GP2A25J0000F Series GP2A25J0000F Series Detecting Distance : 1 to 9mm *OPIC Output, Reflective Photointerrupter with Connector ■ Description ■ Agency approvals/Compliance GP2A25J0000F Series are OPIC output, reflective photointerrupters with emitter and detector facing the same direction in a molding that provides non-contact sensing. This family of devices uses light modulation to reduce the affects of disturbing light, and the sensor is optimized to work in the selected focal distance. A 3-pin connector is included to allow remote-mount or off-board designs. 1. Compliant with RoHS directive ■ Applications 1. General purpose detection of paper presence or motion. 2. Example : PPC, FAX, Printer ■ Features 1. Reflective with OPIC Light Modulated Output 2. Highlights : • Includes additional screw fixing holes • Position pin to prevent mis-alignment • Short focal distance 3. Key Parameters: • Detecting distance : 1 to 9mm (White paper) 3 to 7mm (Black paper) • Undetecting distance : over 27mm (White paper) • Connector : GP2A25J0000F ; Tyco Electronics AMP K.K. (PN : 292133-3) GP2A25DJ000F ; Tyco Electronics AMP K.K. (PN : 292133-3) GP2A25NJJ00F ; Tyco Electronics AMP K.K. (PN : 4-292133-3) 4. Lead free and RoHS directive compliant * "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and a signalprocessing Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 1 Sheet No.: D3-A04901EN Date Jun. 30. 2005 © SHARP Corporation GP2A25J0000F Series ■ Internal Connection Diagram Demodulator circuit Reflective object 1 Voltage regulator 1 2 2 3 VCC VOUT GND Amp. 3 Comparator Oscillator circuit Sync. detecting circuit ■ Outline Dimensions (Unit : mm) GP2A25DJ000F 33 26.5 9 2 3 6.2 VCC VOUT GND 6.1 9.6 7 3.5 4.5 1 φ3.2 φ3+0 −0.2 Optical center 17.7 3.1 2 GP2A25J0000F 1 2 3 φ3.2 6 Connector : 292133-3 (Tyco Electronics AMP K.K.) VCC VOUT GND 12 12 Connector : 292133-3 (Tyco Electronics AMP K.K.) 7.8 7.5 Optical center 6 1 2 3 26.5 7 Product mass : approx. 1.95g 9 4.5 7.8 4.3 2 1 3.5 • Unspecified tolerance shall be as follows ; 4-SR2 Dimensions Tolerance less than 6 ±0.2 6 or more less ±0.3 than 14 14 or more ±0.4 Date code 7.9 26.5 34.3 • Unspecified tolerance shall be as follows ; 0 φ3+0 −0.2 φ3.2 2 φ3+0 −0.2 2 2.5 9 8 4.5 8 4.5 3 6 Date code Product mass : approx. 2.4g Dimensions Tolerance less than 6 ±0.2 6 or more less ±0.3 than 14 14 or more ±0.4 GP2A25NJJ00F Optical center (6.8) 33 17.7 9 (7.8) 4.5 3.1 φ3.2 6.2 1 2 3 VCC VOUT GND 6 12 Connector : 4-292133-3 (Tyco Electronics AMP K.K.) φ3+0 −0.2 26.5 0 7 Date code • ( ) : Reference dimensions. • : Portion Built-in IR-90 filter Product mass : approx. 1.95g 1 2 3 2 2.5 8 4.5 (5 .8) 7.8 • Unspecified tolerance shall be as follows ; Dimensions Tolerance less than 6 ±0.2 6 or more less ±0.3 than 14 14 or more ±0.4 Connector terminal plating material : Sn Sheet No.: D3-A04901EN 2 GP2A25J0000F Series Date code (2 digit) 1st digit Year of production A.D. Mark 2000 0 2001 1 2002 2 2003 3 2004 4 2005 5 2006 6 2007 7 2008 8 2009 9 2010 0 : : 2nd digit Month of production Month Mark 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 X 11 Y 12 Z repeats in a 10 year cycle Country of origin Japan Sheet No.: D3-A04901EN 3 GP2A25J0000F Series ■ Absolute Maximum Ratings Parameter Supply voltage Output voltage *1 Output current *2 Operating temperature *2 Storage temperature ∗ ∗ Symbol VCC VO IOL Topr Tstg Rating −0.5 to +7 30 50 −10 to +60 −20 to +80 (Ta=25˚C) Unit V V mA ˚C ˚C 1 Sink current refer to Fig.5. 2 The connector should be plugged in/out at normal temperature. ■ Electro-optical Characteristics Parameter Supply voltage Current dissipation (I) *3 Current dissipation (II) Low level output voltage High level output voltage *4 Non detection distance Symbol VCC ICC ICCP VOL VOH LLHL LHLS *4 Detection distance LHLL *5 Response time *6 Acceptable illuminance Condhitions − Smoothing value VCC=5V, RL=∞ Pulse peak value VCC=5V VCC=5V, IOL=16mA, at detecting time VCC=5V, RL=1kΩ, at non detecting time KODAK Gray Cards, VCC=5V KODAK Gray Cards, VCC=5V Black paper, VCC=5V KODAK Gray Cards, VCC=5V Black paper, VCC=5V tPLH tPHL Ev1 Ev2 VCC=5V − MIN. 4.75 − − − 4.5 − − − 9 7 − − 3 000 1 500 TYP. − − − − − − − − − − − − − − MAX. 5.25 30 150 0.4 − 27 1 3 − − 1 1 − − (Ta=25˚C) Unit V mA mA V V mm mm mm ms ms lx lx ∗ 3 Refer to Fig.1. 4 Refer to Fig.2. ∗ 5 Refer to Fig.3. * 6 Refer to Fig.4. ∗ Reflective object Black paper (black) : Standard reflective object (provided by SHARP Corporation) KODAK Gray Cards (use the white side reflects about 90%) : Standard reflective object (provided by SHARP Corporation) PPC paper : Standard reflective object (provided by SHARP Corporation) Sheet No.: D3-A04901EN 4 GP2A25J0000F Series Fig.1 Test Condition for Peak Pulse Value ICCP R=1Ω 1 VCC=5V Vr RL=1kΩ V 2 VO 3 GND tW ICCP=Vr/1Ω tP(TYP.)=130μs tW(TYP.)=8μs tP Photointerrupter Fig.2 Test Condition for Detecting Distance Characteristics Output VO Reflective object VOH VOL Detecting distance L LHLS LHLL Detection surface LLHS LLHL Fig.3 Test Circuit for Response Time Reflective object With reflective object RL=1kΩ Detection surface 1 VCC=5V 2 VO 3 GND Without reflective object tPHL tPLH VOH Vout waveform L 1.5V VOL Photointerrupter Fig.4 Test Condition for External Disturbing Light Illuminance EV1 : At non-detecting EV2 : At detecting Emission/detection surface Emission/detection surface Light source A PPC paper Light source A Photointerrupter Photointerrupter Illuminance shall be that on the reflective object. Output shall not go from "L" to "H". 7mm Illuminance shall be that on the emission/detection surface. Output shall not go from "H" to "L". Sheet No.: D3-A04901EN 5 GP2A25J0000F Series Fig.5 Low Level Output Current vs. Ambient Temperature Fig.6 Low Level Output Voltage vs. Ambient Temperature 0.3 VCC=5V At detecting 50 Low level output voltage VOL (V) Low level output current IOL(mA) 60 40 30 27 20 10 0 −10 IOL=30mA 0.2 16mA 0.1 5mA 0 0 25 50 60 75 −10 25 50 75 Ambient temperature Ta (˚C) Ambient temperature Ta (˚C) Fig.8 Dissipation Current(Smoothing Value) vs. Ambient Temperature Fig.7 Low Level Output Voltage vs. Low Level Output Current 7 VCC=5V At detecting 6 Dissipation current ICC (mA) Low level output voltage VOL (V) 0 0.1 Ta=−10˚C 5 25˚C 4 60˚C 3 2 1 0.01 1 10 0 4.75 100 Low level output current IOL (mA) 5 5.25 Supply voltage VCC (V) Remarks : Please be aware that all data in the graph are just for reference and not for guarantee. Sheet No.: D3-A04901EN 6 GP2A25J0000F Series ■ Design Considerations ● Design guide 1) VO terminal : Open collector output This product operates the light emitter by pulse drive. Please supply the stable supply voltage in order to prevent error operation by pulse current. Please use this device after connecting a capacitor between VO and GND for prevention of line noise. 2) Prevention of detection error Please be careful that you need to keep the direct inverter light away from the photo detecting surface since the device will not operate correctly in such case. In addition, we recommend to make sure the operation test in the actual application. 3) Plugging in/out The connector should be plugged in/out at normal temperature. This product is not designed against irradiation and incorporates non-coherent IRED. ● Parts This product is assembled using the below parts. • Photodetector (Q'ty : 1) [Using a silicon photodiode as light detecting portion, and a bipolar IC as signal processing circuit] Category Maximum Sensitivity wavelength (nm) Sensitivity wavelength (nm) Response time (μs) Photodiode 900 700 to 1 200 400 • Photo emitter (Q'ty : 1) Category Material Maximum light emitting wavelength (nm) I/O Frequency (MHz) Infrared emitting diode (non-coherent) Gallium arsenide (GaAs) 950 0.3 • Material Case Lens Polycarbonate resin (Black) (UL94 V-2) GP2A25J0000F GP2A25DJ000J Bottom cover Black polyphernylene Sulfide resin (UL94 V-0) Acryl resin (UL94 HB) Polycarbonate resin (Black) (UL94 V-2) Polycarbonate resin (Black) (UL94 V-2) GP2A25NJJ00F∗ ∗The IR-90 filter (Fuji Photo Film Co., Ltd.) is inserted between case and detector side lens. • Others Laser generator is not used. Sheet No.: D3-A04901EN 7 GP2A25J0000F Series ■ Manufacturing Guidelines ● Cleaning instructions Polycarbonate resin is used as the material of the lens surface. So this product shall not be cleaned by cleaning solvent absolutely. Dust and stain shall clean by air blow, or shall clean by soft cloth. ● Presence of ODC This product shall not contain the following materials. And they are not used in the production process for this product. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC). •Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated diphenyl ethers (PBDE). Sheet No.: D3-A04901EN 8 GP2A25J0000F Series ■ Package specification ● Case package Package materials Anti-static plastic bag : Polyethtylene Moltopren : Urethane Packing case : Corrugated fiberboard Package method 100 pcs of products shall be packaged in a plastic bag, Ends shall be sealed by stapler. The bottom ot the packing case is covered with moltopren, and 2 plastic bags shall be put int the packing case. Moltopren should be located after all product are settled (1 packing conteains 200 pcs). Packing composition Moltopren Anti-static plastic bag Packing case Sheet No.: D3-A04901EN 9 GP2A25J0000F Series ■ Important Notices · The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). · Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. · If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. · Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection · This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. · Contact and consult with a SHARP representative if there are any questions about the contents of this publication. Sheet No.: D3-A04901EN [H174] 10