AD AD7403BRIZ-RL 16-bit, isolated sigma-delta modulator Datasheet

16-Bit, Isolated Sigma-Delta Modulator
AD7403
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAM
VDD1
BUF
VDD2
CLK
DECODER
CLK
ENCODER
DATA
ENCODER
DATA
DECODER
REF
VIN+
MCLKIN
(5MHz
TO 20MHz)
Σ-Δ ADC
VIN–
MDAT
AD7403
GND1
GND2
12196-001
5 MHz to 20 MHz external clock input rate
16 bits, no missing codes
Signal-to-noise ratio (SNR): 88 dB typical
Effective number of bits (ENOB): 14.2 bits typical
Offset drift vs. temperature
AD7403: 1.6 µV/°C typical
AD7403-8: 2 µV/°C typical
On-board digital isolator
On-board reference
Full-scale analog input range: ±320 mV
Operating range
AD7403: −40°C to + 125°C
AD7403-8: −40°C to + 105°C
High common-mode transient immunity: >25 kV/µs
Wide-body SOIC with increased creepage package
Slew rate limited output for low EMI
Safety and regulatory approvals
UL recognition
5000 V rms for 1 minute per UL 1577
CSA Component Acceptance Notice 5A
VDE Certificate of Conformity
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
VIORM = 1250 VPEAK
Figure 1.
APPLICATIONS
Shunt current monitoring
AC motor controls
Power and solar inverters
Wind turbine inverters
Data acquisition systems
Analog-to-digital and optoisolator replacements
GENERAL DESCRIPTION
The AD7403 is a high performance, second-order, Σ-Δ modulator
that converts an analog input signal into a high speed, single-bit
data stream, with on-chip digital isolation based on Analog
Devices, Inc., iCoupler® technology. The device operates from a
5 V (VDD1) power supply and accepts a differential input signal
of ±250 mV (±320 mV full-scale). The differential input is ideally
suited to shunt voltage monitoring in high voltage applications
where galvanic isolation is required.
1
The analog input is continuously sampled by a high performance
analog modulator, and converted to a ones density digital output
stream with a data rate of up to 20 MHz. The original
1
information can be reconstructed with an appropriate digital
filter to achieve 88 dB signal to noise ratio (SNR) at 78.1 kSPS.
The serial input/output can use a 5 V or a 3 V supply (VDD2).
The serial interface is digitally isolated. High speed complementary
metal oxide semiconductor (CMOS) technology, combined with
monolithic transformer technology, means the on-chip isolation
provides outstanding performance characteristics, superior to
alternatives such as optocoupler devices. The AD7403 device is
offered in a 16-lead, wide-body SOIC package and has an operating temperature range of −40°C to +125°C. The AD7403-8
device is offered in an 8-lead, wide-body SOIC package and has
an operating temperature range of −40°C to +105°C.
Protected by U.S. Patents 5,952,849; 6,873,065; and 7,075,329.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2014–2015 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD7403* Product Page Quick Links
Last Content Update: 11/01/2016
Comparable Parts
Reference Materials
View a parametric search of comparable parts
Informational
• ADSP-CM40x in Solar PV Inverters
Press
• Highest Accuracy Isolated Sigma-Delta Modulator
Increases Efficiency of Motor Drives and Power Inverters
Technical Articles
• A Networked Approach To Improving Energy Efficiency In
Manufacturing Automation Systems
• A System Approach to Understanding the Impact of
Nonideal Effects in a Motor Drive Current Loop
• Functional Safety for Integrated Circuits Used in Variable
Speed Drives
• MS-2652: Measurement Techniques for Industrial Motion
Control
• MS-2758: Enhancing Industrial Motor Control Performance
Utilizing Digital Isolator Technology
• Sigma-Delta Conversion Used for Motor Control
Evaluation Kits
• AD-FMCMOTCON2-EBZ Evaluation Board
• AD7403 Evaluation Board
• Evaluation board for evaluating FlexMC Motor Control
Low Voltage Kit
• Evaluation board for evaluating FlexMC Motor Control
Universal AC Kit
• Isolated Inverter Platform Evaluation Board
Documentation
Application Notes
• AN-1316: Generating Multiple Isolated Bias Rails for
IGBT Motor Drives with Flyback, SEPIC, and Ćuk
Combination
• AN-1377: Gain and Offset Temperature Drift
Compensation for the AD7403/AD7405
Data Sheet
• AD7403-EP: Enhanced Product Data Sheet
• AD7403: 16-Bit, Isolated Sigma-Delt Modulator Data Sheet
User Guides
• UG-683: Evaluating the AD7403 16-Bit, Isolated SigmaDelta ADC
Design Resources
•
•
•
•
AD7403 Material Declaration
PCN-PDN Information
Quality And Reliability
Symbols and Footprints
Discussions
Software and Systems Requirements
View all AD7403 EngineerZone Discussions
• EVAL-FMCMOTCON2 Evaluation Software
Sample and Buy
Tools and Simulations
Visit the product page to see pricing options
• AD7403 MatLab Model
• AD7403 IBIS Model
• AD7403-8 IBIS Model
Technical Support
Submit a technical question or find your regional support
number
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet. Note: Dynamic changes to
the content on this page does not constitute a change to the revision number of the product data sheet. This content may be
frequently modified.
AD7403
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 15
Applications ....................................................................................... 1
Circuit Information.................................................................... 15
Functional Block Diagram .............................................................. 1
Analog Input ............................................................................... 15
General Description ......................................................................... 1
Differential Inputs ...................................................................... 16
Revision History ............................................................................... 2
Digital Output ............................................................................. 16
Specifications..................................................................................... 3
Applications Information .............................................................. 17
AD7403 .......................................................................................... 3
Current Sensing Applications ................................................... 17
AD7403-8 ...................................................................................... 4
Voltage Sensing Applications .................................................... 17
Timing Specifications .................................................................. 5
Input Filter................................................................................... 18
Package Characteristics ............................................................... 6
Digital Filter ................................................................................ 18
Insulation and Safety Related Specifications ............................ 6
Interfacing to ADSP-CM4xx .................................................... 21
Regulatory Information ............................................................... 6
Power Supply Considerations ................................................... 21
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 Insulation
Characteristics .............................................................................. 7
Grounding and Layout .............................................................. 21
Absolute Maximum Ratings............................................................ 8
Outline Dimensions ....................................................................... 23
ESD Caution .................................................................................. 8
Ordering Guide .......................................................................... 24
Insulation Lifetime ..................................................................... 21
Pin Configurations and Function Descriptions ........................... 9
Typical Performance Characteristics ........................................... 10
Terminology .................................................................................... 14
REVISION HISTORY
5/15—Rev. A to Rev. B
Added AD7403-8 ................................................................ Universal
Added Endnote 3, Table 1 ............................................................... 4
Added Table 2; Renumbered Sequentially .................................... 4
Added Figure 4 .................................................................................. 7
Added Figure 6 and Table 11........................................................... 9
Added Figure 8 ................................................................................ 10
Added Figure 14 and Figure 18..................................................... 11
Added Figure 20.............................................................................. 12
Added Power Supply Considerations Section, Figure 41, and
Figure 42 .......................................................................................... 21
Added Figure 47, Outline Dimensions ........................................ 23
Changes to Ordering Guide .......................................................... 24
11/14—Rev. 0 to Rev. A
Change to Figure 1 ............................................................................1
Changes to Regulatory Information Section and Table 5 ............5
Changes to Table 7.............................................................................7
Changes to Ordering Guide .......................................................... 20
4/14—Revision 0: Initial Version
Rev. B | Page 2 of 24
Data Sheet
AD7403
SPECIFICATIONS
AD7403
VDD1 = 4.5 V to 5.5 V, VDD2 = 3 V to 5.5 V, VIN+ = −250 mV to +250 mV, VIN− = 0 V, TA = −40°C to +125°C, fMCLKIN1 = 5 MHz to 20 MHz,
tested with sinc3 filter, 256 decimation rate, as defined by Verilog code, unless otherwise noted. All voltages are relative to their respective
ground.
Table 1.
Parameter
STATIC PERFORMANCE
Resolution
Integral Nonlinearity (INL)2
Differential Nonlinearity (DNL)2
Offset Error2
Offset Drift vs. Temperature3
Min
Noise Free Code Resolution2
ISOLATION TRANSIENT IMMUNITY2
LOGIC INPUTS
Input High Voltage (VIH)
Input Low Voltage (VIL)
Input Current (IIN)
Input Capacitance (CIN)
LOGIC OUTPUTS
Output High Voltage (VOH)
Output Low Voltage (VOL)
±12
±0.99
±0.75
3.8
3.1
−320
−250
Input Common-Mode Voltage Range
Dynamic Input Current
Signal-to-Noise Ratio (SNR)2
Total Harmonic Distortion (THD)2
Peak Harmonic or Spurious Noise (SFDR)2
Effective Number of Bits (ENOB)2
±2
±0.2
1.6
1.3
50
±0.2
±0.2
±0.2
65
40
±0.6
Gain Error Drift vs. Temperature3
DC Leakage Current
Input Capacitance
DYNAMIC SPECIFICATIONS
Signal-to-Noise-and-Distortion Ratio (SINAD)2
Max
16
Offset Drift vs. VDD13
Gain Error2
Gain Error Drift vs. VDD13
ANALOG INPUT
Input Voltage Range
Typ
±0.8
±0.8
±1.2
95
60
+320
+250
−200 to +300
±45
0.05
±0.01
14
±50
±0.6
Unit
Test Conditions/Comments
Bits
LSB
LSB
mV
µV/°C
µV/°C
µV/V
% FSR
% FSR
% FSR
ppm/°C
µV/°C
mV/V
Filter output truncated to 16 bits
mV
mV
mV
µA
µA
µA
pF
Guaranteed no missed codes to 16 bits
0°C to 85°C
fMCLKIN = 16 MHz
fMCLKIN = 20 MHz, TA = −40°C to +85°C
fMCLKIN = 20 MHz
Full-scale range
For specified performance
VIN+ = ±250 mV, VIN− = 0 V
VIN+ = 0 V, VIN− = 0 V
VIN+ = 1 kHz
81
83
86
13.1
13.4
14
25
87
87
88
−96
−97
14.2
14.2
dB
dB
dB
dB
dB
Bits
Bits
Bits
kV/µs
30
−40°C to +85°C
−40°C to +85°C
CMOS with Schmitt trigger
0.8 × VDD2
0.2 × VDD2
±0.6
10
V
V
µA
pF
0.4
V
V
VDD2 − 0.1
Rev. B | Page 3 of 24
IO = −200 µA
IO = +200 µA
AD7403
Parameter
POWER REQUIREMENTS
VDD1
VDD2
IDD1
IDD2
Data Sheet
Min
2
3
Max
Unit
Test Conditions/Comments
30
12
6
231
185
5.5
5.5
36
18
10
297
231
V
V
mA
mA
mA
mW
mW
VDD1 = 5.5 V
VDD2 = 5.5 V
VDD2 = 3.3 V
VDD1 = VDD2 = 5.5 V
VDD1 = 5.5 V, VDD2 = 3.3 V
4.5
3
Power Dissipation
1
Typ
For fMCLKIN > 16 MHz, mark space ratio is 48/52 to 52/48, VDD1 = 5 V ± 5%.
See the Terminology section.
Not production tested. Sample tested during initial release to ensure compliance.
AD7403-8
VDD1 = 4.5 V to 5.5 V, VDD2 = 3 V to 5.5 V, VIN+ = −250 mV to +250 mV, VIN− = 0 V, TA = −40°C to +105°C, fMCLKIN1 = 5 MHz to 20 MHz,
tested with sinc3 filter, 256 decimation rate, as defined by Verilog code, unless otherwise noted. All voltages are relative to their respective
ground.
Table 2.
Parameter
STATIC PERFORMANCE
Resolution
Integral Nonlinearity (INL)2
Differential Nonlinearity (DNL)2
Offset Error2
Offset Drift vs. Temperature3
Offset Drift vs. VDD13
Gain Error2
Min
±2
±6.5
±0.99
±1.7
6.8
±1
2
425
±0.2
±0.2
32
20
±0.2
−320
−250
Input Common-Mode Voltage Range
Dynamic Input Current
DC Leakage Current
Input Capacitance
DYNAMIC SPECIFICATIONS
Signal-to-Noise-and-Distortion Ratio (SINAD)2
Signal-to-Noise Ratio (SNR)2
Total Harmonic Distortion (THD)2
Peak Harmonic or Spurious Noise (SFDR)2
Effective Number of Bits (ENOB)2
ISOLATION TRANSIENT IMMUNITY2
LOGIC INPUTS
Input High Voltage (VIH)
Input Low Voltage (VIL)
Input Current (IIN)
Input Capacitance (CIN)
LOGIC OUTPUTS
Output High Voltage (VOH)
Output Low Voltage (VOL)
Max
16
Gain Error Drift vs. Temperature3
Gain Error Drift vs. VDD13
ANALOG INPUT
Input Voltage Range
Typ
±0.8
±1.4
80
51
+320
+250
−200 to +300
±45
0.05
±0.01
14
±50
±0.6
Unit
Test Conditions/Comments
Bits
LSB
LSB
mV
µV/°C
µV/V
% FSR
% FSR
ppm/°C
µV/°C
mV/V
Filter output truncated to 16 bits
mV
mV
mV
µA
µA
µA
pF
Guaranteed no missed codes to 16 bits
fMCLKIN = 16 MHz
fMCLKIN = 20 MHz
Full-scale range
For specified performance
VIN+ = ±250 mV, VIN− = 0 V
VIN+ = 0 V, VIN− = 0 V
VIN+ = 1 kHz
82
86
13.3
25
87
88
−94
−94
14.2
30
dB
dB
dB
dB
Bits
kV/µs
CMOS with Schmitt trigger
0.8 × VDD2
0.2 × VDD2
±0.6
10
V
V
µA
pF
0.4
V
V
VDD2 − 0.1
Rev. B | Page 4 of 24
IO = −200 µA
IO = +200 µA
Data Sheet
AD7403
Parameter
POWER REQUIREMENTS
VDD1
VDD2
IDD1
IDD2
Min
2
3
Max
Unit
Test Conditions/Comments
30
13
6.5
237
187
5.5
5.5
33.5
16
8
272
211
V
V
mA
mA
mA
mW
mW
VDD1 = 5.5 V
VDD2 = 5.5 V
VDD2 = 3.3 V
VDD1 = VDD2 = 5.5 V
VDD1 = 5.5 V, VDD2 = 3.3 V
4.5
3
Power Dissipation
1
Typ
For fMCLKIN > 16 MHz, mark space ratio is 48/52 to 52/48, VDD1 = 5 V ± 5%.
See the Terminology section.
Not production tested. Sample tested during initial release to ensure compliance.
TIMING SPECIFICATIONS
VDD1 = 4.5 V to 5.5 V, VDD2 = 3 V to 5.5 V, TA = −40°C to +105°C (AD7403-8) or −40°C to +125°C (AD7403), unless otherwise noted.
Sample tested during initial release to ensure compliance. It is recommended to read MDAT on the MCLKIN rising edge.
Table 3.
Parameter
fMCLKIN
Limit at TMIN, TMAX
Typ Max
20
Unit
MHz
MHz
40
45
42
ns
ns
ns
1
1
Data access time after MCLKIN rising edge
VDD2 = 4.5 V to 5.5 V
VDD2 = 3 V to 3.6 V, AD7403
VDD2 = 3 V to 3.6 V, AD7403-8
Data hold time after MCLKIN rising edge
VDD2 = 4.5 V to 5.5 V
VDD2 = 3 V to 3.6 V
Master clock low time
fMCLKIN ≤ 16 MHz
16 MHz < fMCLKIN ≤ 20 MHz
Master clock high time
fMCLKIN ≤ 16 MHz
16 MHz < fMCLKIN ≤ 20 MHz
t21
12
17
ns
ns
0.45 × tMCLKIN
0.48 × tMCLKIN
ns
ns
0.45 × tMCLKIN
0.48 × tMCLKIN
ns
ns
t3
t4
1
Description
Master clock input frequency
Defined as the time required from an 80% MCLKIN input level to when the output crosses 0.8 V or 2.0 V for VDD2 = 3 V to 3.6 V or when the output crosses 0.8 V or 0.7 ×
VDD2 for VDD2 = 4.5 V to 5.5 V as outlined in Figure 2. Measured with a ±200 μA load and a 25 pF load capacitance.
t4
80%
MCLKIN
t1
t2
t3
2.0V OR 0.7 × VDD2 1
MDAT
0.8V
1SEE
NOTE 1 OF TABLE 3 FOR FURTHER DETAILS.
Figure 2. Data Timing
Rev. B | Page 5 of 24
12196-002
t
Min
5
AD7403
Data Sheet
PACKAGE CHARACTERISTICS
Table 4.
Parameter
Resistance (Input to Output)1
Capacitance (Input to Output)1
IC Junction to Ambient Thermal Resistance
1
Symbol
RI-O
CI-O
θJA
Min
Typ
1012
2.2
45
Max
Unit
Ω
pF
°C/W
Test Conditions/Comments
f = 1 MHz
Thermocouple located at center of package underside,
test conducted on 4-layer board with thin traces
The device is considered a 2-terminal device. For AD7403, Pin 1 to Pin 8 are shorted together and Pin 9 to Pin 16 are shorted together. For AD7403-8, Pin 1 to Pin 4 are
shorted together, Pin 5 to Pin 8 are shorted together.
INSULATION AND SAFETY RELATED SPECIFICATIONS
Table 5.
Parameter
Input to Output Momentary Withstand Voltage
Minimum External Air Gap (Clearance)
AD7403
AD7403-8
Minimum External Tracking (Creepage)
AD7403
AD7403-8
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Isolation Group
1
2
3
Symbol
VISO
Value
5000 min
Unit
V
Test Conditions/Comments
1 minute duration
L(I01)
8.3 min1, 2
mm
L(I01)
8.1 min1, 2
mm
Measured from input terminals to output
terminals, shortest distance through air
Measured from input terminals to output
terminals, shortest distance through air
L(I02)
8.3 min1
mm
L(I02)
8.1 min1
mm
CTI
0.034 min
>400
II
mm
V
Measured from input terminals to output
terminals, shortest distance path along body
Measured from input terminals to output
terminals, shortest distance path along body
Distance through insulation
DIN IEC 112/VDE 0303 Part 13
Material Group (DIN VDE 0110, 1/89, Table I)3
In accordance with IEC 60950-1 guidelines for the measurement of creepage and clearance distances for a pollution degree of 2 and altitudes ≤2000 m.
Consideration must be given to pad layout to ensure the minimum required distance for clearance is maintained.
CSA CTI rating for the AD7403 is >600 V and a Material Group I isolation group. AD7403-8 is >400 and a Material Group II isolation group.
REGULATORY INFORMATION
Table 6.
UL1
Recognized under 1577
Component Recognition
Program1
5000 V rms Isolation Voltage
Single Protection
File E214100
CSA
Approved under CSA Component Acceptance Notice 5A
VDE2
Certified according to DIN V VDE V 0884-10
(VDE V 0884-10):2006-122
Basic insulation per CSA 60950-1-07 and IEC 60950-1,
AD7403: 830 V rms (1173 VPEAK), AD7403-8: 810 Vrms
(1145 VPEAK) maximum working voltage3
Reinforced insulation per CSA 60950-1-07 and
IEC 60950-1. AD7403: 415 V rms (586 VPEAK), AD7403-8:
405 V rms (583 VPEAK) maximum working voltage3
Reinforced insulation per IEC 60601-1, 250 V rms
(353 VPEAK) maximum working voltage
File 205078
Reinforced insulation per DIN V VDE V 0884-10
(VDE V 0884-10):2006-12, 1250 VPEAK
File 2471900-4880-0001
In accordance with UL 1577, each AD7403 is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (current leakage detection limit = 15 µA).
In accordance with DIN V VDE V 0884-10, each AD7403 is proof tested by applying an insulation test voltage ≥ 2344 VPEAK for 1 second (partial discharge detection limit = 5 pC).
3
Rating is calculated for a pollution degree of 2 and a Material Group III. The AD7403 RI-16-2 package material is rated by CSA to a CTI of >600 V and therefore
Material Group I. The AD7403-8 RI-8-1 package material is rated by CSA to a CTI of >400 V and therefore Material Group II.
1
2
Rev. B | Page 6 of 24
Data Sheet
AD7403
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 INSULATION CHARACTERISTICS
This isolator is suitable for reinforced electrical isolation only within the safety limit data. Maintenance of the safety data is ensured by
means of protective circuits.
Table 7.
Description
INSTALLATION CLASSIFICATION PER DIN VDE 0110
For Rated Mains Voltage ≤300 V rms
For Rated Mains Voltage ≤450 V rms
For Rated Mains Voltage ≤600 V rms
For Rated Mains Voltage ≤1000 V rms
CLIMATIC CLASSIFICATION
POLLUTION DEGREE (DIN VDE 0110, TABLE 1)
MAXIMUM WORKING INSULATION VOLTAGE
INPUT TO OUTPUT TEST VOLTAGE, METHOD B1
VIORM × 1.875 = VPR, 100% Production Test, tm = 1 Second, Partial Discharge < 5 pC
INPUT TO OUTPUT TEST VOLTAGE, METHOD A
After Environmental Test Subgroup 1
VIORM × 1.6 = VPR, tm = 60 Seconds, Partial Discharge < 5 pC
After Input and/or Safety Test Subgroup 2/ Safety Test Subgroup 3
VIORM × 1.2 = VPR, tm = 60 Seconds, Partial Discharge < 5 pC
HIGHEST ALLOWABLE OVERVOLTAGE (TRANSIENT OVERVOLTAGE, tTR = 10 Seconds)
SURGE ISOLATION VOLTAGE
1.2 µs Rise Time, 50 μs, 50% Fall Time
SAFETY LIMITING VALUES (MAXIMUM VALUE ALLOWED IN THE EVENT OF A FAILURE, SEE Figure 3
AND Figure 4)
Case Temperature
Side 1 (PVDD1) and Side 2 (PVDD2) Power Dissipation
AD7403
AD7403-8
INSULATION RESISTANCE AT TS, VIO = 500 V
Characteristic
Unit
VIORM
I to IV
I to IV
I to IV
I to IV
40/105/21
2
1250
VPEAK
2344
VPEAK
2000
VPEAK
1500
8000
12000
VPEAK
VPEAK
VPEAK
VPEAK
150
°C
2.78
1.19
>109
W
W
Ω
VPD(M)
VPR(M)
VIOTM
VIOSM
TS
PSO
RIO
3
2
1
0
0
50
100
150
AMBIENT TEMPERATURE (°C)
200
1
0
0
Figure 3. AD7403 Thermal Derating Curve, Dependence of Safety Limiting
Values with Case Temperature per DIN V VDE V 0884-10
50
100
150
AMBIENT TEMPERATURE (°C)
200
12196-041
SAFE OPERATING POWER (W)
2
12196-003
SAFE OPERATING POWER (W)
4
Symbol
Figure 4. AD7403-8 Thermal Derating Curve, Dependence of Safety Limiting
Values with Case Temperature per DIN V VDE V 0884-10
Rev. B | Page 7 of 24
AD7403
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted. All voltages are relative to
their respective ground.
Table 8.
Parameter
VDD1 to GND1
VDD2 to GND2
Analog Input Voltage to GND1
Digital Input Voltage to GND2
Output Voltage to GND2
Input Current to Any Pin Except Supplies1
Operating Temperature Range
AD7403
AD7403-8
Storage Temperature Range
Junction Temperature
Pb-Free Temperature, Soldering
Reflow
ESD
FICDM2
HBM3
Rating
−0.3 V to +6.5 V
−0.3 V to +6.5 V
−1 V to VDD1 + 0.3 V
−0.3 V to VDD2 + 0.5 V
−0.3 V to VDD2 + 0.3 V
±10 mA
Table 9. Maximum Continuous Working Voltage1
Parameter
AC Voltage
Bipolar Waveform
Max
Unit
Constraint
1250
VPEAK
Unipolar Waveform
1250
VPEAK
1250
VPEAK
20-year minimum
lifetime (VDE
approved working
voltage)
20-year minimum
lifetime
20-year minimum
lifetime
DC Voltage
1
−40°C to +125°C
−40°C to +105°C
−65°C to +150°C
150°C
Refers to continuous voltage magnitude imposed across the isolation
barrier.
ESD CAUTION
260°C
2 kV
±1250 V
±4000 V
Transient currents of up to 100 mA do not cause SCR to latch up.
JESD22-C101; RC network: 1 Ω, Cpkg; Class: IV.
3
ESDA/JEDEC JS-001-2011; RC network: 1.5 kΩ, 100 pF; Class: 3A.
1
2
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. B | Page 8 of 24
Data Sheet
AD7403
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
VDD1 1
16 GND2
15 NIC2
VIN+ 2
VIN– 3
AD7403
14 VDD2
GND1 4
TOP VIEW 13 MCLKIN
NIC1 5 (Not to Scale) 12 NIC2
NIC1 6
11 MDAT
VDD1 7
10 NIC2
9
GND2
1NIC = NOT INTERNALLY CONNECTED. CONNECT TO V
DD1 , GND1, OR LEAVE FLOATING.
2NIC = NOT INTERNALLY CONNECTED. CONNECT TO V
DD2 , GND2, OR LEAVE FLOATING.
12196-004
GND1 8
Figure 5. AD7403 Pin Configuration
Table 10. AD7403 Pin Function Descriptions
Mnemonic
VDD1
2
3
4, 8
5, 6
9, 16
10, 12, 15
11
VIN+
VIN−
GND1
NIC
GND2
NIC
MDAT
13
MCLKIN
14
VDD2
Description
Supply Voltage, 4.5 V to 5.5 V. This is the supply voltage for the isolated side of the AD7403 and is relative to GND1.
For device operation, connect the supply voltage to both Pin 1 and Pin 7. Decouple each supply pin to GND1 with
a 10 µF capacitor in parallel with a 1 nF capacitor.
Positive Analog Input.
Negative Analog Input. Normally connected to GND1.
Ground 1. This pin is the ground reference point for all circuitry on the isolated side.
Not Internally Connected. These pins are not internally connected. Connect to VDD1, GND1, or leave floating.
Ground 2. This pin is the ground reference point for all circuitry on the nonisolated side.
Not Internally Connected. These pins are not internally connected. Connect to VDD2, GND2, or leave floating.
Serial Data Output. The single bit modulator output is supplied to this pin as a serial data stream. The bits are
clocked out on the rising edge of the MCLKIN input and are valid on the following MCLKIN rising edge.
Master Clock Logic Input. 5 MHz to 20 MHz frequency range. The bit stream from the modulator is propagated on
the rising edge of the MCLKIN.
Supply Voltage, 3 V to 5.5 V. This is the supply voltage for the nonisolated side and is relative to GND2. Decouple
this supply to GND2 with a 100 nF capacitor.
VDD1 1
VIN+ 2
AD7403-8
8
VDD2
7
MCLKIN
TOP VIEW
6 MDAT
(Not to Scale)
5 GND2
GND1 4
VIN– 3
12196-038
Pin No.
1, 7
Figure 6. AD7403-8 Pin Configuration
Table 11. AD7403-8 Pin Function Descriptions
Pin No.
1
Mnemonic
VDD1
2
3
4
5
6
VIN+
VIN−
GND1
GND2
MDAT
7
MCLKIN
8
VDD2
Description
Supply Voltage, 4.5 V to 5.5 V. This is the supply voltage for the isolated side of the AD7403-8 and is relative to GND1.
For device operation, connect the supply voltage to both Pin 1 and Pin 7. Decouple each supply pin to GND1 with
a 10 µF capacitor in parallel with a 1 nF capacitor.
Positive Analog Input.
Negative Analog Input. Normally connected to GND1.
Ground 1. This pin is the ground reference point for all circuitry on the isolated side.
Ground 2. This pin is the ground reference point for all circuitry on the nonisolated side.
Serial Data Output. The single bit modulator output is supplied to this pin as a serial data stream. The bits are
clocked out on the rising edge of the MCLKIN input and are valid on the following MCLKIN rising edge.
Master Clock Logic Input. 5 MHz to 20 MHz frequency range. The bit stream from the modulator is propagated on
the rising edge of the MCLKIN.
Supply Voltage, 3 V to 5.5 V. This is the supply voltage for the nonisolated side and is relative to GND2. Decouple
this supply to GND2 with a 100 nF capacitor.
Rev. B | Page 9 of 24
AD7403
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VDD1 = 5 V, VDD2 = 5 V, VIN+ = −250 mV to +250 mV, VIN− = 0 V, fMCLKIN = 20 MHz, using a sinc3 filter with a 256 oversampling
ratio (OSR), unless otherwise noted.
0
90
200mV p-p SINE WAVE ON VDD1
1nF DECOUPLING
88
–20
86
84
SINAD (dB)
PSRR (dB)
–40
–60
MCLKIN = 20MHz
MCLKIN = 10MHz
–80
82
16MHz MCLKIN,
16MHz MCLKIN,
16MHz MCLKIN,
20MHz MCLKIN,
20MHz MCLKIN,
20MHz MCLKIN,
80
78
76
VDD1
VDD1
VDD1
VDD1
VDD1
VDD1
= 4.5V
= 5.0V
= 5.5V
= 4.5V
= 5.0V
= 5.5V
74
–100
1M
70
100
12196-005
800k
400k
600k
200k
SUPPLY RIPPLE FREQUENCY (Hz)
0
Figure 7. AD7403 PSRR vs. Supply Ripple Frequency
10k
Figure 10. SINAD vs. Analog Input Frequency
0
0
–20
–20
200mV p-p SINE WAVE ON VDD1
1nF DECOUPLING
fIN = 1kHz
SNR = 88.6dB
SINAD = 88.3dB
THD = –100.5dB
–40
MAGNITUDE (dB)
–40
–60
–80
MCLKIN = 20MHz
MCLKIN = 10MHz
–100
–60
–80
–100
–120
–120
–140
200k
400k
600k
800k
SUPPLY RIPPLE FREQUENCY (Hz)
0
1M
12196-042
–140
–160
0
5
10
15
20
25
30
FREQUENCY (kHz)
Figure 8. AD7403-8 PSRR vs. Supply Ripple Frequency
12196-008
PSRR (dB)
1k
ANALOG INPUT FREQUENCY (Hz)
12196-007
72
–120
Figure 11. Typical Fast Fourier Transform (FFT)
0
1.0
SHORTED INPUTS
200mV p-p SINE WAVE ON INPUTS
–20
0.8
0.6
DNL ERROR (LSB)
MCLKIN = 20MHz, SINC3 DECIMATION RATE = 256
MCLKIN = 10MHz, SINC3 DECIMATION RATE = 256
MCLKIN = 20MHz, UNFILTERED
MCLKIN = 10MHz, UNFILTERED
–60
–80
0.4
0.2
0
–0.2
–0.4
–100
–0.6
–120
1k
10k
100k
RIPPLE FREQUENCY (Hz)
1M
Figure 9. CMRR vs. Common-Mode Ripple Frequency
–1.0
0
10
20
30
40
CODE (k)
Figure 12. Typical DNL Error
Rev. B | Page 10 of 24
50
60
12196-009
–0.8
–140
100
12196-006
CMRR (dB)
–40
Data Sheet
AD7403
100
1.0
fIN = 1kHz
0.8
0.6
SNR AND SINAD (dB)
INL ERROR (LSB)
90
0.4
0.2
0
–0.2
–0.4
SNR
SINAD
80
70
–0.6
0
10
20
30
40
50
60
CODE (k)
60
–50
12196-010
–1.0
–25
0
25
50
75
100
125
150
125
150
TEMPERATURE (°C)
Figure 13. AD7403 Typical INL Error
12196-012
–0.8
Figure 16. SNR and SINAD vs. Temperature
–60
1.0
fIN = 1kHz
–70
THD AND SFDR (dB)
0
–0.5
–1.0
–80
–100
10
20
30
CODE (k)
40
50
60
–120
–50
12196-043
0
–25
0
25
50
75
100
TEMPERATURE (°C)
Figure 14. AD7403-8 Typical INL Error
12196-013
–110
–1.5
Figure 17. AD7403 THD and SFDR vs. Temperature
–60
800
692381
700
–70
THD AND SFDR (dB)
500
400
300
200
THD
SFDR
fIN = 1kHz
MCLKIN = 10MHz
VIN+ = VIN– = 0V
1M SAMPLES
600
–80
–90
–100
160941
144470
–110
100
0
0
1147
32764
32765
32766
32767
32768
1061
0
32769
32770
CODE
–120
–50
12196-011
HITS PER CODE (k)
THD
SFDR
–90
–25
0
25
50
TEMPERATURE (°C)
75
100
Figure 18. AD7403-8 THD and SFDR vs. Temperature
Figure 15. Histogram of Codes at Code Center
Rev. B | Page 11 of 24
125
12196-044
INL ERROR (LSB)
0.5
AD7403
Data Sheet
35
200
MCLKIN = 20MHz
150
30
100
25
0
20
MCLKIN = 20MHz, –40°C
MCLKIN = 20MHz, +25°C
MCLKIN = 20MHz, +85°C
MCLKIN = 20MHz, +125°C
MCLKIN = 10MHz, –40°C
MCLKIN = 10MHz, +25°C
MCLKIN = 10MHz, +85°C
MCLKIN = 10MHz, +125°C
15
–50
10
–100
5
–150
0
–25
25
50
75
100
125
150
TEMPERATURE (°C)
0
4.50
12196-014
–200
–50
5.00
4.75
5.25
5.50
VDD1 (V)
12196-016
IDD1 (mA)
OFFSET (µV)
50
Figure 22. IDD1 vs. VDD1 at Various Temperatures and Clock Rates
Figure 19. AD7403 Offset vs. Temperature
32
800
TA = –40°C
TA = 0°C
TA = +25°C
TA = +85°C
TA = +125°C
31
600
DC INPUT
30
IDD1 (mA)
OFFSET (µV)
400
200
29
28
0
27
MCLKIN = 10MHz
MCLKIN = 16MHz
MCLKIN = 20MHz
–25
0
25
50
TEMPERATURE (°C)
75
100
125
25
–250
–125
0
125
250
VIN+ DC INPUT (mV)
12196-017
–400
–50
26
12196-045
–200
Figure 23. IDD1 vs. VIN+ DC Input at Various Temperatures
Figure 20. AD7403-8 Offset vs. Temperature
10
14
MCLKIN = 10MHz
MCLKIN = 20MHz
8
12
10
IDD2 (mA)
2
0
–2
–4
8
6
MCLKIN = 20MHz, –40°C
MCLKIN = 20MHz, +25°C
MCLKIN = 20MHz, +85°C
MCLKIN = 20MHz, +125°C
MCLKIN = 10MHz, –40°C
MCLKIN = 10MHz, +25°C
MCLKIN = 10MHz, +85°C
MCLKIN = 10MHz, +125°C
4
–6
2
–8
–10
–50
–25
0
25
50
75
100
TEMPERATURE (°C)
125
150
0
3.0
3.5
4.0
4.5
5.0
5.5
VDD2 (V)
Figure 24. IDD2 vs. VDD2 at Various Temperatures and Clock Rates
Figure 21. Gain Error vs. Temperature
Rev. B | Page 12 of 24
12196-018
4
12196-015
GAIN ERROR (mV)
6
Data Sheet
AD7403
60
14
TA = –40°C
TA = 0°C
TA = +25°C
TA = +85°C
TA = +125°C
13
DC INPUT
DC INPUT
40
IIN+ (µA)
12
0
MCLKIN = 5MHz
MCLKIN = 10MHz
MCLKIN = 20MHz
–20
11
10
–250
–125
0
125
VIN+ DC INPUT (mV)
250
–60
–320
–240
–160
–80
0
80
160
240
VIN+ DC INPUT (mV)
Figure 26. IIN+ vs. VIN+ DC Input at Various Clock Rates
Figure 25. IDD2 vs. VIN+ DC Input at Various Temperatures
Rev. B | Page 13 of 24
320
12196-020
–40
12196-019
IDD2 (mA)
20
AD7403
Data Sheet
TERMINOLOGY
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the
fundamental. It is defined as
Differential Nonlinearity (DNL)
DNL is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
Integral Nonlinearity (INL)
INL is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are specified negative full
scale, −250 mV (VIN+ − VIN−), Code 7168 for the 16-bit level,
and specified positive full scale, +250 mV (VIN+ − VIN−),
Code 58,368 for the 16-bit level.
THD(dB) = 20 log
V2 2 + V3 2 + V4 2 + V5 2 + V6 2
V1
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through the sixth harmonics.
Offset Error
Offset error is the deviation of the midscale code (32,768 for the
16-bit level) from the ideal VIN+ − VIN− (that is, 0 V).
Gain Error
The gain error includes both positive full-scale gain error and
negative full-scale gain error. Positive full-scale gain error is the
deviation of the specified positive full-scale code (58,368 for the
16-bit level) from the ideal VIN+ − VIN− (250 mV) after the offset
error is adjusted out. Negative full-scale gain error is the
deviation of the specified negative full-scale code (7168 for the
16-bit level) from the ideal VIN+ − VIN− (−250 mV) after the
offset error is adjusted out.
Signal-to-Noise-and-Distortion Ratio (SINAD)
SINAD is the measured ratio of signal to noise and distortion at
the output of the ADC. The signal is the rms value of the sine
wave, and noise is the rms sum of all nonfundamental signals
up to half the sampling frequency (fS/2), including harmonics,
but excluding dc.
Signal-to-Noise Ratio (SNR)
SNR is the measured ratio of signal to noise at the output of the
ADC. The signal is the rms amplitude of the fundamental. Noise
is the sum of all nonfundamental signals up to half the sampling
frequency (fS/2), excluding dc.
The ratio is dependent on the number of quantization levels in the
digitization process: the greater the number of levels, the smaller
the quantization noise. The theoretical signal-to-noise ratio for
an ideal N-bit converter with a sine wave input is given by
Signal-to-Noise Ratio = (6.02N + 1.76) dB
Therefore, for a 12-bit converter, the SNR is 74 dB.
Isolation Transient Immunity
The isolation transient immunity specifies the rate of rise and
fall of a transient pulse applied across the isolation boundary,
beyond which clock or data is corrupted. The AD7403 was
tested using a transient pulse frequency of 100 kHz.
Peak Harmonic or Spurious Noise (SFDR)
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2, excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it is
a noise peak.
Effective Number of Bits (ENOB)
ENOB is defined by
ENOB = (SINAD − 1.76)/6.02 bits
Noise Free Code Resolution
Noise free code resolution represents the resolution in bits for
which there is no code flicker. The noise free code resolution for
an N-bit converter is defined as
Noise Free Code Resolution (Bits) = log2(2N/Peak-to-Peak Noise)
The peak-to-peak noise in LSBs is measured with VIN+ = VIN− = 0 V.
Common-Mode Rejection Ratio (CMRR)
CMRR is defined as the ratio of the power in the ADC output at
±250 mV frequency, f, to the power of a +250 mV peak-to-peak
sine wave applied to the common-mode voltage of VIN+ and VIN−
of frequency, fS, as
CMRR (dB) = 10 log(Pf/PfS)
where:
Pf is the power at frequency, f, in the ADC output.
PfS is the power at frequency, fS, in the ADC output.
Power Supply Rejection Ratio (PSRR)
Variations in power supply affect the full-scale transition but
not the linearity of the converter. PSRR is the maximum change
in the specified full-scale (±250 mV) transition point due to a
change in power supply voltage from the nominal value.
Rev. B | Page 14 of 24
Data Sheet
AD7403
THEORY OF OPERATION
A differential signal of 0 V ideally results in a stream of alternating 1s and 0s at the MDAT output pin. This output is high
50% of the time and low 50% of the time. A differential input of
250 mV produces a stream of 1s and 0s that are high 89.06% of
the time. A differential input of −250 mV produces a stream of
1s and 0s that are high 10.94% of the time.
CIRCUIT INFORMATION
The AD7403 isolated Σ-Δ modulator converts an analog input
signal into a high speed (20 MHz maximum), single-bit data
stream; the time average single-bit data from the modulator is
directly proportional to the input signal. Figure 27 shows a
typical application circuit where the AD7403 is used to provide
isolation between the analog input, a current sensing resistor or
shunt, and the digital output, which is then processed by a
digital filter to provide an N-bit word.
A differential input of 320 mV ideally results in a stream of all
1s. A differential input of −320 mV ideally results in a stream of
all 0s. The absolute full-scale range is ±320 mV and the specified
full-scale performance range is ±250 mV, as shown in Table 12.
ANALOG INPUT
Table 12. Analog Input Range
The differential analog input of the AD7403 is implemented
with a switched capacitor circuit. This circuit implements a
second-order modulator stage that digitizes the input signal
into a single-bit output stream. The sample clock (MCLKIN)
provides the clock signal for the conversion process as well as
the output data framing clock. This clock source is externally
supplied to the AD7403. The analog input signal is
continuously sampled by the modulator and compared to an
internal voltage reference. A digital stream that accurately
represents the analog input over time appears at the output of
the converter (see Figure 28).
Analog Input
Positive Full-Scale Value
Positive Specified Performance Input
Zero
Negative Specified Performance Input
Negative Full-Scale Value
Voltage Input (mV)
+320
+250
0
−250
−320
FLOATING
POWER SUPPLY
+400V
NONISOLATED
5V/3V
GATED
DRIVE
CIRCUIT
10µF 1nF
VDD1
220pF
10Ω
VIN+
10Ω
RSHUNT
FLOATING
POWER SUPPLY
220pF
VDD2
Σ-Δ
MOD/
ENCODER
MDAT
MDAT
MCLKIN
MCLK
VDD
GND1
5.1V
SINC3 FILTER*
CS
DECODER
SCLK
VIN–
10µF 1nF
VDD1
DECODER
GND2
GND1
GATED
DRIVE
CIRCUIT
SDAT
100nF
ENCODER
GND
12196-022
*THIS FILTER IS IMPLEMENTED
WITH AN FPGA OR DSP
–400V
Figure 27. Typical Application Circuit
MODULATOR OUTPUT
+FS ANALOG INPUT
–FS ANALOG INPUT
ANALOG INPUT
Figure 28. Analog Input vs. Modulator Output
Rev. B | Page 15 of 24
12196-021
MOTOR
AD7403
AD7403
Data Sheet
To reconstruct the original information, this output must be
digitally filtered and decimated. A sinc3 filter is recommended
because it is one order higher than that of the AD7403 modulator,
which is a second-order modulator. If a 256 decimation rate is
used, the resulting 16-bit word rate is 78.1 kSPS, assuming a
20 MHz external clock frequency. See the Digital Filter section
for more detailed information on the sinc filter implementation.
Figure 29 shows the transfer function of the AD7403 relative to
the 16-bit output.
DIFFERENTIAL INPUTS
The analog input to the modulator is a switched capacitor
design. The analog signal is converted into charge by highly
linear sampling capacitors. A simplified equivalent circuit
diagram of the analog input is shown in Figure 30. A signal
source driving the analog input must provide the charge onto the
sampling capacitors every half MCLKIN cycle and settle to the
required accuracy within the next half cycle.
φA
VIN+
65535
300Ω
58368
VIN–
300Ω
φB
1.9pF
φA
1.9pF
φB
MCLKIN
φA φB φA φB
12196-024
ADC CODE
SPECIFIED RANGE
Figure 30. Analog Input Equivalent Circuit
7168
Because the AD7403 samples the differential voltage across its
analog inputs, low noise performance is attained with an input
circuit that provides low common-mode noise at each input.
DIGITAL OUTPUT
–320mV
–250mV
+250mV +320mV
ANALOG INPUT
Figure 29. Filtered and Decimated 16-Bit Transfer Function
12196-023
0
The AD7403 MDAT output driver is a slew rate limited driver.
This driver lowers electromagnetic emissions, thus minimizing
electromagnetic interference (EMI), both conducted and
radiated.
Rev. B | Page 16 of 24
Data Sheet
AD7403
APPLICATIONS INFORMATION
90
CURRENT SENSING APPLICATIONS
AD7403 20MHz
AD7403-8 20MHz
The AD7403 is ideally suited for current sensing applications
where the voltage across a shunt resistor (RSHUNT) is monitored.
The load current flowing through an external shunt resistor
produces a voltage at the input terminals of the AD7403. The
AD7403 provides isolation between the analog input from the
current sensing resistor and the digital outputs. By selecting the
appropriate shunt resistor value, a variety of current ranges can
be monitored.
85
SINAD (dB)
80
75
13-BIT
ENOB
70
65
The shunt resistor (RSHUNT) values used in conjunction with the
AD7403 are determined by the specific application requirements in terms of voltage, current, and power. Small resistors
minimize power dissipation, whereas low inductance resistors
prevent any induced voltage spikes, and good tolerance devices
reduce current variations. The final values chosen are a
compromise between low power dissipation and accuracy.
Higher value resistors use the full performance input range
of the ADC, thus achieving maximum SNR performance.
Low value resistors dissipate less power but do not use the
full performance input range. The AD7403, however, delivers
excellent performance, even with lower input signal levels,
allowing low value shunt resistors to be used while maintaining
system performance.
11-BIT
ENOB
60
0
50
100
150
VIN+ (mV)
200
250
Figure 31. SINAD vs. VIN+ AC Input Signal Amplitude
1.6
DC INPUT
100k SAMPLES PER DATA POINT
1.4
RMS NOISE (LSB)
1.2
MCLKIN = 5MHz
MCLKIN = 10MHz
MCLKIN = 20MHz
1.0
0.8
0.6
0.4
To choose a suitable shunt resistor, first determine the current
through the shunt. The shunt current for a 3-phase induction
motor can be expressed as
0
–320
–240
–160
–80
0
80
160
240
320
12196-026
0.2
VIN+ DC INPUT SIGNAL AMPLITUDE (mV)
PW
1.73 × V × EF × PF
12196-046
fIN = 1kHz
MCLKIN = 20MHz
VDD1 = 5V
VDD2 = 5V
TA = 25°C
12-BIT
ENOB
Choosing RSHUNT
I RMS =
14-BIT
ENOB
Figure 32. RMS Noise vs. VIN+ DC Input Signal Amplitude
where:
IRMS is the motor phase current (A rms).
PW is the motor power (Watts).
V is the motor supply voltage (V ac).
EF is the motor efficiency (%).
PF is the power efficiency (%).
To determine the shunt peak sense current, ISENSE, consider the
motor phase current and any overload that may be possible in
the system. When the peak sense current is known, divide the
voltage range of the AD7403 (±250 mV) by the peak sense
current to yield a maximum shunt value.
If the power dissipation in the shunt resistor is too large, the
shunt resistor can be reduced and less of the ADC input range can
be used. Figure 31 shows the SINAD performance characteristics
and the ENOB of resolution for the AD7403 for different input
signal amplitudes. Figure 32 shows the rms noise performance
for dc input signal amplitudes. The performance of the AD7403
at lower input signal ranges allows smaller shunt values to be
used while still maintaining a high level of performance and
overall system efficiency.
RSHUNT must be able to dissipate the I2R power losses. If the
power dissipation rating of the resistor is exceeded, its value
may drift or the resistor may be damaged, resulting in an open
circuit. This open circuit can result in a differential voltage
across the terminals of the AD7403, in excess of the absolute
maximum ratings. If ISENSE has a large high frequency
component, choose a resistor with low inductance.
VOLTAGE SENSING APPLICATIONS
The AD7403 can also be used for isolated voltage monitoring.
For example, in motor control applications, it can be used to
sense the bus voltage. In applications where the voltage being
monitored exceeds the specified analog input range of the
AD7403, a voltage divider network can be used to reduce the
voltage being monitored to the required range.
Rev. B | Page 17 of 24
AD7403
Data Sheet
INPUT FILTER
DIGITAL FILTER
In a typical use case for directly measuring the voltage across a
shunt resistor, the AD7403 can be connected directly across the
shunt resistor with a simple RC low-pass filter on each input.
The output of the AD7403 is a continuous digital bit stream. To
reconstruct the original input signal information, this output
bit stream needs to be digitally filtered and decimated. A sinc
filter is recommended due to its simplicity. A sinc3 filter is
recommended because it is one order higher than that of the
AD7403 modulator, which is a second-order modulator. The type
of filter selected, the decimation rate, and the modulator clock used
determines the overall system resolution and throughput rate. The
higher the decimation rate, the greater the system accuracy, as
illustrated in Figure 36. However, there is a trade-off between
accuracy and throughput rate and, therefore, higher decimation
rates result in lower throughput solutions. Note that for a given
bandwidth requirement, a higher MCLKIN frequency can allow
higher decimation rates to be used, resulting in higher SNR
performance.
The recommended circuit configuration for driving the
differential inputs to achieve best performance is shown in
Figure 33. An RC low-pass filter is placed on both the analog
input pins. Recommended values for the resistors and capacitors
are 10 Ω and 220 pF, respectively. If possible, equalize the
source impedance on each analog input to minimize offset.
C
R
VIN+
AD7403
R
12196-027
VIN–
100
90
Figure 33. RC Low-Pass Filter Input Network
80
70
SNR (dB)
The input filter configuration for the AD7403 is not limited to
the low-pass structure shown in Figure 33. The differential RC
filter configuration shown in Figure 34 also achieves excellent
performance. Recommended values for the resistors and
capacitor are 22 Ω and 47 pF, respectively.
40
SINC1
SINC2
SINC3
SINC4
20
10
12196-028
R
VIN–
0
10
Figure 34. Differential RC Filter Network
100
1000
DECIMATION RATE
Figure 35 compares the typical performance for the input filter
structures outlined in Figure 33 and Figure 34 for different
resistor and capacitor values.
95
fIN = 1kHz
Figure 36. SNR vs. Decimation Rate for Different Sincx Filter Orders
A sinc3 filter is recommended for the AD7403. This filter can
be implemented on a field programmable gate array (FPGA) or
a digital signal processor (DSP).
Equation 1 describes the transfer function of a sinc filter.
90
85
 1 (1 − Z − DR ) 

H ( z ) = 
−1 
 DR (1 − Z ) 
80
SNR (dB)
50
AD7403
C
75
65
LOW PASS, 10Ω, 220pF
DIFFERENTIAL, 22Ω, 47pF
DIFFERENTIAL, 22Ω, 10nF
1000
Throughput =
12196-029
DECIMATION RATE
(1)
The throughput rate of the sinc filter is determined by the
modulator clock and the decimation rate selected.
55
100
N
where:
DR is the decimation rate.
N is the sinc filter order.
70
50
10
60
30
R
VIN+
60
fIN = 1kHz
12196-030
C
Figure 35. SNR vs. Decimation Rate for Different Filter Structures for Different
Resistor and Capacitor Values
MCLK
DR
(2)
where MCLK is the modulator clock frequency
As the decimation rate increases, the data output size from the
sinc filter increases. The output data size is expressed in
Equation 3. The 16 most significant bits are used to return a
16-bit result.
Data size = N × log2 DR
Rev. B | Page 18 of 24
(3)
Data Sheet
AD7403
Z = one sample delay MCLKOUT = modulators
conversion bit rate */
MCLKIN
Throughput
Rate (kHz)
625
312.5
156.2
78.1
39.1
Output Data
Size (Bits)
15
18
21
24
27
Filter
Response (kHz)
163.7
81.8
40.9
20.4
10.2
The following Verilog code provides an example of a sinc3 filter
implementation on a Xilinx® Spartan®-6 FPGA. Note that the
data is read on the positive clock edge. It is recommended to
read in the data on the positive clock edge. The code is
configurable to accommodate decimation rates from 32 to 4096.
module dec256sinc24b
(
input mclk1, /* used to clk filter */
input reset, /* used to reset filter */
input mdata1, /* input data to be filtered
*/
output reg [15:0] DATA, /* filtered output
*/
output reg data_en,
input [15:0] dec_rate
);
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
+
Z
ACC3+
+
always @ (negedge mclk1, posedge reset)
begin
if (reset)
begin
/* initialize acc registers on reset
*/
acc1 <= 37'd0;
acc2 <= 37'd0;
acc3 <= 37'd0;
end
else
begin
/*perform accumulation process */
acc1 <= acc1 + ip_data1;
acc2 <= acc2 + acc1;
acc3 <= acc3 + acc2;
end
end
/*decimation stage (MCLKOUT/WORD_CLK) */
always @ (posedge mclk1, posedge reset)
begin
if (reset)
word_count <= 16'd0;
else
begin
ip_data1;
acc1;
acc2;
acc3;
acc3_d2;
diff1;
diff2;
diff3;
diff1_d;
diff2_d;
if ( word_count == dec_rate - 1
)
word_count <= 16'd0;
else
word_count <= word_count
+ 16'b1;
end
end
always @ ( posedge mclk1, posedge reset )
begin
if ( reset )
word_clk <= 1'b0;
else
begin
if ( word_count == dec_rate/2 1 )
word_clk <= 1'b1;
else if ( word_count ==
dec_rate - 1 )
word_clk <= 1'b0;
end
end
reg [15:0] word_count;
reg word_clk;
reg enable;
/*Perform the Sinc
always @ (mdata1)
if(mdata1==0)
ip_data1 <=
/* change 0
complement */
else
ip_data1 <=
Z
Figure 37. Accumulator
/* Data is read on positive clk edge */
reg
reg
reg
reg
reg
reg
reg
reg
reg
reg
Z
+
Table 13. Sinc3 Filter Characteristics for 20 MHz MCLKIN
Decimation
Ratio (DR)
32
64
128
256
512
ACC2+
ACC1+
IP_DATA1
12196-031
For a sinc3 filter, the −3 dB filter response point can be derived
from the filter transfer function, Equation 1, and is 0.262 times
the throughput rate. The filter characteristics for a third-order
sinc filter are summarized in Table 13.
action*/
37'd0;
to a -1 for twos
37'd1;
/*Accumulator (Integrator)
Perform the accumulation (IIR) at the speed
of the modulator.
/*Differentiator (including decimation
stage)
Perform the differentiation stage (FIR) at a
lower speed.
Rev. B | Page 19 of 24
AD7403
Data Sheet
Z = one sample delay WORD_CLK = output word
rate */
+
ACC3
DIFF1
+
–
DIFF2
+
–
Z–1
Z–1
12196-032
Z–1
DIFF3
–
WORD_CLK
Figure 38. Differentiator
always @ (posedge word_clk, posedge reset)
begin
if(reset)
begin
acc3_d2 <= 37'd0;
diff1_d <= 37'd0;
diff2_d <= 37'd0;
diff1 <= 37'd0;
diff2 <= 37'd0;
diff3 <= 37'd0;
end
else
begin
DATA <= (diff3[24:8] ==
17'h10000) ? 16'hFFFF : diff3[23:8];
end
16'd512:begin
DATA <= (diff3[27:11] ==
17'h10000) ? 16'hFFFF : diff3[26:11];
end
16'd1024:begin
DATA <= (diff3[30:14] ==
17'h10000) ? 16'hFFFF : diff3[29:14];
end
16'd2048:begin
DATA <= (diff3[33:17] ==
17'h10000) ? 16'hFFFF : diff3[32:17];
end
16'd4096:begin
DATA <= (diff3[36:20] ==
17'h10000) ? 16'hFFFF : diff3[35:20];
end
default:begin
DATA <= (diff3[24:8] ==
17'h10000) ? 16'hFFFF : diff3[23:8];
end
endcase
end
diff1 <= acc3 - acc3_d2;
diff2 <= diff1 - diff1_d;
diff3 <= diff2 - diff2_d;
acc3_d2 <= acc3;
diff1_d <= diff1;
diff2_d <= diff2;
/* Synchronize Data Output*/
always@ ( posedge mclk1, posedge reset )
begin
if ( reset )
begin
data_en <= 1'b0;
enable <= 1'b1;
end
else
begin
if ( (word_count == dec_rate/2
- 1) && enable )
begin
data_en <= 1'b1;
enable <= 1'b0;
end
else if ( (word_count ==
dec_rate - 1) && ~enable )
begin
data_en <= 1'b0;
enable <= 1'b1;
end
else
data_en <= 1'b0;
end
end
/* Clock the Sinc output into an output
register
WORD_CLK = output word rate */
DIFF3
DATA
12196-033
WORD_CLK
Figure 39. Clocking Sinc3 Output into an Output Register
always @ ( posedge word_clk )
begin
case ( dec_rate )
16'd32:begin
DATA <= (diff3[15:0] ==
16'h8000) ? 16'hFFFF : {diff3[14:0], 1'b0};
end
16'd64:begin
DATA <= (diff3[18:2] ==
17'h10000) ? 16'hFFFF : diff3[17:2];
end
16'd128:begin
DATA <= (diff3[21:5] ==
17'h10000) ? 16'hFFFF : diff3[20:5];
end
16'd256:begin
end
end
endmodule
Rev. B | Page 20 of 24
Data Sheet
AD7403
Figure 40 shows the typical interface between the AD7403 and
the ADSP-CM4xx. Additional information on the configuration of
the sinc filter modules in the ADSP-CM4xx can be found in the
AN-1265 Application Note.
SINC PAIR n
SINC0_D0
MDAT
PRIMARY
LIMIT
SECONDARY
CONTROL FOR GROUP n
MCLKIN
AD74031
MODULATOR CLOCK n
12196-034
SINC0_CLK0
ADSP-CM4xx1
1ADDITIONAL PINS OMITTED FOR CLARITY
Figure 40. Interfacing the AD7403 to the ADSP-CM4xx
ISOLATION
BARRIER
4.5V TO 36V
ADP2441
DC-TO-DC
SWITCHING
REGULATOR
5V VDD1
VDD2 5V DIGITAL
12196-040
The ADSP-CM4xx family of mixed-signal control processors
contains on-chip sinc filter and clock generation modules for
direct connection to the AD7403 MCLKIN and MDAT pins.
The ADSP-CM4xx can process bit streams from four AD7403
devices using a pair of configurable sinc filters for each bit stream.
The primary sinc filter of each pair produces the filtered and
decimated output for the pair. The output can be decimated to
any integer rate between 8 and 256 times lower than the input
rate. The four secondary sinc filters are low latency filters with
programmable positive and negative overrange detection
comparators that can be used to detect system fault conditions
Another method is to regulate a dc supply on the high voltage
side of the isolation barrier using a step-down dc-to-dc regulator,
such as the ADP2441.
AD7403
INTERFACING TO ADSP-CM4xx
Figure 42. ADP2441 Step-Down DC-to-DC Regulator Example
GROUNDING AND LAYOUT
It is recommended to decouple the VDD1 supply with a 10 μF
capacitor in parallel with a 1 nF capacitor to GND1. Decouple
Pin 1 and Pin 7 individually. Decouple the VDD2 supply with a
100 nF value to GND2. In applications involving high commonmode transients, ensure that board coupling across the isolation
barrier is minimized. Furthermore, design the board layout so
that any coupling that occurs equally affects all pins on a given
component side. Failure to ensure equal coupling can cause
voltage differentials between pins to exceed the absolute maximum
ratings of the device, thereby leading to latch-up or permanent
damage. Place any decoupling used as close to the supply pins as
possible.
Minimize series resistance in the analog inputs to avoid any
distortion effects, especially at high temperatures. If possible,
equalize the source impedance on each analog input to minimize
offset. Check for mismatch and thermocouple effects on the analog
input printed circuit board (PCB) tracks to reduce offset drift.
POWER SUPPLY CONSIDERATIONS
INSULATION LIFETIME
The AD7403 requires a 5 V VDD1 supply, and there are various
means of achieving this. One method is to use an isolated dc-todc converter such as the ADuM6000. This method provides a 5 V
regulated dc supply across the isolation barrier. Note that the
inherent isolation of the ADuM6000 is lower than the AD7403.
All insulation structures eventually break down when subjected
to voltage stress over a sufficiently long period. The rate of
insulation degradation is dependent on the characteristics of
the voltage waveform applied across the insulation. In addition
to the testing performed by the regulatory agencies, Analog
Devices carries out an extensive set of evaluations to determine
the lifetime of the insulation structure within the AD7403.
DC-TO-DC
CONVERTER
5V DIGITAL
VDD2
12196-039
VDD1
AD7403
5V ISO
ADuM6000
ISOLATION
BARRIER
Analog Devices performs accelerated life testing using voltage
levels higher than the rated continuous working voltage.
Acceleration factors for several operating conditions are
determined. These factors allow calculation of the time to
failure at the actual working voltage. The values shown in Table 9
summarize the peak voltage for 20 years of service life for a
bipolar, ac operating condition and the maximum VDE
approved working voltages.
Figure 41. ADuM6000 Isolated 5 V DC-to-DC Regulator Example
Rev. B | Page 21 of 24
AD7403
Data Sheet
•
The value that ensures at least a 20-year lifetime of
continuous use.
The maximum VDE approved working voltage.
12196-035
RATED PEAK VOLTAGE
0V
Figure 43. Bipolar AC Waveform, 50 Hz or 60 Hz
RATED PEAK VOLTAGE
0V
Figure 44. Unipolar AC Waveform, 50 Hz or 60 Hz
Note that the lifetime of the AD7403 varies according to the
waveform type imposed across the isolation barrier. The
iCoupler insulation structure is stressed differently, depending
on whether the waveform is bipolar ac, unipolar ac, or dc.
RATED PEAK VOLTAGE
12196-037
•
Figure 43, Figure 44, and Figure 45 illustrate the different
isolation voltage waveforms.
12196-036
These tests subjected the AD7403 to continuous cross isolation
voltages. To accelerate the occurrence of failures, the selected
test voltages were values exceeding those of normal use. The
time to failure values of these units were recorded and used to
calculate the acceleration factors. These factors were then used
to calculate the time to failure under the normal operating
conditions. The values shown in Table 9 are the lesser of the
following two values:
0V
Figure 45. DC Waveform
Rev. B | Page 22 of 24
Data Sheet
AD7403
OUTLINE DIMENSIONS
12.85
12.75
12.65
1.93 REF
16
9
7.60
7.50
7.40
1
10.51
10.31
10.11
8
PIN 1
MARK
2.44
2.24
45°
0.32
0.23
SEATING
PLANE
1.27 BSC
8°
0°
1.01
0.76
0.51
0.46
0.36
11-15-2011-A
0.30
0.20
0.10
COPLANARITY
0.1
0.71
0.50
0.31
0.25 BSC
GAGE
PLANE
2.64
2.54
2.44
COMPLIANT TO JEDEC STANDARDS MS-013-AC
Figure 46. 16-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
Wide Body
(RI-16-2)
Dimensions shown in millimeters
6.05
5.85
5.65
8
5
7.60
7.50
7.40
1
10.51
10.31
10.11
4
2.45
2.35
2.25
0.30
0.20
0.10
COPLANARITY
0.10
2.65
2.50
2.35
1.27 BSC
0.51
0.41
0.31
SEATING
PLANE
0.75
0.50
0.25
1.04
BSC
0.75
0.58
0.40
45°
8°
0°
0.33
0.27
0.20
Figure 47. 8-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
Wide Body
(RI-8-1)
Dimensions shown in millimeters
Rev. B | Page 23 of 24
09-17-2014-B
PIN 1
MARK
AD7403
Data Sheet
ORDERING GUIDE
Model1
AD7403-8BRIZ
AD7403-8BRIZ-RL
AD7403-8BRIZ-RL7
AD7403BRIZ
AD7403BRIZ-RL
AD7403BRIZ-RL7
EVAL-AD7403-8FMCZ
EVAL-AD7403FMCZ
EVAL-SDP-CH1Z
1
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
8-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
8-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
8-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
16-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
16-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
16-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
AD7403-8 Evaluation Board
AD7403 Evaluation Board
System Demonstration Platform
Z = RoHS Compliant Part.
©2014–2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12196-0-5/15(B)
Rev. B | Page 24 of 24
Package
Option
RI-8-1
RI-8-1
RI-8-1
RI-16-2
RI-16-2
RI-16-2