IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz FEATURES GENERAL DESCRIPTION This document describes the specification for the IDTF1701 Zero-DistortionTM Lowband RF to IF Single Downconverting Mixer. This device is part of a series of mixers using lowside or highside LO injection options for all UTRA frequency bands. See the Part# Matrix for the detail of all devices in this series. The F1701 single channel device is designed to operate with a single 5V supply. It is optimized for operation in a Multi-mode, Multi-carrier BaseStation Receiver over the frequency range from 600MHz to 1060MHz using either lowside or highside LO. IF frequencies from 70MHz to 300MHz are supported. Nominally, the device offers +43dBm Output IP3 using HS LO with 184mA of ICC. DEVICE BLOCK DIAGRAM COMPETITIVE ADVANTAGE In typical basestation receivers, the RF to IF mixer dominates the linearity performance for the entire receive system. The Zero-DistortionTM family of mixers dramatically improve the maximum signal levels (IM3 tones) that the BTS can withstand at a desired Signal to Noise Ratio (SNR.) Zero-DistortionTM technology allows realization of either benefit. In basestation transmitters, digital pre-distortion (DPD) is employed to improve the Transmitter performance. By utilizing an ultra-linear mixer in the DPD RX path, such as the IDTF1701, the ACLR and/or power consumption of the full Tx system can be improved significantly. This is because the F1701 can directly drive an ADC through an Anti-Alias filter. Downstream amplification is not necessary in the DPD application. IP3O: 9 dB Dissipation: 14% Allows for higher RF gain improving Sensitivity Eliminates the need for an ADC driver or IF VGA in DPD linearization path Ideal for Multi-Carrier Systems Lowside or Highside LO 11.8dB Gain Ultra linear +43dBm IP3O using HS LO or +42dBm IP3O using LS LO 9.2dB NF 200 Ω output impedance Wide flat performance IF BW Drives ADC directly for DPD applications Low Power Consumption 5x5 20 pin package Standby Mode RF IFOUT STBY LO Bias Control ISET VCC ORDERING INFORMATION Omit IDT prefix Tape & Reel 0.8 mm height package IDTF1701NBGI8 RF product Line Green Industrial Temp range PART# MATRIX Part# RF Range UTRA bands IF freq range Typ. Gain Injection F1701 600 - 1060 5,6,8,12,13,14,17,1 8,19,20, 26 70 - 300 11.8 Both F1751 1400 - 2500 1,2,3,4,9,10,11, 21,23,24,25,33,34, 35,36,37,39, 40 50 - 500 11.8 Both F1763 2000 - 2900 7,38,40,41 50 - 500 11.7 Both IDT Zero-DistortionTM Mixer 1 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz ABSOLUTE MAXIMUM RATINGS VCC to GND STBY IF_OUT+, IF_OUT-, RF_IN LO_IN IF_SET to GND, IF_BIAS to GND RF Input Power Continuous Power Dissipation θJA (Junction – Ambient) θJC (Junction – Case) The Case is defined as the exposed paddle Operating Temperature Range (Case Temperature) Maximum Junction Temperature Storage Temperature Range Lead Temperature (soldering, 10s) -0.3V to +5.5V -0.3V to (VCC + 0.3V) -0.3V to (VCC + 0.3V) -0.3V to +0.3V -0.3V to +1.2V +20dBm 1.3W +40°C/W +3°C/W TC = -40°C to +105°C 150°C -65°C to +150°C +260°C Stresses above those listed above may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. IDT Zero-DistortionTM Mixer 2 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz IDTF1701 RECOMMENDED OPERATING CONDITIONS Parameter Comment Symbol min Supply Voltage(s) All VCC pins VCC Operating Temperature Range Case Temperature RF Freq Range Oversample RF Range max Units 4.75 5.25 V TCASE -40 +105 degC Sets LO freq range FRF1 698 960 FRF2 600 1060 630 1260 70 300 Measure gain at 200MHz IF FLO = 800MHz, 1260MHz LO Freq Range IF Freq Range IDT Zero-DistortionTM Mixer Sets LO freq range FIF 3 typ MHz RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz IDTF1701 SPECIFICATION Refer to Typical Application Circuit when operated with VCC = +5.0V, TC= +25°C, FRF = 950 MHz, FIF = 200 MHz, FLO = 1150 MHz, PLO = 0 dBm, output power = +1dBm per tone, STBY = GND unless otherwise noted. Transformer loss is de-embedded unless otherwise noted. Parameter Comment Logic Input High For Standby Pin Symbol min VIH 2 Logic Input Low For Standby Pin VIL Logic Current For Standby Pin IIH, IIL Supply Current Total VCC ISUPP Supply Current Standby Mode ISTBY STBY = VIH LO Power PLO Settling Time Pin = -13 dBm Gate STBY from VIH to VIL Time for IF Signal to settle to within 1 dB of final value Gain typ max units V 0.8 1 V +1 μA 184 210 mA 20 25 mA +3 dBm -1 -32 TSETT 130 FRF = 600MHz FLO = 800MHz GLB 11.3 FRF = 950MHz FLO = 1150MHz GMB FRF = 1060MHz FLO = 1260MHz GHB 11.4 NF 9.2 dB 17.5 dB Noise Figure 10.9 11.8 nsec 12.6 dB NF w/Blocker -100 MHz offset blocker PBLKR = +4 dBm NFBLK FRF1 = 950MHz FLO = 1150MHz PIN = -10dBm per tone 5MHz Tone Separation IP3oHSLO Output IP3 FRF1 = 950MHz FLO = 750MHz PIN = -10dBm per tone 5MHz Tone Separation IP3oLSLO 42 2RF – 2LO rejection PRF = -10dBm Frequency = 1050MHz 2x2 -77 -72 dBc 2nd Harmonic Pout = -3dBm H2 -78 -72 dBc IDT Zero-DistortionTM Mixer 36 43 dBm 4 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz IDTF1701 SPECIFICATION - CONTINUED Refer to Typical Application Circuit when operated with VCC = +5.0V, TC= +25°C, FRF = 950 MHz, FIF = 200 MHz, FLO = 1150 MHz, PLO = 0 dBm, output power = +1dBm per tone, STBY = GND unless otherwise noted. Transformer loss is de-embedded unless otherwise noted. IM2 Sum Product (IM2+) IM2 Diff Product (IM2-) Pout = -3 dBm each tone FIF1 = 200 MHz, FIF2 = 205 MHz IM2 Product = 405 MHz IM2+ -75 -69 dBc Pout = -3 dBm each tone FIF1 = 200 MHz, FIF2 = 205 MHz IM2 Product = 5 MHz IM2- -80 -75 dBc 1dB output compression Output referred P1dBO 1dB input compression Input referred Gain Comp. w/blocker Gain Ripple Unmodulated blocker Pin = -4 dBm, -100MHz offset Signal Pin Tone = -20dBm Measure Δ gain of signal 17 21 dBm P1dBI 10.2 dBm ΔGAC 0.1 0.15 dB 1 1.2 dB Fixed LO = 1100 MHz RF = 770 to 1050 MHz IF = 50 to 330 MHz RF Input Impedance Single Ended ZRF 50 LO port Impedance Single Ended ZLO 50 IF Output Impedance Differential ZIF 200 RF Input Return Loss Single Ended RFRL 14 20 dB LO port Return Loss Single Ended LORL 18 22 dB IF Output Return Loss Differential IFRL 17 19 dB LO to IF leakage2 RF to IF leakage Referenced to Pin = -10dBm LO to RF leakage Ω ISOLI -55 -39 dBm ISORI -41 -34 dBc ISOLR -43.5 -38 dBm 1 – Items in min/max columns in bold italics are Guaranteed by Test 2 – All other Items in min/max columns are Guaranteed by Design Characterization IDT Zero-DistortionTM Mixer 5 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TYPICAL OPERATING CONDITIONS Unless otherwise noted, the following conditions apply to the Typ Ops Graphs: VCC = +5.0V STBY = GND TC= +25°C FRF = 950 MHz FIF = 200 MHz FLO = 1150 MHz PLO = 0 dBm Pin = -10dBm per tone Transformer loss is de-embedded for Gain, Output P1dB and OIP3 Graphs IDT Zero-DistortionTM Mixer 6 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS [IF = 200MHZ, HIGH SIDE INJECTION] Gain, OIP3 (1) Gain vs. Lo Level 14 14 13 13 12 12 11 11 Gain (dB) Gain (dB) Gain vs. TCASE 10 9 8 7 10 9 8 7 105degC - +5.0V - 0dBm 6 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm 25degC - +5.0V - 0dBm 6 5 4 650 700 750 800 850 900 950 1000 1050 1100 650 700 RF Frequency (MHz) 800 850 900 950 1000 1050 1100 Output IP3 vs. TCASE 50 13 45 12 40 11 35 OIP3 (dBm) 14 10 9 8 7 25degC - +4.75V - 0dBm 6 750 RF Frequency (MHz) Gain vs. Vcc Gain (dB) 25degC - +5.0V - -3dBm 5 4 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm 30 25 20 15 105degC - +5.0V - 0dBm 10 5 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm 5 4 0 650 700 750 800 850 900 950 1000 1050 1100 650 700 RF Frequency (MHz) 45 40 40 35 35 OIP3 (dBm) 50 45 30 25 20 15 25degC - +5.0V - 0dBm 800 850 900 950 1000 1050 1100 Output IP3 vs. Vcc 50 10 750 RF Frequency (MHz) Output IP3 vs. Lo Level OIP3 (dBm) 25degC - +5.0V - 3dBm 25degC - +5.0V - 3dBm 25degC - +5.0V - -3dBm 30 25 20 15 25degC - +4.75V - 0dBm 10 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm 5 5 0 0 650 700 750 800 850 900 950 1000 1050 1100 700 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) RF Frequency (MHz) IDT Zero-DistortionTM Mixer 650 7 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS [IF = 200MHZ, HIGH SIDE INJECTION] P1dBo, 2X2 (2) P1dBO vs. Lo Level 30 30 28 28 26 26 P1dB Output (dBm) P1dB Output (dBm) P1dBO vs. TCASE 24 22 20 18 16 105degC - +5.0V - 0dBm 14 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm 12 24 22 20 18 16 25degC - +5.0V - 0dBm 14 10 650 700 750 800 850 900 950 1000 1050 1100 650 700 RF Frequency (MHz) -55 26 -60 2x2 Rejection (dBc) -50 28 24 22 20 18 16 25degC - +4.75V - 0dBm 900 950 1000 1050 1100 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm 850 900 950 1000 1050 -40degC - +5.0V - 0dBm -80 -85 -90 -95 800 25degC - +5.0V - 0dBm -75 -100 750 105degC - +5.0V - 0dBm -70 10 700 850 -65 12 650 800 2x2 Rejection vs. TCASE 30 14 750 RF Frequency (MHz) P1dBO vs. Vcc P1dB Output (dBm) 25degC - +5.0V - -3dBm 12 10 1100 650 700 RF Frequency (MHz) 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) 2x2 Rejection vs. Lo Level 2x2 Rejection vs. Vcc -50 -50 -55 -55 25degC - +5.0V - 0dBm -60 25degC - +5.0V - 3dBm 25degC - +5.0V - -3dBm 2x2 Rejection (dBc) 2x2 Rejection (dBc) 25degC - +5.0V - 3dBm -65 -70 -75 -80 -85 -90 -75 -80 -85 -90 -95 -100 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) IDT Zero-DistortionTM Mixer 25degC - +5.25V - 0dBm -70 -100 700 25degC - +5.0V - 0dBm -65 -95 650 25degC - +4.75V - 0dBm -60 650 700 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) 8 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS [IF = 200MHZ, HIGH SIDE INJECTION] 3x3, H2 Rejection (3) 3x3 Rejection vs. TCASE 3x3 Rejection vs. Lo Level -50 -50 -55 105degC - +5.0V - 0dBm -60 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm 3x3 Rejection (dBc) 3x3 Rejection (dBc) -55 -65 -70 -75 -80 -85 -90 -75 -80 -85 -90 -95 -100 750 800 850 900 950 1000 1050 1100 650 700 RF Frequency (MHz) -10 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm H2 Rejection (dBc) 3x3 Rejection (dBc) 0 -55 -65 -70 -75 -80 -85 -90 850 900 950 1000 1050 650 25degC - +5.0V - 3dBm 25degC - +5.0V - -3dBm H2 Rejection (dBc) H2 Rejection (dBc) 0 -30 -40 -50 -60 -70 -80 700 850 900 950 1000 1050 1100 950 1000 1050 1100 RF Frequency (MHz) 25degC - +5.25V - 0dBm -50 -60 -70 -80 -90 900 25degC - +5.0V - 0dBm -40 -100 IDT Zero-DistortionTM Mixer 800 -30 -100 850 750 25degC - +4.75V - 0dBm -20 -90 800 -40degC - +5.0V - 0dBm H2 Rejection vs. Vcc -10 750 25degC - +5.0V - 0dBm RF Frequency (MHz) 0 700 1100 -80 -10 650 1050 -70 1100 H2 Rejection vs. Lo Level 25degC - +5.0V - 0dBm 1000 -60 RF Frequency (MHz) -20 950 -50 -90 800 900 -40 -100 750 850 -30 -100 700 105degC - +5.0V - 0dBm -20 -95 650 800 H2 Rejection vs. TCASE -50 25degC - +4.75V - 0dBm 750 RF Frequency (MHz) 3x3 Rejection vs. Vcc -60 25degC - +5.0V - -3dBm -70 -100 700 25degC - +5.0V - 3dBm -65 -95 650 25degC - +5.0V - 0dBm -60 650 700 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) 9 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS [IF = 200MHZ, HIGH SIDE INJECTION] Icc, LO-IF leakage [4] Icc vs. TCASE Icc vs. Lo Level 0.25 0.25 0.24 0.24 0.23 105degC - +5.0V - 0dBm 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm 0.23 25degC - +5.0V - 0dBm 0.21 0.2 0.2 0.19 0.18 0.18 0.17 0.17 0.16 0.16 650 700 750 800 850 900 950 1000 1050 0.15 1100 650 700 750 RF Frequency (MHz) 850 900 950 1000 1050 1100 Lo to IF leakage vs. TCASE 0 0.24 -10 25degC - +4.75V - 0dBm 25degC - +5.0V - 0dBm Lo to IF leakage (dBm) 0.25 0.23 800 RF Frequency (MHz) Icc vs. Vcc 25degC - +5.25V - 0dBm 0.22 Icc (A) 25degC - +5.0V - -3dBm 0.21 0.19 0.15 0.21 0.2 0.19 0.18 0.17 0.16 105degC - +5.0V - 0dBm -20 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm -30 -40 -50 -60 -70 -80 -90 0.15 650 700 750 800 850 900 950 1000 1050 -100 1100 650 700 RF Frequency (MHz) 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) Lo to IF leakage vs. Lo Level Lo to IF leakage vs. Vcc 0 0 -10 25degC - +5.0V - 0dBm 25degC - +5.0V - 3dBm 25degC - +5.0V - -3dBm -10 Lo to IF leakage (dBm) Lo to IF leakage (dBm) 25degC - +5.0V - 3dBm 0.22 Icc (A) Icc (A) 0.22 -20 -30 -40 -50 -60 -70 -80 -90 25degC - +4.75V - 0dBm 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm -20 -30 -40 -50 -60 -70 -80 -90 -100 650 700 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) IDT Zero-DistortionTM Mixer -100 650 700 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) 10 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS [IF = 200MHZ, HIGH SIDE INJECTION] RF to IF leakage, OIP3, HD2 (5) RF to IF leakage vs. TCASE 0 -6 -6 105degC - +5.0V - 0dBm 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm RF to IF leakage (dBc) -12 RF to IF leakage (dBc) RF to IF leakage vs. Lo Level 0 -18 -24 -30 -36 -42 -48 -54 -60 650 750 850 950 25degC - +5.0V - 0dBm -12 -24 -30 -36 -42 -48 -54 -60 1050 650 750 850 950 1050 RF Frequency (MHz) RF to IF leakage vs. Vcc OIP3 vs. Input power 0 50 -6 45 25degC - +4.75V - 0dBm -12 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm 40 -18 35 -24 30 OIP3 (dBm) RF to IF leakage (dBc) 25degC - +5.0V - -3dBm -18 RF Frequency (MHz) -30 -36 -42 25 20 15 -48 10 -54 5 -60 650 750 850 950 25degC - +5.0V - 0dBm - 650MHz 25degC - +5.0V - 0dBm - 800MHz 25degC - +5.0V - 0dBm - 950MHz 25degC - +5.0V - 0dBm - 1100MHz 0 1050 -20 -18 -16 -14 -12 RF Frequency (MHz) -10 -8 -6 -4 -2 0 2 4 6 8 10 Input Power (dBm) HD2 vs. Input power OIP3 vs. Delta Frequency of two tones 0 50 -10 45 -20 -30 25degC - +5.0V - 0dBm - 650MHz 25degC - +5.0V - 0dBm - 800MHz 25degC - +5.0V - 0dBm - 950MHz 25degC - +5.0V - 0dBm - 1100MHz 40 35 OIP3 (dBm) -40 HD2 (dBc) 25degC - +5.0V - 3dBm -50 -60 -70 30 25 20 15 -80 10 -90 5 -100 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 8 10 Input Power (dBm) IDT Zero-DistortionTM Mixer 25degC - +5.0V - 0dBm - 650MHz 25degC - +5.0V - 0dBm - 800MHz 25degC - +5.0V - 0dBm - 950MHz 25degC - +5.0V - 0dBm - 1100MHz 0 0.8 2.8 4.8 6.8 8.8 10.8 12.8 14.8 16.8 18.8 20.8 22.8 24.8 26.8 28.8 30.8 Two tones Delta Frequency (MHz) 11 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS [IF = 200MHZ, LOW SIDE INJECTION] Gain, OIP3 (6) Gain vs. Lo Level 14 14 13 13 12 12 11 11 Gain (dB) Gain (dB) Gain vs. TCASE 10 9 8 7 10 9 8 7 105degC - +5.0V - 0dBm 6 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm 25degC - +5.0V - 0dBm 6 5 4 650 700 750 800 850 900 950 1000 1050 1100 650 700 RF Frequency (MHz) 800 850 900 950 1000 1050 1100 Output IP3 vs. TCASE 50 13 45 12 40 11 35 OIP3 (dBm) 14 10 9 8 7 25degC - +4.75V - 0dBm 6 750 RF Frequency (MHz) Gain vs. Vcc Gain (dB) 25degC - +5.0V - -3dBm 5 4 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm 30 25 20 15 105degC - +5.0V - 0dBm 10 5 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm 5 4 0 650 700 750 800 850 900 950 1000 1050 1100 650 700 RF Frequency (MHz) 45 40 40 35 35 OIP3 (dBm) 50 45 30 25 20 15 25degC - +5.0V - 0dBm 800 850 900 950 1000 1050 1100 Output IP3 vs. Vcc 50 10 750 RF Frequency (MHz) Output IP3 vs. Lo Level OIP3 (dBm) 25degC - +5.0V - 3dBm 25degC - +5.0V - 3dBm 25degC - +5.0V - -3dBm 30 25 20 15 25degC - +4.75V - 0dBm 10 5 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm 5 0 0 650 700 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) IDT Zero-DistortionTM Mixer 650 700 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) 12 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS [IF = 200MHZ, LOW SIDE INJECTION] P1dBo, 2x2 (7) P1dBO vs. Lo Level 30 30 28 28 26 26 P1dB Output (dBm) P1dB Output (dBm) P1dBO vs. TCASE 24 22 20 18 16 105degC - +5.0V - 0dBm 14 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm 12 24 22 20 18 16 25degC - +5.0V - 0dBm 14 10 650 700 750 800 850 900 950 1000 1050 1100 650 700 RF Frequency (MHz) -55 26 -60 2x2 Rejection (dBc) -50 28 24 22 20 18 16 25degC - +4.75V - 0dBm 900 950 1000 1050 1100 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm 850 900 950 1000 1050 -40degC - +5.0V - 0dBm -80 -85 -90 -95 800 25degC - +5.0V - 0dBm -75 -100 750 105degC - +5.0V - 0dBm -70 10 700 850 -65 12 650 800 2x2 Rejection vs. TCASE 30 14 750 RF Frequency (MHz) P1dBO vs. Vcc P1dB Output (dBm) 25degC - +5.0V - -3dBm 12 10 1100 650 700 RF Frequency (MHz) 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) 2x2 Rejection vs. Lo Level 2x2 Rejection vs. Vcc -50 -50 -55 -55 25degC - +5.0V - 0dBm -60 25degC - +5.0V - 3dBm 25degC - +5.0V - -3dBm 2x2 Rejection (dBc) 2x2 Rejection (dBc) 25degC - +5.0V - 3dBm -65 -70 -75 -80 -85 -90 -75 -80 -85 -90 -95 -100 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) IDT Zero-DistortionTM Mixer 25degC - +5.25V - 0dBm -70 -100 700 25degC - +5.0V - 0dBm -65 -95 650 25degC - +4.75V - 0dBm -60 650 700 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) 13 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS [IF = 200MHZ, LOW SIDE INJECTION] 3x3, H2 Rejection (8) 3x3 Rejection vs. TCASE 3x3 Rejection vs. Lo Level -50 -50 -55 105degC - +5.0V - 0dBm -60 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm 3x3 Rejection (dBc) 3x3 Rejection (dBc) -55 -65 -70 -75 -80 -85 -90 -75 -80 -85 -90 -95 -100 750 800 850 900 950 1000 1050 1100 650 700 RF Frequency (MHz) 0 -55 -10 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm 900 950 1000 1050 1100 105degC - +5.0V - 0dBm 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm -30 -70 -75 -80 -85 -90 -95 -100 -40 -50 -60 -70 -80 -90 -100 650 700 750 800 850 900 950 1000 1050 1100 650 700 750 800 H2 Rejection vs. Lo Level 0 0 -10 25degC - +5.0V - 0dBm 900 950 1000 1050 1100 H2 Rejection vs. Vcc -10 -20 850 RF Frequency (MHz) RF Frequency (MHz) 25degC - +5.0V - 3dBm -20 25degC - +5.0V - -3dBm 25degC - +4.75V - 0dBm 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm -30 H2 Rejection(dBc) -30 H2 Rejection(dBc) 850 -20 -65 H2 Rejection(dBc) 3x3 Rejection (dBc) 800 H2 Rejection vs. TCASE -50 25degC - +4.75V - 0dBm 750 RF Frequency (MHz) 3x3 Rejection vs. Vcc -60 25degC - +5.0V - -3dBm -70 -100 700 25degC - +5.0V - 3dBm -65 -95 650 25degC - +5.0V - 0dBm -60 -40 -50 -60 -70 -80 -90 -100 -40 -50 -60 -70 -80 -90 -100 650 700 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) IDT Zero-DistortionTM Mixer 650 700 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) 14 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS [IF = 200MHZ, LOW SIDE INJECTION] Icc, Lo to IF Leakage (9) Icc vs. TCASE Icc vs. Lo Level 0.25 0.25 0.24 0.24 0.23 105degC - +5.0V - 0dBm 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm 0.23 25degC - +5.0V - 0dBm 25degC - +5.0V - 3dBm 25degC - +5.0V - -3dBm 0.22 0.21 Icc (A) Icc (A) 0.22 0.2 0.19 0.21 0.2 0.19 0.18 0.18 0.17 0.17 0.16 0.16 0.15 650 700 750 800 850 900 950 1000 1050 0.15 1100 650 700 750 RF Frequency (MHz) 800 850 900 950 1000 1050 1100 RF Frequency (MHz) Icc vs. Vcc Lo to IF leakage vs. TCASE 0.25 0 0.24 0.23 25degC - +4.75V - 0dBm 25degC - +5.0V - 0dBm Lo to IF leakage (dBm) -4 25degC - +5.25V - 0dBm Icc (A) 0.22 0.21 0.2 0.19 0.18 0.17 0.16 105degC - +5.0V - 0dBm -8 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm -12 -16 -20 -24 -28 -32 -36 0.15 650 700 750 800 850 900 950 1000 1050 -40 1100 650 700 RF Frequency (MHz) 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) Lo to IF leakage vs. Lo Level Lo to IF leakage vs. Vcc 0 0 25degC - +5.0V - 0dBm -8 25degC - +5.0V - 3dBm -4 25degC - +5.0V - -3dBm Lo to IF leakage (dBm) Lo to IF leakage (dBm) -4 -12 -16 -20 -24 -28 -32 -36 25degC - +4.75V - 0dBm 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm -8 -12 -16 -20 -24 -28 -32 -36 -40 650 700 750 800 850 900 950 1000 1050 1100 -40 650 RF Frequency (MHz) IDT Zero-DistortionTM Mixer 700 750 800 850 900 950 1000 1050 1100 RF Frequency (MHz) 15 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS [IF = 200MHZ, LOW SIDE INJECTION] RF to IF leakage, OIP3, H2 (10) RF to IF leakage vs. TCASE 0 -6 -6 105degC - +5.0V - 0dBm 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm RF to IF leakage (dBc) -12 RF to IF leakage (dBc) RF to IF leakage vs. Lo Level 0 -18 -24 -30 -36 -42 -48 -54 -60 650 750 850 950 25degC - +5.0V - 0dBm -12 -24 -30 -36 -42 -48 -54 -60 1050 650 750 850 950 1050 RF Frequency (MHz) RF to IF leakage vs. Vcc OIP3 vs. Input power 0 50 -6 45 25degC - +4.75V - 0dBm -12 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm 40 -18 35 -24 30 OIP3 (dBm) RF to IF leakage (dBc) 25degC - +5.0V - -3dBm -18 RF Frequency (MHz) -30 -36 -42 25 20 15 -48 10 -54 5 -60 650 750 850 950 25degC - +5.0V - 0dBm - 650MHz 25degC - +5.0V - 0dBm - 800MHz 25degC - +5.0V - 0dBm - 950MHz 25degC - +5.0V - 0dBm - 1100MHz 0 1050 -20 -18 -16 -14 -12 RF Frequency (MHz) -10 -8 -6 -4 -2 0 2 4 6 8 10 Input Power (dBm) HD2 vs. Input power OIP3 vs. Delta Frequency of two tones 0 50 -10 45 -20 -30 25degC - +5.0V - 0dBm - 650MHz 25degC - +5.0V - 0dBm - 800MHz 25degC - +5.0V - 0dBm - 950MHz 25degC - +5.0V - 0dBm - 1100MHz 40 35 OIP3 (dBm) -40 HD2 (dBc) 25degC - +5.0V - 3dBm -50 -60 -70 30 25 20 15 -80 10 -90 5 -100 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 8 10 Input Power (dBm) IDT Zero-DistortionTM Mixer 25degC - +5.0V - 0dBm - 650MHz 25degC - +5.0V - 0dBm - 800MHz 25degC - +5.0V - 0dBm - 950MHz 25degC - +5.0V - 0dBm - 1100MHz 0 0.8 2.8 4.8 6.8 8.8 10.8 12.8 14.8 16.8 18.8 20.8 22.8 24.8 26.8 28.8 30.8 Two tones Delta Frequency (MHz) 16 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS NF, Settling Time, Return Loss (11) Noise Figure vs. TCASE Noise Figure with Blocker (RF: 950MHz, Blocker: 850MHz) 16 30 14 27 24 Noise Figure (dB) Noise Figure (dB) 12 10 8 6 4 105degC 25degC -40degC 2 21 18 15 12 9 6 3 0 0 600 700 800 900 1000 1100 1200 -30 -28 -26 -24 -22 -20 -18 -16 -14 -12 -10 1300 RF Frequency (MHz) -8 -6 -4 -2 0 2 4 6 Blocker Power (dBm) Turn on Settling Turn off Settling 0.4 0.4 0.3 Amplitude (Volts) Amplitude (Vlots) 0.3 0.2 0.1 0.0 -0.1 Signal -0.2 STBY 0.2 0.1 0.0 -0.1 -0.2 Signal -0.3 STBY -0.3 -0.4 -40 -20 0 20 40 60 80 -0.4 100 120 140 160 180 200 -40 Time (ns) -20 0 20 40 60 80 100 120 140 160 180 200 Time (ns) Lo port Return Loss RF port Return Loss -3 0 -6 -3 -9 -6 Return Loss (dB) Return Loss (dB) 0 -12 -15 -18 -21 -24 -9 -12 -15 -18 -21 -24 -27 -27 -30 500 593 686 780 873 967 1060 1154 1247 1341 1434 -30 Frequency (MHz) 500 621 743 864 985 1107 1228 1350 1471 Frequency (MHz) IDT Zero-DistortionTM Mixer 17 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz TOCS Return Loss (12) IF port Return Loss 0 -3 Return Loss (dB) -6 -9 -12 -15 -18 -21 -24 -27 -30 30 122 216 309 402 496 589 683 Frequency (MHz) IDT Zero-DistortionTM Mixer 18 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz PACKAGE DRAWING (NBG20) IDT Zero-DistortionTM Mixer 19 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz PIN DIAGRAM BLACK TEXT is recommended external connection RED TEXT denotes internal function or connection TOP View (looking through the top of the package) IF_SET IFOUT+ IFOUT- STBY L_EXT 20 19 18 17 16 C O 0. 35 m m Exposed Pad VCC 1 Package Drawing 15 NC RF_IN 2 5 mm x 5 mm package dimension 14 VCC 13 GND [LO_ADJ] 12 GND 11 LO_IN 3.1 mm x 3.1 mm exposed paddle GND [RF RTN] 3 0.65 mm pitch 20 pins GND 4 0.75 mm height 0.30 mm pad width IDT Zero-DistortionTM Mixer 20 8 9 10 GND 7 NC [die ID] 6 VCC 0.55 mm pad length IF_BIAS 5 VCC [NC] GND [NC] RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz PIN DESCRIPTIONS Pin Name Function 1 VCC Power Supply. Bypass to GND with capacitors shown in the Typical Application Circuit as close as possible to pin. 2 RF_IN RF Input. Internally matched to 50Ω. Do not apply DC to this pin. 3 GND [RF_RTN] RF input Balun return. Ground this pin 4 GND Internally bonded to GND 5 GND [NC] No Connection. Not internally connected. OK to connect to VCC. OK to connect to GND. 6 VCC [NC] No Connection. Not internally connected. OK to connect to VCC. OK to connect to GND. 7 IF_BIAS Connect the specified resistor from this pin to ground to optimize linearity. 8 VCC Power Supply. Bypass to GND with capacitors shown in the Typical Application Circuit as close as possible to pin. 9 NC [die ID] This pin serves as the die ID. Leave it unconnected 10 GND Internally bonded to GND 11 LO_IN Local Oscillator Input. This input is internally matched to 50Ω. This pin requires an input DC-blocking capacitor 12 GND 13 GND [LO_ADJ] 14 VCC 15 NC No Connection. Not internally connected. OK to connect to VCC. OK to connect to GND. 16 L_EXT Connect an external inductor to GND to optimize LO-IF leakage performance. 17 STBY Ground for normal operation. Pull high to disable 18 IF_OUT- Mixer Differential IF Output. Connect pullup inductor from this pin to VCC (see the Typical Application Circuit). 19 IF_OUT+ Mixer Differential IF Output. Connect pullup inductor from this pin to VCC (see the Typical Application Circuit). 20 IF_SET Connect the specified resistor from this pin to ground to set the correct Icc for the IF amplifier. — EP IDT Zero-DistortionTM Mixer Internally bonded to GND Ground this pin for best linearity performance. A resistor from this pin to GND can be used to reduce DC power consumption while slightly degrading linearity performance. Power Supply. Bypass to GND with capacitors shown in the Typical Application Circuit as close as possible to pin. Exposed Pad. Internally connected to GND. Connect to Ground with multiple vias for good thermal relief 21 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz EVKIT / APPLICATION CIRCUIT IDT Zero-DistortionTM Mixer 22 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz POWER SUPPLIES All supply pins should be bypassed with external capacitors to minimize noise and fast transients. Supply noise can degrade noise figure and fast transients can trigger ESD clamps and cause them to fail. Supply voltage change or transients should have a slew rate smaller than 1V/20uS. In addition, all control pins should remain at 0V (+/-0.3V) while the supply voltage ramps or while it returns to zero. EVKIT PICTURE/LAYOUT/OPERATION Output 4:1 Transformer Unused 50 ohm IF out Port DC Power Close for Normal Operation IDT Zero-DistortionTM Mixer 23 RevO December 2013 IDTF1701NBGI Datasheet RF to IF Single Downconverting Mixer 600MHz to 1060MHz EVKIT BOM F1701 11/26/2013 Item # Value 1 10nF 2 10uF 3 0.5pF 4 3pF 5 39pF Size/Rev 0402 0603 0402 0402 0402 Desc CAP CER 10000PF 16V 10% X7R 0402 CAP CER 10UF 6.3V X5R 0603 CAP CER 0.5PF 50V NP0 0402 CAP CER 3PF 50V C0G 0402 CAP CER 39PF 50V 5% C0G 0402 Mfr. Part # GRM155R71C103KA01D GRM188R60J106ME47D GJM1555C1HR50BB01D GRM1555C1H3R0CZ01D GRM1555C1H390JZ010 Mfr. MURATA MURATA MURATA MURATA MURATA Supplier Part # 490-1313-1-ND 490-3896-1-ND 490-6077-1-ND 490-3205-1-ND 490-1286-1-ND Supplier Digikey Digikey Digikey Digikey Digikey 6 0 0402 RES 0.0 OHM 1/10W 0402 SMD ERJ-2GE0R00X Panasonic P0.0JCT-ND Digikey 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 100 806 6.19K 47K 36nH 820nH 10nH Header_2Pin SMA_END_LAUNCH SMA_END_LAUNCH 4:1 Balun F1701 PCB BOM DNP 0402 0402 0402 0402 0402 0805 402 TH_2 .062 .062 SM-22 QFN-24 03 01 402 RES 100 OHM 1/10W 1% 0402 SMD RES 806 OHM 1/10W 1% 0402 SMD RES 6.19K OHM 1/10W 1% 0402 SMD RES 47.0K OHM 1/16W 1% 0402 SMD 0402 Inductor 36nH LQW series 0805CS (2012) Ceramic Chip Inductor 0402CS Ceramic Chip Inductor CONN HEADER VERT SGL 2POS GOLD CONN SMA JACK END LAUNCH PCB (Big) CONN SMA JACK END LAUNCH PCB (Small) 4:1 Center Tap Balun 50 OHM 3 TO 800Mhz IF MIXER NBG24 Printed Circuit Board Bill Of Material ERJ-2RKF1000X ERJ-2RKF8060X ERJ-2RKF6191X RC0402FR-0747KL LQW15AN36NJ00D 0805CS-821XJLB 0402CS-10NXJLU 961102-6404-AR 142-0701-851 142-0711-821 TC4-6TG2+ F1701 F1751 EV Kit Rev 03 Panasonic Panasonic Panasonic Yageo MURATA COILCRAFT COILCRAFT 3M Emerson Johnson Emerson Johnson Mini Circuits IDT P100LCT-ND P806LCT-ND P6.19KLCT-ND 311-47.0KLRCT-ND LQW15AN36NJ00D-ND 0805CS-821XJLB 0402CS-10NXJLU 3M9447-ND 530-142-0701-851 530-142-0711-821 TC4-6TG2+ F1701-014 Digikey Digikey Digikey Digikey Digikey COILCRAFT COILCRAFT Digikey Mouser Mouser Mini Circuits Part Reference C2,3,7,9,12 C4 C13 C14,15 C8,10 R2,3,4,5,6,7,10, 11,14,C1,C5 R15 R9 R13 R8 L1,4 L2,3 L5 JP1,2,3 J5,6 J2,3 T1 U1 R1,12,C6,11,JP3 Total Qty 5 1 1 2 2 11 1 1 1 1 2 2 1 3 2 2 1 1 1 41 TOP MARKINGS Part Number IDTF17 01NBGI ZB1321A Q96C014MY Die Step Date Code [YYWW] (Week 21 of 2013) Lot Code IDT Zero-DistortionTM Mixer 24 RevO December 2013