FEATURES ►Small Footprint: 24.0 x 18.1 mm (0.94 x 0.71 inches) ►Wide 2:1 Input Range ► Fully regulated Output ►Operating Temp. Range –40°C to +85°C ►Short Circuit Protection ►I/O-isolation 1500 VDC ►Input Filter meets EN55022,class A and FCC, level A ►Qualified for lead-free reflow solder process according IPC/JEDEC J-STD-020D ►3 Years Product Warranty PRODUCT OVERVIEW The MSDW1 series is a range of isolated 2W DC/DC converter modules featuring fully regulated output voltages and wide 2:1 input voltage ranges. The products come in a compact SMD package with a small footprint and low package height of just 8.0 mm (0.31 inch). All models are qualified for lead free reflow solder processes according IPC J-STD-020D standard. An excellent efficiency allows an operating temperature range of–40°C to +85°C. The compact dimensions of these DC/DC converters make them an ideal solution for many space critical applications in battery-powered equipment and instrumentation. Model Selection Guide Model Input Output Number Voltage Voltage (Range) VDC MSDW1011 MSDW1012 MSDW1013 MSDW1014 MSDW1015 MSDW1016 MSDW1017 MSDW1021 MSDW1022 MSDW1023 MSDW1024 MSDW1025 MSDW1026 MSDW1027 MSDW1031 MSDW1032 MSDW1033 MSDW1034 MSDW1035 MSDW1036 MSDW1037 MSDW1041 MSDW1042 MSDW1043 MSDW1044 MSDW1045 MSDW1046 MSDW1047 5 (4.5 ~ 9) 12 (9 ~ 18) 24 (18 ~ 36) 48 (36 ~ 75) VDC 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 Output Current Input Current Reflected Max. capacitive Ripple Load Max. Min. @Max. Load @No Load Current mA 500 400 167 134 ±200 ±83 ±67 500 400 167 134 ±200 ±83 ±67 500 400 167 134 ±200 ±83 ±67 500 400 167 134 ±200 ±83 ±67 mA 125 100 42 33 ±50 ±21 ±17 125 100 42 33 ±50 ±21 ±17 125 100 42 33 ±50 ±21 ±17 125 100 42 33 ±50 ±21 ±17 mA(typ.) 471 548 534 582 667 615 598 184 217 209 220 242 224 226 96 109 109 108 119 112 110 49 57 53 55 62 57 57 mA(typ.) mA(typ.) 40 100 20 25 10 15 8 10 Toll Free: 877-646-0900 (typ.) @Max. Load uF 2200 1000 170 110 470# 100# 47# 2200 1000 170 110 470# 100# 47# 2200 1000 170 110 470# 100# 47# 2200 1000 170 110 470# 100# 47# # For each output In Total Power International, Inc Efficiency www.total-power.com % 70 73 75 73 64 69 71 73 77 80 80 73 78 78 72 77 80 81 74 78 80 71 73 79 79 71 77 77 MSDW1000 SERIES Tota Total Power International, Inc. DC/DC CONVERTER 2W, SMD-Package Input Specifications Parameter Input Surge Voltage (1 sec. max.) Start-Up Voltage Under Voltage Shutdown Model Min. Typ. Max. 5V Input Models -0.7 --- 11 12V Input Models -0.7 --- 25 24V Input Models -0.7 --- 50 48V Input Models -0.7 --- 100 4.5 5V Input Models 3.5 4 12V Input Models 4.5 7 9 24V Input Models 8 12 18 48V Input Models 16 24 36 5V Input Models --- 3.5 4 12V Input Models --- 6.5 8.5 24V Input Models --- 11 17 48V Input Models --- 22 34 --- --- 1 Reverse Polarity Input Current Short Circuit Input Power Internal Power Dissipation All Models Conducted EMI Unit VDC A --- --- 1500 mW --- --- 1800 mW Compliance to EN 55022,class A and FCC part 15,class A Output Specifications Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20MHz) Ripple & Noise (20MHz) Ripple & Noise (20MHz) Transient Recovery Time Transient Response Deviation Temperature Coefficient Short Circuit Protection Conditions Dual Output, Balanced Loads Vin=Min. to Max. Io=25% to 100% Over Line, Load & Temp. Min. --------------- Typ. ±1.0 ±1.0 ±0.3 ±0.5 30 ----- Max. ±2.0 ±2.0 ±0.5 ±0.75 50 75 15 Unit % % % % mV P-P mV P-P mV rms --- 100 300 uS ----- ±3 ±0.01 ±5 ±0.02 % %/℃ 25% Load Step Change Continuous General Specifications Parameter Conditions Min. Typ. Max. Unit 60 Seconds 1500 --- --- VDC I/O Isolation Resistance 500 VDC 1000 --- --- MΩ I/O Isolation Capacitance 100KHz, 1V --- 250 420 pF --- 300 --- KHz 1,000,000 --- --- Hours I/O Isolation Voltage (rated) Switching Frequency MTBF (calculated) Moisture Sensitivity Level (MSL) MIL-HDBK-217F@25℃, Ground Benign IPC/JEDEC J-STD-020D Level 2 Input Fuse 5V Input Models 1000mA Slow-Blow Type 12V Input Models 500mA Slow-Blow Type 24V Input Models 250mA Slow-Blow Type 48V Input Models 120mA Slow-Blow Type Environmental Specifications Parameter Operating Temperature Range (with Derating) Case Temperature Storage Temperature Range Humidity (non condensing) Cooling Lead Temperature (1.5mm from case for 10Sec.) In Total Power International, Inc Conditions Ambient Toll Free: 877-646-0900 Min. -40 ---50 --Free-Air convection --- Max. +85 +90 +125 95 Unit ℃ ℃ ℃ % rel. H 260 ℃ www.total-power.com MSDW1000 SERIES Total Power International, Inc. Tota DC/DC CONVERTER 2W, SMD-Package Power Derating Curve 100 Natural convection 80 100LFM 200LFM 60 400LFM 40 20 0 ~ -40 0 20 40 60 100 110 80 Ambient Temperature ] Notes 1 Specifications typical at Ta=+25℃, resistive load, nominal input voltage and rated output current unless otherwise noted. 2 Transient recovery time is measured to within 1% error band for a step change in output load of 75% to 100% 3 Ripple & Noise measurement bandwidth is 0-20MHz. 4 These power converters require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage these modules; 5 All DC/DC converters should be externally fused at the front end for protection. 6 Other input and output voltage may be available, please contact factory. 7 Specifications subject to change without notice. 8 It is not recommended to use water-washing process on SMT units. however they may not meet all specifications listed. Package Specifications Mechanical Dimensions Connecting Pin Patterns 24.0 [0.94] 17.78mm 15.24 [0.6] 2.54 [0.1] 1.4mm(Min) 2.8mm 10 9 13.7 [0.54] 16 18.1 [0.71] 3.11 [0.12] 19.3mm 13.7mm 7 8 1 1.00 [0.04] 8.0 [0.31] 15.24mm 2.54mm ►All 0~ 4 8.25 0.5 [0.32 0.02] 0.25 [0.01] S SEATING PLANE dimensions in mm (inches) ►Tolerance: X.X±0.25 0.15 S X.XX±0.13 ( X.XXX±0.005) ►Pins Pin Connections ±0.05 (±0.002) Physical Characteristics Pin Single Output Dual Output 1 -Vin -Vin 7 NC NC 8 NC Common 9 +Vout +Vout 10 -Vout -Vout +Vin +Vin 16 (X.XX±0.01) Case Size : 24.0x13.7x8.0mm (0.94x0.54x0.31 Inches) Case Material : Non-Conductive Black Plastic (flammability to UL 94V-0 rated) Weight : 5.1g NC : No Connection In Total Power International, Inc Toll Free: 877-646-0900 www.total-power.com MSDW1000 SERIES Total Power International, Inc. Tota DC/DC CONVERTER 2W, SMD-Package Test Configurations Input Reflected-Ripple Current Test Setup Input reflected-ripple current is measured with a inductor Lin (4.7uH) and Cin (220uF, ESR < 1.0Ω at 100 KHz) to simulate source impedance. Capacitor Cin, offsets possible battery impedance. Current ripple is measured at the input terminals of the module, measurement bandwidth is 0-500 KHz. To Oscilloscope + + Battery +Vin Lin DC / DC Converter Current Probe Cin +Out -Vin Load -Out Peak-to-Peak Output Noise Measurement Test Use a Cout 0.47uF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load between 50 mm and 75 mm from the DC/DC Converter. +Vin +Out Copper Strip Single Output DC / DC Converter -Vin Cout -Out Scope Resistive Load Copper Strip +Vin +Out Copper Strip Dual Output DC / DC Converter Com. Copper Strip -Vin -Out Scope Cout Cout Resistive Load Scope Copper Strip Design & Feature Considerations Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current limiting circuitry and can endure current limiting for an unlimited duration. At the point of current-limit inception, the unit shifts from voltage control to current control. The unit operates normally once the output current is brought back into its specified range. Input Source Impedance The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor on the input to insure startup. By using a good quality low Equivalent Series Resistance (ESR < 1.0Ω at 100 kHz) capacitor of a 8.2uF for the 5V input devices, a 3.3uF for the 12V input devices and a 1.5uF for the 24V and 48V devices, capacitor mounted close to the power module helps ensure stability of the unit. + DC Power Source +Vin + +Out DC / DC Converter Load Cin - -Vin -Out Output Ripple Reduction A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. To reduce output ripple, it is recommended to use 3.3uF capacitors at the output. + +Vin DC Power Source - +Out Single Output DC / DC Converter -Vin + Cout Load -Out +Vin DC Power Source - +Out Dual Output Com. DC / DC Converter -Vin -Out Cout Load Load Cout Maximum Capacitive Load The MSDW1000 series has limitation of maximum connected capacitance on the output. The power module may operate in current limiting mode during start-up, affecting the ramp-up and the startup time. The maximum capacitance can be found in the data sheet. Thermal Considerations Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 90℃. The derating curves are determined from measurements obtained in a test setup. Position of air velocity probe and thermocouple 50mm / 2in 15mm / 0.6in In Total Power International, Inc Air Flow DUT Toll Free: 877-646-0900 www.total-power.com