Series 1-DCL • Optically Coupled MOSFET output • Ratings from 7A to 40A @ 200 VDC, and from 7A to 10A @ 500 VDC • DC Control • Relays are easily paralleled for higher-current applications PRODUCT SELECTION Load Voltage 100 VDC 200 VDC 400 VDC 500 VDC 7A 10A D1D07L D2D07L D4D07L D5D07L 12A 20A 40A D1D12L D2D12L D4D12L D1D20L D1D40L D2D40L D5D10L OUTPUT SPECIFICATIONS (1) Description Operating Voltage Range Maximum Off-State Leakage Current @ Rated Voltage [mA] Maximum Load Current (3) [Adc] Minimum Load Current [mA] Maximum Surge Current [Adc] (10ms) Maximum On-State Voltage Drop @ Rated Current [Vdc] Thermal Resistance Junction to Case (Rjc) [°C/W] Maximum On-State Resistance [RDS-ON][Ohms] 7A 12A 20A 40A 7A 12A 40A 7A 12A 7A 10A 0-100 0.1 7 1 15 2.0 2.2 0.29 0-100 0.2 12 1 28 1.6 1.34 0.13 0-100 0.3 20 1 42 2.1 1.06 0.10 0-100 0.3 40 1 106 2.1 0.83 0.05 0-200 0.1 7 1 22 2.0 1.5 0.29 0-200 0.3 12 1 27 2.8 1.06 0.23 0-200 0.3 40 1 106 2.1 0.83 0.05 0-400 0.3 7 1 17 4.2 1.06 0.6 0-400 0.3 12 1 36 4.2 0.8 0.35 0-500 0.2 7 1 19 5.7 1.0 0.8 0-500 0.3 10 1 29 5.5 0.8 0.55 INPUT SPECIFICATIONS (1) Description Control Voltage Range Minimum Turn-On Voltage Minimum Turn-Off Voltage Minimum Input Current @ 3.5V Maximum Input Current @ 32VDC Nominal Input Impedance Maximum Turn-On Time [msec] Maximum Turn-Off Time [msec] 3.5-32 VDC 3.5 VDC 1.0 VDC 8.4 mA 10.6 mA See Note 4 1.0 1.0 GENERAL SPECIFICATIONS Description Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 V DC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Encapsulation Terminals Recommended Terminal Screw Torque Range: Parameters 2500 VRMS 109 Ohm 50 pF -40 to 80°C -40 to 125 °C 3.0 oz (86.5g) Thermally conductive Epoxy Screws and Saddle Clamps Furnished, Unmounted 6-32 Screws - 10 in lbs. 8-32 and 10-32 Screws -20 in. lbs. (Screws dry without grase) GENERAL NOTES 1) All parameters at 25°C and per section unless otherwise specified. 2) Dielectric strength and insulation resistance are measured between input and output 3) Heat sinking required, for derating curves see page 3. 4) Input circuitry version incorporates active current limiter. MECHANICAL SPECIFICATIONS THERMAL DERATE INFORMATION WIRING DIAGRAM MAXIMUM SURGE VS DURATION AGENCY APPROVALS Designed in accordance with the requirements of IEC 62314 E116950 (100 and 200V models except D2D40L) Rev. 120811 ANNEX - ENVIROMENTAL INFORMATION