LED Lighting IC LC5205D 13 October 2011 ◆Description ◆Package LC5205D is non-isolated type driver IC for LED lighting which can achieve high efficiency in simple circuitry. Its compact package which includes output MOSFET and controller, and low external components are suitable for small lighting equipment which requires saving space, like LED light bulb. Its high voltage capability allows direct connection to rectified AC supply. Protection features ensure safety LED drive. Package: DIP8 ◆Applications ◆Main Specification LED Lighting equipment LED Light bulb MOSFET Output Current Main Supply Voltage 450V (MIN), 6.0Ω (MAX) 0.5A (MAX) 450V (MAX) ◆Features DIP8Package Output MOSFET and controller are included in one package. High voltage supply input Able to direct connection to rectified AC supply. Built-in constant current controller - PWM mode current control circuitry. - Adjustable output current by input voltage to Ref pin. External PWM - PWM signal input to PWM pin enables dimming. - Low signal shuts off output current. Under voltage lockout protection (UVLO) Prevents malfunction when supply voltage is low. Over current protection (OCP) Latched in response to the load short condition. Thermal Shutdown protection (TSD) Protects IC from damage due to excess temperature, auto-restart when temperature drops below threshold Typical application circuit FUSE Input Line Filter CO Di Reg ROff R1 C1 PWM Ref COff R2 VBB LC5205 OUT GND C2 SANKEN ELECTRIC CO.,LTD. http://www.sanken-ele.co.jp 1/8 LED L Sen RS LED Lighting IC LC5205D 13 October 2011 1 Scope The present specifications shall apply to a LED driver IC for LED lighting, LC5205D. 2 Outline Type Structure Applications Hybrid Integrated Circuit Plastic Molded (Transfer Mold) LED Lighting 3 Absolute Maximum Ratings (Ta=25℃) Parameter Terminal Symbol Ratings Units Main Power Supply Voltage 6−8 VBB 450 V Output MOSFET Breakdown Voltage 5−4 Vo 450 V ※1 Output Current 5−4 IO Ref Input Voltage 3−8 VRef −0.3~VReg+0.3 V Sense Voltage 4−8 VSen -0.3~4 V Exclude tw<1µs W Mounted on PWB ※3 0.5 ※2 A Remarks Allowable Power Dissipation ― PD Junction Temperature ― Tj 150 ℃ Operating Temperature Range ― Ta −40~105 ℃ Storage Temperature Range ― Tstg −40~150 ℃ 1.73 Exclude tw<1µs ※1 Output current rating may be limited by duty cycle, ambient temperature, and heat sinking. Under any set of conditions, do not exceed the specified junction temperature (Tj). ※2 Allowable Power Dissipation depends on PWB pattern layout. ※3 Mounted on Sanken evaluation board. SANKEN ELECTRIC CO.,LTD. 2/8 LED Lighting IC LC5205D 13 October 2011 4 Electrical Characteristic (Ta=25°C, VBB=140V, Unless Otherwise Noted.) Ratings Units Remarks ― mA At enable 0.8 1.2 mA At disable 450 ― ― V ID=1mA RDS(on) ― 3.5 6.0 Ω ID=0.5A 4−5 VF ― 0.8 0.9 V IF=0.5A Reg Output Voltage 1−8 VReg 11.5 12 12.5 V IReg=0.1mA Reg Maximum Output Current 1−8 IReg ― ― 2 mA Maximum PWM Frequency 2−8 fclk 200※4 ― ― kHz Ref Input Voltage Range 3−8 VRef 0 ― 1 V Ref Input Current 3−8 IRef ― ±10 ― µA Sense Input Voltage 4−8 VSen VRef−30 VRef VRef+30 mV Sense Input Current 4−8 ISen ― ±10 ― µA Over Current Protect Voltage 4−8 VOCP ― 3 ― V Under Voltage Lock Out Threshold (Turn On) 6−8 VUVLOon ― 14 ― V Under Voltage Lock Out Threshold (Turn Off) 6−8 VUVLOoff ― 13 ― V Thermal Shutdown Threshold ― TTSD ― 150 ― °C Thermal Shutdown Hysteresis ― TTSDhys ― 55 ― °C Blanking Time ― tBLK ― 400 ― ns 5−4 tr ― 20 ― ns Io=0.4A 5−4 tf ― 50 ― ns Io=0.4A Parameter Terminal Symbol 6−8 MIN TYP MAX IBB ― 2 6−8 IBBs ― Drain-Source Breakdown Voltage 5−4 VDS(BR) Output MOS-FET On Resistance 5−4 Body Diode Forward Voltage Main Power Supply Current Switching Time ※4 Operation at a PWM frequency greater than 200kHz is possible but not warranted. SANKEN ELECTRIC CO.,LTD. 3/8 duty=50% Temperature of Control IC LED Lighting IC LC5205D 13 October 2011 Thermal Data Temperature Rise Δ T [℃] 150 125 Δ Tj-a= 72×PD 100 75 Δ Tc-a= 60×PD 50 25 0 0 0.5 1 1.5 2 Total Power Dissipation P D[W] Power Dissipation versus Ambient Temperature Allowable Package Power Dissipation PD [W] 2 P D =1.73W 1.5 θ j-a= 72℃/W 1 0.5 0 0 10 20 30 40 50 60 70 80 90 Ambient Temperature Ta [℃] 100 110 120 SANKEN ELECTRIC CO.,LTD. 4/8 LED Lighting IC LC5205D 13 October 2011 5 Functional Block Diagram (Pin assignment) VBB OUT MIC Reg Regulator UVLO TSD PWM Ref Current Control Logic Gate Driver OCP GND Sen Pin Assignment Number Name Function 1 Reg 12V Internal regulator output pin 2 PWM Connect to PWM Off-Time Setting C&R 3 Ref Reference Voltage for PWM Control 4 Sen Output-current detection pin 5 OUT Output pin 6 VBB Supply voltage pin 7 - ― 8 GND Device ground pin. SANKEN ELECTRIC CO.,LTD. 5/8 LED Lighting IC LC5205D 13 October 2011 6 Package 6.1 Package Drawing and Material DIP8 Package LC5205 SK D Dimensions in mm Terminal material: Cu Terminal treatment: Solder plating (Pb-free) Marking Position Contents Indication ① The last digit of the year 0 to 9 ② The Month 1 to 9,O,N,D ③ The week 1 to 3 Sanken Registration Number alphanumeric characters ④ ⑤ ⑥ ⑦ 6.2 Appearance The body shall be clean and shall not bear any stain, rust or flaw. 6.3 Marking The type number and lot number shall be clearly marked by laser so that cannot be erased easily. SANKEN ELECTRIC CO.,LTD. 6/8 LED Lighting IC LC5205D 13 October 2011 7 Cautions and warnings Since reliability can be affected adversely by improper storage environment and handling methods during Characteristic tests, please observe the following cautions. 7.1 Cautions for Storage Ensure that storage conditions comply with the standard temperature (5 to 35℃) and the standard relative humidity (around 40 to 75%) and avoid storage locations that experience extreme changes in temperature or humidity. Avoid locations where dust or harmful gases are present and avoid direct sunlight. Reinspect for rust in leads and solderability that have been stored for a long time. 7.2 Cautions for characteristic Tests and Handling When characteristic tests are carried out during inspection testing and other standard tests periods, protect the devices from surge of power from the testing device, shorts between the devices and the heatsink. 7.3 Considerations to protect the Products from Electrostatic Discharge When handling the devices, operator must be grounded. Grounded wrist straps be worn and should have at least 1MΩ of resistance near operators to ground to prevent shock hazard. Workbenches where the devices are handled should be grounded and be provided with conductive table and floor mats. When using measuring equipment such as a curve tracer, the equipment should also be grounded. When soldering the devices, the head of a soldering iron or a solder bath must be grounded in other to prevent leak voltage generated by them from being applied to the devices. The devices should always be stored and transported in our shipping containers or conductive containers, or be wrapped up in aluminum foil. SANKEN ELECTRIC CO.,LTD. 7/8 LED Lighting IC LC5205D 13 October 2011 7.4 Others The contents in this document are subject to changes, for improvement and other purposes, without notice. Make sure that this is the latest revision of the document before use. Application and operation examples described in this document are quoted for the sole purpose of reference for the use of the products herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or any other rights of Sanken or any third party which may result from its use. Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction. Sanken products listed in this document are designed and intended for the use as components in general purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest Sanken sales representative to discuss, prior to the use of the products herein. The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited. In the case that you use our semiconductor devices or design your products by using our semiconductor devices, the reliability largely depends on the degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation range is set by derating the load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. In general, derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stresses such as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor devices. For these stresses, instantaneous values, maximum values and minimum values must be taken into consideration. In addition, it should be noted that since power devices or IC’s including power devices have large self-heating value, the degree of derating of junction temperature (Tj) affects the reliability significantly. When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, chemically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. Anti radioactive ray design is not considered for the products listed herein. Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken’s distribution network. The contents in this document must not be transcribed or copied without Sanken’s written consent. SANKEN ELECTRIC CO.,LTD. 8/8