NLX2G02 Dual 2-Input NOR Gate The NLX2G02 is an advanced high-speed dual 2-input CMOS NOR gate in ultra-small footprint. The NLX2G02 input structures provide protection when voltages up to 7.0 volts are applied, regardless of the supply voltage. http://onsemi.com Features • • • • • • • High Speed: tPD 2.5 ns (typical) at VCC = 5.0 V Designed for 1.65 V to 5.5 V VCC Operation Low Power Dissipation: ICC = 1 mA (Max) at TA = 25°C 24 mA Balanced Output Sink and Source Capability Balanced Propagation Delays Overvoltage Tolerant (OVT) Input Pins This is a Pb−Free Device A1 B1 Y2 GND 1 8 2 7 3 6 4 5 MARKING DIAGRAMS 1 ULLGA8 1.45 x 1.0 CASE 613AA TM G 1 ULLGA8 1.6 x 1.0 CASE 613AB AKM G ULLGA8 1.95 x 1.0 CASE 613AC AKM G 1 VCC XX M G Y1 PIN ASSIGNMENT B2 A2 Figure 1. Pinout IEEE/IEC A1 B1 & A2 B2 = Specific Device Code = Date Code = Pb−Free Package Pin Function 1 A1 2 B1 3 Y2 4 GND 5 A2 6 B2 7 Y1 8 VCC FUNCTION TABLE Y1 Y=A+B Y2 Inputs Figure 2. Logic Symbol Output A B Y L L H L H H H L H H H L H = HIGH Logic Level L = LOW Logic Level ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. © Semiconductor Components Industries, LLC, 2009 December, 2009 − Rev. 0 1 Publication Order Number: NLX2G02/D NLX2G02 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage *0.5 to +7.0 V VIN DC Input Voltage *0.5 to +7.0 V *0.5 to VCC + 7.0 V VIN < GND *50 mA VOUT < GND *50 mA VOUT Parameter DC Output Voltage IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Source/Sink Current $50 mA ICC DC Supply Current per Supply Pin $100 mA IGND DC Ground Current per Ground Pin $100 mA TSTG Storage Temperature Range *65 to )150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C TJ Junction Temperature Under Bias 150 °C qJA Thermal Resistance (Note 1) N/A °C/W PD Power Dissipation in Still Air at 85°C N/A mW MSL Moisture Sensitivity FR Flammability Rating VESD ILatchup Level 1 Oxygen Index: 28 to 34 ESD Withstand Voltage UL 94 V−0 @ 0.125 in Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) Latchup Performance Above VCC and Below GND at 125°C (Note 5) 2000 > 200 N/A V $500 mA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2−ounce copper trace with no air flow. 2. Tested to EIA/JESD22−A114−A. 3. Tested to EIA/JESD22−A115−A. 4. Tested to JESD22−C101−A. 5. Tested to EIA/JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Max Unit 1.65 1.5 5.5 5.5 V VCC Power DC Supply Voltage VIN Digital Input Voltage (Note 6) 0 5.5 V Output Voltage 0 VCC V −55 +125 °C 0 0 0 0 20 20 10 5 ns/V VOUT TA Operating Free−Air Temperature Dt/DV Input Transition Rise or Fall Rate Operating Data Retention Only Min VCC = 1.8 V $0.15 V VCC = 2.5 V $0.2 V VCC = 3.3 V $0.3 V VCC = 5.0 V $0.5 V 6. Unused inputs may not be left open. All inputs must be tied to a high− or low−logic input voltage level. http://onsemi.com 2 NLX2G02 DC ELECTRICAL CHARACTERISTICS Symbol Parameter VIH High−Level Input Voltage VIL VOH Condition 1.65 2.3 to 5.5 Low−Level Input Voltage High−Level Output Voltage Low−Level Output Voltage Min Typ VIN = VIH or VIL, IOH = −100 mA VIN = VIH or VIL, IOL = 100 mA Max Min Max 0.75 x VCC 0.7 x VCC 0.25 x VCC 0.3 x VCC 2.3 to 5.5 TA = −555C to +1255C TA 3 855C 0.75 x VCC 0.7 x VCC 1.65 VIN = VIH or VIL IOH = −4 mA IOH = −8 mA IOH = −12 mA IOH = −16 mA IOH = −24 mA IOH = −32 mA VOL VCC (V) TA = 255C Min 0.75 x VCC 0.7 x VCC 0.25 x VCC 0.3 x VCC VCC − 0.1 VCC VCC − 0.1 VCC − 0.1 1.65 2.3 2.7 3.0 3.0 4.5 1.29 1.9 2.2 2.4 2.3 3.8 1.5 2.1 2.4 2.7 2.5 4.0 1.29 1.9 2.2 2.4 2.3 3.8 1.29 1.9 2.2 2.4 2.3 3.8 Unit V 0.25 x VCC 0.3 x VCC 1.65 to 5.5 1.65 to 5.5 Max V V 0.1 0.1 0.1 0.24 0.3 0.4 0.4 0.55 0.55 0.24 0.3 0.4 0.4 0.55 0.55 0.24 0.3 0.4 0.4 0.55 0.55 V VIN = VIH or VIL IOL = 4 mA IOL = 8 mA IOL = 12 mA IOL = 16 mA IOL = 24 mA IOL = 32 mA 1.65 2.3 2.7 3.0 3.0 4.5 Input Leakage Current 0 ≤ VIN ≤ 5.5 V 0 to 5.5 $0.1 $1.0 $1.0 mA IOFF Power−Off Input Leakage Current VIN = 5.5 V 0 1.0 10 10 mA ICC Quiescent Supply Current 0 ≤ VIN ≤ 5.5 V 5.5 1.0 10 10 mA IIN 0.08 0.20 0.22 0.28 0.38 0.42 AC ELECTRICAL CHARACTERISTICS tR = tF = 2.5 ns TA = 255C VCC Symbol tPLH tPHL Parameter Propagation Delay Input A to Output TA 3 855C (V) Test Condition Min Typ Max Min Max 1.65 to 1.95 RL = 1 MW, CL = 15 pF 2.0 7.4 9.5 2.0 9.7 2.3 to 2.7 RL = 1 MW, CL = 15 pF 1.2 3.3 5.4 1.2 5.8 3.0 to 3.6 RL = 1 MW, CL = 15 pF 0.8 2.6 3.9 0.8 4.3 RL = 500 W, CL = 50 pF 1.2 3.2 4.8 1.2 5.2 RL = 1 MW, CL = 15 pF 0.5 1.9 3.1 0.5 3.3 RL = 500 W, CL = 50 pF 0.8 2.5 3.7 0.8 4.0 4.5 to 5.5 TA = −555C to +1255C Min Max Unit ns CIN Input Capacitance 5.5 VIN = 0 V or VCC 2.5 pF CPD Power Dissipation Capacitance (Note 7) 3.3 5.5 10 MHz, VIN = 0V or VCC 9 11 pF 7. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no−load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. http://onsemi.com 3 NLX2G02 tf = 3 ns tf = 3 ns 90% INPUT A and B VCC 90% 50% INPUT 50% 10% 10% tPHL GND OUTPUT RL CL tPLH VOH OUTPUT Y 50% A 1−MHz square input wave is recommended for propagation delay tests. 50% VOL Figure 3. Switching Waveform Figure 4. Test Circuit ORDERING INFORMATION Package Shipping† NLX2G02AMX1TCG ULLGA8, 1.95 x 1.0, 0.5P (Pb−Free) 3000 / Tape & Reel NLX2G02BMX1TCG ULLGA8, 1.6 x 1.0, 0.4P (Pb−Free) 3000 / Tape & Reel NLX2G02CMX1TCG ULLGA8, 1.45 x 1.0, 0.35P (Pb−Free) 3000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 4 NLX2G02 PACKAGE DIMENSIONS ULLGA8 1.45x1.0, 0.35P CASE 613AA−01 ISSUE A ÉÉÉ ÉÉÉ ÉÉÉ PIN ONE REFERENCE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.10 C 0.05 C A 8X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX −−− 0.40 0.00 0.05 0.15 0.25 1.45 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 7X 0.48 8X 0.22 e/2 e 1 7X L NOTE 4 4 1.18 L1 0.53 8 5 8X b 0.05 C PKG OUTLINE 0.35 PITCH DIMENSIONS: MILLIMETERS 0.10 C A B BOTTOM VIEW 1 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 http://onsemi.com 5 NLX2G02 PACKAGE DIMENSIONS ULLGA8 1.6x1.0, 0.4P CASE 613AB−01 ISSUE A PIN ONE REFERENCE 0.10 C 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D ÉÉÉ ÉÉÉ ÉÉÉ E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 8X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX −−− 0.40 0.00 0.05 0.15 0.25 1.60 BSC 1.00 BSC 0.40 BSC 0.25 0.35 0.30 0.40 7X 0.49 e/2 e 1 4 8 5 7X L NOTE 4 1.24 L1 0.53 8X b 0.05 C 1 PKG OUTLINE 0.40 PITCH DIMENSIONS: MILLIMETERS 0.10 C A B BOTTOM VIEW 8X 0.26 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 http://onsemi.com 6 NLX2G02 PACKAGE DIMENSIONS ULLGA8 1.95x1.0, 0.5P CASE 613AC−01 ISSUE A PIN ONE REFERENCE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D ÉÉÉÉ ÉÉÉÉ ÉÉÉÉ E DIM A A1 b D E e L L1 TOP VIEW 0.10 C 0.05 C MILLIMETERS MIN MAX −−− 0.40 0.00 0.05 0.15 0.25 1.95 BSC 1.00 BSC 0.50 BSC 0.25 0.35 0.30 0.40 A 8X 0.05 C MOUNTING FOOTPRINT SOLDERMASK DEFINED* SEATING PLANE SIDE VIEW 7X C A1 0.49 8X 0.30 e/2 e 7X L NOTE 4 4 1 1.24 L1 0.53 8 5 8X BOTTOM VIEW b 0.10 C A B 0.05 C 1 PKG OUTLINE 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 7 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLX2G02/D