3 V, LVDS, Quad CMOS Differential Line Receiver ADN4666 ±8 kV ESD IEC 61000-4-2 contact discharge on receiver input pins 400 Mbps (200 MHz) switching rates 100 ps channel-to-channel skew (typical) 100 ps differential skew (typical) 3.3 ns propagation delay (maximum) 3.3 V power supply High impedance outputs on power-down Low power design (10 mW quiescent typical) Interoperable with existing 5 V LVDS drivers Accepts small swing (350 mV typical) differential input signal levels Supports open, short, and terminated input fail-safe Conforms to TIA/EIA-644 LVDS standard Industrial operating temperature range of −40°C to +85°C Available in surface-mount SOIC package and low profile TSSOP package FUNCTIONAL BLOCK DIAGRAM ADN4666 VCC RIN1– RIN4– RIN1+ RIN4+ R1 R4 ROUT1 ROUT4 EN EN ROUT2 ROUT3 R2 R3 RIN2+ RIN3+ RIN2– RIN3– GND 08097-001 FEATURES Figure 1. APPLICATIONS Point-to-point data transmission Multidrop buses Clock distribution networks Backplane receivers GENERAL DESCRIPTION The ADN4666 is a quad-channel, CMOS low voltage differential signaling (LVDS) line receiver offering data rates of over 400 Mbps (200 MHz) and ultralow power consumption. The device accepts low voltage (350 mV typical) differential input signals and converts them to a single-ended, 3 V TTL/CMOS logic level. The ADN4666 also offers active high and active low enable/disable inputs (EN and EN) that control all four receivers. These inputs disable the receivers and switch the outputs to a high impedance state. Consequently, the outputs of one or more ADN4666 devices can be multiplexed together to reduce the quiescent power consumption to 10 mW typical. The ADN4666 and its companion driver, the ADN4665, offer a new solution to high speed, point-to-point data transmission and offer a low power alternative to emitter-coupled logic (ECL) or positive emitter-coupled logic (PECL). Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2009 Analog Devices, Inc. All rights reserved. ADN4666 TABLE OF CONTENTS Features .............................................................................................. 1 ESD Caution...................................................................................6 Applications ....................................................................................... 1 Pin Configuration and Function Descriptions..............................7 Functional Block Diagram .............................................................. 1 Typical Performance Characteristics ..............................................8 General Description ......................................................................... 1 Theory of Operation .........................................................................9 Revision History ............................................................................... 2 Enable Inputs .................................................................................9 Specifications..................................................................................... 3 Applications Information .............................................................9 Timing Specifications .................................................................. 4 Outline Dimensions ....................................................................... 10 Absolute Maximum Ratings............................................................ 6 Ordering Guide .......................................................................... 10 REVISION HISTORY 6/09—Revision 0: Initial Version Rev. 0 | Page 2 of 12 ADN4666 SPECIFICATIONS VCC = 3.0 V to 3.6 V, CL = 15 pF to GND, all specifications TMIN to TMAX, unless otherwise noted. 1, 2 Table 1. Parameter LVDS INPUTS (RINx+, RINx−) Differential Input High Threshold at RINx+, RINx− 3 Differential Input Low Threshold at RINx+, RINx−3 Common-Mode Voltage Range at RINx+, RINx− 4 Input Current at RINx+, RINx− Symbol VTH VTL VCMR IIN Input High Voltage Input Low Voltage Input Current Input Clamp Voltage OUTPUTS (ROUTx) Output High Voltage VIH VIL IIN VCL Output Low Voltage Output Short-Circuit Current 5 Output Off State Current POWER SUPPLY No Load Supply, Current Receivers Enabled No Load Supply, Current Receivers Disabled VOL IOS IOZ ESD PROTECTION RINx+, RINx− Pins All Pins Except RINx+, RINx− Min VOH ICC ICCZ Typ Max Unit Test Conditions/Comments 20 100 mV VCM = 1.2 V, 0.05 V, 2.95 V 2.3 +10 +10 +20 VCC 0.8 +10 mV V μA μA μA V V μA V VCM = 1.2 V, 0.05 V, 2.95 V VID = 200 mV p-p VIN = 2.8 V, VCC = 3.6 V or 0 V VIN = 0 V, VCC = 3.6 V or 0 V VIN = 3.6 V, VCC = 0 V IOH = −0.4 mA, VID = 200 mV IOH = −0.4 mA, input terminated IOH = −0.4 mA, input shorted IOL = 2 mA, VID = −200 mV Outputs enabled, VOUT = 0 V Outputs disabled, VOUT = 0 V or VCC −100 0.1 −10 −10 −20 2.0 GND −10 −1.5 −20 2.7 2.7 2.7 3.0 3.0 3.0 0.1 −48 ±1 0.25 −120 +10 V V V V mA μA 10 3 15 5 mA mA EN and EN = VCC or GND, inputs open EN = GND and EN = VCC, inputs open kV kV kV IEC 61000-4-2 contact discharge Human body model Human body model −15 −10 ±5 ±1 ±1 ±1 −0.8 ±8 ±15 ±4 1 VIN = 0 V or VCC, other input = VCC or GND ICL = −18 mA Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground, unless otherwise specified. All typical values are given for VCC = 3.3 V and TA = 25°C. 3 VCC is always higher than the RINx+ and RINx− voltage. RINx− and RINx+ have a voltage range of −0.2 V to VCC − VID/2. However, to be compliant with ac specifications, the common-mode voltage range is 0.1 V to 2.3 V. 4 VCMR is reduced for larger input differential voltage (VID). For example, if VID is 400 mV, VCMR is 0.2 V to 2.2 V. The fail-safe condition with inputs shorted is not supported over the common-mode range of 0 V to 2.4 V, but is supported only with inputs shorted and no external common-mode voltage applied. VID up to VCC − 0 V can be applied to the RINx+/RINx− inputs with the common-mode voltage set to VCC/2. Propagation delay and differential pulse skew decrease when VID is increased from 200 mV to 400 mV. Skew specifications apply for 200 mV ≤ VID ≤ 800 mV over the common-mode range. 5 Output short-circuit current (IOS) is specified as magnitude only; a minus sign indicates direction only. Note that only one output should be shorted at a time; do not exceed the maximum junction temperature specification (150°C). 2 Rev. 0 | Page 3 of 12 ADN4666 TIMING SPECIFICATIONS VCC = 3.0 V to 3.6 V, CL = 15 pF to GND, all specifications TMIN to TMAX, unless otherwise noted. 1 Table 2. Parameter 2 AC CHARACTERISTICS Differential Propagation Delay, High to Low Differential Propagation Delay, Low to High Differential Pulse Skew 6 |tPHLD − tPLHD| Differential Channel-to-Channel Skew (Same Device) 7 Differential Part-to-Part Skew 8 Differential Part-to-Part Skew 9 Rise Time Fall Time Disable Time, High to Z Disable Time, Low to Z Enable Time, Z to High Enable Time, Z to Low Maximum Operating Frequency 10 Symbol Min tPHLD tPLHD tSKD1 tSKD2 1.8 1.8 0 0 tSKD3 tSKD4 tTLH tTHL tPHZ tPLZ tPZH tPZL fMAX 200 Typ 3 Max Unit Test Conditions/Comments 4, 5 0.1 0.1 3.3 3.3 0.35 0.5 ns ns ns ns CL = 15 pF, VID = 300 mV (see Figure 2 and Figure 3) CL = 15 pF, VID = 300 mV (see Figure 2 and Figure 3) CL = 15 pF, VID = 300 mV (see Figure 2 and Figure 3) CL = 15 pF, VID = 300 mV (see Figure 2 and Figure 3) 1.0 1.5 1.2 1.2 12 12 17 17 ns ns ns ns ns ns ns ns MHz CL = 15 pF, VID = 300 mV (see Figure 2 and Figure 3) CL = 15 pF, VID = 300 mV (see Figure 2 and Figure 3) CL = 15 pF, VID = 300 mV (see Figure 2 and Figure 3) CL = 15 pF, VID = 300 mV (see Figure 2 and Figure 3) RL = 2 kΩ, CL = 15 pF (see Figure 4 and Figure 5) RL = 2 kΩ, CL = 15 pF (see Figure 4 and Figure 5) RL = 2 kΩ, CL = 15 pF (see Figure 4 and Figure 5) RL = 2 kΩ, CL = 15 pF (see Figure 4 and Figure 5) All channels switching 0.35 0.35 8 8 11 11 250 Generator waveform for all tests, unless otherwise specified: f = 1 MHz, ZO = 50 Ω, tTLH and tTHL (0% to 100%) ≤ 3 ns for RINx+/RINx−. AC parameters are guaranteed by design and characterization. 3 All typical values are given for VCC = 3.3 V and TA = 25°C. 4 Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground, unless otherwise specified. 5 CL includes load and jig capacitance. 6 tSKD1 is the magnitude difference in the differential propagation delay time between the positive-going edge and the negative-going edge of the same channel. 7 Channel-to-channel skew, tSKD2, is defined as the difference between the propagation delay of one channel and that of the others on the same chip with any event on the inputs. 8 tSKD3 part-to-part skew is the differential channel-to-channel skew of any event between devices. The tSKD3 specification applies to devices at the same VCC and within 5°C of each other within the operating temperature range. 9 tSKD4 part-to-part skew is the differential channel-to-channel skew of any event between devices. The tSKD4 specification applies to devices over the recommended operating temperature and voltage ranges and across process distribution. tSKD4 is defined as |maximum − minimum| differential propagation delay. 10 fMAX generator input conditions: f = 200 MHz, tTLH = tTHL < 1 ns (0% to 100%), 50% duty cycle, differential (1.05 V to 1.35 V p-p). fMAX generator output criteria: 60%/40% duty cycle, VOL (maximum = 0.4 V), VOH (minimum = 2.7 V), and load = 15 pF (stray plus probes). 1 2 Test Circuits and Timing Diagrams VCC RINx+ SIGNAL GENERATOR ROUTx RINx– 50Ω 50Ω CL NOTES 1. CL = LOAD AND TEST JIG CAPACITANCE. 08097-002 RECEIVER IS ENABLED Figure 2. Test Circuit for Receiver Propagation Delay and Transition Time Rev. 0 | Page 4 of 12 ADN4666 RINx– 1.3V 0V (DIFFERENTIAL) 1.2V VID = 300mV p-p RINx+ 1.1V tPLHD tPHLD VOH 80% 1.5V 1.5V 20% 20% tTLH VOL tTHL 08097-003 ROUTx 80% Figure 3. Receiver Propagation Delay and Transition Time Waveforms VCC S1 RL RINx+ ROUTx CL RINx– EN SIGNAL GENERATOR 50Ω EN NOTES 1. CL INCLUDES LOAD AND TEST JIG CAPACITANCE. 2. S1 CONNECTED TO VCC FOR tPZL AND tPLZ MEASUREMENTS. 3. S1 CONNECTED TO GND FOR tPZH AND tPHZ MEASUREMENTS. 08097-004 GND Figure 4. Test Circuit for Receiver Enable/Disable Delay 3V EN WITH EN = GND OR OPEN CIRCUIT 1.5V 1.5V 0V 3V EN WITH EN = VCC 1.5V 1.5V 0V tPHZ tPZH VOH 0.5V 50% ROUTx WITH VID = +100mV GND VCC ROUTx WITH VID = –100mV 0.5V tPLZ tPZL Figure 5. Receiver Enable/Disable Delay Waveforms Rev. 0 | Page 5 of 12 VOL 08097-005 50% ADN4666 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 3. Parameter VCC to GND Input Voltage (RINx+, RINx−) to GND Enable Input Voltage (EN, EN) to GND Output Voltage (ROUTx) to GND Industrial Operating Temperature Range Storage Temperature Range Maximum Junction Temperature (TJ MAX) θJA Thermal Impedance Power Dissipation Reflow Soldering Peak Temperature, Pb-Free Rating −0.3 V to +4 V −0.3 V to VCC + 0.3 V −0.3 V to VCC + 0.3 V −0.3 V to VCC + 0.3 V −40°C to +85°C −65°C to +150°C 150°C 150.4°C/W (TJ MAX − TA)/θJA 260°C ± 5°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION Rev. 0 | Page 6 of 12 ADN4666 RIN1– 1 16 VCC 2 15 RIN4– RIN1+ ROUT1 3 EN 4 ROUT2 5 ADN4666 14 RIN4+ TOP VIEW (Not to Scale) 13 ROUT4 12 EN RIN2+ 6 11 ROUT3 RIN2– 7 10 RIN3+ GND 8 9 RIN3– 08097-006 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 6. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 Mnemonic RIN1− 2 RIN1+ 3 ROUT1 4 EN 5 ROUT2 6 RIN2+ 7 RIN2− 8 9 GND RIN3− 10 RIN3+ 11 ROUT3 12 EN 13 ROUT4 14 RIN4+ 15 RIN4− 16 VCC Description Receiver Channel 1 Inverting Input. When this input is more negative than RIN1+, ROUT1 is high. When this input is more positive than RIN1+, ROUT1 is low. Receiver Channel 1 Noninverting Input. When this input is more positive than RIN1−, ROUT1 is high. When this input is more negative than RIN1−, ROUT1 is low. Receiver Channel 1 Output (3 V TTL/CMOS). If the differential input voltage between RIN1+ and RIN1− is positive, this output is high. If the differential input voltage is negative, this output is low. Active High Enable and Power-Down Input (3 V TTL/CMOS). When EN is low and EN is high, the receiver outputs are disabled and are in a high impedance state. When EN is high and EN is low or when EN is low and EN is low, the receiver outputs are enabled. When EN is high and EN is high, the receiver outputs are enabled. Receiver Channel 2 Output (3 V TTL/CMOS). If the differential input voltage between RIN2+ and RIN2− is positive, this output is high. If the differential input voltage is negative, this output is low. Receiver Channel 2 Noninverting Input. When this input is more positive than RIN2−, ROUT2 is high. When this input is more negative than RIN2−, ROUT2 is low. Receiver Channel 2 Inverting Input. When this input is more negative than RIN2+, ROUT2 is high. When this input is more positive than RIN2+, ROUT2 is low. Ground Reference Point for All Circuitry on the Part. Receiver Channel 3 Inverting Input. When this input is more negative than RIN3+, ROUT3 is high. When this input is more positive than RIN3+, ROUT3 is low. Receiver Channel 3 Noninverting Input. When this input is more positive than RIN3−, ROUT3 is high. When this input is more negative than RIN3−, ROUT3 is low. Receiver Channel 3 Output (3 V TTL/CMOS). If the differential input voltage between RIN3+ and RIN3− is positive, this output is high. If the differential input voltage is negative, this output is low. Active Low Enable and Power-Down Input with Pull-Down (3 V TTL/CMOS). ). When EN is low and EN is high, the receiver outputs are disabled and are in a high impedance state. When EN is high and EN is low or when EN is low and EN is low, the receiver outputs are enabled. When EN is high and EN is high, the receiver outputs are enabled. Receiver Channel 4 Output (3 V TTL/CMOS). If the differential input voltage between RIN4+ and RIN4− is positive, this output is high. If the differential input voltage is negative, this output is low. Receiver Channel 4 Noninverting Input. When this input is more positive than RIN4−, ROUT4 is high. When this input is more negative than RIN4−, ROUT4 is low. Receiver Channel 4 Inverting Input. When this input is more negative than RIN4+, ROUT4 is high. When this input is more positive than RIN4+, ROUT4 is low. Power Supply Input. The ADN4666 can be operated from 3.0 V to 3.6 V. Rev. 0 | Page 7 of 12 ADN4666 80 200 70 150 60 3.6V SUPPLY 100 3.3V SUPPLY 3.6V SUPPLY 40 3V SUPPLY 50 30 0 3V SUPPLY –50 20 –100 10 –150 0 0.01 0.1 1 10 FREQUENCY (MHz) 100 1k –200 –0.1 Figure 7. Power Supply Current vs. Frequency 0.4 0.9 1.4 1.9 2.4 2.9 COMMON-MODE VOLTAGE (V) 3.4 3.9 08097-010 3.3V SUPPLY SKEW (ps) 50 08097-007 POWER SUPPLY CURRENT (mA) TYPICAL PERFORMANCE CHARACTERISTICS Figure 10. Skew vs. Common-Mode Voltage, 25°C 2.8 2.7 3 COMMON-MODE VIN (V) 3V SUPPLY 2.6 2.5 2.4 3.3V SUPPLY 2.3 2.2 2 1 3.6V SUPPLY 0.4 0.9 1.4 1.9 2.4 2.9 COMMON-MODE VOLTAGE (V) 3.4 3.9 0 –0.1 Figure 8. Differential Propagation Delay (tPLHD) vs. Common-Mode Voltage, 25°C 2.9 2.7 3V SUPPLY 2.5 3.3V SUPPLY 2.3 3.6V SUPPLY 1.9 –0.1 0.4 0.9 1.4 1.9 2.4 2.9 COMMON-MODE VOLTAGE (V) 3.4 3.9 08097-009 2.1 Figure 9. Differential Propagation Delay (tPHLD) vs. Common-Mode Voltage, 25°C Rev. 0 | Page 8 of 12 0 0.1 0.2 0.3 0.4 VID (V) 0.5 0.6 0.7 Figure 11. Typical Common-Mode Range Variation with Respect to the Amplitude of the Differential Input 0.8 08097-011 2.0 1.9 –0.1 DIFFERENTIAL PROPAGATION DELAY (ns) VCC = 3.3V TA = 25°C fIN = 100MHz 2 CHANNELS SWITCHING MAX PROP DELAY MEASURED, tPHLD , tPLHD = 2.54ns MAX SKEW MEASURED | tPLHD – tPHLD | = 280ps 2.1 08097-008 DIFFERENTIAL PROPAGATION DELAY (ns) 2.9 ADN4666 THEORY OF OPERATION A differential current input signal, received via a transmission medium such as a twisted pair cable, develops a voltage across a termination resistor, RT. This resistor is chosen to match the characteristic impedance of the medium, typically around 100 Ω. The differential voltage is detected by the receiver and converted back into a single-ended logic signal. When the noninverting receiver input, RINx+, is positive with respect to the inverting input, RINx− (that is, when current flows through RT from RINx+ to RINx−), ROUTx is high. When the noninverting receiver input, RINx+, is negative with respect to the inverting input, RINx− (that is, when current flows through RT from RINx− to RINx+), ROUTx is low. Using the ADN4665 as a driver, the received differential current is between ±2.5 mA and ±4.5 mA (±3.5 mA typical), developing between ±250 mV and ±450 mV across a 100 Ω termination resistor. The received voltage is centered around the receiver offset of 1.2 V. Therefore, the noninverting receiver input is typically 1.375 V (that is, 1.2 V + [350 mV/2]) and the inverting receiver input is 1.025 V (that is, 1.2 V − [350 mV/2]) for a Logic 1. For a Logic 0, the inverting and noninverting input voltages are reversed. Note that because the differential voltage reverses polarity, the peak-to-peak voltage swing across RT is twice the differential voltage. Current-mode drivers offer considerable advantages over voltagemode drivers, such as the RS-422 drivers. The operating current remains fairly constant with increased switching frequency, whereas the operating current of voltage-mode drivers increases exponentially in most cases. This increase is caused by the overlap as internal gates switch between high and low, causing currents to flow from VCC to ground. A current-mode device reverses a constant current between its two outputs, with no significant overlap currents. This is similar to emitter-coupled logic (ECL) and positive emittercoupled logic (PECL), but without the high quiescent current of ECL and PECL. ENABLE INPUTS The ADN4666 has active high and active low enable inputs that put all the logic outputs into a high impedance state when disabled, reducing device current consumption from 10 mA typical to 3 mA typical. See Table 5 for a truth table of the enable inputs. Table 5. Enable Inputs Truth Table EN Pin Logic Level EN Low Low Low High High 1 RINx+ RINx− 1 High Low Low Low Low 1 X 1.025 V 1.375 V 1.025 V 1.375 V X 1.375 V 1.025 V 1.375 V 1.025 V ROUTx High-Z 0 1 0 1 X = don’t care. APPLICATIONS INFORMATION Figure 12 shows a typical application for point-to-point data transmission using the ADN4665 as the driver and the ADN4666 as the receiver. 1/4 ADN4666 1/4 ADN4665 EN EN EN EN DOUTx+ RT 100Ω DINx Rev. 0 | Page 9 of 12 RINx+ DOUTx– GND ROUTx RINx– GND Figure 12. Typical Application Circuit 08097-022 The ADN4666 is a quad-channel line receiver for low voltage differential signaling (LVDS). It takes a differential input signal of 350 mV typical and converts it into a single-ended, 3 V TTL/ CMOS logic signal. ADN4666 OUTLINE DIMENSIONS 10.00 (0.3937) 9.80 (0.3858) 4.00 (0.1575) 3.80 (0.1496) 9 16 1 6.20 (0.2441) 5.80 (0.2283) 8 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0039) COPLANARITY 0.10 0.50 (0.0197) 0.25 (0.0098) 1.75 (0.0689) 1.35 (0.0531) SEATING PLANE 0.51 (0.0201) 0.31 (0.0122) 45° 8° 0° 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-AC 060606-A CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 13. 16-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-16) Dimensions shown in millimeters and (inches) 5.10 5.00 4.90 16 9 4.50 4.40 4.30 6.40 BSC 1 8 PIN 1 1.20 MAX 0.15 0.05 0.20 0.09 0.65 BSC 0.30 0.19 COPLANARITY 0.10 SEATING PLANE 8° 0° 0.75 0.60 0.45 COMPLIANT TO JEDEC STANDARDS MO-153-AB Figure 14. 16-Lead Thin Shrink Small Outline Package [TSSOP] (RU-16) Dimensions shown in millimeters ORDERING GUIDE Model ADN4666ARZ 1 ADN4666ARZ-REEL71 ADN4666ARUZ1 ADN4666ARUZ-REEL71 1 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 16-Lead Thin Standard Small Outline Package [SOIC_N] 16-Lead Thin Standard Small Outline Package [SOIC_N] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] Z = RoHS Compliant Part. Rev. 0 | Page 10 of 12 Package Option R-16 R-16 RU-16 RU-16 ADN4666 NOTES Rev. 0 | Page 11 of 12 ADN4666 NOTES ©2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D08097-0-6/09(0) Rev. 0 | Page 12 of 12