show the
address and data requirements for the word/byte program command sequence, respectively.
Am29LV640MH/L
25
D A T A S H E E T
When the Embedded Program algorithm is complete,
the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by using
DQ7 or DQ6. Refer to the Write Operation Status section for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a
hardware reset immediately terminates the program
operation. The program command sequence should
be reinitiated once the device has returned to the read
mode, to ensure data integrity. Note that the ACC
function and unlock bypass modes are not available
when the SecSi Sector is enabled.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed
from “0” back to a “1.” Attempting to do so may
cause the device to set DQ5 = 1, or cause the DQ7
and DQ6 status bits to indicate the operation was successful. However, a succeeding read will show that the
data is still “0.” Only erase operations can convert a “0”
to a “1.”
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program words to the device faster than using the standard program command sequence. The unlock bypass
command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. The device
then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is
required to program in this mode. The first cycle in this
sequence contains the unlock bypass program command, A0h; the second cycle contains the program
address and data. Additional data is programmed in
the same manner. This mode dispenses with the initial
two unlock cycles required in the standard program
command sequence, resulting in faster total programming time. Tables 10 and 11 show the requirements
for the command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands
are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset command sequence. The first cycle must contain the data
90h. The second cycle must contain the data 00h. The
device then returns to the read mode.
Write Buffer Programming
Write Buffer Programming allows the system write to a
maximum of 16 words/32 bytes in one programming
operation. This results in faster effective programming
time than the standard programming algorithms. The
Write Buffer Programming command sequence is initiated by first writing two unlock cycles. This is followed
26
by a third write cycle containing the Write Buffer Load
command written at the Sector Address in which programming will occur. The fourth cycle writes the sector
address and the number of word locations, minus one,
to be programmed. For example, if the system will program 6 unique address locations, then 05h should be
written to the device. This tells the device how many
write buffer addresses will be loaded with data and
therefore when to expect the Program Buffer to Flash
command. The number of locations to program cannot
exceed the size of the write buffer or the operation will
abort.
The fifth cycle writes the first address location and
data to be programmed. The write-buffer-page is selected by address bits AMAX–A4. All subsequent add r e s s / d a t a p a i r s m u s t fa l l w i t h i n t h e
selected-write-buffer-page. The system then writes the
remaining address/data pairs into the write buffer.
Write buffer locations may be loaded in any order.
The write-buffer-page address must be the same for
all address/data pairs loaded into the write buffer.
(This means Write Buffer Programming cannot be performed across multiple write-buffer pages. This also
means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts
to load programming data outside of the selected
write-buffer page, the operation will abort.
Note that if a Write Buffer address location is loaded
multiple times, the address/data pair counter will be
decremented for every data load operation. The host
s y s t e m m u s t t h e r e fo r e a c c o u n t fo r l o a d i n g a
write-buffer location more than once. The counter
decrements for each data load operation, not for each
unique write-buffer-address location. Note also that if
an address location is loaded more than once into the
buffer, the final data loaded for that address will be
programmed.
Once the specified number of write buffer locations
have been loaded, the system must then write the Program Buffer to Flash command at the sector address.
Any other address and data combination aborts the
Write Buffer Programming operation. The device then
begins programming. Data polling should be used
while monitoring the last address location loaded into
the write buffer. DQ7, DQ6, DQ5, and DQ1 should be
monitored to determine the device status during Write
Buffer Programming.
The write-buffer programming operation can be suspended using the standard program suspend/resume
commands. Upon successful completion of the Write
Buffer Programming operation, the device is ready to
execute the next command.
The Write Buffer Programming Sequence can be
aborted in the following ways:
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
■ Load a value that is greater than the page buffer
size during the Number of Locations to Program
step.
quired when using Write-Buffer-Programming features
in Unlock Bypass mode.
■ Write to an address in a sector different than the
one specified during the Write-Buffer-Load command.
Accelerated Program
■ Write an Address/Data pair to a different
write-buffer-page than the one selected by the
Starting Address during the write buffer data loading stage of the operation.
■ Write data other than the Confirm Command after
the specified number of data load cycles.
The abort condition is indicated by DQ1 = 1, DQ7 =
DATA# (for the last address location loaded), DQ6 =
toggle, and DQ5=0. A Write-to-Buffer-Abort Reset
command sequence must be written to reset the device for the next operation. Note that the full 3-cycle
Write-to-Buffer-Abort Reset command sequence is re-
December 14, 2005
The device offers accelerated program operations
through the WP#/ACC pin. When the system asserts
VHH on the WP#/ACC pin, the device automatically enters the Unlock Bypass mode. The system may then
write the two-cycle Unlock Bypass program command
sequence. The device uses the higher voltage on the
WP#/ACC pin to accelerate the operation. Note that
the WP#/ACC pin must not be at VHH for operations
other than accelerated programming, or device damage may result. In addition, no external pullup is necessary since the WP#/ACC pin has internal pullup to
VCC.
Figure 5 illustrates the algorithm for the program operation. Refer to the Erase and Program Operations
table in the AC Characteristics section for parameters,
and Figure 17 for timing diagrams.
Am29LV640MH/L
27
D A T A S H E E T
Write “Write to Buffer”
command and
Sector Address
Part of “Write to Buffer”
Command Sequence
Write number of addresses
to program minus 1(WC)
and Sector Address
Write first address/data
Yes
WC = 0 ?
No
Write to a different
sector address
Abort Write to
Buffer Operation?
Yes
Write to buffer ABORTED.
Must write “Write-to-buffer
Abort Reset” command
sequence to return
to read mode.
No
(Note 1)
Write next address/data pair
WC = WC - 1
Write program buffer to
flash sector address
Notes:
Read DQ7 - DQ0 at
Last Loaded Address
When Sector Address is specified, any address in
the selected sector is acceptable. However, when
loading Write-Buffer address locations with data, all
addresses must fall within the selected Write-Buffer
Page.
2.
DQ7 may change simultaneously with DQ5.
Therefore, DQ7 should be verified.
3.
If this flowchart location was reached because
DQ5= “1”, then the device FAILED. If this flowchart
location was reached because DQ1= “1”, then the
Write to Buffer operation was ABORTED. In either
case, the proper reset command must be written
before the device can begin another operation. If
DQ1=1, write the
Write-Buffer-Programming-Abort-Reset
command. if DQ5=1, write the Reset command.
4.
See Table 11 for command sequences required for
write buffer programming.
Yes
DQ7 = Data?
No
1.
No
No
DQ1 = 1?
DQ5 = 1?
Yes
Yes
Read DQ7 - DQ0 with
address = Last Loaded
Address
(Note 2)
DQ7 = Data?
Yes
No
(Note 3)
FAIL or ABORT
Figure 4.
28
PASS
Write Buffer Programming Operation
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
START
Write Program
Command Sequence
Data Poll
from System
Embedded
Program
algorithm
in progress
Verify Data?
No
Yes
No
Increment Address
Last Address?
Yes
Programming
Completed
Note: See Table 11 for program command sequence.
Figure 5.
Program Operation
Program Suspend/Program Resume
Command Sequence
autoselect, and CFI functions are unavailable when an
program operation is in progress.
The Program Suspend command allows the system to
interrupt a programming operation or a Write to Buffer
programming operation so that data can be read from
any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the program operation within 15
μs maximum (5 μs typical) and updates the status bits.
Addresses are not required when writing the Program
Suspend command.
The system may also write the autoselect command
sequence when the device is in the Program Suspend
mode. The system can read as many autoselect
codes as required. When the device exits the autoselect mode, the device reverts to the Program Suspend
mode, and is ready for another valid operation. See
Autoselect Command Sequence for more information.
After the programming operation has been suspended, the system can read array data from any
non-suspended sector. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data
may be read from any addresses not in Erase Suspend or Program Suspend. If a read is needed from
the SecSi Sector area (One-time Program area), then
user must use the proper command sequences to
enter and exit this region. Note that the SecSi Sector,
December 14, 2005
After the Program Resume command is written, the
device reverts to programming. The system can determine the status of the program operation using the
DQ7 or DQ6 status bits, just as in the standard program operation. See Write Operation Status for more
information.
The system must write the Program Resume command (address bits are don’t care) to exit the Program
Suspend mode and continue the programming operation. Further writes of the Resume command are ignored. Another Program Suspend command can be
written after the device has resume programming.
Am29LV640MH/L
29
D A T A S H E E T
Program Operation
or Write-to-Buffer
Sequence in Progress
Write address/data
XXXh/B0h
Write Program Suspend
Command Sequence
Command is also valid for
Erase-suspended-program
operations
Wait 15 μs
Autoselect and SecSi Sector
read operations are also allowed
Read data as
required
No
Data cannot be read from erase- or
program-suspended sectors
Done
reading?
Yes
Write address/data
XXXh/30h
Write Program Resume
Command Sequence
Device reverts to
operation prior to
Program Suspend
Figure 6.
Program Suspend/Program Resume
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase
command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional
unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase
algorithm. The device does not require the system to
preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical
erase. The system is not required to provide any controls or timings during these operations. Tables 10 and
11 show the address and data requirements for the
chip erase command sequence.
When the Embedded Erase algorithm is complete, the
device returns to the read mode and addresses are no
longer latched. The system can determine the status
of the erase operation by using DQ7, DQ6, or DQ2.
Refer to the Write Operation Status section for information on these status bits.
Any commands written during the chip erase operation
are ignored. However, note that a hardware reset im-
30
mediately terminates the erase operation. If that occurs, the chip erase command sequence should be
reinitiated once the device has returned to reading
array data, to ensure data integrity. Note that the
SecSi Sector, autoselect, and CFI functions are unavailable when an erase operation is in progress.
Figure 7 illustrates the algorithm for the erase operation. Refer to the Erase and Program Operations tables in the AC Characteristics section for parameters,
and Figure 19 section for timing diagrams.
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector
erase command sequence is initiated by writing two
unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed by the address of the sector to be erased, and
the sector erase command. Tables 10 and 11 show the
address and data requirements for the sector erase
command sequence.
The device does not require the system to preprogram
prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
an all zero data pattern prior to electrical erase. The
system is not required to provide any controls or timings during these operations.
After the command sequence is written, a sector erase
time-out of 50 µs occurs. During the time-out period,
additional sector addresses and sector erase commands may be written. Loading the sector erase buffer
may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time
between these additional cycles must be less than 50
µs, otherwise erasure may begin. Any sector erase address and command following the exceeded time-out
may or may not be accepted. It is recommended that
processor interrupts be disabled during this time to ensure all commands are accepted. The interrupts can
be re-enabled after the last Sector Erase command is
written. Any command other than Sector Erase or
Erase Suspend during the time-out period resets
the device to the read mode. The system must rewrite the command sequence and any additional addresses and commands. Note that the SecSi Sector,
autoselect, and CFI functions are unavailable when an
erase operation is in progress.
The system can monitor DQ3 to determine if the sector erase timer has timed out (See the section on DQ3:
Sector Erase Timer.). The time-out begins from the rising edge of the final WE# pulse in the command
sequence.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses
are no longer latched. The system can determine the
status of the erase operation by reading DQ7, DQ6, or
DQ2 in the erasing sector. Refer to the Write Operation Status section for information on these status bits.
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands are ignored. However, note that a hardware
reset immediately terminates the erase operation. If
that occurs, the sector erase command sequence
should be reinitiated once the device has returned to
reading array data, to ensure data integrity.
Figure 7 illustrates the algorithm for the erase operation. Refer to the Erase and Program Operations tables in the AC Characteristics section for parameters,
and Figure 19 section for timing diagrams.
START
Write Erase
Command Sequence
(Notes 1, 2)
Data Poll to Erasing
Bank from System
No
Embedded
Erase
algorithm
in progress
Data = FFh?
Yes
Erasure Completed
Notes:
1. See Tables 10 and 11 for erase command sequence.
2. See the section on DQ3 for information on the sector erase timer.
Figure 7.
December 14, 2005
Erase Operation
Am29LV640MH/L
31
D A T A S H E E T
Erase Suspend/Erase Resume
Commands
The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read
data from, or program data to, any sector not selected
for erasure. This command is valid only during the sector erase operation, including the 50 µs time-out period during the sector erase command sequence. The
Erase Suspend command is ignored if written during
the chip erase operation or Embedded Program
algorithm.
When the Erase Suspend command is written during
the sector erase operation, the device requires a maximum of 20 (typical 5 µs) to suspend the erase operation. However, when the Erase Suspend command is
written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation.
After the erase operation has been suspended, the
device enters the erase-suspend-read mode. The system can read data from or program data to any sector
not selected for erasure. (The device “erase suspends” all sectors selected for erasure.) Reading at
any address within erase-suspended sectors produces status information on DQ7–DQ0. The system
can use DQ7, or DQ6 and DQ2 together, to determine
if a sector is actively erasing or is erase-suspended.
Refer to the Write Operation Status section for information on these status bits.
32
After an erase-suspended program operation is complete, the device returns to the erase-suspend-read
mode. The system can determine the status of the
program operation using the DQ7 or DQ6 status bits,
just as in the standard word program operation.
Refer to the Write Operation Status section for more
information.
In the erase-suspend-read mode, the system can also
issue the autoselect command sequence. Refer to the
Autoselect Mode and Autoselect Command Sequence
sections for details.
To resume the sector erase operation, the system
must write the Erase Resume command. Further
writes of the Resume command are ignored. Another
Erase Suspend command can be written after the chip
has resumed erasing.
Note: During an erase operation, this flash device performs multiple internal operations which are invisible
to the system. When an erase operation is suspended,
any of the internal operations that were not fully completed must be restarted. As such, if this flash device
is continually issued suspend/resume commands in
rapid succession, erase progress will be impeded as a
function of the number of suspends. The result will be
a longer cumulative erase time than without suspends.
Note that the additional suspends do not affect device
reliability or future performance. In most systems rapid
erase/suspend activity occurs only briefly. In such
cases, erase performance will not be significantly impacted.
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
Command Definitions
Command
Sequence
(Note 1)
Read (Note 5)
Command Definitions (x16 Mode, BYTE# = VIH)
Bus Cycles (Notes 2–5)
First
Second
Addr
Data
1
RA
RD
Addr
Data
Third
Addr
Fourth
Data
Addr
Fifth
Data
Sixth
Addr
Data
Addr
Data
X0E
220C
X0F
2201
PD
1
XXX
F0
Manufacturer ID
4
555
AA
2AA
55
555
90
X00
0001
Device ID (Note 8)
6
555
AA
2AA
55
555
90
X01
227E
SecSi™ Sector Factory Protect
(Note 9)
4
555
AA
2AA
55
555
90
X03
(Note 10)
Sector Group Protect Verify
(Note 10)
4
555
AA
2AA
55
555
90
(SA)X02
00/01
Enter SecSi Sector Region
3
555
AA
2AA
55
555
88
Exit SecSi Sector Region
4
555
AA
2AA
55
555
90
XXX
00
Program
4
555
AA
2AA
55
555
A0
PA
PD
Write to Buffer (Note 11)
6
555
AA
2AA
55
SA
25
SA
WC
PA
PD
WBL
Program Buffer to Flash
1
SA
29
Autoselect (Note 7)
Reset (Note 6)
Cycles
Table 8.
Write to Buffer Abort Reset (Note 12)
3
555
AA
2AA
55
555
F0
Unlock Bypass
3
555
AA
2AA
55
555
20
Unlock Bypass Program (Note 13)
2
XXX
A0
PA
PD
Unlock Bypass Reset (Note 14)
2
XXX
90
XXX
00
Chip Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
555
10
Sector Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
SA
30
Program/Erase Suspend (Note 15)
1
XXX
B0
Program/Erase Resume (Note 16)
1
XXX
30
CFI Query (Note 17)
1
55
98
Legend:
X = Don’t care
RA = Read Address of memory location to be read.
RD = Read Data read from location RA during read operation.
PA = Program Address . Addresses latch on falling edge of WE# or
CE# pulse, whichever happens later.
PD = Program Data for location PA. Data latches on rising edge of
WE# or CE# pulse, whichever happens first.
SA = Sector Address of sector to be verified (in autoselect mode) or
erased. Address bits A21–A15 uniquely select any sector.
WBL = Write Buffer Location. Address must be within same write
buffer page as PA.
WC = Word Count. Number of write buffer locations to load minus 1.
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
See Table 1 for description of bus operations.
All values are in hexadecimal.
Shaded cells indicate read cycles. All others are write cycles.
During unlock and command cycles, when lower address bits are
555 or 2AA as shown in table, address bits above A11 and data
bits above DQ7 are don’t care.
No unlock or command cycles required when device is in read
mode.
Reset command is required to return to read mode (or to
erase-suspend-read mode if previously in Erase Suspend) when
device is in autoselect mode, or if DQ5 goes high while device is
providing status information.
Fourth cycle of the autoselect command sequence is a read
cycle. Data bits DQ15–DQ8 are don’t care. Except for RD, PD
and WC. See Autoselect Command Sequence section for more
information.
Device ID must be read in three cycles.
9.
10.
11.
12.
13.
14.
15.
16.
December 14, 2005
If WP# protects highest address sector, data is 98h for factory
locked and 18h for not factory locked. If WP# protects lowest
address sector, data is 88h for factory locked and 08h for not
factor locked.
Data is 00h for an unprotected sector group and 01h for a
protected sector group.
Total number of cycles in command sequence is determined by
number of words written to write buffer. Maximum number of
cycles in command sequence is 21, including "Program Buffer to
Flash" command.
Command sequence resets device for next command after
aborted write-to-buffer operation.
Unlock Bypass command is required prior to Unlock Bypass
Program command.
Unlock Bypass Reset command is required to return to read
mode when device is in unlock bypass mode.
System may read and program in non-erasing sectors, or enter
autoselect mode, when in Erase Suspend mode. Erase Suspend
command is valid only during a sector erase operation.
Erase Resume command is valid only during Erase Suspend
mode.
Am29LV640MH/L
33
D A T A S H E E T
Command
Sequence
(Note 1)
Read (Note 6)
Autoselect (Note 8)
Reset (Note 7)
Cycles
Table 9.
1
Command Definitions (x8 Mode, BYTE# = VIL)
Bus Cycles (Notes 2–5)
First
Second
Addr
Data
RA
RD
Third
Fourth
Fifth
Addr
Data
Addr
Data
Addr
Data
1
XXX
F0
Manufacturer ID
4
AAA
AA
555
55
AAA
90
X00
01
Device ID (Note 9)
6
AAA
AA
555
55
AAA
90
X02
7E
SecSi™ Sector Factory Protect
(Note 10)
4
AAA
AA
555
55
AAA
90
X06
(Note 10)
Sector Group Protect Verify
(Note 11)
4
AAA
AA
555
55
AAA
90
(SA)X04
00/01
XXX
00
Sixth
Addr
Data
Addr
Data
X1C
0C
X1E
01
Enter SecSi Sector Region
3
AAA
AA
555
55
AAA
88
Exit SecSi Sector Region
4
AAA
AA
555
55
AAA
90
Program
4
AAA
AA
555
55
AAA
A0
PA
PD
Write to Buffer (Note 12)
6
AAA
AA
555
55
SA
25
SA
BC
PA
PD
WBL
PD
Program Buffer to Flash
1
SA
29
Write to Buffer Abort Reset (Note 13)
3
AAA
AA
555
55
AAA
F0
Unlock Bypass
3
AAA
AA
555
55
AAA
20
Unlock Bypass Program (Note 14)
2
XXX
A0
PA
PD
Unlock Bypass Reset (Note 15)
2
XXX
90
XXX
00
Chip Erase
6
AAA
AA
555
55
AAA
80
AAA
AA
555
55
AAA
10
Sector Erase
6
AAA
AA
555
55
AAA
80
AAA
AA
555
55
SA
30
Program/Erase Suspend (Note 16)
1
XXX
B0
Program/Erase Resume (Note 17)
1
XXX
30
CFI Query (Note 18)
1
AA
98
Legend:
X = Don’t care
RA = Read Address of memory location to be read.
RD = Read Data read from location RA during read operation.
PA = Program Address . Addresses latch on falling edge of WE# or
CE# pulse, whichever happens later.
PD = Program Data for location PA. Data latches on rising edge of
WE# or CE# pulse, whichever happens first.
SA = Sector Address of sector to be verified (in autoselect mode) or
erased. Address bits A21–A15 uniquely select any sector.
WBL = Write Buffer Location. Address must be within same write
buffer page as PA.
BC = Byte Count. Number of write buffer locations to load minus 1.
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
34
See Table 1 for description of bus operations.
All values are in hexadecimal.
Shaded cells indicate read cycles. All others are write cycles.
During unlock and command cycles, when lower address bits are
555 or AAA as shown in table, address bits above A11 are don’t
care.
Unless otherwise noted, address bits A21–A11 are don’t cares.
No unlock or command cycles required when device is in read
mode.
Reset command is required to return to read mode (or to
erase-suspend-read mode if previously in Erase Suspend) when
device is in autoselect mode, or if DQ5 goes high while device is
providing status information.
Fourth cycle of autoselect command sequence is a read cycle.
Data bits DQ15–DQ8 are don’t care. See Autoselect Command
Sequence section or more information.
Device ID must be read in three cycles.
10. If WP# protects highest address sector, data is 98h for factory
locked and 18h for not factory locked. If WP# protects lowest
address sector, data is 88h for factory locked and 08h for not
factor locked.
11. Data is 00h for an unprotected sector group and 01h for a
protected sector group.
12. Total number of cycles in command sequence is determined by
number of bytes written to write buffer. Maximum number of
cycles in command sequence is 37, including "Program Buffer to
Flash" command.
13. Command sequence resets device for next command after
aborted write-to-buffer operation.
14. Unlock Bypass command is required prior to Unlock Bypass
Program command.
15. Unlock Bypass Reset command is required to return to read
mode when device is in unlock bypass mode.
16. System may read and program in non-erasing sectors, or enter
autoselect mode, when in Erase Suspend mode. Erase Suspend
command is valid only during a sector erase operation.
17. Erase Resume command is valid only during Erase Suspend
mode.
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
WRITE OPERATION STATUS
The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5,
DQ6, and DQ7. Table 12 and the following subsections describe the function of these bits. DQ7 and DQ6
each offer a method for determining whether a program or erase operation is complete or in progress.
The device also provides a hardware-based output
signal, RY/BY#, to determine whether an Embedded
Program or Erase operation is in progress or has been
completed.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or completed, or whether the
device is in Erase Suspend. Data# Polling is valid after
the rising edge of the final WE# pulse in the command
sequence.
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the
Embedded Program algorithm is complete, the device
outputs the datum programmed to DQ7. The system
must provide the program address to read valid status
information on DQ7. If a program address falls within a
protected sector, Data# Polling on DQ7 is active for
approximately 1 µs, then the device returns to the read
mode.
algorithm is complete, or if the device enters the Erase
Suspend mode, Data# Polling produces a “1” on DQ7.
The system must provide an address within any of the
sectors selected for erasure to read valid status information on DQ7.
After an erase command sequence is written, if all
sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 µs, then the
device returns to the read mode. If not all selected
sectors are protected, the Embedded Erase algorithm
erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected
sector, the status may not be valid.
Just prior to the completion of an Embedded Program
or Erase operation, DQ7 may change asynchronously
with DQ0–DQ6 while Output Enable (OE#) is asserted
low. That is, the device may change from providing
status information to valid data on DQ7. Depending on
when the system samples the DQ7 output, it may read
the status or valid data. Even if the device has completed the program or erase operation and DQ7 has
valid data, the data outputs on DQ0–DQ6 may be still
invalid. Valid data on DQ0–DQ7 will appear on successive read cycles.
Table 12 shows the outputs for Data# Polling on DQ7.
Figure 8 shows the Data# Polling algorithm. Figure 20
in the AC Characteristics section shows the Data#
Polling timing diagram.
During the Embedded Erase algorithm, Data# Polling
produces a “0” on DQ7. When the Embedded Erase
December 14, 2005
Am29LV640MH/L
35
D A T A S H E E T
START
Read DQ7–DQ0
Addr = VA
DQ7 = Data?
Yes
No
No
DQ5 = 1?
Yes
Read DQ7–DQ0
Addr = VA
DQ7 = Data?
Yes
No
FAIL
PASS
Notes:
1. VA = Valid address for programming. During a sector erase operation, a valid
address is any sector address within the sector being erased. During chip erase, a
valid address is any non-protected sector address.
2. DQ7 should be rechecked even if DQ5 = “1” because DQ7 may change simultaneously with DQ5.
Figure 8.
36
Data# Polling Algorithm
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
RY/BY#: Ready/Busy#
The RY/BY# is a dedicated, open-drain output pin
which indicates whether an Embedded Algorithm is in
progress or complete. The RY/BY# status is valid after
the rising edge of the final WE# pulse in the command
sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a
pull-up resistor to VCC.
If the output is low (Busy), the device is actively erasing or programming. (This includes programming in
the Erase Suspend mode.) If the output is high
(Ready), the device is in the read mode, the standby
mode, or in the erase-suspend-read mode. Table 12
shows the outputs for RY/BY#.
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase
Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final
WE# pulse in the command sequence (prior to the
program or erase operation), and during the sector
erase time-out.
During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause
DQ6 to toggle. The system may use either OE# or
CE# to control the read cycles. When the operation is
complete, DQ6 stops toggling.
December 14, 2005
After an erase command sequence is written, if all
sectors selected for erasing are protected, DQ6 toggles for approximately 100 µs, then returns to reading
array data. If not all selected sectors are protected, the
Embedded Erase algorithm erases the unprotected
sectors, and ignores the selected sectors that are protected.
The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is
erase-suspended. When the device is actively erasing
(that is, the Embedded Erase algorithm is in progress),
DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system
must also use DQ2 to determine which sectors are
erasing or erase-suspended. Alternatively, the system
can use DQ7 (see the subsection on DQ7: Data# Polling).
If a program address falls within a protected sector,
DQ6 toggles for approximately 1 μs after the program
command sequence is written, then returns to reading
array data.
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded Program algorithm is complete.
Table 12 shows the outputs for Toggle Bit I on DQ6.
Figure 9 shows the toggle bit algorithm. Figure 21 in
the “AC Characteristics” section shows the toggle bit
timing diagrams. Figure 22 shows the differences between DQ2 and DQ6 in graphical form. See also the
subsection on DQ2: Toggle Bit II.
Am29LV640MH/L
37
D A T A S H E E T
START
Read DQ7–DQ0
Read DQ7–DQ0
Toggle Bit
= Toggle?
No
Yes
No
DQ5 = 1?
Yes
Read DQ7–DQ0
Twice
Toggle Bit
= Toggle?
No
Yes
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Note: The system should recheck the toggle bit even if DQ5 = “1” because the toggle
bit may stop toggling as DQ5 changes to “1.” See the subsections on DQ6 and DQ2
for more information.
Figure 9.
Toggle Bit Algorithm
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing
(that is, the Embedded Erase algorithm is in progress),
or whether that sector is erase-suspended. Toggle Bit
II is valid after the rising edge of the final WE# pulse in
the command sequence.
DQ2 toggles when the system reads at addresses
within those sectors that have been selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish
38
whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the
device is actively erasing, or is in Erase Suspend, but
cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and
mode information. Refer to Table 12 to compare outputs for DQ2 and DQ6.
Figure 9 shows the toggle bit algorithm in flowchart
form, and the section “DQ2: Toggle Bit II” explains the
algorithm. See also the RY/BY#: Ready/Busy# subsection. Figure 21 shows the toggle bit timing diagram.
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
Figure 22 shows the differences between DQ2 and
DQ6 in graphical form.
Reading Toggle Bits DQ6/DQ2
Refer to Figure 9 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically,
the system would note and store the value of the toggle bit after the first read. After the second read, the
system would compare the new value of the toggle bit
with the first. If the toggle bit is not toggling, the device
has completed the program or erase operation. The
system can read array data on DQ7–DQ0 on the following read cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should
then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling
just as DQ5 went high. If the toggle bit is no longer
toggling, the device has successfully completed the
program or erase operation. If it is still toggling, the device did not completed the operation successfully, and
the system must write the reset command to return to
reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has
not gone high. The system may continue to monitor
the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform
other system tasks. In this case, the system must start
at the beginning of the algorithm when it returns to determine the status of the operation (top of Figure 9).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program, erase, or
write-to-buffer time has exceeded a specified internal
pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the program or erase cycle
was not successfully completed.
The device may output a “1” on DQ5 if the system tries
to program a “1” to a location that was previously pro-
December 14, 2005
grammed to “0.” Only an erase operation can
change a “0” back to a “1.” Under this condition, the
device halts the operation, and when the timing limit
has been exceeded, DQ5 produces a “1.”
In all these cases, the system must write the reset
command to return the device to the reading the array
(or to erase-suspend-read if the device was previously
in the erase-suspend-program mode).
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not
erasure has begun. (The sector erase timer does not
apply to the chip erase command.) If additional
sectors are selected for erasure, the entire time-out
also applies after each additional sector erase command. When the time-out period is complete, DQ3
switches from a “0” to a “1.” If the time between additional sector erase commands from the system can be
assumed to be less than 50 µs, the system need not
monitor DQ3. See also the Sector Erase Command
Sequence section.
After the sector erase command is written, the system
should read the status of DQ7 (Data# Polling) or DQ6
(Toggle Bit I) to ensure that the device has accepted
the command sequence, and then read DQ3. If DQ3 is
“1,” the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the
device will accept additional sector erase commands.
To ensure the command has been accepted, the system software should check the status of DQ3 prior to
and following each subsequent sector erase command. If DQ3 is high on the second status check, the
last command might not have been accepted.
Table 12 shows the status of DQ3 relative to the other
status bits.
DQ1: Write-to-Buffer Abort
DQ1 indicates whether a Write-to-Buffer operation
was aborted. Under these conditions DQ1 produces a
“1”.
The
system
must
issue
the
Write-to-Buffer-Abort-Reset command sequence to return the device to reading array data. See Write Buffer
Programming section for more details.
Am29LV640MH/L
39
D A T A S H E E T
Table 10.
Standard
Mode
Program
Suspend
Mode
Erase
Suspend
Mode
Write-toBuffer
Write Operation Status
DQ7
Status
(Note 2)
Embedded Program Algorithm
DQ7#
Embedded Erase Algorithm
0
Program-Suspended
Program- Sector
Suspend
Non-Program
Read
Suspended Sector
Erase-Suspended
1
EraseSector
Suspend
Non-Erase Suspended
Read
Sector
Erase-Suspend-Program
DQ7#
(Embedded Program)
Busy (Note 3)
DQ7#
Abort (Note 4)
DQ7#
DQ6
Toggle
Toggle
No toggle
DQ5
(Note 1)
0
0
DQ3
N/A
1
DQ2
(Note 2)
No toggle
Toggle
DQ1
0
N/A
RY/BY#
0
0
Invalid (not allowed)
1
Data
1
0
N/A
Toggle
N/A
Data
1
1
Toggle
0
N/A
N/A
N/A
0
Toggle
Toggle
0
0
N/A
N/A
N/A
N/A
0
1
0
0
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program, Embedded Erase, or Write-to-Buffer operation has exceeded the
maximum timing limits. Refer to the section on DQ5 for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address location.
4. DQ1 switches to ‘1’ when the device has aborted the write-to-buffer operation.
40
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
ABSOLUTE MAXIMUM RATINGS
Storage Temperature, Plastic Packages . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Ambient Temperature with Power Applied . . . . . . . . . . . . . . . . . . –65°C to +125°C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–0.5 V to +4.0 V
VIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–0.5 V to +4.0 V
A9, OE#, ACC, and RESET# (Note 2) . . . . . . . . . . . . . .–0.5 V to +12.5 V
All other pins (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions,
input or I/O pins may overshoot VSS to –2.0 V for periods of up to 20 ns. Maximum
DC voltage on input or I/O pins is VCC +0.5 V. See Figure 10. During voltage
transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns.
See Figure 11.
2. Minimum DC input voltage on pins A9, OE#, ACC, and RESET# is –0.5 V. During
voltage transitions, A9, OE#, ACC, and RESET# may overshoot VSS to –2.0 V for
periods of up to 20 ns. See Figure 10. Maximum DC input voltage on pin A9, OE#,
ACC, and RESET# is +12.5 V which may overshoot to +14.0 V for periods up to
20 ns.
3. No more than one output may be shorted to ground at a time. Duration of the short
circuit should not be greater than one second.
Stresses above those listed under “Absolute Maximum Ratings” may cause permanent
damage to the device. This is a stress rating only; functional operation of the device
at these or any other conditions above those indicated in the operational sections of
this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability.
20 ns
20 ns
20 ns
VCC
+2.0 V
VCC
+0.5 V
+0.8 V
–0.5 V
–2.0 V
2.0 V
20 ns
20 ns
Figure 10. Maximum Negative
Overshoot Waveform
20 ns
Figure 11. Maximum Positive
Overshoot Waveform
OPERATING RANGES
Industrial (I) Devices
Ambient Temperature (TA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Supply Voltages
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7–3.6 V
VIO (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.65–3.6 V
Notes:
1. Operating ranges define those limits between which the functionality of the device
is guaranteed.
2. See Ordering Information section for valid VCC/VIO range combinations. The I/Os
will not operate at 3 V when VIO = 1.8 V.
December 14, 2005
Am29LV640MH/L
41
D A T A S H E E T
DC CHARACTERISTICS
CMOS Compatible
Parameter
Symbol
Parameter Description
(Notes)
Test Conditions
Min
Unit
±1.0
µA
Input Load Current (1)
VIN = VSS to VCC,
VCC = VCC max
ILIT
A9, ACC Input Load Current
VCC = VCC max; A9 = 12.5 V
35
µA
ILR
Reset Leakage Current
VCC = VCC max; RESET# = 12.5 V
35
µA
ILO
Output Leakage Current
VOUT = VSS to VCC,
VCC = VCC max
±1.0
µA
ICC1
VCC Active Read Current (2, 3)
CE# = VIL, OE# = VIH,
ICC2
VCC Initial Page Read Current (2, 3)
ICC3
5 MHz
15
20
1 MHz
15
20
CE# = VIL, OE# = VIH
30
50
mA
VCC Intra-Page Read Current (2, 3)
CE# = VIL, OE# = VIH
10
20
mA
ICC4
VCC Active Write Current (3, 4)
CE# = VIL, OE# = VIH
50
60
mA
ICC5
VCC Standby Current (3)
CE#, RESET# = VCC ± 0.3 V,
WP# = VIH
1
5
µA
ICC6
VCC Reset Current (3)
RESET# = VSS ± 0.3 V, WP# = VIH
1
5
µA
ICC7
Automatic Sleep Mode (3, 5)
VIH = VCC ± 0.3 V;
VIL = VSS ± 0.3 V, WP# = VIH
1
5
µA
VIL1
Input Low Voltage 1(6, 7)
–0.5
0.8
V
VIH1
Input High Voltage 1 (6, 7)
1.9
VCC + 0.5
V
V
mA
VIL2
Input Low Voltage 2 (6, 8)
–0.5
0.3 x VIO
VIH2
Input High Voltage 2 (6, 8)
1.9
VIO + 0.5
V
VHH
Voltage for ACC Program Acceleration
VCC = 2.7 –3.6 V
11.5
12.5
V
VID
Voltage for Autoselect and Temporary Sector
VCC = 2.7 –3.6 V
Unprotect
11.5
12.5
V
VOL
Output Low Voltage (9)
0.15 x VIO
V
Output High Voltage
VOH2
VLKO
IOL = 4.0 mA, VCC = VCC min = VIO
IOH = –2.0 mA, VCC = VCC min = VIO
0.85 VIO
V
IOH = –100 µA, VCC = VCC min = VIO
VIO–0.4
V
Low VCC Lock-Out Voltage (10)
2.3
Notes:
1. On the WP#/ACC pin only, the maximum input load current when
WP# = VIL is ± 5.0 µA.
6.
2.5
V
If VIO < VCC, maximum VIL for CE# and DQ I/Os is 0.3 VIO. If VIO <
VCC, minimum VIH for CE# and DQ I/Os is 0.7 VIO. Maximum VIH
for these connections is VIO + 0.3 V.
2.
The ICC current listed is typically less than 2 mA/MHz, with OE# at
VIH.
7.
VCC voltage requirements.
3.
Maximum ICC specifications are tested with VCC = VCCmax.
8.
VIO voltage requirements.
4.
ICC active while Embedded Erase or Embedded Program is in
progress.
9.
Includes RY/BY#
42
Max
ILI
VOH1
5.
Typ
10. Not 100% tested.
Automatic sleep mode enables the low power mode when
addresses remain stable for tACC + 30 ns.
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
TEST CONDITIONS
Table 11.
3.3 V
Test Condition
Output Load
Output Load Capacitance, CL
(including jig capacitance)
Input Rise and Fall Times
Input Pulse Levels
Input timing measurement
reference levels (See Note)
Output timing measurement
reference levels
2.7 kΩ
Device
Under
Test
CL
Test Specifications
6.2 kΩ
All Speeds
1 TTL gate
Unit
30
pF
5
0.0–3.0
ns
V
1.5
V
0.5 VIO
V
Note: If VIO < VCC, the reference level is 0.5 VIO.
Note: Diodes are IN3064 or equivalent
Figure 12.
Test Setup
KEY TO SWITCHING WAVEFORMS
WAVEFORM
INPUTS
OUTPUTS
Steady
Changing from H to L
Changing from L to H
3.0 V
Input
Don’t Care, Any Change Permitted
Changing, State Unknown
Does Not Apply
Center Line is High Impedance State (High Z)
1.5 V
Measurement Level
0.5 VIO V
Output
0.0 V
Note: If VIO < VCC, the input measurement reference level is 0.5 VIO.
Figure 13. Input Waveforms and
Measurement Levels
December 14, 2005
Am29LV640MH/L
43
D A T A S H E E T
AC CHARACTERISTICS
Read-Only Operations
Parameter
Speed Options
JEDEC
Std.
tAVAV
tRC
tAVQV
tELQV
Description
Test Setup
Read Cycle Time (Note 1)
CE#, OE# =
VIL
tACC Address to Output Delay
tCE
OE# = VIL
Chip Enable to Output Delay
tPACC Page Access Time
90R
101,
101R
Min
90
100
110
120
ns
Max
90
100
110
120
ns
112R
112
120R
110
120
Max
90
100
Max
25
30
30
40
30
120
40
25
30
30
40
30
40
Unit
ns
ns
tGLQV
tOE
Output Enable to Output Delay
Max
tEHQZ
tDF
Chip Enable to Output High Z (Note 1)
Max
16
ns
tGHQZ
tDF
Output Enable to Output High Z (Note 1)
Max
16
ns
tOH
Output Hold Time From Addresses, CE# or
OE#, Whichever Occurs First
Min
0
ns
Read
Output Enable Hold
Toggle and
Time (Note 1)
Data# Polling
Min
0
ns
tOEH
Min
10
ns
tAXQX
ns
Notes:
1. Not 100% tested.
2. See Figure 12 and Table 13 for test specifications.
3.
AC Specifications listed are tested with VIO = VCC. Contact AMD for
information on AC operation with VIO
≠ VCC.
tRC
Addresses Stable
Addresses
tACC
CE#
tRH
tRH
tDF
tOE
OE#
tOEH
WE#
tCE
tOH
HIGH Z
HIGH Z
Output Valid
Outputs
RESET#
RY/BY#
0V
Figure 14.
44
Read Operation Timings
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
AC CHARACTERISTICS
Same Page
A21-A2
A1-A0
Aa
Ab
tPACC
tACC
Data Bus
Qa
Ad
Ac
tPACC
Qb
tPACC
Qc
Qd
CE#
OE#
* Figure shows device in word mode. Addresses are A1–A-1 for byte mode.
Figure 15.
December 14, 2005
Page Read Timings
Am29LV640MH/L
45
D A T A S H E E T
AC CHARACTERISTICS
Hardware Reset (RESET#)
Parameter
JEDEC
Std.
tReady
tReady
tRP
tRH
tRPD
tRB
Description
RESET# Pin Low (During Embedded Algorithms) to
Read Mode (See Note)
RESET# Pin Low (NOT During Embedded
Algorithms) to Read Mode (See Note)
RESET# Pulse Width
Reset High Time Before Read (See Note)
RESET# Input Low to Standby Mode
RY/BY# Output High to CE#, OE# pin Low
All Speed Options
Unit
Max
20
μs
Max
500
ns
Min
Min
Min
Min
500
50
20
0
ns
ns
µs
ns
Notes:
1. Not 100% tested.
2. AC Specifications listed are tested with VIO = VCC. Contact AMD for information on AC operation with VIO ≠ VCC.
RY/BY#
CE#f, OE#
tRH
RESET#
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
tReady
RY/BY#
tRB
CE#f, OE#
RESET#
tRP
Figure 16.
46
Reset Timings
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
AC CHARACTERISTICS
Erase and Program Operations
Parameter
Speed Options
90R
101,
101R
112,
112R
120,
120R
Unit
90
100
110
120
ns
JEDEC
Std.
Description
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tASO
Address Setup Time to OE# low during toggle bit
polling
Min
15
ns
tAH
Address Hold Time
Min
45
ns
tAHT
Address Hold Time From CE# or OE# high
during toggle bit polling
Min
0
ns
tDVWH
tDS
Data Setup Time
Min
45
ns
tWHDX
tDH
Data Hold Time
Min
0
ns
tOEPH
Output Enable High during toggle bit polling
Min
20
ns
tGHWL
tGHWL
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
tELWL
tCS
CE# Setup Time
Min
0
ns
tWHEH
tCH
CE# Hold Time
Min
0
ns
tWLWH
tWP
Write Pulse Width
Min
35
ns
tWHDL
tWPH
Write Pulse Width High
Min
30
ns
Write Buffer Program Operation (Notes 2, 3)
Typ
352
µs
Per Byte
Typ
11
µs
Per Word
Typ
22
µs
Per Byte
Typ
8.8
µs
Per Word
Typ
17.6
µs
100
µs
100
µs
90
µs
tWLAX
Effective Write Buffer Program
Operation (Notes 2, 4)
tWHWH1
tWHWH1
Accelerated Effective Write Buffer
Program Operation (Notes 2, 4)
Byte
Single Word/Byte Program
Operation (Note 2, 5)
Word
Single Word/Byte Accelerated
Programming Operation (Note 2, 5)
tWHWH2
Byte
Word
Typ
Typ
90
µs
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.5
sec
tVHH
VHH Rise and Fall Time (Note 1)
Min
250
ns
tVCS
VCC Setup Time (Note 1)
Min
50
µs
tBUSY
WE# High to RY/BY# Low
Min
tPOLL
Program Valid Before Status Polling (Note 7)
Max
90
100
110
4
120
ns
µs
Notes:
1.
2.
3.
4.
5.
Not 100% tested.
See the “Erase and Programming Performance” section for more
information.
For 1–16 words/1–32 bytes programmed.
Effective write buffer specification is based upon a
16-word/32-byte write buffer operation.
Word/Byte programming specification is based upon a single
word/byte programming operation not utilizing the write buffer.
December 14, 2005
6.
7.
AC Specifications listed are tested with VIO = VCC. Contact AMD
for information on AC operation with VIO
VCC.
When using the program suspend/resume feature, if the
suspend command is issued within tPOLL, tPOLL must be fully
re-applied upon resuming the programming operation. If the
suspend command is issued after tPOLL, tPOLL is not required
again prior to reading the status bits upon resuming.
Am29LV640MH/L
≠
47
D A T A S H E E T
AC CHARACTERISTICS
Program Command Sequence (last two cycles)
tAS
tWC
Addresses
Read Status Data (last two cycles)
555h
PA
PA
PA
tAH
CE#
tCH
OE#
tPOLL
tWP
WE#
tWPH
tCS
tDS
tDH
PD
A0h
Data
tWHWH1
Status
tBUSY
DOUT
tRB
RY/BY#
VCC
tVCS
Notes:
1. PA = program address, PD = program data, DOUT is the true data at the program address.
ILLUSTRATION SHOWS DEVICE IN WORD MODE.
Figure 17.
Program Operation Timings
VHH
ACC
VIL or VIH
VIL or VIH
tVHH
Figure 18.
48
tVHH
Accelerated Program Timing Diagram
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
AC CHARACTERISTICS
Erase Command Sequence (last two cycles)
tAS
tWC
2AAh
Addresses
Read Status Data
VA
SA
VA
555h for chip erase
tAH
CE#
tCH
OE#
tWP
WE#
tWPH
tCS
tWHWH2
tDS
tDH
Data
55h
In
Progress
30h
Complete
10 for Chip Erase
tBUSY
tRB
RY/BY#
tVCS
VCC
Notes:
1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status”.
2. Illustration shows device in word mode.
Figure 19.
December 14, 2005
Chip/Sector Erase Operation Timings
Am29LV640MH/L
49
D A T A S H E E T
AC CHARACTERISTICS
tRC
Addresses
VA
tPOLL
VA
VA
tACC
tCE
CE#
tCH
tOE
OE#
tOEH
tDF
WE#
tOH
DQ15 and DQ7
DQ14–DQ8, DQ6–DQ0
Complement
Complement
Status Data
Status Data
True
True
Valid Data
Valid Data
High Z
High Z
tBUSY
RY/BY#
Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data
read cycle.
Figure 20. Data# Polling Timings
(During Embedded Algorithms)
50
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
AC CHARACTERISTICS
tAHT
tAS
Addresses
tAHT
tASO
CE#
tCEPH
tOEH
WE#
tOEPH
OE#
tDH
DQ6/DQ2
tOE
Valid Data
Valid
Status
Valid
Status
Valid
Status
(first read)
(second read)
(stops toggling)
Valid Data
RY/BY#
Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status
read cycle, and array data read cycle.
Figure 21.
Enter
Embedded
Erasing
WE#
Erase
Suspend
Erase
Toggle Bit Timings (During Embedded Algorithms)
Enter Erase
Suspend Program
Erase Suspend
Read
Erase
Suspend
Program
Erase
Resume
Erase Suspend
Read
Erase
Erase
Complete
DQ6
DQ2
Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle
DQ2 and DQ6.
Figure 22.
December 14, 2005
DQ2 vs. DQ6
Am29LV640MH/L
51
D A T A S H E E T
AC CHARACTERISTICS
Temporary Sector Unprotect
Parameter
JEDEC
Std
tVIDR
tRSP
Description
VID Rise and Fall Time (See Note)
RESET# Setup Time for Temporary Sector
Unprotect
Min
All Speed Options
500
Unit
ns
Min
4
µs
Notes:
1. Not 100% tested.
2. AC Specifications listed are tested with VIO = VCC. Contact AMD for information on AC operation with VIO ≠ VCC.
VID
RESET#
VID
VSS, VIL,
or VIH
VSS, VIL,
or VIH
tVIDR
tVIDR
Program or Erase Command Sequence
CE#
WE#
tRRB
tRSP
RY/BY#
Figure 23.
52
Temporary Sector Group Unprotect Timing Diagram
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
AC CHARACTERISTICS
VID
VIH
RESET#
SA, A6,
A3, A2,
A1, A0
Valid*
Valid*
Sector Group Protect or Unprotect
Data
60h
60h
Valid*
Verify
40h
Status
Sector Group Protect: 150 µs,
Sector Group Unprotect: 15 ms
1 µs
CE#
WE#
OE#
Note: For sector group protect, A6:A0 = 0xx0010. For sector group unprotect, A6:A0 = 1xx0010.N
Figure 24.
December 14, 2005
Sector Group Protect and Unprotect Timing Diagram
Am29LV640MH/L
53
D A T A S H E E T
AC CHARACTERISTICS
Alternate CE# Controlled Erase and Program Operations
Parameter
JEDEC
tAVAV
tAVWL
tELAX
tDVEH
tEHDX
Std.
tWC
tAS
tAH
tDS
tDH
tGHEL
tGHEL
tWLEL
tEHWH
tELEH
tEHEL
tWS
tWH
tCP
tCPH
tWHWH1
tWHWH2
tWHWH1
tWHWH2
tRH
tPOLL
Description
Write Cycle Time (Note 1)
Address Setup Time
Address Hold Time
Data Setup Time
Data Hold Time
Read Recovery Time Before Write
(OE# High to WE# Low)
WE# Setup Time
WE# Hold Time
CE# Pulse Width
CE# Pulse Width High
Write Buffer Program Operation (Notes 2, 3)
Per Byte
Effective Write Buffer Program
Operation (Notes 2, 4)
Per Word
Per Byte
Accelerated Effective Write Buffer
Program Operation (Notes 2, 4)
Per Word
Byte
Single Word/Byte Program
Operation (Note 2, 5)
Word
Single Word/Byte Accelerated
Byte
Programming Operation (Note 2,
Word
5)
Sector Erase Operation (Note 7)
RESET# High Time Before Write
Program Valid Before Status Polling (Note 7)
Min
Min
Min
Min
Min
Speed Options
101, 112, 120,
90R 101R 112R 120R
90
100
110
120
0
45
45
0
Unit
ns
ns
ns
ns
ns
Min
0
ns
Min
Min
Min
Min
Typ
Typ
Typ
Typ
Typ
0
0
45
30
352
11
22
8.8
17.6
100
100
90
ns
ns
ns
ns
µs
µs
µs
µs
µs
µs
µs
µs
90
µs
0.5
50
4
sec
ns
µs
Typ
Typ
Typ
Min
Max
Notes:
1. Not 100% tested.
2. See the “Erase and Programming Performance” section for
more information.
3. For 1–16 words/1–32 bytes programmed.
4. Effective write buffer specification is based upon a
16-word/32-byte write buffer operation.
5. Word/Byte programming specification is based upon a
single word/byte programming operation not utilizing the
write buffer.
54
6. AC Specifications listed are tested with VIO = VCC. Contact
AMD for information on AC operation with VIO ≠ VCC.
7. When using the program suspend/resume feature, if the
suspend command is issued within tPOLL, tPOLL must be fully
re-applied upon resuming the programming operation. If the
suspend command is issued after tPOLL, tPOLL is not
required again prior to reading the status bits upon
resuming.
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
AC Characteristics
555 for program
2AA for erase
PA for program
SA for sector erase
555 for chip erase
Data# Polling
Addresses
PA
tWC
tAS
tAH
tWH
WE#
tPOLL
tGHEL
OE#
tWHWH1 or 2
tCP
CE#
tWS
tCPH
tBUSY
tDS
tDH
DQ7#,
DQ15
Data
tRH
A0 for program
55 for erase
DOUT
PD for program
30 for sector erase
10 for chip erase
RESET#
RY/BY#
Notes:
1. Figure indicates last two bus cycles of a program or erase operation.
2. PA = program address, SA = sector address, PD = program
data.
4. Illustration shows device in word mode.
Figure 25.
December 14, 2005
3. DQ7# is the complement of the data written to the device.
DOUT is the data written to the device.
Alternate CE# Controlled Write (Erase/Program)
Operation Timings
Am29LV640MH/L
55
D A T A S H E E T
ERASE AND PROGRAMMING PERFORMANCE
Parameter
Sector Erase Time
Typ (Note 1)
0.5
Max (Note 2)
15
Unit
sec
64
128
sec
100
100
90
90
352
11
22
800
800
720
720
1800
57
113
µs
µs
µs
µs
µs
µs
µs
282
1560
µs
8.8
17.6
92
49
98
170
µs
µs
sec
Chip Erase Time
Single Word/Byte Program Time (Note 3)
Accelerated Single Word/Byte Program Time
(Note 3)
Byte
Word
Byte
Word
Total Write Buffer Program Time (Note 4)
Effective Write Buffer Program Time (Note 5)
Per Byte
Per Word
Total Accelerated Effective Write Buffer
Program Time (Note 4)
Effective Accelerated Write Buffer Program
Time (Note 4)
Per Byte
Per Word
Chip Program Time, using the Write Buffer
Notes:
1. Typical program and erase times assume the following
conditions: 25°C, 3.0 V VCC. Programming specifications
assume that all bits are programmed to 00h.
2. Maximum values are measured at VCC = 3.0 V, worst case
temperature. Maximum values are valid up to and including
100,000 program/erase cycles.
3. Word/Byte programming specification is based upon a
single word/byte programming operation not utilizing the
write buffer.
4. For 1-16 words or 1-32 bytes programmed in a single write
buffer programming operation.
Comments
Excludes 00h
programming prior to
erasure (Note 6)
Excludes system level
overhead (Note 7)
5. Effective write buffer specification is calculated on a
per-word/per-byte basis for a 16-word/32-byte write buffer
operation.
6. In the pre-programming step of the Embedded Erase
algorithm, all bits are programmed to 00h before erasure.
7. System-level overhead is the time required to execute the
command sequence(s) for the program command. See
Tables 8 and 9 for further information on command
definitions.
8. The device has a minimum erase and program cycle
endurance of 100,000 cycles.
LATCHUP CHARACTERISTICS
Description
Input voltage with respect to VSS on all pins except I/O pins
(including A9, OE#, and RESET#)
Input voltage with respect to VSS on all I/O pins
VCC Current
Min
Max
–1.0 V
12.5 V
–1.0 V
–100 mA
VCC + 1.0 V
+100 mA
Note: Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time.
TSOP PIN AND BGA PACKAGE CAPACITANCE
Parameter Symbol
Parameter Description
Test Setup
CIN
Input Capacitance
VIN = 0
COUT
Output Capacitance
VOUT = 0
CIN2
Control Pin Capacitance
VIN = 0
TSOP
Fine-pitch BGA
TSOP
Fine-pitch BGA
TSOP
Fine-pitch BGA
Typ
6
4.2
8.5
5.4
7.5
3.9
Max
7.5
5.0
12
6.5
9
4.7
Unit
pF
pF
pF
pF
pF
pF
Notes:
1. Sampled, not 100% tested.
2. Test conditions TA = 25°C, f = 1.0 MHz.
DATA RETENTION
Parameter Description
Test Conditions
150°C
125°C
Minimum Pattern Data Retention Time
56
Am29LV640MH/L
Min
10
20
Unit
Years
Years
December 14, 2005
D A T A S H E E T
PHYSICAL DIMENSIONS
TS056/TSR056—56-Pin Standard and Reverse Pinout
Thin Small Outline Package (TSOP)
PACKAGE
TS/TSR 56
JEDEC
MO-142 (B) EC
SYMBOL
NOTES:
MIN.
NOM.
MAX.
1
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (mm).
(DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982.)
A
---
---
1.20
2
PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP).
A1
0.05
---
0.15
3
PIN 1 IDENTIFIER FOR REVERSE PIN OUT (DIE DOWN), INK OR LASER MARK.
A2
0.95
1.00
1.05
4
b1
0.17
0.20
0.23
b
c1
0.17
0.10
0.22
---
0.27
0.16
TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS
DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE
LEADS ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE.
5
DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE
MOLD PROTUSION IS 0.15 mm PER SIDE.
6
DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE
DAMBAR PROTUSION SHALL BE 0.08 mm TOTAL IN EXCESS OF b
DIMENSION AT MAX MATERIAL CONDITION. MINIMUM SPACE BETWEEN
PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 mm.
7
THESE DIMESIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN
0.10 mm AND 0.25 mm FROM THE LEAD TIP.
8.
LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED FROM THE
SEATING PLANE.
9
DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS.
c
0.10
---
0.21
D
19.90
20.00
20.20
D1
18.30
18.40
18.50
E
13.90
14.00
14.10
0.50 BASIC
e
L
0.50
0.60
0.70
O
0˚
3˚
5˚
R
0.08
---
0.20
N
December 14, 2005
56
3160\38.10A
Am29LV640MH/L
57
D A T A S H E E T
PHYSICAL DIMENSIONS
LAA064—64-Ball Fortified Ball Grid Array (FBGA) 13 x 11 mm Package
58
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
REVISION SUMMARY
Revision A (March 19, 2002)
Revision D+1 (September 10, 2002)
Initial release as abbreviated Advance Information
data sheet. This document contains information that
was previously released in publication number 25301.
Product Selector Guide
Added Note 2.
Ordering Information
Ordering Information
Added Note 1.
The package marking for the Fortified BGA option has
been updated.
Sector Erase Command Sequence
Physical Dimensions
Deleted statement that describes the outcome of
when the Embedded Erase operation is in progress.
Added drawing that shows both TS056 and TSR056
specifications.
Revision E (December 5, 2002)
Revision B (April 26, 2002)
Product Selector Guide and Read-Only
Characteristics
Expanded data sheet to full specification version.
Revision C (May 23, 2002)
Changed packaging from 63-ball FBGA to 64-ball Fortified BGA. Changed Block Diagram: Moved VIO from
RY/BY# to Input/Output Buffers. Changed note about
WP#/ACC pin to indicate internal pullup to VCC. Modified Table 4: Sector Group Protection/Unprotection Address Table. Changed 47h Address data from 0004h
to 0001h in Table 9.
Added a 30 ns option to tPACC and tOE standard for the
112R and 120R speed options.
Customer Lockable: SecSi Sector NOT
Programmed or Protected at the factory.
Added second bullet, SecSi sector-protect verify text
and figure 3.
SecSi Sector Flash Memory Region, and Enter
SecSi Sector/Exit SecSi Sector Command
Sequence
Noted that the ACC function and unlock bypass modes
are not available when the SecSi sector is enabled.
Revision D (August 8, 2002)
Alternate CE# Controlled Erase and Program
Operations
Added tRH parameter to table.
Erase and Program Operations
Byte/Word Program Command Sequence, Sector
Erase Command Sequence, and Chip Erase Command Sequence
Noted that the SecSi Sector, autoselect, and CFI
functions are unavailable when a program or erase
operation is in progress.
Added tBUSY parameter to table.
TSOP and BGA PIN Capacitance
Common Flash Memory Interface (CFI)
Added the FBGA package.
Program Suspend/Program Resume Command
Sequence
Changed CFI website address
Figure 6. Program Suspend/Program Resume
Changed 15 μs typical to maximum and added 5 μs
typical.
Change wait time to 15 μs.
Erase Suspend/Erase Resume Commands
Added ILR row to table. Changed VIH1 and VIH2 minimum to 1.9. Removed typos in notes.
Changed typical from 20 μs to 5 μs and added a maximum of 20 μs.
Special package handling instructions
Modified the special handling wording.
DC Characteristics table
CMOS Compatible
Hardware Reset, CMOS Tables, Erase and Program
Operations, Temporary Sector Unprotect, and
Alternate CE# Controlled Erase and Program
Operations
Added Note.
Deleted the Iacc specification row.
Revision E+1 (February 16, 2003)
CFI
Changed text in the third paragraph of CFI to read
“reading array data.”
December 14, 2005
Distinctive Characteristics
Corrected performance characteristics.
Am29LV640MH/L
59
D A T A S H E E T
Product Selector Guide
DC Characteristics table
Added note 2.
Corrected note reference number on VOL specification.
Ordering Information
Hardware Reset (RESET#)
Corrected Valid Combinations table.
Added tRB specification to table.
Added Note.
Revision F+1 (February 17, 2004)
AC Characteristics
Erase Suspend/Erase Resume Commands
Removed 90, 90R speed option. Added Note
Input values in the tWHWH1 and tWHWH2 parameters in
the Erase and Program Options table that were previously TBD. Also, added note 5.
Input values in the tWHWH1 and tWHWH2 parameters in
the Alternate CE# Controlled Erase and Program Options table that were previously TBD. Also, added note
5.
Erase and Programming Performance
Input values into table that were previously TBD.
Added notes 3 and 4.
Added note (last paragraph) in reference to erase operation.
AC Characteristics - Erase and Program
Operations, and Alternate CE# Controlled Erase
and Program Operations
Added tPOLL information.
AC Characteristics - Program Operation Timings,
Data# Polling Timings, and Alternate CE#
Controlled Write (Erase/Program) Operation
Timings
Updated figures to show tPOLL information.
Revision E+2 (June 11, 2003)
Trademarks
Ordering Information
Updated.
Added 90R speed grade, modified note.
Revision F+2 (August 23, 2004)
Erase and Programming Performance
Added Max programming specifications.
Modified table, supplied values for Typical.
Added notation referencing superseding documentation.
Revision F (August 14, 2003)
Global
Revision F+3 (December 14, 2005)
Converted document to new Spansion template.
Global
Ordering Information
This product has been retired and is not available for
designs. For new and current designs, S29GL064A
supersedes Am29LV640M H/L and is the factory-recommended migration path. Please refer to the
S29GL064A datasheet for specifications and ordering
information. Availability of this document is retained for
reference and historical purposes only.
Added note for ordering and marking information related to “N” (factory-protected SecSi Sector) devices.
Command Definitions
Corrected Program Erase/Suspend addressing from
BA to don’t care.
Trademarks
Copyright © 2002-2005 Advanced Micro Devices, Inc. All rights reserved.
AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc.
ExpressFlash is a trademark of Advanced Micro Devices, Inc.
Product names used in this publication are for identification purposes only and may be trademarks of their respective companies.
60
Am29LV640MH/L
December 14, 2005
Similar pages