Hittite HMC274QS16E 1 db lsb gaas ic 5-bit digital attenuator, 0.7 - 2.7 ghz Datasheet

HMC274QS16 / 274QS16E
v01.0505
ATTENUATORS - SMT
5
1 dB LSB GaAs IC 5-BIT DIGITAL
ATTENUATOR, 0.7 - 2.7 GHz
Typical Applications
Features
The HMC274QS16 / HMC274QS16E is ideal for:
1 dB LSB Steps to 31 dB
• Cellular/PCS/3G Infrastructure
Single Positive Control (+3 to +5V) Per Bit
• 2.4 GHz ISM Radios
±0.5 dB Typical Bit Error
• Wireless Data
Small QSOP16 Plastic Package
Included in the HMC-DK004 Designer’s Kit
Functional Diagram
General Description
The HMC274QS16 & HMC274QS16E are broadband
5-bit positive control GaAs IC digital attenuators in
16 lead QSOP plastic packages. Covering 0.7 to 2.7
GHz the insertion loss is typically less than 2.3 dB.
The attenuator bit values are 1 (LSB), 2, 4, 8, and
16 dB for a total attenuation of 31 dB. Accuracy
is excellent at ± 0.5 dB typical with an IIP3 of up to
+50 dBm. Five bit control voltage inputs, toggled
between 0 and +3 to +5 volts, are used to select
each attenuation state. A single Vdd bias of +3 to +5
volts applied through an external 5K Ohm resistor is
required.
Electrical Specifi cations, TA = +25° C, Vdd = +3V to +5V & Vctl = 0/Vdd
Parameter
Frequency
Insertion Loss
0.7 - 1.4 GHz
1.4 - 2.3 GHz
2.3 - 2.7 GHz
Attenuation Range
0.7 - 2.7 GHz
Return Loss (RF1 & RF2, All Atten. States)
0.7 - 1.4 GHz
1.4 - 2.7 GHz
Min.
Typical
Max.
Units
2.0
2.3
2.5
2.4
2.7
3.1
dB
dB
dB
31
dB
15
17
dB
dB
0.7 - 1.4 GHz
1.4 - 2.3 GHz
2.3 - 2.7 GHz
± 0.35 + 5% of Atten. Setting Max
± 0.25 + 3% of Atten. Setting Max
± 0.30 + 5% of Atten. Setting Max
dB
dB
dB
10
12
Attenuation Accuracy: (Referenced to Insertion Loss)
All Attenuation States
All Attenuation States
All Attenuation States
Input Power for 0.1 dB Compression
Vdd = 5V
Vdd = 3V
0.7 - 2.7 GHz
29
20
dBm
dBm
Input Third Order Intercept Point
(Two-tone Input Power = 0 dBm Each Tone)
Vdd = 5V
Vdd = 3V
0.7 - 2.7 GHz
54
52
dBm
dBm
560
600
ns
ns
Switching Characteristics
tRISE, tFALL (10/90% RF)
tON, tOFF (50% CTL to 10/90% RF)
5 - 28
0.7 - 2.7 GHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC274QS16 / 274QS16E
v01.0505
1 dB LSB GaAs IC 5-BIT DIGITAL
ATTENUATOR, 0.7 - 2.7 GHz
5
Return Loss RF1, RF2
Insertion Loss
(Only Major States are Shown)
-2
-3
+25 C
+85 C
-40 C
-4
-5
0.5
I.L.
1 dB
2 dB
4 dB
8 dB
16 dB
31 dB
-5
-1
1
1.5
2
-10
-15
-20
-25
2.5
-30
0.5
3
1
1.5
FREQUENCY (GHz)
2
2.5
3
FREQUENCY (GHz)
Normalized Attenuation
Bit Error vs. Attenuation State
0
1.5
-5
1
-10
BIT ERROR (dB)
NORMALIZED ATTENUATION (dB)
(Only Major States are Shown)
-15
-20
-25
-35
0.5
0.5
0
-0.5
0.9 GHz
1.9 GHz
2.4 GHz
-1
-30
-1.5
1
1.5
2
2.5
3
0
4
8
FREQUENCY (GHz)
12
16
20
Relative Phase vs. Frequency
(Only Major States are Shown)
(Only Major States are Shown)
28
32
150
RELATIVE PHASE (deg)
2
1
BIT ERROR (dB)
24
ATTENUATION STATE (dB)
Bit Error vs. Frequency
0
1 dB
2 dB
4 dB
8 dB
16 dB
31 dB
-1
-2
0.5
ATTENUATORS - SMT
0
RETURN LOSS (dB)
INSERTION LOSS (dB)
0
1
1.5
2
2.5
3
FREQUENCY (GHz)
100
1 dB
2 dB
4 dB
8 dB
16 dB
31 dB
50
0
-50
-100
0.5
1
1.5
2
2.5
3
FREQUENCY (GHz)
Note: All Data Typical Over Voltage (+3V to +5V).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 29
HMC274QS16 / 274QS16E
v01.0505
ATTENUATORS - SMT
5
1 dB LSB GaAs IC 5-BIT DIGITAL
ATTENUATOR, 0.7 - 2.7 GHz
Compression Point & IP3
Input P1dB (dBm)
Input P0.1dB (dBm)
Input IP3 (dBm)
Attenuation
State (dB)
Control
Voltage (V)
+25C
+85C
-40C
+25C
+85C
-40C
+25C
+85C
-40C
1
5
32.3
31.8
32.9
29.4
28.8
29.8
54.7
49.1
52.2
2
5
32.3
31.8
32.8
29.2
28.6
29.4
52.2
49.1
52.2
4
5
32.8
32.1
33.3
29.4
28.7
29.3
54.1
48.65
52.7
1
3
24.8
25.7
25.2
19.7
18.6
21.1
52.2
48.1
52.5
2
3
24.7
24.1
25.1
19.7
18.3
21.0
52.2
48.1
52.2
4
3
26.0
25.6
26.6
19.6
18.6
21.1
53.1
47.65
53.2
Application Circuit
DC blocking capacitors C1 & C2 are
required on RF1 & RF2. Choose C1 = C2
= 100 ~ 300 pF to allow lowest customer
specific frequency to pass with minimal
loss. R1 = 5K Ohm is required to supply
voltage to the circuit through either PIN 9
or PIN 16.
Truth Table
Control Voltage Input
V1
16 dB
V2
8 dB
V3
4 dB
V4
2 dB
V5
1 dB
Attenuation
Setting
RF1 - RF2
High
High
High
High
High
Reference I.L.
High
High
High
High
Low
1 dB
High
High
High
Low
High
2 dB
High
High
Low
High
High
4 dB
High
Low
High
High
High
8 dB
Low
High
High
High
High
16 dB
Low
Low
Low
Low
Low
31 dB Max. Atten.
Any combination of the above states will provide an attenuation approximately equal to the sum of the bits selected.
5 - 30
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC274QS16 / 274QS16E
Absolute Maximum Ratings
1 dB LSB GaAs IC 5-BIT DIGITAL
ATTENUATOR, 0.7 - 2.7 GHz
5
Control Voltages
Control Voltage (V1 - V5)
Vdd + 0.5 Vdc
State
Bias Condition
Bias Voltage (Vdd)
+8.0 Vdc
Low
0 to +0.2 V @ 20 uA Max
Storage Temperature
-65 to +150 °C
High
Vdd ± 0.2V @ 100 uA Max
Operating Temperature
-40 to +85 °C
ATTENUATORS - SMT
v01.0505
Note: Vdd = +3V to 5V ± 0.2V
RF Input Power (0.7 - 2.7 GHz)
+30 dBm
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE.
4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE.
5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC274QS16
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC274QS16E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
HMC274
XXXX
[2]
HMC274
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 31
HMC274QS16 / 274QS16E
v01.0505
1 dB LSB GaAs IC 5-BIT DIGITAL
ATTENUATOR, 0.7 - 2.7 GHz
ATTENUATORS - SMT
5
5 - 32
Pin Descriptions
Pin Number
Function
Description
1, 2, 8, 10 - 15
GND
This pin must be DC grounded.
3-7
V1 - V5
See truth table and control voltage table.
9
RF1
This pin is DC coupled and matched to 50 Ohm.
Blocking capacitors are required.
16
RF1
This pin is DC coupled and matched to 50 Ohm.
Blocking capacitors are required.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC274QS16 / 274QS16E
v01.0505
1 dB LSB GaAs IC 5-BIT DIGITAL
ATTENUATOR, 0.7 - 2.7 GHz
* R2 - R6 = 100 Ohm.
These resistors are optional
and may be used to enhance
decoupling of the RF path
from the control inputs.
ATTENUATORS - SMT
5
Evaluation PCB
List of Materials for Evaluation PCB 104976 [1]
Item
Description
J1 - J2
PCB Mount SMA Connector
J3 - J11
DC Pin
R1
5k Ohm Resistor, 0402 Chip
R2 - R6
100 Ohm Resistor, 0402 Chip
C1, C2
0402 Chip Capacitor, Select for Lowest
Frequency of Operation
U1
HMC274QS16 / HMC274QS16E
Digital Attenuator
PCB [2]
104931 Evaluation PCB
The circuit board used in the final application
should use RF circuit design techniques. Signal
lines should have 50 ohm impedance while the
package ground leads should be connected directly
to the ground plane similar to that shown below. A
sufficient number of via holes should be used to
connect the top and bottom ground planes. The
evaluation circuit board as shown is available from
Hittite Microwave Corporation upon request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 33
Similar pages