CAT5127, CAT5129 32-Tap Digitally Programmable Potentiometer (DPP™) FEATURES DESCRIPTION 32-position linear taper potentiometer The CAT5127/CAT5129 are single digitally program– mable potentiometers (DPP™) designed as a electro– nic replacement for mechanical potentiometers and trim pots. Ideal for automated adjustments on high volume production lines, they are also well suited for applications where equipment requiring periodic adjustment is either difficult to access or located in a hazardous or remote environment. Non-volatile EEPROM wiper storage Low standby current Single supply operation: 2.5V – 5.5V Increment Up/Down serial interface Resistance values: 10kΩ, 50kΩ and 100kΩ CAT5127 in tiny 8 lead 2mmx2.5mm TDFN and MSOP packages The CAT5127 contains a 32-tap series resistor array connected between two terminals RH and RL. The CAT5129 contains a 32-tap series resistor array connected between two terminals RH and GND. An up/down counter and decoder that are controlled by three input pins, determines which tap is connected to the wiper. The wiper setting, stored in nonvolatile me– mory, is not lost when the device is powered down and is automatically reinstated when power is returned. The wiper can be adjusted to test new system values without effecting the stored setting. Wiper-control of the CAT5127/CAT5129 is ¯¯ , U/D̄, accomplished with three input control pins, CS ¯¯¯ . The INC ¯¯¯ input increments the wiper in the and INC direction which is determined by the logic state of the ¯¯ input is used to select the device U/D̄ input. The CS and also store the wiper position prior to power down. CAT5129 in the 6 lead TSOT23 package APPLICATION Automated product calibration Remote control adjustments Offset, gain and zero control Tamper-proof calibrations Contrast, brightness and volume controls Motor controls and feedback systems Programmable analog functions For Ordering Information details, see page 11. The devices are used as two-terminal variable resistors. DPPs bring variability and programmability to a wide variety of applications including control, parameter adjustments, and signal processing. FUNCTIONAL DIAGRAM CAT5127 CAT5129 VCC VCC RH RH (U/D) (INC) (U/D) Control and Memory (INC) (CS) Control and Memory (CS) POR RL POR GND © 2006 Catalyst Semiconductor, Inc. Characteristics subject to change without notice GND 1 Doc. No. 2127 Rev. A CAT5127, CAT5129 PIN CONFIGURATION MSOP/TDFN CAT5127 ¯¯¯ INC 1 8 VCC U/D̄ 2 ¯¯ 7 CS RH 3 6 RL GND 4 5 NC PIN DESCRIPTIONS Name Function TSOT23-6 CAT5129 ¯¯¯ INC CAT5127 CAT5129 MSOP/TDFN SOT23 Increment Control 1 4 2 3 3 5 4 2 No Connect Potentiometer Low T i l Chip Select 5 - Supply Voltage Up/Down Control Potentiometer High RH T i l GND Ground U/D̄ NC RL ¯¯ CS 1 6 VCC ¯¯ CS GND 2 5 RH VCC U/D̄ 3 ¯¯¯ 4 INC 6 - 7 1 8 6 DEVICE DESCRIPTION ¯¯¯ : Increment Control Input INC ¯¯¯ input moves the wiper in the up or down The INC direction determined by the condition of the U/D̄ input. RL: Low End Potentiometer Terminal (CAT5127 only) RL is the low end terminal of the potentiometer. It is not required that this terminal be connected to a potential less than the RH terminal. Voltage applied to the RL terminal cannot exceed the supply voltage, VCC or go below ground, GND. RL and RH are electrically interchangeable. U/D̄: Up/Down Control Input The U/D̄ input controls the direction of the wiper ¯¯ is low, any movement. When in a high state and CS ¯¯¯ will cause the wiper to high-to-low transition on INC move one increment toward the RH terminal. When in ¯¯ is low, any high-to-low transition a low state and CS ¯¯¯ will cause the wiper to move one increment on INC towards the RL terminal. ¯¯ : Chip Select CS The chip select input is used to activate the control input of the device and is active low. When in a high ¯¯¯ and U/D̄ inputs will not affect state, activity on the INC or change the position of the wiper. RH: High End Potentiometer Terminal RH is the high end terminal of the potentiometer. It is not required that this terminal be connected to a potential greater than the RL terminal. Voltage applied to the RH terminal cannot exceed the supply voltage, VCC or go below ground, GND. Doc. No. 2127 Rev. A VCC: Supply Input for the device. 2 © 2006 Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5127, CAT5129 DEVICE OPERATION ¯¯ set LOW, the device is selected and will With CS ¯¯¯ inputs. HIGH to LOW respond to the U/D̄ and INC ¯¯¯ wil increment or decrement the transitions on INC wiper (depending on the state of the U/D̄ input and five-bit counter). The wiper, when at either end terminal, acts like its mechanical equivalent and does not move beyond the last position. The value of the ¯¯ counter is stored in nonvolatile memory whenever CS ¯¯¯ input is also HIGH. transitions HIGH while the INC When the device is powered-down, the last stored wiper counter position is maintained in the nonvolatile memory. When power is restored, the contents of the memory are recalled and the counter is set to the value stored. The CAT5127 operates like a digitally controlled variable resistor with RH and RL equivalent to the high and low terminals. There are 32 available tap positions including the resistor end points, RH and RL. There are 31 resistor elements connected in series between the RH and RL terminals. The CAT5129 operates like a digitally controlled variable resistor with RH equivalent to the high terminal. There are 32 available tap positions including the resistor end points, RH and GND. There are 31 resistor elements connected in series between the RH and GND terminals. ¯¯¯, U/D̄ and Operation is controlled by three inputs, INC ¯¯ . These inputs control a five-bit up/down counter CS whose output is decoded to select the wiper position. The selected wiper position can be stored in ¯¯¯ and CS ¯¯ inputs. nonvolatile memory using the INC ¯¯¯ set low, the device may be de-selected and With INC powered down without storing the current wiper position in nonvolatile memory. This allows the system to always power up to a preset value stored in nonvolatile memory. OPERATION MODES ¯¯¯ INC ¯¯ CS U/D̄ Operation High to Low Low High Wiper toward H High to Low Low Low Wiper toward L/GND High Low to High X Store Wiper Position Low Low to High X No Store, Return to Standby X High X Standby RH CH CL RL/GND Variable Resistor Equivalent Circuit © 2006 Catalyst Semiconductor, Inc. Characteristics subject to change without notice 3 Doc. No. 2127 Rev. A CAT5127, CAT5129 ABSOLUTE MAXIMUM RATINGS(1) Parameters Supply Voltage VCC to GND Inputs ¯¯ to GND CS ¯¯¯ to GND INC U/D̄ to GND H to GND L to GND W to GND Ratings Units -0.5 to +7V V -0.5 to VCC +0.5 -0.5 to VCC +0.5 -0.5 to VCC +0.5 -0.5 to VCC +0.5 -0.5 to VCC +0.5 -0.5 to VCC +0.5 V V V V V V Parameters Operating Ambient Temperature Commercial (‘C’ or Blank suffix) Industrial (‘I’ suffix) Junction Temperature Storage Temperature Lead Soldering (10 sec max) Ratings Units 0 to 70 -40 to +85 +150 -65 to 150 +300 ºC ºC ºC ºC ºC Max Units RELIABILITY CHARACTERISTICS Symbol Parameter Test Method Min VZAP(2) ILTH(2) (3) Typ ESD Susceptibility MIL-STD-883, Test Method 3015 2000 V Latch-Up JEDEC Standard 17 100 mA TDR Data Retention MIL-STD-883, Test Method 1008 100 Years NEND Endurance MIL-STD-883, Test Method 1003 1,000,000 Stores Notes: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. (2) (3) (4) This parameter is tested initially and after a design or process change that affects the parameter. Latch-up protection is provided for stresses up to 100mA on address and data pins from -1V to VCC + 1V These parameters are periodically sampled and are not 100% tested. Doc. No. 2127 Rev. A 4 © 2006 Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5127, CAT5129 DC ELECTRICAL CHARACTERISTICS VCC = +2.5V to +5.5V unless otherwise specified Power Supply Symbol Parameter VCC Operating Voltage Range ICC1 Supply Current (Increment) ICC2 Supply Current (Write) ISB1(1) Supply Current (Standby) Conditions Min Typ Max 2.5 Units 5.5 V VCC = 5.5V, f = 1MHz, IW = 0 0.4 10 µA Programming, VCC = 5.5V 300 1000 µA VCC = 3V ¯¯ = VCC CS ¯¯¯ = VCC or GND U/D̄, INC 150 500 µA 0.35 1 µA Logic Inputs Symbol Parameter Conditions IIH Input Leakage Current VIN = VCC 10 µA IIL Input Leakage Current VIN = 0V -10 µA 2 VCC V 0 0.8 V VCC x 0.7 VCC + 0.3 V -0.3 VCC x 0.2 V VIH1 TTL High Level Input Voltage VIL1 TTL Low Level Input Voltage VIH2 CMOS High Level Input Voltage VIL2 CMOS Low Level Input Voltage 4.5V ≤ VCC ≤ 5.5V 2.5V ≤ VCC ≤ 6V Min Typ Max Units POTENTIOMETER CHARACTERISTICS Symbol RPOT Parameter Potentiometer Resistance Conditions Min Typ -10 Device 10 -50 Device 50 -00 Device 100 Max Units kΩ RTOL Pot Resistance Tolerance VRH Voltage on RH pin VRL Voltage on RL pin RES Resolution INL Integral Linearity Error IW ≤ 2µA 0.5 1 LSB DNL Differential Linearity Error IW ≤ 2µA 0.25 0.5 LSB RWi Wiper Resistance VCC = 5V, IW = 1mA 70 400 Ω VCC = 2.5V, IW = 1mA 150 1000 Ω 1 mA IW (2) ± 20 % 0 VCC V 0 VCC V 3.2 Wiper Current % TCRPOT (3) TC of Pot Resistance ±30 ±300 ppm/ºC TCRATIO (3) Ratiometric TC ±3 20 ppm/ºC VN (3) CH/CL/CW Fc (3) Noise (3) 100kHz / 1kHz Potentiometer Capacitances Frequency Response Passive Attenuator, 10kΩ 8/24 nV/√Hz 8/8/25 pF 1.7 MHz Notes: (1) Latch-up protection is provided for stresses up to 100mA on address and data pins from -1V to VCC + 1V (2) IW = source or sink (3) These parameters are periodically sampled and are not 100% tested. © 2006 Catalyst Semiconductor, Inc. Characteristics subject to change without notice 5 Doc. No. 2127 Rev. A CAT5127, CAT5129 AC TEST CONDITIONS VCC Range 2.5V ≤ VCC ≤ 5.5V Input Pulse Levels 0.2VCC to 0.7VCC Input Rise and Fall Times 10ns Input Reference Levels 0.5VCC AC OPERATING CHARACTERISTICS VCC = +2.5V to +5.5V, VH = VCC, VL = 0V, unless otherwise specified Symbol tCI tDI tID tIL tIH tIC tCPH tCPH tIR tCYC (2) tR, tF tPU (2) tWR Parameter Min ¯¯ to INC ¯¯¯ Setup CS ¯¯¯ Setup U/D̄ to INC 100 ns 50 ns ¯¯¯ Hold U/D̄ to INC ¯¯¯ LOW Period INC 100 ns 250 ns ¯¯¯ HIGH Period INC ¯¯¯ Inactive to CS Inactive INC 250 ns 1 µs ¯¯ Deselect Time (NO STORE) CS ¯¯ Deselect Time (STORE) CS 100 ns 10 ms ¯¯¯ to RH Change INC ¯¯¯ Cycle Time INC Typ(1) Max 1 Units 5 µs 1 µs ¯¯¯ Input Rise and Fall Time INC Power-up to Wiper Stable Store Cycle 2 500 µs 1 ms 5 ms A.C. TIMING CS tCI tIL tCYC (store) tIC tIH tCPH 90% INC 90% 10% tDI tID tF U/D tR MI(3) tIR RH Notes: (1) (2) (3) Typical values are for TA=25ºC and nominal supply voltage. This parameter is periodically sampled and not 100% tested. MI in the A.C. Timing diagram refers to the minimum incremental change in the W output due to a change in the wiper position. Doc. No. 2127 Rev. A 6 © 2006 Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5127, CAT5129 APPLICATION INFORMATION Potentiometer Configurations (a) resistive divider (b) variable resistance (c) two-port Applications 3 V1 (-) 2 + A1 R3 1 R4 DPP +5V 8 2 R1 1 8 2 +5V 9 R2 R2 – + 10 +5V +5V – 4 RA R1 1 A3 } } 7 VO 8 4 11 7 RB CAT5127 CAT5127 V2 (+) 5 – R3 A2 4 (1-p)RPOT 8 7 3 555 R4 6 +2.5V 7 + pRPOT 3 R2 4 6 6 5 2 1 C 0.01µF 0.01µF 0.003µF Programmable Instrumentation Amplifier Programmable Sq. Wave Oscillator (555) +5V 100kΩ 8 2 CAT5127 1 7 V O (REG) R1 2952 VIN (UNREG) SHUTDOWN 1µF SD GND FB 11kΩ 1.23V 0.1µF 4 6.8µF 6 2 820 8 3 1 IS R3 7 4 CAT5127 10k 330 1M 3 – 7 +5V 3 + 4 2 6 A1 – + 3 7 6 VO 4 A2 LT1097 6 +2.5V Programmable Voltage Regulator © 2006 Catalyst Semiconductor, Inc. Characteristics subject to change without notice (1-p)R +5V R2 +5V 2 pR 330 } } VOUT Programmable I to V convertor 7 Doc. No. 2127 Rev. A CAT5127, CAT5129 PACKAGE OUTLINES 8-LEAD MSOP E1 e e E e D GAUGE PLANE A2 A c L2 θ b L A1 L1 SYMBOL MIN NOM MAX A1 0.05 0.10 0.15 A2 0.75 0.85 0.95 b 0.28 0.33 0.38 D 2.90 3.00 3.10 E 4.80 4.90 5.00 E1 2.90 3.00 3.10 A 1.1 c e L 0.65 BSC 0.35 0.45 0.55 L1 L2 Ө 0º 6º For current Tape and Reel information, download the PDF file from: http://www.catsemi.com/documents/tapeandreel.pdf. Notes: (1) (2) (3) All dimensions are in millimeters. Angles in degrees. Complies with JEDEC Specification MS-187. Stand off height/coplanarity are considered as special characteristics. Doc. No. 2127 Rev. A 8 © 2006 Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5127, CAT5129 8-LEAD TDFN (2.5 x 2.0mm) SYMBOL MIN NOM MAX A 0.70 0.75 0.80 A1 0.00 0.02 0.05 A3 0.20 REF b 0.20 0.25 0.30 D 1.90 2.00 2.10 D2 1.40 1.50 1.60 E 2.40 2.50 2.60 E2 1.20 1.30 1.40 e L 0.50 TYP 0.20 0.30 A1 0.40 A3 Notes: (1) (2) All dimensions are in millimeters. Angles in degrees. Complies with JEDEC specification MO-229. For current Tape and Reel information, download the PDF file from: http://www.catsemi.com/documents/tapeandreel.pdf. © 2006 Catalyst Semiconductor, Inc. Characteristics subject to change without notice 9 Doc. No. 2127 Rev. A CAT5127, CAT5129 6-LEAD TSOT-23 e e E E1 e1 D A2 GAUGE PLANE c A L2 L A1 b θ L1 SYMBOL A A1 A2 b c D E E1 e e1 L L1 L2 θ MIN — 0.01 0.80 0.30 0.12 2.70 0.30 0° NOM — 0.05 0.87 — 0.15 2.90 BSC 2.80 1.60 BSC 0.95 BSC 1.90 BSC 0.40 0.60 REF 0.25 BSC MAX 1.00 0.1 0.90 0.45 0.20 2.90 0.50 8° For current Tape and Reel information, download the PDF file from: http://www.catsemi.com/documents/tapeandreel.pdf. Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC specification MO-193. Doc. No. 2127 Rev. A 10 © 2006 Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5127, CAT5129 EXAMPLE OF ORDERING INFORMATION Prefix Device # CAT Suffix 5127 Z I -10 – G Temperature Range I = Industrial (-40ºC to 85ºC) Company ID Product Number 5127 5129 Tape & Reel T: Tape & Reel 3: 3000/Reel Resistance -10: 10k ohms -50: 50k ohms -00: 100k ohms Package Z: MSOP TD: TSOT23 ZD7: TDFN T3 Lead Finish Blank: Matte-Tin G: NiPdAu Notes: (1) (2) (3) (4) All packages are RoHS-compliant (Lead-free, Halogen-free). The standard lead finish is Matte-Tin. The device used in the above example is a CAT5127ZI-10-GT3 (MSOP, Industrial Temperature range, 10kΩ, NiPdAu, Tape & Reel). For additional package and temperature options, please contact your nearest Catalyst Semiconductor Sales office. ORDERING INFORMATION Device Ordering Part Number Resistor [kΩ] Top Marking Pin/Package Part Per Reel CAT5127 CAT5127ZI-10-T3 10 ABPU MSOP-8 3000 CAT5127ZI-50-T3 (5) 50 ABPV MSOP-8 3000 CAT5127ZI-00-T3 (5) 100 ABPY MSOP-8 3000 CAT5127ZI-10-GT3 10 ABNA MSOP-8 3000 CAT5127ZI-50-GT3 (5) 50 ABNB MSOP-8 3000 CAT5127ZI-00-GT3 (5) 100 ABNK MSOP-8 3000 CAT5127ZD7I-10-GT3 10 HB TDFN-8 3000 (5) 50 HC TDFN-8 3000 (5) 100 HD CAT5127ZD7I-50-GT3 CAT5127ZD7I-00-GT3 CAT5129 CAT5129TDI-10-T3 CAT5129TDI-50-T3 (5) CAT5129TDI-00-T3 (5) CAT5129TDI-10-GT3 CAT5129TDI-50-GT3 (5) CAT5129TDI-00-GT3 (5) 10 TDFN-8 3000 (6) TSOT23-6 3000 (6) TSOT23-6 3000 (6) TSOT23-6 3000 (6) TSOT23-6 3000 (6) TSOT23-6 3000 (6) TSOT23-6 3000 PDym 50 PEym 100 PFym 10 PAym 50 PBym 100 PCym Notes: (5) (6) Contact factory for availability. y = Production year (digit), m = Production month (digit). © 2006 Catalyst Semiconductor, Inc. Characteristics subject to change without notice 11 Doc. No. 2127 Rev. A REVISION HISTORY Date 12/18/06 Rev. A Reason Initial Issue Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: Beyond Memory™, DPP™, EZDim™, MiniPot™, and Quad-Mode™ Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal injury or death may occur. Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale. Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical semiconductor applications and may not be complete. Catalyst Semiconductor, Inc. Corporate Headquarters 2975 Stender Way Santa Clara, CA 95054 Phone: 408.542.1000 Fax: 408.542.1200 www.catsemi.com Document No: 2127 Revision: A Issue date: 12/18/06