!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 p/PLp Chip Ferrite Bead DL 150 Part Numbering 152 Series Line Up 154 Product Detail 156 !Caution/Notice 174 Soldering and Mounting 176 Packaging 182 Design Kits 184 Block Type EMIFILr Chip Common Mode Choke Coil Series Introduction Chip EMIFILr Chip Common Mode Choke Coil Large Current Common Mode Choke Coil for Automotive Available !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 Chip Ferrite Bead DLp Series Introduction Common Mode Current Magnetic flux by common mode current is added each other and works as an inductor Differential Mode Current Chip EMIFILr Magnetic flux by differential mode current is canceled each other and do not works as an inductor Features, Classification Category Ultra high cut-off frequency for high speed differential signal lines Structure Film type Block Type EMIFILr Chip Common Mode Choke Coil Wound type High cut-off frequency High Coupling For high speed differential signal lines ( ) High cut-off frequency for high speed differential signal lines Film type Wound type for general differential signal lines Film type Part Number Comments DLP11SA · Low profile, small size, suitable for mobile equipments. · Tight terminal pitch enables high density layout. · Ultra high cut-off frequency and its matching to line impedance enables good transmission of high speed signal. DLW21SN_HQ2 · Ultra high self resonance frequency enables high cut-off frequency. · Its matching to line impedance enables good transmission of high speed signal. DLP0NS DLP11SN DLP2AD · Low profile, small size, suitable for mobile equipments. · Tight terminal pitch enables high density layout. · High cut-off frequency enables good transmission of high speed signal. DLW21SN_SQ2 DLW31S DLW21H · Ultra high self resonance frequency enables high cut-off frequency. · DLW21H is designed as low profile. DLP31S DLP31D · Low profile,small size, suitable for mobile equipments. · Tight terminal pitch enables high density layout. DLW5AH Large current High coupling (For power lines) Wound type DLW5BS · Large current (6A max.), suitable for input connector from an AC adaptor. · DLW5BT is designed as low profile. DLW5BT Relative high differential mode impedance Low coupling (For audio lines) Large current Automotive Available (For power lines) Multilayer type Available up to 10A Winding type Cased structure DLM11G DLM2HG PLT10HH · Modified its differential mode impedance higher than other common mode choke coils, this feature makes possible to suppress both common mode and differential mode noise. · DLM11GN601SD2 is ideal to keep low distortion audio signal. · DLM2HG can meet stereo 3 lines which contain a ground line. · Large current, high reliability, suitable for mortors in automobile. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 150 Noise Suppression DLP/DLW Series Example Chip Ferrite Bead Mechanism of Skew Improvement Skew Improve Effect of Common Mode Choke Coil Waveform rises (or falls) Example of Skew Improvement by Common Mode Choke Coil (Test using pulse generator waveform) Waveform is equivalent to 1000Mbps signal Current change generates magnetic flux on a ferrite core Waveform with intentionally made skew (skew: 100ps) Skew is improved by common mode choke coil Electromotive force is generated on another line Chip EMIFILr This electromotive force works to decrease the delay of waveform Noise Suppression of Common Mode Choke Coil in HDMI Line 60 60 55 55 50 45 40 35 30 Without filter DLW21SN900HQ2 25 20 1000 1500 2000 2500 3000 3500 4000 4500 50 45 40 35 30 Without filter DLP11SA900HL2 25 20 1000 5000 1500 2000 Frequency (MHz) Test Example of HDMI1.3 Waveform Transmission Chip Common Mode Choke Coil Noise Level (dBµV/m) Noise Level (dBµV/m) Device under test / Transmitter : game machine Receiver : projector Cable / HDMI categoly2 3m cable Test resolution / 1080p Deep color 12bit (Data 1.11GHz) DVD play mode 2500 3000 3500 4000 4500 5000 Frequency (MHz) ESD protection device only Film Type DLP11SN900HL2 (Cut-off frequency is most low in the table below) ~Using ESD protection device 0.05pF~ Block Type EMIFILr Signal frequency : 1.11GHz (Deep color 12bit) Specification satisfied Video signal generator CLOCK Wound Type DLW21SN900HQ2 Film Type DLP11SA900HL2 Film Type Array DLP2ADN900HL4 Over 10GHz Around 6GHz Around 4GHz Specification satisfied Specification satisfied Specification satisfied Rise time: 83.4ps Fall time: 77.4ps Rise time: 90.4ps Fall time: 85.5ps Rise time: 100ps Fall time: 97.4ps DATA common mode choke coil ESD protection device 0.05pF Cut-off Frequency Judge Transition Time Each of common mode choke coil can keep waveform, satisfy the specification. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 151 Chip Ferrite Bead DL p (Part Number) Chip Common Mode Choke Coil DL W 21 S N q w e r t 371 S Q 2 Part Numbering L u i o !0 y qProduct ID tCategory Product ID Code DL Chip Common Mode Choke Coils Category A B Chip EMIFILr wStructure C Code Structure N W Wire Wound Type R M Multilayer Type P Film Type eDimensions (LgW) Code Dimensions (LgW) EIA 0N 0.85g0.65mm 03025 Expressed by a letter. yImpedance Typical impedance at 100MHz is expressed by three figures. The unit is in ohm (Ω). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two figures. uCircuit 11 1.25g1.0mm 0504 1N 1.5g0.65mm 05025 Code 21 2.0g1.2mm 0805 S 31 3.2g1.6mm 1206 M 2A 2.0g1.0mm 0804 H 2H 2.5g2.0mm 1008 U 5A 5.0g3.6mm 2014 5B 5.0g5.0mm 2020 Circuit Expressed by a letter. iFeatures (2) Chip Common Mode Choke Coil Code rFeatures (1) Features D Code Type L S Magnetically Shielded One Circuit Type Q D Magnetically Shielded Two Circuit Type Z H Open Magnetic One Circuit Type G Magnetically Monolithic Type (sectional winding) T Magnetically Shielded One Circuit Low Profile Type Expressed by a letter. oNumber of Signal Lines Code Number of Signal Lines 2 Two Lines 3 Three Lines 4 Four Lines Block Type EMIFILr !0Packaging Code Packaging K Embossed Taping (ø330mm Reel) DLW5AH/DLW5BS/DLW5BT Series L Embossed Taping (ø180mm Reel) All Series B Bulk All Series !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 152 Part Numbering T 10H H 102 6R0 P N B PL q w e r t y u i o qProduct ID Product ID PL Common Mode Choke Coils Code Type T DC Type wType eApplications Code Applications 10H for DC Line High-frequency Type rFeatures Code Features H for Automotive tImpedance Expressed by three figures. The unit is ohm (Ω). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two figures. yRated Current Expressed by three figures. The unit is ampere (A). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two figures. A decimal point is expressed by the capital letter "R". In this case, all figures are significant digits. Chip EMIFILr (Part Number) Common Mode Choke Coils Chip Ferrite Bead PL p uWinding Mode Code Winding Mode P Aligned Winding Type iLead Dimensions Code Lead Dimensions N No Lead Terminal (SMD) oPackaging Bulk PLT10H Series L Embossed Taping (ø178mm/ø180mm Reel) PLT10H K Embossed Taping (ø330mm Reel) PLT10H Chip Common Mode Choke Coil Packaging B Block Type EMIFILr Code !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 153 DL p Chip Common Mode Choke Coil Type Chip Ferrite Bead Multilayer Type for Audio Lines Size Code Thickness (Inch) (mm) 0504 1008 p158 p159 p160 03025 p162 Chip EMIFILr Film Type for Differential Signal Lines 0504 p163 p164 1206 p165 05025 p166 Chip Common Mode Choke Coil Film Array Type for Differential Signal Lines 0804 p168 1206 p169 Block Type EMIFILr 0805 Wire Wound Type for Differential Signal Lines p171 p172 1206 0.5 1.2 0.45 0.45 0.45 0.45 0.45 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.3 1.15 1.15 1.15 0.45 0.45 0.45 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 1.15 1.15 1.15 1.15 1.15 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 0.9 0.9 0.9 0.9 1.9 1.9 1.9 1.9 1.9 1.9 Part Number DLM11GN601SD2 DLM2HGN601SZ3 DLP0NSN670HL2 DLP0NSN900HL2 DLP0NSN121HL2 DLP0NSA150HL2 DLP0NSC280HL2 DLP11SN670SL2 DLP11SN121SL2 DLP11SN161SL2 DLP11SN900HL2 DLP11SN201HL2 DLP11SN241HL2 DLP11SN281HL2 DLP11SN331HL2 DLP11SA350HL2 DLP11SA670HL2 DLP11SA900HL2 DLP11TB800UL2 DLP31SN121ML2 DLP31SN221ML2 DLP31SN551ML2 DLP1NDN350HL4 DLP1NDN670HL4 DLP1NDN900HL4 DLP2ADA350HL4 DLP2ADA670HL4 DLP2ADA900HL4 DLP2ADN670HL4 DLP2ADN900HL4 DLP2ADN121HL4 DLP2ADN161HL4 DLP2ADN201HL4 DLP2ADN241HL4 DLP2ADN281HL4 DLP31DN900ML4 DLP31DN131ML4 DLP31DN201ML4 DLP31DN321ML4 DLP31DN441ML4 DLW21SN670SQ2 DLW21SN900SQ2 DLW21SN121SQ2 DLW21SN181SQ2 DLW21SN261SQ2 DLW21SN371SQ2 DLW21SN670HQ2 DLW21SN900HQ2 DLW21SN121HQ2 DLW21SR670HQ2 DLW21HN670SQ2 DLW21HN900SQ2 DLW21HN121SQ2 DLW21HN181SQ2 DLW31SN900SQ2 DLW31SN161SQ2 DLW31SN261SQ2 DLW31SN601SQ2 DLW31SN102SQ2 DLW31SN222SQ2 Series Line Up Common Mode Impedance Rated Current (at 100MHz/20°C) 600ohm±25% 600ohm±25% 67ohm±20% 90ohm±20% 120ohm±20% 15ohm±5ohm 28ohm±20% 67ohm±20% 120ohm±20% 160ohm±20% 90ohm±20% 200ohm±20% 240ohm±20% 280ohm±20% 330ohm±20% 35ohm±20% 67ohm±20% 90ohm±20% 80ohm±25% 120ohm±20% 220ohm±20% 550ohm±20% 35ohm±20% 67ohm±20% 90ohm±20% 35ohm±20% 67ohm±20% 90ohm±20% 67ohm±20% 90ohm±20% 120ohm±20% 160ohm±20% 200ohm±20% 240ohm±20% 280ohm±20% 90ohm±20% 130ohm±20% 200ohm±20% 320ohm±20% 440ohm±20% 67ohm±25% 90ohm±25% 120ohm±25% 180ohm±25% 260ohm±25% 370ohm±25% 67ohm±25% 90ohm±25% 120ohm±25% 67ohm±25% 67ohm±25% 90ohm±25% 120ohm±25% 180ohm±25% 90ohm±25% 160ohm±25% 260ohm±25% 600ohm±25% 1000ohm±25% 2200ohm±25% 100mA 100mA 110mA 100mA 90mA 100mA 100mA 180mA 140mA 120mA 150mA 110mA 100mA 90mA 80mA 170mA 150mA 150mA 100mA 100mA 100mA 100mA 100mA 80mA 60mA 150mA 130mA 120mA 140mA 130mA 120mA 100mA 90mA 80mA 80mA 160mA 120mA 100mA 80mA 70mA 400mA 330mA 370mA 330mA 300mA 280mA 320mA 280mA 280mA 400mA 330mA 330mA 280mA 250mA 370mA 340mA 310mA 260mA 230mA 200mA Continued on the following page. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 154 DLp Chip Common Mode Choke Coil Series Line Up p156 p156 Wire Wound Type for Power Lines and Signal Lines PL p 2020p157 4.3 4.5 4.5 4.5 4.5 4.5 2.5 2.5 2.5 2.5 2.5 DLW5AHN402SQ2 DLW5BSN191SQ2 DLW5BSN351SQ2 DLW5BSN102SQ2 DLW5BSN152SQ2 DLW5BSN302SQ2 DLW5BTN101SQ2 DLW5BTN251SQ2 DLW5BTN501SQ2 DLW5BTN102SQ2 DLW5BTN142SQ2 Common Mode Impedance Rated Current (at 100MHz/20°C) 4000ohm(Typ.) 190ohm(Typ.) 350ohm(Typ.) 1000ohm(Typ.) 1500ohm(Typ.) 3000ohm(Typ.) 100ohm(Typ.) 250ohm(Typ.) 500ohm(Typ.) 1000ohm(Typ.) 1400ohm(Typ.) 200mA 5000mA 2000mA 1500mA 1000mA 500mA 6000mA 5000mA 4000mA 2000mA 1500mA Large Current Common Mode Choke Coil for Automotive Available Type Size p173 12.9x6.6 (mm) Part Number 9.4 9.4 9.4 9.4 PLT10HH401100PN PLT10HH501100PN PLT10HH9016R0PN PLT10HH1026R0PN Series Line Up Common Mode Impedance Rated Current (at 10MHz/20°C) 400ohm 500ohm 900ohm 1000ohm 10A 10A 6A 6A Block Type EMIFILr Chip Common Mode Choke Coil Large Current Common Mode Choke Coil for Automotive Available Thickness (mm) Chip Ferrite Bead 2014 Part Number Chip EMIFILr Size Code Thickness (Inch) (mm) Type !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 155 DLW Series Universal Type [Power Lines/Signal Lines] Chip Common Mode Choke Coil DLW5AH/DLW5BS DLW5AH/DLW5BS Series (2014/2020 Size) ■ Equivalent Circuit 0.45 min. ■ Dimensions DLW5AH * * 0.5 min. (W) 3.6±0.3 (1) No polarity. 1.7 1.3 1.7 ±0.3 ±0.3 ±0.3 Chip EMIFILr ■ Packaging position of wiring should * Starting be covered with resin. : Electrode (3) 1.3 0.9 1.3 ±0.3 ±0.3 ±0.3 (in mm) ■ Dimensions DLW5BS (3) (4) (L) 5.0±0.3 (2) (4) (2) (1) (T) 4.3 max. Chip Ferrite Bead 5A max, common mode choke coil for power lines. Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 400 K 330mm Reel Embossed Tape 1500 B Bulk(Bag) 100 ■ Equivalent Circuit Polarity Marking * The marking to indicate the product direction can be applicable. (Optional) (2) (1) (3) (4) 1.7±0.3 Chip Common Mode Choke Coil Universal Type [Power Lines/Signal Lines] (4) ■ Packaging (T) 4.5 max. 0.5 min. (L) 5.0±0.3 1.3±0.3 1.7±0.3 3.6±0.3 (W) 5.0±0.3 (1) (2) 0.45 min. No polarity. : Electrode (3) 1.3±0.3 0.9±0.3 (in mm) Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 400 K 330mm Reel Embossed Tape 1500 B Bulk(Bag) 100 Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Insulation Resistance (min.) Part Number Common Mode Impedance (at 100MHz/20°C) DLW5AHN402SQ2p 4000ohm(Typ.) 200mA 50Vdc 10M ohm 125Vdc 3.0ohm max. DLW5BSN191SQ2p 190ohm(Typ.) 5000mA 50Vdc 10M ohm 125Vdc 0.02ohm max. DLW5BSN351SQ2p 350ohm(Typ.) 2000mA 50Vdc 10M ohm 125Vdc 0.04ohm max. DLW5BSN102SQ2p 1000ohm(Typ.) 1500mA 50Vdc 10M ohm 125Vdc 0.06ohm max. DLW5BSN152SQ2p 1500ohm(Typ.) 1000mA 50Vdc 10M ohm 125Vdc 0.1ohm max. DLW5BSN302SQ2p 3000ohm(Typ.) 500mA 50Vdc 10M ohm 125Vdc 0.3ohm max. Rated Current Rated Voltage Withstand Voltage DC Resistance ■ Impedance-Frequency Characteristics (Main Items) 100000 ■ Derating of Rated Current DLW5BSN191 DLW5BSN191SQ2 Temperature Derating 10000 5 DLW5AHN402SQ2 DLW5BSN302SQ2 DLW5BSN152SQ2 DLW5BSN102SQ2 DLW5BSN351SQ2 DLW5BSN191SQ2 1000 Rated Current (A) Impedance (Ω) Block Type EMIFILr Operating Temperature Range: -25°C to +85°C (DLW5AH), -40°C to +85°C (DLW5BS) Number of Circuit: 1 Common mode 100 DLW5AHN402SQ2 DLW5BSN302SQ2 DLW5BSN152SQ2 Differential mode 4.75 4.5 DLW5BSN102SQ2 DLW5BSN351SQ2 DLW5BSN191SQ2 10 1 10 100 Frequency (MHz) 1000 0 10 20 30 40 50 60 Operating Temperature (°C) 70 80 75°C 90 100 85°C !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 156 DLW Series Universal Type [Power Lines/Signal Lines] Chip Common Mode Choke Coil DLW5BT DLW5BT Series (2020 Size) ■ Dimensions Chip Ferrite Bead Low profile wire-wound common choke coil for power lines. ■ Equivalent Circuit * The marking to indicate the product direction can be applicable. (Optional) Polarity Marking (2) (1) (3) (4) (4) (2) (3) 1.3±0.3 (1) 0.45 min. 0.5 min. (L) 5.0±0.3 ■ Packaging : Electrode 1.3±0.3 0.9±0.3 Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 700 K 330mm Reel Embossed Tape 2500 B Bulk(Bag) 100 (in mm) Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Insulation Resistance (min.) Part Number Common Mode Impedance (at 100MHz/20°C) DLW5BTN101SQ2p 100ohm(Typ.) 6000mA 50Vdc 10M ohm 125Vdc 0.009ohm±40% DLW5BTN251SQ2p 250ohm(Typ.) 5000mA 50Vdc 10M ohm 125Vdc 0.014ohm±40% DLW5BTN501SQ2p 500ohm(Typ.) 4000mA 50Vdc 10M ohm 125Vdc 0.019ohm±40% DLW5BTN102SQ2p 1000ohm(Typ.) 2000mA 50Vdc 10M ohm 125Vdc 0.024ohm±40% DLW5BTN142SQ2p 1400ohm(Typ.) 1500mA 50Vdc 10M ohm 125Vdc 0.040ohm±40% Rated Current Rated Voltage Withstand Voltage DC Resistance Chip EMIFILr 1.7±0.3 1.7±0.3 3.6±0.3 (W) 5.0±0.3 (T) 2.35±0.15 No polarity. Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 ■ Impedance-Frequency Characteristics (Main Items) 10000 ■ Derating of Rated Current DLW5BTN101/251/501 Common mode DLW5BTN102SQ2 1000 6000 DLW5BTN101SQ2 Current (mA) Impedance (Ω) DLW5BTN501SQ2 DLW5BTN251SQ2 100 Universal Type [Power Lines/Signal Lines] Chip Common Mode Choke Coil 7000 DLW5BTN142SQ2 5000 4750 4000 3400 3000 10 DLW5BTN101SQ2 DLW5BTN251SQ2 DLW5BTN501SQ2 DLW5BTN102SQ2 DLW5BTN142SQ2 Differential mode 1 1 10 100 Frequency (MHz) 1000 2000 1000 0 0 20 40 60 80 65 100 85 Block Type EMIFILr Temperature (°C) !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 157 DLM Series Signal Lines Type Chip Common Mode Choke Coil DLM11G DLM11G Series (0504 Size) Chip Ferrite Bead Audio line common choke also effective to differential mode. ■ Equivalent Circuit (1) (2) (4) (3) 0.2±0.15 No polarity. ■ Packaging : Electrode (in mm) Chip EMIFILr (3) (4) 0.5±0.1 1.0±0.15 (2) (1) 0.65±0.1 1.25±0.15 0.35±0.15 ■ Dimensions Code Packaging Minimum Quantity D 180mm Reel Paper Tape 10000 B Bulk(Bag) 1000 Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Common Mode Impedance Rated Current Rated Voltage (at 100MHz/20°C) Part Number DLM11GN601SD2p 600ohm±25% 100mA 5Vdc Insulation Resistance (min.) Withstand Voltage DC Resistance 100M ohm 25Vdc 0.8ohm max. Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 ■ Impedance-Frequency Characteristics (Main Items) 10000 DLM11GN601SD2 Differential Mode Impedance (Ω) 100 Common Mode DLM11GN601SD2 10 1 1 10 100 1000 Frequency (MHz) Block Type EMIFILr Chip Common Mode Choke Coil Signal Lines Type 1000 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 158 DLM Series Signal Lines Type Chip Common Mode Choke Coil DLM2HG DLM2HG Series (1008 Size) (3) (5) (4) (6) 0.3±0.2 (2) ■ Equivalent Circuit 2.0±0.2 (3) (5) (2) (4) (6) No polarity. ■ Packaging 1.2±0.2 0.4±0.2 (1) : Electrode (in mm) 0.8±0.1 Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 1000 Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) DLM2HGN601SZ3p 600ohm±25% 100mA 16Vdc 100M ohm Withstand Voltage DC Resistance 100Vdc Chip EMIFILr (1) 2.5±0.2 ■ Dimensions Chip Ferrite Bead 3 line audio common mode choke coil. 0.40ohm max. Operating Temperature Range: -55°C to +85°C Number of Circuit: 1 ■ Impedance-Frequency Characteristics (Main Items) 10000 100 DLM2HGN601SZ3 Signal Lines Type Chip Common Mode Choke Coil Impedance (Ω) Differential Mode DLM2HGN601SZ3 1000 Common Mode 10 1 10 100 Frequency (MHz) 1000 10000 Block Type EMIFILr 1 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 159 DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP0NS DLP0NS Series (03025 Size) Chip Ferrite Bead 03025 size, very small chip common mode choke coil, Cut-off frequency 3GHz max. ■ Dimensions ■ Equivalent Circuit 0.27±0.1 (2) 0.45±0.05 (1) (3) (4) 0.5±0.1 (2) (3) (4) 0.85±0.05 No polarity. (1) ■ Packaging 0.20+0.05 –0.10 Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 5000 B Bulk(Bag) 500 0.65±0.05 : Electrode Chip EMIFILr (in mm) Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLP0NSN670HL2p 67ohm±20% 110mA 5Vdc 100M ohm 12.5Vdc 2.4ohm±25% DLP0NSN900HL2p 90ohm±20% 100mA 5Vdc 100M ohm 12.5Vdc 3.0ohm±25% DLP0NSN121HL2p 120ohm±20% 90mA 5Vdc 100M ohm 12.5Vdc 3.8ohm±25% DLP0NSA150HL2p 15ohm±5ohm 100mA 5Vdc 100M ohm 12.5Vdc 0.95ohm±25% DLP0NSC280HL2p 28ohm±20% 100mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% HD: for high speed differential signal lines Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 UD: for ultra high speed differential signal lines ■ Impedance-Frequency Characteristics (Main Items) DLP0NSA150HL2/DLP0NSC280HL2 10000 10000 Common Mode DLP0NSN121HL2 1000 1000 DLP0NSN670HL2 100 DLP0NSN121HL2 10 Impedance (Ω) DLP0NSN900HL2 Impedance (Ω) Chip Common Mode Choke Coil Signal Lines Type DLP0NSN 670/900/121 HL2 Common Mode DLP0NSC280HL2 100 DLP0NSA150HL2 10 DLP0NSN900HL2 DLP0NSC280HL2 DLP0NSA150HL2 DLP0NSN670HL2 Differential Mode Differential Mode 1 1 1 10 100 Frequency (MHz) 1000 10000 1 10 100 Frequency (MHz) 1000 10000 DLP0NSN900HL2 DLP0NSA150HL2 0 0 2 2 DLP0NSN900HL2 DLP0NSA150HL2 Insertion Loss (dB) Insertion Loss (dB) Block Type EMIFILr ■ Differential Mode Transmission Characteristics (Typ.) 4 6 8 4 6 8 10 10 1 10 100 Frequency (MHz) 1000 10000 1 10 100 Frequency (MHz) 1000 10000 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 160 DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP0NS Series (03025 Size) DLP0NS Chip Ferrite Bead ■ Differential Mode Transmission Characteristics (Typ.) DLP0NSC280HL2 0 2 Insertion Loss (dB) DLP0NSC280HL2 4 6 8 10 10 100 Frequency (MHz) 1000 10000 Block Type EMIFILr Signal Lines Type Chip Common Mode Choke Coil Chip EMIFILr 1 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 161 DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP11S/DLP11T DLP11S/11T Series (0504 Size) Chip Ferrite Bead 6GHz cut-off frequency (for HDMI) is available. ■ Dimensions ■ Equivalent Circuit 0.3±0.1 (2) T (1) (3) (4) No polarity. (1) 1.0±0.1 0.55±0.1 (2) Part Number T DLP11S 0.82±0.1 DLP11T 0.3±0.05 (3) (4) ■ Packaging Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 (DLP11S) 5000 (DLP11T) B Bulk(Bag) 500 0.25+0.1 –0.05 : Electrode 1.25±0.1 Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLP11SN670SL2p 67ohm±20% 180mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% DLP11SN121SL2p 120ohm±20% 140mA 5Vdc 100M ohm 12.5Vdc 2.0ohm±25% DLP11SN161SL2p 160ohm±20% 120mA 5Vdc 100M ohm 12.5Vdc 2.7ohm±25% DLP11SN900HL2p 90ohm±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.5ohm±25% DLP11SN201HL2p 200ohm±20% 110mA 5Vdc 100M ohm 12.5Vdc 3.1ohm±25% DLP11SN241HL2p 240ohm±20% 100mA 5Vdc 100M ohm 12.5Vdc 3.5ohm±25% DLP11SN281HL2p 280ohm±20% 90mA 5Vdc 100M ohm 12.5Vdc 4.2ohm±25% DLP11SN331HL2p 330ohm±20% 80mA 5Vdc 100M ohm 12.5Vdc 4.9ohm±25% DLP11SA350HL2p 35ohm±20% 170mA 5Vdc 100M ohm 12.5Vdc 0.9ohm±25% DLP11SA670HL2p 67ohm±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.2ohm±25% DLP11SA900HL2p 90ohm±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.4ohm±25% UD: for ultra high speed differential signal lines ■ Impedance-Frequency Characteristics DLP11SN Series DLP11SA Series 1000 10000 Common mode DLP11SN331HL2 DLP11SN281HL2 Impedance (Ω) 1000 Block Type EMIFILr HD: for high speed differential signal lines Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 DLP11SN241HL2 DLP11SN201HL2 DLP11SN161SL2 DLP11SN121SL2 DLP11SN900HL2 DLP11SN670SL2 100 10 1 1 10 Common mode 100 DLP11SN331HL2 DLP11SN281HL2 DLP11SN241HL2 DLP11SN201HL2 DLP11SN161SL2 DLP11SN121SL2 DLP11SN900HL2 DLP11SN670SL2 Differential mode 100 Frequency (MHz) 1000 10000 Impedance (Ω) Chip Common Mode Choke Coil Signal Lines Type Chip EMIFILr (in mm) DLP11SA900HL2 DLP11SA670HL2 DLP11SA350HL2 10 DLP11SA900HL2 DLP11SA670HL2 DLP11SA350HL2 Differential mode 1 1 10 100 Frequency (MHz) 1000 10000 Continued on the following page. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 162 DLP11S/11T DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP11S/11T Series (0504 Size) DLP11SN Series Chip Ferrite Bead ■ Differential Mode Transmission Characteristics (Typ.) DLP11SA Series 0 0 DLP11SA900HL2 2 2 Insertion Loss (dB) 4 6 8 4 6 8 10 10 1 10 100 Frequency (MHz) 1000 10000 1 10 100 Frequency (MHz) 1000 10000 Chip EMIFILr Insertion Loss (dB) DLP11SN900HL2 ■ Rated Value (p: packaging code) Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage DLP11TB800UL2p 80ohm±25% 100mA 5Vdc DLP11TB Series Withstand Voltage 100M ohm 12.5Vdc HD: for high speed differential signal lines Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 Differential mode to common mode conversion characteristic (Scd21) at 2.5GHz: -40dB (typ.) Impedance Characteristics between signal lines Z0 (TDR at 50ps): 90ohm±15ohm ■ Impedance-Frequency Characteristics Insulation Resistance (min.) DC Resistance 1.5ohm±25% UD: for ultra high speed differential signal lines ■ Differential Mode Transmission Characteristics DLP11TB Series 1000 0 Common Mode DLP11TB800UL2 Impedance (Ω) DLP11TB800UL2 DLP11TB800UL2 10 Signal Lines Type Chip Common Mode Choke Coil 100 Insertion Loss (dB) 2 4 6 8 Differential Mode 1 10 10 100 Frequency (MHz) 1000 10000 1 10 100 Frequency (MHz) 1000 10000 Block Type EMIFILr 1 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 163 DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP31S DLP31S Series (1206 Size) Chip Ferrite Bead 1206 size film type chip common mode choke coil. ■ Dimensions ■ Equivalent Circuit 0.7±0.2 (2) 1.15±0.15 (1) (2.1) 1.6±0.15 (3) (4) 3.2±0.15 (1) No polarity. (2) ■ Packaging (4) Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 500 (3) : Electrode 0.3±0.2 Chip EMIFILr (in mm) Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Insulation Resistance (min.) Part Number Common Mode Impedance (at 100MHz/20°C) DLP31SN121ML2p 120ohm±20% 100mA 16Vdc 100M ohm 40Vdc 2.0ohm max. DLP31SN221ML2p 220ohm±20% 100mA 16Vdc 100M ohm 40Vdc 2.5ohm max. DLP31SN551ML2p 550ohm±20% 100mA 16Vdc 100M ohm 40Vdc Rated Current Rated Voltage Withstand Voltage DC Resistance HD: for high speed differential signal lines Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 3.6ohm max. UD: for ultra high speed differential signal lines ■ Impedance-Frequency Characteristics (Main Items) 10000 1000 Impedance (Ω) 100 Common mode 10 DLP31SN121ML2 DLP31SN221ML2 DLP31SN551ML2 Differential mode 1 1 10 100 1000 Frequency (MHz) Block Type EMIFILr Chip Common Mode Choke Coil Signal Lines Type DLP31SN551ML2 DLP31SN221ML2 DLP31SN121ML2 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 164 DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP1ND DLP1ND Series (0502 Size) ■ Dimensions ■ Equivalent Circuit (1) (2) (3) (4) (5) (6) (7) No polarity. (8) (3) (4) (5) (6) (7) (8) ■ Packaging 1.5±0.1 Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 5000 B Bulk(Bag) 500 : Electrode (in mm) Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Common Mode Impedance Rated Current Rated Voltage (at 100MHz/20°C) Part Number DLP1NDN350HL4p 35ohm±20% 100mA 5Vdc 100M ohm 12.5Vdc 1.8ohm±25% DLP1NDN670HL4p 67ohm±20% 80mA 5Vdc 100M ohm 12.5Vdc 2.9ohm±25% DLP1NDN900HL4p 90ohm±20% 60mA 5Vdc 100M ohm 12.5Vdc Operating Temperature Range: -40°C to +85°C Number of Circuit: 2 HD: for high speed differential signal lines ■ Impedance-Frequency Characteristics 3.7ohm±25% UD: for ultra high speed differential signal lines ■ Differential Mode Transmission Characteristics 0 10000 Common mode -2 DLP1NDN900HL4 Insertion Loss (dB) DLP1NDN900HL4 DLP1NDN670HL4 DLP1NDN350HL4 100 Signal Lines Type Chip Common Mode Choke Coil 1000 Impedance (Ω) Insulation Resistance Withstand Voltage DC Resistance (min.) Chip EMIFILr (2) 0.1 min. (1) 0.45±0.05 0.4±0.1 0.65±0.1 0.2±0.1 0.2±0.1 Chip Ferrite Bead 2 circuits in 05025 size, adapt to HDMI line. -4 -6 DLP1NDN350HL4 10 DLP1NDN670HL4 -8 DLP1NDN900HL4 Differential mode -10 1 10 100 Frequency (MHz) 1000 10000 10 100 1000 10000 Frequency (MHz) Block Type EMIFILr 1 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 165 DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP2AD DLP2AD Series (0804 Size) Chip Ferrite Bead 2 circuit built-in, 0804 size, HDMI adapted type available, cut-off frequency 6GHz max. ■ Dimensions ■ Equivalent Circuit 0.5±0.1 (2) (3) (4) (5) (6) (7) (8) 1.0±0.1 0.25±0.15 (1) (3) (4) (5) (6) (7) No polarity. (8) Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 500 : Electrode (in mm) Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLP2ADA350HL4p 35ohm±20% 150mA 5Vdc 100M ohm 12.5Vdc 0.8ohm±25% DLP2ADA670HL4p 67ohm±20% 130mA 5Vdc 100M ohm 12.5Vdc 1.0ohm±25% DLP2ADA900HL4p 90ohm±20% 120mA 5Vdc 100M ohm 12.5Vdc 1.4ohm±25% DLP2ADN670HL4p 67ohm±20% 140mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% DLP2ADN900HL4p 90ohm±20% 130mA 5Vdc 100M ohm 12.5Vdc 1.7ohm±25% DLP2ADN121HL4p 120ohm±20% 120mA 5Vdc 100M ohm 12.5Vdc 2.0ohm±25% DLP2ADN161HL4p 160ohm±20% 100mA 5Vdc 100M ohm 12.5Vdc 2.5ohm±25% DLP2ADN201HL4p 200ohm±20% 90mA 5Vdc 100M ohm 12.5Vdc 3.2ohm±25% DLP2ADN241HL4p 240ohm±20% 80mA 5Vdc 100M ohm 12.5Vdc 3.8ohm±25% DLP2ADN281HL4p 280ohm±20% 80mA 5Vdc 100M ohm 12.5Vdc Operating Temperature Range: -40°C to +85°C Number of Circuit: 2 HD: for high speed differential signal lines 4.6ohm±25% UD: for ultra high speed differential signal lines ■ Impedance-Frequency Characteristics (Main Items) DLP2ADA Series DLP2ADN Series 10000 1000 Common Mode Common mode DLP2ADN281HL4 DLP2ADN241HL4 DLP2ADN201HL4 DLP2ADN161HL4 DLP2ADN121HL4 DLP2ADN900HL4 DLP2ADN670HL4 DLP2ADA900HL4 1000 Impedance (Ω) DLP2ADA670HL4 100 DLP2ADA350HL4 DLP2ADA900HL4 Impedance (Ω) Chip EMIFILr (2) ■ Packaging 2.0±0.1 Chip Common Mode Choke Coil Signal Lines Type (1) 0.82±0.1 0.25±0.1 100 10 10 Block Type EMIFILr DLP2ADA670HL4 DLP2ADA350HL4 Differential Mode 1 1 10 100 Frequency (MHz) 1000 10000 DLP2ADN670HL4 1 1 10 DLP2ADN281HL4 DLP2ADN241HL4 DLP2ADN201HL4 DLP2ADN161HL4 DLP2ADN121HL4 Differential mode DLP2ADN900HL4 100 Frequency (MHz) 1000 10000 Continued on the following page. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 166 DLP2AD DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP2AD Series (0504 Size) DLP2ADA Series Chip Ferrite Bead ■ Differential Mode Transmission Characteristics (Typ.) DLP2ADN Series 0 0 2 2 DLP2ADA900HL4 Insertion Loss (dB) Insertion Loss (dB) DLP2ADN900HL4 DLP2ADA670HL4 4 DLP2ADA350HL4 6 4 6 8 8 10 10 10 100 1000 10000 1 10 100 Frequency (MHz) 1000 10000 Block Type EMIFILr Signal Lines Type Chip Common Mode Choke Coil Chip EMIFILr Frequency (MHz) !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 167 DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP31D DLP31D Series (1206 Size) Chip Ferrite Bead 2 circuit built-in, 1206 size, meet IEEE1394,USB,LVDS. ■ Equivalent Circuit (2) (3) (4) (2) (3) (4) (5) (6) (7) No polarity. (8) ■ Packaging 1.6±0.15 (1) 0.8±0.1 0.3±0.2 0.4±0.2 (5) (6) (7) Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 500 (8) : Electrode 3.2±0.15 (in mm) Chip EMIFILr (1) 1.15±0.15 ■ Dimensions Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Insulation Resistance (min.) Part Number Common Mode Impedance (at 100MHz/20°C) DLP31DN900ML4p 90ohm±20% 160mA 10Vdc 100M ohm 25Vdc 1.1ohm max. DLP31DN131ML4p 130ohm±20% 120mA 10Vdc 100M ohm 25Vdc 1.1ohm max. DLP31DN201ML4p 200ohm±20% 100mA 10Vdc 100M ohm 25Vdc 2.2ohm max. DLP31DN321ML4p 320ohm±20% 80mA 10Vdc 100M ohm 25Vdc 3.5ohm max. DLP31DN441ML4p 440ohm±20% 70mA 10Vdc 100M ohm 25Vdc Rated Current Rated Voltage Operating Temperature Range: -40°C to +85°C Number of Circuit: 2 Withstand Voltage DC Resistance HD: for high speed differential signal lines 4.3ohm max. UD: for ultra high speed differential signal lines ■ Impedance-Frequency Characteristics (Main Items) 10000 DLP31DN441ML4 DLP31DN321ML4 DLP31DN201ML4 DLP31DN131ML4 DLP31DN900ML4 1000 Impedance (Ω) Chip Common Mode Choke Coil Signal Lines Type Common mode 100 DLP31DN441ML4 DLP31DN321ML4 10 DLP31DN900ML4 DLP31DN131ML4 DLP31DN201ML4 Differential mode 1 1 10 100 1000 Block Type EMIFILr Frequency (MHz) !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 168 DLW Series Signal Lines Type Chip Common Mode Choke Coil DLW21S DLW21S Series (0805 Size) ■ Dimensions ■ Equivalent Circuit (2) (0.17) 1.2±0.2 (1) 2.0±0.2 (3) (4) 1.2±0.2 No polarity. (0.45) (0.45) Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 2000 B Bulk(Bag) 500 : Electrode (in mm) Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLW21SN670SQ2p 67ohm±25% 400mA 50Vdc 10M ohm 125Vdc 0.25ohm max. DLW21SN900SQ2p 90ohm±25% 330mA 50Vdc 10M ohm 125Vdc 0.35ohm max. DLW21SN121SQ2p 120ohm±25% 370mA 50Vdc 10M ohm 125Vdc 0.45ohm max. DLW21SN181SQ2p 180ohm±25% 330mA 50Vdc 10M ohm 125Vdc 0.35ohm max. DLW21SN261SQ2p 260ohm±25% 300mA 50Vdc 10M ohm 125Vdc 0.40ohm max. DLW21SN371SQ2p 370ohm±25% 280mA 50Vdc 10M ohm 125Vdc 0.45ohm max. DLW21SN670HQ2p 67ohm±25% 320mA 20Vdc 10M ohm 50Vdc 0.31ohm max. DLW21SN900HQ2p 90ohm±25% 280mA 20Vdc 10M ohm 50Vdc 0.41ohm max. DLW21SN121HQ2p 120ohm±25% 280mA 20Vdc 10M ohm 50Vdc 0.41ohm max. DLW21SR670HQ2p 67ohm±25% 400mA 20Vdc 10M ohm 50Vdc Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 HD: for high speed differential signal lines 0.25ohm max. UD: for ultra high speed differential signal lines DLW21SR670HQ2 is designed to correct line impedance when ESD protection device is also used. ■ Impedance-Frequency Characteristics (Main Items) DLW21SN_SQ2 Series DLW21SN_HQ2 Series 1000 Impedance (Ω) 1000 Common mode Common mode 100 Impedance (Ω) DLW21SN371SQ2 DLW21SN261SQ2 DLW21SN181SQ2 DLW21SN121SQ2 DLW21SN900SQ2 DLW21SN670SQ2 100 10 1 Differential mode 0.1 1 DLW21SN371SQ2 DLW21SN261SQ2 DLW21SN181SQ2 DLW21SN121SQ2 DLW21SN900SQ2 DLW21SN670SQ2 10 100 Frequency (MHz) 1000 DLW21SN121HQ2 DLW21SN900HQ2 DLW21SN670HQ2 10 1 DLW21SN121HQ2 Block Type EMIFILr 10000 Chip EMIFILr (3) ■ Packaging Signal Lines Type Chip Common Mode Choke Coil (4) (0.4) (2) (0.4) (1) Chip Ferrite Bead Wire-wound common choke, HDMI available type prepaird. DLW21SN900HQ2 DLW21SN670HQ2 Differential mode 0.1 10 100 Frequency (MHz) 1000 Continued on the following page. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 169 DLW Series Signal Lines Type Chip Common Mode Choke Coil DLW21S Series (0805 Size) DLW21S DLW21SR_HQ2 Series 1000 Common mode 100 DLW21SR670HQ2 Impedance (Ω) Chip Ferrite Bead ■ Impedance-Frequency Characteristics (Main Items) 10 Differential mode 1 DLW21SR670HQ2 0.1 1 10 100 1000 Chip EMIFILr Frequency (MHz) ■ Differential Mode Transmission Characteristics (Typ.) DLW21SN_HQ2 Series 0 DLW21SN900HQ2 Insertion Loss (dB) 2 4 6 8 10 10 100 Frequency (MHz) 1000 10000 Block Type EMIFILr Chip Common Mode Choke Coil Signal Lines Type 1 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 170 DLW Series Signal Lines Type Chip Common Mode Choke Coil DLW21H DLW21H Series (0805 Size) ■ Dimensions Chip Ferrite Bead Low profile wire-wound common choke coil. ■ Equivalent Circuit (2) (0.17) 0.9±0.1 (1) 2.0±0.2 1.2±0.2 (3) (4) No polarity. (2) ■ Packaging (0.4) (4) Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 500 : Electrode (3) (in mm) Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Insulation Resistance (min.) Part Number Common Mode Impedance (at 100MHz/20°C) DLW21HN670SQ2p 67ohm±25% 330mA 50Vdc 10M ohm 125Vdc 0.35ohm max. DLW21HN900SQ2p 90ohm±25% 330mA 50Vdc 10M ohm 125Vdc 0.35ohm max. DLW21HN121SQ2p 120ohm±25% 280mA 50Vdc 10M ohm 125Vdc 0.45ohm max. DLW21HN181SQ2p 180ohm±25% 250mA 50Vdc 10M ohm 125Vdc Rated Current Rated Voltage Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 Withstand Voltage DC Resistance HD: for high speed differential signal lines Chip EMIFILr (0.45) (1) (0.4) (0.45) 0.50ohm max. UD: for ultra high speed differential signal lines ■ Impedance-Frequency Characteristics (Main Items) 10000 DLW21HN181SQ2 Common mode 1000 Signal Lines Type Chip Common Mode Choke Coil Impedance (Ω) DLW21HN121SQ2 DLW21HN900SQ2 100 DLW21HN670SQ2 10 DLW21HN181SQ2 DLW21HN121SQ2 1 DLW21HN900SQ2 Differential mode DLW21HN670SQ2 0.1 1 10 100 1000 Block Type EMIFILr Frequency (MHz) !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 171 DLW Series Signal Lines Type Chip Common Mode Choke Coil DLW31S DLW31S Series (1206 Size) Chip Ferrite Bead 1206 size wire-wound common mode choke coil. ■ Dimensions ■ Equivalent Circuit (2) (0.25) 1.9±0.2 (1) 3.2±0.2 (3) (4) 1.6±0.2 No polarity. (4) ■ Packaging Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 2000 B Bulk(Bag) 500 (3) : Electrode (0.6) (0.6) Chip EMIFILr (0.6) (2) (0.6) (1) (in mm) Refer to pages from p.176 to p.179 for mounting information. ■ Rated Value (p: packaging code) Insulation Resistance (min.) Part Number Common Mode Impedance (at 100MHz/20°C) DLW31SN900SQ2p 90ohm±25% 370mA 50Vdc 10M ohm 125Vdc 0.3ohm max. DLW31SN161SQ2p 160ohm±25% 340mA 50Vdc 10M ohm 125Vdc 0.4ohm max. DLW31SN261SQ2p 260ohm±25% 310mA 50Vdc 10M ohm 125Vdc 0.5ohm max. DLW31SN601SQ2p 600ohm±25% 260mA 50Vdc 10M ohm 125Vdc 0.8ohm max. DLW31SN102SQ2p 1000ohm±25% 230mA 50Vdc 10M ohm 125Vdc 1.0ohm max. DLW31SN222SQ2p 2200ohm±25% 200mA 50Vdc 10M ohm 125Vdc Rated Current Rated Voltage Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 Withstand Voltage DC Resistance HD: for high speed differential signal lines 1.2ohm max. UD: for ultra high speed differential signal lines 10000 DLW31SN222SQ2 DLW31SN102SQ2 DLW31SN601SQ2 DLW31SN261SQ2 DLW31SN161SQ2 DLW31SN900SQ2 Common mode 1000 Impedance (Ω) Chip Common Mode Choke Coil Signal Lines Type ■ Impedance-Frequency Characteristics 100 10 DLW31SN222SQ2 DLW31SN102SQ2 DLW31SN601SQ2 DLW31SN261SQ2 DLW31SN161SQ2 DLW31SN900SQ2 Differential mode 1 0.1 1 10 100 1000 Block Type EMIFILr Frequency (MHz) !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 172 PLT Series Power Lines Type Large Current Common Mode Choke Coil for Automotive Available PLT10H PLT10H Series (12.9x6.6 mm) ■ Dimensions Chip Ferrite Bead Automotive available, up to 10A. ■ Equivalent Circuit (1) (2) (2) (1) 102 (4) (3) 6.6±0.2 12.9±0.2 (3) (4) Code Packaging Minimum Quantity 9.1±0.2 : Electrode 1.0±0.2 L 180mm Reel Embossed Tape 125 K 330mm Reel Embossed Tape 500 B Bulk(Bag) 50 (in mm) 3.2±0.3 Refer to pages from p.180 to p.181 for mounting information. ■ Rated Value (p: packaging code) Part Number Common Mode Impedance (at 10MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance Common Mode Inductance PLT10HH401100PNp 400ohm 10A 100Vdc 10M ohm 250Vdc 3.6m ohm±0.5m ohm 6µH min. PLT10HH501100PNp 500ohm 10A 100Vdc 10M ohm 250Vdc 3.6m ohm±0.5m ohm 9µH min. PLT10HH9016R0PNp 900ohm 6A 100Vdc 10M ohm 250Vdc 8.0m ohm±0.5m ohm 14µH min. PLT10HH1026R0PNp 1000ohm 6A 100Vdc 10M ohm 250Vdc 8.0m ohm±0.5m ohm 20µH min. Chip EMIFILr 1.0±0.2 ■ Packaging 2.1±0.3 2.1±0.3 13.4 max. 9.4 max. 2.0±0.3 No polarity. Operating Temperature Range (Self-temperature rise is included): -55°C to +105°C (PLT10HH 1026R0/501100 PN), -55°C to +105°C (PLT10HH 401100/9016R0 PN) Number of Circuit: 1 ■ Impedance-Frequency Characteristics Imredance (Ω) 1000 Derating PLT10HH501100PN 12 PLT10HH401100PN 10 100 Frequency (MHz) 1000 Current [A] 10 PLT10HH401 8 10 1 Power Lines Type Chip Common Mode Choke Coil PLT10HH1026R0PN PLT10HH9016R0PN 100 ■ Notice (Rating) In operating temperature exceeding +65°C, derating of current is necessary for PLT10H Series. Please apply the derating curve shown in chart according to the operating temperature. 10000 PLT10HH501 PLT10HH901 6 4 2 PLT10HH102 0 0 20 40 60 80 100 120 140 Block Type EMIFILr Operating Temperature [°C] !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 173 Chip Common Mode Choke Coil !Caution/Notice Chip Ferrite Bead !Caution ● Rating Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. ● Soldering and Mounting 2. Mounting Direction Mount Chip Common Mode Choke Coils in right direction. Wrong direction, which is 90 degrees rotated from right direction, causes not only open or short circuit but also flames or other serious trouble. Z right direction Z wrong direction Notice ● Storage and Operating Conditions ● Handling <Operating Environment> Do not use products in a chemical atmosphere such as chlorine gas, acid or sulfide gas. Do not use products in the environment close to the organic solvent. <Storage and Handling Requirements> 1. Storage Period DLW11G/DLM2HG series should be used within 6 months, the other series should be used within 12 months. Solderability should be checked if this period is exceeded. 2. Storage Conditions (1) Storage temperature: -10 to +40˚C Relative humidity: 15 to 85% Avoid sudden changes in temperature and humidity. (2) Do not store products in a chemical atmosphere such as chlorine gas, acid or sulfide gas. 1. Resin Coating (Except DLW Series.) Using resin for coating/molding products may affect the products performance. So please pay careful attention in selecting resin. Prior to use, please make the reliability evaluation with the product mounted in your application set. 2. Resin Coating (DLW Series) The impedance value may change due to high curestress of resin to be used for coating/molding products. An open circuit issue may occur by mechanical stress caused by the resin, amount/cured shape of resin, or operating condition etc. Some resin contains some impurities or chloride possible to generate chlorine by hydrolysis under some operating condition may cause corrosion of wire of coil, leading to open circuit. So, please pay your careful attention in selecting resin in case of coating/molding the products with the resin. Prior to use the coating resin, please make sure no reliability issue is observed by evaluating products mounted on your board. 3. Caution for Use (DLW Series) When you hold products with a tweezer, please hold by the sides. Sharp materials, such as a pair of tweezers, should not touch the winding portion to prevent breaking the wire. Mechanical shock should not be applied to the products mounted on the board to prevent breaking the core. 4. Brushing When you clean the neighborhood of products such as connector pins, bristles of cleaning brush shall not be touched to the winding portion of this product to prevent the breaking of wire. 5. Handling of a Substrate After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate. Excessive mechanical stress may cause cracking in the Product. ● Notice (Soldering and Mounting) 1. Cleaning Failure and degradation of a product are caused by the cleaning method. When you clean in conditions that are not in mounting information, please contact Murata engineering. 2. Soldering Reliability decreases with improper soldering methods. Please solder by the standard soldering conditions shown in mounting information. 3. Other Noise suppression levels resulting from Murata's EMI suppression filters EMIFILr may vary, depending on the circuits and ICs used, type of noise, mounting pattern, mounting location, and other operating conditions. Be sure to check and confirm in advance the noise suppression effect of each filter, in actual circuits, etc. before applying the filter in a commercialpurpose equipment design. Block Type EMIFILr !Caution/ Chip Common Mode Choke Coil Notice Chip EMIFILr 1. Self-heating Please provide special attention when mounting chip common mode choke coils DLW5 series in close proximity to other products that radiate heat. The heat generated by other products may deteriorate the insulation resistance and cause excessive heat in this component. Bending Twisting !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 174 Chip Common Mode Choke Coil !Caution/Notice ● Rating 1. Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. 2. Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure our product. Chip Ferrite Bead !Caution 2. Mounting Direction Mount Chip Common Mode Choke Coils in right direction. Wrong direction, which is 90 degrees rotated from right direction, causes not only open or short circuit but also flames or other serious trouble. Z Z ● Soldering and Mounting 1. Self-heating Please provide special attention when mounting chip common mode choke coils in close proximity to other products that radiate heat. The heat generated by other products may deteriorate the insulation resistance and cause excessive heat in this component. wrong direction Chip EMIFILr right direction ● Storage and Operating Conditions ● Notice (Soldering and Mounting) <Operating Environment> Do not use products in a chemical atmosphere such as chlorine gas, acid or sulfide gas. Do not use products in the environment close to the organic solvent. <Storage and Handling Requirements> 1. Storage Period PLT10H series should be used within 12 months. Solderability should be checked if this period is exceeded. 2. Storage Conditions (1) Storage temperature: -10 to +40˚C Relative humidity: 15 to 85% Avoid sudden changes in temperature and humidity. (2) Do not store products in a chemical atmosphere such as chlorine gas, acid or sulfide gas. 1. Cleaning Failure and degradation of a product are caused by the cleaning method. When you clean in conditions that are not in mounting information, please contact Murata engineering. 2. Soldering Reliability decreases with improper soldering methods. Please solder by the standard soldering conditions shown in mounting information. 3. Other Noise suppression levels resulting from Murata's EMI suppression filters EMIFILr may vary, depending on the circuits and ICs used, type of noise, mounting pattern, mounting location, and other operating conditions. Be sure to check and confirm in advance the noise suppression effect of each filter, in actual circuits, etc. before applying the filter in a commercialpurpose equipment design. !Caution/ Chip Common Mode Choke Coil Notice Notice ● Handling Bending Block Type EMIFILr 1. Handling of a Substrate After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate. Excessive mechanical stress may cause cracking in the Product. Twisting !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 175 DL p Soldering and Mounting Chip Common Mode Choke Coil Chip EMIFILr Land Pattern + Solder Resist Land Pattern Solder Resist (in mm) oReflow and Flow DLM2HG DLP31D DLP31S 0.7 0.8 2.2-2.6 0.7 2.8 2.1 DLM11G DLM2HG DLP0NS DLP11S DLP11T DLP1ND DLP2AD DLP31S DLP31D DLW21S DLW21H DLW31SN DLW5AH DLW5B 2.0 1.2 0.4 Chip Ferrite Bead 1. Standard Land Pattern Dimensions 1.0 4.0 1.0 0.6 1.0 0.8 Pitch 0.4 oReflow Soldering DLP0NS DLP11S DLP11T DLP1ND 1.4 0.2 0.85 1.55 DLM11G 0.4 ∗2 DLW21S/21H/31SN d 1.5 0.4 Soldering Chip Common Mode Choke Coil and Mounting 1.1 0.3 ∗1 c 1.75 0.25 0.5 1.5 ∗3 a b 0.5 Series 4.7 3.3 1.3 DLW5AH/5B Block Type EMIFILr 0.3 0.55 1.95 DLP2AD 0.9 0.3 0.85 0.3 0.55 0.90 0.55 0.3 0.55 0.80 0.50 0.3 0.30 0.9 2.9 5.5 o PCB Warping PCB should be designed so that products are not subjected to the mechanical stress caused by warping the board. a b c d DLW21S/H 0.8 2.6 0.4 1.2 DLW31SN 1.6 3.7 0.4 1.6 ∗1: If the pattern is made with wider than 1.2mm (DLW21) / 1.6mm (DLW31S) it may result in components turning around, because melting speed is different. In the worst case, short circuit between lines may occur. ∗2: If the pattern is made with less than 0.4mm, in the worst case, short circuit between lines may occur due to spread of soldering paste or mount placing accuracy. ∗3: If the pattern is made with wider than 0.8mm (DLW21) / 1.6mm (DLW31SN), the bending strength will be reduced. Do not use gild pattern; excess soldering heat may dissolve metal of a copper wire. Products should be located in the sideways direction (Length: a<b) to the mechanical stress. a b Poor example Good example !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 176 DLp Chip Common Mode Choke Coil Soldering and Mounting 2. Solder Paste Printing and Adhesive Application Chip Ferrite Bead When flow soldering the chip common mode choke coils, apply the adhesive in accordance with the following conditions. If too much adhesive is applied, then it may overflow into the land or termination areas and yield poor solderability. In contrast, if insufficient adhesive is applied, or if the adhesive is not sufficiently hardened, then the chip may become detached during flow soldering process. When reflow soldering the chip common mode choke coils, the printing must be conducted in accordance with the following cream solder printing conditions. If too much solder is applied, the chip will be prone to damage by mechanical and thermal stress from the PCB and may crack. Standard land dimensions should be used for resist and copper foil patterns. (in mm) DLP DLW DLM Solder Paste Printing Adhesive Application oGuideline of solder paste thickness: 100-150µm: DLW21S/21H/31S, DLP0NS/11S/11T/1ND/2AD/DLM11G 150-200µm: DLP31D/31S, DLM2HG, DLW5AH/5BS/5BT *Solderability is subject to reflow conditions and thermal conductivity. Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. DLP31D DLP31S Coating Position of Bonding Agent DLW21S/21H/31S d c c DLP0NS/11S/11T/31S/DLM11G DLP31S/DLM2HG/DLP31D Apply 0.3mg of bonding agent at each chip. Chip EMIFILr Series Coating Position of Bonding Agent d DLM2HG c a b Series b a a b Coating Position of Bonding Agent c d DLP0NS 0.3 0.3 0.3 0.5 DLP11S 0.7 0.55 0.3 0.55 DLP11T 0.5 0.55 0.3 0.55 DLP31S 1.0 0.6 0.7 2.1 Series a b c d Soldering and Mounting Chip Common Mode Choke Coil a DLW21S/H 0.8 2.6 0.5 1.2 DLW31S 1.6 3.7 0.4 1.6 DLM11G 0.5 0.5 0.4 0.7 DLP2AD/31D c a b c d a Series b DLP2AD 0.55 0.4 0.25 0.5 a DLP1ND 0.3 0.3 0.2 0.4 DLP31D 1.0 0.8 0.4 0.8 d 3.3 4.7 1.3 2.0 1.2 0.4 5.5 2.9 0.9 Block Type EMIFILr DLM2HG DLW5AH/5BS/5BT 1.0 4.0 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 177 DLp Chip Common Mode Choke Coil Soldering and Mounting Chip Ferrite Bead 3. Standard Soldering Conditions Flux: o Use Rosin-based flux. In case of DLW21/31 series, use Rosin-based flux with converting chlorine content of 0.06 to 0.1wt%. In case of using RA type solder, products should be cleaned completely with no residual flux. o Do not use strong acidic flux (with chlorine content exceeding 0.20wt%) o Do not use water-soluble flux. (1) Soldering Methods Use flow and reflow soldering methods only. Use standard soldering conditions when soldering chip common mode choke coils. In cases where several different parts are soldered, each having different soldering conditions, use those conditions requiring the least heat and minimum time. Solder: Use Sn-3.0Ag-0.5Cu solder. Use of Sn-Zn based solder will deteriorate performance of products. If using DLP/DLM series with Sn-Zn based solder, please contact Murata in advance. For additional mounting methods, please contact Murata. oFlow Soldering Profile (Sn-3.0Ag-0.5Cu Solder) Temperature (°C) Chip EMIFILr (2) Soldering Profile T3 T2 t2 Heating T1 Standard Profile Pre-heating t1 Standard Profile Heating Temp. (T1) Time. (t1) Temp. (T2) Time. (t2) 150°C 60s min. 250°C 4 to 6s Limit Profile Cycle of Flow Heating Temp. (T3) Time. (t2) 265±3°C 5s max. 2 times max. Cycle of Flow 2 times max. oReflow Soldering Profile (Sn-3.0Ag-0.5Cu Solder) Temperature (°C) T4 T2 T1 T3 180 150 Limit Profile Pre-heating t1 Standard Profile t2 90s±30s Block Type EMIFILr Soldering Chip Common Mode Choke Coil and Mounting DLM2HG DLP31D/31S Time (s) Pre-heating Series Limit Profile time (s) Standard Profile Series Limit Profile Temp. (T3) Peak Cycle Temperature of Reflow (T4) Time. (t2) 245±3°C 2 times max. 230°C min. 60s max. 260°C/10s 2 times max. 250±3°C 2 times max. 230°C min. 60s max. 260°C/10s 2 times max. Peak Cycle Temperature of Reflow (T2) Time. (t1) Heating Temp. (T1) DLM/DLP DLW21/31 220°C min. 30 to 60s DLW5A/5B 220°C min. 30 to 60s Heating !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 178 Soldering and Mounting (3) Reworking with Solder Iron The following conditions must be strictly followed when using a soldering iron. Pre-heating: 150°C 60s min. Soldering iron power output / Tip diameter: 30W max. / ø3mm max. Temperature of soldering iron tip / Soldering time / Times: 350°C max. / 3-4s / 2 times*1 1 * DLP0NS, DLP11S, DLP11T, DLP1ND, DLP2AD: 380°C max. / 3-4s / 2 times Do not allow the tip of the soldering iron to directly contact the chip. For additional methods of reworking with a soldering iron, please contact Murata engineering. Chip Ferrite Bead DLp Chip Common Mode Choke Coil 4. Cleaning Chip EMIFILr Before cleaning, please contact Murata engineering. (a) Alcohol cleaning agent Isopropyl alcohol (IPA) (b) Aqueous cleaning agent Pine Alpha ST-100S (4) Ensure that flux residue is completely removed. Component should be thoroughly dried after aqueous agent has been removed with deionized water. Block Type EMIFILr Soldering and Mounting Chip Common Mode Choke Coil Following conditions should be observed when cleaning chip EMI filter. (1) Cleaning Temperature: 60°C max. (40°C max. for alcohol type cleaner) (2) Ultrasonic Output: 20W/liter max. Duration: 5 minutes max. Frequency: 28 to 40kHz (3) Cleaning agent The following list of cleaning agents have been tested on the individual components. Evaluation of final assembly should be completed prior to production. Do not clean DLW (except DLW21H) series. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 179 PL p Chip Common Mode Choke Coil Soldering and Mounting (in mm) PLT10H Copper Foil Pattern Copper Foil Pattern + Resist Resist oReflow Soldering PLT10H 2.0 2.5 2.0 Chip Ferrite Bead 1. Standard Land Pattern Dimensions 4.0 8.0 4.0 Chip EMIFILr o PCB Warping PCB should be designed so that products are not subjected to the mechanical stress caused by warping the board. Products should be located in the sideways direction (Length: a<b) to the mechanical stress. a b Poor example Good example When reflow soldering the chip common mode choke coils, the printing must be conducted in accordance with the following cream solder printing conditions. If too much solder is applied, the chip will be prone to damage by mechanical and thermal stress from the PCB and may crack. Standard land dimensions should be used for resist and copper foil patterns. Series PLT10H When flow soldering the chip common mode choke coils, apply the adhesive in accordance with the following conditions. If too much adhesive is applied, then it may overflow into the land or termination areas and yield poor solderability. In contrast, if insufficient adhesive is applied, or if the adhesive is not sufficiently hardened, then the chip may become detached during flow soldering process. Solder Paste Printing oGuideline of solder paste thickness: 150-200µm: PLT10H For the solder paste printing pattern, use standard land dimensions. *Solderability is subject to reflow conditions and thermal conductivity. Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. Block Type EMIFILr Soldering Chip Common Mode Choke Coil and Mounting 2. Solder Paste Printing and Adhesive Application !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 180 PLp Chip Common Mode Choke Coil Soldering and Mounting 3. Standard Soldering Conditions (1) Soldering Methods Use reflow soldering methods only. Use standard soldering conditions when soldering chip common mode choke coils. In cases where several different parts are soldered, each having different soldering conditions, use those conditions requiring the least heat and minimum time. Chip Ferrite Bead Solder: Use Sn-3.0Ag-0.5Cu solder. Use of Sn-Zn based solder will deteriorate performance of products. Flux: o Use Rosin-based flux. use Rosin-based flux. o Do not use strong acidic flux (with chlorine content exceeding 0.20wt%) o Do not use water-soluble flux. For additional mounting methods, please contact Murata. (2) Soldering Profile Chip EMIFILr oReflow Soldering Profile (Sn-3.0Ag-0.5Cu Solder) Temperature (°C) T4 T2 T1 T3 180 150 Limit Profile Pre-heating t1 Standard Profile t2 time (s) Standard Profile Series Temp. (T1) PLT10H Limit Profile Peak Cycle Temperature of Reflow (T2) Time. (t1) Heating 220°C min. 30 to 60s 250±3°C (3) Reworking with Solder Iron The following conditions must be strictly followed when using a soldering iron. Pre-heating: 150°C 60s min. Soldering iron power output / Tip diameter: 80W max. / ø3mm max. Temperature of soldering iron tip / Soldering time / Times: 400°C max. / 5s / 2 times 2 times max. Heating Temp. (T3) Time. (t2) 230°C min. 60s max. Peak Cycle Temperature of Reflow (T4) 260°C/10s 2 times max. Soldering and Mounting Chip Common Mode Choke Coil 90s±30s Do not allow the tip of the soldering iron to directly contact the chip. For additional methods of reworking with a soldering iron, please contact Murata engineering. Block Type EMIFILr 4. Cleaning Do not clean after soldering. If cleaning, please contact us. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 181 DL p Packaging Chip Common Mode Choke Coil Minimum Quantity and Dimensions of 8mm Width Paper / Embossed Tape <Paper> 1.75±0.1 <Embossed> c d 3.5±0.05 8.0 a Chip Ferrite Bead 2.0±0.05 ∗1 4.0±0.1 4.0±0.1 ø1.5 +0.1 -0 c Direction of Feed b c: Depth of Cavity (Embossed Tape) ∗1 DLM11G: 2.0±0.05 c: Total Thickness of Tape (Paper Tape) Dimension of the cavity of embossed tape is measured at the bottom side. Part Number a Chip EMIFILr Minimum Qty. (pcs.) Cavity Size b c ø330mm Reel ø180mm Reel d Paper Tape Embossed Tape Paper Tape Embossed Tape Bulk DLM11G 1.45 1.2 0.8 max. - 10000 - - - 1000 DLM2HG 2.75 2.25 1.3 0.25 - 3000 - - 1000 DLP0NS 0.95 0.75 0.55 0.25 - 5000 - - 500 DLP11S 1.4 1.2 0.98 0.25 - 3000 - - 500 DLP11T 1.35 1.1 0.45 0.25 - 5000 - - 500 DLP1ND 1.7 0.84 0.57 0.25 - 5000 - - 500 DLP2AD 2.2 1.2 0.98 0.25 - 3000 - - 500 DLP31D/31S 3.5 1.9 1.3 0.25 - 3000 - - 500 DLW21S 2.25 1.45 1.4 0.3 - 2000 - - 500 DLW21H 2.3 1.55 1.1 0.25 - 3000 - - 500 DLW31S 3.6 2.0 2.1 0.3 - 2000 - - 500 b c 0.4 Part Number 12.0 ø1.5 +0.1 -0 5.5±0.05 a 2.0±0.05 8.0±0.1 4.0±0.1 1.75±0.1 Minimum Quantity and Dimensions of 12mm Width Embossed Tape Packaging Chip Common Mode Choke Coil (in mm) Cavity Size Minimum Qty. (pcs.) ø180mm Reel ø330mm Reel Bulk a b c DLW5AH 5.4 4.1 4.4 400 1500 100 DLW5BS 5.5 5.4 4.7 400 1500 100 DLW5BT 5.5 5.4 2.7 700 2500 100 Direction of feed c: Depth of Cavity (in mm) Block Type EMIFILr Dimension of the cavity is measured at the bottom side. "Minimum Quantity" means the number of units of each delivery or order. The quantity should be an integral multiple of the "Minimum Quantity". !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 182 PL p Chip Common Mode Choke Coil Packaging a b d 24.0±0.2 +0.1 ø1.5–0 11.75±0.1 2.0±0.1 1.75±0.1 4.0±0.1 Chip Ferrite Bead Minimum Quantity and Dimensions of 24mm Width Embossed Tape 12.0±0.1 c Direction of Feed Part Number Minimum Qty. (pcs.) a b c d ø178mm Reel ø330mm Reel Bulk 13.5 6.5 9.4 0.5 125 500 50 Block Type EMIFILr Packaging Chip Common Mode Choke Coil PLT10H Cavity Size (mm) Chip EMIFILr (in mm) Dimension of the cavity is measured at the bottom side. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 183 Chip Common Mode Choke Coil Design Kits Chip Ferrite Bead DL p Block Type EMIFILr Design Kits Chip Common Mode Choke Coil Chip EMIFILr oEKEMDL21L (Chip Common Mode Choke Coils) No. Part Number Quantity (pcs.) Common Mode Impedance (at 100MHz, 20 degrees C) Rated Voltage (Vdc) Rated Current (mA) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 DLW21HN670SQ2 DLW21HN900SQ2 DLW21HN121SQ2 DLW21HN181SQ2 DLW21SN670SQ2 DLW21SN900SQ2 DLW21SN121SQ2 DLW21SN181SQ2 DLW21SN261SQ2 DLW21SN371SQ2 DLW21SN670HQ2 DLW21SN900HQ2 DLW21SN121HQ2 DLW21SR670HQ2 DLP0NSA150HL2 DLP0NSC280HL2 DLP0NSN670HL2 DLP0NSN900HL2 DLP0NSN121HL2 DLP1NDN350HL4 DLP1NDN670HL4 DLP1NDN900HL4 DLP11SA350HL2 DLP11SA670HL2 DLP11SA900HL2 DLP11SN670SL2 DLP11SN121SL2 DLP11SN161SL2 DLP11SN900HL2 DLP11SN201HL2 DLP11SN241HL2 DLP11SN281HL2 DLP11SN331HL2 DLP11TB800UL2 DLP2ADA350HL4 DLP2ADA670HL4 DLP2ADA900HL4 DLP2ADN670HL4 DLP2ADN900HL4 DLP2ADN121HL4 DLP2ADN161HL4 DLP2ADN201HL4 DLP2ADN241HL4 DLP2ADN281HL4 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 67Ω±25% 90Ω±25% 120Ω±25% 180Ω±25% 67Ω±25% 90Ω±25% 120Ω±25% 180Ω±25% 260Ω±25% 370Ω±25% 67Ω±25% 90Ω±25% 120Ω±25% 67Ω±25% 15Ω±5Ω 28Ω±20% 67Ω±20% 90Ω±20% 120Ω±20% 35Ω±20% 67Ω±20% 90Ω±20% 35Ω±20% 67Ω±20% 90Ω±20% 67Ω±20% 120Ω±20% 160Ω±20% 90Ω±20% 200Ω±20% 240Ω±20% 280Ω±20% 330Ω±20% 80Ω±25% 35Ω±20% 67Ω±20% 90Ω±20% 67Ω±20% 90Ω±20% 120Ω±20% 160Ω±20% 200Ω±20% 240Ω±20% 280Ω±20% 50 50 50 50 50 50 50 50 50 50 20 20 20 20 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 330 330 280 250 400 330 370 330 300 280 320 280 280 400 100 100 110 100 90 100 80 60 170 150 150 180 140 120 150 110 100 90 80 100 150 130 120 140 130 120 100 90 80 80 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 184 DLp Chip Common Mode Choke Coil Design Kits Part Number Quantity (pcs.) Common Mode Impedance (at 100MHz, 20 degrees C) Rated Voltage (Vdc) Rated Current (mA) 1 2 3 4 5 6 7 8 9 10 11 DLW5AHN402SQ2 DLW5BSN191SQ2 DLW5BSN351SQ2 DLW5BSN102SQ2 DLW5BSN152SQ2 DLW5BSN302SQ2 DLW5BTN101SQ2 DLW5BTN251SQ2 DLW5BTN501SQ2 DLW5BTN102SQ2 DLW5BTN142SQ2 5 5 5 5 5 5 5 5 5 5 5 4000Ω (Typ.) 190Ω (Typ.) 350Ω (Typ.) 1000Ω (Typ.) 1500Ω (Typ.) 3000Ω (Typ.) 100Ω (Typ.) 250Ω (Typ.) 500Ω (Typ.) 1000Ω (Typ.) 1400Ω (Typ.) 50 50 50 50 50 50 50 50 50 50 50 200 5000 2000 1500 1000 500 6000 5000 4000 2000 1500 Block Type EMIFILr Design Kits Chip Common Mode Choke Coil Chip EMIFILr No. Chip Ferrite Bead oEKEMDCC5C (Chip Common Mode Choke Coils for DC Power Line / SMD Block type EMIFILr for Power Line) !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 185 Large Current Common Mode Choke Coils (Automotive Available) Design Kits Chip Ferrite Bead PL p oEKEPPL10B (Common Mode Choke Coil) Part Number Quantity (pcs.) Common Mode Impedance (at 10MHz, 20 degrees C) Rated Voltage (Vdc) Rated Current (A) 1 2 3 4 PLT10HH401100PN PLT10HH501100PN PLT10HH9016R0PN PLT10HH1026R0PN 6 6 6 6 400Ω (Typ.) 500Ω (Typ.) 900Ω (Typ.) 1000Ω (Typ.) 100 100 100 100 10 10 6 6 Block Type EMIFILr Design Kits Chip Common Mode Choke Coil Chip EMIFILr No. !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. C31E.pdf Mar.28,2011 186 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Murata: DLW5AHN402SQ2L DLW5BSN152SQ2L DLW5BSN191SQ2L DLW5BSN102SQ2L DLW5BSN302SQ2L DLW21SN261SQ2L DLW5BSN351SQ2L DLP31SN221SL2B DLP31SN221SL2L DLP31SN121SL2L DLP31DN441ML4L DLP31DN471SL4L DLW21HN670SQ2L DLW21SN670SQ2L DLW21SN181SQ2L DLP11SN161SL2L DLW21HN181SQ2L DLP11SN201SL2L DLW31SN601SQ2L DLP31DN900SL4L DLW21HN121SQ2L DLP31SN551SL2L DLW21SN261SQ2B DLW5BTN102SQ2L DLW5BTN142SQ2L DLW5BTN251SQ2L DLW5BTN501SQ2L DLW5BSN102SQ2B DLP31SN221ML2B DLM2HGN601SZ3L DLP11SN900SL2L DLW31SN900SQ2L DLP31DN900ML4L DLP0NSN900HL2L DLP2ADN121HL4L DLP31SN221ML2L DLW31SN102SQ2L DLP31DN900SL4 DLW31SN222SQ2L DLW31SH222SQ2L DLP31DN201ML4L DLW21SN121SQ2L DLW21SN371SQ2L DLP31DN131ML4L DLP31DN201SL4L DLW21HN900SQ2L DLP11SN121SL2L DLP31DN321ML4L DLW21SN900SQ2L DLW31SN261SQ2L DLW31SN161SQ2L DLP31DN161SL4L DLP31DN361SL4L DLP0NSN121HL2L DLP0NSN670HL2L DLP11SA350HL2L DLP11SA670HL2L DLP11SA900HL2L DLP11SN241HL2L DLP11SN281HL2L DLP11SN331HL2L DLP11SN900HL2L DLP2ADN161HL4L DLP2ADN201HL4L DLP2ADN241HL4L DLP2ADN281HL4L DLP2ADN670HL4L DLP2ADN900HL4L DLW21SN121HQ2L DLW21SN670HQ2L DLW21SR670HQ2L DLW43SH101XK2L DLW43SH510XK2B DLP11TB800UL2L DLW5BTN501SQ2K DLW21SN900HQ2L DLW5BTN101SQ2L DLP31SN121ML2L DLP31SN551ML2L DLP11SN201HL2L DLP11SN670SL2L DLP31DN441ML4B DLM11GN601SZ2D DLM11GN601SD2D DLW43SH101XP2L DLW43SH110XK2L DLW43SH220XK2L