power light source TM Luxeon V Emitter Technical Data DS34 LuxeonTM is a revolutionary, energy efficient and ultra compact new light source, combining the lifetime and reliability advantages of Light Emitting Diodes with the brightness of conventional lighting. Features • Highest Flux per LED in the world – 4X the Flux of a comparable Luxeon and up to 50X the Flux of standard through hole LEDs • Extreme Luminous Density – 20X the Luxeon Emitters give you total design freedom and unmatched brightness, creating a new world of light. lm/mm2 of a standard through hole LED • Very long operating life (up to100k hours) • Available in Green, Blue, Royal Blue and Cyan The Luxeon V offers extreme luminous density, providing lumens per • Lambertian or Side Emitting radiation pattern package of 4X a Luxeon or up to 50X that of alternative solid state light • More Energy Efficient than Incandescent and sources creating new opportunities for solid state lighting to displace conventional lighting technologies. most Halogen lamps • Low voltage DC operated • Cool beam, safe to the touch • Instant light (less than 100 ns) Luxeon V Emitters can be purchased in reels for high volume assembly. For high volume applications, custom Luxeon power light source designs are • Fully dimmable • No UV • Superior ESD protection available upon request, to meet your specific needs. Typical Applications • Portable (flashlight, bicycle) • Architectural Detail Lighting • Decorative • Fiber Optic Alternative M Emitters can be purchased i reels for high volume assembly. Sample kits are also available for prototyping and design evaluation. A sample kits contains • Medical Applications • Power Signaling / Airfield / Taxiway Lighting • Edge-Lit Signs (Exit, Point Of Sale) • LCD Backlights / Light Guides a strip of 50 taped Luxeon V Emitter is available in green, blue, royal blue and cyan. Mechanical Dimensions Lambertian Notes: 1. 2. 3. 4. The anode side of the device is denoted by a hole in the lead frame. Electrical insulation between the case and the board is required – slug of device is not electrically neutral. Do not electrically connect either the anode or cathode to the slug. Drawings not to scale. All dimensions are in millimeters. All dimensions without tolerances are for reference only. Side Emitting Notes: 1. 2. 3. 4. 5. Luxeon V Emitter 2 Document #: DS34 (09/19/04) The anode side of the device is denoted by a hole in the lead frame. Electrical insulation between the case and the board is required – slug of device is not electrically neutral. Do not electrically connect either the anode or cathode to the slug. Caution must be used in handling this device to avoid damage to the lens surfaces that will reduce optical efficiency. Drawings not to scale. All dimensions are in millimeters. All dimensions without tolerances are for reference only. Notes: Flux Characteristics at 700mA, Junction Temperature, TJ = 25oC 1. Color Luxeon V Emitter Minimum Luminous Flux (lm) or Radiometric Power (mW) ΦV [1,2] Green Cyan Blue[3] Royal blue[4] LXHL-PM02 LXHL-PE02 LXHL-PB02 LXHL-PR02 67.2 67.2 23.5 275 mW 160 160 48 700 mW Green Cyan Blue[3] Royal Blue[4] LXHL-DM02 LXHL-DE02 LXHL-DB02 LXHL-DR02 67.2 67.2 23.5 275 mW 145 145 43 630 mW Typical Luminous Flux (lm) or Radiometric Power (mW) ΦV [2] 2. Radiation Pattern Lambertian 3. Side Emitting 4. Minimum luminous flux or radiometric power performance guaranteed within published operating conditions. Lumileds maintains a tolerance of ± 10% on flux and power measurements. Luxeon types with even higher luminous flux levels will become available in the future. Please consult your Lumileds Authorized Distributor or Lumileds sales representative for more information. Minimum flux value for 470 nm devices. Due to the CIE eye response curve in the short blue wavelength range, the minimum luminous flux will vary over the Lumileds’ blue color range. Luminous flux will vary from a minimum of 18.1 lm at 460 nm to a typical of 80 lm at 480 nm due to this effect. Although the luminous power efficiency is lower in the short blue wavelength range, radiometric power efficiency increases as wavelength decreases. For more information, consult the Luxeon Design Guide, available upon request. Royal Blue product is binned by radiometric power and peak wavelength rather than photometric lumens and dominant wavelength. Electrical Characteristics at 700mA, Junction Temperature, TJ = 25oC Notes: Temperature Color Green Cyan Blue Royal Blue Dynamic resistance[2] (Ω) RD Forward Voltage VF (V)[1] Min. Typ. Max. 5.43 5.43 5.43 5.43 Luxeon V Emitter 6.84 6.84 6.84 6.84 8.31 8.31 8.31 8.31 1.0 1.0 1.0 1.0 3 coefficient of forward voltage[3] (mV/oC) ∆VF/ ∆TJ -4.0 -4.0 -4.0 -4.0 Thermal resistance, junction to case (oC/W) RθJ-C 8 8 8 8 Document #: DS34 (09/19/04) 1. 2. 3. Lumileds maintains a tolerance of ± 0.06V on forward voltage measurements. Dynamic resistance is the inverse of the slope in linear forward voltage model for LEDs. See Figure 3. Measured between 25oC ≤ TJ ≤ 110oC at IF = 700mA. Notes: (for both optical tables) Optical Characteristics at 700mA, Junction Temperature, TJ = 25oC 1. temp Radiation Pattern Lambertian Color Green Cyan Blue royal blue[2] Dominant Wavelength[1] λD or Peak Wavelength[2] λP Min. Typ. Max. Spectral Halfwidth[3] (nm) ∆λ1/2 coefficient of dominant Total Included (nm/oC) ∆λD/ ∆ΤJ Angle[4] Viewing Angle[5] (degrees) (Degrees) θ0.90V 2θ 1/2 wavelength 520 nm 490 nm 460 nm 530 nm 505 nm 470 nm 550 nm 520 nm 490 nm 35 30 25 0.04 0.04 0.04 150 150 150 150 150 150 440 nm 455 nm 460 nm 20 0.04 150 150 2. 3. 4. 5. Optical Characteristics at 700mA, Junction Temperature, TJ = 25oC, Continued (nm/oC) ∆λD/ ∆ΤJ Typical total flux percent within first 45°[6] Cum Φ45° Typical Angle of off axis peak intensity[7] θPEAK temp Spectral Dominant Wavelength λD or Peak Wavelength[2] λP Min. Typ. Max. [1] Radiation Pattern Color Green Cyan Side Emitting Blue royal blue[2] Halfwidth[3] (nm) ∆λ1/2 coefficient of dominant wavelength 520 nm 490 nm 460 nm 530 nm 505 nm 470 nm 550 nm 520 nm 490 nm 35 30 25 0.04 0.04 0.04 <30% <30% <30% 75° - 85° 75° - 85° 75° - 85° 440 nm 455 nm 460 nm 20 0.04 <30% 75° - 85° 6. 7. 8. 9. Dominant wavelength is derived from the CIE 1931 Chromaticity diagram and represents the perceived color. Lumileds maintains a tolerance of ± 0.5nm for dominant wavelength measurements. Royal Blue product is binned by radiometric power and peak wavelength rather than photometric lumens and dominant wavelength. Lumileds maintains a tolerance of ± 2nm for peak wavelength measurements. Spectral width at ½ of the peak intensity. Total angle at which 90% of total luminous flux is captured. θ½ is the off axis angle from lamp centerline where the luminous intensity is ½ of the peak value. Cumulative flux percent within ± 45° from optical axis. Off axis angle from lamp centerline where the luminous intensity reaches peak off axis value. On axis peak may be higher than off axis peak. All products built with Indium Gallium Nitride (InGaN). Blue and Royal Blue power light sources represented here are IEC825 Class 2 for eye safety. Notes: 1. Absolute Maximum Ratings Green/Cyan/ Blue/Royal Blue Parameter DC Forward Current (mA) [1] Peak Pulsed Forward Current (mA) Average Forward Current (mA) ESD Sensitivity [2] LED Junction Temperature (oC) Storage Temperature (oC) Soldering Temperature (oC) [3] Luxeon V Emitter 700 1000 700 ± 16,000V HBM 135 -40 to +120 260 for 5 seconds max 4 Document #: DS34 (09/19/04) 2. 3. Proper current derating must be observed to maintain junction temperature below the maximum. For more information, consult the Luxeon Design Guide, available upon request. LEDs are not designed to be driven in reverse bias. Please consult Lumileds’ Application Brief AB11 for further information. Measured at leads, during lead soldering and slug attach, body temperature must not exceed 120oC. Luxeon emitters cannot be soldered by general IR or Vapor-phase reflow, nor by wave soldering. Lead soldering is limited to selective heating of the leads, such as by hot-bar reflow, fiber focussed IR, or hand soldering. The package back plane (slug) may not be attached by soldering, but rather with a thermally conductive adhesive. Electrical insulation between the slug and the board is required. Please consult Lumileds’ Application Brief AB10 on Luxeon Emitter Assembly Information for further details on assembly methods. Relative Spectral Power Distribution Wavelength Characteristics, TJ = 25oC 1.0 0.8 0.6 BLUE GREEN ROYAL BLUE CYAN 0.4 Figure 1. Relative Intensity vs. Wavelength. 0.2 0.0 400 450 500 550 600 650 700 Wavelength (nm) Relative Light Output (%) Light Output Characteristics 150 140 130 120 110 100 90 80 70 60 50 -20 Green P ho to metric Cyan P ho to metric B lue P ho to metric Ro yal B lue Radio metric Figure 2. Relative Light Output vs. Junction Temperature. 0 20 40 60 80 100 120 Junction Temperature, TJ ( C) o Luxeon V Emitter 5 Document #: DS34 (09/19/04) Forward Current Characteristics, TJ = 25oC Note: IF - Average Forward Current (mA) Driving these high power devices at currents less than the test conditions may produce unpredictable results and may be subject to variation in performance. Pulse width modulation (PWM) is recommended for dimming effects. 800 700 600 500 400 300 200 Figure 3. Forward Current vs. Forward Voltage. 100 0 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 V F - Forw ard Voltage (Volts) Normalized Relative Luminous Flux 1.2 1 0.8 0.6 0.4 Figure 4. Relative Luminous Flux vs. Forward Current at TJ = 25oC maintained. 0.2 0 0 200 100 400 200 600 300 800 400 IF - Average Forw ard Current (mA) Note: Driving these high power devices at currents less than the test conditions may produce unpredictable results and may be subject to variation in performance. Pulse width modulation is recommended for dimming effects. Luxeon V Emitter 6 Document #: DS34 (09/19/04) Current Derating Curve Note: Additional heatsinking is required, even for extremely brief periods. Please consult AB05, Luxeon Thermal Design Guide, for additional information. IF - Forward Current (mA) 800 700 600 500 400 300 200 R θ J-A=20oC/W R θ J-A=15oC/W R θ J-A=10oC/W Figure 5. Maximum Forward Current vs. Ambient Temperature. Derating based on TJMAX = 135 oC. 100 0 0 25 50 75 100 125 150 ο TA - Am bient Tem perature ( C) Representative Typical Spatial Radiation Pattern Lambertian Radiation Pattern 100 90 80 70 60 50 40 30 20 10 0 -100 -80 -60 Figure 6. Representative Typical Spatial Radiation Pattern for Luxeon V Emitter. Typical Upper Bound Typical Lower Bound -40 -20 0 20 40 60 80 100 Angular Displacement (Degrees) Side Emitting Radiation Pattern 100 Relative Intensity (%) 90 80 70 60 50 40 Figure 7. Representative Typical Spatial Radiation Pattern for Luxeon V Emitter. 30 20 10 0 -120 -100 -80 -60 -40 -20 0 20 40 60 80 100 120 Angular Displacement (Degrees) Luxeon V Emitter 7 Document #: DS34 (09/19/04) Emitter Reel Packaging Figure 8. Reel dimensions and orientation. Figure 9. Tape dimensions for Lambertian and Side Emitting radiation patterns. Notes: 1. 2. 3. 4. Lambertian Side Emitting Luxeon V Emitter 2 Document #: DS34 (09/19/04) Luxeon emitters should be picked up by the body (not the lens) during placement. The inner diameter of the pick-up collet should be greater than or equal to 6.5 mm. Please consult Lumileds' Application Brief AB10 on Luxeon Emitter assembly information for further details on assembly methods. Drawings not to scale. All dimensions are in millimeters. All dimensions without tolerances are for reference only. About Luxeon Luxeon is the new world of solid state lighting (LED) technology. Luxeon Power Light Source Solutions offer huge advantages over conventional lighting and huge advantages over other LED solutions. Luxeon enables partners to create and market products that, until now, were impossible to create. This means the opportunity to create products with a clear competitive advantage in the market. Products that are smaller, lighter, sleeker, cooler, and brighter. Products that are more fun to use, more efficient, and more environmentally conscious than ever before possible! Company Information Luxeon is developed, manufactured and marketed by Lumileds Lighting, LLC. Lumileds is a worldclass supplier of Light Emitting Diodes (LEDs) producing billions of LEDs annually. Lumileds is a fully integrated supplier, producing core LED material in all three base colors (Red, Green, Blue) and White. Lumileds has R&D development centers in San Jose, California and Best, The Netherlands. Production capabilities in San Jose, California and Malaysia. Lumileds is pioneering the highflux LED technology and bridging the gap between solid state LED technology and the lighting world. Lumileds is absolutely dedicated to bringing the best and brightest LED technology to enable new applications and markets in the Lighting world. Lumileds may make process or materials changes affecting the performance or other characteristics of Luxeon. These products supplied after such change will continue to meet published specifications, but may not be identical to products supplied as samples or under prior orders. LUMILEDS www.luxeon.com www.lumileds.com For technical assistance or the location of your nearest Lumileds sales office, call: Worldwide: +1 408-435-6044 US Toll free: 877-298-9455 Europe: +31 499 339 439 Asia: +65 6248 4759 Japan: +81 (426) 60 8532 Fax: 408-435-6855 Email us at [email protected] 2003 Lumileds Lighting U.S. LLC. All rights reserved. Lumileds Lighting is a joint venture between Agilent Technologies and Philips Lighting. Luxeon is a trademark of Lumileds Lighting, Inc. Product specifications are subject to change without notice. Luxeon V Emitter 3 Document #: DS34 (09/19/04) Lumileds Lighting, LLC 370 West Trimble Road San Jose, CA 95131