LINER LTC3891 Low iq, dual 2-phase synchronous step-down controller Datasheet

LTC3858-2
Low IQ, Dual
2-Phase Synchronous
Step-Down Controller
DESCRIPTION
FEATURES
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
The LTC ®3858-2 is a high performance dual step-down
switching regulator controller that drives all N-channel
synchronous power MOSFET stages. A constant frequency
current mode architecture allows a phase-lockable frequency of up to 850kHz. Power loss and noise due to the
input capacitor ESR are minimized by operating the two
controller outputs out of phase.
Low Operating IQ: 170μA (One Channel On)
Wide Output Voltage Range: 0.8V ≤ VOUT ≤ 24V
Wide VIN Range: 4V to 38V
RSENSE or DCR Current Sensing
Out-of-Phase Controllers Reduce Required Input
Capacitance and Power Supply Induced Noise
OPTI-LOOP ® Compensation Minimizes COUT
Phase-Lockable Frequency (75kHz-850kHz)
Programmable Fixed Frequency (50kHz-900kHz)
Selectable Continuous, Pulse-Skipping or
Burst Mode ® Operation at Light Loads
Very Low Dropout Operation: 99% Duty Cycle
Adjustable Output Voltage Soft-Start or Tracking
Power Good Output Voltage Monitor
Low Shutdown IQ: 8μA
Internal LDO Powers Gate Drive from VIN or EXTVCC
No Current Foldback During Start-Up
5mm × 5mm QFN Package
The 170μA no-load quiescent current extends operating
life in battery-powered systems. OPTI-LOOP compensation allows the transient response to be optimized over
a wide range of output capacitance and ESR values. The
LTC3858-2 differs from the LTC3858 by having the overvoltage protection crowbar and short-circuit latchoff disabled.
A wide 4V to 38V input supply range encompasses a wide
range of intermediate bus voltages and battery chemistries.
Independent soft-start pins for each controller ramp the
output voltages during start-up. Current foldback limits
MOSFET heat dissipation during short-circuit conditions.
APPLICATIONS
n
n
n
L, LT, LTC, LTM, Burst Mode, OPTI-LOOP, μModule, PolyPhase, Linear Technology and the Linear
logo are registered trademarks and No RSENSE and UltraFast are trademarks of Linear Technology
Corporation. All other trademarks are the property of their respective owners. Protected by U.S.
Patents, including 5481178, 5705919, 5929620, 6100678, 6144194, 6177787, 6304066, 6580258.
Automotive Systems
Battery Operated Digital Devices
Distributed DC Power Systems
TYPICAL APPLICATION
High Efficiency Dual 8.5V/3.3V Step-Down Converter
22μF
50V
4.7μF
VIN
SW2
BG1
BG2
7.2μH
PGND
SENSE1+
SENSE2+
SENSE1–
SENSE2–
62.5k
150μF
680pF
20k
15k
SS1
0.1μF
VFB2
ITH2
SGND
193k
680pF
SS2
0.1μF
60
100
POWER LOSS
50
10
40
20
0.01Ω
VFB1
ITH1
1000
EFFICIENCY
70
30
0.007Ω
VOUT1
3.3V
5A
EFFICIENCY (%)
SW1
80
0.1μF
20k
VOUT2
8.5V
3.5A
150μF
VIN = 12V
VOUT = 3.3V
FIGURE 13 CIRCUIT
10
0
0.0001
0.001
0.01
0.1
1
OUTPUT CURRENT (A)
POWER LOSS (mW)
BOOST2
LTC3858-2
10000
90
TG2
BOOST1
3.3μH
100
INTVCC
TG1
0.1μF
Efficiency and Power Loss
vs Load Current
VIN
9V TO 38V
1
0.1
10
38582 TA01b
15k
38582 TA01a
38582f
1
LTC3858-2
ABSOLUTE MAXIMUM RATINGS
PIN CONFIGURATION
(Note 1)
SW1
TG1
PGOOD1
ILIM
SS1
ITH1
VFB1
SENSE1+
TOP VIEW
32 31 30 29 28 27 26 25
SENSE1– 1
24 BOOST1
23 BG1
FREQ 2
22 VIN
PHASMD 3
CLKOUT 4
21 PGND
33
SGND
PLLIN/MODE 5
20 EXTVCC
SGND 6
19 INTVCC
RUN1 7
18 BG2
RUN2 8
17 BOOST2
SW2
TG2
PGOOD2
SS2
ITH2
VFB2
SENSE2–
9 10 11 12 13 14 15 16
SENSE2+
Input Supply Voltage (VIN) ......................... –0.3V to 40V
Topside Driver Voltages
BOOST1, BOOST2 ................................. –0.3V to 46V
Switch Voltage (SW1, SW2) ......................... –5V to 40V
(BOOST1-SW1), (BOOST2-SW2) ................ –0.3V to 6V
RUN1, RUN2 ............................................... –0.3V to 8V
Maximum Current Sourced into Pin
from Source >8V ..............................................100μA
SENSE1+, SENSE2+, SENSE1–
SENSE2– Voltages ..................................... –0.3V to 28V
PLLIN/MODE Voltage ................................... –0.3V to 6V
ILIM, PHASMD, FREQ Voltages ............. –0.3V to INTVCC
EXTVCC ..................................................... –0.3V to 14V
ITH1, ITH2,VFB1, VFB2 Voltages....................... –0.3V to 6V
PGOOD1, PGOOD2 Voltages ....................... –0.3V to 6V
SS1, SS2, INTVCC Voltages ......................... –0.3V to 6V
Operating Junction Temperature Range
(Note 2).................................................. –40°C to 125°C
Maximum Junction Temperature (Note 3) ............ 125°C
Storage Temperature Range .................. –65°C to 150°C
UH PACKAGE
32-LEAD (5mm s 5mm) PLASTIC QFN
TJMAX = 125°C, θJA = 34°C/W
EXPOSED PAD (PIN 33) IS SGND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC3858EUH-2#PBF
LTC3858EUH-2#TRPBF
38582
32-Lead (5mm × 5mm) Plastic QFN
–40°C to 125°C
LTC3858IUH-2#PBF
LTC3858IUH-2#TRPBF
38582
32-Lead (5mm × 5mm) Plastic QFN
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 12V, VRUN1,2 = 5V, EXTVCC = 0V unless
otherwise noted.
SYMBOL
PARAMETER
VIN
Input Supply Operating Voltage
Range
VFB1,2
Regulated Feedback Voltage
CONDITIONS
MIN
TYP
4
(Note 4) ITH1,2 = 1.2V
–40°C to 125°C
–40°C to 85°C
IFB1,2
Feedback Current
(Note 4)
VREFLNREG
Reference Voltage Line Regulation
(Note 4) VIN = 4.5V to 38V
l
0.788
0.792
MAX
UNITS
38
V
0.800
0.800
0.812
0.808
V
V
±5
±50
nA
0.002
0.02
%/V
38582f
2
LTC3858-2
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 12V, VRUN1,2 = 5V, EXTVCC = 0V unless
otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
VLOADREG
Output Voltage Load Regulation
(Note 4)
Measured in Servo Loop,
ΔITH Voltage = 1.2V to 0.7V
(Note 4)
Measured in Servo Loop,
ΔITH Voltage = 1.2V to 2V
gm1,2
Transconductance Amplifier gm
(Note 4) ITH1,2 = 1.2V, Sink/Source = 5μA
IQ
Input DC Supply Current
(Note 5)
MIN
TYP
MAX
l
0.01
0.1
%
l
–0.01
–0.1
%
2
Pulse-Skipping or Forced Continuous RUN1 = 5V and RUN2 = 0V, VFB1 = 0.83V (No Load) or
RUN1 = 0V and RUN2 = 5V, VFB2 = 0.83V (No Load)
Mode (One Channel On)
Pulse-Skipping or Forced Continuous RUN1,2 = 5V, VFB1,2 = 0.83V (No Load)
Mode (Both Channels On)
UVLO
mmho
1.3
mA
2
mA
Sleep Mode (One Channel On)
RUN1 = 5V and RUN2 = 0V, VFB1 = 0.83V (No Load) or
RUN1 = 0V and RUN2 = 5V, VFB2 = 0.83V (No Load)
170
250
μA
Sleep Mode (Both Channels On)
RUN1,2 = 5V, VFB1,2 = 0.83V (No Load)
300
450
μA
Shutdown
RUN1,2 = 0V
Undervoltage Lockout
INTVCC Ramping Up
INTVCC Ramping Down
VOVL
Feedback Overvoltage Protection
Measured at VFB1,2, Relative to Regulated VFB1,2
ISENSE+
SENSE+ Pins Current
Each Channel
ISENSE–
SENSE– Pins Current
Each Channel
VOUT1,2 < INTVCC – 0.5V
VOUT1,2 > INTVCC + 0.5V
l
l
8
20
μA
3.6
4.0
3.8
4.2
4
V
V
7
10
13
%
±1
μA
±1
550
μA
μA
%
DFMAX
Maximum Duty Factor
In Dropout, FREQ = 0V
98
99
ISS1,2
Soft-Start Charge Current
VSS1,2 = 0V
0.7
1.0
1.4
VRUN1,2 On
RUN Pin On Threshold Voltage
VRUN1, VRUN2 Rising
1.21
1.26
1.31
l
VRUN1,2 Hyst RUN Pin Hysteresis Voltage
VSENSE(MAX)
UNITS
Maximum Current Sense
Threshold Voltage
50
VFB1,2 = 0.7V, VSENSE1–,2– = 3.3V, ILIM = 0
VFB1,2 = 0.7V, VSENSE1–,2– = 3.3V, ILIM = FLOAT
VFB1,2 = 0.7V, VSENSE1–,2– = 3.3V, ILIM = INTVCC
l
l
l
22
43
64
30
50
75
μA
V
mV
36
57
86
mV
mV
mV
Gate Driver
TG1,2
Pull-Up On-Resistance
Pull-Down On-Resistance
2.5
1.5
Ω
Ω
BG1,2
Pull-Up On-Resistance
Pull-Down On-Resistance
2.4
1.1
Ω
Ω
TG1,2 tr
TG1,2 tf
TG Transition Time:
Rise Time
Fall Time
(Note 6)
CLOAD = 3300pF
CLOAD = 3300pF
25
16
ns
ns
BG1,2 tr
BG1,2 tf
BG Transition Time:
Rise Time
Fall Time
(Note 6)
CLOAD = 3300pF
CLOAD = 3300pF
28
13
ns
ns
TG/BG t1D
Top Gate Off to Bottom Gate On Delay CLOAD = 3300pF Each Driver
Synchronous Switch-On Delay Time
30
ns
BG/TG t1D
Bottom Gate Off to Top Gate On Delay CLOAD = 3300pF Each Driver
Top Switch-On Delay Time
30
ns
tON(MIN)
Minimum On-Time
95
ns
(Note 7)
38582f
3
LTC3858-2
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 12V, VRUN1,2 = 5V, EXTVCC = 0V unless
otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
4.85
5.1
5.35
V
0.7
1.1
%
INTVCC Linear Regulator
VINTVCCVIN
Internal VCC Voltage
6V < VIN < 38V, VEXTVCC = 0V
VLDOVIN
INTVCC Load Regulation
ICC = 0mA to 50mA, VEXTVCC = 0V
VINTVCCEXT
Internal VCC Voltage
6V < VEXTVCC < 13V
VLDOEXT
INTVCC Load Regulation
ICC = 0mA to 50mA, VEXTVCC = 8.5V
VEXTVCC
EXTVCC Switchover Voltage
EXTVCC Ramping Positive
VLDOHYS
EXTVCC Hysteresis Voltage
4.85
4.5
5.1
5.35
V
0.6
1.1
%
4.7
4.9
250
V
mV
Oscillator and Phase-Locked Loop
f25kΩ
Programmable Frequency
RFREQ = 25k, PLLIN/MODE = DC Voltage
f65kΩ
Programmable Frequency
RFREQ = 65k, PLLIN/MODE = DC Voltage
f105kΩ
Programmable Frequency
RFREQ = 105k, PLLIN/MODE = DC Voltage
105
375
440
kHz
505
835
kHz
kHz
fLOW
Low Fixed Frequency
VFREQ = 0V, PLLIN/MODE = DC Voltage
320
350
380
kHz
fHIGH
High Fixed Frequency
VFREQ = INTVCC, PLLIN/MODE = DC Voltage
485
535
585
kHz
fSYNC
Synchronizable Frequency
PLLIN/MODE = External Clock
850
kHz
0.4
V
±1
μA
l
75
PGOOD1 and PGOOD2 Outputs
VPGL
PGOOD Voltage Low
IPGOOD
PGOOD Leakage Current
VPGOOD = 5V
VPG
PGOOD Trip Level
VFB with Respect to Set Regulated Voltage
VFB Ramping Negative
Hysteresis
–13
–10
2.5
–7
%
%
VFB with Respect to Set Regulated Voltage
VFB Ramping Positive
Hysteresis
7
10
2.5
13
%
%
tPG
IPGOOD = 2mA
Delay for Reporting a Fault (PGOOD
Low)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Ratings for extended periods may affect device reliability and
lifetime.
Note 2: The LTC3858-2 is tested under pulsed load conditions such that
TJ ≈ TA. The LTC3858E-2 is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 125°C operating
junction temperature range are assured by design, characterization and
correlation with statistical process controls. The LTC3858I-2 is guaranteed
over the full –40°C to 125°C operating junction temperature range.
Note that the maximum ambient temperature is determined by specific
operating conditions in conjunction with board layout, the rated package
thermal resistance and other environmental factors.
0.2
25
μs
Note 3: TJ is calculated from the ambient temperature TA and power
dissipation PD according to the following formula:
TJ = TA + (PD • 34°C/W)
Note 4: The LTC3858-2 is tested in a feedback loop that servos VITH1,2 to
a specified voltage and measures the resultant VFB1,2. The specification at
85°C is not tested in production. This specification is assured by design,
characterization and correlation to production testing at 125°C.
Note 5: Dynamic supply current is higher due to the gate charge being
delivered at the switching frequency. See the Applications information
section.
Note 6: Rise and fall times are measured using 10% and 90% levels.
Delay times are measured using 50% levels
Note 7: The minimum on-time condition is specified for an inductor
peak-to-peak ripple current ≥ of 40% IMAX (See Minimum On-Time
Considerations in the Applications Information section).
38582f
4
LTC3858-2
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency and Power Loss
vs Output Current
10000
1000
100
30
20
10
0
0.0001
Burst Mode
OPERATION
10
PULSESKIPPING
MODE
1
FORCED
CONTINUOUS
MODE
0.1
0.001
0.01
0.1
1
10
OUTPUT CURRENT (A)
EFFICIENCY (%)
60
80
98
94
70
VIN = 12V
60
50
40
30
10
VOUT = 3.3V
FIGURE 13 CIRCUIT
0.001
0.01
0.1
1
OUTPUT CURRENT (A)
38582 G01
38582 G04
Inductor Current at Light Load
86
82
80
0
5
10
15 20 25 30
INPUT VOLTAGE (V)
35
40
38582 G03
Load Step
(Forced Continuous Mode)
Load Step (Pulse-Skipping Mode)
VOUT
100mV/DIV
ACCOUPLED
IL
2A/DIV
IL
2A/DIV
VOUT = 3.3V
20μs/DIV
FIGURE 13 CIRCUIT
88
10
VOUT
100mV/DIV
ACCOUPLED
IL
2A/DIV
90
38582 G02
Load Step (Burst Mode Operation)
VOUT
100mV/DIV
ACCOUPLED
92
84
20
0
0.0001
FIGURE 13 CIRCUIT
VOUT = 3.3V
IOUT = 4A
96
VIN = 5V
EFFICIENCY (%)
90
70
40
100
POWER LOSS (mW)
EFFICIENCY (%)
FIGURE 13 CIRCUIT
90 VIN = 12V
VOUT = 3.3V
80
50
Efficiency vs Input Voltage
Efficiency vs Output Current
100
20μs/DIV
VOUT = 3.3V
FIGURE 13 CIRCUIT
38585 G05
38582 G06
VOUT = 3.3V
20μs/DIV
FIGURE 13 CIRCUIT
Tracking Start-Up
Soft-Start
FORCED
CONTINUOUS
MODE
VOUT2
2V/DIV
VOUT2
2V/DIV
Burst Mode
OPERATION
2A/DIV
VOUT1
2V/DIV
VOUT1
2V/DIV
PULSESKIPPING
MODE
VOUT = 3.3V
2μs/DIV
ILOAD = 200μA
FIGURE 13 CIRCUIT
38582 G07
20ms/DIV
FIGURE 13 CIRCUIT
38582 G08
20ms/DIV
FIGURE 13 CIRCUIT
38572 G09
38582f
5
LTC3858-2
TYPICAL PERFORMANCE CHARACTERISTICS
Total Input Supply Current
vs Input Voltage
300μA LOAD
250
200
NO LOAD
150
100
50
30
25
20
INPUT VOLTAGE (V)
10
15
35
INTVCC
5.0
EXTVCC RISING
4.8
EXTVCC FALLING
4.6
40
5.0
80
55
30
TEMPERATURE (°C)
5
ILIM = GND
ILIM = FLOAT
ILIM = INTVCC
–150
–200
–250
–300
–350
–400
–450
–500
–20
5% DUTY CYCLE
0
0.2
0.4 0.6 0.8 1.0
ITH PIN VOLTAGE
1.2
–550
–600
1.4
0
QUIESCENT CURRENT (μA)
MAXIMUM CURRENT SENSE VOLTAGE (mV)
210
60
ILIM = FLOAT
50
40
ILIM = GND
30
60
ILIM = FLOAT
40
ILIM = GND
20
20
0
10 20 30 40 50 60 70 80 90 100
DUTY CYCLE (%)
Shutdown Current vs Temperature
Quiescent Current vs Temperature
ILIM = INTVCC
40
38582 G15
230
90
35
ILIM = INTVCC
38582 G14
Foldback Current Limit
70
15 20 25 30
INPUT VOLTAGE (V)
80
0
25
10
15
20
5
VSENSE COMMON MODE VOLTAGE (V)
38582 G13
80
10
38582 G12
MAXIMUM CURRENT SENSE VOLTAGE (mV)
–100
SENSE– CURRENT (μA)
CURRENT SENSE THRESHOLD (mV)
–50
20
5
Maximum Current Sense
Threshold vs Duty Cycle
0
PULSE-SKIPPING
FORCED CONTINUOUS
Burst Mode OPERATION
(FALLING)
Burst Mode OPERATION
(RISING)
–40
0
130
SENSE– Pin Input Bias Current
80
0
105
38582 G11
Maximum Current Sense Voltage
vs ITH Voltage
40
5.1
4.2
38582 G10
60
5.2
5.1
4.4
4.0
–45 –20
0
5
5.2
10
PLLIN/MODE = 0
VIN = 12V
VOUT = 3.3V
ONE CHANNEL ON
SHUTDOWN CURRENT (μA)
SUPPLY CURRENT (μA)
300
5.4
INTVCC VOLTAGE (V)
FIGURE 12 CIRCUIT
VOUT = 3.3V
ONE CHANNEL ON
350
INTVCC Line Regulation
5.2
5.6
EXTVCC AND INTVCC VOLTAGE (V)
400
EXTVCC Switchover and INTVCC
Voltages vs Temperature
190
170
150
9
8
7
6
5
130
10
0
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
FEEDBACK VOLTAGE (V)
38582 G16
110
–45
–20
80
5
55
30
TEMPERATURE (°C)
105
130
38582 G17
4
–45 –20
55
30
80
5
TEMPERATURE (°C)
105
130
38582 G18
38582f
6
LTC3858-2
TYPICAL PERFORMANCE CHARACTERISTICS
Soft-Start Pull-Up Current
vs Temperature
REGULATED FEEDBACK VOLTAGE (mV)
1.35
1.15
1.30
1.10
RUN PIN VOLTAGE (V)
SS PULL-UP CURRENT (μA)
808
1.40
1.20
1.05
1.00
0.95
0.90
1.25
1.20
1.15
1.10
1.05
1.00
0.85
0.95
0.80
–45 –20
80
55
30
TEMPERATURE (°C)
5
105
0.90
–45
130
–20
55
30
5
80
TEMPERATURE (°C)
38582 G19
798
796
794
800
12
700
600
10
8
6
4
105
FREQ = INTVCC
500
FREQ = GND
400
300
100
5
130
10
25
20
30
15
INPUT VOLTAGE (V)
35
0
–45 –20
40
80
55
30
TEMPERATURE (°C)
5
105
Undervoltage Lockout Threshold
vs Temperature
INTVCC vs Load Current
5.50
4.4
FREQ = GND
130
38582 G24
38582 G23
Oscillator Frequency
vs Input Voltage
130
200
0
105
80
55
30
TEMPERATURE (°C)
5
Oscillator Frequency
vs Temperature
14
38582 G22
356
800
38582 G21
2
VOUT = 28V
80
5
55
30
TEMPERATURE (°C)
802
792
–45 –20
130
FREQUENCY (kHz)
VOUT = 3.3V
–20
804
Shutdown Input Current
vs Input Voltage
INPUT CURRENT (μA)
SENSE– CURRENT (μA)
50
0
–50
–100
–150
–200
–250
–300
–350
–400
–450
–500
–550
–600
–45
105
806
38582 G20
SENSE– Pin Input Current
vs Temperature
VIN = 12V
4.3
354
5.25
4.2
352
350
348
EXTVCC = 0V
INTVCC VOLTAGE (V)
INTVCC VOLTAGE (V)
OSCILLATOR FREQUENCY (kHz)
Regulated Feedback Voltage
vs Temperature
Shutdown (RUN) Threshold
vs Temperature
4.1
4.0
3.9
3.8
3.7
3.6
346
5.00
EXTVCC = 8.5V
4.75
EXTVCC = 5V
4.50
4.25
3.5
344
5
10
25
20
30
15
INPUT VOLTAGE (V)
35
40
38582 G25
3.4
–45
4.00
–20
55
30
5
80
TEMPERATURE (°C)
105
130
38582 G26
0
20
60
80
40
LOAD CURRENT (mA)
100
38582 G27
38582f
7
LTC3858-2
PIN FUNCTIONS
SENSE1–, SENSE2– (Pin 1, Pin 9): The (–) Input to the
Differential Current Comparators. When greater than
INTVCC – 0.5V, the SENSE– pin supplies current to the
current comparator.
FREQ (Pin 2): The Frequency Control Pin for the Internal
Voltage-Controlled Oscillator (VCO). Connecting this pin
to GND forces the VCO to a fixed low frequency of 350kHz.
Connecting this pin to INTVCC forces the VCO to a fixed high
frequency of 535kHz. Other frequencies between 50kHz
and 900kHz can be programmed using a resistor between
FREQ and GND. An internal 20μA pull-up current develops
the voltage to be used by the VCO to control the frequency
PHASMD (Pin 3): Control input to phase selector which
determines the phase relationships between controller 1,
controller 2 and the CLKOUT signal. Pulling this pin to
ground forces TG2 and CLKOUT to be out of phase 180°
and 60° with respect to TG1. Connecting this pin to INTVCC forces TG2 and CLKOUT to be out of phase 240° and
120° with respect to TG1. Floating this pin forces TG2 and
CLKOUT to be out of phase 180° and 90° with respect to
TG1. Refer to the Table 1.
CLKOUT (Pin 4): Output clock signal available to daisychain other controller ICs for additional MOSFET driver
stages/phases. The output levels swing from INTVCC to
ground.
PLLIN/MODE (Pin 5): External Synchronization Input to
Phase Detector and Forced Continuous Mode Input. When
an external clock is applied to this pin, the phase-locked
loop will force the rising TG1 signal to be synchronized
with the rising edge of the external clock. When not synchronizing to an external clock, this input, which acts on
both controllers, determines how the LTC3858-2 operates
at light loads. Pulling this pin to ground selects Burst Mode
operation. An internal 100k resistor to ground also invokes
Burst Mode operation when the pin is floated. Tying this pin
to INTVCC forces continuous inductor current operation.
Tying this pin to a voltage greater than 1.2V and less than
INTVCC – 1.3V selects pulse-skipping operation.
SGND (Pin 6, Exposed Pad Pin 33): Small-signal ground
common to both controllers, must be routed separately
from high current grounds to the common (–) terminals
of the CIN capacitors. The exposed pad must be soldered
to the PCB for rated thermal performance.
RUN1, RUN2 (Pin 7, Pin 8): Digital Run Control Inputs for
Each Controller. Forcing either of these pins below 1.2V
shuts down that controller. Forcing both of these pins
below 0.7V shuts down the entire LTC3858-2, reducing
quiescent current to approximately 8μA.
ILIM (Pin 28): Current Comparator Sense Voltage Range
Inputs. Tying this pin to SGND, FLOAT or INTVCC sets the
maximum current sense threshold to one of three different
levels for both comparators.
38582f
8
LTC3858-2
PIN FUNCTIONS
INTVCC (Pin 19): Output of the Internal Linear Low Dropout
Regulator. The driver and control circuits are powered from
this voltage source. Must be decoupled to power ground
with a minimum of 4.7μF ceramic or other low ESR capacitor. Do not use the INTVCC pin for any other purpose.
EXTVCC (Pin 20): External Power Input to an Internal LDO
Connected to INTVCC. This LDO supplies INTVCC power,
bypassing the internal LDO powered from VIN whenever
EXTVCC is higher than 4.7V. See EXTVCC Connection in
the Applications Information section. Do not exceed 14V
on this pin.
PGND (Pin 21): Driver Power Ground. Connects to the
sources of bottom (synchronous) N-channel MOSFETs
and the (–) terminal(s) of CIN.
VIN (Pin 22): Main Input Supply Pin. A bypass capacitor
should be tied between this pin and the signal ground pin.
BG1, BG2 (Pin 23, Pin 18): High Current Gate Drives
for Bottom (Synchronous) N-Channel MOSFETs. Voltage
swing at these pins is from ground to INTVCC.
BOOST1, BOOST2 (Pin 24, Pin 17): Bootstrapped Supplies
to the Topside Floating Drivers. Capacitors are connected
between the BOOST and SW pins and Schottky diodes are
tied between the BOOST and INTVCC pins. Voltage swing
at the BOOST pins is from INTVCC to (VIN + INTVCC).
SW1, SW2 (Pin 25, Pin 16): Switch Node Connections
to Inductors.
TG1, TG2 (Pin 26, Pin 15): High Current Gate Drives for
Top N-Channel MOSFETs. These are the outputs of floating drivers with a voltage swing equal to INTVCC – 0.5V
superimposed on the switch node voltage SW.
PGOOD1, PGOOD2 (Pin 27, Pin 14): Open-Drain Logic
Output. PGOOD1,2 is pulled to ground when the voltage
on the VFB1,2 pin is not within ±10% of its set point.
SS1, SS2 (Pin 29, Pin 13): External Soft-Start Input. The
LTC3858-2 regulates the VFB1,2 voltage to the smaller of
0.8V or the voltage on the SS1,2 pin. An internal 1μA pullup current source is connected to this pin. A capacitor to
ground at this pin sets the ramp time to final regulated
output voltage. Alternatively, a resistor divider on another
voltage supply connected to this pin allows the LTC3858-2
output to track the other supply during start-up.
ITH1, ITH2 (Pin 30, Pin 12): Error Amplifier Outputs and
Switching Regulator Compensation Points. Each associated channel’s current comparator trip point increases
with this control voltage.
VFB1, VFB2 (Pin 31, Pin 11): Receives the remotely sensed
feedback voltage for each controller from an external
resistive divider across the output.
SENSE1+, SENSE2+ (Pin 32, Pin 10): The (+) Input to
the differential current comparators that are normally
connected to inductor DCR sensing networks or current
sensing resistors. The ITH pin voltage and controlled offsets
between the SENSE– and SENSE+ pins in conjunction with
RSENSE set the current trip threshold.
38582f
9
4.7V
20
EXTVCC
22
VIN
28
ILIM
5
PLLIN/MODE
2
FREQ
+
–
PGOOD2
14
100k
20μA
LDO
EN
5.1V
0.88V
6 SGND
CLP
19 INTVCC
5.1V
LDO
EN
PFD
CLK1
CLK2
4
3
VCO
CLKOUT
PHASMD
CURRENT
LIMIT
SYNC
DET
0.72V
VFB2
0.72V
VFB1
0.88V
11V
0.5μA
RUN
7, 8
ICMP
SHDN
RST
2(VFB)
SLOPE COMP
2.7V
0.55V
Q
Q
BOT
+–
3mV
OV
IR
SLEEP
SHDN
TOP ON
FOLDBACK
–+
0.425V
R
S
DROP
OUT
DET
TOP
EA
SHDN
INTVCC
0.88V
1μA
0.80V
TRACK/SS
SWITCH
LOGIC BOT
–
+
–
–
+
–
+
PGOOD1
27
+
+
–
+
+
–
–
+
–
+
10
–
DUPLICATE FOR SECOND
CONTROLLER CHANNEL
SS
29, 13
ITH
30, 12
VFB
31, 11
SENSE–
1, 9
SENSE+
32, 10
21
PGND
BG
23, 18
SW
25, 16
TG
26, 15
BOOST
24, 17
38582 FD
CSS
CC2
CC
RA
L
VIN
RB
CB
DB
INTVCC
RC
D
RSENSE
COUT
CIN
VOUT
LTC3858-2
FUNCTIONAL DIAGRAM
38582f
LTC3858-2
OPERATION (Refer to the Functional Diagram)
Table 1 summarizes the differences between the LTC3858-2
and its sister parts, the LTC3858 and LTC3858-1. The
LTC3858-2 uses a constant frequency, current mode
step-down architecture with the two controller channels
operating 180 degrees out of phase. During normal operation, each external top MOSFET is turned on when the
clock for that channel sets the RS latch, and is turned off
when the main current comparator, ICMP, resets the RS
latch. The peak inductor current at which ICMP trips and
resets the latch is controlled by the voltage on the ITH pin,
which is the output of the error amplifier, EA. The error
amplifier compares the output voltage feedback signal at
the VFB pin (which is generated with an external resistor
divider connected across the output voltage, VOUT , to
ground) to the internal 0.800V reference voltage. When the
load current increases, it causes a slight decrease in VFB
relative to the reference, which causes the EA to increase
the ITH voltage until the average inductor current matches
the new load current.
After the top MOSFET is turned off each cycle, the bottom
MOSFET is turned on until either the inductor current starts
to reverse, as indicated by the current comparator IR, or
the beginning of the next clock cycle.
INTVCC/EXTVCC Power
Power for the top and bottom MOSFET drivers and most
other internal circuitry is derived from the INTVCC pin. When
the EXTVCC pin is left open or tied to a voltage less than
4.7V, the VIN LDO (low dropout linear regulator) supplies
5.1V from VIN to INTVCC. If EXTVCC is taken above 4.7V,
the VIN LDO is turned off and the EXTVCC LDO is turned
on. Once enabled, the EXTVCC LDO supplies 5.1V from
EXTVCC to INTVCC. Using the EXTVCC pin allows the INTVCC
power to be derived from a high efficiency external source
such as one of the LTC3858-2 switching regulator outputs.
Each top MOSFET driver is biased from the floating bootstrap capacitor, CB, which normally recharges during each
switching cycle through an external diode when the top
MOSFET turns off. If the input voltage, VIN, decreases to
a voltage close to VOUT , the loop may enter dropout and
attempt to turn on the top MOSFET continuously. The
dropout detector detects this and forces the top MOSFET
off for about one-twelfth of the clock period every tenth
cycle to allow CB to recharge.
Table 1. Summary of the Differences Between LTC3858, LTC3858-1 and LTC3858-2
LTC3858
LTC3858-1
LTC3858-2
Yes, But Can Be Defeated
Yes, But Can Be Defeated
Not Present
BG Forced On
(Bottom MOSFET “Crowbar”)
No
BG Forced On
(Bottom MOSFET “Crowbar”)
No
BG Not Forced On
(Behavior Depends on Light Load Mode)
Yes
Independent PGOOD1 and PGOOD2 Pins?
Yes
No, PGOOD1 Only
Yes
CLKOUT/PHASMD Pins for PolyPhase
Yes
No
Yes
Short-Circuit Latchoff Feature?
Overvoltage Protection
Optional Tracking Start-Up?
Adjustable Current Limit (ILIM Pin)
Package
Yes
No
Yes
5mm × 5mm QFN
4mm × 5mm QFN and
Narrow SSOP
5mm × 5mm QFN
38582f
11
LTC3858-2
OPERATION (Refer to the Functional Diagram)
Shutdown and Start-Up (RUN1, RUN2
and SS1, SS2 Pins)
The two channels of the LTC3858-2 can be independently
shut down using the RUN1 and RUN2 pins. Pulling either of
these pins below 1.26V shuts down the main control loop
for that controller. Pulling both pins below 0.7V disables
both controllers and most internal circuits, including the
INTVCC LDOs. In this state, the LTC3858-2 draws only 8μA
of quiescent current.
The RUN pin may be externally pulled up or driven directly
by logic. When driving the RUN pin with a low impedance
source, do not exceed the absolute maximum rating of
8V. The RUN pin has an internal 11V voltage clamp that
allows the RUN pin to be connected through a resistor to a
higher voltage (for example, VIN), so long as the maximum
current into the RUN pin does not exceed 100μA.
The start-up of each controller’s output voltage, VOUT , is
controlled by the voltage on the SS pin for that channel.
When the voltage on the SS pin is less than the 0.8V
internal reference, the LTC3858-2 regulates the VFB voltage to the SS pin voltage instead of the 0.8V reference.
This allows the SS pin to be used to program a soft-start
by connecting an external capacitor from the SS pin to
SGND. An internal 1μA pull-up current charges this capacitor creating a voltage ramp on the SS pin. As the SS
voltage rises linearly from 0V to 0.8V (and beyond up to
the absolute maximum rating of 6V), the output voltage
VOUT rises smoothly from zero to its final value.
Alternatively, the SS pin can be used to cause the startup of VOUT to track that of another supply. Typically, this
requires connecting to the SS pin an external resistor
divider from the other supply to ground (see the Applications Information section).
Light Load Current Operation (Burst Mode Operation,
Pulse-Skipping or Forced Continuous)
(PLLIN/MODE Pin)
The LTC3858-2 can be enabled to enter high efficiency
Burst Mode operation, constant frequency pulse-skipping
mode, or forced continuous conduction mode at low
load currents. To select Burst Mode operation, tie the
PLLIN/ MODE pin to ground. To select forced continuous
operation, tie the PLLIN/MODE pin to INTVCC. To select
pulse-skipping mode, tie the PLLIN/MODE pin to a DC
voltage greater than 1.2V and less than INTVCC – 1.3V.
When a controller is enabled for Burst Mode operation, the
minimum peak current in the inductor is set to approximately 30% of the maximum sense voltage even though
the voltage on the ITH pin indicates a lower value. If the
average inductor current is higher than the load current,
the error amplifier EA will decrease the voltage on the ITH
pin. When the ITH voltage drops below 0.425V, the internal
sleep signal goes high (enabling “sleep” mode) and both
external MOSFETs are turned off.
In sleep mode, much of the internal circuitry is turned off,
reducing the quiescent current. If one channel is shut down
and the other channel is in sleep mode, the LTC3858-2
draws only 170μA of quiescent current. If both channels
are in sleep mode, the LTC3858-2 draws only 300μA of quiescent current. In sleep mode, the load current is supplied
by the output capacitor. As the output voltage decreases,
the EA’s output begins to rise. When the output voltage
drops enough, the ITH pin is reconnected to the output
of the EA, the sleep signal goes low, and the controller
resumes normal operation by turning on the top external
MOSFET on the next cycle of the internal oscillator.
When a controller is enabled for Burst Mode operation,
the inductor current is not allowed to reverse. The reverse
current comparator, IR, turns off the bottom external
MOSFET just before the inductor current reaches zero,
preventing it from reversing and going negative. Thus,
the controller is in discontinuous operation.
38582f
12
LTC3858-2
OPERATION (Refer to the Functional Diagram)
In forced continuous operation or when clocked by an
external clock source to use the phase-locked loop (see
the Frequency Selection and Phase-Locked Loop section),
the inductor current is allowed to reverse at light loads
or under large transient conditions. The peak inductor
current is determined by the voltage on the ITH pin, just
as in normal operation. In this mode, the efficiency at light
loads is lower than in Burst Mode operation. However,
continuous operation has the advantages of lower output
voltage ripple and less interference to audio circuitry. In
forced continuous mode, the output ripple is independent
of load current.
When the PLLIN/MODE pin is connected for pulse-skipping
mode, the LTC3858-2 operates in PWM pulse-skipping
mode at light loads. In this mode, constant frequency
operation is maintained down to approximately 1% of
designed maximum output current. At very light loads, the
current comparator, ICMP, may remain tripped for several
cycles and force the external top MOSFET to stay off for
the same number of cycles (i.e., skipping pulses). The
inductor current is not allowed to reverse (discontinuous
operation). This mode, like forced continuous operation,
exhibits low output ripple as well as low audio noise and
reduced RF interference when compared to Burst Mode
operation. It provides higher light load efficiency than
forced continuous mode, but not nearly as high as Burst
Mode operation.
Frequency Selection and Phase-Locked Loop
(FREQ and PLLIN/MODE Pins)
The selection of switching frequency is a trade-off between
efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching
losses, but requires larger inductance and/or capacitance
to maintain low output ripple voltage.
The switching frequency of the LTC3858-2’s controllers
can be selected using the FREQ pin.
If the PLLIN/MODE pin is not being driven by an external
clock source, the FREQ pin can be tied to SGND, tied to
INTVCC or programmed through an external resistor. Tying
FREQ to SGND selects 350kHz while tying FREQ to INTVCC
selects 535kHz. Placing a resistor between FREQ and SGND
allows the frequency to be programmed between 50kHz
and 900kHz, as shown in Figure 10.
A phase-locked loop (PLL) is available on the LTC3858-2
to synchronize the internal oscillator to an external clock
source that is connected to the PLLIN/MODE pin. The
phase detector adjusts the voltage (through an internal
lowpass filter) of the VCO input to align the turn-on of
controller 1’s external top MOSFET to the rising edge of
the synchronizing signal. Thus, the turn-on of controller 2’s
external top MOSFET is 180 degrees out of phase to the
rising edge of the external clock source.
The VCO input voltage is pre-biased to the operating
frequency set by the FREQ pin before the external clock
is applied. If prebiased near the external clock frequency,
the PLL loop only needs to make slight changes to the
VCO input in order to synchronize the rising edge of the
external clock’s to the rising edge of TG1. The ability to
pre-bias the loop filter allows the PLL to lock-in rapidly
without deviating far from the desired frequency.
The typical capture range of the phase-locked loop is from
approximately 55kHz to 1MHz, with a guarantee over all
manufacturing variations to be between 75kHz and 850kHz.
In other words, the LTC3858-2’s PLL is guaranteed to lock
to an external clock source whose frequency is between
75kHz and 850kHz.
The typical input clock thresholds on the PLLIN/MODE
pin are 1.6V (rising) and 1.1V (falling).
38582f
13
LTC3858-2
OPERATION (Refer to the Functional Diagram)
PolyPhase® Applications (CLKOUT and PHASMD Pins)
The LTC3858-2 features two pins (CLKOUT and PHASMD)
that allow other controller ICs to be daisy-chained with the
LTC3858-2 in PolyPhase applications. The clock output
signal on the CLKOUT pin can be used to synchronize
additional power stages in a multiphase power supply
solution feeding a single, high current output or multiple
separate outputs. The PHASMD pin is used to adjust the
phase of the CLKOUT signal as well as the relative phases
between the two internal controllers, as summarized in
Table 2. The phases are calculated relative to the zero
degrees phase being defined as the rising edge of the top
gate driver output of controller 1 (TG1). The CLKOUT pin
swings from ground to INTVCC with a pull-down impedance
of 120Ω and a pull-up impedance of 150Ω.
Table 2
VPHASMD
CONTROLLER 2-PHASE
CLKOUT PHASE
GND
180°
60°
Floating
180°
90°
INTVCC
240°
120°
Output Overvoltage Protection
An overvoltage (OV) comparator guards against transient
overshoots as well as other more serious conditions that
may overvoltage the output. When the VFB pin rises by
more than 10% above its regulation point of 0.800V, the
top MOSFET is turned off until the overvoltage condition
is cleared.
The state of the bottom MOSFET during the overvoltage
condition depends on the light load mode of operation,
as selected by the PLLIN/MODE pin. In forced continuous mode, the bottom gate driver BG naturally turns on
whenever the top gate driver TG is off, resulting in negative inductor current which discharges the output to (try
to) bring it back into regulation. In pulse-skipping mode,
BG is held off most of the time but is turned on for a brief
pulse every ten clock cycles (for an effective BG-on duty
cycle of ~1%) to refresh the BOOST-SW capacitor. This
causes a slightly negative average inductor current which,
in addition to whatever load current is present, may slowly
discharge the output. In Burst Mode operation, BG is held
off continuously, leaving only the load current to discharge
the output to bring it back into regulation.
Power Good (PGOOD1 and PGOOD2) Pins
Each PGOOD pin is connected to an open drain of an
internal N-channel MOSFET. The MOSFET turns on and
pulls the PGOOD pin low when the corresponding VFB pin
voltage is not within ±10% of the 0.8V reference voltage.
The PGOOD pin is also pulled low when the corresponding
RUN pin is low (shut down). When the VFB pin voltage
is within the ±10% requirement, the MOSFET is turned
off and the pin is allowed to be pulled up by an external
resistor to a source no greater than 6V.
Foldback Current
When the output voltage falls to less than 70% of its
nominal level, foldback current limiting is activated, progressively lowering the peak current limit in proportion to
the severity of the overcurrent or short-circuit condition.
Foldback current limiting is disabled during the soft-start
interval (as long as the VFB voltage is keeping up with the
TRACK/SS voltage).
Theory and Benefits of 2-Phase Operation
Why the need for 2-phase operation? Up until the 2-phase
family, constant frequency dual switching regulators
operated both channels in phase (i.e., single phase
operation). This means that both switches turned on at
the same time, causing current pulses of up to twice the
amplitude of those for one regulator to be drawn from the
input capacitor and battery. These large amplitude current
pulses increased the total RMS current flowing from the
input capacitor, requiring the use of more expensive input
capacitors and increasing both EMI and losses in the input
capacitor and battery.
With 2-phase operation, the two channels of the dual
switching regulator are operated 180 degrees out of phase.
This effectively interleaves the current pulses drawn by the
switches, greatly reducing the overlap time where they add
together. The result is a significant reduction in total RMS
input current, which in turn allows less expensive input
capacitors to be used, reduces shielding requirements for
EMI and improves real world operating efficiency.
38582f
14
LTC3858-2
OPERATION (Refer to the Functional Diagram)
Figure 1 compares the input waveforms for a representative
single-phase dual switching regulator to the LTC3858-2
2-phase dual switching regulator. An actual measurement of
the RMS input current under these conditions shows that
2-phase operation dropped the input current from 2.53ARMS
to 1.55ARMS. While this is an impressive reduction in itself,
remember that the power losses are proportional to IRMS2,
meaning that the actual power wasted is reduced by a
factor of 2.66. The reduced input ripple voltage also means
less power is lost in the input power path, which could
include batteries, switches, trace/connector resistances
and protection circuitry. Improvements in both conducted
and radiated EMI also directly accrue as a result of the
reduced RMS input current and voltage.
Of course, the improvement afforded by 2-phase operation is a function of the dual switching regulator’s relative
duty cycles which, in turn, are dependent upon the input
voltage VIN (Duty Cycle = VOUT/VIN). Figure 2 shows how
the RMS input current varies for single phase and 2-phase
operation for 3.3V and 5V regulators over a wide input
voltage range.
It can readily be seen that the advantages of 2-phase operation are not just limited to a narrow operating range,
for most applications is that 2-phase operation will reduce
the input capacitor requirement to that for just one channel operating at maximum current and 50% duty cycle.
5V SWITCH
20V/DIV
3.3V SWITCH
20V/DIV
INPUT CURRENT
5A/DIV
INPUT VOLTAGE
500mV/DIV
IIN(MEAS) = 2.53ARMS
IIN(MEAS) = 1.55ARMS
38582 F01
Figure 1. Input Waveforms Comparing Single-Phase (a) and 2-Phase (b) Operation for Dual Switching Regulators
Converting 12V to 5V and 3.3V at 3A Each. The Reduced Input Ripple with the 2-Phase Regulator Allows
Less Expensive Input Capacitors, Reduces Shielding Requirements for EMI and Improves Efficiency
3.0
SINGLE PHASE
DUAL CONTROLLER
INPUT RMS CURRENT (A)
2.5
2.0
1.5
2-PHASE
DUAL CONTROLLER
1.0
0.5
0
VO1 = 5V/3A
VO2 = 3.3V/3A
0
10
20
30
INPUT VOLTAGE (V)
40
38582 F02
Figure 2. RMS Input Current Comparison
38582f
15
LTC3858-2
APPLICATIONS INFORMATION
The Typical Application on the first page is a basic
LTC3858-2 application circuit. LTC3858-2 can be configured to use either DCR (inductor resistance) sensing or low
value resistor sensing. The choice between the two current
sensing schemes is largely a design trade-off between
cost, power consumption and accuracy. DCR sensing
is becoming popular because it saves expensive current
sensing resistors and is more power efficient, especially
in high current applications. However, current sensing
resistors provide the most accurate current limits for the
controller. Other external component selection is driven
by the load requirement, and begins with the selection of
RSENSE (if RSENSE is used) and inductor value. Next, the
power MOSFETs and Schottky diodes are selected. Finally,
input and output capacitors are selected.
Filter components mutual to the sense lines should be
placed close to the LTC3858-2, and the sense lines should
run close together to a Kelvin connection underneath the
current sense element (shown in Figure 3). Sensing current elsewhere can effectively add parasitic inductance
and capacitance to the current sense element, degrading
the information at the sense terminals and making the
programmed current limit unpredictable. If inductor DCR
sensing is used (Figure 4b), resistor R1 should be placed
close to the switching node, to prevent noise from coupling
into sensitive small-signal nodes.
TO SENSE FILTER,
NEXT TO THE CONTROLLER
COUT
3858 F03
Current Limit Programming
The ILIM pin is a tri-level logic input which sets the maximum
current limit of the converter. When ILIM is grounded, the
maximum current limit threshold voltage of the current
comparator is programmed to be 30mV. When ILIM is
floated, the maximum current limit threshold is 50mV.
When ILIM is tied to INTVCC, the maximum current limit
threshold is set to 75mV.
SENSE+ and SENSE– Pins
The SENSE+ and SENSE– pins are the inputs to the current
comparators. The common mode voltage range on these
pins is 0V to 28V (Abs Max), enabling the LTC3858-2 to
regulate output voltages up to a nominal 24V (allowing
plenty of margin for tolerances and transients).
The SENSE+ pin is high impedance over the full common
mode range, drawing at most ±1μA. This high impedance
allows the current comparators to be used in inductor
DCR sensing.
The impedance of the SENSE– pin changes depending on
the common mode voltage. When SENSE– is less than
INTVCC – 0.5V, a small current of less than 1μA flows out
of the pin. When SENSE– is above INTVCC + 0.5V, a higher
current (~550μA) flows into the pin. Between INTVCC –
0.5V and INTVCC + 0.5V, the current transitions from the
smaller current to the higher current.
INDUCTOR OR RSENSE
Figure 3. Sense Lines Placement with Inductor or Sense Resistor
Low Value Resistor Current Sensing
A typical sensing circuit using a discrete resistor is shown
in Figure 4a. RSENSE is chosen based on the required
output current.
The current comparator has a maximum threshold
VSENSE(MAX) determined by the ILIM setting. The current
comparator threshold voltage sets the peak of the inductor current, yielding a maximum average output current,
IMAX, equal to the peak value less half the peak-to-peak
ripple current, ΔIL. To calculate the sense resistor value,
use the equation:
RSENSE =
VSENSE(MAX)
ΔI
IMAX + L
2
When using the controller in very low dropout conditions,
the maximum output current level will be reduced due to
the internal compensation required to meet stability criterion for buck regulators operating at greater than 50%
duty factor. A curve is provided in the Typical Performance
Characteristics section to estimate this reduction in peak
output current depending upon the operating duty factor.
38582f
16
LTC3858-2
APPLICATIONS INFORMATION
Inductor DCR Sensing
For applications requiring the highest possible efficiency
at high load currents, the LTC3850 is capable of sensing
the voltage drop across the inductor DCR, as shown in
Figure 4b. The DCR of the inductor represents the small
amount of DC resistance of the copper wire, which can be
less than 1mΩ for today’s low value, high current inductors.
In a high current application requiring such an inductor,
power loss through a sense resistor would cost several
points of efficiency compared to inductor DCR sensing.
If the external R1||R2 • C1 time constant is chosen to be
exactly equal to the L/DCR time constant, the voltage drop
across the external capacitor is equal to the drop across
the inductor DCR multiplied by R2/(R1 + R2). R2 scales the
voltage across the sense terminals for applications where
the DCR is greater than the target sense resistor value.
To properly dimension the external filter components, the
DCR of the inductor must be known. It can be measured
using a good RLC meter, but the DCR tolerance is not
always the same and varies with temperature; consult
the manufacturers’ data sheets for detailed information.
Using the inductor ripple current value from the Inductor
Value Calculation section, the target sense resistor value is:
RSENSE(EQUIV) =
VSENSE(MAX)
ΔI
IMAX + L
2
To ensure that the application will deliver full load current
over the full operating temperature range, choose the
minimum value for the Maximum Current Sense Threshold Voltage (VSENSE(MAX)) in the Electrical Characteristics
table (30mV, 50mV or 75mV depending on the state of
the ILIM pin).
Next, determine the DCR of the inductor. When provided,
use the manufacturer’s maximum value, usually given at
20°C. Increase this value to account for the temperature
coefficient of copper, which is approximately 0.4%/°C. A
conservative value for TL(MAX) is 100°C.
To scale the maximum inductor DCR to the desired sense
resistor (RD) value, use the divider ratio:
RD =
RSENSE(EQUIV)
DCRMAX at TL(MAX)
VIN
INTVCC
VIN
BOOST
BOOST
INDUCTOR
TG
TG
VIN
INTVCC
VIN
RSENSE
VOUT
SW
LTC3858-2
BG
SENSE
PLACE CAPACITOR NEAR
SENSE PINS
DCR
VOUT
R1
SENSE+
SENSE+
–
L
SW
LTC3858-2
BG
C1*
R2
SENSE–
SGND
SGND
38582 F04a
(4a) Using a Resistor to Sense Current
*PLACE C1 NEAR
SENSE PINS
(R1||R2) t C1 =
L
DCR
RSENSE(EQ) = DCR
R2
R1 + R2
38582 F04b
(4b) Using the Inductor DCR to Sense Current
Figure 4. Current Sensing Methods
38582f
17
LTC3858-2
APPLICATIONS INFORMATION
C1 is usually selected to be in the range of 0.1μF to 0.47μF.
This forces R1||R2 to around 2k, reducing error that might
have been caused by the SENSE+ pin’s ±1μA current.
The equivalent resistance R1||R2 is scaled to the room
temperature inductance and maximum DCR:
R1|| R2 =
L
(DCR at 20°C) • C1
The sense resistor values are:
R1=
R1|| R2
R1• RD
; R2 =
1– RD
RD
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at the maximum input
voltage:
PLOSS R1=
( VIN(MAX) – VOUT ) • VOUT
R1
Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider
this power loss when deciding whether to use inductor
DCR sensing or sense resistors. Light load power loss
can be modestly higher with a DCR network than with a
sense resistor, due to the extra switching losses incurred
through R1. However, DCR sensing eliminates a sense
resistor, reduces conduction losses and provides higher
efficiency at heavy loads. Peak efficiency is about the same
with either method.
Inductor Value Calculation
The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use
of smaller inductor and capacitor values. So why would
anyone ever choose to operate at lower frequencies with
larger components? The answer is efficiency. A higher
frequency generally results in lower efficiency because
of MOSFET gate charge losses. In addition to this basic
trade-off, the effect of inductor value on ripple current and
low current operation must also be considered.
The inductor value has a direct effect on ripple current. The
inductor ripple current ΔIL decreases with higher inductance or higher frequency and increases with higher VIN:
ΔIL =
⎛ V ⎞
1
VOUT ⎜1– OUT ⎟
VIN ⎠
( f) (L)
⎝
Accepting larger values of ΔIL allows the use of low
inductances, but results in higher output voltage ripple
and greater core losses. A reasonable starting point for
setting ripple current is ΔIL = 0.3(IMAX). The maximum
ΔIL occurs at the maximum input voltage.
The inductor value also has secondary effects. The transition to Burst Mode operation begins when the average
inductor current required results in a peak current below
30% of the current limit determined by RSENSE. Lower
inductor values (higher ΔIL) will cause this to occur at
lower load currents, which can cause a dip in efficiency in
the upper range of low current operation. In Burst Mode
operation, lower inductance values will cause the burst
frequency to decrease.
Inductor Core Selection
Once the value for L is known, the type of inductor must
be selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite or molypermalloy
cores. Actual core loss is independent of core size for a
fixed inductor value, but it is very dependent on inductance
value selected. As inductance increases, core losses go
down. Unfortunately, increased inductance requires more
turns of wire and therefore copper losses will increase.
Ferrite designs have very low core loss and are preferred
for high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite
core material saturates “hard,” which means that inductance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
38582f
18
LTC3858-2
APPLICATIONS INFORMATION
Power MOSFET and Schottky Diode (Optional)
Selection
Two external power MOSFETs must be selected for each
controller in the LTC3858-2: one N-channel MOSFET for
the top (main) switch, and one N-channel MOSFET for the
bottom (synchronous) switch.
The peak-to-peak drive levels are set by the INTVCC voltage.
This voltage is typically 5.2V during start-up (see EXTVCC
Pin Connection). Consequently, logic-level threshold
MOSFETs must be used in most applications. The only
exception is if low input voltage is expected (VIN < 4V);
then, sub-logic level threshold MOSFETs (VGS(TH) < 3V)
should be used. Pay close attention to the BVDSS specification for the MOSFETs as well; many of the logic-level
MOSFETs are limited to 30V or less.
Selection criteria for the power MOSFETs include the
on-resistance, RDS(ON), Miller capacitance, CMILLER, input
voltage and maximum output current. Miller capacitance,
CMILLER, can be approximated from the gate charge curve
usually provided on the MOSFET manufacturers’ data
sheet. CMILLER is equal to the increase in gate charge
along the horizontal axis while the curve is approximately
flat divided by the specified change in VDS. This result is
then multiplied by the ratio of the application applied VDS
to the gate charge curve specified VDS. When the IC is
operating in continuous mode the duty cycles for the top
and bottom MOSFETs are given by:
Main Switch Duty Cycle =
VOUT
VIN
Synchronous Switch Duty Cycle =
VIN − VOUT
VIN
The MOSFET power dissipations at maximum output
current are given by:
PMAIN =
VOUT
(IMAX )2 (1+ δ) RDS(ON) +
VIN
⎛I
⎞
⎝ 2 ⎠
( VIN )2 ⎜ MAX ⎟ (RDR ) (CMILLER ) •
⎡
1
1 ⎤
+
⎢
⎥( f)
⎣ VINTVCC – VTHMIN VTHMIN ⎦
PSYNC =
VIN – VOUT
(IMAX )2 (1+ δ) RDS(ON)
VIN
where δ is the temperature dependency of RDS(ON) and
RDR (approximately 2Ω) is the effective driver resistance
at the MOSFET’s Miller threshold voltage. VTHMIN is the
typical MOSFET minimum threshold voltage.
Both MOSFETs have I2R losses while the topside N-channel
equation includes an additional term for transition losses,
which are highest at high input voltages. For VIN < 20V
the high current efficiency generally improves with larger
MOSFETs, while for VIN > 20V the transition losses rapidly
increase to the point that the use of a higher RDS(ON) device
with lower CMILLER actually provides higher efficiency. The
synchronous MOSFET losses are greatest at high input
voltage when the top switch duty factor is low or during
a short-circuit when the synchronous switch is on close
to 100% of the period.
The term (1+ δ) is generally given for a MOSFET in the
form of a normalized RDS(ON) vs Temperature curve, but
δ = 0.005/°C can be used as an approximation for low
voltage MOSFETs.
The optional Schottky diodes D3 and D4 shown in Figure 13
conduct during the dead-time between the conduction of
the two power MOSFETs. This prevents the body diode of
the bottom MOSFET from turning on, storing charge during
the dead-time and requiring a reverse recovery period that
could cost as much as 3% in efficiency at high VIN. A 1A
to 3A Schottky is generally a good compromise for both
regions of operation due to the relatively small average
current. Larger diodes result in additional transition losses
due to their larger junction capacitance.
38582f
19
LTC3858-2
APPLICATIONS INFORMATION
CIN and COUT Selection
The selection of CIN is simplified by the 2-phase architecture and its impact on the worst-case RMS current drawn
through the input network (battery/fuse/capacitor). It can be
shown that the worst-case capacitor RMS current occurs
when only one controller is operating. The controller with
the highest (VOUT)(IOUT) product needs to be used in the
formula shown in Equation 1 to determine the maximum
RMS capacitor current requirement. Increasing the output current drawn from the other controller will actually
decrease the input RMS ripple current from its maximum
value. The out-of-phase technique typically reduces the
input capacitor’s RMS ripple current by a factor of 30%
to 70% when compared to a single phase power supply
solution.
In continuous mode, the source current of the top MOSFET
is a square wave of duty cycle (VOUT)/(VIN). To prevent
large voltage transients, a low ESR capacitor sized for the
maximum RMS current of one channel must be used. The
maximum RMS capacitor current is given by:
CIN Required IRMS ≈
IMAX
VIN
⎡⎣( VOUT ) ( VIN – VOUT )⎤⎦1/ 2 (1)
Equation 1 has a maximum at VIN = 2VOUT , where IRMS
= IOUT/2. This simple worst-case condition is commonly
used for design because even significant deviations do not
offer much relief. Note that capacitor manufacturers’ ripple
current ratings are often based on only 2000 hours of life.
This makes it advisable to further derate the capacitor, or
to choose a capacitor rated at a higher temperature than
required. Several capacitors may be paralleled to meet
size or height requirements in the design. Due to the high
operating frequency of the LTC3858-2, ceramic capacitors
can also be used for CIN. Always consult the manufacturer
if there is any question.
The benefit of 2-phase operation can be calculated by
using Equation 1 for the higher power controller and
then calculating the loss that would have resulted if both
controller channels switched on at the same time. The
total RMS power lost is lower when both controllers are
operating due to the reduced overlap of current pulses
required through the input capacitor’s ESR. This is why
the input capacitor’s requirement calculated above for the
worst-case controller is adequate for the dual controller
design. Also, the input protection fuse resistance, battery
resistance, and PC board trace resistance losses are also
reduced due to the reduced peak currents in a 2-phase
system. The overall benefit of a multiphase design will
only be fully realized when the source impedance of the
power supply/battery is included in the efficiency testing.
The drains of the top MOSFETs should be placed within
1cm of each other and share a common CIN (s). Separating the sources and CIN may produce undesirable voltage
and current resonances at VIN.
A small (0.1μF to 1μF) bypass capacitor between the chip
VIN pin and ground, placed close to the LTC3858-2, is also
suggested. A small (1Ω to 10Ω) resistor placed between
CIN (C1) and the VIN pin provides further isolation between
the two channels.
The selection of COUT is driven by the effective series
resistance (ESR). Typically, once the ESR requirement
is satisfied, the capacitance is adequate for filtering. The
output ripple (ΔVOUT) is approximated by:
⎛
⎞
1
ΔVOUT ≈ ΔIL ⎜ESR +
⎟
8 • f • COUT ⎠
⎝
where fO is the operating frequency, COUT is the output
capacitance and ΔIL is the ripple current in the inductor.
The output ripple is highest at maximum input voltage
since ΔIL increases with input voltage.
38582f
20
LTC3858-2
APPLICATIONS INFORMATION
Setting Output Voltage
Soft-Start (SS Pins)
The LTC3858-2 output voltages are each set by an external feedback resistor divider carefully placed across the
output, as shown in Figure 5. The regulated output voltage
is determined by:
The start-up of each VOUT is controlled by the voltage on
the respective SS pin. When the voltage on the SS pin
is less than the internal 0.8V reference, the LTC3858-2
regulates the VFB pin voltage to the voltage on the SS
pin instead of 0.8V. The SS pin can be used to program
an external soft-start function or to allow VOUT to track
another supply during start-up.
⎛ R ⎞
VOUT = 0.8V ⎜1+ B ⎟
⎝ RA ⎠
To improve the frequency response, a feedforward capacitor, CFF , may be used. Great care should be taken to
route the VFB line away from noise sources, such as the
inductor or the SW line.
VOUT
1/2 LTC3858-2
RB
CFF
Soft-start is enabled by simply connecting a capacitor from
the SS pin to ground, as shown in Figure 6. An internal
1μA current source charges the capacitor, providing a
linear ramping voltage at the SS pin. The LTC3858-2 will
regulate the VFB pin (and hence VOUT) according to the
voltage on the SS pin, allowing VOUT to rise smoothly from
0V to its final regulated value. The total soft-start time will
be approximately:
VFB
RA
38582 F05
tSS = CSS •
0.8V
1μA
Figure 5. Setting Output Voltage
1/2 LTC3858-2
SS
CSS
SGND
38582 F06
Figure 6. Using the SS Pin to Program Soft-Start
38582f
21
LTC3858-2
APPLICATIONS INFORMATION
Alternatively, the SS pin can be used to track two (or
more) supplies during start-up, as shown qualitatively in
Figures 7a and 7b. To do this, a resistor divider should
be connected from the master supply (VX) to the SS
pin of the slave supply (VOUT), as shown in Figure 8. During start-up, VOUT will track VX according to the ratio set
by the resistor divider:
+ RTRACKB
R
VX
RA
=
• TRACKA
VOUT RTRACKA
RA + RB
For coincident tracking (VOUT = VX during start-up):
RA = RTRACKA
RB = RTRACKB
VX(MASTER)
OUTPUT VOLTAGE
OUTPUT VOLTAGE
VX(MASTER)
VOUT(SLAVE)
VOUT(SLAVE)
38582 F07a
38582 F07b
TIME
TIME
(7a) Coincident Tracking
(7b) Ratiometric Tracking
Figure 7. Two Different Modes of Output Voltage Tracking
Vx VOUT
RB
1/2 LTC3858-2
VFB
RA
RTRACKB
SS
RTRACKA
38582 F08
Figure 8. Using the SS Pin for Tracking
38582f
22
LTC3858-2
APPLICATIONS INFORMATION
INTVCC Regulators
The LTC3858-2 features two separate internal P-channel
low dropout linear regulators (LDO) that supply power at
the INTVCC pin from either the VIN supply pin or the EXTVCC pin depending on the connection of the EXTVCC pin.
INTVCC powers the gate drivers and much of the internal
circuitry. The VIN LDO and the EXTVCC LDO regulate INTVCC to 5.1V. Each of these can supply a peak current of
50mA and must be bypassed to ground with a minimum
of 4.7μF low ESR capacitor. Regardless of what type of
bulk capacitor is used, an additional 1μF ceramic capacitor
placed directly adjacent to the INTVCC and PGND pins is
highly recommended. Good bypassing is needed to supply
the high transient currents required by the MOSFET gate
drivers and to prevent interaction between the channels.
High input voltage applications in which large MOSFETs
are being driven at high frequencies may cause the maximum junction temperature rating for the LTC3858-2 to be
exceeded. The INTVCC current, which is dominated by the
gate charge current, may be supplied by either the VIN LDO
or the EXTVCC LDO. When the voltage on the EXTVCC pin
is less than 4.7V, the VIN LDO is enabled. Power dissipation for the IC in this case is highest and is equal to VIN •
IINTVCC. The gate charge current is dependent on operating
frequency as discussed in the Efficiency Considerations
section. The junction temperature can be estimated by
using the equations given in Note 3 of the Electrical Characteristics. For example, the LTC3858-2 INTVCC current
is limited to less than 32mA from a 40V supply when not
using the EXTVCC supply at 70°C ambient temperature:
TJ = 70°C + (32mA)(40V)(43°C/W) = 125°C
To prevent the maximum junction temperature from being exceeded, the input supply current must be checked
while operating in forced continuous mode (PLLIN/MODE
= INTVCC) at maximum VIN.
When the voltage applied to EXTVCC rises above 4.7V, the
VIN LDO is turned off and the EXTVCC LDO is enabled. The
EXTVCC LDO remains on as long as the voltage applied to
EXTVCC remains above 4.5V. The EXTVCC LDO attempts
to regulate the INTVCC voltage to 5.1V, so while EXTVCC
is less than 5.1V, the LDO is in dropout and the INTVCC
voltage is approximately equal to EXTVCC. When EXTVCC
is greater than 5.1V, up to an absolute maximum of 14V,
INTVCC is regulated to 5.1V.
Using the EXTVCC LDO allows the MOSFET driver and
control power to be derived from one of the switching
regulator outputs (4.7V ≤ VOUT ≤ 14V) during normal
operation and from the VIN LDO when the output is out
of regulation (e.g., start-up, short-circuit). If more current
is required through the EXTVCC LDO than is specified, an
external Schottky diode can be added between the EXTVCC
and INTVCC pins. In this case, do not apply more than
6V to the EXTVCC pin and make sure that EXTVCC ≤ VIN.
Significant efficiency and thermal gains can be realized
by powering INTVCC from the output, since the VIN current resulting from the driver and control currents will be
scaled by a factor of (Duty Cycle)/(Switcher Efficiency).
For 5V to 14V regulator outputs, this means connecting
the EXTVCC pin directly to VOUT . Tying the EXTVCC pin to
an 8.5V supply reduces the junction temperature in the
previous example from 125°C to:
TJ = 70°C + (32mA)(8.5V)(43°C/W) = 82°C
However, for 3.3V and other low voltage outputs, additional
circuitry is required to derive INTVCC power from the output.
The following list summarizes the four possible connections for EXTVCC:
1. EXTVCC Grounded. This will cause INTVCC to be powered
from the internal 5.1V regulator resulting in an efficiency
penalty of up to 10% at high input voltages.
2. EXTVCC Connected Directly to VOUT . This is the normal
connection for a 5V to 14V regulator and provides the
highest efficiency.
3. EXTVCC Connected to an External Supply. If an external
supply is available in the 5V to 14V range, it may be
used to power EXTVCC. Ensure that EXTVCC < VIN.
4. EXTVCC Connected to an Output-Derived Boost Network.
For 3.3V and other low voltage regulators, efficiency
gains can still be realized by connecting EXTVCC to an
output-derived voltage that has been boosted to greater
than 4.7V. This can be done with the capacitive charge
pump shown in Figure 9. Ensure that EXTVCC < VIN.
38582f
23
LTC3858-2
APPLICATIONS INFORMATION
VIN
CIN
BAT85
VIN
BAT85
MTOP
VN2222LL
TG1
1/2 LTC3858-2
EXTVCC
L
BAT85
RSENSE
VOUT
SW
MBOT
BG1
PGND
COUT
D
38582 F09
Figure 9. Capacitive Charge Pump for EXTVCC
tions with very low duty cycles, the LTC3858-2 will begin
cycle skipping in order to limit the short-circuit current.
In this situation the bottom MOSFET will be dissipating
most of the power but less than in normal operation. The
short-circuit ripple current is determined by the minimum
on-time, tON(MIN), of the LTC3858-2 (≈95ns), the input
voltage and inductor value:
⎛V ⎞
ΔI L(SC) = tON(MIN) ⎜ IN ⎟
⎝ L ⎠
The resulting average short-circuit current is:
ISC =
50% • ILIM(MAX)
RSENSE
1
– ΔIL(SC)
2
Topside MOSFET Driver Supply (CB, DB)
Phase-Locked Loop and Frequency Synchronization
External bootstrap capacitors, CB, connected to the BOOST
pins supply the gate drive voltages for the topside MOSFETs.
Capacitor CB in the Functional Diagram is charged though
external diode DB from INTVCC when the SW pin is low.
When one of the topside MOSFETs is turned on, the driver
places the CB voltage across the gate-source of the desired
MOSFET. This enhances the top MOSFET switch and turns
it on. The switch node voltage, SW, rises to VIN and the
BOOST pin follows. With the topside MOSFET on, the
boost voltage is above the input supply: VBOOST = VIN +
VINTVCC. The value of the boost capacitor, CB, needs to be
100 times that of the total input capacitance of the topside MOSFET(s). The reverse breakdown of the external
Schottky diode must be greater than VIN(MAX).
The LTC3858-2 has an internal phase-locked loop (PLL)
comprised of a phase frequency detector, a lowpass filter,
and a voltage-controlled oscillator (VCO). This allows the
turn-on of the top MOSFET of controller 1 to be locked to
the rising edge of an external clock signal applied to the
PLLIN/MODE pin. The turn-on of controller 2’s top MOSFET
is thus 180 degrees out of phase with the external clock.
The phase detector is an edge sensitive digital type that
provides zero degrees phase shift between the external
and internal oscillators. This type of phase detector does
not exhibit false lock to harmonics of the external clock.
When adjusting the gate drive level, the final arbiter is the
total input current for the regulator. If a change is made
and the input current decreases, then the efficiency has
improved. If there is no change in input current, then there
is no change in efficiency.
Fault Conditions: Current Limit and Current Foldback
When the output current hits the current limit, the output
voltage begins to drop. If the output voltage falls below
70% of its nominal output level, then the maximum
sense voltage is progressively lowered to about half of
its maximum selected value. Under short-circuit condi-
When not prebiased, applying an external clock will invoke
traditional PLL operation. If the external clock frequency is
greater than the internal oscillator’s frequency, fOSC, then
current is sourced continuously from the phase detector
output, pulling up the VCO input. When the external clock
frequency is less than fOSC, current is sunk continuously,
pulling down the VCO input. If the external and internal
frequencies are the same but exhibit a phase difference,
the current sources turn on for an amount of time corresponding to the phase difference. The voltage at the
VCO input is adjusted until the phase and frequency of
the internal and external oscillators are identical. At the
stable operating point, the phase detector output is high
impedance and the internal filter capacitor, CLP , holds the
voltage at the VCO input.
38582f
24
LTC3858-2
APPLICATIONS INFORMATION
Table 3 summarizes the different states in which the FREQ
pin can be used.
1000
900
FREQUENCY (kHz)
800
Table 3
700
FREQ PIN
PLLIN/MODE PIN
FREQUENCY
0V
DC Voltage
350kHz
400
INTVCC
DC Voltage
535kHz
300
Resistor
DC Voltage
50kHz to 900kHz
200
Any of the Above
External Clock
Phase-Locked to
External Clock
600
500
100
0
15 25 35 45 55 65 75 85 95 105 115 125
FREQ PIN RESISTOR (kΩ)
38582 F10
Figure 10. Relationship Between Oscillator Frequency
and Resistor Value at the FREQ Pin
Note that the LTC3858-2 can only be synchronized to an
external clock whose frequency is within range of the
LTC3858-2’s internal VCO, which is nominally 55kHz to
1MHz. This is guaranteed to be between 75kHz and 850kHz.
Typically, the external clock (on the PLLIN/MODE pin) input
high threshold is 1.6V, while the input low threshold is 1.1V.
Rapid phase-locking can be achieved by using the FREQ
pin to set a free-running frequency near the desired
synchronization frequency. The VCO’s input voltage is
prebiased at a frequency corresponding to the frequency
set by the FREQ pin. Once prebiased, the PLL only needs
to adjust the frequency slightly to achieve phase-locking
and synchronization. Although it is not required that the
free-running frequency be near external clock frequency,
doing so will prevent the operating frequency from passing
through a large range of frequencies as the PLL locks.
Minimum On-Time Considerations
Minimum on-time, tON(MIN), is the smallest time duration that the LTC3858-2 is capable of turning on the top
MOSFET. It is determined by internal timing delays and the
gate charge required to turn on the top MOSFET. Low duty
cycle applications may approach this minimum on-time
limit and care should be taken to ensure that:
t ON(MIN) <
VOUT
VIN ( f)
If the duty cycle falls below what can be accommodated
by the minimum on-time, the controller will begin to skip
cycles. The output voltage will continue to be regulated,
but the ripple voltage and current will increase.
The minimum on-time for the LTC3858-2 is approximately
95ns. However, as the peak sense voltage decreases the
minimum on-time gradually increases up to about 130ns.
This is of particular concern in forced continuous applications with low ripple current at light loads. If the duty cycle
drops below the minimum on-time limit in this situation,
a significant amount of cycle skipping can occur with correspondingly larger current and voltage ripple.
38582f
25
LTC3858-2
APPLICATIONS INFORMATION
Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can
be expressed as:
%Efficiency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc. are the individual losses as a percentage of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of
the losses in LTC3858-2 circuits: 1) IC VIN current, 2) INTVCC regulator current, 3) I2R losses, 4) topside MOSFET
transition losses.
1. The VIN current is the DC input supply current given
in the Electrical Characteristics table, which excludes
MOSFET driver and control currents. VIN current typically results in a small (<0.1%) loss.
2. INTVCC current is the sum of the MOSFET driver and
control currents. The MOSFET driver current results
from switching the gate capacitance of the power
MOSFETs. Each time a MOSFET gate is switched
from low to high to low again, a packet of charge, dQ,
moves from INTVCC to ground. The resulting dQ/dt is
a current out of INTVCC that is typically much larger
than the control circuit current. In continuous mode,
IGATECHG = f(QT + QB), where QT and QB are the gate
charges of the topside and bottom side MOSFETs.
Supplying INTVCC from an output-derived power source
through EXTVCC will scale the VIN current required for
the driver and control circuits by a factor of (Duty Cycle)/
(Efficiency). For example, in a 20V to 5V application,
10mA of INTVCC current results in approximately 2.5mA
of VIN current. This reduces the midcurrent loss from
10% or more (if the driver was powered directly from
VIN) to only a few percent.
3. I2R losses are predicted from the DC resistances of the
fuse (if used), MOSFET, inductor, current sense resistor, and input and output capacitor ESR. In continuous
mode the average output current flows through L and
RSENSE, but is “chopped” between the topside MOSFET
and the synchronous MOSFET. If the two MOSFETs have
approximately the same RDS(ON), then the resistance
of one MOSFET can simply be summed with the resistances of L, RSENSE and ESR to obtain I2R losses. For
example, if each RDS(ON) = 30mΩ, RL = 50mΩ, RSENSE
= 10mΩ and RESR = 40mΩ (sum of both input and
output capacitance losses), then the total resistance
is 130mΩ. This results in losses ranging from 3% to
13% as the output current increases from 1A to 5A for
a 5V output, or a 4% to 20% loss for a 3.3V output.
Efficiency varies as the inverse square of VOUT for the
same external components and output power level. The
combined effects of increasingly lower output voltages
and higher currents required by high performance digital
systems is not doubling but quadrupling the importance
of loss terms in the switching regulator system!
4. Transition losses apply only to the topside MOSFET(s),
and become significant only when operating at high
input voltages (typically 15V or greater). Transition
losses can be estimated from:
Transition Loss = (1.7) • VIN • 2 • IO(MAX) • CRSS • f
Other “hidden” losses such as copper trace and internal
battery resistances can account for an additional 5% to
10% efficiency degradation in portable systems. It is
very important to include these “system” level losses
during the design phase. The internal battery and fuse
resistance losses can be minimized by making sure that
CIN has adequate charge storage and very low ESR at
the switching frequency. A 25W supply will typically
require a minimum of 20μF to 40μF of capacitance
having a maximum of 20mΩ to 50mΩ of ESR. The
LTC3858-2 2-phase architecture typically halves this
input capacitance requirement over competing solutions. Other losses including Schottky conduction losses
during dead-time and inductor core losses generally
account for less than 2% total additional loss.
38582f
26
LTC3858-2
APPLICATIONS INFORMATION
Checking Transient Response
The regulator loop response can be checked by looking at
the load current transient response. Switching regulators
take several cycles to respond to a step in DC (resistive)
load current. When a load step occurs, VOUT shifts by an
amount equal to ΔILOAD (ESR), where ESR is the effective
series resistance of COUT . ΔILOAD also begins to charge or
discharge COUT generating the feedback error signal that
forces the regulator to adapt to the current change and
return VOUT to its steady-state value. During this recovery
time VOUT can be monitored for excessive overshoot or
ringing, which would indicate a stability problem. OPTILOOP compensation allows the transient response to be
optimized over a wide range of output capacitance and
ESR values. The availability of the ITH pin not only allows
optimization of control loop behavior, but it also provides
a DC coupled and AC filtered closed-loop response test
point. The DC step, rise time and settling at this test
point truly reflects the closed-loop response. Assuming
a predominantly second order system, phase margin and/
or damping factor can be estimated using the percentage
of overshoot seen at this pin. The bandwidth can also
be estimated by examining the rise time at the pin. The
ITH external components shown in Figure 13 circuit will
provide an adequate starting point for most applications.
The ITH series RC-CC filter sets the dominant pole-zero
loop compensation. The values can be modified slightly
(from 0.5 to 2 times their suggested values) to optimize
transient response once the final PC layout is done and
the particular output capacitor type and value have been
determined. The output capacitors need to be selected
because the various types and values determine the loop
gain and phase. An output current pulse of 20% to 80%
of full-load current having a rise time of 1μs to 10μs will
produce output voltage and ITH pin waveforms that will
give a sense of the overall loop stability without breaking
the feedback loop.
Placing a resistive load and a power MOSFET directly
across the output capacitor and driving the gate with an
appropriate signal generator is a practical way to produce
a realistic load step condition. The initial output voltage
step resulting from the step change in output current may
not be within the bandwidth of the feedback loop, so this
signal cannot be used to determine phase margin. This
is why it is better to look at the ITH pin signal which is in
the feedback loop and is the filtered and compensated
control loop response.
The gain of the loop will be increased by increasing RC
and the bandwidth of the loop will be increased by decreasing CC. If RC is increased by the same factor that CC
is decreased, the zero frequency will be kept the same,
thereby keeping the phase shift the same in the most
critical frequency range of the feedback loop. The output
voltage settling behavior is related to the stability of the
closed-loop system and will demonstrate the actual overall
supply performance.
A second, more severe transient is caused by switching
in loads with large (>1μF) supply bypass capacitors. The
discharged bypass capacitors are effectively put in parallel
with COUT , causing a rapid drop in VOUT . No regulator can
alter its delivery of current quickly enough to prevent this
sudden step change in output voltage if the load switch
resistance is low and it is driven quickly. If the ratio of
CLOAD to COUT is greater than 1:50, the switch rise time
should be controlled so that the load rise time is limited
to approximately 25 • CLOAD. Thus a 10μF capacitor would
require a 250μs rise time, limiting the charging current
to about 200mA.
38582f
27
LTC3858-2
APPLICATIONS INFORMATION
Design Example
As a design example for one channel, assume VIN =
12V(nominal), VIN = 22V (max), VOUT = 3.3V, IMAX = 5A,
VSENSE(MAX) = 75mV and f = 350kHz.
The inductance value is chosen first based on a 30% ripple
current assumption. The highest value of ripple current
occurs at the maximum input voltage. Tie the FREQ pin
to GND, generating 350kHz operation. The minimum
inductance for 30% ripple current is:
ΔIL =
VOUT ⎛ VOUT ⎞
⎟
⎜1–
( f) (L) ⎝ VIN ⎠
A 4.7μH inductor will produce 29% ripple current. The
peak inductor current will be the maximum DC value plus
one half the ripple current, or 5.73A. Increasing the ripple
current will also help ensure that the minimum on-time
of 95ns is not violated. The minimum on-time occurs at
maximum VIN:
t ON(MIN) =
VOUT
3.3V
=
= 429ns
VIN ( f) 22V (350kHz )
The equivalent RSENSE resistor value can be calculated by
using the minimum value for the maximum current sense
threshold (64mV):
RSENSE ≤
64mV
= 0.011Ω
5.73A
Choosing 0.5% resistors: RA = 24.9k and RB = 77.7k yields
an output voltage of 3.296V.
The power dissipation on the topside MOSFET can be easily
estimated. Choosing a Fairchild FDS6982S dual MOSFET
results in: RDS(ON) = 0.035Ω/0.022Ω, CMILLER = 215pF. At
maximum input voltage with T(estimated) = 50°C:
PMAIN =
3.3V
(5A )2 ⎡⎣1+ (0.005) (50°C – 25°C)⎤⎦
22V
5A
(0.035Ω) + (22V )2 (2.5Ω) (215pF ) •
2
⎡
1 ⎤
1
+
⎢⎣
⎥ (350kHz ) = 331mW
5V – 2.3V 2.3V ⎦
A short-circuit to ground will result in a folded back current of:
ISC =
32mV 1 ⎛ 95ns (22V ) ⎞
– ⎜
⎟ = 2.98A
0.015Ω 2 ⎝ 4.7μH ⎠
with a typical value of RDS(ON) and δ = (0.005/°C)(25°C)
= 0.125. The resulting power dissipated in the bottom
MOSFET is:
2
PSYNC = (2.98A ) (1.125) (0.022Ω) = 220mW
which is less than full-load conditions.
CIN is chosen for an RMS current rating of at least 3A at
temperature assuming only this channel is on. COUT is
chosen with an ESR of 0.02Ω for low output ripple voltage. The output ripple in continuous mode will be highest
at the maximum input voltage. The output voltage ripple
due to ESR is approximately:
VORIPPLE = RESR (ΔIL) = 0.02Ω(1.45A) = 29mVP-P
38582f
28
LTC3858-2
APPLICATIONS INFORMATION
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the IC. These items are also illustrated graphically in the
layout diagram of Figure 11. Figure 12 illustrates the current
waveforms present in the various branches of the 2-phase
synchronous regulators operating in the continuous mode.
Check the following in your layout:
1. Are the top N-channel MOSFETs MTOP1 and MTOP2
located within 1cm of each other with a common drain
connection at CIN? Do not attempt to split the input
decoupling for the two channels as it can cause a large
resonant loop.
2. Are the signal and power grounds kept separate? The
combined IC signal ground pin and the ground return
of CINTVCC must return to the combined COUT (–) terminals. The path formed by the top N-channel MOSFET,
Schottky diode and the CIN capacitor should have short
leads and PC trace lengths. The output capacitor (–)
terminals should be connected as close as possible
to the (–) terminals of the input capacitor by placing
the capacitors next to each other and away from the
Schottky loop described above.
3. Do the LTC3858-2 VFB pins’ resistive dividers connect to
the (+) terminals of COUT? The resistive divider must be
connected between the (+) terminal of COUT and signal
ground. The feedback resistor connections should not
be along the high current input feeds from the input
capacitor(s).
4. Are the SENSE– and SENSE+ leads routed together with
minimum PC trace spacing? The filter capacitor between
SENSE+ and SENSE– should be as close as possible
to the IC. Ensure accurate current sensing with Kelvin
connections at the SENSE resistor.
5. Is the INTVCC decoupling capacitor connected close
to the IC, between the INTVCC and the power ground
pins? This capacitor carries the MOSFET drivers’ current peaks. An additional 1μF ceramic capacitor placed
immediately next to the INTVCC and PGND pins can help
improve noise performance substantially.
6. Keep the switching nodes (SW1, SW2), top gate nodes
(TG1, TG2), and boost nodes (BOOST1, BOOST2) away
from sensitive small-signal nodes, especially from the
opposites channel’s voltage and current sensing feedback pins. All of these nodes have very large and fast
moving signals and therefore should be kept on the
“output side” of the LTC3858-2 and occupy minimum
PC trace area.
7. Use a modified “star ground” technique: a low impedance, large copper area central grounding point on
the same side of the PC board as the input and output
capacitors with tie-ins for the bottom of the INTVCC
decoupling capacitor, the bottom of the voltage feedback
resistive divider and the SGND pin of the IC.
38582f
29
LTC3858-2
APPLICATIONS INFORMATION
PC Board Layout Debugging
Start with one controller on at a time. It is helpful to use
a DC-50MHz current probe to monitor the current in the
inductor while testing the circuit. Monitor the output
switching node (SW pin) to synchronize the oscilloscope
to the internal oscillator and probe the actual output
voltage as well. Check for proper performance over the
operating voltage and current range expected in the application. The frequency of operation should be maintained
over the input voltage range down to dropout and until
the output load drops below the low current operation
threshold—typically 10% of the maximum designed
current level in Burst Mode operation.
The duty cycle percentage should be maintained from cycle
to cycle in a well-designed, low noise PCB implementation.
Variation in the duty cycle at a subharmonic rate can suggest noise pickup at the current or voltage sensing inputs
or inadequate loop compensation. Overcompensation of
the loop can be used to tame a poor PC layout if regulator
bandwidth optimization is not required. Only after each
controller is checked for its individual performance should
both controllers be turned on at the same time. A particularly
difficult region of operation is when one controller channel
is nearing its current comparator trip point when the other
channel is turning on its top MOSFET. This occurs around
50% duty cycle on either channel due to the phasing of
the internal clocks and may cause minor duty cycle jitter.
Investigate whether any problems exist only at higher output currents or only at higher input voltages. If problems
coincide with high input voltages and low output currents,
look for capacitive coupling between the BOOST, SW, TG,
and possibly BG connections and the sensitive voltage
and current pins. The capacitor placed across the current
sensing pins needs to be placed immediately adjacent to
the pins of the IC. This capacitor helps to minimize the
effects of differential noise injection due to high frequency
capacitive coupling. If problems are encountered with
high current output loading at lower input voltages, look
for inductive coupling between CIN, Schottky and the top
MOSFET components to the sensitive current and voltage
sensing traces. In addition, investigate common ground
path voltage pickup between these components and the
SGND pin of the IC.
An embarrassing problem, which can be missed in an
otherwise properly working switching regulator, results
when the current sensing leads are hooked up backwards.
The output voltage under this improper hookup will still
be maintained but the advantages of current mode control
will not be realized. Compensation of the voltage loop will
be much more sensitive to component selection. This
behavior can be investigated by temporarily shorting out
the current sensing resistor—don’t worry, the regulator
will still maintain control of the output voltage.
Reduce VIN from its nominal level to verify operation of
the regulator in dropout. Check the operation of the undervoltage lockout circuit by further lowering VIN while
monitoring the outputs to verify operation.
38582f
30
LTC3858-2
APPLICATIONS INFORMATION
RPU2
SS1
LTC3858-2
PGOOD2
ITH1
VPULL-UP
(<6V)
PGOOD2
RPU1
PGOOD1
VFB1
VPULL-UP
(<6V)
PGOOD1
L1
SENSE1+
TG1
SENSE1–
SW1
VOUT1
CB1
FREQ
PHASMD
RSENSE
M1
BOOST1
M2
D1
BG1
CLKOUT
PLLIN/MODE
RUN1
VIN
CVIN
RIN
GND
+
INTVCC
SENSE2+
BG2
VOUT1
CINTVCC
VIN
CIN
COUT2
1μF
CERAMIC
M3
BOOST2
+
EXTVCC
SENSE2–
VFB2
COUT1
PGND
RUN2
SGND
1μF
CERAMIC
+
fIN
M4
D2
CB2
ITH2
SS2
SW2
RSENSE
TG2
VOUT2
L2
38582 F11
Figure 11. Recommended Printed Circuit Layout Diagram
38582f
31
LTC3858-2
APPLICATIONS INFORMATION
SW1
L1
D1
RSENSE1
VOUT1
COUT1
RL1
VIN
RIN
CIN
SW2
BOLD LINES INDICATE
HIGH SWITCHING
CURRENT. KEEP LINES
TO A MINIMUM LENGTH.
D2
L2
RSENSE2
VOUT2
COUT2
RL2
38582 F12
Figure 12. Branch Current Waveforms
38582f
32
LTC3858-2
TYPICAL APPLICATIONS
RB1
215k
INTVCC
CF1
15pF
C1
1nF
RA1
68.1k
CITH1A
150pF
LTC3858-2
SENSE1+
PGOOD2
SENSE1–
VFB1
100k
100k
PGOOD1
SW1
ITH1
CITH1
820pF
(OPTIONAL
TRACKING)
68.1k
VOUT2
CSS2
0.1μF
COUT1
150μF
D1
VIN
SS1
ILIM
INTVCC
PHASMD
CLKOUT
PGND
PLLIN/MODE
SGND
EXTVCC
TG2
RUN1
RUN2
BOOST2
FREQ
CIN
22μF
VIN
9V TO 38V
CINT
4.7μF
D2
MTOP2
CB2
0.47μF
L2
7.2μH
SS2
RSENSE2
10mΩ
VOUT2
8.5V
COUT2 3A
150μF
SW2
ITH2
CITH2
680pF
RITH2
27k
VOUT1
3.3V
5A
MTOP1
TG1
RITH1 CSS1
15k 0.1μF
215k
RSENSE1
7mΩ
CB1
0.47μF
BOOST1
VOUT2
L1
3.3μH
MBOT1
BG1
MBOT2
BG2
CITH2A
100pF
VFB2
RA2
44.2k
SENSE2–
C2
1nF
CF2
39pF
SENSE2+
RB2
422k
38582 F13
COUT1, COUT2: SANYO 10TPD150M
L1: SUMIDA CDEP105-3R2M
L2: SUMIDA CDEP105-7R2M
MTOP1, MTOP2, MBOT1, MBOT2: VISHAY Si7848DP
Efficiency vs Output Current
Start-Up
SW Node Waveforms
100
90
EFFICIENCY (%)
80
70
VOUT = 8.5V
VOUT2
2V/DIV
VOUT = 3.3V
SW1
5V/DIV
60
50
VOUT1
2V/DIV
40
SW2
5V/DIV
30
20
10
VIN = 12V
Burst Mode OPERATION
0
0.1
0.00001 0.0001 0.001 0.01
OUTPUT CURRENT (A)
1
10
20ms/DIV
38582 F13c
1μs/DIV
38582 F13d
38582 F13b
Figure 13. High Efficiency Dual 8.5V/3.3V Step-Down Converter
38582f
33
LTC3858-2
TYPICAL APPLICATIONS
High Efficiency Dual 2.5V/3.3V Step-Down Converter
RB1
143k
CF1
22pF
RA1
68.1k
INTVCC
C1
1nF
CITH1A
100pF
LTC3858-2
SENSE1+
PGOOD2
SENSE1–
VFB1
100k
100k
PGOOD1
MBOT1
BG1
SW1
ITH1
RITH1
22k
CSS1
0.01μF
CSS2
0.01μF
D1
SS1
INTVCC
ILIM
PHASMD
PGND
CLKOUT
PLLIN/MODE
SGND
EXTVCC
TG2
RUN1
RUN2
BOOST2
FREQ
ITH2
RITH2
15k
CITH2A
150pF
COUT1
150μF
VOUT1
2.5V
5A
MTOP1
TG1
VIN
SS2
CITH2
820pF
RSENSE1
7mΩ
CB1
0.47μF
BOOST1
CITH1
820pF
L1
2.4μH
CIN
22μF
VIN
4V TO 38V
CINT
4.7μF
D2
MTOP2
CB2
0.47μF
L2
3.2μH
RSENSE2
7mΩ
SW2
BG2
VOUT2
3.3V
COUT2 5A
150μF
MBOT2
VFB2
RA2
68.1k
SENSE2–
CF2
15pF
C2
1nF
SENSE2+
RB2
215k
38582 TA02
COUT1, COUT2: SANYO 10TPD150M
L1: SUMIDA CDEP105-2R5
L2: SUMIDA CDEP105-3R2M
MTOP1, MTOP2, MBOT1, MBOT2: VISHAY Si7848DP
38582f
34
LTC3858-2
TYPICAL APPLICATIONS
High Efficiency Dual 12V/5V Step-Down Converter
RB1
422k
CF1
33pF
RA1
30.1k
C1
1nF
CITH1A
100pF
100k INTVCC
SENSE1+
PGOOD2
SENSE1–
PGOOD1
100k
MBOT1
BG1
VFB1
SW1
CITH1
680pF
CSS1
0.01μF
VOUT1
RFREQ
60k
CSS2
0.01μF
LTC3858-2
ITH2
CITH2
680pF
RITH2
17k
D1
VIN
SS1
INTVCC
ILIM
PHASMD
PGND
CLKOUT
PLLIN/MODE
SGND
EXTVCC
TG2
RUN1
RUN2
BOOST2
FREQ
SS2
CITH2A
100pF
COUT1
47μF
VOUT1
12V
3A
MTOP1
TG1
ITH1
RSENSE1
10mΩ
CB1
0.47μF
BOOST1
RITH1
33k
L1
8.8μH
CIN
22μF
VIN
12.5V TO 38V
CINT
4.7μF
D2
MTOP2
CB2
0.47μF
L2
4.3μH
RSENSE2
7mΩ
SW2
BG2
VOUT2
5V
COUT2 5A
150μF
MBOT2
VFB2
RA2
75k
SENSE2–
CF2
15pF
C2
1nF
SENSE2+
COUT1: KEMET T525D476M016E035
COUT2: SANYO 10TPD150M
L1: SUMIDA CDEP105-8R8M
L2: SUMIDA CDEP105-4R3M
MTOP1, MTOP2, MBOT1, MBOT2: VISHAY Si7848DP
RB2
393k
38582 TA03
38582f
35
LTC3858-2
TYPICAL APPLICATIONS
High Efficiency Dual 24V/5V Step-Down Converter
RB1
487k
CF1
18pF
RA1
16.9k
C1
1nF
CITH1A
100pF
100k
SENSE1+
PGOOD2
SENSE1–
PGOOD1
INTVCC
100k
VFB1
MBOT1
BG1
SW1
RITH1
46k
CSS1
0.01μF
VOUT2
RFREQ
60k
CSS2
0.01μF
ITH1
RITH2
17k
D1
VIN
SS1
INTVCC
ILIM
PHASMD
CLKOUT
PGND
PLLIN/MODE
SGND
TG2
EXTVCC
RUN1
BOOST2
RUN2
FREQ
ITH2
CITH2
680pF
MTOP1
TG1
LTC3858-2
SS2
CITH2A
100pF
RSENSE1
25mΩ
CB1
0.47μF
BOOST1
CITH1
680pF
L1
22μH
CIN
22μF
CINT
4.7μF
COUT1
22μF
=2
CERAMIC
VIN
28V TO 38V
D2
MTOP2
CB2
0.47μF
L2
4.3μH
RSENSE2
7mΩ
SW2
BG2
VOUT1
24V
1A
VOUT2
5V
COUT2 5A
150μF
MBOT2
VFB2
RA2
75k
SENSE2–
CF2
15pF
C2
1nF
SENSE2+
COUT2: SANYO 10TPD150M
L1: SUMIDA CDRH105R-220M
L2: SUMIDA CDEP105-4R3M
MTOP1, MTOP2, MBOT1, MBOT2: VISHAY Si7848DP
RB2
392k
38582 TA04
38582f
36
LTC3858-2
TYPICAL APPLICATIONS
High Efficiency Dual 1V/1.2V Step-Down Converter
RB1
28.7k
CF1
56pF
RA1
115k
C1
1nF
CITH1A
200pF
100k INTVCC
SENSE1+
PGOOD2
SENSE1–
PGOOD1
100k
VFB1
L1
MBOT1 0.47μH
BG1
SW1
CITH1
1000pF
CSS1
0.01μF
RFREQ
60k
CSS2
0.01μF
CITH2A
200pF
VIN
SS1
INTVCC
ILIM
PHASMD
CLKOUT
PGND
PLLIN/MODE
SGND
TG2
EXTVCC
RUN1
BOOST2
RUN2
FREQ
ITH2
COUT1
220μF
=2
D1
LTC3858-2
SS2
RITH2
CITH2
3.93k
1000pF
MTOP1
TG1
ITH1
RITH1
3.93k
RSENSE1
4mΩ
CB1
0.47μF
BOOST1
VOUT1
1V
8A
CIN
22μF
VIN
12V
CINT
4.7μF
D2
MTOP2
CB2
0.47μF
L2
0.47μH
RSENSE2
4mΩ
SW2
BG2
MBOT2
VOUT2
1.2V
COUT2 8A
220μF
=2
VFB2
RA2
115k
SENSE2–
CF2
56pF
C2
1nF
SENSE2+
COUT1, COUT2: SANYO 2R5TPE220M
L1: SUMIDA CDEP105-0R4
L2: SUMIDA CDEP105-0R4
MTOP1, MTOP2: RENESAS RJK0305
MBOT1, MBOT2: RENESAS RJK0328
RB2
57.6k
38582 TA05
38582f
37
LTC3858-2
TYPICAL APPLICATIONS
High Efficiency Dual 1V/1.2V Step-Down Converter with Inductor DCR Current Sensing
RB1
28.7k
CF1
56pF
RA1
115k
RS1 1.18k
C1
0.1μF
CITH1A
200pF
SENSE1+
SENSE1–
PGOOD2
100k
INTVCC
100k
PGOOD1
SW1
CITH1
1000pF
RFREQ
65k
MTOP1
TG1
ITH1
CSS1
0.01μF
RITH2
3.93k
VOUT1
1V
8A
D1
LTC3858-2
VIN
SS1
INTVCC
ILIM
PHASMD
CLKOUT
PGND
PLLIN/MODE
SGND
EXTVCC
TG2
RUN1
RUN2
BOOST2
FREQ
CIN
22μF
VIN
12V
CINT
4.7μF
D2
MTOP2
CB2
0.47μF
CSS2
0.01μF
CITH2
1000pF
COUT1
220μF
=2
CB1
0.47μF
BOOST1
RITH1
3.93k
L1
0.47μH
MBOT1
BG1
VFB1
L2
0.47μH
SS2
SW2
ITH2
BG2
MBOT2
CITH2A
220pF
VOUT2
1.2V
COUT2 8A
220μF
=2
VFB2
RA2
115k
SENSE2–
CF2
56pF
RB2
57.6k
C2
0.1μF
COUT1, COUT2: SANYO 2R5TPE220M
L1, L2: VISHAY IHL P2525CZERR47M06
MTOP1, MTOP2: RENESAS RJK0305
MBOT1, MBOT2: RENESAS RJK0328
SENSE2+
RS2
1.18k
38582 TA06
38582f
38
LTC3858-2
PACKAGE DESCRIPTION
UH Package
32-Lead Plastic QFN (5mm × 5mm)
(Reference LTC DWG # 05-08-1693 Rev D)
0.70 p0.05
5.50 p0.05
4.10 p0.05
3.45 p 0.05
3.50 REF
(4 SIDES)
3.45 p 0.05
PACKAGE OUTLINE
0.25 p 0.05
0.50 BSC
RECOMMENDED SOLDER PAD LAYOUT
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
5.00 p 0.10
(4 SIDES)
BOTTOM VIEW—EXPOSED PAD
0.75 p 0.05
R = 0.05
TYP
0.00 – 0.05
PIN 1 NOTCH R = 0.30 TYP
OR 0.35 s 45o CHAMFER
R = 0.115
TYP
31 32
0.40 p 0.10
PIN 1
TOP MARK
(NOTE 6)
1
2
3.50 REF
(4-SIDES)
3.45 p 0.10
3.45 p 0.10
(UH32) QFN 0406 REV D
0.200 REF
NOTE:
1. DRAWING PROPOSED TO BE A JEDEC PACKAGE OUTLINE
M0-220 VARIATION WHHD-(X) (TO BE APPROVED)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
0.25 p 0.05
0.50 BSC
38582f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
39
LTC3858-2
TYPICAL APPLICATION
High Efficiency 2-Phase 12V/150W Step-Down Converter
RB1
698k
CF1
10pF
RA1
49.9k
SENSE1+
C1
1nF
SENSE1–
CITH1A
68pF
100k
INTVCC
PGOOD2
100k
PGOOD1
VFB1
MBOT1
BG1
CITH1
3300pF
VOUT
SS1
ITH1
VFB1
VIN
SS1
INTVCC
ILIM
PHASMD
CLKOUT
PGND
PLLIN/MODE
SGND
TG2
EXTVCC
RUN1
BOOST2
RUN2
FREQ
SW2
SS2
CIN
10μF
50V
CINT
4.7μF
10μF
50V
VIN
19V TO 28V
D2
MTOP2
CB2
0.47μF
L2
6μH
RSENSE2
5mΩ
COUT2
22μF
16V
MBOT2
BG2
VFB2
SENSE2–
C2
1nF
MTOP1
COUT1
22μF
16V
VOUT
12V
12.5A
D1
LTC3858-2
ITH2
RSENSE1
5mΩ
CB1
0.47μF
TG1
ITH1
CSS1
0.1μF
10μF
16V
SW1
BOOST1
RITH1
2.94k
L1
6μH
SENSE2+
10μF
16V
COUT1, COUT2: SANYO 16TQC22M
L1, L2: SUMIDA CDEP106-6ROM
MTOP1, MTOP2: INFINEON BSZ097N04LS
MBOT1, MBOT2: INFINEON BSZ097N04LS
38582 TA07
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC3859
Low IQ, Triple Output Buck/Buck/Boost Synchronous Outputs (≥5V) Remain in Regulation Through Cold Crank 2.5V ≤ VIN ≤ 38V,
DC/DC Controller
VOUT(BUCKS) Up to 24V, VOUT(BOOST) Up to 60V, IQ = 55μA,
LTC3868/LTC3868-1 Low IQ, Dual Output 2-Phase Synchronous StepDown DC/DC Controllers with 99% Duty Cycle
Phase-Lockable Fixed Operating Frequency 50kHz to 900kHz,
4V ≤ VIN ≤ 24V, 0.8V ≤ VOUT ≤ 14V, IQ = 170μA
LTC3857/LTC3857-1 Low IQ, Dual Output 2-Phase Synchronous StepDown DC/DC Controllers with 99% Duty Cycle
Phase-Lockable Fixed Operating Frequency 50kHz to 900kHz,
4V≤ VIN ≤ 38V, 0.8V ≤ VOUT ≤ 24V, IQ = 50μA,
LTC3890/LTC3890-1 60V, Low IQ, Dual 2-Phase Synchronous Step-Down
DC/DC Controller with 99% Duty Cycle
Phase-Lockable Fixed Operating Frequency 50kHz to 900kHz,
4V ≤ VIN ≤ 60V, 0.8V ≤ VOUT ≤ 24V, IQ = 50μA,
LTC3834/LTC3834-1 Low IQ, Synchronous Step-Down DC/DC Controllers Phase-Lockable Fixed Operating Frequency 140kHz to 650kHz,
4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 10V, IQ = 30μA,
LTC3835/LTC3835-1 Low IQ, Synchronous Step-Down DC/DC Controllers Phase-Lockable Fixed Operating Frequency 140kHz to 650kHz,
4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 10V, IQ = 80μA,
LTC3891
60V, Low IQ, Synchronous Step-Down DC/DC
Controller with 99% Duty Cycle
Phase-Lockable Fixed Operating Frequency 50kHz to 900kHz,
4V ≤ VIN ≤ 60V, 0.8V ≤ VOUT ≤ 24V, IQ = 50μA,
LTC3824
Low IQ, High Voltage DC/DC Controller, 100% Duty
Cycle
Selectable Fixed 200kHz to 600kHz Operating Frequency 4V ≤ VIN ≤ 60V,
0.8V ≤ VOUT ≤ VIN, IQ = 40μA, MSOP-10E
38582f
40 Linear Technology Corporation
LT 1110 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507 ● www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2010
Similar pages