Release by PARA LIGHT DCC PARA LIGHT ELECTRONICS CO., LTD. 4F, No.1, Lane 93, Chien Yi Road, Chung Ho City, Taipei, Taiwan Tel: 886-2-2225-3733 Fax: 886-2-2225-4800 E-mail: [email protected] http://www.para.com.tw DATA SHEET PART NO.: L-T650SGCT REV: A / 2 CUSTOMER’S APPROVAL : _______________ DCC : ____________ DRAWING NO. : DS-7B-08-0003 DATE: 2009-10-31 PAGE 1 of 15 PARA-FOR-065 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED Part No. : L-T650SGCT REV: A / 2 Features Top view, Wide view angle, pure color PLCC 2 package SMD LED . EIA STD package, packing in 8mm tape on 7" diameter reels (ANSI/EIA-481-B-2001). Compatible with automatic Pick & Place equipment. Compatible with IR Reflow soldering and TTW soldering. Pb free product and acceptable lead-free process. Meet RoHS Green Product. Application Backlighting ( Switches, keys, displays, illuminated advertising) Emergency lighting / Signal and symbol luminaries. Package Outline Dimensions TOP VIEW SIDE VIEW 3.00 1.40 0.90 50° 2.00 0.15±0.03 C0.45 POLARITY - + FRONT VIEW BACK VIEW 2.70 3° 1.30 1.20 1.90 50° 0.75 Notes: 1. All dimensions are in millimeters. 2. Tolerance is ± 0.10mm (.004") unless otherwise noted. DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 2 of 15 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED REV: A / 2 Part No. : L-T650SGCT CHIP MATERIALS Dice Material :InGaN Light Color : Pure Green Lens Color : Water Clear Absolute Maximum Ratings(Ta=25℃ ℃) Symbol PD Parameter Power Dissipation Peak Forward Current IPF (1/10 Duty Cycle, 0.1ms Pulse Width) Rating Unit 85 mW 100 mA IF Continuous Forward Current 20 mA VR Reverse Voltage 5 V 1000 V ESD Electrostatic Discharge Threshold(HBM)Note A Topr Operating Temperature Range -40 ~ + 85 ℃ Tstg Storage Temperature Range -40 ~ + 85 ℃ Tsld Soldering Temperature (One times MAX.) Reflow Soldering:260℃ (for 10seconds) Hand Soldering:350℃ (for 3 seconds) Note A : HBM : Human Body Model. Seller gives no other assurances regarding the ability of to withstand ESD. Electro-Optical Characteristics (Ta=25℃ ℃) Parameter Luminous Intensity Symbol Min. Typ. IV 650 Max. Unit Test Condition 1000 mcd IF=20mA Viewing Angle 2θ1/2 120 Deg Peak Emission Wavelength λp 520 nm Measurement @Peak Dominant Wavelength λD 525 nm IF=20mA ∆λ 20 nm IF=20mA Forward Voltage VF 3.0 3.5 V IF = 20mA Reverse Current IR 10 μA VR = 5V Spectrum Radiation Bandwidth DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 3 of 15 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED Part No. : L-T650SGCT REV: A / 2 Notes: 1. Luminous intensity is measured with a light sensor and filter combination that proximities the CIE eye-response curve. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. Caution in ESD : Static Electricity and surge damages the LED. It is recommended use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. 4. Major standard testing equipment by “Instrument System” Model : CAS140B Compact Array Spectrometer and “KEITHLEY” Source Meter Model : 2400. Typical Electro-Optical Characteristics Curves Fig.1 Relative Intensity vs. Wavelength DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 4 of 15 Release Release by PARA LIGHT DCC by PARA LIGHT DCC SURFACE MOUNT DEVICE LED REV: A / 2 Part No. : L-T650SGCT Typical Electro-Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) 70 Ta=25℃ Relative Luminous lntensity Normalized of 20mA Ta=25℃ 60 50 40 30 20 10 0 2.8 3.0 3.2 3.4 3.6 Relative luminous intensity Fig.1 Forward Current vs.Forward Voltage 2 IFP=60mA 1 0.5 0.2 0.1 -40 -20 0 20 40 60 80 100 Fig.2 Relative Luminous Intensity vs.Forward Current Allowable Forward Current IFP(mA) 2.6 Ta=25℃ 100 50 30 20 10 1 5 10 20 50 100 Ambient Temperature Ta(℃) Ambient Temperature Ta(℃) Fig.3 Luminous Intensity vs.Ambient Temperature Fig.4 Forward Current Derating Curve 0° 50 Forward Current IF(mA) 200 10° 20° 30° 40 30 20 1.0 40° 0.9 50° 0.8 60° 70° 80° 90° 10 0.7 0 0 20 40 60 80 100 0.5 0.3 0.1 0.2 0.4 0.6 Ambient Temperature Ta(℃) Fig.5 Forward Current Derating Curve DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 Fig.6 Spatial Distribution DATE: 2009-10-31 PAGE 5 of 15 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED REV: A / 2 Part No. : L-T650SGCT Bin Code List Luminous Intensity(IV), Unit:mcd@20mA Bin Code Min Max P20 650 800 P21 800 P22 1000 Forward Voltage(VF), Unit:V@20mA Bin Code Min Max 14 2.9 3.0 1000 15 3.0 3.1 1250 16 3.1 3.2 17 3.2 3.3 18 3.3 3.4 19 3.4 3.5 Tolerance of each bin are±10% Tolerance of each bin are±0.1Volt Dominant Wavelength (Hue),Unit: nm@20mA Bin Code Min Max AP 520 525 AQ 525 530 Tolerance of each bin are±1nm DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 6 of 15 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED Part No. : L-T650SGCT REV: A / 2 Label Explanation CUS. PART NO: To be denominated. CUSTOMER: To be denominated. PART NO: Refer to P15 P20--- Luminous Intensity Code 15--- Forward Voltage Code AP--- Dominant Wavelength LOT NO: E L P A B 8 4 0001 C D E F A---E: For series number B---L: Local F: Foreign C---P: PLCC SMD D---Year E---Month F---SPEC. PACKING QUANTITY OF BAG : 2000pcs for T670 series 2000pcs for T650 series 2000pcs for S020 series DATE CODE：2008 G G--- Year 04 H 10 I H--- Month I --- Day DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 7 of 15 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED REV: A / 2 Part No. : L-T650SGCT Reel Dimensions Notes: 1. Taping Quantity : 2000pcs 2. The tolerances unless noted is±0.1mm, Angle±0.5°, Unit: mm. Suggest Soldering Pad Dimensions 1.12 1.80 1.34 DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 8 of 15 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED Part No. : L-T650SGCT REV: A / 2 Package Dimensions Of Tape And Reel 7 4.00∮ 0.10 (.157∮ .004) 2.00∮ 0.05 (.079∮ .002) 4.00∮ 0.10 (.157∮ .004) 3.50∮.05 (.138∮.002) (0.315+.012 -.004 ) *3.23∮0.10 (.127∮.004) *8.00+0.30 -0.10 *0.254∮ 0.020 (.0100∮ .0008) 1.75∮ 0.10 (.069∮.004) User Feed Direction *1.73∮ 0.10 (.068∮ .004) Notes: All dimensions are in millimeters. Packaging Of Electronic Components On Continuous Tapes DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 9 of 15 Release Release by PARA LIGHT DCC by PARA LIGHT DCC SURFACE MOUNT DEVICE LED REV: A / 2 Part No. : L-T650SGCT Moisture Resistant Packaging Label H:\SMD\SMD\SMD° ü × ° \± ê ? ? .jpg H:\SMD\SMD\SMD° ü × ° \± ê ? ? .jpg D\SM D\SM H :\SM .jpg ê ?? × ° \± D° ü Reel Label Desiccant Aluminum moistue-proof bag 240 H:\SM \SMD° D\SMD ü×° ? .jpg \± ê ? 145 210 5 25 Label Box 435 Carton Notes : One reel in a bag, one bag in a inner box, ten inner boxes in a carton. Unit : mm. Cleaning If cleaning is required , use the following solutions for less than 1 minute and less than 40℃. Appropriate chemicals: isopropyl alcohol. (When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not.) Effect of ultrasonic cleaning on the LED resin body differs depending on such factors as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be confirm whether any damage to the LEDS will occur. DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 10of 15 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED Part No. : L-T650SGCT ● REV: A / 2 Suggest Sn/Pb IR Reflow Soldering Profile Condition: ● Suggest Pb-Free IR Reflow Soldering Profile Condition: DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 11 of 15 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED Part No. : L-T650SGCT REV: A / 2 CAUTIONS 1. Static Electricity: * Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. * All devices, equipment and machinery must be properly grounded. It is recommended that measures be taken against surge voltage to the equipment that mounts the LEDs. * When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (blew 1mA is recommended). * Damaged LEDs will show some unusual characteristics such as the leak current remarkably increases, the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria: (VF>2.0V,at IF=0.5m A ) 2. Storage : * Before opening the package : The LEDs should be kept at 30°C or less and 85%RH or less. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. * After opening the package : The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered within 168 hours (7 days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture poof bag and to reseal the moisture proof bag again. If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should e performed using the following conditions. Baking treatment: more than 24hours at 65±5℃. * Please avoid rapid transitions in ambient temperature in high humidity environments where condensation may occur. 3. Soldering: Do not apply any stress to the LED lens during soldering while the LED is at high temperature. Recommended soldering condition. * Reflow Soldering : Pre-heat 120~150°C, 120sec. MAX., Peak temperature : 240°C Max. Soldering time : 10 sec Max. * Soldering Iron : (Not recommended) Temperature350°C Max., Soldering time : 3 sec. Max.(one time only), power dissipation of iron : 20W Max. use SN60 solder of solder with silver content and don’t to touch LED lens when soldering. DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 12 of 15 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED REV: A / 2 Part No. : L-T650SGCT 4. Lead-Free Soldering For Reflow Soldering : 1、Pre-Heat Temp: 150-180℃,120sec.Max. 2、Soldering Temp: Temperature Of Soldering Pot Over 240℃,40sec.Max. 3、Peak Temperature: 260℃，10sec. 4、Reflow Repetition: 2 Times Max. 5、Suggest Solder Paste Formula : 93.3 Sn/3.1 Ag/3.1 Bi/0.5 Cu For Soldering Iron (Not Recommended) : 1、Iron Tip Temp: 350℃ Max. 2、Soldering Iron: 30w Max. 3、Soldering Time: 3 Sec. Max. One Time. 5. Drive Method Circuit model A Circuit model B (A)Recommended circuit. (B)The difference of brightness between LED`s could be found due to the Vf-If characteristics of LED. 6. Reliability 1、Criteria For Judging The Damage Item Symbol Test Conditions Forward Voltage VF Reverse Current Luminous Intensity Criteria for Judgement MIN. Max. IF=20mA - U.S.L.*)×1.1 IR VR=5V - U.S.L.*)×2.0 IV IF=20mA L.S.L**)×0.7 - *) U.S.L.: Upper Standard Level **) L.S.L: Lower Standard Level DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 13 of 15 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED REV: A / 2 Part No. : L-T650SGCT 2、Test Items And Results Reference Standard Test Item Resistance to Soldering Heat JEITA (Reflow Soldering) ED-4701300 301 Solder ability (Reflow Soldering) Thermal Shock Temperature Cycle High Temperature Storage JEITA ED-4701300 303 JEITA ED-4701300 307 JEITA ED-4701100 105 JEITA ED-4701200201 JEITA ED-4701100 103 JEITA ED-4701200 202 Test Condition Note Tsld=260℃,10sec. 2times (Pre treatment 30 ℃,70%,168hrs) Tsld=215℃,3sec. 1time (Lead Solder) over 95% -40℃ ~ 100℃ 100cycles 30min. 30min. -40℃ ~ 25℃~100℃~25℃ 100cycles 30min. 5min. 30min. 5min Number of Damaged 0/50 0/50 0/50 0/50 Ta=100℃ 1000hrs. 0/50 Ta=60℃,RH=90% 1000hrs. 0/50 Ta=-40℃ 1000hrs. 0/50 Ta=25℃,IF=20mA 1000hrs. 0/50 Ta=85℃,IF=5mA 500hrs. 0/50 Steady State Operating Life of High Humidity Heat Ta=60℃,RH=90%,IF=15mA 500hrs. 0/50 Steady State Operating Life of Low Temperature Ta=-30℃,IF=20mA 500hrs. 0/50 100~2000~100HzSweep 4min.200m/s2 48min 0/50 Temperature Humidity Storage Low Temperature Storage Steady State Operating Life Condition Steady State Operating Life of High Temperature Vibration JEITA ED-4701400 403 3direction,4cycles Substrate Bending JEITA ED-4702 3mm,5±1sec 1time 0/50 Stick JEITA ED-4702 5N,10±1sec 1time 0/50 7.Others: The appearance and specifications of the product may be modified for improvement without notice. DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 DATE: 2009-10-31 PAGE 14 of 15 Release by PARA LIGHT DCC SURFACE MOUNT DEVICE LED REV: A / 2 Part No. : L-T650SGCT PART NO. SYSTEM : L – T 65 0 X X T - X X X X XXXX : Special specification for customer T : Taping for 7 inch reel TC : Taping for 13 inch reel Lens color C : Water Clear W : White Diffused T : Color Transparent D : Color Diffused KY : 9mil AlInGap 590nm Super Yellow KR : 9mil AlInGap 630 nm Super Red TE : 14mil AlInGap 624 nm Super Red TY: 14mil AlInGap590 nm Super Yellow LB : InGaN ITO rough 470nm Blue LG : InGaN ITO rough 520nm Green W : InGaN + YAG White color 0 : Single chip 1/2 : Super thin single chip 5/6 : Dual chip F : Three chip(Full color) C : PCB Top View Type T :PLCC Top View Type S : Side View Type DRAWING NO. : PARA-FOR-068 DS-7B-08-0003 650 : 670 : 020 : 3020 3528 3812 1.3T TYPE 1.9T TYPE 0.6T TYPE DATE: 2009-10-31 PAGE 15 of 15