HMC483MS8G / 483MS8GE v01.0710 MIXERS - HIGH IP3 - SMT 10 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz Typical Applications Features The HMC483MS8G / HMC483MS8GE is ideal for: +33 dBm Input IP3 • Cellular/3G Conversion Loss: 9 dB • GSM, GPRS & EDGE Low LO Drive: -4 to +4 dBm • CDMA & WCDMA Single Positive Supply: 5V @ 50 mA • Cable Modem Termination Systems Ultra Small MSOP Package: 14.8mm2 Included in the HMC-DK003 Designer’s Kit Functional Diagram General Description The HMC483MS8G & HMC483MS8GE are high dynamic range passive MMIC mixers with integrated LO amplifiers in plastic surface mount 8 lead Mini Small Outline Packages (MSOP) covering 0.7 to 1.5 GHz. Excellent input IP3 performance of +33 dBm for down conversion and +30 dBm for up conversion is provided for 2.5G & 3G GSM/CDMA applications at an LO drive of 0 dBm. With an input 1 dB compression of +24 dBm, the RF port will accept a wide range of input signal levels. Conversion loss is 9 dB typical. The DC to 350 MHz IF frequency response will satisfy GSM/CDMA transmit or receive frequency plans configured for low side LO. The HMC483MS8G(E) are pin for pin compatible with the HMC485MS8G(E) which are 1.7 - 2.2 GHz mixers with LO amplifiers. Electrical Specifi cations, TA = +25°C, LO = 0 dBm, IF = 70 MHz*, Vdd= 5V Parameter Min. Typ. Frequency Range, RF & LO 0.8 - 1.1 Frequency Range, IF DC - 350 Max. Min. Typ. Max. 0.7 - 1.5 Units GHz DC - 350 MHz Conversion Loss 8.5 10.5 9 12 dB Noise Figure (SSB) 8.5 10.5 9 12 dB LO to RF Isolation 10 20 6 14 LO to IF Isolation 6 10 6 13 dB dB IP3 (Input) 33 33 dBm 1 dB Gain Compression (Input) 24 23 dBm -4 to +4 -4 to +4 dBm 50 50 mA LO Input Drive Level (Typical) Supply Current *Unless otherwise noted, all measurements performed as a downconverter. 10 - 230 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC483MS8G / 483MS8GE v01.0710 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz Isolation 0 0 -5 -10 -10 + 25C + 85C - 40C -15 0.7 0.8 0.9 1 1.1 1.2 RF TO IF LO TO RF LO TO IF -30 -40 0.6 -20 0.6 10 -20 1.3 1.4 1.5 0.7 0.8 0 -5 -5 RETURN LOSS (dB) CONVERSION GAIN (dB) 0 -10 -20 0.6 LO = -6 dBm LO = -4 dBm LO = -2 dBm LO = 0 dBm LO = +2 dBm LO = +4 dBm 1.2 1.3 1.4 1.5 -15 LO RF -20 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 Upconverter Performance Conversion Gain 0.6 0.7 0.8 0 0 -5 -5 -10 LO = -6 dBm LO = -4 dBm LO = -2 dBm LO = 0 dBm LO = +2 dBm LO = +4 dBm -15 0.9 1 1.1 1.2 FREQUENCY (GHz) 1.3 1.4 1.5 IF Bandwidth RESPONSE (dB) CONVERSION GAIN (dB) 1.1 -10 RF FREQUENCY (GHz) -20 0.6 1 Return Loss Conversion Gain vs. LO Drive -15 0.9 FREQUENCY (GHz) RF FREQUENCY (GHz) MIXERS - HIGH IP3 - SMT ISOLATION (dB) CONVERSION GAIN (dB) Conversion Gain vs. Temperature CONVERSION GAIN RETURN LOSS -10 -15 -20 0.7 0.8 0.9 1 1.1 1.2 RF FREQUENCY (GHz) 1.3 1.4 1.5 0 80 160 240 320 400 IF FREQUENCY (MHz) *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 70 MHz. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10 - 231 HMC483MS8G / 483MS8GE v01.0710 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz Input IP3 vs. LO Drive 40 35 35 INPUT IP3 (dBm) 40 30 + 25C + 85C - 40C 25 0.6 0.8 0.9 1 1.1 1.2 FREQUENCY (GHz) 1.3 1.4 1.5 Input IP2 vs. Temperature 0.6 35 35 INPUT IP2 (dBm) 40 30 0.6 + 25C + 85C - 40C 0.8 0.9 1 1.1 1.2 FREQUENCY (GHz) 1.3 1.4 1.5 1.3 1.4 1.5 1.4 1.5 30 LO =-6dBm LO =-4dBm LO =-2dBm LO = 0dBm LO =+2dBm LO =+4dBm 25 20 0.7 0.8 0.9 1 1.1 1.2 FREQUENCY (GHz) 1.3 1.4 1.5 Input P1dB vs. Temperature 0.6 25 30 INPUT IP3 (dBm) 40 20 + 25C + 85C - 40C 15 0.7 0.8 0.9 1 1.1 1.2 FREQUENCY (GHz) Upconverter IP3 vs. LO Drive 30 10 0.6 0.7 Input IP2 vs. LO Drive 40 25 INPUT P1dB (dBm) LO =-6dBm LO =-4dBm LO =-2dBm LO = 0dBm LO =+2dBm LO =+4dBm 20 0.7 20 10 - 232 30 25 20 INPUT IP2 (dBm) MIXERS - HIGH IP3 - SMT 10 INPUT IP3 (dBm) Input IP3 vs. Temperature 20 LO =-6dBm LO =-4dBm LO =-2dBm LO = 0dBm LO =+2dBm LO =+4dBm 10 0 0.7 0.8 0.9 1 1.1 1.2 FREQUENCY (GHz) 1.3 1.4 1.5 0.7 0.8 0.9 1 1.1 1.2 1.3 RF FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC483MS8G / 483MS8GE v01.0710 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz MxN Spurious Outputs Harmonics of LO nLO Spur at RF Port 0 1 2 3 4 LO Freq GHz 1 2 3 4 0 xx -9 24 3 16 0.7 21 23 24 25 1 4 0 30 15 28 0.8 15 23 18 43 2 66 71 50 61 61 0.9 12 26 23 39 3 83 95 103 89 95 1 9 22 33 32 4 106 105 103 108 108 1.1 6 22 42 27 1.2 3 21 25 26 RF Freq = 0.87 GHz @ -10 dBm LO Freq = 0.8 GHz @ 0 dBm All values in dBc Relative to the IF power level. LO power = 0 dBm All values in dBc below input LO level measured at RF port. Absolute Maximum Ratings RF/IF Input +27 dBm LO Drive +10 dBm Bias Supply (Vdd) +7 Vdc Channel Temperature 150 °C Continuous Pdiss (T = 85°C) (Derate 8.95 mW/°C above 85°C) 0.58 W Thermal Resistance (RTH) (Channel to ground paddle) 111.7 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C IF DC Current ±40 mA ESD Sensitivity (HBM) Class 1B ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 10 MIXERS - HIGH IP3 - SMT nLO mRF Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10 - 233 HMC483MS8G / 483MS8GE v01.0710 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz Package Information MIXERS - HIGH IP3 - SMT 10 10 - 234 Part Number Package Body Material Lead Finish MSL Rating HMC483MS8G Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC483MS8GE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H483 XXXX [2] H483 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX Pin Descriptions Pin Number Function Description 1 LO This pin is AC coupled and matched to 50 Ohms. 2 N/C Not connected. This pin may be connected to RF/DC ground without affecting performance. 3, 6, 7 GND This pin and the ground paddle must be connected to RF ground. 4 Vdd Power supply for LO amplifier. An external RF bypass capacitor is required. 5 IF This pin is DC coupled. For applications not requiring operation to DC this port should be DC blocked externally using a series capacitor. Choose value of capacitor to pass IF frequency desired. For operation to DC, this pin must not sink/source more than 40 mA of current or failure may result. 8 RF This pin is DC coupled and matched to 50 Ohms. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC483MS8G / 483MS8GE v01.0710 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz Evaluation PCB MIXERS - HIGH IP3 - SMT 10 List of Materials for Evaluation PCB 105188 [1] Item Description J1 - J3 PCB Mount SMA RF Connector J4 - J5 DC Pin C1 10,000 pF Chip Capacitor, 0603 Pkg. U1 HMC483MS8G / HMC483MS8GE Mixer PCB [2] 104813 Evaluation Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10 - 235