CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS TM NPCAP PSG - Radial Lead Upgrade! Series ・Super low ESR, high ripple current capability ・Endurance: 15,000 to 20,000 hours at 105℃ ・Rated voltage : 16 to 25Vdc ・RoHS Compliant ・Halogen Free PSG Downsized PSF P52 ◆SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Capacitance Tolerance Surge Voltage Leakage Current -55 to +105℃ 16 to 25Vdc ±20% (M) Rated voltage(V)×1.15 I=0.2CV or 500µA, whichever is greater Where, I : Leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V) *Note Dissipation Factor (tanδ) Low Temperature Characteristics (Max.Impedance Ratio) Endurance Bias Humidity Test Surge Voltage Test Failure Rate (at 20℃, 120Hz) (at 105℃) (at 20℃ after 2 minutes) 0.12 max. (at 20℃, 120Hz) Z(-25℃)/Z(+20℃)≦1.15 Z(-55℃)/Z(+20℃)≦1.25 (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 20,000 hours (20, 25V : 15,000 hours) at 105℃. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦150% of the initial specified value ESR ≦150% of the initial specified value Leakage current ≦The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦150% of the initial specified value Leakage current ≦The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦150% of the initial specified value Leakage current ≦The initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105℃) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃. ◆DIMENSIONS [mm] ●Terminal Code : E F05,F08,H06,H08 φD' φd F±0.5 Coated Case L' 15min. Size code F05 F08 H06 H08 φD 6.3 φd 0.45 F 2.5 φD' L' L+1.0max. (Note1) HB5,H16,H20,JB5,J16,J20 H20 JB5 0.6 3.5 φD+0.5max. J16 10.0 J20 5.0 L+1.5max. F±0.5 ◆MARKING EX) 16V150µF φD' φd H16 Note1 : L+1.2 max. for 16V270µF (Rated ripple current 5,080mArms). 4min. Coated Case HB5 8.0 G 6D6 150 16V L' 15min. 4min. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 48 CAT. No. E1001P CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS TM NPCAP Radial Lead PSGSeries Upgrade! - ◆PART NUMBERING SYSTEM 1 2 3 4 A PSG 5 6 7 8 E 9 10 11 12 13 14 M 15 16 17 18 S (Note2) : PSG series, 16V270μF (Rated ripple current 5,080mArms) ,16V470μF (Rated ripple current 5,400mArms) ,16V560μF (Rated ripple current 6,100mArms)have supplement code “J”. Terminal and terminal plating are the same as all other inPSG series. Supplement code Size code Capacitance tolerance code Capacitance code (ex. 150µF:151,1,000µF:102) Lead forming·Taping code Terminal code Voltage code (ex. 16V:160,20V:200) Series code Category Please refer to “Product code guide (conductive polymer type)” ◆STANDARD RATINGS WV (Vdc) 16 20 25 Cap (µF) Case size φD×L (mm) ESR (mΩ max./20℃, 100k to 300kHz) Rated ripple current (mArms/105℃, 100kHz) Part No. 150 270 270 270 470 470 560 560 820 820 1,000 1,000 1,200 1,500 1,800 2,200 120 180 330 390 680 56 82 180 180 220 330 390 6.3×5 6.3 ×8 6.3×8 8×6 8×8 8×8 8×11.5 8×11.5 8× 16 10×11.5 8 ×20 10× 11.5 8 ×20 10× 16 10× 20 10× 20 6.3×5 6.3× 8 8×8 8 × 11.5 10× 11.5 6.3×5 6.3 × 8 8×8 8×11.5 8× 11.5 10×11.5 10× 11.5 20 10 15 22 8 16 8 14 8 12 8 12 8 8 8 8 20 18 17 14 12 30 28 18 16 16 14 14 3,200 5,080 3,800 3,300 5,400 4,000 6,100 4,970 7,000 5,400 7,500 5,400 7,500 7,700 8,100 8,100 3,200 3,460 3,880 4,970 5,400 2,600 2,780 3,770 4,650 4,650 5,000 5,000 APSG160E□□151MF05S APSG160E□□271MF08J APSG160E□□271MF08S APSG160E□□271MH06S APSG160E□□471MH08J APSG160E□□471MH08S APSG160E□□561MHB5J APSG160E□□561MHB5S APSG160E□□821MH16S APSG160E□□821MJB5S APSG160E□□102MH20S APSG160E□□102MJB5S APSG160E□□122MH20S APSG160E□□152MJ16S APSG160E□□182MJ20S APSG160E□□222MJ20S APSG200E□□121MF05S APSG200E□□181MF08S APSG200E□□331MH08S APSG200E□□391MHB5S APSG200E□□681MJB5S APSG250E□□560MF05S APSG250E□□820MF08S APSG250E□□181MH08S APSG250E□□181MHB5S APSG250E□□221MHB5S APSG250E□□331MJB5S APSG250E□□391MJB5S □□ : Enter the appropriate lead forming or taping code. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 49 CAT. No. E1001P