TI1 DVITDM8148CCYE1 Davinci video processor Datasheet

TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
TMS320DM814x DaVinci™
Video Processors
Check for Samples: TMS320DM8148, TMS320DM8147
1 High-Performance System-on-Chip (SoC)
1.1
Features
12
• High-Performance DaVinci Video Processors
– Up to 1-GHz ARM® Cortex®-A8 RISC Core
– Up to 750-MHz C674x™ VLIW DSP
– Up to 6000 MIPS and 4500 MFLOPS
– Fully Software-Compatible with C67x+™,
C64x+™
• ARM Cortex-A8 Core
– ARMv7 Architecture
• In-Order, Dual-Issue, Superscalar
Processor Core
• Neon™ Multimedia Architecture
• Supports Integer and Floating Point
• Jazelle® RCT Execution Environment
• ARM Cortex-A8 Memory Architecture
– 32KB of Instruction and Data Caches
– 512KB of L2 Cache
– 64KB of RAM, 48KB of Boot ROM
• TMS320C674x Floating-Point VLIW DSP
– 64 General-Purpose Registers (32-Bit)
– Six ALU (32-/40-Bit) Functional Units
• Supports 32-Bit Integer, SP (IEEE Single
Precision/32-Bit) and DP (IEEE Double
Precision/64-Bit) Floating Point
• Supports up to Four SP Adds Per Clock
and Four DP Adds Every Two Clocks
• Supports up to Two Floating-Point (SP or
DP) Approximate Reciprocal or Square
Root Operations Per Cycle
– Two Multiply Functional Units
• Mixed-Precision IEEE Floating-Point
Multiply Supported up to:
– 2 SP x SP → SP Per Clock
– 2 SP x SP → DP Every Two Clocks
– 2 SP x DP → DP Every Three Clocks
– 2 DP x DP → DP Every Four Clocks
• Fixed-Point Multiply Supports Two 32 x
32 Multiplies, Four 16 x 16-Bit Multiplies
Including Complex Multiplies, or Eight 8 x
8-Bit Multiplies per Clock Cycle
• C674x Two-Level Memory Architecture
– 32KB of L1P RAM/Cache With EDC
•
•
•
•
•
•
•
•
– 32KB of L1D RAM/Cache
– 256KB of L2 Unified Mapped RAM/Caches
With ECC
System Memory Management Unit (MMU)
– Maps C674x DSP and EDMA TC Memory
Accesses to System Addresses
128KB of On-Chip Memory Controller (OCMC)
RAM
Imaging Subsystem (ISS)
– Camera Sensor Connection
• Parallel Connection for Raw (up to 16-Bit)
and BT.656 or BT.1120 (8- and 16-Bit)
– Image Sensor Interface (ISIF) for Handling
Image and Video Data From the Camera
Sensor
– Resizer
• Resizing Image and Video From 1/16x to
8x
• Generating Two Different Resizing
Outputs Concurrently
Programmable High-Definition Video Image
Coprocessing (HDVICP v2) Engine
– Encode, Decode, Transcode Operations
– H.264, MPEG-2, VC-1, MPEG-4, SP/ASP,
JPEG/MJPEG
Media Controller
– Controls the HDVPSS, HDVICP2, and ISS
SGX530 3D Graphics Engine
– Delivers up to 25 MPoly/sec
– Universal Scalable Shader Engine
– Direct3D Mobile, OpenGLES 1.1 and 2.0,
OpenVG 1.0, OpenMax API Support
– Advanced Geometry DMA Driven Operation
– Programmable HQ Image Anti-Aliasing
Endianness
– ARM and DSP Instructions/Data – Little
Endian
HD Video Processing Subsystem (HDVPSS)
– Two 165-MHz, 2-channel HD Video Capture
Modules
• One 16-/24-Bit Input or Dual 8-Bit SD
Input Channels
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Products conform to
specifications per the terms of the Texas Instruments standard warranty. Production
processing does not necessarily include testing of all parameters.
Copyright © 2011–2013, Texas Instruments Incorporated
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
•
•
•
•
•
•
2
One 8-/16-/24-Bit Input and One 8-Bit Only
Input Channels
– Two 165-MHz HD Video Display Outputs
• One 16-, 24-, or 30-Bit Output and One 16or 24-Bit Output
– Composite or S-Video Analog Output
– Macrovision® Support Available
– Digital HDMI 1.3 Transmitter With Integrated
PHY
– Advanced Video Processing Features Such
as Scan, Format, Rate Conversion
– Three Graphics Layers and Compositors
Dual 32-Bit DDR2/DDR3 SDRAM Interfaces
– Supports up to DDR2-800 and DDR3-1066
– Up to Eight x 8 Devices Total 2GB of Total
Address Space
– Dynamic Memory Manager (DMM)
• Programmable Multi-Zone Memory
Mapping and Interleaving
• Enables Efficient 2D Block Accesses
• Supports Tiled Objects in 0°, 90°, 180°, or
270° Orientation and Mirroring
• Optimizes Interlaced Accesses
General-Purpose Memory Controller (GPMC)
– 8- or 16-Bit Multiplexed Address and Data
Bus
– 512MB of Address Space Divided Among up
to 8 Chip Selects
– Glueless Interface to NOR Flash, NAND
Flash (BCH/Hamming Error Code Detection),
SRAM and Pseudo-SRAM
– Error Locator Module (ELM) Outside of
GPMC to Provide Up to 16-Bit or 512-Byte
Hardware ECC for NAND
– Flexible Asynchronous Protocol Control for
Interface to FPGA, CPLD, ASICs, and so
Forth
Enhanced Direct Memory Access (EDMA)
Controller
– Four Transfer Controllers
– 64 Independent DMA Channels and 8
Independent QDMA Channels
Dual Port Ethernet (10/100/1000 Mbps) With
Optional Switch
– IEEE 802.3 Compliant (3.3-V I/O Only)
– MII/RMII/GMII/RGMII Media Independent
Interfaces
– Management Data I/O (MDIO) Module
– Reset Isolation
– IEEE 1588 Time-Stamping and Industrial
Ethernet Protocols
Dual USB 2.0 Ports With Integrated PHYs
– USB2.0 High- and Full-Speed Clients
– USB2.0 High-, Full-, and Low-Speed Hosts,
www.ti.com
High-Performance System-on-Chip (SoC)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
or OTG
– Supports End Points 0–15
One PCI Express 2.0 Port With Integrated PHY
– Single Port With One Lane at 5.0 GT/s
– Configurable as Root Complex or Endpoint
Eight 32-Bit General-Purpose Timers
(Timer1–8)
One System Watchdog Timer (WDT0)
Six Configurable UART/IrDA/CIR Modules
– UART0 With Modem Control Signals
– Supports up to 3.6864 Mbps UART0/1/2
– Supports up to 12 Mbps UART3/4/5
– SIR, MIR, FIR (4.0 MBAUD), and CIR
Four Serial Peripheral Interfaces (SPIs) (up to
48 MHz)
– Each With Four Chip Selects
Three MMC/SD/SDIO Serial Interfaces (up to
48 MHz)
– Three Supporting up to 1-, 4-, or 8-Bit Modes
Dual Controller Area Network (DCAN) Modules
– CAN Version 2 Part A, B
Four Inter-Integrated Circuit (I2C Bus) Ports
Six Multichannel Audio Serial Ports (McASPs)
– Dual Ten Serializer Transmit and Receive
Ports
– Quad Four Serializer Transmit and Receive
Ports
– DIT-Capable For S/PDIF (All Ports)
Multichannel Buffered Serial Port (McBSP)
– Transmit and Receive Clocks up to 48 MHz
– Two Clock Zones and Two Serial Data Pins
– Supports TDM, I2S, and Similar Formats
Serial ATA (SATA) 3.0 Gbps Controller With
Integrated PHY
– Direct Interface to One Hard Disk Drive
– Hardware-Assisted Native Command
Queuing (NCQ) from up to 32 Entries
– Supports Port Multiplier and CommandBased Switching
Real-Time Clock (RTC)
– One-Time or Periodic Interrupt Generation
Up to 128 General-Purpose I/O (GPIO) Pins
One Spin Lock Module with up to 128 Hardware
Semaphores
One Mailbox Module with 12 Mailboxes
On-Chip ARM ROM Bootloader (RBL)
Power, Reset, and Clock Management
– Multiple Independent Core Power Domains
– Multiple Independent Core Voltage Domains
– Support for Three Operating Points (OPP100,
OPP120, OPP166) per Voltage Domain
– Clock Enable and Disable Control for
Subsystems and Peripherals
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
• 32KB of Embedded Trace Buffer (ETB) and
5-Pin Trace Interface for Debug
• IEEE 1149.1 (JTAG) Compatible
• 684-Pin Pb-Free BGA Package (CYE Suffix),
0.8-mm Ball Pitch With Via Channel
1.2
•
•
•
•
•
•
•
Technology to Reduce PCB Cost
• 45-nm CMOS Technology
• 1.8- and 3.3-V Dual Voltage Buffers for General
I/O
Applications
HD Video Conferencing - Skype® Endpoints
Video Surveillance DVRs, IP Netcam
Digital Signage
Media Players and Adapters
Mobile Medical Imaging
Network Projectors
Home Audio and Video Equipment
High-Performance System-on-Chip (SoC)
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
3
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
1.3
www.ti.com
Description
TMS320DM814x DaVinci video processors are highly integrated, programmable platforms that leverage
the DaVinci processor technology to meet the processing needs of the following applications to name a
few:
• HD Video Conferencing - Skype endpoints
• Video Surveillance DVRs
• IP Netcam
• Digital Signage
• Media Players and Adapters
• Mobile Medical Imaging
• Network Projectors
• Home Audio and Video Equipment
The device enables Original-Equipment Manufacturers (OEMs) and Original-Design Manufacturers
(ODMs) to quickly bring to market devices featuring robust operating systems support, rich user interfaces,
and high processing performance through the maximum flexibility of a fully integrated mixed processor
solution. The device also combines programmable video and audio processing with a highly integrated
peripheral set.
The TMS320DM814x DaVinci video processors also present OEMs and ODMs with new levels of
processor scalability and software reuse. An OEM or ODM that used the AM387x processors in a design
and can make a similar product with added features could scale up to the pin-compatible and softwarecompatible TMS320DM814x processors from TI. The TMS320DM814x DaVinci video processors add a
powerful C674x DSP core along with a video encoder and decoder to the hardware on the AM38x.
Additionally, OEMs or ODMs that have used the AM387x or DM814x processors and find a need for a
faster ARM and DSP core performance could scale up to the software-compatible AM389x or
TMS320DM816x devices with higher core speeds.
Programmability is provided by an ARM Cortex-A8 RISC CPU with Neon extension, TI C674x VLIW
floating-point DSP core, and high-definition video and imaging coprocessors. The ARM lets developers
keep control functions separate from A/V algorithms programmed on the DSP and coprocessors, thus
reducing the complexity of the system software. The ARM Cortex-A8 32-Bit RISC Core with Neon floatingpoint extension includes: 32KB of Instruction cache; 32KB of Data cache; 512KB of L2 Cache; 48KB of
Boot ROM; and 64KB of RAM.
The rich peripheral set provides the ability to control external peripheral devices and communicate with
external processors. For details on each of the peripherals, see the related sections in this document and
the associated peripheral reference guides. The peripheral set includes:
• HD Video Processing Subsystem
• Dual Port Gigabit Ethernet MACs (10/100/1000 Mbps) [Ethernet Switch] with MII/RMII/GMII/RGMII and
MDIO interface supporting IEEE 1588 Time-Stamping and Industrial Ethernet Protocols
• Two USB ports with integrated 2.0 PHY
• PCIe x1 GEN2 Compliant interface
• Two 10-serializer McASP audio serial ports (with DIT mode)
• Four quad-serilaizer McASP audio serial ports (with DIT mode)
• One McBSP multichannel buffered serial port
• Six UARTs with IrDA and CIR support
• Four SPI serial interfaces
• Three MMC/SD/SDIO serial interfaces
• Four I2C master and slave interfaces
• Parallel Camera Interface (CAM)
• Up to 128 General-Purpose I/Os (GPIOs)
4
High-Performance System-on-Chip (SoC)
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
•
•
•
•
•
•
•
•
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Eight 32-bit general-purpose timers
System watchdog timer
Dual DDR2, and DDR3 SDRAM interfaces
Flexible 8- or 16-bit asynchronous memory interface
Two Controller Area Network (DCAN) modules
Spin Lock
Mailbox
Serial Hard Disk Drive Interface (SATA 300)
The TMS320DM814x DaVinci video processors also include a high-definition video and imaging
coprocessor 2 (HDVICP2), and an SGX530 3D graphics engine to off-load many video and imaging
processing tasks from the DSP core, making more DSP MIPS available for common video and imaging
algorithms. Additionally, it has a complete set of development tools for both the ARM and DSP, which
include C compilers, a DSP assembly optimizer to simplify programming and scheduling, and a Microsoft®
Windows® debugger interface for visibility into source code execution.
The C674x DSP core is the high-performance floating-point DSP generation in the TMS320C6000 DSP
platform and is code-compatible with previous generation C64x Fixed-Point and C67x Floating-Point DSP
generation. The C674x Floating-Point DSP processor uses 32KB of L1 program memory with EDC and
32KB of L1 data memory. Up to 32KB of L1P can be configured as program cache. The remaining
memory is noncacheable no-wait-state program memory. Up to 32KB of L1D can be configured as data
cache. The remaining memory is noncacheable no-wait-state data memory. The DSP has 256KB of L2
RAM with ECC, which can be defined as SRAM, L2 cache, or a combination of both. All C674x L3 and offchip memory accesses are routed through an MMU.
High-Performance System-on-Chip (SoC)
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
5
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
1.4
www.ti.com
Functional Block Diagram
Figure 1-1 shows the functional block diagram of the device.
ARM Subsystem
512 KB L2 Cache
Boot ROM
48 KB
RAM
64 KB
ICE Crusher
32KB
L1 Pgm
32 KB
L1 Data
256 KB L2 Cache
AET
Media Controller
32 KB
D-Cache
C674x
DSP CPU
TM
128 KB On-Chip RAM
32 KB
I-Cache
NEON
FPU
High Definition Video Image
Coprocessor (HDVICP2)
DSP Subsystem
(A)
TM
SGX530 3D Graphics Engine
Cortex -A8
CPU
Video Processing
Subsystem
Imaging
Subsystem
Video Capture
Parallel Cam Input
Display Processing
HD OSD
SD OSD
HD VENC
SD VENC
HDMI Xmt
SD DACs
Resizer
System MMU
System Interconnect
Peripherals
Serial Interfaces
Real-Time
Clock
PRCM
GP Timer
(8)
JTAG
Watchdog
Timer
Spin Lock
Mailbox
Connectivity
Program/Data Storage
McASP
(6)
McBSP
DDR2/3
32-bit
(2)
SPI
(4)
I 2C
(4)
SATA
3Gbp/s
(1 Drives)
DCAN
(2)
UART
(6)
GPMC
+
ELM
EDMA
System Control
EMAC
(R)(G)MII
(2)
MDIO
USB 2.0
Ctlr/PHY
(2)
PCIe 2.0
(One x1
Port)
MMC/SD/
SDIO
(3)
A. SGX530 is only available on the DM8148 device.
Figure 1-1. TMS320DM814x DaVinci video Processors Functional Block Diagram
6
High-Performance System-on-Chip (SoC)
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
......... 1
............................................. 1
1.2
Applications .......................................... 3
1.3
Description ........................................... 4
1.4
Functional Block Diagram ........................... 6
Revision History .............................................. 8
2 Device Overview ....................................... 12
2.1
Device Comparison ................................ 12
2.2
Device Characteristics .............................. 12
2.3
Device Compatibility ................................ 14
1
7.2
1.1
..............................................
...........................................
7.5
Interrupts ..........................................
Peripheral Information and Timings .............
8.1
Parameter Information ............................
5
6
Reset
189
7.4
Clocking
197
221
Recommended Clock and Control Signal Transition
Behavior ........................................... 222
8.3
Controller Area Network Interface (DCAN)
8.4
EDMA
8.7
8.8
Electrical Characteristics Over Recommended
Ranges of Supply Voltage and Operating
Temperature (Unless Otherwise Noted) .......... 179
Power, Reset, Clocking, and Interrupts
7.1
8.6
C674x™ DSP Overview
.........
181
Power, Reset and Clock Management (PRCM)
Module ............................................ 181
223
225
232
236
251
General-Purpose Memory Controller (GPMC) and
Error Location Module (ELM) ..................... 254
High-Definition Multimedia Interface (HDMI) ...... 271
High-Definition Video Processing Subsystem
(HDVPSS) ......................................... 274
8.11
Inter-Integrated Circuit (I2C)
8.12
Imaging Subsystem (ISS)
8.14
8.15
8.16
8.17
8.18
8.19
8.20
8.21
......................
.........................
DDR2/DDR3 Memory Controller ..................
Multichannel Audio Serial Port (McASP) ..........
Multichannel Buffered Serial Port (McBSP) .......
280
284
287
324
332
MultiMedia Card/Secure Digital/Secure Digital Input
Output (MMC/SD/SDIO) ........................... 337
Peripheral Component Interconnect Express (PCIe)
..................................................... 340
.....................
Serial Peripheral Interface (SPI) ..................
Timers .............................................
Serial ATA Controller (SATA)
347
351
358
Universal Asynchronous Receiver/Transmitter
(UART) ............................................ 360
....................
.............
9.1
Device Support ....................................
9.2
Documentation Support ...........................
9.3
Community Resources ............................
Mechanical ............................................
10.1 Thermal Data for CYE-04 (Top Hat) ..............
10.2 Packaging Information ............................
8.22
10
.......
.............................................
Emulation Features and Capability ...............
Ethernet MAC Switch (EMAC SW) ................
General-Purpose Input/Output (GPIO) ............
8.9
8.10
8.13
9
214
221
8.2
............................ 16
2.6
System Memory Management Unit (MMU) ........ 20
2.7
Media Controller Overview ......................... 21
2.8
HDVICP2 Overview ................................ 21
2.9
SGX530 Overview .................................. 22
2.10 Spinlock Module Overview ......................... 22
2.11 Mailbox Module Overview .......................... 23
2.12 Memory Map Summary ............................. 24
Device Pins ............................................. 34
3.1
Pin Maps ........................................... 34
3.2
Terminal Functions ................................. 43
Device Configurations .............................. 153
4.1
Control Module Registers ......................... 153
4.2
Boot Modes ....................................... 153
4.3
Pin Multiplexing Control ........................... 159
4.4
Handling Unused Pins ............................ 170
4.5
DeBugging Considerations ........................ 170
System Interconnect ................................ 172
Device Operating Conditions ...................... 176
6.1
Absolute Maximum Ratings ....................... 176
6.2
Recommended Operating Conditions ............. 177
6.3
Power-On Hours (POH) ........................... 178
6.4
7
8
7.3
ARM® Cortex™-A8 Microprocessor Unit (MPU)
Subsystem Overview ............................... 14
2.5
4
Features
8.5
2.4
3
Power .............................................. 181
High-Performance System-on-Chip (SoC)
Universal Serial Bus (USB2.0)
362
Device and Documentation Support
370
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Contents
370
371
371
372
372
372
7
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
This data manual revision history highlights the technical changes made to the SPRS647D device-specific
data manual to make it an SPRS647E revision.
Scope: Applicable updates to the DM814x DaVinci™ Video DMP device family, specifically relating to the
TMS320DM8148/47 devices (Silicon Revisions 3.0, 2.1), which are now in the production data (PD) stage
of development have been incorporated.
•
•
•
•
•
•
•
•
•
•
•
Updated/Changed Power-Up Sequence
Updated/Changed Power-Down Sequence
Low-end OPP combinations no longer supported (CVDD_x < CVDD)
Added RXACTIVE Function (Bit 18) to PINCTRLx Register Description
Added Power-On Hours (POH) section
Added Latch-Up Performance Absolute Maximum Ratings
DDR2/DDR3 supports up to 533 MHz
OPP50 is not supported
SmartReflex™ (AVS) is not supported
Deep Sleep Mode is not supported
HDMI HDCP encryption is not supported
SEE
8
ADDITIONS/MODIFICATIONS/DELETIONS
Global
•
•
•
Replaced all instances of "DSP/EDMA MMU" with "System MMU"
Deleted all references to OPP50 and Deep Sleep Mode
Deleted the TMS320DM8146 device along with any device-specific information; no longer
supported
Section 1
Features
•
•
Updated/Changed description the HD Video Processing Subsystem (HDVPSS)
Updated/Changed the Dual 32-Bit DDR2/DDR3 SDRAM Interfaces sub-bullet from "Supports up to
DDR2-800 and DDR3-800" to "Supports up to DDR2-800 and DDR3-1066"
Section 2.2
Device Characteristics
Table 2-2, Characteristics of the Processor:
•
Updated/Changed the HD Video Processing Subsystem (HDVPSS) row
•
Updated/Changed Core Logic (V), OPP100, OPP120 range from "0.95 V – 1.20 V" to "1.10 V –
1.20 V"
Section 2.12.4.2
L4 Slow Peripheral
Memory Map
Table 2-7, L4 Slow Peripheral Memory Map:
•
Updated/Changed 0x4818_8000–0x4818_BFFF Device Name from "SmartReflex0/1 Peripheral
and Support Registers" to "Reserved"
•
Updated/Changed 0x4819_0000–0x4819_3FFF Device Name from "SmartReflex2/3 Peripheral
and Support Registers" to "Reserved"
Section 3.2.7
General-Purpose
Input/Outputs (GPIOs)
Table 3-11, GP1 Terminal Functions:
•
Added "The ENLVCMOS bit in the MLBP_DAT_IO_CTRL register...." to the pin descriptions for
pins GP1[10:7] (V2, V1, W2, and W1 respectively).
Section 3.2.25
Reserved Pins
Table 3-48, Reserved Terminal Functions:
•
Updated/Changed TYPE for Signal No. Y14 (RSV4) and AC8 (RSV5) from "S" to "I"
Contents
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
SEE
ADDITIONS/MODIFICATIONS/DELETIONS
Section 4.3, Pin Multiplexing Control:
•
Updated/Changed bit 18 from "RSV" to "RXACTIVE"
Section 4
Device Configurations
Table 4-11, PINCNTL1 – PINCNTL270 (PINCNTLx) Registers Bit Descriptions:
•
Updated/Changed the MUXMODE[7:0] Description from "Values other than those ..." to "A value
of zero results ..."
•
Updated/Changed bit 18 description to now support RXACTIVE
Table 4-13, PINCNTLx Registers MUXMODE Functions:
•
Updated/Changed PINCNTL173 row under 0x20 from "UART2_TXD(M1)" to "UART2_TXD(M0)"
•
Updated/Changed PINCNTL231 under 0x80 from "GP3[30](M0)" to "GP3[30](M1)"
Section 4.4, Handling Unused Pins:
•
Added "Unless otherwise noted" to the beginning of, "All supply pins must always ..."
Section 6
Device Operating
Conditions
Section 6.1, Absolute Maximum Ratings:
•
Deleted the "V I/O...(Transient Overshoot/Undershoot)" rows of Input and Output voltage ranges
•
Added Latch-Up Performance row and Latch-Up footnotes
•
Updated/Changed ESD-HBM footnote to "Level listed is passing level per ANSI/ESDA/JEDEC J5001..."
•
Updated/Changed ESD-CDM footnote to "Level listed is passing level per EIA-JEDEC JESD22C101E..."
Section 6.3, Power on Hours (POH):
•
Added Power-On Hour (POH) section [New]
Section 7.2.2.1
Dynamic Voltage
Frequency Scaling
(DVFS)
Table 7-5, Supported OPP Combinations:
•
Deleted lower-end OPP combinations supported for ARM, DSP, and HDVICP2
Section 7.2.8.1
Power-Up Sequence
Table 7-6 , Power-Up Sequence Ramping Values:
•
Added NO. 1 MIN value of "0" ms.
•
Updated/Changed NO. 1 description to "1.8 V and DVDD_DDR[x] supplies stable..."
•
Added NO. 13, "CVDD variable supply ramp...."
•
Updated/Changed Figure 7-1 according to table changes
•
Deleted 3.3 V Supplies Rising Before 1.8 V Supplies Delta Figure (was Figure 7.2) and associated
footnote references
•
Deleted footnote, "The 3.3 V supplies must be..."
Section 7.2.8.2, Power-Down Sequence:
•
Added, "Ramping down all supplies at the same time...For proper device..." paragraph
Section 7.2.8.2
Power-Down Sequence
Table 7-7, Power-Down Sequence Ramping Values:
•
Updated/Changed "The 1.5-/1.8-V DVDD_DDR[x]..." footnote
•
Updated/Changed figure reference to Figure 7-3
•
Added NO. 14, "CVDD_x variable supplies ramp-down..."
•
Added associated footnote, "CVDD_x must never exceed CVDD by more than 150mV"
Figure 7-2, Power-Down Sequence:
•
Updated/Changed figure according to table changes
Figure 7-3,1.8 V Supplies Falling Before 3.3 V Supplies Delta:
•
Added figure [New]
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Contents
9
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
SEE
www.ti.com
ADDITIONS/MODIFICATIONS/DELETIONS
Section 7.4.1.1, Using the Internal Oscillators:
Table 7-11, Requirements for Crystal Circuit on the Device Oscillator (DEVOSC):
•
Added three conditions and the MAX values to the Crystal Frequency Stability PARAMETER
Table 7-15, Timing Requirements for DEVOSC_MXI/DEV_CLKIN
•
Added three conditions and the MAX values to the Frequency Stability PARAMETER
Section 7.4
Clocking
Section 7.4.3, AUD_CLKINx Input Clocks:
•
Added section [New]
Section 7.4.4, CLKIN32 Input Clock:
•
Added "/8" to the TIMER1/2/3/4/5/6/7 bullet
Section 7.4.7, Input/Output Clocks Electrical Data/Timing:
•
Added Table 7-17, Timing Requirements for AUD_CLKINx [New]
•
Added Figure 7-14, AUD_CLKINx Timing [New]
Section 7.4.8, PLLs:
•
Deleted PLL Electrical Data/Timing subsection
Section 7.4.9
SYSCLKs
Table 7-26, Maximum SYSCLK Clock Frequencies:
•
Added footnote, "The maximum frequencies listed..."
Section 7.4.10
Module Clocks
Table 7-27, Maximum Module Clock Frequencies:
•
Updated/Changed Media Controller CLOCK SOURCES from "PLL_MEDIACTL" to
"PLL_MEDIACTL/2"
•
Updated/Changed Media Controller MAX FREQUENCY OPP100 (MHz) value from "400" to "200"
•
Added footnote, "The maximum frequencies listed..."
Section 8.4.1, EDMA Channel Synchronization Events:
•
Updated/Changed paragraphs
Section 8.4
EDMA
10
Section 8.4.2, EDMA Peripheral Register Descriptions:
•
Added Table 8-5, EDMA Channel Controller (EDMA TPCC) Control Registers
•
Added Table 8-6, EDMA Transfer Controller (EDMA TPTC) Control Registers
Section 8.5.3
IEEE 1149.1 JTAG
Table 8-8, JTAG ID Register Table:
•
Added silicon-revision specific information to the VARIANT bit field
Section 8.6.2.3
EMAC RGMII Electrical
Data/Timing
•
Section 8.10.1
HDVPSS Electrical
Data/Timing
Table 8-42, Timing Requirements for HDVPSS Input:
•
Deleted NO. 7, tt(CLK), Transition time, VIN[x]A_CLK (10%-90%)
•
Deleted NO. 7, tt(CLK), Transition time, VIN[x]B_CLK (10%-90%)
Section 8.13.4,
DDR2/DDR3 Memory
Controller Electrical
Data/Timing
Table 8-53, Switching Characteristics Over Recommended Operating Conditions for DDR2/DDR3
Memory Controller:
•
Updated/Changed NO. 1, tc(DDR_CLK) , Cycle time, DDR[x]_CLK, DDR2/DDR3 mode to DDR2
mode
•
Added additional row to NO.1, tc(DDR_CLK), Cycle time, DDR[x]_CLK: DDR3 mode
Section 8.13.4.1
DDR2 Routing
Specifications
Section 8.13.4.1.1.1, DDR2 Interface Schematic:
•
Updated/Changed the sentence from, "... pins by pulling the non-inverted DQS pin..." to "...
DDR[x]_DQS[n] pins to the corresponding..."
•
Updated/Changed a sentence from, "... inverted DQS pin..." to "... DDR[x]_DQS[n] pins..."
•
Added sentence, "The DVDD_DDR[x] and VREFSSTL_DDR[x] power..."
Section 8.13.4.1.2
DDR2 CK and
ADDR_CTRL Routing
Table 8-63, CK and ADDR_CTRL Routing Specification:
•
Updated/Changed the "Series terminator,...the DSP" footnote to "Series terminator,..the processor"
Section 8.13.4.2
DDR3 Routing
Specifications
Section 8.13.4.2.4, DDR3 Interface Schematic:
•
Combined 16-Bit and 32-Bit DDR3 Interface subsections
•
Deleted repeated figure references
•
Deleted the sentence, "and the unused DQS......pulled to ground via 1-kΩ resistors."
•
Added sentence, "The DVDD_DDR[x] and VREFSSTL_DDR[x]..."
Contents
Updated/Changed all instances of "at DSP" to "at device"
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
SEE
ADDITIONS/MODIFICATIONS/DELETIONS
Table 8-66, Compatible JEDEC DDR3 Devices (Per Interface):
Section 8.13.4.2.4.1
Compatible JEDEC DDR3 •
Updated/Changed the max clock rate in footnote, "DDR3 devices with speed...." from "400" MHz to
Devices
"533" MHz
Section 8.14.3
McASP (McASP[5:0])
Electrical Data/Timing
Table 8-78, Timing Requirements for McASP:
•
Updated/Changed McASP1 Only ACLKR/X ext out, MIN value for NO. 5, tsu(AFSRX-ACLKRX), Setup
time, MCA[x]_AFSR/X input valid before MCA[X]_ACLKR/X from "4" to "2" ns.
•
Updated/Changed McASP1 Only ACLKR/X ext out, MIN value for NO. 7,tsu(AXR-ACLKRX), Setup
time, MCA[x]_AXR input valid before MCA[X]_ACLKR/X from "4" to "2" ns.
Section 8.15
Multichannel Buffered
Serial Port (McBSP)
Table 8-80, McBSP Registers:
•
Updated/Changed McBSP HEX ADDRESS range from "0x4700 0000 - 0x4700 00C0" to "0x4700
0100 – 0x4700 01C0" (DDR_REG to STATUS_REG)
•
Added McBSP registers in HEX ADDRESS range "0x4700 0000 – 0x4700 004C" (REVNB to
DMATXWAKE_EN)
Section 9.1.2
Figure 9-1, Device Nomenclature:
Device and Development- •
Added "D = -40ºC to 90ºC, Industrial Temperature" to the TEMPERATURE RANGE area
Support Tool
Nomenclature
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Contents
11
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
2 Device Overview
2.1
Device Comparison
Table 2-1 shows a comparison between devices, highlighting the differences.
Table 2-1. DM814x Device Comparison
DEVICES
FEATURES
SGX530
2.2
TMS320DM8148
TMS320DM8147
YES (1)
NONE
Device Characteristics
Table 2-2 provides an overview of the TMS320DM814x DaVinci™ Digital Media Processors, which
includes significant features of the device, including the capacity of on-chip RAM, peripherals, and the
package type with pin count.
Table 2-2. Characteristics of the Processor
HARDWARE FEATURES
DM814x
1 16-/24-bit HD Capture Port or
2 8-bit SD Capture Ports
and
1 8-bit SD Capture Port
and
1 16-/24-/30-bit HD Display Port or
1 8-/16-/24-bit HD Capture Port
and
1 16-24-bit HD Display Port
and
1 HDMI 1.3 Transmitter
and
2 SD Video DACs
HD Video Processing Subsystem (HDVPSS)
1 Parallel Camera Input for Raw (up to
16-bit)
and BT.656/BT.1120 (8/16-bit)
Imaging Subsystem (ISS)
Peripherals
Not all peripherals
pins are available
at the same time
(for more details,
see the Device
Configurations
section).
DDR2/3 Memory Controller
2 (32-bit Bus Widths)
Asynchronous (8-/16-bit bus width)
RAM, NOR, NAND
GPMC + ELM
64 Independent Channels
8 QDMA Channels
EDMA
10/100/1000 Ethernet MAC Switch with Management Data Input/Output
(MDIO)
2 (Supports High- and Full-Speed as a
Device and
High-, Full-, and Low-Speed as a Host,
or OTG)
USB 2.0
PCI Express 2.0
1 Port (1 5.0GT/s lane)
Timers
8 (32-bit General purpose)
and
1 (System Watchdog)
UART
6 (with SIR, MIR, FIR, CIR support and
RTS/CTS flow control)
(UART0 Supports Modem Interface)
SPI
4 (Supports 4 slave devices)
1 (1-bit or 4-bit or 8-bit modes)
and
1 (8-bit mode) or
2 (1-bit or 4-bit modes)
MMC/SD/SDIO
12
1 (with 2 MII/RMII/GMII/RGMII
Interfaces)
Device Overview
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 2-2. Characteristics of the Processor (continued)
HARDWARE FEATURES
DM814x
I2C
4 (Master/Slave)
Media Controller
Controls HDVPSS, HDVICP2, and ISS
McASP
6 (10/10/4/4/4/4 Serializers, Each with
Transmit/Receive and DIT capability)
McBSP
1 (2 Data Pins, Transmit/Receive)
Controller Area Network (DCAN)
2
Serial ATA (SATA) 3.0 Gbps
1 (Supports 1 Hard Disk Drive)
RTC
1
GPIO
Up to 128 pins
Parallel Camera Interface (CAM)
1
Spin Lock Module
1 (up to 128 H/W Semaphores)
Mailbox Module
On-Chip Memory
1 (with 12 Mailboxes)
Size (Bytes)
1088KB RAM, 48KB ROM
Organization
ARM
32KB I-cache
32KB D-cache
512KB L2 Cache
64KB RAM
48KB Boot ROM
DSP
32KB L1 Program (L1P)/Cache (up to
32KB) with EDC
32KB L1 Data (L1D)/Cache (up to 32KB)
256KB Unified Mapped RAM/Cache (L2)
with ECC
ADDITIONAL SHARED MEMORY
128KB On-chip RAM
ARM® Cortex™-A8 Main ID Register Variant/Revision
r3p2
CPU ID + CPU Rev
Control Status Register (CSR.[31:16])
ID
0x1401
C674x
Megamodule
Revision
Revision ID Register (MM_REVID[15:0])
0x0000
JTAG BSDL ID
DEVICE_ID Register (address location: 0x4814_0600)
CPU Frequency
MHz
Cycle Time
ns
Voltage
ARM® Cortex™-A8 1000, 720 MHz
DSP 600 MHz
ARM® Cortex™ -A8 1.0, 1.39 ns
DSP 1.66 ns
OPP100, OPP120
Core Logic (V)
OPP166
I/O (V)
1.10 V – 1.20 V
1.35 V
1.5 V, 1.8 V, 3.3 V
Package
23 x 23 mm [Flip Chip Ball Grid Array (FCBGA)]
Process
Technology
μm
Product Status (1)
Product Preview (PP),
Advance Information (AI),
or Production Data (PD)
(1)
see Section 8.5.3.1, JTAG ID (JTAGID)
Register Description
684-Pin BGA (CYE) [with Via Channel
Technology]
0.045 μm
PD
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Overview
13
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
2.3
Device Compatibility
2.4
ARM® Cortex™-A8 Microprocessor Unit (MPU) Subsystem Overview
The ARM® Cortex™-A8 Subsystem is designed to give the ARM Cortex-A8 Master control of the device.
In general, the ARM Cortex-A8 is responsible for configuration and control of the various subsystems,
peripherals, and external memories.
The ARM Cortex-A8 Subsystem includes the following features:
• ARM Cortex-A8 RISC processor:
– ARMv7 ISA plus Thumb2™, JazelleX™, and Media Extensions
– Neon™ Floating-Point Unit
– Enhanced Memory Management Unit (MMU)
– Little Endian
– 32KB L1 Instruction Cache
– 32KB L1 Data Cache
– 512KB L2 Cache
• CoreSight Embedded Trace Module (ETM)
• ARM Cortex-A8 Interrupt Controller (AINTC)
• Embedded PLL Controller (PLL_ARM)
• 64KB Internal RAM
• 48KB Internal Public ROM
Figure 2-1 shows the ARM Cortex-A8 Subsystem for the device.
DEVOSC
L3
PLL_ARM
128
System Events
DMM
128 128
128
128
32
128
32
ARM Cortex-A8
Interrupt Controller
(AINTC)
64
48KB ROM
64
64KB RAM
ARM Cortex-A8
128
Trace
32KB L1I$ 32KB L1D$
512KB L2$
ETM
NEON
Arbiter
Debug
ICECrusher
Figure 2-1. ARM Cortex-A8 Subsystem
For more details on the ARM Cortex-A8 Subsystem, see the System MMU section of the Chip Level
Resources chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual
(Literature Number: SPRUGZ8).
2.4.1
ARM Cortex-A8 RISC Processor
The ARM Cortex-A8 Subsystem integrates the ARM Cortex-A8 processor. The ARM Cortex-A8 processor
is a member of ARM Cortex family of general-purpose microprocessors. This processor is targeted at
multi-tasking applications where full memory management, high performance, low die size, and low power
are all important. The ARM Cortex-A8 processor supports the ARM debug architecture and includes logic
to assist in both hardware and software debug. The ARM Cortex-A8 processor has a Harvard architecture
and provides a complete high-performance subsystem, including:
• ARM Cortex-A8 Integer Core
• Superscalar ARMv7 Instruction Set
14
Device Overview
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
•
•
•
•
•
•
•
•
•
•
•
2.4.2
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Thumb-2 Instruction Set
Jazelle RCT Acceleration
CP14 Debug Coprocessor
CP15 System Control Coprocessor
NEON™ 64-/128-bit Hybrid SIMD Engine for Multimedia
Enhanced VFPv3 Floating-Point Coprocessor
Enhanced Memory Management Unit (MMU)
Separate Level-1 Instruction and Data Caches
Integrated Level-2 Cache
128-bit Interconnector-to-System Memories and Peripherals
Embedded Trace Module (ETM).
Embedded Trace Module (ETM)
To support real-time trace, the ARM Cortex-A8 processor provides an interface to enable connection of an
embedded trace module (ETM). The ETM consists of two parts:
• The Trace port which provides real-time trace capability for the ARM Cortex-A8.
• Triggering facilities that provide trigger resources, which include address and data comparators,
counter, and sequencers.
The ARM Cortex-A8 trace port is not pinned out and is, instead, only connected to the system-level
Embedded Trace Buffer (ETB). The ETB has a 32KB buffer memory. ETB enabled debug tools are
required to read/interpret the captured trace data.
For more details on the ETM, see Section 8.5.2, Trace.
2.4.3
ARM Cortex-A8 Interrupt Controller (AINTC)
The ARM Cortex-A8 subsystem contains an interrupt controller (AINTC) that prioritizes all service requests
from the system peripherals and generates either IRQ or FIQ to the ARM Cortex-A8 processor. For more
details on the AINTC, see Section 7.5.1, ARM Cortex-A8 Interrupts.
Note: For General-Purpose devices, the AINTC does not support the generation of FIQs to the ARM
processor.
2.4.4
ARM Cortex-A8 PLL (PLL_ARM)
The ARM Cortex-A8 subsystem contains an embedded PLL Controller (PLL_ARM) for generating the
subsystem’s clocks from the DEV Clock input. For more details on the PLL_ARM, see Section 7.4,
Clocking.
2.4.5
ARM MPU Interconnect
The ARM Cortex-A8 processor is connected through the arbiter to both an L3 interconnect port and a
DMM port. The DMM port is 128 bits wide and provides the ARM Cortex-A8 direct access to the DDR
memories, while the L3 interconnect port is 64 bits wide and provides access to the remaining device
modules.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Overview
15
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
2.5
www.ti.com
C674x™ DSP Overview
The DSP Subsystem includes the following features:
• C674x DSP CPU
• 32KB L1 Program (L1P)/Cache (up to 32KB) with Error Detection Circuitry (EDC)
• 32KB L1 Data (L1D)/Cache (up to 32KB)
• 256KB Unified Mapped RAM/Cache (L2) with Error Correction Circuitry (ECC)
• Direct Connection to the HDVICP2 Host SL2 Port
• Little Endian
32K Bytes
L1P RAM/
Cache
w/EDC
256K Bytes
L2 RAM
w/ ECC
256
HDVICP2 Host
SL2 Port
256
256
Cache Control
Memory Protect
256
Cache Control
Memory Protect
L1P
Bandwidth Mgmt
L2
Bandwidth Mgmt
256
256
256
Instruction Fetch
C674x
Fixed/Floating Point CPU
Register
File A
Register
File B
64
64
256
Power Down
Interrupt
Controller
IDMA
256
CFG
Bandwidth Mgmt
Memory Protect
Cache Control
8 x 32
EMC
L1D
MDMA
L3 (Fast)
Interconnect
SDMA
128
128
32K Bytes
L1D RAM/
Cache
32
L3 (Fast)
Interconnect
Figure 2-2. C674x Megamodule Block Diagram
16
Device Overview
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
2.5.1
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
C674x DSP CPU Description
The C674x central processing unit (CPU) consists of eight functional units, two register files, and two data
paths as shown in Figure 2-2. The two general-purpose register files (A and B) each contain 32 32-bit
registers for a total of 64 registers. The general-purpose registers can be used for data or can be data
address pointers. The data types supported include packed 8-bit data, packed 16-bit data, 32-bit data, 40bit data, and 64-bit data. Values larger than 32 bits, such as 40-bit-long or 64-bit-long values are stored in
register pairs, with the 32 LSBs of data placed in an even register and the remaining 8 or 32 MSBs in the
next upper register (which is always an odd-numbered register).
The eight functional units (.M1, .L1, .D1, .S1, .M2, .L2, .D2, and .S2) are each capable of executing one
instruction every clock cycle. The .M functional units perform all multiply operations. The .S and .L units
perform a general set of arithmetic, logical, and branch functions. The .D units primarily load data from
memory to the register file and store results from the register file into memory.
The C674x CPU combines the performance of the C64x+ core with the floating-point capabilities of the
C67x+ core.
Each C674x .M unit can perform one of the following each clock cycle: one 32 x 32 bit multiply, one 16 x
32 bit multiply, two 16 x 16 bit multiplies, two 16 x 32 bit multiplies, two 16 x 16 bit multiplies with
add/subtract capabilities, four 8 x 8 bit multiplies, four 8 x 8 bit multiplies with add operations, and four 16
x 16 multiplies with add/subtract capabilities (including a complex multiply). There is also support for
Galois field multiplication for 8-bit and 32-bit data. Many communications algorithms such as FFTs and
modems require complex multiplication. The complex multiply (CMPY) instruction takes four 16-bit inputs
and produces a 32-bit real and a 32-bit imaginary output. There are also complex multiplies with rounding
capability that produces one 32-bit packed output that contain 16-bit real and 16-bit imaginary values. The
32 x 32 bit multiply instructions provide the extended precision necessary for high-precision algorithms on
a variety of signed and unsigned 32-bit data types.
The .L or (Arithmetic Logic Unit) now incorporates the ability to do parallel add/subtract operations on a
pair of common inputs. Versions of this instruction exist to work on 32-bit data or on pairs of 16-bit data
performing dual 16-bit add and subtracts in parallel. There are also saturated forms of these instructions.
The C674x core enhances the .S unit in several ways. On the previous cores, dual 16-bit MIN2 and MAX2
comparisons were only available on the .L units. On the C674x core they are also available on the .S unit
which increases the performance of algorithms that do searching and sorting. Finally, to increase data
packing and unpacking throughput, the .S unit allows sustained high performance for the quad 8-bit/16-bit
and dual 16-bit instructions. Unpack instructions prepare 8-bit data for parallel 16-bit operations. Pack
instructions return parallel results to output precision including saturation support.
Other new features include:
• SPLOOP - A small instruction buffer in the CPU that aids in creation of software pipelining loops where
multiple iterations of a loop are executed in parallel. The SPLOOP buffer reduces the code size
associated with software pipelining. Furthermore, loops in the SPLOOP buffer are fully interruptible.
• Compact Instructions - The native instruction size for the C6000 devices is 32 bits. Many common
instructions such as MPY, AND, OR, ADD, and SUB can be expressed as 16 bits if the C674x
compiler can restrict the code to use certain registers in the register file. This compression is
performed by the code generation tools.
• Instruction Set Enhancement - As noted above, there are new instructions such as 32-bit
multiplications, complex multiplications, packing, sorting, bit manipulation, and 32-bit Galois field
multiplication.
• Exceptions Handling - Intended to aid the programmer in isolating bugs. The C674x CPU is able to
detect and respond to exceptions, both from internally detected sources (such as illegal op-codes) and
from system events (such as a watchdog time expiration).
• Privilege - Defines user and supervisor modes of operation, allowing the operating system to give a
basic level of protection to sensitive resources. Local memory is divided into multiple pages, each with
read, write, and execute permissions.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Overview
17
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
•
www.ti.com
Time-Stamp Counter - Primarily targeted for Real-Time Operating System (RTOS) robustness, a freerunning time-stamp counter is implemented in the CPU which is not sensitive to system stalls.
For more details on the C674x CPU and its enhancements over the C64x architecture, see the following
documents:
• TMS320C674x DSP CPU and Instruction Set Reference Guide (Literature Number: SPRUFE8)
• TMS320C674x DSP Megamodule Reference Guide (Literature Number: SPRUFK5)
18
Device Overview
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
src1
.L1
Odd
register
file A
(A1, A3,
A5...A31)
src2
odd dst
(D)
even dst
long src
Even
register
file A
(A0, A2,
A4...A30)
8
32 MSB
ST1b
32 LSB
ST1a
long src
8
even dst
.S1 odd dst
src1
Data path A
(D)
src2
.M1
dst2
dst1
src1
32
32
(A)
(B)
src2
(C)
32 MSB
LD1b
32 LSB
LD1a
dst
DA1
.D1
src1
src2
2x
1x
DA2
.D2
LD2a
LD2b
Odd
register
file B
(B1, B3,
B5...B31)
src2
src1
dst
Even
register
file B
(B0, B2,
B4...B30)
32 LSB
32 MSB
src2
.M2
(C)
src1
dst2
32
dst1
32
(B)
(A)
src2
src1
.S2
Data path B
ST2a
ST2b
odd dst
even dst
long src
(D)
8
32 MSB
32 LSB
long src
even dst
.L2
odd dst
8
(D)
src2
src1
Control Register
A.
B
C.
D.
.M unit, dst2 is 32 MSB.
On .M unit, dst1 is 32 LSB.
On C64x CPU .M unit, src2 is 32 bits; on C64x+ CPU .M unit, src2 is 64 bits.
On .L and .S units, odd dst connects to odd register files and even dst connects to even register files
Figure 2-3. TMS320C674x CPU (DSP Core) Data Paths
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Overview
19
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
2.6
www.ti.com
System Memory Management Unit (MMU)
All C674x accesses through its MDMA port will be directed through the system MMU module where they
are remapped to physical system addresses. This protects the ARM Cortex-A8 memory regions from
accidental corruption by C674x code and allows for direct allocation of buffers in user space without the
need for translation between ARM and DSP applications.
In addition, accesses by the EDMA TC0 and TC1 may optionally be routed through the system MMU. This
allows EDMA Channels 0 and 1 to be used by the DSP to perform transfers using only the known virtual
addresses of the associated buffers. The MMU_CFG register in the Control Module is used to
enable/disable use of the system MMU by the EDMA TCs.
For more details on the system MMU features, see the system MMU section of the Chip Level Resources
chapter in the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature
Number: SPRUGZ8).
20
Device Overview
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
2.7
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Media Controller Overview
The Media Controller has the responsibility of managing the HDVPSS, HDVICP2, and ISS modules.
For more details on the Media Controller, see the Media Controller Subsystem section of the Chip Level
Resources chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual
(Literature Number: SPRUGZ8).
2.8
HDVICP2 Overview
The HDVICP2 is a Video Encoder/Decoder hardware accelerator supporting a range of encode, decode,
and transcode operations for most major video codec standards. The main video Codec standards
supported in hardware are MPEG1/2/4 ASP/SP, H.264 BL/MP/HP, VC-1 SP/MP/AP, RV9/10, AVS-1.0,
and ON2 VP6.2/VP7.
The HDVICP2 hardware accelerator is composed of the following elements:
• Motion estimation acceleration engine
• Loop filter acceleration engine
• Sequencer, including its memories and an interrupt controller
• Intra-prediction estimation engine
• Calculation engine
• Motion compensation engine
• Entropy coder/decoder
• Video Direct Memory Access (DMA)
• Synchronization boxes
• Shared L2 controller
• Local interconnect
For more details on the HDVICP2, see the HD Video Coprocessor SubSystem section of the Chip Level
Resources chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual
(Literature Number: SPRUGZ8).
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Overview
21
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
2.9
www.ti.com
SGX530 Overview
The SGX530 is a vector/3D graphics accelerator for vector and 3-dimensional (3D) graphics applications.
The SGX530 graphics accelerator efficiently processes a number of various multimedia data types
concurrently:
• Pixel data
• Vertex data
• Video data
This is achieved using a multi-threaded architecture using two levels of scheduling and data partitioning
enabling zero overhead task switching.
The SGX530 has the following major features:
• Vector graphics and 3D graphics
• Tile-based architecture
• Universal Scalable Shader Engine (USSE™) - multi-threaded engine incorporating pixel and vertex
shader functionality
• Advanced shader feature set - in excess of Microsoft VS3.0, PS3.0, and OpenGL2.0
• Industry standard API support - OpenGL ES 1.1 and 2.0, OpenVG v1.1
• Fine-grained task switching, load balancing, and power management
• Advanced geometry DMA driven operation for minimum CPU interaction
• Programmable high-quality image anti-aliasing
• POWERVR® SGX core MMU for address translation from the core virtual address to the external
physical address (up to 4GB address range)
• Fully-virtualized memory addressing for OS operation in a unified memory architecture
• Advanced and standard 2D operations [for example, vector graphics, block level transfers (BLTs),
raster operations (ROPs)]
For more details on the SGX530, see the Chip Level Resources chapter of the TMS320DM814x DaVinci
Digital Media Processors Technical Reference Manual (Literature Number: SPRUGZ8).
2.10 Spinlock Module Overview
The Spinlock module provides hardware assistance for synchronizing the processes running on multiple
processors in the device:
• ARM Cortex-A8 processor
• C674x DSP
• Media Controller
The Spinlock module implements 128 spinlocks (or hardware semaphores) that provide an efficient way to
perform a lock operation of a device resource using a single read-access, avoiding the need for a readmodify-write bus transfer of which the programmable cores are not capable.
For more details on the Spinlock Module, see the Spinlock section of the Chip Level Resources chapter of
the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
22
Device Overview
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
2.11 Mailbox Module Overview
The device Mailbox module facilitates communication between the ARM Cortex-A8, C674x DSP, and the
Media Controller. The device mailbox consists of twelve mailboxes, each supporting a 1-way
communication between two of the above processors. The sender sends information to the receiver by
writing a message to the mailbox registers. Interrupt signaling is used to notify the receiver that a message
has been queued or to notify the sender about an overflow situation.
The Mailbox module supports the following features (see Figure 2-4):
• 12 mailboxes
• Flexible mailbox-to-processor assignment scheme
• Four-message FIFO depth for each message queue
• 32-bit message width
• Message reception and queue-not-full notification using interrupts
• Four interrupts (one to ARM Cortex-A8, one to C674x, and two to Media Controller)
Mailbox Module
Mailbox
Mailbox
Mailbox
Mailbox
Mailbox
Mailbox
Mailbox
Mailbox
Mailbox
Mailbox
Mailbox
Mailbox
L4
Interconnect
Interrupt
ARM Cortex-A8
Interrupt
C674x+ DSP
Interrupt
Interrupt
Media Controller
Figure 2-4. Mailbox Module Block Diagram
For more details on the Mailbox Module, see the Mailbox section of the Chip Level Resources chapter of
the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Overview
23
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
2.12 Memory Map Summary
The device has multiple on-chip memories associated with its two processors and various subsystems. To
help simplify software development a unified memory map is used where possible to maintain a consistent
view of device resources across all bus masters.
2.12.1 L3 Memory Map
Table 2-3 shows the L3 memory map for all system masters (including Cortex-A8). Table 2-3 and Table 26 show the memory map of the C674x DSP which has limited access to the following peripherals:
McASPx, McBSP, UARTx, I2Cx, SPIx, EDMA, GPIO/INT, GPMC, DDRx, EMAC, PCIe, Timers, and USB.
Table 2-4 shows the memory map for the C674x DSP.
For more details on the interconnect topology and connectivity across the L3 and L4 interconnects, see
Table 7-17, System Interconnect.
Table 2-3. L3 Memory Map
START ADDRESS
(HEX)
24
END ADDRESS
(HEX)
SIZE
DESCRIPTION
0x0000_0000
0x00FF_FFFF
16MB
GPMC (Reserved for BOOTROM)
0x0100_0000
0x1FFF_FFFF
496MB
GPMC
0x2000_0000
0x2FFF_FFFF
256MB
PCIe
0x3000_0000
0x3FFF_FFFF
256MB
Reserved
0x4000_0000
0x4001_FFFF
128KB
Reserved
0x4002_0000
0x4002_BFFF
48KB
ARM Cortex-A8 ROM
(Accessible by ARM Cortex-A8 only)
0x4002_C000
0x402E_FFFF
2832KB
Reserved
0x402F_0000
0x402F_03FF
1KB
Reserved
0x402F_0400
0x402F_FFFF
64KB - 1KB
0x4030_0000
0x4031_FFFF
128KB
OCMC SRAM
0x4032_0000
0x407F_FFFF
4992KB
Reserved
0x4080_0000
0x4083_FFFF
256KB
C674x™ L2 RAM
0x4084_0000
0x40DF_FFFF
5888KB
Reserved
0x40E0_0000
0x40E0_7FFF
32KB
C674x L1P Cache/RAM
0x40E0_8000
0x40EF_FFFF
992KB
Reserved
0x40F0_0000
0x40F0_7FFF
32KB
C674x L1D Cache/RAM
0x40F0_8000
0x40FF_FFFF
992KB
Reserved
0x4100_0000
0x41FF_FFFF
16MB
Reserved
0x4200_0000
0x43FF_FFFF
32MB
Reserved
0x4400_0000
0x443F_FFFF
4MB
L3 Fast configuration registers
0x4440_0000
0x447F_FFFF
4MB
L3 Mid configuration registers
0x4480_0000
0x44BF_FFFF
4MB
L3 Slow configuration registers
0x44C0_0000
0x45FF_FFFF
20MB
Reserved
0x4600_0000
0x463F_FFFF
4MB
McASP0 Data Peripheral Registers
0x4640_0000
0x467F_FFFF
4MB
McASP1 Data Peripheral Registers
0x4680_0000
0x46BF_FFFF
4MB
McASP2 Data Peripheral Registers
0x46C0_0000
0x46FF_FFFF
4MB
HDMI
0x4700_0000
0x473F_FFFF
4MB
McBSP
0x4740_0000
0x477F_FFFF
4MB
USB
0x4780_0000
0x4780_FFFF
64KB
Reserved
MMC/SD/SDIO2 Peripheral Registers
0x4781_0000
0x4781_1FFF
8KB
0x4781_2000
0x47BF_FFFF
4MB - 72KB
Device Overview
ARM Cortex-A8 RAM
(Accessible by ARM Cortex-A8 only)
Reserved
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 2-3. L3 Memory Map (continued)
START ADDRESS
(HEX)
END ADDRESS
(HEX)
SIZE
DESCRIPTION
0x47C0_0000
0x47C0_BFFF
48KB
Reserved
0x47C0_C000
0x47C0_C3FF
1KB
Reserved
0x47C0_C400
0x47C0_C7FF
1KB
DDR0 PHY Registers
0x47C0_C800
0x47C0_CBFF
1KB
DDR1 PHY Registers
0x47C0_CC00
0x47C0_CFFF
1KB
Reserved
0x47C0_D000
0x47FF FFFF
4044KB
Reserved
0x4800_0000
0x48FF_FFFF
16MB
L4 Slow Peripheral Domain
(see Table 2-7)
0x4900_0000
0x490F_FFFF
1MB
EDMA TPCC Registers
0x4910_0000
0x497F_FFFF
7MB
Reserved
0x4980_0000
0x498F_FFFF
1MB
EDMA TPTC0 Registers
0x4990_0000
0x499F_FFFF
1MB
EDMA TPTC1 Registers
0x49A0_0000
0x49AF_FFFF
1MB
EDMA TPTC2 Registers
0x49B0_0000
0x49BF_FFFF
1MB
EDMA TPTC3 Registers
0x49C0_0000
0x49FF_FFFF
4MB
Reserved
0x4A00_0000
0x4AFF_FFFF
16MB
L4 Fast Peripheral Domain
(see Table 2-6)
0x4B00_0000
0x4BFF_FFFF
16MB
Emulation Subsystem
0x4C00_0000
0x4CFF_FFFF
16MB
DDR0 Registers
0x4D00_0000
0x4DFF_FFFF
16MB
DDR1 Registers
0x4E00_0000
0x4FFF_FFFF
32MB
DDR DMM Registers
0x5000_0000
0x50FF_FFFF
16MB
GPMC Registers
0x5100_0000
0x51FF_FFFF
16MB
PCIE Registers
0x5200_0000
0x54FF_FFFF
48MB
Reserved
0x5500_0000
0x55FF_FFFF
16MB
Media Controller
0x5600_0000
0x56FF_FFFF
16MB
SGX530
0x5700_0000
0x57FF_FFFF
16MB
Reserved
0x5800_0000
0x58FF_FFFF
16MB
HDVICP2 Configuration
0x5900_0000
0x59FF_FFFF
16MB
HDVICP2 SL2
0x5A00_0000
0x5BFF_FFFF
32MB
Reserved
0x5C00_0000
0x5DFF_FFFF
32MB
ISS
0x5E00_0000
0x5FFF_FFFF
32MB
Reserved
0x6000_0000
0x7FFF_FFFF
512MB
DDR DMM TILER Window (see Table 2-8)
0x8000_0000
0xFFFF_FFFF
2GB
DDR
0x1 0000 0000
0x1 FFFF FFFF
4GB
DDR DMM TILER Extended Address Map
(ISS and HDVPSS only) [see Table 2-8]
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Overview
25
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
2.12.2 C674x Memory Map
Table 2-4 shows the memory map for the C674x DSP.
Table 2-4. C674x Memory Map
(1)
(2)
26
START ADDRESS
(HEX)
END ADDRESS
(HEX)
SIZE
0x0000_0000
0x003F_FFFF
4MB
DESCRIPTION
Reserved
0x0040_0000
0x0043_FFFF
256KB
HDVICP2 SL2
0x0044_0000
0x007F_FFFF
3840KB
Reserved
0x0080_0000
0x0083_FFFF
256KB
C674x™ L2 RAM
Reserved
0x0084_0000
0x00DF_FFFF
5888KB
0x00E0_0000
0x00E0_7FFF
32KB
C674x L1P Cache/RAM
0x00E0_8000
0x00EF_FFFF
992KB
Reserved
0x00F0_0000
0x00F0_7FFF
32KB
C674x L1D Cache/RAM
0x00F0_8000
0x017F_FFFF
9184KB
0x0180_0000
0x01BF_FFFF
4MB
0x01C0_0000
0x07FF_FFFF
100MB
Reserved
0x0800_0000
0x08FF_FFFF
16MB
L4 Slow Peripheral Domain
(see Table 2-7)
0x0900_0000
0x090F_FFFF
1MB
EDMA TPCC Registers
0x0910_0000
0x097F_FFFF
7MB
Reserved
0x0980_0000
0x098F_FFFF
1MB
EDMA TPTC0 Registers
0x0990_0000
0x099F_FFFF
1MB
EDMA TPTC1 Registers
0x09A0_0000
0x09AF_FFFF
1MB
EDMA TPTC2 Registers
Reserved
C674x Internal CFG registers
0x09B0_0000
0x09BF_FFFF
1MB
EDMA TPTC3 Registers
0x09C0_0000
0x09FF_FFFF
4MB
Reserved
0x0A00_0000
0x0AFF_FFFF
16MB
L4 Fast Peripheral Domain
(see Table 2-6)
0x0B00_0000
0x0FFF_FFFF
80MB
Reserved
0x1000_0000
0x10FF_FFFF
16MB
C674x Internal Global Address (1)
0x1100_0000
0xFFFF_FFFF
3824MB
System MMU Mapped L3
Regions (2)
Addresses 0x1000_0000 to 0x10FF_FFFF are mapped to C674x internal addresses 0x0000_0000 to 0x00FF_FFFF.
For more details on the system MMU features, see the System MMU section of the Chip Level Resources chapter in the
TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number: SPRUGZ8).
Device Overview
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
2.12.3 C674x Memory Map (Memory Management Unit Bypassed)
Table 2-5 shows the memory map for the C674x DSP when bypassing the Memory Management Unit.
Table 2-5. MMU Bypassed C674x DSP Memory Map
(1)
START ADDRESS
(HEX)
END ADDRESS
(HEX)
0x0000_0000
0x007F_FFFF
SIZE
DESCRIPTION
Reserved
0x0080_0000
0x0083_FFFF
0x0084_0000
0x00DF_FFFF
256KB
C674x™ Level 2 (L2) Cache / RAM
0x00E0_0000
0x00E0_7FFF
0x00E0_8000
0x00EF_FFFF
0x00F0_0000
0x00F0_7FFF
0x00F0_8000
0x017F_FFFF
0x0180_0000
0x01BF_FFFF
0x01C0_0000
0x07FF_FFFF
0x0800_0000
0x083F_FFFF
4MB
L4 Slow0 Peripheral Domain
(see )
0x0840_0000
0x08FF_FFFF
12MB
L4 Slow1 Peripheral Domain
(see )
0x0900_0000
0x090F_FFFF
1MB
EDMA Channel Controller 0 Configuration Registers
0x0910_0000
0x097F_FFFF
0x0980_0000
0x098F_FFFF
1MB
EDMA Transfer Controller 0 Configuration Registers
0x0990_0000
0x099F_FFFF
1MB
EDMA Transfer Controller 1 Configuration Registers
0x09A0_0000
0x09AF_FFFF
1MB
EDMA Transfer Controller 2 Configuration Registers
1MB
EDMA Transfer Controller 3 Configuration Registers
Reserved
32KB
C674x Level 1 Program (L1P) Cache/RAM
Reserved
32KB
C674x Level 1 Data (L1D) Cache and RAM
Reserved
4MB
C674x Interrupt Controller and Configuration Registers
Reserved
Reserved
0x09B0_0000
0x09BF_FFFF
0x09C0_0000
0x09FF_FFFF
0x0A00_0000
0x0AFF_FFFF
0x0B00_0000
0x0FFF_FFFF
0x1000_0000
0x10FF_FFFF
16MB
C674x Internal Global Address (1)
0x1100_0000
0x1FFF+FFFF
240MB
GPMC Slave Address Space
0x2000_0000
0x2FFF_FFFF
256MB
PCI Express (PCI-e) Slave Port
0x3000_0000
0x3FFF_FFFF
Reserved
0x4002_0000
0x400F_FFFF
Reserved (BOOTROM)
0x4010_0000
0x402F_FFFF
0x4030_0000
0x4033_FFFF
0x4034_0000
0x43FF_FFFF
0x4400_0000
0x443F_FFFF
4MB
Level 3 Fast (L3F) Interconnect Configuration Registers
0x4440_0000
0x447F_FFFF
4MB
Level 3 Mid (L3M) Interconnect Configuration Registers
0x4480_0000
0x44BF_FFFF
4MB
Level 3 Slow (L3S) Interconnect Configuration Registers
0x44C0_0000
0x44FF_FFFF
0x4500_0000
0x45FF_FFFF
16MB
Expansion L3 port
0x4600_0000
0x463F_FFFF
4MB
McASP0 Data Port
0x4640_0000
0x467F_FFFF
4MB
McASP1 Data Port
4MB
McASP2 Data Port
Reserved
16MB
L4 Fast Peripheral Domain
(see Table 2-6)
Reserved
Reserved
256KB
On Chip Level 3 (L3) RAM
Reserved
Reserved
0x4680_0000
0x46BF_FFFF
0x46C0_0000
0x46FF_FFFF
0x4700_0000
0x473F_FFFF
4MB
McBSP Peripheral Configuration Registers
0x4740_0000
0x477F_FFFF
4MB
USB Subsystem Configuration Registers
0x4780_0000
0x4780_FFFF
64KB
Viterbi Coprocessor 2 Configuration Registers
Reserved
Addresses 0x1000_0000 to 0x10FF_FFFF are mapped to C674x internal addresses 0x0000_0000 to 0x00FF_FFFF.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Overview
27
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 2-5. MMU Bypassed C674x DSP Memory Map (continued)
START ADDRESS
(HEX)
(2)
28
END ADDRESS
(HEX)
SIZE
0x4781_0000
0x4781_1FFF
8KB
0x4781_2000
0x47FF_FFFF
0x4800_0000
0x483F_FFFF
4MB
L4 Slow0 Peripheral Domain
(see )
0x4840_0000
0x48FF_FFFF
12MB
L4 Slow1 Peripheral Domain
(see )
0x4900_0000
0x490F_FFFF
1MB
EDMA Channel Controller Registers
0x4910_0000
0x497F_FFFF
0x4980_0000
0x498F_FFFF
1MB
EDMA Transfer Controller 0 Registers
0x4990_0000
0x499F_FFFF
1MB
EDMA Transfer Controller 1 Registers
0x49A0_0000
0x49AF_FFFF
1MB
EDMA Transfer Controller 2 Registers
0x49B0_0000
0x49BF_FFFF
1MB
EDMA Transfer Controller 3 Registers
0x49C0_0000
0x49FF_FFFF
0x4A00_0000
0x4AFF_FFFF
16MB
L4 Fast Peripheral Domain
(see Table 2-6)
DESCRIPTION
MMC/SD2 Peripheral Configuration Registers
Reserved
Reserved
Reserved
0x4B00_0000
0x4BFF_FFFF
16MB
Emulation Subsystem
0x4C00_0000
0x4CFF_FFFF
16MB
DDR Configuration Registers
0x4D00_0000
0x4FFF_FFFF
0x5000_0000
0x50FF_FFFF
16MB
General Purpose Memory Controller Configuration Registers
0x5100_0000
0x51FF_FFFF
16MB
PCI Express (PCIe) Peripheral Configuration Registers
0x5200_0000
0x523F_FFFF
0x5240_0000
0x527F_FFFF
0x5280_0000
0x54BF_FFFF
0x54C0_0000
0x54FF_FFFF
4MB
Analog-to-Digital Converter / Touchscreen Controller DMA
Port Registers
0x5500_0000
0x55FF_FFFF
16MB
Media Controller Registers (2)
0x5600_0000
0x56FF_FFFF
16MB
SGX530 3D Graphics Engine Configuration Registers
0x5700_0000
0x7FFF_FFFF
0x8000_0000
0xFFFF_FFFF
Reserved
Reserved
4MB
BitBLT 2D Graphics Engine Configuration Registers
Reserved
Reserved
2GB
DDR Addressable Memory Space
This range maps into the 0x5500 0000 - 0x55FF FFFF region of )
Device Overview
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
2.12.4 L4 Memory Map
The L4 Fast Peripheral Domain, L4 Slow Peripheral Domain regions of the memory maps above are
broken out into Table 2-6 and Table 2-7.
For more details on the interconnect topology and connectivity across the L3 and L4 interconnects, see
Table 7-17, System Interconnect.
2.12.4.1 L4 Fast Peripheral Memory Map
Table 2-6. L4 Fast Peripheral Memory Map
Cortex-A8 and L3 Masters
C674x DSP
START
ADDRESS
(HEX)
END ADDRESS
(HEX)
START
ADDRESS
(HEX)
END ADDRESS
(HEX)
SIZE
0x4A00_0000
0x4A00_07FF
0x0A00_0000
0x0A00_07FF
2KB
L4 Fast Configuration - Address/Protection
(AP)
0x4A00_0800
0x4A00_0FFF
0x0A00_0800
0x0A00_0FFF
2KB
L4 Fast Configuration - Link Agent (LA)
0x4A00_1000
0x4A00_13FF
0x0A00_1000
0x0A00_13FF
1KB
L4 Fast Configuration - Initiator Port (IP0)
0x4A00_1400
0x4A00_17FF
0x0A00_1400
0x0A00_17FF
1KB
L4 Fast Configuration - Initiator Port (IP1)
0x4A00_1800
0x4A00_1FFF
0x0A00_1800
0x0A00_1FFF
2KB
Reserved
0x4A00_2000
0x4A07_FFFF
0x0A00_2000
0x0A07_FFFF
504KB
Reserved
0x4A08_0000
0x4A0F_FFFF
0x0A08_0000
0x0A0F_FFFF
512KB
Reserved
0x4A10_0000
0x4A10_7FFF
0x0A10_0000
0x0A10_7FFF
32KB
EMAC SW Peripheral Registers
0x4A10_8000
0x4A10_8FFF
0x0A10_8000
0x0A10_8FFF
4KB
EMAC SW Support Registers
0x4A14_0000
0x4A14_FFFF
64KB
SATA Peripheral Registers
4KB
SATA Support Registers
DEVICE NAME
0x4A15_0000
0x4A15_0FFF
0x4A15_1000
0x4A17_FFFF
0x0A15_1000
0x0A17_FFFF
188KB
Reserved
0x4A18_0000
0x4A1A_1FFF
0x0A18_0000
0x0A1A_1FFF
136KB
Reserved
0x4A1A_2000
0x4A1A_3FFF
0x0A1A_2000
0x0A1A_3FFF
8KB
McASP3 Configuration Peripheral Registers
0x4A1A_4000
0x4A1A_4FFF
0x0A1A_4000
0x0A1A_4FFF
4KB
McASP3 Configuration Support Registers
0x4A1A_5000
0x4A1A_5FFF
0x0A1A_5000
0x0A1A_5FFF
4KB
McASP3 Data Peripheral Registers
0x4A1A_6000
0x4A1A_6FFF
0x0A1A_6000
0x0A1A_6FFF
4KB
McASP3 Data Support Registers
0x4A1A_7000
0x4A1A_7FFF
0x0A1A_7000
0x0A1A_7FFF
4KB
Reserved
0x4A1A_8000
0x4A1A_9FFF
0x0A1A_8000
0x0A1A_9FFF
8KB
McASP4 Configuration Peripheral Registers
0x4A1A_A000
0x4A1A_AFFF
0x0A1A_A000
0x0A1A_AFFF
4KB
McASP4 Configuration Support Registers
0x4A1A_B000
0x4A1A_BFFF
0x0A1A_B000
0x0A1A_BFFF
4KB
McASP4 Data Peripheral Registers
0x4A1A_C000
0x4A1A_CFFF
0x0A1A_C000
0x0A1A_CFFF
4KB
McASP4 Data Support Registers
0x4A1A_D000
0x4A1A_DFFF
0x0A1A_D000
0x0A1A_DFFF
4KB
Reserved
0x4A1A_E000
0x4A1A_FFFF
0x0A1A_E000
0x0A1A_FFFF
8KB
McASP5 Configuration Peripheral Registers
0x4A1B_0000
0x4A1B_0FFF
0x0A1B_0000
0x0A1B_0FFF
4KB
McASP5 Configuration Support Registers
0x4A1B_1000
0x4A1B_1FFF
0x0A1B_1000
0x0A1B_1FFF
4KB
McASP5 Data Peripheral Registers
0x4A1B_2000
0x4A1B_2FFF
0x0A1B_2000
0x0A1B_2FFF
4KB
McASP5 Data Support Registers
0x4A1B_3000
0x4A1B_5FFF
0x0A1B_3000
0x0A1B_5FFF
12KB
Reserved
0x4A1B_6000
0x4A1B_6FFF
0x0A1B_6000
0x0A1B_6FFF
4KB
Reserved
0x4A1B_4000
0x4AFF_FFFF
0x0A1B_4000
0x0AFF_FFFF
14632KB
Reserved
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Overview
29
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
2.12.4.2 L4 Slow Peripheral Memory Map
Table 2-7. L4 Slow Peripheral Memory Map
Cortex-A8 and L3 Masters
30
C674x DSP
START
ADDRESS
(HEX)
END ADDRESS
(HEX)
START
ADDRESS (HEX)
END ADDRESS
(HEX)
SIZE
0x4800_0000
0x4800_07FF
0x0800_0000
0x0800_07FF
2KB
L4 Slow Configuration –
Address/Protection (AP)
0x4800_0800
0x4800_0FFF
0x0800_0800
0x0800_0FFF
2KB
L4 Slow Configuration – Link Agent
(LA)
0x4800_1000
0x4800_13FF
0x0800_1000
0x0800_13FF
1KB
L4 Slow Configuration – Initiator Port
(IP0)
0x4800_1400
0x4800_17FF
0x0800_1400
0x0800_17FF
1KB
L4 Slow Configuration – Initiator Port
(IP1)
0x4800_1800
0x4800_1FFF
0x0800_1800
0x0800_1FFF
2KB
Reserved
0x4800_2000
0x4800_7FFF
0x0800_2000
0x0800_7FFF
24KB
Reserved
0x4800_8000
0x4800_8FFF
0x0800_8000
0x0800_8FFF
32KB
Reserved
0x4801_0000
0x4801_0FFF
0x0801_0000
0x0801_0FFF
4KB
System MMU Peripheral Registers
0x4801_1000
0x4801_1FFF
0x0801_1000
0x0801_1FFF
4KB
System MMU Support Registers
0x4801_2000
0x4801_FFFF
0x0801_2000
0x0801_FFFF
56KB
Reserved
0x4802_0000
0x4802_0FFF
0x0802_0000
0x0802_0FFF
4KB
UART0 Peripheral Registers
0x4802_1000
0x4802_1FFF
0x0802_1000
0x0802_1FFF
4KB
UART0 Support Registers
0x4802_2000
0x4802_2FFF
0x0802_2000
0x0802_2FFF
4KB
UART1 Peripheral Registers
0x4802_3000
0x4802_3FFF
0x0802_3000
0x0802_3FFF
4KB
UART1 Support Registers
0x4802_4000
0x4802_4FFF
0x0802_4000
0x0802_4FFF
4KB
UART2 Peripheral Registers
0x4802_5000
0x4802_5FFF
0x0802_5000
0x0802_5FFF
4KB
UART2 Support Registers
0x4802_6000
0x4802_7FFF
0x0802_6000
0x0802_7FFF
8KB
Reserved
0x4802_8000
0x4802_8FFF
0x0802_8000
0x0802_8FFF
4KB
I2C0 Peripheral Registers
0x4802_9000
0x4802_9FFF
0x0802_9000
0x0802_9FFF
4KB
I2C0 Support Registers
0x4802_A000
0x4802_AFFF
0x0802_A000
0x0802_AFFF
4KB
I2C1 Peripheral Registers
DEVICE NAME
0x4802_B000
0x4802_BFFF
0x0802_B000
0x0802_BFFF
4KB
I2C1 Support Registers
0x4802_C000
0x4802_DFFF
0x0802_C000
0x0802_DFFF
8KB
Reserved
0x4802_E000
0x4802_EFFF
0x0802_E000
0x0802_EFFF
4KB
TIMER1 Peripheral Registers
0x4802_F000
0x4802_FFFF
0x0802_F000
0x0802_FFFF
4KB
TIMER1 Support Registers
0x4803_0000
0x4803_0FFF
0x0803_0000
0x0803_0FFF
4KB
SPI0 Peripheral Registers
0x4803_1000
0x4803_1FFF
0x0803_1000
0x0803_1FFF
4KB
SPI0 Support Registers
0x4803_2000
0x4803_2FFF
0x0803_2000
0x0803_2FFF
4KB
GPIO0 Peripheral Registers
0x4803_3000
0x4803_3FFF
0x0803_3000
0x0803_3FFF
4KB
GPIO0 Support Registers
0x4803_4000
0x4803_7FFF
0x0803_4000
0x0803_7FFF
16KB
Reserved
0x4803_8000
0x4803_9FFF
0x0803_8000
0x0803_9FFF
8KB
McASP0 CFG Peripheral Registers
0x4803_A000
0x4803_AFFF
0x0803_A000
0x0803_AFFF
4KB
McASP0 CFG Support Registers
0x4803_B000
0x4803_BFFF
0x0803_B000
0x0803_BFFF
4KB
Reserved
0x4803_C000
0x4803_DFFF
0x0803_C000
0x0803_DFFF
8KB
McASP1 CFG Peripheral Registers
0x4803_E000
0x4803_EFFF
0x0803_E000
0x0803_EFFF
4KB
McASP1 CFG Support Registers
0x4803_F000
0x4803_FFFF
0x0803_F000
0x0803_FFFF
4KB
Reserved
0x4804_0000
0x4804_0FFF
0x0804_0000
0x0804_0FFF
4KB
TIMER2 Peripheral Registers
0x4804_1000
0x4804_1FFF
0x0804_1000
0x0804_1FFF
4KB
TIMER2 Support Registers
0x4804_2000
0x4804_2FFF
0x0804_2000
0x0804_2FFF
4KB
TIMER3 Peripheral Registers
0x4804_3000
0x4804_3FFF
0x0804_3000
0x0804_3FFF
4KB
TIMER3 Support Registers
0x4804_4000
0x4804_4FFF
0x0804_4000
0x0804_4FFF
4KB
TIMER4 Peripheral Registers
Device Overview
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 2-7. L4 Slow Peripheral Memory Map (continued)
Cortex-A8 and L3 Masters
C674x DSP
START
ADDRESS
(HEX)
END ADDRESS
(HEX)
START
ADDRESS (HEX)
END ADDRESS
(HEX)
SIZE
0x4804_5000
0x4804_5FFF
0x0804_5000
0x0804_5FFF
4KB
TIMER4 Support Registers
0x4804_6000
0x4804_6FFF
0x0804_6000
0x0804_6FFF
4KB
TIMER5 Peripheral Registers
0x4804_7000
0x4804_7FFF
0x0804_7000
0x0804_7FFF
4KB
TIMER5 Support Registers
0x4804_8000
0x4804_8FFF
0x0804_8000
0x0804_8FFF
4KB
TIMER6 Peripheral Registers
0x4804_9000
0x4804_9FFF
0x0804_9000
0x0804_9FFF
4KB
TIMER6 Support Registers
0x4804_A000
0x4804_AFFF
0x0804_A000
0x0804_AFFF
4KB
TIMER7 Peripheral Registers
0x4804_B000
0x4804_BFFF
0x0804_B000
0x0804_BFFF
4KB
TIMER7 Support Registers
0x4804_C000
0x4804_CFFF
0x0804_C000
0x0804_CFFF
4KB
GPIO1 Peripheral Registers
0x4804_D000
0x4804_DFFF
0x0804_D000
0x0804_DFFF
4KB
GPIO1 Support Registers
0x4804_E000
0x4804_FFFF
0x0804_E000
0x0804_FFFF
8KB
Reserved
0x4805_0000
0x4805_1FFF
0x0805_0000
0x0805_1FFF
8KB
McASP2 CFG Peripheral Registers
0x4805_2000
0x4805_2FFF
0x0805_2000
0x0805_2FFF
4KB
McASP2 CFG Support Registers
0x4805_3000
0x4805_FFFF
0x0805_3000
0x0805_FFFF
52KB
Reserved
0x4806_0000
0x4806_FFFF
64KB
MMC/SD/SDIO0 Peripheral Registers
0x4807_0000
0x4807_0FFF
4KB
MMC/SD/SDIO0 Support Registers
0x4807_1000
0x4807_FFFF
60KB
Reserved
0x4808_0000
0x4808_FFFF
64KB
ELM Peripheral Registers
0x4809_0000
0x4809_0FFF
4KB
ELM Support Registers
0x0807_1000
0x0807_FFFF
DEVICE NAME
0x4809_1000
0x4809_FFFF
0x0809_1000
0x0809_FFFF
60KB
Reserved
0x480A_0000
0x480A_FFFF
0x080A_0000
0x080A_FFFF
64KB
Reserved
0x480B_0000
0x480B_0FFF
0x080B_0000
0x080B_0FFF
4KB
Reserved
0x080B_1000
0x080B_FFFF
0x480B_1000
0x480B_FFFF
60KB
Reserved
0x480C_0000
0x480C_0FFF
4KB
RTC Peripheral Registers
0x480C_1000
0x480C_1FFF
4KB
RTC Support Registers
0x480C_2000
0x480C_3FFF
0x080C_2000
0x080C_3FFF
8KB
Reserved
0x480C_4000
0x480C_7FFF
0x080C_4000
0x080C_7FFF
16KB
Reserved
0x480C_8000
0x480C_8FFF
0x080C_8000
0x080C_8FFF
4KB
Mailbox Peripheral Registers
0x480C_9000
0x480C_9FFF
0x080C_9000
0x080C_9FFF
4KB
Mailbox Support Registers
0x480C_A000
0x480C_AFFF
0x080C_A000
0x080C_AFFF
4KB
Spinlock Peripheral Registers
0x480C_B000
0x480C_BFFF
0x080C_B000
0x080C_BFFF
4KB
Spinlock Support Registers
0x480C_C000
0x480F_FFFF
0x080C_C000
0x080F_FFFF
208KB
Reserved
0x4810_0000
0x4811_FFFF
128KB
HDVPSS Peripheral Registers
0x4812_0000
0x4812_0FFF
4KB
HDVPSS Support Registers
0x4812_1000
0x4812_1FFF
4KB
Reserved
0x4812_2000
0x4812_2FFF
4KB
HDMI Peripheral Registers
4KB
HDMI Support Registers
0x0812_1000
0x0812_1FFF
0x4812_3000
0x4812_3FFF
0x4812_4000
0x4813_FFFF
0x0812_4000
0x0813_FFFF
112KB
Reserved
0x4814_0000
0x4815_FFFF
0x0814_0000
0x0815_FFFF
128KB
Control Module Peripheral Registers
(C674x DSP Restricted to only
exposed peripherals)
0x4816_0000
0x4816_0FFF
0x0816_0000
0x0816_0FFF
4KB
0x4816_1000
0x4817_FFFF
0x0816_1000
0x0817_FFFF
124KB
Reserved
0x4818_0000
0x4818_2FFF
0x0818_0000
0x0818_2FFF
12KB
PRCM Peripheral Registers
(C674x DSP Restricted to only
exposed peripherals)
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Control Module Support Registers
(C674x DSP Restricted to only
exposed peripherals)
Device Overview
31
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 2-7. L4 Slow Peripheral Memory Map (continued)
Cortex-A8 and L3 Masters
32
C674x DSP
START
ADDRESS
(HEX)
END ADDRESS
(HEX)
START
ADDRESS (HEX)
END ADDRESS
(HEX)
SIZE
0x4818_3000
0x4818_3FFF
0x0818_3000
0x0818_3FFF
4KB
PRCM Support Registers
(C674x DSP Restricted to only
exposed peripherals)
DEVICE NAME
0x4818_4000
0x4818_7FFF
0x0818_4000
0x0818_7FFF
16KB
Reserved
0X4818_8000
0X4818_BFFF
0x0818_8000
0x0818_BFFF
16KB
Reserved
0x4818_C000
0x4818_CFFF
4KB
OCP Watchpoint Peripheral Registers
0x4818_D000
0x4818_DFFF
4KB
OCP Watchpoint Support Registers
0x4818_E000
0x4818_EFFF
0x0818_E000
0x0818_EFFF
4KB
Reserved
0x4818_F000
0x4818_FFFF
0x0818_F000
0x0818_FFFF
4KB
Reserved
0x4819_0000
0x4819_3FFF
0x0819_0000
0x0819_3FFF
16KB
Reserved
0x4819_4000
0x4819_BFFF
0x0819_4000
0x0819_BFFF
32KB
Reserved
0x4819_C000
0x481F_FFFF
0x0819_C000
0x081F_FFFF
400KB
Reserved
0x4819_C000
0x4819_CFFF
0x0819_C000
0x0819_CFFF
4KB
I2C2 Peripheral Registers
0x4819_D000
0x4819_DFFF
0x0819_D000
0x0819_DFFF
4KB
I2C2 Support Registers
0x4819_E000
0x4819_EFFF
0x0819_E000
0x0819_EFFF
4KB
I2C3 Peripheral Registers
0x4819_F000
0x4819_FFFF
0x0819_F000
0x0819_FFFF
4KB
I2C3 Support Registers
0x481A_0000
0x481A_0FFF
0x081A_0000
0x081A_0FFF
4KB
SPI1 Peripheral Registers
0x481A_1000
0x481A_1FFF
0x081A_1000
0x081A_1FFF
4KB
SPI1 Support Registers
0x481A_2000
0x481A_2FFF
0x081A_2000
0x081A_2FFF
4KB
SPI2 Peripheral Registers
0x481A_3000
0x481A_3FFF
0x081A_3000
0x081A_3FFF
4KB
SPI2 Support Registers
0x481A_4000
0x481A_4FFF
0x081A_4000
0x081A_4FFF
4KB
SPI3 Peripheral Registers
0x481A_5000
0x481A_5FFF
0x081A_5000
0x081A_5FFF
4KB
SPI3 Support Registers
0x481A_6000
0x481A_6FFF
0x081A_6000
0x081A_6FFF
4KB
UART3 Peripheral Registers
0x481A_7000
0x481A_7FFF
0x081A_7000
0x081A_7FFF
4KB
UART3 Support Registers
0x481A_8000
0x481A_8FFF
0x081A_8000
0x081A_8FFF
4KB
UART4 Peripheral Registers
0x481A_9000
0x481A_9FFF
0x081A_9000
0x081A_9FFF
4KB
UART4 Support Registers
0x481A_A000
0x481A_AFFF
0x081A_A000
0x081A_AFFF
4KB
UART5 Peripheral Registers
0x481A_B000
0x481A_BFFF
0x081A_B000
0x081A_BFFF
4KB
UART5 Support Registers
0x481A_C000
0x481A_CFFF
0x081A_C000
0x081A_CFFF
4KB
GPIO2 Peripheral Registers
0x481A_D000
0x481A_DFFF
0x081A_D000
0x081A_DFFF
4KB
GPIO2 Support Registers
0x481A_E000
0x481A_EFFF
0x081A_E000
0x081A_EFFF
4KB
GPIO3 Peripheral Registers
0x481A_F000
0x481A_FFFF
0x081A_F000
0x081A_FFFF
4KB
GPIO3 Support Registers
0x481B_0000
0x481B_FFFF
0x081B_0000
0x081B_FFFF
64KB
Reserved
0x481C_0000
0x481C_0FFF
0x081C_0000
0x081C_0FFF
4KB
Reserved
0x481C_1000
0x481C_1FFF
0x081C_1000
0x081C_1FFF
4KB
TIMER8 Peripheral Registers
0x481C_2000
0x481C_2FFF
0x081C_2000
0x081C_2FFF
4KB
TIMER8 Support Registers
0x481C_3000
0x481C_3FFF
4KB
SYNCTIMER32K Peripheral Registers
0x481C_4000
0x481C_4FFF
4KB
SYNCTIMER32K Support Registers
0x481C_5000
0x481C_5FFF
4KB
PLLSS Peripheral Registers
0x481C_6000
0x481C_6FFF
4KB
PLLSS
0x481C_7000
0x481C_7FFF
4KB
WDT0 Peripheral Registers
0x481C_8000
0x481C_8FFF
4KB
WDT0 Support Registers
0x481C_9000
0x481C_9FFF
0x081C_9000
0x081C_9FFF
8KB
Reserved
0x481C_A000
0x481C_BFFF
0x081C_A000
0x081C_BFFF
8KB
Reserved
0x481C_C000
0x481C_DFFF
8KB
DCAN0 Peripheral Registers
Device Overview
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 2-7. L4 Slow Peripheral Memory Map (continued)
Cortex-A8 and L3 Masters
(1)
C674x DSP
START
ADDRESS
(HEX)
END ADDRESS
(HEX)
0x481C_E000
0x481C_FFFF
8KB
DCAN0 Support Registers
0x481D_0000
0x481D_1FFF
8KB
DCAN1 Peripheral Registers
0x481D_2000
0x481D_3FFF
8KB
DCAN1 Support Registers
0x481D_4000
0x481D_5FFF
0x081D_4000
0x081D_5FFF
8KB
Reserved
0x481D_6000
0x481D_6FFF
0x081D_6000
0x081D_6FFF
4KB
Reserved
0x481D_7000
0x481D_7FFF
0x081D_7000
0x081D_7FFF
4KB
Reserved
0x481D_8000
0x481E_7FFF
64KB
MMC/SD/SDIO1 Peripheral Registers
0x481E_8000
0x481E_8FFF
4KB
MMC/SD/SDIO1 Support Registers
0x481E_9000
0x481F_FFFF
52KB
Reserved
0x4820_0000
0x4820_0FFF
4KB
Interrupt controller (1)
0x4820_1000
0x4823_FFFF
0x4824_0000
0x4824_0FFF
0x4824_1000
0x4827_FFFF
0x4828_0000
0x4828_0FFF
0x4828_1000
0x482F_FFFF
0x0828_1000
0x4830_0000
0x48FF_FFFF
0x0830_0000
START
ADDRESS (HEX)
0x081E_9000
0x0820_1000
END ADDRESS
(HEX)
0x081F_FFFF
0x0823_FFFF
SIZE
DEVICE NAME
Reserved (1)
252KB
MPUSS config register (1)
4KB
0x0824_1000
252KB
Reserved (1)
4KB
Reserved (1)
0x082F_FFFF
508KB
Reserved (1)
0x08FF_FFFF
13MB
Reserved
0x0827_FFFF
These regions decoded internally by the Cortex™-A8 Subsystem and are not physically part of the L4 Slow. They are included here only
for reference when considering the Cortex™-A8 Memory Map. For Masters other than the Cortex-A8 these regions are reserved.
2.12.5 DDR DMM TILER Extended Addressing Map
The TILER includes an additional 4-GBytes of addressing range, enabled by a 33rd address bit, to access
the frame buffer in rotated and mirrored views. shows the details of the TILER Extended Address
Mapping. This entirety of this additional range is only accessible to the HDVPSS and ISS subsystems.
However, other masters can access any one single view through the 512-MB TILER region in the base
4GByte address memory map.
Table 2-8. DDR DMM TILER Extended Address Mapping
BLOCK NAME
START ADDRESS
(HEX)
END ADDRESS
(HEX)
SIZE
DESCRIPTION
TILER View 0
0x1 0000_0000
0x1 1FFF_FFFF
512MB
Natural 0° View
TILER View 1
0x1 2000_0000
0x1 3FFF_FFFF
512MB
0° with Vertical Mirror
View
TILER View 2
0x1 4000_0000
0x1 5FFF_FFFF
512MB
0° with Horizontal Mirror
View
TILER View 3
0x1 6000_0000
0x1 7FFF_FFFF
512MB
180° View
TILER View 4
0x1 8000_0000
0x1 9FFF_FFFF
512MB
90° with Vertical Mirror
View
270° View
TILER View 5
0x1 A000_0000
0x1 BFFF_FFFF
512MB
TILER View 6
0x1 C000_0000
0x1 DFFF_FFFF
512MB
90° View
TILER View 7
0x1 E000_0000
0x1 FFFF_FFFF
512MB
90° with Horizontal Mirror
View
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Overview
33
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3 Device Pins
3.1
Pin Maps
Figure 3-1 through Figure 3-8 show the bottom view of the package pin assignments in eight pin maps (A,
B, C, D, E, F, G, and H).
34
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
E F G H
A B C D
P
SD1_DAT[0]
SD1_CMD/
GP0[0]
N
SD0_CMD/
SD1_CMD/
GP0[2]
MCA[2]_AXR[0]/
SD0_DAT[6]/
UART5_RXD
GP0[12]
M
MCA[1]_ACLKR/
MCA[1]_AXR[4]
MCA[1]_AFSR/
MCA[1]_AXR[5]
MCA[0]_AXR[5]/
MCA[1]_AXR[9]
MCA[0]_AXR[6]/
MCB_DR
L
MCA[0]_AXR[8]/
MCB_FSX/
MCB_FSR
MCA[0]_AXR[7]/
MCB_DX
MCA[0]_AFSX
MCA[0]_AXR[2]/
I2C[3]_SDA
K
MCA[0]_AFSR/
MCA[5]_AXR[3]
MCA[0]_ACLKR/
MCA[5]_AXR[2]
J
MCA[0]_AXR[1]/
I2C[3]_SCL
MCA[0]_AXR[0]
H
AUD_CLKIN2/
MCA[0]_AXR[9]/
MCA[2]_AHCLKX/
MCA[5]_AHCLKX/
EDMA_EVT2/
TIM3_IO/
GP0[9]
MCA[2]_AXR[3]/
MCA[1]_AXR[7]/
TIM3_IO/
GP0[15]
G
MCA[3]_AXR[0]/
TIM4_IO/
GP0[18]
MCA[3]_AXR[1]/
TIM5_IO/
GP0[19]
F
POR
MCA[3]_AXR[2]/
MCA[1]_AXR[8]/
GP0[20]
DDR[1]_D[1]
DDR[1]_DQM[0]
E
DDR[1]_D[3]
DDR[1]_D[2]
DDR[1]_D[0]
DDR[1]_D[5]
D
DDR[1]_DQS[0]
DDR[1]_DQS[0]
DDR[1]_D[6]
C
DDR[1]_D[7]
DDR[1]_D[8]
DDR[1]_D[10]
B
DDR[1]_VTP
DDR[1]_DQM[1]
A
VSS
1
SD1_CLK
SD1_DAT[2]_SDRW
SD1_DAT[1]_SDIRQ
SD1_DAT[3]
DVDD_SD
MCA[1]_AXR[3]/
MCB_CLKR
DVDD
MCA[0]_AXR[3]
MCA[0]_AXR[9]/
MCB_CLKX/
MCB_CLKR
VDDA_1P8
AUD_CLKIN0/
MCA[0]_AXR[7]/
MCA[0]_AHCLKX/
MCA[3]_AHCLKX]/
USB1_DRVVBUS
MCA[5]_AXR[1]/
MCA[4]_AXR[3]/
TIM7_IO/
GP0[28]
MCA[5]_AXR[0]/
MCA[4]_AXR[2]/
GP0[27]
RSTOUT_WD_OUT
MCA[4]_ACLKX/
GP0[21]
MCA[5]_ACLKX/
GP0[25]
MCA[4]_AXR[1]/
TIM6_IO/
GP0[24]
RESET
MCA[3]_AXR[3]/
MCA[1]_AXR[9]
CLKIN32/
CLKOUT0/
TIM3_IO/
GP3[31]
MCA[4]_AFSX/
GP0[22]
MCA[3]_AFSX/
GP0[17]
MCA[5]_AFSX/
GP0[26]
MCA[4]_AXR[0]/
GP0[23]
NMI
MCA[3]_ACLKX/
GP0[16]
DDR[1]_D[17]
DDR[1]_D[4]
DDR[1]_D[21]
DDR[1]_D[9]
DDR[1]_D[22]
DDR[1]_D[13]
DDR[1]_D[18]
DDR[1]_D[20]
DDR[1]_DQS[1]
DDR[1]_D[12]
DDR[1]_D[19]
DDR[1]_DQS[2]
DDR[1]_D[23]
DDR[1]_D[11]
DDR[1]_DQS[1]
DDR[1]_D[14]
DDR[1]_D[15]
DDR[1]_DQS[2]
DDR[1]_D[27]
2
3
4
5
6
7
Figure 3-1. Pin Map A
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
35
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
E F G H
A B C D
P
DVDD
DVDD_SD
LDOCAP_DSP
VDDA_DSPPLL_1P8
CVDD
VSS
CVDD
N
VSS
CVDD_DSP
LDOCAP_HDVICP
LDOCAP_HDVICPRAM
VSS
CVDD_HDVICP
CVDD_HDVICP
M
DVDD
VSS
CVDD_DSP
LDOCAP_DSPRAM
CVDD_DSP
CVDD_HDVICP
CVDD_HDVICP
L
VSS
CVDD_DSP
CVDD_DSP
CVDD_DSP
CVDD_DSP
VSS
CVDD_HDVICP
CVDD
CVDD_DSP
VSS
CVDD
VSS
VSS
DVDD_DDR[1]
DVDD_DDR[1]
VSS
DVDD_DDR[1]
VSS
K
J
H
DDR[1]_D[16]
DDR[1]_D[25]
DDR[1]_ODT[0]
DDR[1]_CKE
DVDD_DDR[1]
DVDD_DDR[1]
DVDD_DDR[1]
G
DDR[1]_DQM[2]
DDR[1]_DQM[3]
DDR[1]_RST
DDR[1]_CS[1]
DDR[1]_CS[0]
DVDD_DDR[1]
VREFSSTL_DDR[1]
F
DDR[1]_D[26]
DDR[1]_D[24]
DDR[1]_A[1]
DDR[1]_ODT[1]
DDR[1]_A[10]
DDR[1]_CAS
DDR[1]_BA[0]
E
DVDD_DDR[1]
DVDD_DDR[1]
DDR[1]_A[13]
DDR[1]_WE
DDR[1]_A[8]
D
DDR[1]_D[29]
VSS
DDR[1]_A[14]
DDR[1]_BA[2]
DDR[1]_A[6]
C
DDR[1]_D[30]
DDR[1]_D[28]
DDR[1]_A[2]
DDR[1]_RAS
DDR[1]_A[9]
B
DDR[1]_DQS[3]
DDR[1]_D[31]
DDR[1]_A[12]
DDR[1]_A[0]
DDR[1]_A[5]
DDR[1]_CLK
DDR[1]_A[4]
A
DDR[1]_DQS[3]
DDR[1]_A[7]
DDR[1]_BA[1]
DDR[1]_A[11]
VSS
DDR[1]_CLK
DDR[1]_A[3]
8
9
10
11
12
13
14
Figure 3-2. Pin Map B
36
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
E F G H
A B C D
VSS
CVDD
VSS
LDOCAP_RAM0
VSS
DVDD_GPMCB
VSS
P
VSS
VSS
CVDD
VDDA_L3PLL_1P8
CVDD
VSS
VSS
N
VSS
CVDD
VSS
CVDD
VSS
DVDD_GPMC
VSS
M
CVDD
VSS
CVDD
LDOCAP_RAM2
CVDD
VDDA_1P8
DVDD_GPMC
L
VSS
VSS
VSS
CVDD
VSS
DVDD_GPMC
DVDD_DDR[0]
DVDD_DDR[0]
DVDD_DDR[0]
DVDD_DDR[0]
VSS
VDDA_DDRPLL_1P8
DVDD_DDR[0]
DVDD_DDR[0]
DDR[0]_CKE
DDR[0]_ODT[1]
DDR[0]_D[24]
DDR[0]_D[18]
H
VREFSSTL_DDR[0]
DVDD_DDR[0]
DDR[0]_CS[1]
DDR[0]_ODT[0]
DDR[0]_RST
DDR[0]_D[26]
DDR[0]_D[19]
G
DDR[0]_BA[0]
DDR[0]_A[14]
DDR[0]_A[13]
DDR[0]_CS[0]
DDR[0]_A[1]
DDR[0]_DQM[3]
DDR[0]_D[25]
F
DDR[0]_A[3]
DDR[0]_A[12]
DDR[0]_A[7]
DVDD_DDR[0]
DVDD_DDR[0]
E
DDR[0]_A[4]
DDR[0]_A[11]
DDR[0]_A[2]
VSS
DDR[0]_D[30]
D
DDR[0]_A[9]
DDR[0]_WE
DDR[0]_CAS
DDR[0]_D[28]
DDR[0]_D[29]
C
K
J
DDR[0]_A[8]
DDR[0]_CLK
DDR[0]_A[5]
DDR[0]_RAS
DDR[0]_A[0]
DDR[0]_D[31]
DDR[0]_DQS[3]
B
DDR[0]_A[6]
DDR[0]_CLK
VSS
DDR[0]_BA[2]
DDR[0]_A[10]
DDR[0]_BA[1]
DDR[0]_DQS[3]
A
15
16
17
18
19
20
21
Figure 3-3. Pin Map C
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
37
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
E F G H
A B C D
SD2_DAT[5]/
GPMC_A[26]/
GPMC_A[22]/
TIM6_IO/
GP1[21]
EMAC[0]_MRXD[1]/
EMAC[0]_RGRXD[0]/
VIN[1]B_D[6]/
EMAC[0]_RMTXD[1]/
GP3[29]
VSS
SD2_DAT[6]/
GPMC_A[25]/
GPMC_A[21]/
UART2_TXD/
GP1[20]
VDDA_1P8
SD2_CLK/
GP1[15]
SD2_DAT[1]_SDIRQ/
GPMC_A[3]/
GP1[13]
GPMC_CS[2]/
GPMC_A[24]/
GP1[25]
VSS
EMAC[0]_MCOL/
EMAC[0]_RGRXCTL/
VIN[1]B_D[1]/
EMAC[0]_RMRXD[0]/
GP3[24]
EMAC[0]_MTCLK/
EMAC[0]_RGRXC/
VIN[1]B_D[0]/
SPI[3]_SCS[3]/
I2C[2]_SDA/
GP3[23]
SD2_DAT[7]/
GPMC_A[24]/
GPMC_A[20]/
UART2_RXD/
GP1[19]
EMAC[0]_MRXDV/
EMAC[1]_RGRXD[1]/
GPMC_A[5]/
SPI[2]_SCLK
EMAC[0]_GMTCLK/
EMAC[1]_RGRXC/
GPMC_A[6]/
SPI[2]_D[1]
EMAC[0]_MTXD[6]/
EMAC[1]_RGRXD[0]/
EMAC[1]_RMTXD[0]/
GPMC_A[13]/
UART1_TXD
EMAC[0]_MTXEN/
EMAC[1]_RGRXD[2]/
EMAC[1]_RMTXEN/
GPMC_A[15]/
UART1_RTS
EMAC[0]_MTXD[0]/
EMAC[1]_RGRXD[3]/
GPMC_A[7]/
SPI[2]_D[0]
EMAC[0]_MRXD[3]/
EMAC[1]_RGRXCTL/
GPMC_A[27]/
GPMC_A[26]/
GPMC_A[0]/
UART5_RXD
EMAC[0]_MTXD[2]/
EMAC[1]_RGTXCTL/
EMAC[1]_RMRXD[0]/
GPMC_A[9]/
UART4_TXD
EMAC[0]_MTXD[3]/
EMAC[1]_RGTXD[0]/
EMAC[1]_RMRXD[1]/
GPMC_A[10]/
UART4_CTS
EMAC[0]_MTXD[7]/
EMAC[1]_RGTXD[3]/
EMAC[1]_RMTXD[1]/
GPMC_A[14]/
UART1_CTS
EMAC[0]_MTXD[1]/
EMAC[1]_RGTXD[1]/
GPMC_A[8]/
UART4_RXD
MDIO/
GP1[12]
GPMC_CS[4]/
SD2_CMD/
GP1[8]
GPMC_CS[3]/
VIN[1]B_CLK/
SPI[2]_SCS[0]/
GP1[26]
RSV13
RSV12
P
RSV11
RSV10
N
GPMC_ADV_ALE/
GPMC_CS[6]/
TIM5_IO/
GP1[28]
RSV8
RSV9
M
SD2_DAT[0]/
GPMC_A[4]/
GP1[14]
RSV6
RSV7
L
SD2_DAT[2]_SDRW/
GPMC_A[2]/
GP2[6]
GPMC_CS[1]/
GPMC_A[25]/
GP1[24]
K
EMAC[0]_MRXER/
EMAC[0]_RGTXCTL/
VIN[1]B_D[3]/
EMAC[0]_RMRXER/
GP3[26]
EMAC_RMREFCLK/
TIM2_IO/
GP1[10]
SD2_DAT[3]/
GPMC_A[1]/
GP2[5]
J
EMAC[0]_MRXD[5]/
EMAC[0]_RGTXD[3]/
GPMC_A[2]/
UART5_CTS
EMAC[0]_MRCLK/
EMAC[0]_RGTXC/
VIN[1]B_D[4]/
EMAC[0]_RMCRSDV/
SPI[3]_SCS[2]/
GP3[27]
MDCLK/
GP1[11]
H
EMAC[0]_MRXD[7]/
EMAC[0]_RGTXD[1]/
GPMC_A[4]/
SPI[2]_SCS[3]
EMAC[0]_MRXD[0]/
EMAC[0]_RGTXD[0]/
VIN[1]B_D[5]/
EMAC[0]_RMTXD[0]/
GP3[28]
G
EMAC[0]_MTXD[4]/
EMAC[1]_RGTXD[2]/
EMAC[1]_RMRXER/
GPMC_A[11]/
UART4_RTS
DDR[0]_D[17]
DDR[0]_D[4]
DDR[0]_D[21]
DDR[0]_D[3]
DDR[0]_D[1]
EMAC[0]_MTXD[5]/
EMAC[1]_RGTXC/
EMAC[1]_RMCRSDV/
GPMC_A[12]/
UART1_RXD
EMAC[0]_MRXD[6]/
EMAC[0]_RGTXD[2]/
GPMC_A[3]/
UART5_RTS
F
DDR[0]_D[5]
DDR[0]_D[2]
DDR[0]_D[0]
DDR[0]_DQM[0]
E
DDR[0]_D[6]
DDR[0]_DQS[0]
DDR[0]_DQS[0]
D
DDR[0]_D[20]
DDR[0]_D[13]
DDR[0]_D[22]
DDR[0]_DQM[2]
DDR[0]_D[9]
DDR[0]_D[10]
DDR[0]_D[8]
DDR[0]_D[7]
C
DDR[0]_D[23]
DDR[0]_DQS[2]
DDR[0]_D[16]
DDR[0]_D[12]
DDR[0]_DQS[1]
DDR[0]_VTP
DDR[0]_DQM[1]
B
DDR[0]_D[27]
DDR[0]_DQS[2]
DDR[0]_D[15]
DDR[0]_D[14]
DDR[0]_DQS[1]
DDR[0]_D[11]
VSS
A
22
23
24
25
26
27
28
Figure 3-4. Pin Map D
38
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
AH
VSS
DEVOSC_MXI/
DEV_CLKIN
DEVOSC_MXO
UART0_DCD/
UART3_RXD/
SPI[0]_SCS[3]/
I2C[2]_SCL/
SD1_POW/
GP1[2]
UART0_RXD
DCAN0_TX/
UART2_TXD/
I2C[3]_SDA/
GP1[0]
VOUT[0]_G_Y_YC[2]/
EMU3/
GP2[24]
AG
VSS
UART0_DTR/
UART3_CTS/
UART1_TXD/
GP1[4]
VSSA_DEVOSC
UART0_DSR/
UART3_TXD/
SPI[0]_SCS[2]/
I2C[2]_SDA/
SD1_SDWP/
GP1[3]
UART0_TXD
DCAN0_RX/
UART2_RXD/
I2C[3]_SCL/
GP1[1]
VOUT[0]_B_CB_C[2]
EMU2/
GP2[22]
AF
SERDES_CLKP
SERDES_CLKN
SPI[0]_D[1]
UART0_RIN/
UART3_RTS/
UART1_RXD/
GP1[5]
UART0_RTS/
UART4_TXD/
DCAN1_RX/
SPI[1]_SCS[2]/
SD2_SDCD
VOUT[0]_R_CR[6]/
SPI[0]_SCS[1]/
SD1_SDCD/
SATA_ACT0_LED/
EDMA_EVT1/
TIM4_IO/
GP1[6]
UART0_CTS/
UART4_RXD/
DCAN1_TX/
SPI[1]_SCS[3]/
SD0_SDCD
AE
VSS
VSS
SPI[0]_D[0]
AD
PCIE_TXN0
PCIE_TXP0
SPI[1]_SCS[0]/
GP1[16]
RTCK
AC
PCIE_RXN0
PCIE_RXP0
SPI[1]_SCLK/
GP1[17]
I2C[0]_SCL
AB
SATA_TXN0
SATA_TXP0
AA
SATA_RXP0
SATA_RXN0
SPI[1]_D[1]/
GP1[18]
TRST
MCA[2]_AFSX/
GP0[11]
SPI[1]_D[0]/
GP1[26]
TMS
Y
VSS
VSS
SD0_DAT[2]_SDRW/
SD1_DAT[6]/
GP0[5]
SD0_DAT[3]/
SD1_DAT[7]/
GP0[6]
SD0_DAT[1]_SDIRQ/
SD1_DAT[5]/
GP0[4]
SD0_CLK/
GP0[1]
TDI
W
GP1[7]
GP1[8]
DEVOSC_WAKE/
SPI[1]_SCS[1]/
TIM5_IO/
GP1[7]
TCLK
V
GP1[9]
GP1[10]
MCA[1]_AFSX
MCA[1]_AXR[0]/
SD0_DAT[4]
MCA[2]_AXR[2]/
MCA[1]_AXR[6]/
TIM2_IO/
GP0[14]
MCA[2]_AXR[1]/
SD0_DAT[7]/
UART5_TXD/
GP0[13]
VSS
U
RSV16
RSV17
UART2_TXD/
GP0[31]
UART2_RXD/
GP0[29]
MCA[1]_ACLKX
MCA[2]_ACLKX//
GP0[10]
VDDA_1P8
T
AUXOSC_MXO
TCLKIN/
GP0[30]
MCA[1]_AXR[1]/
SD0_DAT[5]
DVDD
MCA[0]_AXR[4]/
MCA[1]_AXR[8]
SD0_DAT[0]/
SD1_DAT[4]/
GP0[3]
6
7
R
SPI[0]_SCS[0]
SPI[0]_SCLK
TDO
I2C[0]_SDA
AUXOSC_MXI/
AUX_CLKIN
VSSA_AUXOSC
MCA[1]_AXR[2]/
MCB_FSR
MCA[0]_ACLKX
AUD_CLKIN1/
MCA[0]_AXR[8]/
MCA[1]_AHCLKX/
MCA[4]_AHCLKX/
EDMA_EVT3/
TIM2_IO/
GP0[8]
1
2
3
4
5
E F G H
A B C D
Figure 3-5. Pin Map E
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
39
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
AH
VIN[0]A_D[4]/
GP2[9]
VIN[0]A_D[10]_BD[2]/
GP2[15]
USB0_CE
USB0_DM
USB1_ID
USB1_DM
USB1_CE
AG
EMU0
VIN[0]A_D[9]_BD[1]/
GP2[14]
USB0_ID
USB0_DP
USB0_VBUSIN
USB1_DP
USB1_VBUSIN
AF
VOUT[0]_R_CR[5]
VIN[0]A_D[0]/
GP1[11]
USB0_DRVVBUS/
GP0[7]
VOUT[0]_R_CR[7]
VOUT[0]_G_Y_YC[9]
AE
VOUT[0]_R_CR[8]
VSS
EMU1
VIN[0]A_D[3]/
GP2[8]
VOUT[0]_G_Y_YC[8]
AD
RSV1
VOUT[0]_R_CR[2]/
EMU4/
GP2[26]
VOUT[0]_B_CB_C[4]
VOUT[0]_CLK
VOUT[0]_G_Y_YC[7]
AC
RSV5
VIN[0]A_D[2]/
GP2[7]
VOUT[0]_B_CB_C[6]
VOUT[0]_HSYNC
VIN[0]A_D[14]_BD[6]/
CAM_STROBE/
GP2[19]
VOUT[0]_R_CR[9]
VIN[0]A_D[15]_BD[7]/
CAM_SHUTTER/
GP2[20]
AB
VOUT[0]_G_Y_YC[4]
VOUT[0]_R_CR[3]/
GP2[27]
VOUT[0]_B_CB_C[7]
VIN[0]A_D[1]/
GP1[12]
VOUT[0]_G_Y_YC[5]
VOUT[0]_VSYNC
DVDD
AA
VOUT[0]_G_Y_YC[6]
VOUT[0]_R_CR[4]
VOUT[0]_AVID/
VOUT[0]_FLD/
SPI[3]_SCLK/
TIM7_IO/
GP2[21]
VIN[0]A_D[7]/
GP2[12]
VDDA_USB0_1P8
VDDA_USB_3P3
VSS
VSS
DVDD
VSS
VDDA_1P8
RSV4
VDDA_PCIE_1P8
VDDA_PCIE_1P8
CVDD
VSS
VDDA_USB1_1P8
LDOCAP_ARM
Y
W
V
RSV3
VSS
VDDA_1P8
VSS
VSSA_USB
VSSA_USB
LDOCAP_ARMRAM
U
RSV2
VDDA_SATA_1P8
VDDA_SATA_1P8
CVDD
VSS
CVDD
VSS
T
VSS
VSS
LDOCAP_SGX
LDOCAP_SERDESCLK
CVDD
VSS
CVDD_ARM
R
VSS
VSS
DVDD_M
LDOCAP_RAM1
VSS
VDDA_ARMPLL_1P8
VSS
8
9
10
11
12
13
14
E F G H
A B C D
Figure 3-6. Pin Map F
40
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
VOUT[0]_G_Y_YC[3]/
GP2[25]
VIN[0]A_D[6]/
GP2[11]
VIN[0]A_D[11]_BD[3]/
CAM_WE/
GP2[16]
HDMI_CLKN
HDMI_DN0
HDMI_DN1
HDMI_DN2
AH
VOUT[0]_B_CB_C[9]
VIN[0]A_D[5]/
GP2[10]
VIN[0]A_D[12]_BD[4]/
CLKOUT1/
GP2[17]
HDMI_CLKP
HDMI_DP0
HDMI_DP1
HDMI_DP2
AG
VOUT[0]_B_CB_C[8]
VIN[0]A_D[13]_BD[5]/
CAM_RESET/
GP2[18]
VOUT[0]_FLD/
CAM_PCLK/
GPMC_A[12]/
UART2_RTS/
GP2[2]
VIN[0]A_D[18]/
CAM_D[10]/
EMAC[1]_RMRXD[1]/
I2C[3]_SCL/
GP0[12]
VIN[0]A_D[19]/
CAM_D[11]/
EMAC[1]_RMRXD[0]/
I2C[3]_SDA/
GP0[13]
AF
VOUT[0]_B_CB_C[3]/
GP2[23]
VIN[0]B_CLK/
CLKOUT0/
GP1[9]
VIN[0]A_D[21]/
CAM_D[13]/
EMAC[1]_RMTXD[0]/
SPI[3]_SCLK/
GP0[15]
VSS
VIN[0]A_DE/
VIN[0]B_HSYNC/
UART5_TXD/
I2C[2]_SDA/
GP2[0]
AE
VOUT[0]_B_CB_C[5]
VIN[0]B_FLD/
CAM_D[4]/
GP0[21]
VOUT[1]_G_Y_YC[1]/
CAM_D[3]/
GPMC_A[5]/
UART4_RXD/
GP0[22]
VIN[0]A_VSYNC/
UART5_CTS/
GP2[4]
VSS
AD
VIN[0]B_DE/
CAM_D[6]/
GP0[19]
VIN[0]A_D[23]/
CAM_D[15]/
EMAC[1]_RMTXEN/
SPI[3]_D[0]/
GP0[17]
VIN[0]A_D[20]/
CAM_D[12]/
EMAC[1]_RMCRSDV/
SPI[3]_SCS[0]/
GP0[14]
VOUT[1]_G_Y_YC[0]/
CAM_D[2]/
GPMC_A[6]/
UART4_TXD/
GP0[23]
VOUT[1]_R_CR[1]/
CAM_D[1]/
GPMC_A[7]/
UART4_CTS/
GP0[24]
VIN[0]A_HSYNC/
UART5_RTS/
GP2[3]
VIN[0]A_D[22]/
CAM_D[14]/
EMAC[1]_RMTXD[1]/
SPI[3]_D[1]/
GP0[16]
AC
VIN[0]A_D[8]_BD[0]/
GP2[13]
DVDD
VIN[0]A_DE/
CAM_D[7]/
GP0[18]
VDDA_VID0PLL_1P8
VDDA_VDAC_1P8
VIN[0]A_CLK/
GP2[2]
VIN[0]A_D[17]/
CAM_D[9]/
EMAC[1]_RMRXER/
GP0[11]
AB
DVDD
VSS
DVDD
VDDA_VID1PLL_1P8
VSSA_VDAC
VIN[0]A_FLD/
VIN[0]B_VSYNC/
UART5_RXD/
I2C[2]_SCL/
GP2[1]
VIN[0]A_D[16]/
CAM_D[8]/
I2C[2]_SCL/
GP0[10]
AA
VSS
DVDD
VSS
VSS
VSS
VDDA_1P8
VSS
VSS
VDDA_HDMI_1P8
DVDD_C
DVDD_C
CVDD_ARM
CVDD_ARM
VSS
VSSA_HDMI
VSS
DVDD
VSS
V
CVDD_ARM
CVDD_ARM
CVDD
VSS
CVDD
VSS
DVDD
U
CVDD_ARM
CVDD_ARM
VSS
VSS
VSS
DVDD_GPMCB
VSS
T
CVDD
VSS
CVDD
VDDA_AUDIOPLL_1P8
CVDD
VDDA_1P8
VSS
R
15
16
17
18
19
20
21
Y
W
E F G H
A B C D
Figure 3-7. Pin Map G
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
41
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
TV_OUT1
TV_VFB1
www.ti.com
TV_RSET
TV_OUT0
VOUT[1]_B_CB_C[3]/
EMAC[1]_MRCLK/
VIN[1]A_D[0]/
UART4_CTS/
GP3[0]
VOUT[1]_B_CB_C[8]/
EMAC[1]_MRXD[4]/
VIN[1]A_D[5]/
I2C[3]_SCL/
GP3[5]
VOUT[1]_G_Y_YC[6]/
EMAC[1]_GMTCLK/
VIN[1]A_D[11]/
GP3[10]
VSS
AH
TV_VFB0
I2C[1]_SDA/
HDMI_SDA
VOUT[1]_B_CB_C[4]/
EMAC[1]_MRXD[0]/
VIN[1]A_D[1]/
UART4_RXD/
GP3[1]
VOUT[1]_G_Y_YC[5]/
EMAC[1]_MRXDV/
VIN[1]A_D[10]/
GP3[9]
VOUT[1]_R_CR[4]/
EMAC[1]_MTXD[3]/
VIN[1]A_D[15]/
SPI[3]_SCS[1]/
GP3[14]
VOUT[1]_R_CR[3]/
GPMC_A[14]/
VIN[1]A_D[22]/
HDMI_SDA/
SPI[2]_SCLK/
I2C[2]_SDA
GP3[21]
AG
VSS
I2C[1]_SCL/
HDMI_SCL
VOUT[1]_B_CB_C[5]/
EMAC[1]_MRXD[1]/
VIN[1]A_D[2]/
UART4_TXD/
GP3[2]
VOUT[1]_G_Y_YC[7]/
EMAC[1]_MTXD[0]/
VIN[1]A_D[12]/
GP3[11]
VOUT[1]_G_Y_YC[2]/
GPMC_A[13]/
VIN[1]A_D[21]/
HDMI_SCL/
SPI[2]_SCS[2]/
I2C[2]_SCL/
GP3[20]
VOUT[1]_B_CB_C[2]/
GPMC_A[0]/
VIN[1]A_D[7]/
HDMI_CEC/
SPI[2]_D[0]/
GP3[30]
AF
VOUT[1]_B_CB_C[1]/
CAM_HS/
GPMC_A[9]/
UART2_RXD/
GP0[26]
VOUT[1]_CLK/
EMAC[1]_MTCLK/
VIN[1]A_HSYNC/
GP2[28]
VOUT[1]_G_Y_YC[8]/
EMAC[1]_MTXD[1]/
VIN[1]A_D[13]/
GP3[12]
VOUT[1]_R_CR[2]/
GPMC_A[15]/
VIN[1]A_D[23]/
HDMI_HPDET/
SPI[2]_D[1]/
GP3[22]
GPMC_A[18]/
TIM2_IO/
GP1[13]
AE
VOUT[1]_B_CB_C[6 ]/
EMAC[1]_MRXD[2]/
VIN[1]A_D[3]/
UART3_RXD/
GP3[3]
VOUT[1]_G_Y_YC[9]/
EMAC[1]_MTXD[2]/
VIN[1]A_D[14]/
GP3[13]
GPMC_A[16]/
GP2[5]
GPMC_A[20]/
SPI[2]_SCS[1]/
GP1[15]
AD
VOUT[1]_B_CB_C[7]/
EMAC[1]_MRXD[3]/
VIN[1]A_D[4]/
UART3_TXD/
GP3[4]
VOUT[1]_R_CR[5]/
EMAC[1]_MTXD[4]/
VIN[1]A_D[16]/
SPI[3]_SCLK/
GP3[15]
GPMC_A[19]/
TIM3_IO/
GP1[14]
GPMC_A[21]/
SPI[2]_D[0]/
GP1[16]
AC
GPMC_A[22]/
SPI[2]_D[1]/
HDMI_CEC/
TIM4_IO/
GP1[17]
GPMC_D[9]/
BTMODE[9]
AB
VOUT[1]_B_CB_C[0]/
CAM_VS/
GPMC_A[10]/
UART2_TXD/
GP0[27]
VOUT[1]_HSYNC/
EMAC[1]_MCOL/
VIN[1]A_VSYNC/
SPI[3]_D[1]/
UART3_RTS/
GP2[29]
VIN[0]A_FLD/
CAM_D[5]/
GP0[20]
VOUT[1]_FLD/
CAM_FLD/
CAM_WE/
GPMC_A[11]/
UART2_CTS/
GP0[28]
VOUT[1]_R_CR[0]/
CAM_D[0]/
GPMC_A[8]/
UART4_RTS/
GP0[25]
VOUT[1]_VSYNC/
EMAC[1]_MCRS/
VIN[1]A_FLD/
VIN[1]A_DE/
SPI[3]_D[0]/
UART3_CTS/
GP2[30]
VOUT[1]_B_CB_C[9]/
EMAC[1]_MRXD[5]/
VIN[1]A_D[6]/
I2C[3]_SDA/
GP3[6]
VOUT[1]_R_CR[6]/
EMAC[1]_MTXD[5]/
VIN[1]A_D[17]/
SPI[3]_D[1]/
GP3[16]
GPMC_A[23]/
SPI[2]_SCLK/
HDMI_HPDET/
TIM5_IO/
GP1[18]
GPMC_D[11]/
BTMODE[11]
GPMC_D[5]/
BTMODE[5]
AA
VOUT[1]_AVID/
EMAC[1]_MRXER/
VIN[1]A_CLK/
UART4_RTS/
TIM6_IO/
GP2[31]
VOUT[1]_G_Y_YC[3]/
EMAC[1]_MRXD[6]/
VIN[1]A_D[8]/
GP3[7]
VOUT[1]_R_CR[9]/
EMAC[1]_MTXEN/
VIN[1]A_D[20]/
UART5_TXD/
GP3[19]
GPMC_D[15]/
BTMODE[15]
GPMC_D[10]/
BTMODE[10]
GPMC_D[8]/
BTMODE[8]
GPMC_D[1]/
BTMODE[1]
Y
VOUT[1]_G_Y_YC[4]/
EMAC[1]_MRXD[7]/
VIN[1]A_D[9]/
GP3[8]
VOUT[1]_R_CR[8]/
EMAC[1]_MTXD[7]/
VIN[1]A_D[19]/
UART5_RXD/
GP3[18]
GPMC_D[3]/
BTMODE[3]
GPMC_WAIT[0]/
GPMC_A[26]/
EDMA_EVT0/
GP1[31]
W
VOUT[1]_R_CR[7]/
EMAC[1]_MTXD[6]/
VIN[1]A_D[18]/
SPI[3]_D[0]/
GP3[17]
GPMC_A[17]/
GP2[6]
GPMC_D[14]/
BTMODE[14]
GPMC_D[7]/
BTMODE[7]
GPMC_D[4]/
BTMODE[4]
GPMC_D[2]/
BTMODE[2]
GPMC_BE[1]/
GPMC_A[24]/
EDMA_EVT1/
TIM7_IO/
GP1[30]
V
DVDD
GPMC_D[13]/
BTMODE[13]
GPMC_D[12]/
BTMODE[12]
GPMC_D[6]/
BTMODE[6]
GPMC_D[0]/
BTMODE[0]
GPMC_BE[0]_CLE/
GPMC_A[25]/
EDMA_EVT2/
TIM6_IO/
GP1[29]
GPMC_WE
U
VSS
EMAC[0]_MRXD[4]/
EMAC[0]_RGRXD[3]/
GPMC_A[1]/
UART5_TXD
GPMC_OE_RE
GPMC_CS[0]/
GP1[23]
T
VSS
EMAC[0]_MRXD[2]/
EMAC[0]_RGRXD[1]/
VIN[1]B_D[7]/
EMAC[0]_RMTXEN/
GP3[30]
SD2_DAT[4]/
GPMC_A[27]/
GPMC_A[23]/
GPMC_CS[7]/
EDMA_EVT0/
TIM7_IO/
GP1[22]
EMAC[0]_MCRS/
EMAC[0]_RGRXD[2]/
VIN[1]B_D[2]/
EMAC[0]_RMRXD[1]/
GP3[25]
GPMC_CLK/
GPMC_CS[5]/
GPMC_WAIT[1]/
CLKOUT1/
EDMA_EVT3/
TIM4_IO/
GP1[27]
RSV14
RSV15
R
22
23
24
25
26
27
28
E F G H
A B C D
Figure 3-8. Pin Map H
42
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
3.2
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Terminal Functions
The terminal functions tables identify the external signal names and their pin multiplexing, the associated
pin (ball) numbers along with the mechanical package designator, the pin type (for example, I, O, Z, S, A,
or GND), whether the pin has any internal pullup or pulldown resistors (for example, IPU, IPD, or DIS), the
supply voltage source, and describe the function or functions on the pin. The MUXED column in the tables
also identifies all peripheral pin functions multiplexed on a pin, the pin control register (PINCNTLx) that
controls which peripheral pin function is selected for that particular pin, and indicates the state driven on
the peripheral input (logic 0, logic 1, or PIN level) when the peripheral pin function is not selected (that is,
the de-selected input state [DSIS]), and the Multi-Muxed [MM] option for that peripheral pin function). For
more detailed information on device configuration, boot mode order, peripheral selection, and
multiplexed/shared pin control, and so on, see Section 4, Device Configurations of this data manual.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
43
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.1
www.ti.com
Boot Configuration
Table 3-1. Boot Configuration Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
BOOT
GPMC_D[15]/
BTMODE[15]
Y25
I
DIS
DVDD_GPMC
GPMC
PINCNTL104
DSIS: PIN
GPMC CS0 default GPMC_Wait enable input. This pin is
multiplexed between ARM Cortex-A8 boot mode and
General-Purpose Memory Controller (GPMC) peripheral
functions. At reset, BTMODE[15] is sampled to determine
the GPMC CS0 Wait enable:
•
•
0 = Wait disabled
1 = Wait enabled
After reset, this pin functions as GPMC multiplexed
data/address pin 15 (GPMC_D[15]).
GPMC_D[14]/
BTMODE[14]
GPMC_D[13]/
BTMODE[13]
V24
U23
I
DIS
DVDD_GPMC
GPMC
PINCNTL103
DSIS: PIN
I
DIS
DVDD_GPMC
GPMC
PINCNTL102
DSIS: PIN
GPMC CS0 default Address/Data multiplexing mode
input. These pins are multiplexed between ARM CortexA8 boot mode and General-Purpose Memory Controller
(GPMC) peripheral functions. At reset, BTMODE[14:13]
are sampled to determine the GPMC CS0 Address/Data
multiplexing:
•
•
•
•
00
01
10
11
= Not muxed
= A/A/D muxed
= A/D muxed
= Reserved
After reset, this pin functions as GPMC multiplexed
data/address pins 14 through 13 (GPMC_D[14:13]).
GPMC_D[12]/
BTMODE[12]
U24
I
DIS
DVDD_GPMC
GPMC
PINCNTL101
DSIS: PIN
GPMC CS0 default Data Bus Width input. This pin is
multiplexed between ARM Cortex-A8 boot mode and
General-Purpose Memory Controller (GPMC) peripheral
functions. At reset, BTMODE[12] is sampled to determine
the GPMC CS0 bus width:
•
•
0 = 8-bit data bus
1 = 16-bit data bus
After reset, this pin functions as GPMC multiplexed
data/address pin 12 (GPMC_D[12]).
RSTOUT_WD_OUT Configuration. This pin is
multiplexed between ARM Cortex-A8 boot mode and
General-Purpose Memory Controller (GPMC) peripheral
functions. At reset, BTMODE[11] is sampled to determine
the function of the RSTOUT_WD_OUT pin:
GPMC_D[11]/
BTMODE[11]
AA27
I
DIS
DVDD_GPMC
GPMC
PINCNTL100
DSIS: PIN
•
•
0 = RSTOUT is asserted when a Watchdog Timer
reset, POR, RESET, or Emulation/Software-Global
Cold/Warm reset occurs
1 = RSTOUT_WD_OUT is asserted only when a
Watchdog Timer reset occurs
After reset, this pin functions as GPMC multiplexed
data/address pin 11 (GPMC_D[11]).
(1)
(2)
(3)
44
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-1. Boot Configuration Terminal Functions (continued)
SIGNAL
NAME
GPMC_D[10]/
BTMODE[10]
NO.
Y26
TYPE (1)
I
OTHER (2)
(3)
DIS
DVDD_GPMC
MUXED
GPMC
PINCNTL99
DSIS: PIN
DESCRIPTION
XIP (NOR) on GPMC Configuration. This pin is
multiplexed between ARM Cortex-A8 boot mode and
General-Purpose Memory Controller (GPMC) peripheral
functions. At reset, when the XIP (MUX0), XIP (MUX1),
XIP w/ WAiT (MUX0) or XIP w/ WAiT (MUX1) bootmode
is selected (see Table 4-1), BTMODE[10] is sampled to
select between GPMC pin muxing options A or B shown
in Table 4-2, XIP (on GPMC) Boot Options [Muxed or
Non-Muxed].
•
•
0 = GPMC Option A
1 = GPMC Option B
After reset, this pin functions as GPMC multiplexed
data/address pin 10 (GPMC_D[10]).
GPMC_D[9]/
BTMODE[9]
GPMC_D[8]/
BTMODE[8]
AB28
Y27
I
I
DIS
DVDD_GPMC
DIS
DVDD_GPMC
GPMC
PINCNTL98
DSIS: PIN
GPMC
PINCNTL97
DSIS: PIN
Ethernet PHY Configuration. These pins are multiplexed
between ARM Cortex-A8 boot mode and GeneralPurpose Memory Controller (GPMC) peripheral functions.
At reset, when EMAC bootmode is selected (see Table 41), BTMODE[9:8] pins are sampled to determine the
function of the Ethernet PHY Mode selection.
•
•
•
•
00
01
10
11
= MII (GMII)
= RMII
= RGMII
= Reserved
For more detailed information on the EMAC PHY boot
modes and the EMAC pin functions selected, see
Section 4.2.6, Ethernet PHY Mode Selection.
After reset, these pins function as GPMC multiplexed
data/address pins 9 and 8 (GPMC_D[9] and
GPMC_D[8]).
GPMC_D[7]/
BTMODE[7]
V25
I
DIS
DVDD_GPMC
GPMC
PINCNTL96
DSIS: PIN
GPMC_D[6]/
BTMODE[6]
U25
I
DIS
DVDD_GPMC
GPMC
PINCNTL95
DSIS: PIN
GPMC_D[5]/
BTMODE[5]
AA28
I
DIS
DVDD_GPMC
GPMC
PINCNTL94
DSIS: PIN
GPMC_D[4]/
BTMODE[4]
V26
I
DIS
DVDD_GPMC
GPMC
PINCNTL93
DSIS: PIN
GPMC_D[3]/
BTMODE[3]
W27
I
DIS
DVDD_GPMC
GPMC
PINCNTL92
DSIS: PIN
GPMC_D[2]/
BTMODE[2]
V27
I
DIS
DVDD_GPMC
GPMC
PINCNTL91
DSIS: PIN
GPMC_D[1]/
BTMODE[1]
Y28
I
DIS
DVDD_GPMC
GPMC
PINCNTL90
DSIS: PIN
GPMC_D[0]/
BTMODE[0]
U26
I
DIS
DVDD_GPMC
GPMC
PINCNTL89
DSIS: PIN
Reserved Boot Pins. These pins are multiplexed between
ARM Cortex-A8 boot mode and General-Purpose
Memory Controller (GPMC) peripheral functions.
For proper device operation at reset, these pins should
be externally pulled low.
After reset, these pins function as GPMC multiplexed
data/address pins 10 through 5 (GPMC_D[7:5]).
ARM Cortex-A8 Boot Mode Configuration Bits. These
pins are multiplexed between ARM Cortex-A8 boot mode
and the General-Purpose Memory Controller (GPMC)
peripheral functions.
At reset, the boot mode inputs BTMODE[4:0] are
sampled to determine the ARM boot configuration. For
more details on the types of boot modes supported, see
Section 4.2, Boot Modes, of this document, along with
the TMS320DM814x ROM Code Memory and Peripheral
Booting chapter of the TMS320DM814x DaVinci™ Digital
Media Processors Technical Reference Manual
(Literature Number: SPRUGZ8).
After reset, these pins function as GPMC multiplexed
data/address pins 4 through 0 (GPMC_D[4:0]).
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
45
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.2
www.ti.com
Camera Interface (I/F)
Table 3-2. Camera I/F Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
CAMERA I/F
VOUT[0]_FLD/
CAM_PCLK/
GPMC_A[12]/
UART2_RTS/
GP2[2]
AF18
VIN[0]A_D[23]/
CAM_D[15]/
EMAC[1]_RMTXEN/
SPI[3]_D[0]/
GP0[17]
VIN[0]A_D[22]/
CAM_D[14]/
EMAC[1]_RMTXD[1]/
SPI[3]_D[1]/
GP0[16]
VIN[0]A_D[21]/
CAM_D[13]/
EMAC[1]_RMTXD[0]/
SPI[3]_SCLK/
GP0[15]
I
IPD
DVDD_C
VOUT[0], GPMC, UART2,
GP2
Camera Pixel Clock.
PINCNTL175
DSIS: 0
AC16
I
IPD
DVDD_C
VIN[0]A, EMAC[1], SPI[3],
GP0
PINCNTL163
DSIS: PIN
AC21
I
IPD
DVDD_C
VIN[0]A, EMAC[1]_RM,
SPI[3], GP0
PINCNTL162
DSIS: PIN
I
IPD
DVDD_C
VIN[0]A, EMAC[1]_RM,
SPI[3], GP0
PINCNTL161
DSIS: PIN
I
IPD
DVDD_C
VIN[0]A, EMAC[1]_RM,
SPI[3], GP0
PINCNTL160
DSIS: PIN
AE18
VIN[0]A_D[20]/
CAM_D[12]/
EMAC[1]_RMCRSDV/
SPI[3]_SCS[0]/
GP0[14]
AC17
VIN[0]A_D[19]/
CAM_D[11]/
EMAC[1]_RMRXD[0]/
I2C[3]_SDA/
GP0[13]
AF21
I
IPU
DVDD_C
VIN[0]A, EMAC[1]_RM,
I2C[3], GP0
PINCNTL159
DSIS: PIN
VIN[0]A_D[18]/
CAM_D[10]/
EMAC[1]_RMRXD[1]/
I2C[3]_SCL/
GP0[12]
AF20
I
IPU
DVDD_C
VIN[0]A, EMAC[1]_RM,
I2C[3], GP0
PINCNTL158
DSIS: PIN
VIN[0]A, EMAC[1]_RM,
GP0
PINCNTL157
DSIS: PIN
VIN[0]A, I2C[2], GP0
PINCNTL156
DSIS: PIN
VIN[0]A_D[17]/
CAM_D[9]/
EMAC[1]_RMRXER/
GP0[11]
AB21
I
IPD
DVDD_C
VIN[0]A_D[16]/
CAM_D[8]/
I2C[2]_SCL/
GP0[10]
AA21
I
IPU
DVDD_C
(1)
(2)
(3)
46
Camera data inputs
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-2. Camera I/F Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
VIN[0]A_DE/
CAM_D[7]/
GP0[18]
AB17
I
IPU
DVDD_C
VIN[0]A, GP0
PINCNTL164
DSIS: PIN
VIN[0]B_DE/
CAM_D[6]/
GP0[19]
AC15
I
IPU
DVDD_C
VIN[0]A, GP0
PINCNTL165
DSIS: PIN
VIN[0]A_FLD/
CAM_D[5]/
GP0[20]
AC22
I
IPU
DVDD_C
VIN[0]A, GP0
PINCNTL166
DSIS: PIN
VIN[0]B_FLD/
CAM_D[4]/
GP0[21]
AD17
I
IPU
DVDD_C
VIN[0]B, GP0
PINCNTL167
DSIS: PIN
VOUT[1]_G_Y_YC[1]/
CAM_D[3]/
GPMC_A[5]/
UART4_RXD/
GP0[22]
AD18
I
IPU
DVDD_C
VOUT[1], GPMC, UART4,
GP0
PINCNTL168
Camera data inputs
DSIS: PIN
VOUT[1], GPMC, UART4,
GP0
PINCNTL169
DSIS: PIN
VOUT[1]_G_Y_YC[0]/
CAM_D[2]/
GPMC_A[6]/
UART4_TXD/
GP0[23]
AC18
I
IPD
DVDD_C
VOUT[1]_R_CR[1]/
CAM_D[1]/
GPMC_A[7]/
UART4_CTS/
GP0[24]
AC19
I
IPD
DVDD_C
VOUT[1], GPMC, UART4,
GP0
PINCNTL170
DSIS: PIN
VOUT[1]_R_CR[0]/
CAM_D[0]/
GPMC_A[8]/
UART4_RTS/
GP0[25]
AA22
I
IPD
DVDD_C
VOUT[1], GPMC, UART4,
GP0
PINCNTL171
DSIS: PIN
VOUT[1], GPMC, UART2,
GP0
Camera Horizontal Synchronization
PINCNTL172
DSIS: 0
VOUT[1], GPMC, UART2,
GP0
Camera Vertical Synchronization
PINCNTL173
DSIS: 0
VOUT[1]_B_CB_C[1]/
CAM_HS/
GPMC_A[9]/
UART2_RXD/
GP0[26]
AE23
I/O
IPD
DVDD_C
VOUT[1]_B_CB_C[0]/
CAM_VS/
GPMC_A[10]/
UART2_TXD/
GP0[27]
AD23
I/O
IPU
DVDD_C
VIN[0]A_D[13]_BD[5]/
CAM_RESET/
GP2[18]
AF17
I/O
IPD
DVDD
VIN[0]AB, GP2
PINCNTL153
DSIS: 0
VIN[0]A_D[11]_BD[3]/
CAM_WE/
GP2[16]
AH17
I
IPD
DVDD
VIN[0]AB. GP2
PINCNTL151
DSIS: 0
MM: MUX1
I
IPD
DVDD_C
VOUT[1], CAMERA_I/F,
GPMC, UART2, GP0
PINCNTL174
DSIS: 0
MM: MUX0
I/O
IPD
DVDD_C
VOUT[1], CAMERA_I/F,
GPMC, UART2, GP0
PINCNTL174
DSIS: 0
VOUT[1]_FLD/
CAM_FLD/
CAM_WE/
GPMC_A[11]/
UART2_CTS/
GP0[28]
VOUT[1]_FLD/
CAM_FLD/
CAM_WE/
GPMC_A[11]/
UART2_CTS/
GP0[28]
AB23
AB23
Camera Reset. Used for Strobe Synchronization
Camera Write Enable
Camera Field Identification input
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
47
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-2. Camera I/F Terminal Functions (continued)
SIGNAL
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
NAME
NO.
VIN[0]A_D[14]_BD[6]/
CAM_STROBE/
GP2[19]
AC12
O
IPD
DVDD
VIN[0]AB, GP2
PINCNTL154
DSIS: N/A
Camera Flash Strobe Control Signal
VIN[0]A_D[15]_BD[7]/
CAM_SHUTTER/
GP2[20]
AC14
O
IPD
DVDD
VIN[0]AB, GP2
PINCNTL155
DSIS: N/A
Camera Mechanical Shutter Control Signal
48
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
3.2.3
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Controller Area Network (DCAN) Modules (DCAN0, DCAN1)
Table 3-3. DCAN Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
DCAN0
DCAN0_RX/
UART2_RXD/
I2C[3]_SCL/
GP1[1]
AG6
I/O
IPU
DVDD
UART2, I2C[3], GP1
PINCNTL69
DSIS: 1
DCAN0 receive data pin.
DCAN0_TX/
UART2_TXD/
I2C[3]_SDA/
GP1[0]
AH6
I/O
IPU
DVDD
UART2, I2C[3], GP1
PINCNTL68
DSIS: 1
DCAN0 transmit data pin.
DCAN1
UART0_RTS/
UART4_TXD/
DCAN1_RX/
SPI[1]_SCS[2]/
SD2_SDCD
AF5
I/O
IPU
DVDD
UART0, UART4, SPI[1],
SD2
PINCNTL73
DSIS: 1
DCAN1 receive data pin.
UART0_CTS/
UART4_RXD/
DCAN1_TX/
SPI[1]_SCS[3]/
SD0_SDCD
AE6
I/O
IPU
DVDD
UART0, UART4, SPI[1],
SD0
PINCNTL72
DSIS: 1
DCAN1 transmit data pin.
(1)
(2)
(3)
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
49
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.4
www.ti.com
DDR2/DDR3 Memory Controller
Table 3-4. DDR2/DDR3 Memory Controller 0 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
DDR2/DDR3 Memory Controller 0 (DDR[0])
DDR[0]_CLK
B16
O
IPD/DIS
DVDD_DDR[0]
DDR[0] Clock
The internal pulldown (IPD) is enabled for this pin when the device is
in reset and the IPD is disabled (DIS) when reset is released.
DDR[0]_CLK
A16
O
IPU/DIS
DVDD_DDR[0]
DDR[0] Negative Clock
The internal pullup (IPU) is enabled for this pin when the device is in
reset and the IPU is disabled (DIS) when reset is released.
DDR[0]_CKE
H18
O
IPD
DVDD_DDR[0]
DDR[0] Clock Enable
DDR[0]_WE
C17
O
IPU/DIS
DVDD_DDR[0]
DDR[0] Write Enable
The internal pullup (IPU) is enabled for this pin when the device is in
reset and the IPU is disabled (DIS) when reset is released.
DDR[0]_CS[0]
F18
O
IPU/DIS
DVDD_DDR[0]
DDR[0] Chip Select 0
The internal pullup (IPU) is enabled for this pin when the device is in
reset and the IPU is disabled (DIS) when reset is released.
DDR[0]_CS[1]
G17
O
IPU/DIS
DVDD_DDR[0]
DDR[0] Chip Select 1
The internal pullup (IPU) is enabled for this pin when the device is in
reset and the IPU is disabled (DIS) when reset is released.
DDR[0]_RAS
B18
O
IPU/DIS
DVDD_DDR[0]
DDR[0] Row Address Strobe output
The internal pullup (IPU) is enabled for this pin when the device is in
reset and the IPU is disabled (DIS) when reset is released.
DDR[0]_CAS
C18
O
IPU/DIS
DVDD_DDR[0]
DDR[0] Column Address Strobe output
The internal pullup (IPU) is enabled for this pin when the device is in
reset and the IPU is disabled (DIS) when reset is released.
DDR[0]_DQM[3]
F20
O
IPU/IPD
DVDD_DDR[0]
DDR[0]_DQM[2]
C24
O
IPU/IPD
DVDD_DDR[0]
DDR[0]_DQM[1]
B28
O
IPU/IPD
DVDD_DDR[0]
DDR[0]_DQM[0]
E28
O
IPU/IPD
DVDD_DDR[0]
DDR[0]_DQS[3]
B21
I/O
IPD
DVDD_DDR[0]
DDR[0]_DQS[2]
B23
I/O
IPD
DVDD_DDR[0]
DDR[0]_DQS[1]
B26
I/O
IPD
DVDD_DDR[0]
DDR[0]_DQS[0]
D28
I/O
IPD
DVDD_DDR[0]
DDR[0]_DQS[3]
A21
I/O
IPU
DVDD_DDR[0]
DDR[0]_DQS[2]
A23
I/O
IPU
DVDD_DDR[0]
DDR[0]_DQS[1]
A26
I/O
IPU
DVDD_DDR[0]
DDR[0]_DQS[0]
D27
I/O
IPU
DVDD_DDR[0]
(1)
(2)
(3)
50
DDR[0] Data Mask outputs
DDR[0]_DQM[3]: For upper byte data bus DDR[0]_D[31:24]
DDR[0]_DQM[2]: For DDR[0]_D[23:16]
DDR[0]_DQM[1]: For DDR[0]_D[15:8]
DDR[0]_DQM[0]: For lower byte data bus DDR[0]_D[7:0]
The internal pullup (IPU) is enabled for these pins when the device is
in reset and switches to an IPD enabled when reset is released.
Data strobe input/outputs for each byte of the 32-bit data bus. They
are outputs to the DDR[0] memory when writing and inputs when
reading. They are used to synchronize the data transfers.
DDR[0]_DQS[3]: For upper byte data bus DDR[0]_D[31:24]
DDR[0]_DQS[2]: For DDR[0]_D[23:16]
DDR[0]_DQS[1]: For DDR[0]_D[15:8]
DDR[0]_DQS[0]: For lower byte data bus DDR[0]_D[7:0]
Complementary data strobe input/outputs for each byte of the 32-bit
data bus. They are outputs to the DDR[0] memory when writing and
inputs when reading. They are used to synchronize the data
transfers.
DDR[0]_DQS[3]: For upper byte data bus DDR[0]_D[31:24]
DDR[0]_DQS[2]: For DDR[0]_D[23:16]
DDR[0]_DQS[1]: For DDR[0]_D[15:8]
DDR[0]_DQS[0]: For lower byte data bus DDR[0]_D[7:0]
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-4. DDR2/DDR3 Memory Controller 0 Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
DDR[0]_ODT[0]
G18
O
IPD/DIS
DVDD_DDR[0]
DDR[0] On-Die Termination for Chip Select 0.
The internal pulldown (IPD) is enabled for this pin when the device is
in reset and the IPD is disabled (DIS) when reset is released.
DDR[0]_ODT[1]
H19
O
IPD/DIS
DVDD_DDR[0]
DDR[0] On-Die Termination for Chip Select 1.
The internal pulldown (IPD) is enabled for this pin when the device is
in reset and the IPD is disabled (DIS) when reset is released.
DDR[0]_RST
G19
O
IPD/DIS
DVDD_DDR[0]
DDR[0]_BA[2]
A18
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_BA[1]
A20
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_BA[0]
F15
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[14]
F16
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[13]
F17
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[12]
E17
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[11]
D17
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[10]
A19
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[9]
C15
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[8]
B15
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[7]
E18
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[6]
A15
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[5]
B17
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[4]
D15
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[3]
E15
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[2]
D18
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[1]
F19
O
IPU/DIS
DVDD_DDR[0]
DDR[0]_A[0]
B19
O
IPU/DIS
DVDD_DDR[0]
DDR[0] Reset output
The internal pulldown (IPD) is enabled for this pin when the device is
in reset and the IPD is disabled (DIS) when reset is released.
DDR[0] Bank Address outputs
The internal pullup (IPU) is enabled for these pins when the device is
in reset and the IPU is disabled (DIS) when reset is released.
DDR[0] Address Bus
The internal pullup (IPU) is enabled for these pins when the device is
in reset and the IPU is disabled (DIS) when reset is released.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
51
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-4. DDR2/DDR3 Memory Controller 0 Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DDR[0]_D[31]
B20
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[30]
D21
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[29]
C21
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[28]
C20
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[27]
A22
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[26]
G20
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[25]
F21
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[24]
H20
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[23]
B22
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[22]
C23
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[21]
E23
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[20]
D23
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[19]
G21
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[18]
H21
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[17]
F22
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[16]
B24
I/O
IPD
DVDD_DDR[0]
52
Device Pins
DESCRIPTION
DDR[0] Data Bus
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-4. DDR2/DDR3 Memory Controller 0 Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DDR[0]_D[15]
A24
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[14]
A25
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[13]
D24
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[12]
B25
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[11]
A27
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[10]
C26
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[9]
C25
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[8]
C27
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[7]
C28
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[6]
D26
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[5]
E25
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[4]
F24
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[3]
F25
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[2]
E26
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[1]
F26
I/O
IPD
DVDD_DDR[0]
DDR[0]_D[0]
E27
I/O
IPD
DVDD_DDR[0]
DDR[0]_VTP
B27
I
–
DVDD_DDR[0]
DESCRIPTION
DDR[0] Data Bus
DDR VTP Compensation Resistor Connection
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
53
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-5. DDR2/DDR3 Memory Controller 1 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
DDR2/DDR3 Memory Controller 1 (DDR[1])
DDR[1]_CLK
B13
O
DDR[1] Clock
IPD/DIS
The internal pulldown (IPD) is enabled for this pin when the device is
DVDD_DDR[1]
in reset and the IPD is disabled (DIS) when reset is released.
DDR[1]_CLK
A13
O
DDR[1] Negative Clock
IPU/DIS
The internal pullup (IPU) is enabled for this pin when the device is in
DVDD_DDR[1]
reset and the IPU is disabled (DIS) when reset is released.
DDR[1]_CKE
H11
O
IPD
DDR[1] Clock Enable
DVDD_DDR[1]
DDR[1]_WE
E12
O
DDR[1] Write Enable
IPU/DIS
The internal pullup (IPU) is enabled for this pin when the device is in
DVDD_DDR[1]
reset and the IPU is disabled (DIS) when reset is released.
DDR[1]_CS[0]
G12
O
DDR[1] Chip Select 0
IPU/DIS
The internal pullup (IPU) is enabled for this pin when the device is in
DVDD_DDR[1]
reset and the IPU is disabled (DIS) when reset is released.
DDR[1]_CS[1]
G11
O
DDR[1] Chip Select 1
IPU/DIS
The internal pullup (IPU) is enabled for this pin when the device is in
DVDD_DDR[1]
reset and the IPU is disabled (DIS) when reset is released.
DDR[1]_RAS
C12
O
DDR[1] Row Address Strobe output
IPU/DIS
The internal pullup (IPU) is enabled for this pin when the device is in
DVDD_DDR[1]
reset and the IPU is disabled (DIS) when reset is released.
DDR[1]_CAS
F13
O
DDR[1] Column Address Strobe output
IPU/DIS
The internal pullup (IPU) is enabled for this pin when the device is in
DVDD_DDR[1]
reset and the IPU is disabled (DIS) when reset is released.
DDR[1]_DQM[3]
G9
O
DDR[1]_DQM[2]
G8
O
DDR[1]_DQM[1]
B2
O
DDR[1]_DQM[0]
F4
O
DDR[1]_DQS[3]
B8
I/O
DDR[1]_DQS[2]
A6
I/O
DDR[1]_DQS[1]
B3
I/O
DDR[1]_DQS[0]
D1
I/O
DDR[1]_DQS[3]
A8
I/O
DDR[1]_DQS[2]
B6
I/O
DDR[1]_DQS[1]
A3
I/O
DDR[1]_DQS[0]
D2
I/O
DDR[1]_ODT[0]
H10
O
(1)
(2)
(3)
54
IPU/IPD
DVDD_DDR[1] DDR[1] Data Mask outputs
DDR[1]_DQM[3]: For upper byte data bus DDR[1]_D[31:24]
IPU/IPD
DDR[1]_DQM[2]: For DDR[1]_D[23:16]
DVDD_DDR[1] DDR[1]_DQM[1]: For DDR[1]_D[15:8]
DDR[1]_DQM[0]: For lower byte data bus DDR[1]_D[7:0]
IPU/IPD
DVDD_DDR[1]
The internal pullup (IPU) is enabled for these pins when the device is
IPU/IPD
in reset and switches to an IPD enabled when reset is released.
DVDD_DDR[1]
IPD
DVDD_DDR[1] Data strobe input/outputs for each byte of the 32-bit data bus. They are
outputs to the DDR[1] memory when writing and inputs when reading.
IPD
DVDD_DDR[1] They are used to synchronize the data transfers.
DDR[1]_DQS[3]: For upper byte data bus DDR[1]_D[31:24]
IPD
DDR[1]_DQS[2]: For DDR[1]_D[23:16]
DVDD_DDR[1] DDR[1]_DQS[1]: For DDR[1]_D[15:8]
DDR[1]_DQS[0]: For lower byte data bus DDR[1]_D[7:0]
IPD
DVDD_DDR[1]
IPU
DVDD_DDR[1] Complementary data strobe input/outputs for each byte of the 32-bit
data bus. They are outputs to the DDR[1] memory when writing and
IPU
DVDD_DDR[1] inputs when reading. They are used to synchronize the data transfers.
DDR[1]_DQS[3]: For upper byte data bus DDR[1]_D[31:24]
IPU
DDR[1]_DQS[2]: For DDR[1]_D[23:16]
DVDD_DDR[1] DDR[1]_DQS[1]: For DDR[1]_D[15:8]
DDR[1]_DQS[0]: For lower byte data bus DDR[1]_D[7:0]
IPU
DVDD_DDR[1]
DDR[1] On-Die Termination for Chip Select 0.
IPD/DIS
The internal pulldown (IPD) is enabled for this pin when the device is
DVDD_DDR[1]
in reset and the IPD is disabled (DIS) when reset is released.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-5. DDR2/DDR3 Memory Controller 1 Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
DDR[1]_ODT[1]
F11
O
DDR[1] On-Die Termination for Chip Select 1.
IPD/DIS
The internal pulldown (IPD) is enabled for this pin when the device is
DVDD_DDR[1]
in reset and the IPD is disabled (DIS) when reset is released.
DDR[1]_RST
G10
O
DDR[1] Reset output.
IPD/DIS
The internal pulldown (IPD) is enabled for this pin when the device is
DVDD_DDR[1]
in reset and the IPD is disabled (DIS) when reset is released.
DDR[1]_BA[2]
D12
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_BA[1]
A10
O
DDR[1]_BA[0]
F14
O
DDR[1]_A[14]
D11
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[13]
E11
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[12]
B10
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[11]
A11
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[10]
F12
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[9]
C14
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[8]
E14
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[7]
A9
O
DDR[1]_A[6]
D14
O
DDR[1]_A[5]
B12
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[4]
B14
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[3]
A14
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[2]
C11
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[1]
F10
O
IPU/DIS
DVDD_DDR[1]
DDR[1]_A[0]
B11
O
IPU/DIS
DVDD_DDR[1]
DDR[1] Bank Address outputs
IPU/DIS
DVDD_DDR[1] The internal pullup (IPU) is enabled for these pins when the device is
in reset and the IPU is disabled (DIS) when reset is released.
IPU/DIS
DVDD_DDR[1]
DDR[1] Address Bus
IPU/DIS
DVDD_DDR[1] The internal pullup (IPU) is enabled for these pins when the device is
in reset and the IPU is disabled (DIS) when reset is released.
IPU/DIS
DVDD_DDR[1]
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
55
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-5. DDR2/DDR3 Memory Controller 1 Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DDR[1]_D[31]
B9
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[30]
C8
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[29]
D8
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[28]
C9
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[27]
A7
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[26]
F8
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[25]
H9
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[24]
F9
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[23]
B7
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[22]
D6
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[21]
E6
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[20]
C6
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[19]
B5
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[18]
C5
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[17]
F7
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[16]
H8
I/O
IPD
DVDD_DDR[1]
56
Device Pins
DESCRIPTION
DDR[1] Data Bus
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-5. DDR2/DDR3 Memory Controller 1 Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DDR[1]_D[15]
A5
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[14]
A4
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[13]
C4
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[12]
B4
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[11]
A2
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[10]
C3
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[9]
D5
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[8]
C2
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[7]
C1
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[6]
D3
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[5]
E4
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[4]
F5
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[3]
E1
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[2]
E2
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[1]
F3
I/O
IPD
DVDD_DDR[1]
DDR[1]_D[0]
E3
I/O
IPD
DVDD_DDR[1]
DDR[1]_VTP
B1
I
DESCRIPTION
DDR[1] Data Bus
–
DDR[1] VTP Compensation Resistor Connection
DVDD_DDR[1]
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
57
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.5
www.ti.com
EDMA
Table 3-6. EDMA Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
EDMA
AUD_CLKIN1/
MCA[0]_AXR[8]/
MCA[1]_AHCLKX/
MCA[4]_AHCLKX/
EDMA_EVT3/
TIM2_IO/
GP0[8]
GPMC_CLK/
GPMC_CS[5]/
GPMC_WAIT[1]/
CLKOUT1/
EDMA_EVT3/
TIM4_IO/
GP1[27]
AUD_CLKIN2/
MCA[0]_AXR[9]/
MCA[2]_AHCLKX/
MCA[5]_AHCLKX/
EDMA_EVT2/
TIM3_IO/
GP0[9]
GPMC_BE[0]_CLE/
GPMC_A[25]/
EDMA_EVT2/
TIM6_IO/
GP1[29]
SPI[0]_SCS[1]/
SD1_SDCD/
SATA_ACT0_LED/
EDMA_EVT1/
TIM4_IO/
GP1[6]
GPMC_BE[1]/
GPMC_A[24]/
EDMA_EVT1/
TIM7_IO/
GP1[30]
R5
R26
H1
U27
AE5
V28
SD2_DAT[4]/
GPMC_A[27]/
GPMC_A[23]/
GPMC_CS[7]/
EDMA_EVT0/
TIM7_IO/
GP1[22]
R24
GPMC_WAIT[0]/
GPMC_A[26]/
EDMA_EVT0/
GP1[31]
W28
(1)
(2)
(3)
58
I
I
I
IPD
DVDD
AUD_CLKIN1,
MCA[0], MCA[1],
MCA[4], TIMER2,
GP0
PINCNTL15
DSIS: PIN
MM: MUX1
IPU
DVDD_GPMC
GPMC, CLKOUT1,
TIMER4, GP1
PINCNTL127
DSIS: PIN
MM: MUX0
IPD
DVDD
AUD_CLKIN2,
MCA[0], MCA[2].
MCA[5], TIMER3,
GP0
PINCNTL16
DSIS: PIN
MM: MUX1
IPD
DVDD_GPMC
GPMC, TIMER6,
GP1
PINCNTL131
DSIS: PIN
MM: MUX0
IPU
DVDD
SPI[0], SD1,
SATA, TIMER4,
GP1
PINCNTL80
DSIS: PIN
MM: MUX1
I
IPD
DVDD_GPMC
GPMC, TIMER7,
GP1
PINCNTL132
DSIS: PIN
MM: MUX0
I
IPU
DVDD_GPMC
SD2, GPMC,
TIMER7, GP1
PINCNTL116
DSIS: PIN
MM: MUX1
I
I
I
IPU
DVDD_GPMC
External EDMA Event 3
External EDMA Event 2
External EDMA Event 1
External EDMA Event 0
GPMC, GP1
PINCNTL133
DSIS: PIN
MM: MUX0
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and the Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
3.2.6
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
EMAC [(R)(G)MII Modes] and MDIO
Table 3-7. EMAC[0] Terminal Functions [(R)(G)MII]
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
EMAC[0] (G)MII Mode
An EMAC bootmode must be selected via the BTMODE[4:0] pins. Once the EMAC bootmode is selected, the BTMODE[9:8] pins determine
the Ethernet PHY Mode Selection (for example, 00b is MII mode). For more detailed information on EMAC bootmodes and Ethernet PHY
Mode selection, see Section 4.2.6, Ethernet PHY Mode Selection.
These pin functions are available only when GMII or MII modes are selected.
EMAC[0]_MCOL/
EMAC[0]_RGRXCTL/
VIN[1]B_D[1]/
EMAC[0]_RMRXD[0]/
GP3[24]
L23
EMAC[0]_MCRS/
EMAC[0]_RGRXD[2]/
VIN[1]B_D[2]/
EMAC[0]_RMRXD[1]/
GP3[25]
EMAC[0]_GMTCLK/
EMAC[1]_RGRXC/
GPMC_A[6]/
SPI[2]_D[1]
EMAC[0]_MRCLK/
EMAC[0]_RGTXC/
VIN[1]B_D[4]/
EMAC[0]_RMCRSDV/
SPI[3]_SCS[2]/
GP3[27]
(1)
(2)
(3)
I
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, GP3
PINCNTL236
DSIS: 0
[G]MII Collision Detect (Sense) input
R25
I
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, GP3
PINCNTL237
DSIS: 0
[G]MII Carrier Sense input
K23
O
IPD
DVDD_GPMC
EMAC[1],
GPMC, SPI[2]
PINCNTL249
DSIS: N/A
GMII Source Synchronous Transmit Clock
I
IPD
DVDD_GPMC
H27
EMAC[0],
VIN[1]B, SPI[3],
GP3
[G]MII Receive Clock
PINCNTL239
DSIS: 0
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
59
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-7. EMAC[0] Terminal Functions [(R)(G)MII] (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
EMAC[0]_MRXD[7]/
EMAC[0]_RGTXD[1]/
GPMC_A[4]/
SPI[2]_SCS[3]
G27
EMAC[0],
GPMC, SPI[2]
PINCNTL247
DSIS: PIN
EMAC[0]_MRXD[6]/
EMAC[0]_RGTXD[2]/
GPMC_A[3]/
UART5_RTS
F28
EMAC[0],
GPMC, UART5
PINCNTL246
DSIS: PIN
EMAC[0]_MRXD[5]/
EMAC[0]_RGTXD[3]/
GPMC_A[2]/
UART5_CTS
H26
EMAC[0],
GPMC, UART5
PINCNTL245
DSIS: PIN
EMAC[0]_MRXD[4]/
EMAC[0]_RGRXD[3]/
GPMC_A[1]/
UART5_TXD
T23
EMAC[0],
GPMC, UART5
PINCNTL244
DSIS: PIN
EMAC[0]_MRXD[3]/
EMAC[1]_RGRXCTL/
GPMC_A[27]/
GPMC_A[26]/
GPMC_A[0]/
UART5_RXD
J25
EMAC[0]_MRXD[2]/
EMAC[0]_RGRXD[1]/
VIN[1]B_D[7]/
EMAC[0]_RMTXEN/
GP3[30]
R23
EMAC[0],
VIN[1]B, GP3
PINCNTL242
DSIS: PIN
EMAC[0]_MRXD[1]/
EMAC[0]_RGRXD[0]/
VIN[1]B_D[6]/
EMAC[0]_RMTXD[1]/
GP3[29]
P23
EMAC[0],
VIN[1]B, GP3
PINCNTL241
DSIS: PIN
G28
EMAC[0],
VIN[1]B, GP3
PINCNTL240
DSIS: PIN
EMAC[0]_MRXD[0]/
EMAC[0]_RGTXD[0]/
VIN[1]B_D[5]/
EMAC[0]_RMTXD[0]/
GP3[28]
EMAC[0]_MRXDV/
EMAC[1]_RGRXD[1]/
GPMC_A[5]/
SPI[2]_SCLK
K22
EMAC[0]_MRXER/
EMAC[0]_RGTXCTL/
VIN[1]B_D[3]/
EMAC[0]_RMRXER/
GP3[26]
J26
EMAC[0]_MTCLK/
EMAC[0]_RGRXC/
VIN[1]B_D[0]/
SPI[3]_SCS[3]/
I2C[2]_SDA/
GP3[23]
60
Device Pins
L24
I
IPD
DVDD_GPMC
EMAC[1],
GPMC, UART5
PINCNTL243
DSIS: PIN
DESCRIPTION
[G]MII Receive Data [7:0]. For 1000 EMAC GMII
operation, EMAC[0]_RXD[7:0] are used. For 10/100
EMAC MII operation, only EMAC[0]_RXD[3:0] are
used.
I
IPD
DVDD_GPMC
EMAC[1],
GPMC, SPI[2]
PINCNTL248
DSIS: 0
[G]MII Receive Data Valid input
I
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, GP3
PINCNTL238
DSIS: 0
[G]MII Receive Data Error input
I
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, SPI[3],
I2C[2], GP3
[G]MII Transmit Clock input
PINCNTL235
DSIS: 0
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-7. EMAC[0] Terminal Functions [(R)(G)MII] (continued)
SIGNAL
NAME
EMAC[0]_MTXD[7]/
EMAC[1]_RGTXD[3]/
EMAC[1]_RMTXD[1]/
GPMC_A[14]/
UART1_CTS
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
H24
EMAC[1],
GPMC, UART1
PINCNTL257
DSIS: N/A
J22
EMAC[1],
GPMC, UART1
PINCNTL256
DSIS: N/A
EMAC[0]_MTXD[5]/
EMAC[1]_RGTXC/
EMAC[1]_RMCRSDV/
GPMC_A[12]/
UART1_RXD
F27
EMAC[1],
GPMC, UART1
PINCNTL255
DSIS: N/A
EMAC[0]_MTXD[4]/
EMAC[1]_RGTXD[2]/
EMAC[1]_RMRXER/
GPMC_A[11]/
UART4_RTS
G23
EMAC[1],
GPMC, UART4
PINCNTL254
DSIS: N/A
EMAC[0]_MTXD[3]/
EMAC[1]_RGTXD[0]/
EMAC[1]_RMRXD[1]/
GPMC_A[10]/
UART4_CTS
H23
EMAC[1],
GPMC, UART4
PINCNTL253
DSIS: N/A
EMAC[0]_MTXD[2]/
EMAC[1]_RGTXCTL/
EMAC[1]_RMRXD[0]/
GPMC_A[9]/
UART4_TXD
H22
EMAC[1],
GPMC, UART4
PINCNTL252
DSIS: N/A
EMAC[0]_MTXD[1]/
EMAC[1]_RGTXD[1]/
GPMC_A[8]/
UART4_RXD
H25
EMAC[1],
GPMC, UART4
PINCNTL251
DSIS: N/A
EMAC[0]_MTXD[0]/
EMAC[1]_RGRXD[3]/
GPMC_A[7]/
SPI[2]_D[0]
J24
EMAC[1],
GPMC, UART4
PINCNTL250
DSIS: N/A
EMAC[0]_MTXEN/
EMAC[1]_RGRXD[2]/
EMAC[1]_RMTXEN/
GPMC_A[15]/
UART1_RTS
J23
EMAC[0]_MTXD[6]/
EMAC[1]_RGRXD[0]/
EMAC[1]_RMTXD[0]/
GPMC_A[13]/
UART1_TXD
O
O
IPD
DVDD_GPMC
IPD
DVDD_GPMC
EMAC[1],
GPMC, UART4
PINCNTL258
DSIS: N/A
DESCRIPTION
[G]MII Transmit Data [7:0]. For 1000 EMAC GMII
operation, EMAC[0]_TXD[7:0] are used. For 10/100
EMAC MII operation, only EMAC[0]_TXD[3:0] are
used.
[G]MII Transmit Data Enable output
EMAC[0] RMII Mode
An EMAC bootmode must be selected via the BTMODE[4:0] pins. Once the EMAC bootmode is selected, the BTMODE[9:8] pins determine
the Ethernet PHY Mode Selection (for example, 01b is RMII mode). For more detailed information on EMAC bootmodes and Ethernet PHY
Mode selection, see Section 4.2.6, Ethernet PHY Mode Selection.
These pin functions are available only when RMII mode is selected.
EMAC_RMREFCLK/
TIM2_IO/
GP1[10]
J27
I/O
IPD
DVDD_GPMC
TIMER2, GP1
PINCNTL232
DSIS: PIN
RMII Reference Clock (EMAC[0] and EMAC[1] RMII
mode)
Regardless of EMAC[0] RMII Mode, the GMII_EN bit
in the MACCONTROL register, of the Control
Module, configures the RMREFCLK pin function as
an INPUT or OUTPUT clock reference. During RMII
ROM Boot, the RMREFCLK pin function is
configured as an OUTPUT clock reference (driving
50 MHz).
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
61
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-7. EMAC[0] Terminal Functions [(R)(G)MII] (continued)
SIGNAL
NAME
EMAC[0]_MRCLK/
EMAC[0]_RGTXC/
VIN[1]B_D[4]/
EMAC[0]_RMCRSDV/
SPI[3]_SCS[2]/
GP3[27]
NO.
H27
TYPE (1)
I
OTHER (2)
(3)
IPD
DVDD_GPMC
MUXED
DESCRIPTION
EMAC[0],
VIN[1]B, SPI[3],
GP3
RMII Carrier Sense input
PINCNTL239
DSIS: 0
EMAC[0]_MCRS/
EMAC[0]_RGRXD[2]/
VIN[1]B_D[2]/
EMAC[0]_RMRXD[1]/
GP3[25]
EMAC[0],
VIN[1]B, SPI[3],
GPI3
PINCNTL237
DSIS: PIN
RMII Receive Data [1:0]. For 10/100 EMAC RMII
operation, EMAC[0]_RMRXD[1:0] are used.
EMAC[0],
VIN[1]B, GP3
PINCNTL236
DSIS: PIN
R25
I
IPD
DVDD_GPMC
EMAC[0]_MCOL/
EMAC[0]_RGRXCTL/
VIN[1]B_D[1]/
EMAC[0]_RMRXD[0]/
GP3[24]
L23
I
IPD
DVDD_GPMC
EMAC[0]_MRXER/
EMAC[0]_RGTXCTL/
VIN[1]B_D[3]/
EMAC[0]_RMRXER/
GP3[26]
J26
I
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, GP3
PINCNTL238
DSIS: 0
O
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, GP3
PINCNTL241
DSIS: N/A
EMAC[0]_MRXD[1]/
EMAC[0]_RGRXD[0]/
VIN[1]B_D[6]/
EMAC[0]_RMTXD[1]/
GP3[29]
P23
EMAC[0]_MRXD[0]/
EMAC[0]_RGTXD[0]/
VIN[1]B_D[5]/
EMAC[0]_RMTXD[0]/
GP3[28]
G28
O
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, GP3
PINCNTL240
DSIS: N/A
EMAC[0]_MRXD[2]/
EMAC[0]_RGRXD[1]/
VIN[1]B_D[7]/
EMAC[0]_RMTXEN/
GP3[30]
R23
O
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, GP3
PINCNTL242
DSIS: N/A
RMII Receive Data Error input
RMII Transmit Data [7:0]. For 10/100 EMAC RMII
operation, EMAC[0]_RMTXD[1:0] are used.
RMII Transmit Data Enable output
EMAC[0] RGMII Mode
An EMAC bootmode must be selected via the BTMODE[4:0] pins. Once the EMAC bootmode is selected, the BTMODE[9:8] pins determine
the Ethernet PHY Mode Selection (for example, 10b is RGMII mode). For more detailed information on EMAC bootmodes and Ethernet
PHY Mode selection, see Section 4.2.6, Ethernet PHY Mode Selection
These pin functions are available only when RGMII mode is selected.
EMAC[0]_MTCLK/
EMAC[0]_RGRXC/
VIN[1]B_D[0]/
SPI[3]_SCS[3]/
I2C[2]_SDA/
GP3[23]
EMAC[0]_MCOL/
EMAC[0]_RGRXCTL/
VIN[1]B_D[1]/
EMAC[0]_RMRXD[0]/
GP3[24]
62
Device Pins
L24
L23
I
IPD
DVDD_GPMC
I
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, SPI[3],
I2C[2], GP3
RGMII Receive Clock
PINCNTL235
DSIS: PIN
EMAC[0],
VIN[1]B, GP3
PINCNTL236
DSIS: PIN
RGMII Receive Control
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-7. EMAC[0] Terminal Functions [(R)(G)MII] (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
EMAC[0]_MRXD[4]/
EMAC[0]_RGRXD[3]/
GPMC_A[1]/
UART5_TXD
T23
I
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART5
PINCNTL244
DSIS: PIN
EMAC[0]_MCRS/
EMAC[0]_RGRXD[2]/
VIN[1]B_D[2]/
EMAC[0]_RMRXD[1]/
GP3[25]
R25
I
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, GP3
PINCNTL237
DSIS: PIN
EMAC[0],
VIN[1]B, GP3
PINCNTL242
DSIS: PIN
EMAC[0],
VIN[1]B, GP3
PINCNTL241
DSIS: PIN
EMAC[0]_MRXD[2]/
EMAC[0]_RGRXD[1]/
VIN[1]B_D[7]/
EMAC[0]_RMTXEN/
GP3[30]
R23
I
IPD
DVDD_GPMC
EMAC[0]_MRXD[1]/
EMAC[0]_RGRXD[0]/
VIN[1]B_D[6]/
EMAC[0]_RMTXD[1]/
GP3[29]
P23
I
IPD
DVDD_GPMC
O
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, GP3
PINCNTL238
DSIS: N/A
EMAC[0]_MRCLK/
EMAC[0]_RGTXC/
VIN[1]B_D[4]/
EMAC[0]_RMCRSDV/
SPI[3]_SCS[2]/
GP3[27]
H27
J26
O
IPD
DVDD_GPMC
EMAC[0]_MRXD[5]/
EMAC[0]_RGTXD[3]/
GPMC_A[2]/
UART5_CTS
H26
O
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART5
PINCNTL245
DSIS: N/A
EMAC[0]_MRXD[6]/
EMAC[0]_RGTXD[2]/
GPMC_A[3]/
UART5_RTS
F28
O
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART5
PINCNTL246
DSIS: N/A
EMAC[0],
GPMC, SPI[2]
PINCNTL247
DSIS: N/A
EMAC[0],
VIN[1]B, GP3
PINCNTL240
DSIS: N/A
G27
O
IPD
DVDD_GPMC
EMAC[0]_MRXD[0]/
EMAC[0]_RGTXD[0]/
VIN[1]B_D[5]/
EMAC[0]_RMTXD[0]/
GP3[28]
G28
O
IPD
DVDD_GPMC
RGMII Receive Data [3:0]
EMAC[0],
VIN[1]B, SPI[3],
GP3
RGMII Transmit Clock
PINCNTL239
DSIS: N/A
EMAC[0]_MRXER/
EMAC[0]_RGTXCTL/
VIN[1]B_D[3]/
EMAC[0]_RMRXER/
GP3[26]
EMAC[0]_MRXD[7]/
EMAC[0]_RGTXD[1]/
GPMC_A[4]/
SPI[2]_SCS[3]
DESCRIPTION
RGMII Transmit Enable
RGMII Transmit Data [3:0]
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
63
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-8. EMAC[1] Terminal Functions [(R)(G)MII]
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
EMAC[1] (G)MII Mode
An EMAC bootmode must be selected via the BTMODE[4:0] pins. Once the EMAC bootmode is selected, the BTMODE[9:8] pins determine
the Ethernet PHY Mode Selection (for example, 00b is MII mode). For more detailed information on EMAC bootmodes and Ethernet PHY
Mode selection, see Section 4.2.6, Ethernet PHY Mode Selection.
These pin functions are available only when GMII and MII modes are selected.
VOUT[1]_HSYNC/
EMAC[1]_MCOL/
VIN[1]A_VSYNC/
SPI[3]_D[1]/
UART3_RTS/
GP2[29]
AC24
I
IPD
DVDD
VOUT[1],
VIN[1]A, SPI[3],
UART3, GP2
[G]MII Collision Detect (Sense) input
PINCNTL205
DSIS: 0
VOUT[1],
VIN[1]A, SPI[3],
UART3, GP2
[G]MII Carrier Sense input
PINCNTL206
DSIS: 0
VOUT[1]_VSYNC/
EMAC[1]_MCRS/
VIN[1]A_FLD/
VIN[1]A_DE/
SPI[3]_D[0]/
UART3_CTS/
GP2[30]
AA23
I
IPD
DVDD
VOUT[1]_G_Y_YC[6]/
EMAC[1]_GMTCLK/
VIN[1]A_D[11]/
GP3[10]
AH27
O
IPD
DVDD
VOUT[1],
VIN[1]A, GP3
PINCNTL218
DSIS: N/A
GMII Source Synchronous Transmit Clock
I
IPD
DVDD
VOUT[1],
VIN[1]A,
UART4, GP3
PINCNTL208
DSIS: 0
[G]MII Receive Clock
VOUT[1]_B_CB_C[3]/
EMAC[1]_MRCLK/
VIN[1]A_D[0]/
UART4_CTS/
GP3[0]
(1)
(2)
(3)
64
AH25
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and the Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-8. EMAC[1] Terminal Functions [(R)(G)MII] (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
VOUT[1]_G_Y_YC[4]/
EMAC[1]_MRXD[7]/
VIN[1]A_D[9]/
GP3[8]
W22
VOUT[1],
VIN[1]A, GP3
PINCNTL216
DSIS: PIN
VOUT[1]_G_Y_YC[3]/
EMAC[1]_MRXD[6]/
VIN[1]A_D[8]/
GP3[7]
Y23
VOUT[1],
VIN[1]A, GP3
PINCNTL215
DSIS: PIN
AA24
VOUT[1],
VIN[1]A, I2C[3],
GP3
PINCNTL214
DSIS: PIN
AH26
VOUT[1],
VIN[1]A, I2C[3],
GP3
PINCNTL213
DSIS: PIN
VOUT[1]_B_CB_C[9]/
EMAC[1]_MRXD[5]/
VIN[1]A_D[6]/
I2C[3]_SDA/
GP3[6]
VOUT[1]_B_CB_C[8]/
EMAC[1]_MRXD[4]/
VIN[1]A_D[5]/
I2C[3]_SCL/
GP3[5]
VOUT[1]_B_CB_C[7]/
EMAC[1]_MRXD[3]/
VIN[1]A_D[4]/
UART3_TXD/
GP3[4]
IPD
DVDD
AC25
VOUT[1],
VIN[1]A,
UART3, GP3
PINCNTL212
DSIS: PIN
AD25
VOUT[1],
VIN[1]A,
UART3, GP3
PINCNTL211
DSIS: PIN
AF25
VOUT[1],
VIN[1]A,
UART4, GP3
PINCNTL210
DSIS: PIN
VOUT[1]_B_CB_C[4]/
EMAC[1]_MRXD[0]/
VIN[1]A_D[1]/
UART4_RXD/
GP3[1]
AG25
VOUT[1],
VIN[1]A,
UART4, GP3
PINCNTL209
DSIS: PIN
VOUT[1]_G_Y_YC[5]/
EMAC[1]_MRXDV/
VIN[1]A_D[10]/
GP3[9]
AG26
VOUT[1]_B_CB_C[6]/
EMAC[1]_MRXD[2]/
VIN[1]A_D[3]/
UART3_RXD/
GP3[3]
VOUT[1]_B_CB_C[5]/
EMAC[1]_MRXD[1]/
VIN[1]A_D[2]/
UART4_TXD/
GP3[2]
VOUT[1]_AVID/
EMAC[1]_MRXER/
VIN[1]A_CLK/
UART4_RTS/
TIM6_IO/
GP2[31]
VOUT[1]_CLK/
EMAC[1]_MTCLK/
VIN[1]A_HSYNC/
GP2[28]
I
Y22
AE24
DESCRIPTION
[G]MII Receive Data [7:0]. For 1000 EMAC GMII
operation, EMAC[0]_RXD[7:0] are used. For 10/100
EMAC MII operation, only EMAC[0]_RXD[3:0] are
used.
IPD
DVDD
VOUT[1],
VIN[1]A, GP3
PINCNTL217
DSIS: 0
[G]MII Receive Data Valid input
I
IPD
DVDD
VOUT[1],
VIN[1]A,
UART4, TIMER
6, GP2
PINCNTL207
DSIS: 0
[G]MII Receive Data Error input
I
IPD
DVDD
VOUT[1],
VIN[1]A, GP2
PINCNTL204
DSIS: 0
I
[G]MII Transmit Clock input
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
65
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-8. EMAC[1] Terminal Functions [(R)(G)MII] (continued)
SIGNAL
NAME
VOUT[1]_R_CR[8]/
EMAC[1]_MTXD[7]/
VIN[1]A_D[19]/
UART5_RXD/
GP3[18]
VOUT[1]_R_CR[7]/
EMAC[1]_MTXD[6]/
VIN[1]A_D[18]/
SPI[3]_D[0]/
GP3[17]
VOUT[1]_R_CR[6]/
EMAC[1]_MTXD[5]/
VIN[1]A_D[17]/
SPI[3]_D[1]/
GP3[16]
NO.
V22
AA25
VOUT[1],
VIN[1]A, SPI[3],
GP3
PINCNTL224
DSIS: N/A
AG27
VOUT[1]_R_CR[9]/
EMAC[1]_MTXEN/
VIN[1]A_D[20]/
UART5_TXD/
GP3[19]
MUXED
VOUT[1],
VIN[1]A, SPI[3],
GP3
PINCNTL225
DSIS: N/A
VOUT[1]_R_CR[4]/
EMAC]1]_MTXD[3]/
VIN]1]A_D[15]/
SPI[3]_SCS[1]/
GP3[14]
VOUT[1]_G_Y_YC[7]/
EMAC[1]_MTXD[0]/
VIN[1]A_D[12]/
GP3[11]
(3)
W23
AC26
VOUT[1]_G_Y_YC[8]/
EMAC[1]_MTXD[1]/
VIN[1]A_D[13]/
GP3[12]
OTHER (2)
VOUT[1],
VIN[1]A,
UART5, GP3
PINCNTL226
DSIS: N/A
VOUT[1]_R_CR[5]/
EMAC[1]_MTXD[4]/
VIN[1]A_D[16]/
SPI[3]_SCLK/
GP3[15]
VOUT[1]_G_Y_YC[9]/
EMAC[1]_MTXD[2]/
VIN[1]A_D[14]/
GP3[13]
TYPE (1)
O
IPD
DVDD
VOUT[1],
VIN[1]A, SPI[3],
[G]MII Transmit Data [7:0]. For 1000 EMAC GMII
GP3
operation, EMAC[0]_TXD[7:0] are used. For 10/100
PINCNTL223
EMAC MII operation, only EMAC[0]_TXD[3:0] are
DSIS: N/A
used.
VOUT[1],
VIN[1]A, SPI[3],
GP3
PINCNTL222
DSIS: N/A
AD26
VOUT[1],
VIN[1]A, GP3
PINCNTL221
DSIS: N/A
AE26
VOUT[1],
VIN[1]A, GP3
PINCNTL220
DSIS: N/A
AF26
VOUT[1],
VIN[1]A, GP3
PINCNTL219
DSIS: N/A
Y24
VOUT[1],
VIN[1]A,
UART5, GP3
PINCNTL227
DSIS: N/A
O
IPD
DVDD
DESCRIPTION
[G]MII Transmit Data Enable output
EMAC[1] RMII Mode
An EMAC bootmode must be selected via the BTMODE[4:0] pins. Once the EMAC bootmode is selected, the BTMODE[9:8] pins determine
the Ethernet PHY Mode Selection (for example, 01b is RMII mode). For more detailed information on EMAC bootmodes and Ethernet PHY
Mode selection, see Section 4.2.6, Ethernet PHY Mode Selection.
These pin functions are available only when RMII mode is selected.
EMAC_RMREFCLK/
TIM2_IO/
GP1[10]
66
Device Pins
J27
I/O
IPD
DVDD_GPMC
TIMER2, GP1
PINCNTL232
DSIS: PIN
RMII Reference Clock (EMAC[0] and EMAC[1] RMII
mode)
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-8. EMAC[1] Terminal Functions [(R)(G)MII] (continued)
SIGNAL
NAME
VIN[0]A_D[20]/
CAM_D[12]/
EMAC[1]_RMCRSDV/
SPI[3]_SCS[0]/
GP0[14]
EMAC[0]_MTXD[5]/
EMAC[1]_RGTXC/
EMAC[1]_RMCRSDV/
GPMC_A[12]/
UART1_RXD
VIN[0]A_D[18]/
CAM_D[10]/
EMAC[1]_RMRXD[1]/
I2C[3]_SCL/
GP0[12]
EMAC[0]_MTXD[3]/
EMAC[1]_RGTXD[0]/
EMAC[1]_RMRXD[1]/
GPMC_A[10]/
UART4_CTS
VIN[0]A_D[19]/
CAM_D[11]/
EMAC[1]_RMRXD[0]/
I2C[3]_SDA/
GP0[13]
EMAC[0]_MTXD[2]/
EMAC[1]_RGTXCTL/
EMAC[1]_RMRXD[0]/
GPMC_A[9]/
UART4_TXD
VIN[0]A_D[17]/
CAM_D[9]/
EMAC[1]_RMRXER/
GP0[11]
EMAC[0]_MTXD[4]/
EMAC[1]_RGTXD[2]/
EMAC[1]_RMRXER/
GPMC_A[11]/
UART4_RTS
NO.
AC17
F27
AF20
H23
AF21
H22
AB21
G23
TYPE (1)
I
I
I
I
I
I
I
I
OTHER (2)
(3)
MUXED
IPD
DVDD_C
VIN[0]A,
CAMERA_I/F,
SPI[3], GP0
PINCNTL160
DSIS: 0
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1],
GPMC, UART1
PINCNTL255
DSIS: 0
MM: MUX0
IPU
DVDD_C
VIN[0]A,
CAMERA_I/F,
I2C[3], GP0
PINCNTL158
DSIS: PIN
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1],
GPMC, UART4
PINCNTL253
DSIS: PIN
MM: MUX0
IPU
DVDD_C
VIN[0]A,
CAMERA_I/F,
I2C[3], GP0
PINCNTL159
DSIS: PIN
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1],
GPMC, UART4
PINCNTL252
DSIS: PIN
MM: MUX0
IPD
DVDD_C
VIN[0]A,
CAMERA_I/F,
SPI[3], GP0
PINCNTL157
DSIS: 0
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1],
GPMC, UART1
PINCNTL254
DSIS: 0
MM: MUX0
DESCRIPTION
RMII Carrier Sense input
RMII Receive Data [1:0].
RMII Receive Data Error input
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
67
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-8. EMAC[1] Terminal Functions [(R)(G)MII] (continued)
SIGNAL
NAME
VIN[0]A_D[22]/
CAM_D[14]/
EMAC[1]_RMTXD[1]/
SPI[3]_D[1]/
GP0[16]
EMAC[0]_MTXD[7]/
EMAC[1]_RGTXD[3]/
EMAC[1]_RMTXD[1]/
GPMC_A[14]/
UART1_CTS
VIN[0]A_D[21]/
CAM_D[13]/
EMAC[1]_RMTXD[0]/
SPI[3]_SCLK/
GP0[15]
EMAC[0]_MTXD[6]/
EMAC[1]_RGRXD[0]/
EMAC[1]_RMTXD[0]/
GPMC_A[13]/
UART1_TXD
VIN[0]A_D[23]/
CAM_D[15]/
EMAC[1]_RMTXEN/
SPI[3]_D[0]/
GP0[17]
EMAC[0]_MTXEN/
EMAC[1]_RGRXD[2]/
EMAC[1]_RMTXEN/
GPMC_A[15]/
UART1_RTS
NO.
AC21
H24
AE18
J22
AC16
J23
TYPE (1)
O
O
O
O
O
O
OTHER (2)
(3)
MUXED
IPD
DVDD_C
VIN[0]A,
CAMERA_I/F,
SPI[3], GP0
PINCNTL162
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART1
PINCNTL257
DSIS: N/A
MM: MUX0
IPD
DVDD_C
VIN[0]A
CAMERA_I/F,
SPI[3], GP0
PINCNTL161
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1],
GPMC, UART1
PINCNTL256
DSIS: N/A
MM: MUX0
IPD
DVDD_C
VIN[0]A,
CAMERA_I/F,
SPI[3], GP0
PINCNTL163
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1],
GPMC, UART1
PINCNTL258
DSIS: N/A
MM: MUX0
DESCRIPTION
RMII Transmit Data [1:0].
RMII Transmit Data Enable output
EMAC[1] RGMII MODE
An EMAC bootmode must be selected via the BTMODE[4:0] pins. Once the EMAC bootmode is selected, the BTMODE[9:8] pins determine
the Ethernet PHY Mode Selection (for example, 10b is RGMII mode). For more detailed information on EMAC bootmodes and Ethernet
PHY Mode selection, see Section 4.2.6, Ethernet PHY Mode Selection
These pin functions are available only when RGMII mode is selected.
EMAC[0]_GMTCLK/
EMAC[1]_RGRXC/
GPMC_A[6]/
SPI[2]_D[1]
EMAC[0]_MRXD[3]/
EMAC[1]_RGRXCTL/
GPMC_A[27]/
GPMC_A[26]/
GPMC_A[0]/
UART5_RXD
68
Device Pins
K23
J25
I
IPD
DVDD_GPMC
EMAC[0],
GPMC, SPI[2]
PINCNTL249
DSIS: PIN
RGMII Receive Clock
I
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART5
PINCNTL243
DSIS: PIN
RGMII Receive Control
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-8. EMAC[1] Terminal Functions [(R)(G)MII] (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
EMAC[0]_MTXD[0]/
EMAC[1]_RGRXD[3]/
GPMC_A[7]/
SPI[2]_D[0]
J24
I
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART4
PINCNTL250
DSIS: PIN
EMAC[0]_MTXEN/
EMAC[1]_RGRXD[2]/
EMAC[1]_RMTXEN/
GPMC_A[15]/
UART1_RTS
J23
I
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART4
PINCNTL258
DSIS: PIN
I
IPD
DVDD_GPMC
EMAC[0],
GPMC, SPI[2]
PINCNTL248
DSIS: PIN
EMAC[0],
GPMC, UART1
PINCNTL256
DSIS: PIN
EMAC[0]_MRXDV/
EMAC[1]_RGRXD[1]/
GPMC_A[5]/
SPI[2]_SCLK
K22
DESCRIPTION
RGMII Receive Data [3:0]
EMAC[0]_MTXD[6]/
EMAC[1]_RGRXD[0]/
EMAC[1]_RMTXD[0]/
GPMC_A[13]/
UART1_TXD
J22
I
IPD
DVDD_GPMC
EMAC[0]_MTXD[5]/
EMAC[1]_RGTXC/
EMAC[1]_RMCRSDV/
GPMC_A[12]/
UART1_RXD
F27
O
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART1
PINCNTL255
DSIS: N/A
RGMII Transmit Clock
EMAC[0]_MTXD[2]/
EMAC[1]_RGTXCTL/
EMAC[1]_RMRXD[0]/
GPMC_A[9]/
UART4_TXD
H22
O
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART4
PINCNTL252
DSIS: N/A
RGMII Transmit Enable
O
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART1
PINCNTL257
DSIS: N/A
O
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART4
PINCNTL254
DSIS: N/A
O
IPD
DVDD_GPMC
EMAC[0],
GPMC, UART4
PINCNTL251
DSIS: N/A
O
IPD
DVDD_GPMC
EMAC[0],
EMAC[1],
GPMC, UART4
PINCNTL253
DSIS: N/A
EMAC[0]_MTXD[7]/
EMAC[1]_RGTXD[3]/
EMAC[1]_RMTXD[1]/
GPMC_A[14]/
UART1_CTS
EMAC[0]_MTXD[4]/
EMAC[1]_RGTXD[2]/
EMAC[1]_RMRXER/
GPMC_A[11]/
UART4_RTS
EMAC[0]_MTXD[1]/
EMAC[1]_RGTXD[1]/
GPMC_A[8]/
UART4_RXD
EMAC[0]_MTXD[3]/
EMAC[1]_RGTXD[0]/
EMAC[1]_RMRXD[1]/
GPMC_A[10]/
UART4_CTS
H24
G23
H25
H23
RGMII Transmit Data [3:0]
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
69
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-9. MDIO Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
MDIO
MDCLK/
GP1[11]
H28
O
IPU
DVDD_GPMC
GP1
PINCNTL233
DSIS: N/A
Management Data Serial Clock output
MDIO/
GP1[12]
P24
I/O
IPU
DVDD_GPMC
GP1
PINCNTL234
DSIS: 1
Management Data I/O
(1)
(2)
(3)
70
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
3.2.7
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
General-Purpose Input/Outputs (GPIOs)
Table 3-10. GP0 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
GPIO0
Note: General-Purpose Input/Output (I/O) pins can also serve as external interrupt inputs.
UART2_TXD/
GP0[31]
U3
I/O
IPD
DVDD
UART2
PINCNTL61
DSIS: PIN
General-Purpose Input/Output (I/O) 0 [GP0] pin 31
TCLKIN/
GP0[30]
T2
I/O
IPD
DVDD
TCLKIN
PINCNTL60
DSIS: PIN
General-Purpose Input/Output (I/O) 0 [GP0] pin 30
UART2_RXD/
GP0[29]
U4
I/O
IPD
DVDD
UART2
PINCNTL59
DSIS: PIN
General-Purpose Input/Output (I/O) 0 [GP0] pin 29
I/O
IPD
DVDD
MCA[5], MCA[4],
TIMER7
PINCNTL58
DSIS: PIN
MM: MUX1
MCA[5]_AXR[1]/
MCA[4]_AXR[3]/
TIM7_IO/
GP0[28]
VOUT[1]_FLD/
CAM_FLD/
CAM_WE/
GPMC_A[11]/
UART2_CTS/
GP0[28]
MCA[5]_AXR[0]/
MCA[4]_AXR[2]/
GP0[27]
VOUT[1]_B_CB_C[0]/
CAM_VS/
GPMC_A[10]/
UART2_TXD/
GP0[27]
MCA[5]_AFSX/
GP0[26]
VOUT[1]_B_CB_C[1]/
CAM_HS/
GPMC_A[9]/
UART2_RXD/
GP0[26]
MCA[5]_ACLKX/
GP0[25]
VOUT[1]_R_CR[0]/
CAM_D[0]/
GPMC_A[8]/
UART4_RTS/
GP0[25]
(1)
(2)
(3)
L6
AB23
I/O
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, UART2
PINCNTL174
DSIS: PIN
MM: MUX0
L7
I/O
IPD
DVDD
MCA[5], MCA[4]
PINCNTL57
DSIS: PIN
MM: MUX1
I/O
IPU
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, UART2
PINCNTL173
DSIS: PIN
MM: MUX0
I/O
IPD
DVDD
MCA[5]
PINCNTL56
DSIS: PIN
MM: MUX1
AD23
H5
AE23
I/O
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, UART2
PINCNTL172
DSIS: PIN
MM: MUX0
J3
I/O
IPD
DVDD
MCA[5]
PINCNTL55
DSIS: PIN
MM: MUX1
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, UART4
PINCNTL171
DSIS: PIN
MM: MUX0
AA22
I/O
General-Purpose Input/Output (I/O) 0 [GP0] pin 28
General-Purpose Input/Output (I/O) 0 [GP0] pin 27
General-Purpose Input/Output (I/O) 0 [GP0] pin 26
General-Purpose Input/Output (I/O) 0 [GP0] pin 25
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
71
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-10. GP0 Terminal Functions (continued)
SIGNAL
NAME
MCA[4]_AXR[1]/
TIM6_IO/
GP0[24]
VOUT[1]_R_CR[1]/
CAM_D[1]/
GPMC_A[7]/
UART4_CTS/
GP0[24]
MCA[4]_AXR[0]/
GP0[23]
VOUT[1]_G_Y_YC[0]/
CAM_D[2]/
GPMC_A[6]/
UART4_TXD/
GP0[23]
MCA[4]_AFSX/
GP0[22]
VOUT[1]_G_Y_YC[1]/
CAM_D[3]/
GPMC_A[5]/
UART4_RXD/
GP0[22]
MCA[4]_ACLKX/
GP0[21]
VIN[0]B_FLD/
CAM_D[4]/
GP0[21]
MCA[3]_AXR[2]/
MCA[1]_AXR[8]/
GP0[20]
VIN[0]A_FLD/
CAM_D[5]/
GP0[20]
MCA[3]_AXR[1]/
TIM5_IO/
GP0[19]
VIN[0]B_DE/
CAM_D[6]/
GP0[19]
72
Device Pins
NO.
J4
AC19
H6
TYPE (1)
OTHER (2)
(3)
MUXED
IPD
DVDD
MCA[4], TIMER6
PINCNTL54
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, UART4
PINCNTL170
DSIS: PIN
MM: MUX0
I/O
IPD
DVDD
MCA[4]
PINCNTL53
DSIS: PIN
MM: MUX1
I/O
AC18
I/O
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, UART4
PINCNTL169
DSIS: PIN
MM: MUX0
H3
I/O
IPD
DVDD
MCA[4]
PINCNTL52
DSIS: PIN
MM: MUX1
AD18
I/O
IPU
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, UART4
PINCNTL168
DSIS: PIN
MM: MUX0
K7
I/O
IPD
DVDD
MCA[4]
PINCNTL51
DSIS: PIN
MM: MUX1
AD17
I/O
IPU
DVDD_C
VIN[0]B,
CAMERA_I/F
PINCNTL167
DSIS: PIN
MM: MUX0
F2
I/O
IPD
DVDD
MCA[3], MCA[1]
PINCNTL49
DSIS: PIN
MM: MUX1
I/O
IPU
DVDD_C
VIN[0]A,
CAMERA_I/F
PINCNTL166
DSIS: PIN
MM: MUX0
I/O
IPD
DVDD
MCA[3], TIMER5
PINCNTL48
DSIS: PIN
MM: MUX1
IPU
DVDD_C
VIN[0]B,
CAMERA_I/F
PINCNTL165
DSIS: PIN
MM: MUX0
AC22
G2
AC15
I/O
DESCRIPTION
General-Purpose Input/Output (I/O) 0 [GP0] pin 24
General-Purpose Input/Output (I/O) 0 [GP0] pin 23
General-Purpose Input/Output (I/O) 0 [GP0] pin 22
General-Purpose Input/Output (I/O) 0 [GP0] pin 21
General-Purpose Input/Output (I/O) 0 [GP0] pin 20
General-Purpose Input/Output (I/O) 0 [GP0] pin 19
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-10. GP0 Terminal Functions (continued)
SIGNAL
NAME
MCA[3]_AXR[0]/
TIM4_IO/
GP0[18]
VIN[0]A_DE/
CAM_D[7]/
GP0[18]
MCA[3]_AFSX/
GP0[17]
VIN[0]A_D[23]/
CAM_D[15]/
EMAC[1]_RMTXEN/
SPI[3]_D[0]/
GP0[17]
MCA[3]_ACLKX/
GP0[16]
VIN[0]A_D[22]/
CAM_D[14]/
EMAC[1]_RMTXD[1]/
SPI[3]_D[1]/
GP0[16]
MCA[2]_AXR[3]/
MCA[1]_AXR[7]/
TIM3_IO/
GP0[15]
VIN[0]A_D[21]/
CAM_D[13]/
EMAC[1]_RMTXD[0]/
SPI[3]_SCLK/
GP0[15]
MCA[2]_AXR[2]/
MCA[1]_AXR[6]/
TIM2_IO/
GP0[14]
VIN[0]A_D[20]/
CAM_D[12]/
EMAC[1]_RMCRSDV/
SPI[3]_SCS[0]/
GP0[14]
NO.
G1
TYPE (1)
OTHER (2)
I/O
(3)
MUXED
IPD
DVDD
MCA[3], TIMER4
PINCNTL47
DSIS: PIN
MM: MUX1
AB17
I/O
IPU
DVDD_C
VIN[0]A,
CAMERA_I/F
PINCNTL164
DSIS: PIN
MM: MUX0
H4
I/O
IPD
DVDD
MCA[3]
PINCNTL46
DSIS: PIN
MM: MUX1
AC16
I/O
IPD
DVDD_C
VIN[0]A,
CAMERA_I/F,
EMAC[1]_RM,
SPI[3]
PINCNTL163
DSIS: PIN
MM: MUX0
G6
I/O
IPD
DVDD
MCA[3]
PINCNTL45
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD_C
VIN[0]A,
CAMERA_I/F,
EMAC[1]_RM,
SPI[3]
PINCNTL162
DSIS: PIN
MM: MUX0
I/O
IPD
DVDD
MCA[2], MCA[1],
TIMER3
PINCNTL44
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD_C
VIN[0]A,
CAMERA_I/F,
EMAC[1]_RM,
SPI[3]
PINCNTL161
DSIS: PIN
MM: MUX0
I/O
IPD
DVDD
MCA[2], MCA[1],
TIMER2
PINCNTL43
DSIS: PIN
MM: MUX1
IPD
DVDD_C
VIN[0]A,
CAMERA_I/F,
EMAC[1]_RM,
SPI[3]
PINCNTL160
DSIS: PIN
MM: MUX0
AC21
H2
AE18
V5
AC17
I/O
DESCRIPTION
General-Purpose Input/Output (I/O) 0 [GP0] pin 18
General-Purpose Input/Output (I/O) 0 [GP0] pin 17
General-Purpose Input/Output (I/O) 0 [GP0] pin 16
General-Purpose Input/Output (I/O) 0 [GP0] pin 15
General-Purpose Input/Output (I/O) 0 [GP0] pin 14
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
73
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-10. GP0 Terminal Functions (continued)
SIGNAL
NAME
MCA[2]_AXR[1]/
SD0_DAT[7]/
UART5_TXD/
GP0[13]
VIN[0]A_D[19]/
CAM_D[11]/
EMAC[1]_RMRXD[0]/
I2C[3]_SDA/
GP0[13]
MCA[2]_AXR[0]/
SD0_DAT[6]/
UART5_RXD/
GP0[12]
NO.
V6
AF21
N2
TYPE (1)
OTHER (2)
(3)
MUXED
IPU
DVDD
MCA[2], SD0,
UART5
PINCNTL42
DSIS: PIN
MM: MUX1
I/O
IPU
DVDD_C
VIN[0]A,
CAMERA_I/F,
EMAC[1]_RM,
I2C[3]
PINCNTL159
DSIS: PIN
MM: MUX0
I/O
IPU
DVDD
MCA[2], SD0,
UART5
PINCNTL41
DSIS: PIN
MM: MUX1
I/O
VIN[0]A_D[18]/
CAM_D[10]/
EMAC[1]_RMRXD[1]/
I2C[3]_SCL/
GP0[12]
AF20
I/O
IPU
DVDD_C
VIN[0]A,
CAMERA_I/F,
EMAC[1]_RM,
I2C[3]
PINCNTL158
DSIS: PIN
MM: MUX0
MCA[2]_AFSX/
GP0[11]
AA5
I/O
IPU
DVDD
MCA[2]
PINCNTL40
DSIS: PIN
MM: MUX1
VIN[0]A_D[17]/
CAM_D[9]/
EMAC[1]_RMRXER/
GP0[11]
MCA[2]_ACLKX/
GP0[10]
VIN[0]A_D[16]/
CAM_D[8]/
I2C[2]_SCL/
GP0[10]
AUD_CLKIN2/
MCA[0]_AXR[9]/
MCA[2]_AHCLKX/
MCA[5]_AHCLKX/
EDMA_EVT2/
TIM3_IO/
GP0[9]
General-Purpose Input/Output (I/O) 0 [GP0] pin 12
AB21
I/O
IPD
DVDD_C
U6
I/O
IPU
DVDD
MCA[2]
PINCNTL39
DSIS: PIN
MM: MUX1
IPU
DVDD_C
VIN[0]A,
CAMERA_I/F,
I2C[2]
PINCNTL156
DSIS: PIN
MM: MUX0
IPD
DVDD
AUD_CLKIN2,
MCA[0], MCA[2],
MCA[5], EDMA,
TIMER3
PINCNTL16
DSIS: PIN
General-Purpose Input/Output (I/O) 0 [GP0] pin 9
General-Purpose Input/Output (I/O) 0 [GP0] pin 8
General-Purpose Input/Output (I/O) 0 [GP0] pin 7
AA21
H1
I/O
I/O
R5
I/O
IPD
DVDD
AUD_CLKIN1,
MCA[0], MCA[1],
MCA[4], EDMA,
TIMER2
PINCNTL15
DSIS: PIN
USB0_DRVVBUS/
GP0[7]
AF11
I/O
IPD
DVDD
USB0
PINCNTL270
DSIS: PIN
Device Pins
General-Purpose Input/Output (I/O) 0 [GP0] pin 13
VIN[0]A,
CAMERA_I/F,
EMAC[1]_RM
PINCNTL157
DSIS: PIN
MM: MUX0
AUD_CLKIN1/
MCA[0]_AXR[8]/
MCA[1]_AHCLKX/
MCA[4]_AHCLKX/
EDMA_EVT3/
TIM2_IO/
GP0[8]
74
DESCRIPTION
General-Purpose Input/Output (I/O) 0 [GP0] pin 11
General-Purpose Input/Output (I/O) 0 [GP0] pin 10
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-10. GP0 Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
SD0_DAT[3]/
SD1_DAT[7]/
GP0[6]
Y4
I/O
IPU
DVDD_SD
SD0, SD1
PINCNTL13
DSIS: PIN
General-Purpose Input/Output (I/O) 0 [GP0] pin 6
SD0_DAT[2]_SDRW/
SD1_DAT[6]/
GP0[5]
Y3
I/O
IPU
DVDD_SD
SD0, SD1
PINCNTL12
DSIS: PIN
General-Purpose Input/Output (I/O) 0 [GP0] pin 5
SD0_DAT[1]_SDIRQ/
SD1_DAT[5]/
GP0[4]
Y5
I/O
IPU
DVDD_SD
SD0, SD1
PINCNTL11
DSIS: PIN
General-Purpose Input/Output (I/O) 0 [GP0] pin 4
SD0_DAT[0]/
SD1_DAT[4]/
GP0[3]
R7
I/O
IPU
DVDD_SD
SD0, SD1
PINCNTL10
DSIS: PIN
General-Purpose Input/Output (I/O) 0 [GP0] pin 3
SD0_CMD/
SD1_CMD/
GP0[2]
N1
I/O
IPU
DVDD_SD
SD0, SD1
PINCNTL9
DSIS: PIN
General-Purpose Input/Output (I/O) 0 [GP0] pin 2
SD0_CLK/
GP0[1]
Y6
I/O
IPU
DVDD_SD
SD0
PINCNTL8
DSIS: PIN
General-Purpose Input/Output (I/O) 0 [GP0] pin 1
SD1_CMD/
GP0[0]
P2
I/O
IPU
DVDD_SD
SD1
PINCNTL2
DSIS: PIN
General-Purpose Input/Output (I/O) 0 [GP0] pin 0
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
75
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-11. GP1 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
GPIO1
Note: General-Purpose Input/Output (I/O) pins can also serve as external interrupt inputs.
GPMC_WAIT[0]/
GPMC_A[26]/
EDMA_EVT0/
GP1[31]
W28
I/O
IPU
DVDD_GP
MC
GPMC, EDMA
PINCNTL133
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 31
GPMC_BE[1]/
GPMC_A[24]/
EDMA_EVT1/
TIM7_IO/
GP1[30]
V28
I/O
IPD
DVDD_GP
MC
GPMC, EDMA,
TIMER7
PINCNTL132
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 30
GPMC, EDMA,
TIMER6
PINCNTL131
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 29
GPMC, TIMER5
PINCNTL128
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 28
GPMC_BE[0]_CLE/
GPMC_A[25]/
EDMA_EVT2/
TIM6_IO/
GP1[29]
U27
I/O
IPD
DVDD_GP
MC
GPMC_ADV_ALE/
GPMC_CS[6]/
TIM5_IO/
GP1[28]
M26
I/O
IPU
DVDD_GP
MC
GPMC_CLK/
GPMC_CS[5]/
GPMC_WAIT[1]/
CLKOUT1/
EDMA_EVT3/
TIM4_IO/
GP1[27]
R26
I/O
IPU
DVDD_GP
MC
I/O
IPU
DVDD
SPI[1]
PINCNTL88
DSIS: PIN
MM: MUX1
GPMC, VIN[1]B,
SPI[2]
PINCNTL125
DSIS: PIN
MM: MUX0
SPI[1]_D[0]/
GP1[26]
AA6
GPMC, CLKOUT1,
EDMA, TIMER4
General-Purpose Input/Output (I/O) 1 [GP1] pin 27
PINCNTL127
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 26
GPMC_CS[3]/
VIN[1]B_CLK/
SPI[2]_SCS[0]/
GP1[26]
P26
I/O
IPU
DVDD_GP
MC
GPMC_CS[2]/
GPMC_A[24]/
GP1[25]
M25
I/O
IPU
DVDD_GP
MC
GPMC
PINCNTL124
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 25
GPMC_CS[1]/
GPMC_A[25]/
GP1[24]
K28
I/O
IPU
DVDD_GP
MC
GPMC
PINCNTL123
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 24
GPMC_CS[0]/
GP1[23]
T28
I/O
IPU
DVDD_GP
MC
GPMC
PINCNTL122
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 23
I/O
IPU
DVDD_GP
MC
SD2, GPMC,
EDMA, TIMER7
PINCNTL116
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 22
SD2_DAT[4]/
GPMC_A[27]/
GPMC_A[23]/
GPMC_CS[7]/
EDMA_EVT0/
TIM7_IO/
GP1[22]
(1)
(2)
(3)
76
R24
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-11. GP1 Terminal Functions (continued)
SIGNAL
NAME
NO.
SD2_DAT[5]/
GPMC_A[26]/
GPMC_A[22]/
TIM6_IO/
GP1[21]
P22
SD2_DAT[6]/
GPMC_A[25]/
GPMC_A[21]/
UART2_TXD/
GP1[20]
N23
TYPE (1)
OTHER (2)
(3)
MUXED
I/O
IPU
DVDD_GP
MC
SD2, GPMC,
TIMER6
PINCNTL115
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 21
I/O
IPU
DVDD_GP
MC
SD2, GPMC,
UART2
PINCNTL114
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 20
SD2, GPMC,
UART2
PINCNTL113
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 19
SD2_DAT[7]/
GPMC_A[24]/
GPMC_A[20]/
UART2_RXD/
GP1[19]
L25
I/O
IPU
DVDD_GP
MC
SPI[1]_D[1]/
GP1[18]
AA3
I/O
IPU
DVDD
SPI[1]
PINCNTL87
DSIS: PIN
MM: MUX1
GPMC, SPI[2],
HDMI, TIMER5
PINCNTL112
DSIS: PIN
MM: MUX0
GPMC_A[23]/
SPI[2]_SCLK/
HDMI_HPDET/
TIM5_IO/
GP1[18]
AA26
I/O
IPD
DVDD_GP
MC
SPI[1]_SCLK/
GP1[17]
AC3
I/O
IPU
DVDD
SPI[1]
PINCNTL86
DSIS: PIN
MM: MUX1
I/O
IPU
DVDD_GP
MC
GPMC, SPI[2],
HDMI, TIMER4
PINCNTL111
DSIS: PIN
MM: MUX0
I/O
IPU
DVDD
SPI[1]
PINCNTL85
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD_GP
MC
GPMC, SPI[2]
PINCNTL110
DSIS: PIN
MM: MUX0
I/O
IPU
DVDD_GP
MC
SD2
PINCNTL121
DSIS: PIN
MM: MUX1
AD28
I/O
IPU
DVDD_GP
MC
GPMC, SPI[2]
PINCNTL109
DSIS: PIN
MM: MUX0
L26
I/O
IPU
DVDD_GP
MC
SD2, GPMC
PINCNTL120
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD_GP
MC
GPMC, TIMER3
PINCNTL108
DSIS: PIN
MM: MUX0
GPMC_A[22]/
SPI[2]_D[1]/
HDMI_CEC/
TIM4_IO/
GP1[17]
SPI[1]_SCS[0]/
GP1[16]
GPMC_A[21]/
SPI[2]_D[0]/
GP1[16]
SD2_CLK/
GP1[15]
GPMC_A[20]/
SPI[2]_SCS[1]/
GP1[15]
SD2_DAT[0]/
GPMC_A[4]/
GP1[14]
GPMC_A[19]/
TIM3_IO/
GP1[14]
AB27
AD3
AC28
M23
AC27
DESCRIPTION
General-Purpose Input/Output (I/O) 1 [GP1] pin 18
General-Purpose Input/Output (I/O) 1 [GP1] pin 17
General-Purpose Input/Output (I/O) 1 [GP1] pin 16
General-Purpose Input/Output (I/O) 1 [GP1] pin 15
General-Purpose Input/Output (I/O) 1 [GP1] pin 14
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
77
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-11. GP1 Terminal Functions (continued)
SIGNAL
NAME
NO.
SD2_DAT[1]_SDIRQ
/
GPMC_A[3]/
GP1[13]
M24
TYPE (1)
OTHER (2)
(3)
MUXED
I/O
IPU
DVDD_GP
MC
SD2, GPMC
PINCNTL119
DSIS: PIN
MM: MUX1
GPMC, TIMER2
PINCNTL107
DSIS: PIN
MM: MUX0
GPMC_A[18]/
TIM2_IO/
GP1[13]
AE28
I/O
IPD
DVDD_GP
MC
VIN[0]A_D[1]/
GP1[12]
AB11
I/O
IPD
DVDD
VIN[0]A
PINCNTL141
DSIS: PIN
MM: MUX1
MDIO
PINCNTL234
DSIS: PIN
MM: MUX0
MDIO/
GP1[12]
P24
I/O
IPU
DVDD_GP
MC
VIN[0]A_D[0]/
GP1[11]
AF9
I/O
IPD
DVDD
VIN[0]A
PINCNTL140
DSIS: PIN
MM: MUX1
I/O
IPU
DVDD_GP
MC
MDIO
PINCNTL233
DSIS: PIN
MM: MUX0
MDCLK/
GP1[11]
H28
DESCRIPTION
General-Purpose Input/Output (I/O) 1 [GP1] pin 13
General-Purpose Input/Output (I/O) 1 [GP1] pin 12
General-Purpose Input/Output (I/O) 1 [GP1] pin 11
General-Purpose Input/Output (I/O) 1 [GP1] pin 10
GP1[10]
V2
I/O
IPU
DVDD_M
PINCNTL65
DSIS: PIN
MM: MUX1
EMAC_RMREFCLK/
TIM2_IO/
GP1[10]
J27
I/O
IPD
DVDD_GP
MC
EMAC, TIMER2
PINCNTL232
DSIS: PIN
MM: MUX0
The ENLVCMOS bit in the MLBP_DAT_IO_CTRL register
should be set to 1 to enable GPIO LVCMOS mode. The
ENN bit in the MLBP_DAT_IO_CTRL register should also
be set to 1 to enable the GPIO LVCMOS receiver. The
internal Pullup/Pulldown is always disabled, regardless of
the state of the PULLUDEN bit in the PINCNTL65 register.
An external Pullup/Pulldown can be used to control the
floating state of this pin.
General-Purpose Input/Output (I/O) 1 [GP1] pin 10
General-Purpose Input/Output (I/O) 1 [GP1] pin 9
GP1[9]
VIN[0]B_CLK/
CLKOUT0/
GP1[9]
V1
I/O
IPD
DVDD_M
AE17
I/O
IPD
DVDD
PINCNTL64
DSIS: PIN
MM: MUX1
The ENLVCMOS bit in the MLBP_DAT_IO_CTRL register
should be set to 1 to enable GPIO LVCMOS mode. The
ENP bit in the MLBP_DAT_IO_CTRL register should also
be set to 1 to enable the GPIO LVCMOS receiver. The
internal Pullup/Pulldown is always disabled, regardless of
the state of the PULLUDEN bit in the PINCNTL64 register.
An external Pullup/Pulldown can be used to control the
floating state of this pin.
VIN[0]B, CLKOUT0
PINCNTL134
General-Purpose Input/Output (I/O) 1 [GP1] pin 9
DSIS: PIN
MM: MUX0
General-Purpose Input/Output (I/O) 1 [GP1] pin 8
GP1[8]
78
W2
Device Pins
I/O
IPU
DVDD_M
PINCNTL63
DSIS: PIN
MM: MUX1
The ENLVCMOS bit in the MLBP_DAT_IO_CTRL register
should be set to 1 to enable GPIO LVCMOS mode. The
ENN bit in the MLBP_DAT_IO_CTRL register should also
be set to 1 to enable the GPIO LVCMOS receiver. The
internal Pullup/Pulldown is always disabled, regardless of
the state of the PULLUDEN bit in the PINCNTL63 register.
An external Pullup/Pulldown can be used to control the
floating state of this pin.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-11. GP1 Terminal Functions (continued)
SIGNAL
NAME
NO.
GPMC_CS[4]/
SD2_CMD/
GP1[8]
P25
TYPE (1)
I/O
OTHER (2)
(3)
MUXED
IPU
DVDD_GP
MC
GPMC, SD2
PINCNTL126
DSIS: PIN
MM: MUX0
DESCRIPTION
General-Purpose Input/Output (I/O) 1 [GP1] pin 8
General-Purpose Input/Output (I/O) 1 [GP1] pin 7
GP1[7]
DEVOSC_WAKE/
SPI[1]_SCS[1]/
TIM5_IO/
GP1[7]
SPI[0]_SCS[1]/
SD1_SDCD/
SATA_ACT0_LED/
EDMA_EVT1/
TIM4_IO/
GP1[6]
W1
W6
AE5
The ENLVCMOS bit in the MLBP_DAT_IO_CTRL register
should be set to 1 to enable GPIO LVCMOS mode. The
ENP bit in the MLBP_DAT_IO_CTRL register should also
be set to 1 to enable the GPIO LVCMOS receiver. The
internal Pullup/Pulldown is always disabled, regardless of
the state of the PULLUDEN bit in the PINCNTL62 register.
An external Pullup/Pulldown can be used to control the
floating state of this pin.
I/O
IPD
DVDD_M
PINCNTL62
DSIS: PIN
MM: MUX1
I/O
IPU
DVDD_SD
DEVOSC, SPI[1],
TIMER5
PINCNTL7
DSIS: PIN
MM: MUX0
I/O
IPU
DVDD
UART0, UART3,
UART1
PINCNTL77
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 5
UART0, UART3,
UART1
PINCNTL76
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 4
General-Purpose Input/Output (I/O) 1 [GP1] pin 7
SPI[0], SD1, SATA,
EDMA, TIMER4
General-Purpose Input/Output (I/O) 1 [GP1] pin 6
PINCNTL80
DSIS: PIN
UART0_RIN/
UART3_RTS/
UART1_RXD/
GP1[5]
AF4
I/O
IPU
DVDD
UART0_DTR/
UART3_CTS/
UART1_TXD/
GP1[4]
AG2
I/O
IPU
DVDD
UART0_DSR/
UART3_TXD/
SPI[0]_SCS[2]/
I2C[2]_SDA/
SD1_SDWP/
GP1[3]
AG4
I/O
IPU
DVDD
UART0, UART3,
SPI[0], I2C[2], SD1
General-Purpose Input/Output (I/O) 1 [GP1] pin 3
PINCNTL75
DSIS: PIN
UART0, UART3,
SPI[0], I2C[2], SD1
General-Purpose Input/Output (I/O) 1 [GP1] pin 2
PINCNTL74
DSIS: PIN
UART0_DCD/
UART3_RXD/
SPI[0]_SCS[3]/
I2C[2]_SCL/
SD1_POW/
GP1[2]
AH4
I/O
IPU
DVDD
DCAN0_RX/
UART2_RXD/
I2C[3]_SCL/
GP1[1]
AG6
I/O
IPU
DVDD
DCAN0, UART2,
I2C[3]
PINCNTL69
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 1
DCAN0_TX/
UART2_TXD/
I2C[3]_SDA/
GP1[0]
AH6
I/O
IPU
DVDD
DCAN0, UART2,
I2C[3]
PINCNTL68
DSIS: PIN
General-Purpose Input/Output (I/O) 1 [GP1] pin 0
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
79
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-12. GP2 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
GPIO2
Note: General-Purpose Input/Output (I/O) pins can also serve as external interrupt inputs.
VOUT[1]_AVID/
EMAC[1]_MRXER/
VIN[1]A_CLK/
UART4_RTS/
TIM6_IO/
GP2[31]
VOUT[1]_VSYNC/
EMAC[1]_MCRS/
VIN[1]A_FLD/
VIN[1]A_DE/
SPI[3]_D[0]/
UART3_CTS/
GP2[30]
Y22
AA23
I/O
IPD
DVDD
VOUT[1], EMAC[1],
VIN[1]A, UART4,
TIMER6
General-Purpose Input/Output (I/O) 2 [GP2] pin 31
PINCNTL207
DSIS: PIN
I/O
IPD
DVDD
VOUT[1], EMAC[1],
VIN[1]A, SPI[3],
UART3
General-Purpose Input/Output (I/O) 2 [GP2] pin 30
PINCNTL206
DSIS: PIN
VOUT[1]_HSYNC/
EMAC[1]_MCOL/
VIN[1]A_VSYNC/
SPI[3]_D[1]/
UART3_RTS/
GP2[29]
AC24
I/O
IPD
DVDD
VOUT[1], EMAC[1],
VIN[1]A, SPI[3],
UART3
General-Purpose Input/Output (I/O) 2 [GP2] pin 29
PINCNTL205
DSIS: PIN
VOUT[1]_CLK/
EMAC[1]_MTCLK/
VIN[1]A_HSYNC/
GP2[28]
AE24
I/O
IPD
DVDD
VOUT[1], EMAC[1],
VIN[1]A
General-Purpose Input/Output (I/O) 2 [GP2] pin 28
PINCNTL204
DSIS: PIN
VOUT[0]_R_CR[3]/
GP2[27]
AB9
I/O
IPD
DVDD
VOUT[0]
PINCNTL197
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 27
VOUT[0]_R_CR[2]/
EMU4/
GP2[26]
AD9
I/O
IPD
DVDD
VOUT[0], EMU
PINCNTL196
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 26
VOUT[0]_G_Y_YC[3]/
GP2[25]
AH15
I/O
IPD
DVDD
VOUT[0]
PINCNTL189
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 25
VOUT[0]_G_Y_YC[2]/
EMU3/
GP2[24]
AH7
I/O
IPD
DVDD
VOUT[0], EMU
PINCNTL188
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 24
VOUT[0]_B_CB_C[3]/
GP2[23]
AE15
I/O
IPD
DVDD
VOUT[0]
PINCNTL181
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 23
VOUT[0]_B_CB_C[2]/
EMU2/
GP2[22]
AG7
I/O
IPD
DVDD
VOUT[0], EMU
PINCNTL180
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 22
VOUT[0]_AVID/
VOUT[0]_FLD/
SPI[3]_SCLK/
TIM7_IO/
GP2[21]
AA10
I/O
IPD
DVDD
VOUT[0], SPI[3],
TIMER7
PINCNTL179
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 21
VIN[0]A_D[15]_BD[7]/
CAM_SHUTTER/
GP2[20]
AC14
I/O
DIS
DVDD
VIN[0]AB,
CAMERA_I/F
PINCNTL155
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 20
(1)
(2)
(3)
80
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-12. GP2 Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
VIN[0]A_D[14]_BD[6]/
CAM_STROBE/
GP2[19]
AC12
I/O
IPD
DVDD
VIN[0]AB,
CAMERA_I/F
PINCNTL154
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 19
VIN[0]A_D[13]_BD[5]/
CAM_RESET/
GP2[18]
AF17
I/O
IPD
DVDD
VIN[0]AB,
CAMERA_I/F
PINCNTL153
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 18
VIN[0]A_D[12]_BD[4]/
CLKOUT1/
GP2[17]
AG17
I/O
IPD
DVDD
VIN[0]AB,
CLKOUT1
PINCNTL152
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 17
VIN[0]A_D[11]_BD[3]/
CAM_WE/
GP2[16]
AH17
I/O
IPD
DVDD
VIN[0]AB,
CAMERA_I/F
PINCNTL151
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 16
VIN[0]A_D[10]_BD[2]/
GP2[15]
AH9
I/O
IPD
DVDD
VIN[0]AB
PINCNTL150
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 15
VIN[0]A_D[9]_BD[1]/
GP2[14]
AG9
I/O
IPD
DVDD
VIN[0]AB
PINCNTL149
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 14
VIN[0]A_D[8]_BD[0]/
GP2[13]
AB15
I/O
IPD
DVDD
VIN[0]AB
PINCNTL148
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 13
VIN[0]A_D[7]/
GP2[12]
AA11
I/O
IPD
DVDD
VIN[0]A
PINCNTL147
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 12
VIN[0]A_D[6]/
GP2[11]
AH16
I/O
IPD
DVDD
VIN[0]A
PINCNTL146
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 11
VIN[0]A_D[5]/
GP2[10]
AG16
I/O
IPD
DVDD
VIN[0]A
PINCNTL145
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 10
VIN[0]A_D[4]/
GP2[9]
AH8
I/O
IPD
DVDD
VIN[0]A
PINCNTL144
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 9
VIN[0]A_D[3]/
GP2[8]
AE12
I/O
IPD
DVDD
VIN[0]A
PINCNTL143
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 8
VIN[0]A_D[2]/
GP2[7]
AC9
I/O
IPD
DVDD
VIN[0]A
PINCNTL142
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 7
I/O
IPU
DVDD_GP
MC
SD2, GPMC
PINCNTL118
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD_GP
MC
GPMC
PINCNTL106
DSIS: PIN
MM: MUX0
I/O
IPU
DVDD_GP
MC
SD2, GPMC
PINCNTL117
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD_GP
MC
GPMC
PINCNTL105
DSIS: PIN
MM: MUX0
SD2_DAT[2]_SDRW/
GPMC_A[2]/
GP2[6]
GPMC_A[17]/
GP2[6]
SD2_DAT[3]/
GPMC_A[1]/
GP2[5]
GPMC_A[16]/
GP2[5]
K27
V23
J28
AD27
General-Purpose Input/Output (I/O) 2 [GP2] pin 6
General-Purpose Input/Output (I/O) 2 [GP2] pin 5
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
81
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-12. GP2 Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
VIN[0]A_VSYNC/
UART5_CTS/
GP2[4]
AD20
I/O
IPU
DVDD
VIN[0]A, UART5
PINCNTL139
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 4
VIN[0]A_HSYNC/
UART5_RTS/
GP2[3]
AC20
I/O
IPU
DVDD
VIN[0]A, UART5
PINCNTL138
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 3
I/O
IPD
DVDD
VIN[0]A
PINCNTL137
DSIS: PIN
MM: MUX1
VIN[0]A_CLK/
GP2[2]
AB20
VOUT[0]_FLD/
CAM_PCLK/
GPMC_A[12]/
UART2_RTS/
GP2[2]
AF18
I/O
IPD
DVDD_C
VOUT[0],
CAMERA_I/F,
GPMC, UART2
PINCNTL175
DSIS: PIN
MM: MUX0
VIN[0]A_FLD/
VIN[0]B_VSYNC/
UART5_RXD/
I2C[2]_SCL/
GP2[1]
AA20
I/O
IPU
DVDD
VIN[0]A, VIN[0]B,
UART5, I2C[2]
PINCNTL136
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 1
I/O
IPU
DVDD
VIN[0]A, VIN[0]B,
UART5, I2C[2]
PINCNTL135
DSIS: PIN
General-Purpose Input/Output (I/O) 2 [GP2] pin 0
VIN[0]A_DE/
VIN[0]B_HSYNC/
UART5_TXD/
I2C[2]_SDA/
GP2[0]
82
Device Pins
AE21
General-Purpose Input/Output (I/O) 2 [GP2] pin 2
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-13. GP3 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
GPIO3
Note: General-Purpose Input/Output (I/O) pins can also serve as external interrupt inputs.
CLKIN32/
CLKOUT0/
TIM3_IO/
GP3[31]
J7
I/O
IPD
DVDD
CLKIN32,
CLKOUT0,
TIMER3
PINCNTL259
DSIS: PIN
IPU
DVDD
VOUT[1], GPMC,
VIN[1]A, HDMI,
SPI[2]
PINCNTL231
DSIS: PIN
MM: MUX1
General-Purpose Input/Output (I/O) 3 [GP3] pin 31.
VOUT[1]_B_CB_C[2]/
GPMC_A[0]/
VIN[1]A_D[7]/
HDMI_CEC/
SPI[2]_D[0]/
GP3[30]
AF28
EMAC[0]_MRXD[2]/
EMAC[0]_RGRXD[1]/
VIN[1]B_D[7]/
EMAC[0]_RMTXEN/
GP3[30]
R23
I/O
IPD
DVDD_GPMC
EMAC[0], VIN[1]B
PINCNTL242
DSIS: PIN
MM: MUX0
EMAC[0]_MRXD[1]/
EMAC[0]_RGRXD[0]/
VIN[1]B_D[6]/
EMAC[0]_RMTXD[1]/
GP3[29]
P23
I/O
IPD
DVDD_GPMC
EMAC[0], VIN[1]B
PINCNTL241
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 29.
EMAC[0]_MRXD[0]/
EMAC[0]_RGTXD[0]/
VIN[1]B_D[5]/
EMAC[0]_RMTXD[0]/
GP3[28]
G28
I/O
IPD
DVDD_GPMC
EMAC[0], VIN[1]B
PINCNTL240
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 28.
EMAC[0]_MRCLK/
EMAC[0]_RGTXC/
VIN[1]B_D[4]/
EMAC[0]_RMCRSDV/
SPI[3]_SCS[2]/
GP3[27]
H27
I/O
IPD
DVDD_GPMC
EMAC[0], VIN[1]B,
SPI[3]
General-Purpose Input/Output (I/O) 3 [GP3] pin 27.
PINCNTL239
DSIS: PIN
EMAC[0]_MRXER/
EMAC[0]_RGTXCTL/
VIN[1]B_D[3]/
EMAC[0]_RMRXER/
GP3[26]
J26
I/O
IPD
DVDD_GPMC
EMAC[0], VIN[1]B
PINCNTL238
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 26.
EMAC[0]_MCRS/
EMAC[0]_RGRXD[2]/
VIN[1]B_D[2]/
EMAC[0]_RMRXD[1]/
GP3[25]
R25
I/O
IPD
DVDD_GPMC
EMAC[0], VIN[1]B
PINCNTL237
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 25.
EMAC[0]_MCOL/
EMAC[0]_RGRXCTL/
VIN[1]B_D[1]/
EMAC[0]_RMRXD[0]/
GP3[24]
L23
I/O
IPD
DVDD_GPMC
EMAC[0], VIN[1]B
PINCNTL236
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 24.
I/O
IPD
DVDD_GPMC
EMAC[0], VIN[1]B,
SPI[3], I2C[2]
General-Purpose Input/Output (I/O) 3 [GP3] pin 23.
PINCNTL235
DSIS: PIN
EMAC[0]_MTCLK/
EMAC[0]_RGRXC/
VIN[1]B_D[0]/
SPI[3]_SCS[3]/
I2C[2]_SDA/
GP3[23]
(1)
(2)
(3)
L24
I/O
General-Purpose Input/Output (I/O) 3 [GP3] pin 30.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
83
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-13. GP3 Terminal Functions (continued)
SIGNAL
NAME
VOUT[1]_R_CR[2]/
GPMC_A[15]/
VIN[1]A_D[23]/
HDMI_HPDET/
SPI[2]_D[1]/
GP3[22]
VOUT[1]_R_CR[3]/
GPMC_A[14]/
VIN[1]A_D[22]/
HDMI_SDA/
SPI[2]_SCLK/
I2C[2]_SDA
GP3[21]
VOUT[1]_G_Y_YC[2]/
GPMC_A[13]/
VIN[1]A_D[21]/
HDMI_SCL/
SPI[2]_SCS[2]/
I2C[2]_SCL/
GP3[20]
VOUT[1]_R_CR[9]/
EMAC[1]_MTXEN/
VIN[1]A_D[20]/
UART5_TXD/
GP3[19]
VOUT[1]_R_CR[8]/
EMAC[1]_MTXD[7]/
VIN[1]A_D[19]/
UART5_RXD/
GP3[18]
VOUT[1]_R_CR[7]/
EMAC[1]_MTXD[6]/
VIN[1]A_D[18]/
SPI[3]_D[0]/
GP3[17]
VOUT[1]_R_CR[6]/
EMAC[1]_MTXD[5]/
VIN[1]A_D[17]/
SPI[3]_D[1]/
GP3[16]
VOUT[1]_R_CR[5]/
EMAC[1]_MTXD[4]/
VIN[1]A_D[16]/
SPI[3]_SCLK/
GP3[15]
NO.
AE27
AG28
AF27
Y24
W23
V22
AA25
AC26
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
I/O
IPD
DVDD
VOUT[1], GPMC,
VIN[1]A, HDMI,
SPI[2]
PINCNTL230
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 22.
I/O
IPU
DVDD
VOUT[1], GPMC,
VIN[1]A, HDMI,
SPI[2], I2C[2]
PINCNTL229
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 21.
I/O
IPU
DVDD
VOUT[1], GPMC,
VIN[1]A, HDMI,
SPI[2], I2C[2]
PINCNTL228
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 20.
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
UART5
General-Purpose Input/Output (I/O) 3 [GP3] pin 19.
PINCNTL227
DSIS: PIN
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
UART5
General-Purpose Input/Output (I/O) 3 [GP3] pin 18.
PINCNTL226
DSIS: PIN
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
SPI[3]
General-Purpose Input/Output (I/O) 3 [GP3] pin 17.
PINCNTL225
DSIS: PIN
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
SPI[3]
General-Purpose Input/Output (I/O) 3 [GP3] pin 16.
PINCNTL224
DSIS: PIN
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
SPI[3]
General-Purpose Input/Output (I/O) 3 [GP3] pin 15.
PINCNTL223
DSIS: PIN
VOUT[1]_R_CR[4]/
EMAC[1]_MTXD[3]/
VIN[1]A_D[15]/
SPI[3]_SCS[1]/
GP3[14]
AG27
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
SPI[3]
General-Purpose Input/Output (I/O) 3 [GP3] pin 14.
PINCNTL222
DSIS: PIN
VOUT[1]_G_Y_YC[9]/
EMAC[1]_MTXD[2]/
VIN[1]A_D[14]/
GP3[13]
AD26
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A
PINCNTL221
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 13.
VOUT[1]_G_Y_YC[8]/
EMAC[1]_MTXD[1]/
VIN[1]A_D[13]/
GP3[12]
AE26
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A
PINCNTL220
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 12.
VOUT[1]_G_Y_YC[7]/
EMAC[1]_MTXD[0]/
VIN[1]A_D[12]/
GP3[11]
AF26
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A
PINCNTL219
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 11.
84
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-13. GP3 Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
VOUT[1]_G_Y_YC[6]/
EMAC[1]_GMTCLK/
VIN[1]A_D[11]/
GP3[10]
AH27
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A
PINCNTL218
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 10.
VOUT[1]_G_Y_YC[5]/
EMAC[1]_MRXDV/
VIN[1]A_D[10]/
GP3[9]
AG26
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A
PINCNTL217
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 9.
VOUT[1]_G_Y_YC[4]/
EMAC[1]_MRXD[7]/
VIN[1]A_D[9]/
GP3[8]
W22
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A
PINCNTL216
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 8.
VOUT[1]_G_Y_YC[3]/
EMAC[1]_MRXD[6]/
VIN[1]A_D[8]/
GP3[7]
Y23
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A
PINCNTL215
DSIS: PIN
General-Purpose Input/Output (I/O) 3 [GP3] pin 7.
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
I2C[3]
General-Purpose Input/Output (I/O) 3 [GP3] pin 6.
PINCNTL214
DSIS: PIN
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
I2C[3]
General-Purpose Input/Output (I/O) 3 [GP3] pin 5.
PINCNTL213
DSIS: PIN
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
UART3
General-Purpose Input/Output (I/O) 3 [GP3] pin 4.
PINCNTL212
DSIS: PIN
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
UART3
General-Purpose Input/Output (I/O) 3 [GP3] pin 3.
PINCNTL211
DSIS: PIN
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
UART4
General-Purpose Input/Output (I/O) 3 [GP3] pin 2.
PINCNTL210
DSIS: PIN
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
UART4
General-Purpose Input/Output (I/O) 3 [GP3] pin 1.
PINCNTL209
DSIS: PIN
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
UART4
General-Purpose Input/Output (I/O) 2 [GP2] pin 0.
PINCNTL208
DSIS: PIN
VOUT[1]_B_CB_C[9]/
EMAC[1]_MRXD[5]/
VIN[1]A_D[6]/
I2C[3]_SDA/
GP3[6]
VOUT[1]_B_CB_C[8]/
EMAC[1]_MRXD[4]/
VIN[1]A_D[5]/
I2C[3]_SCL/
GP3[5]
VOUT[1]_B_CB_C[7]/
EMAC[1]_MRXD[3]/
VIN[1]A_D[4]/
UART3_TXD/
GP3[4]
VOUT[1]_B_CB_C[6]/
EMAC[1]_MRXD[2]/
VIN[1]A_D[3]/
UART3_RXD/
GP3[3]
VOUT[1]_B_CB_C[5]/
EMAC[1]_MRXD[1]/
VIN[1]A_D[2]/
UART4_TXD/
GP3[2]
VOUT[1]_B_CB_C[4]/
EMAC[1]_MRXD[0]/
VIN[1]A_D[1]/
UART4_RXD/
GP3[1]
VOUT[1]_B_CB_C[3]/
EMAC[1]_MRCLK/
VIN[1]A_D[0]/
UART4_CTS/
GP3[0]
AA24
AH26
AC25
AD25
AF25
AG25
AH25
I/O
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
85
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.8
www.ti.com
GPMC
Table 3-14. GPMC Terminal Functions
SIGNAL
NAME
GPMC_CLK/
GPMC_CS[5]/
GPMC_WAIT[1]/
CLKOUT1/
EDMA_EVT3/
TIM4_IO/
GP1[27]
SD2_DAT[4]/
GPMC_A[27]/
GPMC_A[23]/
GPMC_CS[7]/
EDMA_EVT0/
TIM7_IO/
GP1[22]
GPMC_ADV_ALE/
GPMC_CS[6]/
TIM5_IO/
GP1[28]
NO.
R26
R24
M26
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
GPMC, CLKOUT1,
EDMA, TIMER4,
GP1
GPMC Clock output
PINCNTL127
DSIS: 0
O
IPU
DVDD_GPMCB
O
IPU
DVDD_GPMC
SD2, GPMC,
EDMA, TIMER7,
GP1
PINCNTL116
DSIS: N/A
GPMC Chip Select 7
O
IPU
DVDD_GPMCB
GPMC, TIMER5,
GP1
PINCNTL128
DSIS: N/A
GPMC Chip Select 6
GPMC_CLK/
GPMC_CS[5]/
GPMC_WAIT[1]/
CLKOUT1/
EDMA_EVT3/
TIM4_IO/
GP1[27]
R26
O
IPU
DVDD_GPMCB
GPMC_CS[4]/
SD2_CMD/
GP1[8]
P25
O
IPU
DVDD_GPMC
SD2, GP1
PINCNTL126
DSIS: N/A
GPMC Chip Select 4
GPMC_CS[3]/
VIN[1]B_CLK/
SPI[2]_SCS[0]/
GP1[26]
P26
O
IPU
DVDD_GPMC
VIN[1]B, SPI[2],
GP1
PINCNTL125
DSIS: N/A
GPMC Chip Select 3
GPMC_CS[2]/
GPMC_A[24]/
GP1[25]
M25
O
IPU
DVDD_GPMC
GPMC, GP1
PINCNTL124
DSIS: N/A
GPMC Chip Select 2
GPMC_CS[1]/
GPMC_A[25]/
GP1[24]
K28
O
IPU
DVDD_GPMCB
GPMC, GP1
PINCNTL123
DSIS: N/A
GPMC Chip Select 1
GPMC_CS[0]/
GP1[23]
T28
O
IPU
DVDD_GPMCB
GP1
PINCNTL122
DSIS: N/A
GPMC Chip Select 0
GPMC_WE
U28
O
IPU
DVDD_GPMCB
–
PINCNTL130
DSIS: N/A
GPMC Write Enable output
GPMC_OE_RE
T27
O
IPU
DVDD_GPMCB
–
PINCNTL129
DSIS: N/A
GPMC Output Enable output
O
IPD
DVDD_GPMCB
GPMC, EDMA,
TIMER7, GP1
PINCNTL132
DSIS: N/A
GPMC_BE[1]/
GPMC_A[24]/
EDMA_EVT1/
TIM7_IO/
GP1[30]
(1)
(2)
(3)
86
V28
GPMC, CLKOUT1,
EDMA, TIMER4,
GP1
GPMC Chip Select 5
PINCNTL127
DSIS: N/A
GPMC Upper Byte Enable output
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and the Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-14. GPMC Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
GPMC_BE[0]_CLE/
GPMC_A[25]/
EDMA_EVT2/
TIM6_IO/
GP1[29]
U27
O
IPD
DVDD_GPMCB
GPMC, EDMA,
TIMER6, GP1
PINCNTL131
DSIS: PIN
GPMC Lower Byte Enable output or Command
Latch Enable output
GPMC_ADV_ALE/
GPMC_CS[6]/
TIM5_IO/
GP1[28]
M26
O
IPU
DVDD_GPMCB
GPMC, TIMER5,
GP1
PINCNTL128
DSIS: N/A
GPMC Address Valid output or Address Latch
Enable output
GPMC_CLK/
GPMC_CS[5]/
GPMC_WAIT[1]/
CLKOUT1/
EDMA_EVT3/
TIM4_IO/
GP1[27]
R26
I
IPU
DVDD_GPMCB
GPMC_WAIT[0]/
GPMC_A[26]/
EDMA_EVT0/
GP1[31]
W28
I
IPU
DVDD_GPMCB
GPMC, EDMA,
GP1
PINCNTL133
DSIS: 1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], GPMC,
UART5
PINCNTL243
DSIS: N/A
MM: MUX1
IPU
DVDD_GPMC
SD2, GPMC,
EDMA, TIMER7,
GP1
PINCNTL116
DSIS: N/A
MM: MUX0
IPU
DVDD_GPMCB
GPMC, EDMA,
GP1
PINCNTL133
DSIS: N/A
MM: MUX2
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], GPMC,
UART5
PINCNTL243
DSIS: N/A
MM: MUX1
IPU
DVDD_GPMC
SD2, GPMC,
TIMER6, GP1
PINCNTL115
DSIS: N/A
MM: MUX0
EMAC[0]_MRXD[3]/
EMAC[1]_RGRXCTL/
GPMC_A[27]/
GPMC_A[26]/
GPMC_A[0]/
UART5_RXD
SD2_DAT[4]/
GPMC_A[27]/
GPMC_A[23]/
GPMC_CS[7]/
EDMA_EVT0/
TIM7_IO/
GP1[22]
GPMC_WAIT[0]/
GPMC_A[26]/
EDMA_EVT0/
GP1[31]
EMAC[0]_MRXD[3]/
EMAC[1]_RGRXCTL/
GPMC_A[27]/
GPMC_A[26]/
GPMC_A[0]/
UART5_RXD
SD2_DAT[5]/
GPMC_A[26]/
GPMC_A[22]/
TIM6_IO/
GP1[21]
J25
R24
W28
J25
P22
O
O
O
O
O
GPMC, CLKOUT1,
EDMA, TIMER4,
GP1
GPMC Wait input 1
PINCNTL127
DSIS: 1
GPMC Wait input 0
GPMC Address 27
GPMC Address 26
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
87
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-14. GPMC Terminal Functions (continued)
SIGNAL
NAME
NO.
GPMC_BE[0]_CLE/
GPMC_A[25]/
EDMA_EVT2/
TIM6_IO/
GP1[29]
U27
GPMC_CS[1]/
GPMC_A[25]/
GP1[24]
K28
SD2_DAT[6]/
GPMC_A[25]/
GPMC_A[21]/
UART2_TXD/
GP1[20]
N23
TYPE (1)
OTHER (2)
(3)
MUXED
O
IPD
DVDD_GPMCB
GPMC, EDMA,
TIMER6, GP1
PINCNTL131
DSIS: N/A
MM: MUX2
O
IPU
DVDD_GPMCB
GPMC, GP1
PINCNTL123
DSIS: N/A
MM: MUX1
O
IPU
DVDD_GPMC
SD2, GPMC,
UART2, GP1
PINCNTL114
DSIS: N/A
MM: MUX0
GPMC_BE[1]/
GPMC_A[24]/
EDMA_EVT1/
TIM7_IO/
GP1[30]
V28
O
IPD
DVDD_GPMCB
GPMC, EDMA,
TIMER7, GP1
PINCNTL132
DSIS: N/A
MM: MUX2
GPMC_CS[2]/
GPMC_A[24]/
GP1[25]
M25
O
IPU
DVDD_GPMC
GPMC, GP1
PINCNTL124
DSIS: N/A
MM: MUX1
O
IPU
DVDD_GPMC
SD2, GPMC,
UART2, GP1
PINCNTL113
DSIS: N/A
MM: MUX0
IPU
DVDD_GPMC
SD2, GPMC,
EDMA, TIMER5,
GP1
PINCNTL116
DSIS: N/A
MM: MUX1
SD2_DAT[7]/
GPMC_A[24]/
GPMC_A[20]/
UART2_RXD/
GP1[19]
SD2_DAT[4]/
GPMC_A[27]/
GPMC_A[23]/
GPMC_CS[7]/
EDMA_EVT0/
TIM7_IO/
GP1[22]
GPMC_A[23]/
SPI[2]_SCLK/
HDMI_HPDET/
TIM5_IO/
GP1[18]
SD2_DAT[5]/
GPMC_A[26]/
GPMC_A[22]/
TIM6_IO/
GP1[21]
GPMC_A[22]/
SPI[2]_D[1]/
HDMI_CEC/
TIM4_IO/
GP1[17]
SD2_DAT[6]/
GPMC_A[25]/
GPMC_A[21]/
UART2_TXD/
GP1[20]
GPMC_A[21]/
SPI[2]_D[0]/
GP1[16]
88
Device Pins
L25
R24
AA26
P22
AB27
N23
AC28
O
IPD
DVDD_GPMCB
SPI[2], HDMI,
TIMER5, GP1
PINCNTL112
DSIS: N/A
MM: MUX0
IPU
DVDD_GPMC
SD2, GPMC,
TIMER6, GP1
PINCNTL115
DSIS: N/A
MM: MUX1
O
IPU
DVDD_GPMCB
SPI[2], HDMI,
TIMER4, GP1
PINCNTL111
DSIS: N/A
MM: MUX0
O
IPU
DVDD_GPMC
SD2, GPMC,
UART2, GP1
PINCNTL114
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMCB
SPI[2], GP1
PINCNTL110
DSIS: N/A
MM: MUX0
O
O
O
DESCRIPTION
GPMC Address 25
GPMC Address 24
GPMC Address 23
GPMC Address 22
GPMC Address 21
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-14. GPMC Terminal Functions (continued)
SIGNAL
NAME
SD2_DAT[7]/
GPMC_A[24]/
GPMC_A[20]/
UART2_RXD/
GP1[19]
NO.
L25
TYPE (1)
O
OTHER (2)
(3)
MUXED
IPU
DVDD_GPMC
SD2, GPMC,
UART2, GP1
PINCNTL113
DSIS: N/A
MM: MUX1
DESCRIPTION
GPMC Address 20
GPMC_A[20]/
SPI[2]_SCS[1]/
GP1[15]
AD28
O
IPU
DVDD_GPMCB
SPI[2], GP1
PINCNTL109
DSIS: N/A
MM: MUX0
GPMC_A[19]/
TIM3_IO/
GP1[14]
AC27
O
IPD
DVDD_GPMCB
TIMER2, GP1
PINCNTL108
DSIS: N/A
GPMC Address 19
GPMC_A[18]/
TIM2_IO/
GP1[13]
AE28
O
IPD
DVDD_GPMCB
TIMER2, GP1
PINCNTL107
DSIS: N/A
GPMC Address 18
GPMC_A[17]/
GP2[6]
V23
O
IPD
DVDD_GPMCB
GP2
PINCNTL106
DSIS: N/A
GPMC Address 17
GPMC_A[16]/
GP2[5]
AD27
O
IPD
DVDD_GPMCB
GP2
PINCNTL105
DSIS: N/A
GPMC Address 16
IPD
DVDD
VOUT[1], VIN[1]A,
HDMI, SPI[2],GP3
PINCNTL230
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], UART1
PINCNTL258
DSIS: N/A
MM: MUX0
IPU
DVDD
VOUT[1], VIN[1]A,
HDMI, SPI[2],
I2C[2], GP3
PINCNTL229
DSIS: N/A
MM: MUX1
VOUT[1]_R_CR[2]/
GPMC_A[15]/
VIN[1]A_D[23]/
HDMI_HPDET/
SPI[2]_D[1]/
GP3[22]
EMAC[0]_MTXEN/
EMAC[1]_RGRXD[2]/
EMAC[1]_RMTXEN/
GPMC_A[15]/
UART1_RTS
VOUT[1]_R_CR[3]/
GPMC_A[14]/
VIN[1]A_D[22]/
HDMI_SDA/
SPI[2]_SCLK/
I2C[2]_SDA/
GP3[21]
EMAC[0]_MTXD[7]/
EMAC[1]_RGTXD[3]/
EMAC[1]_RMTXD[1]/
GPMC_A[14]/
UART1_CTS
VOUT[1]_G_Y_YC[2]/
GPMC_A[13]/
VIN[1]A_D[21]/
HDMI_SCL/
SPI[2]_SCS[2]/
I2C[2]_SCL/
GP3[20]
EMAC[0]_MTXD[6]/
EMAC[1]_RGRXD[0]/
EMAC[1]_RMTXD[0]/
GPMC_A[13]/
UART1_TXD
AE27
J23
AG28
H24
AF27
J22
O
O
O
O
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], UART1
PINCNTL257
DSIS: N/A
MM: MUX0
IPU
DVDD
VOUT[1], VIN[1]A,
HDMI, SPI[2],
I2C[2], GP3
PINCNTL228
DSIS: N/A
MM: MUX1
O
O
IPD
DVDD_GPMC
GPMC Address 15
GPMC Address 14
GPMC Address 13
EMAC[0],
EMAC[1], UART1
PINCNTL256
DSIS: N/A
MM: MUX0
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
89
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-14. GPMC Terminal Functions (continued)
SIGNAL
NAME
VOUT[0]_FLD/
CAM_PCLK/
GPMC_A[12]/
UART2_RTS/
GP2[2]
EMAC[0]_MTXD[5]/
EMAC[1]_RGTXC/
EMAC[1]_RMCRSDV/
GPMC_A[12]/
UART1_RXD
VOUT[1]_FLD/
CAM_FLD/
CAM_WE/
GPMC_A[11]/
UART2_CTS/
GP0[28]
EMAC[0]_MTXD[4]/
EMAC[1]_RGTXD[2]/
EMAC[1]_RMRXER/
GPMC_A[11]/
UART4_RTS
VOUT[1]_B_CB_C[0]/
CAM_VS/
GPMC_A[10]/
UART2_TXD/
GP0[27]
EMAC[0]_MTXD[3]/
EMAC[1]_RGTXD[0]/
EMAC[1]_RMRXD[1]/
GPMC_A[10]/
UART4_CTS
VOUT[1]_B_CB_C[1]/
CAM_HS/
GPMC_A[9]/
UART2_RXD/
GP0[26]
EMAC[0]_MTXD[2]/
EMAC[1]_RGTXCTL/
EMAC[1]_RMRXD[0]/
GPMC_A[9]/
UART4_TXD
VOUT[1]_R_CR[0]/
CAM_D[0]/
GPMC_A[8]/
UART4_RTS/
GP0[25]
EMAC[0]_MTXD[1]/
EMAC[1]_RGTXD[1]/
GPMC_A[8]/
UART4_RXD
90
Device Pins
NO.
AF18
F27
AB23
G23
AD23
H23
AE23
H22
AA22
H25
TYPE (1)
O
O
O
O
O
O
O
O
O
O
OTHER (2)
(3)
MUXED
IPD
DVDD_C
VOUT[0],
CAMERA_I/F,
UART2, GP2
PINCNTL175
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], UART1
PINCNTL255
DSIS: N/A
MM: MUX0
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
UART2, GP0
PINCNTL174
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], UART4
PINCNTL254
DSIS: N/A
MM: MUX0
IPU
DVDD_C
VOUT[1],
CAMERA_I/F,
UART2, GP0
PINCNTL173
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], UART4
PINCNTL253
DSIS: N/A
MM: MUX0
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
UART2, GP0
PINCNTL172
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], UART4
PINCNTL252
DSIS: N/A
MM: MUX0
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
UART4, GP0
PINCNTL171
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], UART4
PINCNTL251
DSIS: N/A
MM: MUX0
DESCRIPTION
GPMC Address 12
GPMC Address 11
GPMC Address 10
GPMC Address 9
GPMC Address 8
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-14. GPMC Terminal Functions (continued)
SIGNAL
NAME
VOUT[1]_R_CR[1]/
CAM_D[1]/
GPMC_A[7]/
UART4_CTS/
GP0[24]
EMAC[0]_MTXD[0]/
EMAC[1]_RGRXD[3]/
GPMC_A[7]/
SPI[2]_D[0]
VOUT[1]_G_Y_YC[0]/
CAM_D[2]/
GPMC_A[6]/
UART4_TXD/
GP0[23]
EMAC[0]_GMTCLK/
EMAC[1]_RGRXC/
GPMC_A[6]/
SPI[2]_D[1]
VOUT[1]_G_Y_YC[1]/
CAM_D[3]/
GPMC_A[5]/
UART4_RXD/
GP0[22]
EMAC[0]_MRXDV/
EMAC[1]_RGRXD[1]/
GPMC_A[5]/
SPI[2]_SCLK
SD2_DAT[0]/
GPMC_A[4]/
GP1[14]
EMAC[0]_MRXD[7]/
EMAC[0]_RGTXD[1]/
GPMC_A[4]/
SPI[2]_SCS[3]
SD2_DAT[1]_ SDIRQ/
GPMC_A[3]/
GP1[13]
NO.
AC19
J24
AC18
K23
AD18
K22
L26
G27
M24
TYPE (1)
OTHER (2)
(3)
MUXED
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
UART4, GP0
PINCNTL170
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], SPI[2]
PINCNTL250
DSIS: N/A
MM: MUX0
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
UART4, GP0
PINCNTL169
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], SPI[2]
PINCNTL249
DSIS: N/A
MM: MUX0
IPU
DVDD_C
VOUT[1],
CAMERA_I/F,
UART4, GP0
PINCNTL168
DSIS: N/A
MM: MUX1
O
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], SPI[2]
PINCNTL248
DSIS: N/A
MM: MUX0
O
IPU
DVDD_GPMCB
SD2, GP1
PINCNTL120
DSIS: N/A
MM: MUX1
O
IPD
DVDD_GPMC
EMAC[0], SPI[2]
PINCNTL247
DSIS: N/A
MM: MUX0
O
IPU
DVDD_GPMC
SD2, GP1
PINCNTL119
DSIS: N/A
MM: MUX1
O
O
O
O
O
EMAC[0]_MRXD[6]/
EMAC[0]_RGTXD[2]/
GPMC_A[3]/
UART5_RTS
F28
O
IPD
DVDD_GPMC
EMAC[0], UART5
PINCNTL246
DSIS: N/A
MM: MUX0
SD2_DAT[2]_SDRW/
GPMC_A[2]/
GP2[6]
K27
O
IPU
DVDD_GPMC
SD2, GP2
PINCNTL118
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0], UART5
PINCNTL245
DSIS: N/A
MM: MUX0
EMAC[0]_MRXD[5]/
EMAC[0]_RGTXD[3]/
GPMC_A[2]/
UART5_CTS
H26
O
DESCRIPTION
GPMC Address 7
GPMC Address 6
GPMC Address 5
GPMC Address 4
GPMC Address 3
GPMC Address 2
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
91
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-14. GPMC Terminal Functions (continued)
SIGNAL
NAME
SD2_DAT[3]/
GPMC_A[1]/
GP2[5]
EMAC[0]_MRXD[4]/
EMAC[0]_RGRXD[3]/
GPMC_A[1]/
UART5_TXD
VOUT[1]_B_CB_C[2]/
GPMC_A[0]/
VIN[1]A_D[7]/
HDMI_CEC/
SPI[2]_D[0]/
GP3[30]
EMAC[0]_MRXD[3]/
EMAC[1]_RGRXCTL/
GPMC_A[27]/
GPMC_A[26]/
GPMC_A[0]/
UART5_RXD
92
Device Pins
NO.
J28
T23
AF28
J25
TYPE (1)
OTHER (2)
(3)
MUXED
IPU
DVDD_GPMC
SD2, GP2
PINCNTL117
DSIS: N/A
MM: MUX1
O
IPD
DVDD_GPMC
EMAC[0], UART5
PINCNTL244
DSIS: N/A
MM: MUX0
O
IPU
DVDD
VOUT[1], VIN[1]A,
HDMI, SPI[2], GP3
PINCNTL231
DSIS: N/A
MM: MUX1
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], GPMC,
UART5
PINCNTL243
DSIS: N/A
MM: MUX0
O
O
DESCRIPTION
GPMC Address 1
GPMC Address 0
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-14. GPMC Terminal Functions (continued)
SIGNAL
TYPE (1)
OTHER (2)
(3)
MUXED
NAME
NO.
GPMC_D[15]/
BTMODE[15]
Y25
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL104
DSIS: PIN
GPMC_D[14]/
BTMODE[14]
V24
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL103
DSIS: PIN
GPMC_D[13]/
BTMODE[13]
U23
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL102
DSIS: PIN
GPMC_D[12]/
BTMODE[12]
U24
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL101
DSIS: PIN
GPMC_D[11]/
BTMODE[11]
AA27
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL100
DSIS: PIN
GPMC_D[10]/
BTMODE[10]
Y26
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL99
DSIS: PIN
GPMC_D[9]/
BTMODE[9]
AB28
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL98
DSIS: PIN
GPMC_D[8]/
BTMODE[8]
Y27
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL97
DSIS: PIN
GPMC_D[7]/
BTMODE[7]
V25
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL96
DSIS: PIN
GPMC_D[6]/
BTMODE[6]
U25
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL95
DSIS: PIN
GPMC_D[5]/
BTMODE[5]
AA28
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL94
DSIS: PIN
GPMC_D[4]/
BTMODE[4]
V26
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL93
DSIS: PIN
GPMC_D[3]/
BTMODE[3]
W27
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL92
DSIS: PIN
GPMC_D[2]/
BTMODE[2]
V27
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL91
DSIS: PIN
GPMC_D[1]/
BTMODE[1]
Y28
I/O
DIS
DVDD_GPMCB
BTMODE
PINCNTL90
DSIS: PIN
GPMC_D[0]/
BTMODE[0]
U26
I/O
DIS+
DVDD_GPMCB
BTMODE
PINCNTL89
DSIS: PIN
DESCRIPTION
GPMC Multiplexed Data/Address I/Os.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
93
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.9
www.ti.com
HDMI
Table 3-15. HDMI Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
HDMI_CLKP
AG18
O
–
VDDA_HDMI_
1P8
–
HDMI Clock Output.
HDMI_CLKN
AH18
O
–
VDDA_HDMI_
1P8
–
When the HDMI PHY is powered down, these pins
should be left unconnected.
HDMI_DN2
AH21
O
–
VDDA_HDMI_
1P8
–
HDMI Data 2 output.
–
When the HDMI PHY is powered down, these pins
should be left unconnected.
HDMI_DP2
AG21
O
–
VDDA_HDMI_
1P8
HDMI_DN1
AH20
O
–
VDDA_HDMI_
1P8
–
HDMI Data 1 output.
HDMI_DP1
AG20
O
–
VDDA_HDMI_
1P8
–
When the HDMI PHY is powered down, these pins
should be left unconnected.
HDMI_DN0
AH19
O
–
VDDA_HDMI_
1P8
–
HDMI Data 0 output.
HDMI_DP0
AG19
O
–
VDDA_HDMI_
1P8
–
When the HDMI PHY is powered down, these pins
should be left unconnected.
IPU
DVDD
VOUT[1], GPMC,
VIN[1]ASPI[2],
I2C[2], GP3
PINCNTL228
DSIS: 1
MM: MUX1
VOUT[1]_G_Y_YC[2]/
GPMC_A[13]/
VIN[1]A_D[21]/
HDMI_SCL/
SPI[2]_SCS[2]/
I2C[2]_SCL/
GP3[20]
AF27
I2C[1]_SCL/
HDMI_SCL
AF24
VOUT[1]_R_CR[3]/
GPMC_A[14]/
VIN[1]A_D[22]/
HDMI_SDA/
SPI[2]_SCLK/
I2C[2]_SDA/
GP3[21]
AG28
I2C[1]_SDA/
HDMI_SDA
AG24
(1)
(2)
(3)
94
I/O
I/O
I/O
I/O
DVDD
I2C[1]
PINCNTL78
DSIS: 1
MM: MUX0
IPU
DVDD
VOUT[1], GPMC,
VIN[1]ASPI[2],
I2C[2], GP3
PINCNTL229
DSIS: 1
MM: MUX1
DVDD
HDMI I2C Serial Clock Output
HDMI I2C Serial Data I/O
I2C[1]
PINCNTL79
DSIS: 1
MM: MUX0
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-15. HDMI Terminal Functions (continued)
SIGNAL
NAME
VOUT[1]_B_CB_C[2]/
GPMC_A[0]/
VIN[1]A_D[7]/
HDMI_CEC/
SPI[2]_D[0]/
GP3[30]
GPMC_A[22]/
SPI[2]_D[1]/
HDMI_CEC/
TIM4_IO/
GP1[17]
VOUT[1]_R_CR[2]/
GPMC_A[15]/
VIN[1]A_D[23]/
HDMI_HPDET/
SPI[2]_D[1]/
GP3[22]
GPMC_A[23]/
SPI[2]_SCLK/
HDMI_HPDET/
TIM5_IO/
GP1[18]
NO.
AF28
AB27
AE27
AA26
TYPE (1)
OTHER (2)
IPU
DVDD
IPU
DVDD_GPMC
GPMC, SPI[2],
TIMER4, GP1
PINCNTL111
DSIS: 1
MM: MUX0
IPD
DVDD
VOUT[1], GPMC,
VIN[1]ASPI[2],
GP3
PINCNTL230
DSIS: 0
MM: MUX1
I
I
MUXED
VOUT[1], GPMC,
VIN[1]A, SPI[2],
GP3
PINCNTL231
DSIS: 1
MM: MUX1
I/O
I/O
(3)
IPD
DVDD_GPMC
GPMC, SPI[2],
TIMER5, GP1
PINCNTL112
DSIS: 0
MM: MUX0
DESCRIPTION
HDMI Consumer Electronics Control I/O
HDMI Hot Plug Detect Input. Signals the connection /
removal of an HDMI cable at the connector.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
95
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3.2.10 I2C
Table 3-16. I2C Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
I2C[0]
I2C[0]_SCL
AC4
I/O
DVDD
–
PINCNTL263
I2C[0] Clock I/O. For proper device operation,
this pin must be pulled up via external resistor.
I2C[0]_SDA
AB6
I/O
DVDD
–
PINCNTL264
I2C[0] Data I/O. For proper device operation,
this pin must be pulled up via external resistor.
I2C[1]
I2C[1]_SCL/
HDMI_SCL
AF24
I/O
DVDD
HDMI
PINCNTL78
DSIS: 1
I2C[1] Clock I/O. For proper device operation in
I2C mode, this pin must be pulled up via
external resistor.
I2C[1]_SDA/
HDMI_SDA
AG24
I/O
DVDD
HDMI
PINCNTL79
DSIS: 1
I2C[1] Data I/O. For proper device operation in
I2C mode, this pin must be pulled up via
external resistor.
I/O
IPU
DVDD
VIN[0]A, VIN[0]B,UART5,
GP2
PINCNTL136
DSIS: 1
MM: MUX3
I2C[2]
VIN[0]A_FLD/
VIN[0]B_VSYNC/
UART5_RXD/
I2C[2]_SCL/
GP2[1]
AA20
VOUT[1]_G_Y_YC[2]/
GPMC_A[13]/
VIN[1]A_D[21]/
HDMI_SCL/
SPI[2]_SCS[2]/
I2C[2]_SCL/
GP3[20]
AF27
I/O
IPU
DVDD
VIN[0]A_D[16]/
CAM_D[8]/
I2C[2]_SCL/
GP0[10]
AA21
I/O
IPU
DVDD_C
I/O
IPU
DVDD
UART0_DCD/
UART3_RXD/
SPI[0]_SCS[3]/
I2C[2]_SCL/
SD1_POW/
GP1[2]
(1)
(2)
(3)
96
AH4
VOUT[1], GPMC, VIN[1]A,
HDMI, SPI[2], GP3
PINCNTL228
DSIS: 1
I2C[2] Clock I/O. For proper device operation in
MM: MUX2
I2C mode, this pin must be pulled up via
external resistor.
VIN[0]A, CAM I/F, GP0
PINCNTL156
DSIS: 1
MM: MUX1
UART0, UART3, SPI[0],
SD1, GP1
PINCNTL74
DSIS: 1
MM: MUX0
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and the Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-16. I2C Terminal Functions (continued)
SIGNAL
NAME
EMAC[0]_MTCLK/
EMAC[0]_RGRXC/
VIN[1]B_D[0]/
SPI[3]_SCS[3]/
I2C[2]_SDA/
GP3[23]
NO.
L24
TYPE (1)
OTHER (2)
(3)
I/O
IPD
DVDD_GPMC
MUXED
EMAC[0], VIN[1]B, SPI[3],
GP3
PINCNTL235
DSIS: 1
MM: MUX3
VOUT[1]_R_CR[3]/
GPMC_A[14]/
VIN[1]A_D[22]/
HDMI_SDA/
SPI[2]_SCLK/
I2C[2]_SDA/
GP3[21]
AG28
I/O
IPU
DVDD
VIN[0]A_DE/
VIN[0]B_HSYNC/
UART5_TXD/
I2C[2]_SDA/
GP2[0]
AE21
I/O
IPU
DVDD
I/O
IPU
DVDD
UART0, UART3, SPI[0],
SD1, GP1
PINCNTL75
DSIS: 1
MM: MUX0
I/O
IPD
DVDD
VOUT[1], EMAC[1],
VIN[1]A, GP3
PINCNTL213
DSIS: 1
MM: MUX3
VIN[0]A, CAM I/F,
EMAC[1], GP0
PINCNTL158
DSIS: 1
MM: MUX2
UART0_DSR/
UART3_TXD/
SPI[0]_SCS[2]/
I2C[2]_SDA/
SD1_SDWP/
GP1[3]
AG4
DESCRIPTION
VOUT[1], GPMC, VIN[1]A,
HDMI, SPI[2], GP3
PINCNTL229
DSIS: 1
I2C[2] Data I/O. For proper device operation in
MM: MUX2
I2C mode, this pin must be pulled up via
external resistor.
VIN[0]A, VIN[0]B, UART5,
GP2
PINCNTL135
DSIS: 1
MM: MUX1
I2C3
VOUT[1]_B_CB_C[8]/
EMAC[1]_MRXD[4]/
VIN[1]A_D[5]/
I2C[3]_SCL/
GP3[5]
AH26
VIN[0]A_D[18]/
CAM_D[10]/
EMAC[1]_RMRXD[1]/
I2C[3]_SCL/
GP0[12]
AF20
I/O
IPU
DVDD_C
DCAN0_RX/
UART2_RXD/
I2C[3]_SCL/
GP1[1]
AG6
I/O
IPU
DVDD
DCAN0, UART2, GP1
PINCNTL69
DSIS: 1
MM: MUX1
J1
I/O
IPU
DVDD
MCA[0]
PINCNTL22
DSIS: 1
MM: MUX0
I/O
IPD
DVDD
VOUT[1], EMAC[1],
VIN[1]A, GP3
PINCNTL214
DSIS: 1
MM: MUX3
MCA[0]_AXR[1]/
I2C[3]_SCL
VOUT[1]_B_CB_C[9]/
EMAC[1]_MRXD[5]/
VIN[1]A_D[6]/
I2C[3]_SDA/
GP3[6]
AA24
VIN[0]A_D[19]/
CAM_D[11]/
EMAC[1]_RMRXD[0]/
I2C[3]_SDA/
GP0[13]
AF21
I/O
IPU
DVDD_C
VIN[0]A, CAM I/F,
EMAC[1], GP0
PINCNTL159
DSIS: 1
MM: MUX2
DCAN0_TX/
UART2_TXD/
I2C[3]_SDA/
GP1[0]
AH6
I/O
IPU
DVDD
DCAN0, UART2, GP1
PINCNTL68
DSIS: 1
MM: MUX1
L4
I/O
IPU
DVDD
MCA[0]
PINCNTL23
DSIS: 1
MM: MUX0
MCA[0]_AXR[2]/
I2C[3]_SDA
I2C3 Clock I/O. For proper device operation in
I2C mode, this pin must be pulled up via
external resistor.
I2C3 Data I/O. For proper device operation in
I2C mode, this pin must be pulled up via
external resistor.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
97
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3.2.11 McASP
Table 3-17. McASP0 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
McASP0
MCA[0]_ACLKR/
MCA[5]_AXR[2]
K2
I/O
IPD
DVDD
MCA[5]
PINCNTL19
DSIS: 0
McASP0 Receive Bit Clock I/O
MCA[0]_AFSR/
MCA[5]_AXR[3]
K1
I/O
IPD
DVDD
MCA[5]
PINCNTL20
DSIS: 0
McASP0 Receive Frame Sync I/O
MCA[0]_ACLKX
R4
I/O
IPD
DVDD
–
PINCNTL17
McASP0 Transmit Bit Clock I/O
AUD_CLKIN0/
MCA[0]_AXR[7]/
MCA[0]_AHCLKX/
MCA[3]_AHCLKX/
USB1_DRVVBUS
L5
I/O
IPD
DVDD
AUD_CLKIN0,
MCA[0], MCA[3],
USB1
PINCNTL14
DSIS: PIN
MCA[0]_AFSX
L3
I/O
IPD
DVDD
–
PINCNTL18
AUD_CLKIN2/
MCA[0]_AXR[9]/
MCA[2]_AHCLKX/
MCA[5]_AHCLKX/
EDMA_EVT2/
TIM3_IO/
GP0[9]
H1
I/O
IPD
DVDD
AUD_CLKIN2,
MCA[1], MCA[4],
EDMA, TIMER2,
GP0
PINCNTL16
DSIS: PIN
MM: MUX1
MCA[0]_AXR[9]/
MCB_CLKX/
MCB_CLKR
M6
I/O
IPD
DVDD
MCB
PINCNTL30
DSIS: PIN
MM: MUX0
IPD
DVDD
AUD_CLKIN1,
MCA[1], MCA[4],
EDMA, TIMER2,
GP0
PINCNTL15
DSIS: PIN
MM: MUX1
AUD_CLKIN1/
MCA[0]_AXR[8]/
MCA[1]_AHCLKX/
MCA[4]_AHCLKX/
EDMA_EVT3/
TIM2_IO/
GP0[8]
R5
MCA[0]_AXR[8]/
MCB_FSX/
MCB_FSR
L1
AUD_CLKIN0/
MCA[0]_AXR[7]/
MCA[0]_AHCLKX/
MCA[3]_AHCLKX/
USB1_DRVVBUS
MCA[0]_AXR[7]/
MCB_DX
(1)
(2)
(3)
98
L5
L2
I/O
IPD
DVDD
MCB
PINCNTL29
DSIS: PIN
MM: MUX0
I/O
IPD
DVDD
AUD_CLKIN0,
MCA[0], MCA[3],
USB1
PINCNTL14
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD
MCB
PINCNTL28
DSIS: PIN
MM: MUX0
I/O
McASP0 Transmit High-Frequency Master Clock I/O
McASP0 Transmit Frame Sync I/O
McASP0 Transmit/Receive Data I/Os
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-17. McASP0 Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
MCA[0]_AXR[6]/
MCB_DR
M4
I/O
IPD
DVDD
MCB
PINCNTL27
DSIS: PIN
MCA[0]_AXR[5]/
MCA[1]_AXR[9]
M3
I/O
IPD
DVDD
MCA[1]
PINCNTL26
DSIS: PIN
MCA[0]_AXR[4]/
MCA[1]_AXR[8]
R6
I/O
IPD
DVDD
MCA[1]
PINCNTL25
DSIS: PIN
MCA[0]_AXR[3]/
M5
I/O
IPD
DVDD
PINCNTL24
DSIS: PIN
MCA[0]_AXR[2]/
I2C[3]_SDA
L4
I/O
IPU
DVDD
I2C[3]
PINCNTL23
DSIS: PIN
MCA[0]_AXR[1]/
I2C[3]_SCL
J1
I/O
IPU
DVDD
I2C[3]
PINCNTL22
DSIS: PIN
MCA[0]_AXR[0]
J2
I/O
IPD
DVDD
PINCNTL21
DSIS: PIN
DESCRIPTION
McASP0 Transmit/Receive Data I/Os
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
99
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-18. McASP1 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
McASP1
MCA[1]_ACLKR/
MCA[1]_AXR[4]
M1
I/O
IPD
DVDD
MCA[1]
PINCNTL33
DSIS: 0
McASP1 Receive Bit Clock I/O
MCA[1]_AFSR/
MCA[1]_AXR[5]
M2
I/O
IPD
DVDD
MCA[1]
PINCNTL34
DSIS: 0
McASP1 Receive Frame Sync I/O
MCA[1]_ACLKX
U5
I/O
IPD
DVDD
–
PINCNTL31
McASP1 Transmit Bit Clock I/O
AUD_CLKIN1/
MCA[0]_AXR[8]/
MCA[1]_AHCLKX/
MCA[4]_AHCLKX/
EDMA_EVT3/
TIM2_IO/
GP0[8]
R5
I/O
IPD
DVDD
AUD_CLKIN1,
MCA[0], MCA[4],
EDMA, TIMER2,
GP0
PINCNTL15
DSIS: PIN
MCA[1]_AFSX
V3
I/O
IPD
DVDD
–
PINCNTL32
MCA[3]_AXR[3]/
MCA[1]_AXR[9]/
J6
I/O
IPD
DVDD
MCA[3]
PINCNTL50
DSIS: PIN
MM: MUX1
MCA[0]_AXR[5]/
MCA[1]_AXR[9]
M3
I/O
IPD
DVDD
MCA[0]
PINCNTL26
DSIS: PIN
MM: MUX0
MCA[3]_AXR[2]/
MCA[1]_AXR[8]/
GP0[20]
F2
I/O
IPD
DVDD
MCA[3], GP0
PINCNTL49
DSIS: PIN
MM: MUX1
MCA[0]_AXR[4]/
MCA[1]_AXR[8]
R6
I/O
IPD
DVDD
MCA[0]
PINCNTL25
DSIS: PIN
MM: MUX0
MCA[2]_AXR[3]/
MCA[1]_AXR[7]/
TIM3_IO/
GP0[15]
H2
I/O
IPD
DVDD
MCA[2], TIMER3,
GP0
PINCNTL44
DSIS: PIN
MCA[2], TIMER2,
GP0
PINCNTL43
DSIS: PIN
MCA[2]_AXR[2]/
MCA[1]_AXR[6]/
TIM2_IO/
GP0[14]
V5
I/O
IPD
DVDD
MCA[1]_AFSR/
MCA[1]_AXR[5]
M2
I/O
IPD
DVDD
MCA[1]
PINCNTL34
DSIS: PIN
MCA[1]_ACLKR/
MCA[1]_AXR[4]
M1
I/O
IPD
DVDD
MCA[1]
PINCNTL33
DSIS: PIN
MCA[1]_AXR[3]/
MCB_CLKR
N6
I/O
IPD
DVDD
MCB
PINCNTL38
DSIS: PIN
MCA[1]_AXR[2]/
MCB_FSR
R3
I/O
IPD
DVDD
MCB
PINCNTL37
DSIS: PIN
(1)
(2)
(3)
100
McASP1 Transmit High-Frequency Master Clock I/O
McASP1 Transmit Frame Sync I/O
McASP1 Transmit/Receive Data I/Os
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-18. McASP1 Terminal Functions (continued)
SIGNAL
NAME
MCA[1]_AXR[1]/
SD0_DAT[5]/
MCA[1]_AXR[0]/
SD0_DAT[4]/
NO.
T6
V4
TYPE (1)
OTHER (2)
(3)
MUXED
I/O
IPU
DVDD
SD0
PINCNTL36
DSIS: PIN
I/O
IPU
DVDD
SD0
PINCNTL35
DSIS: PIN
DESCRIPTION
McASP1 Transmit/Receive Data I/Os
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
101
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-19. McASP2 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
McASP2
MCA[2]_ACLKX/
GP0[10]
AUD_CLKIN2/
MCA[0]_AXR[9]/
MCA[2]_AHCLKX/
MCA[5]_AHCLKX/
EDMA_EVT2/
TIM3_IO/
GP0[9]
U6
I/O
IPU
DVDD
GP0
PINCNTL39
DSIS: 0
H1
I/O
IPD
DVDD
AUD_CLKIN2,
MCA[0], MCA[5],
EDMA, TIMER3,
GP0
PINCNTL16
DSIS: PIN
AA5
I/O
IPU
DVDD
GP0
PINCNTL40
DSIS: 0
MCA[2]_AXR[3]/
MCA[1]_AXR[7]/
TIM3_IO/
GP0[15]
H2
I/O
IPD
DVDD
MCA[1], TIMER3,
GP0
PINCNTL44
DSIS: PIN
MCA[2]_AXR[2]/
MCA[1]_AXR[6]/
TIM2_IO/
GP0[14]
V5
I/O
IPD
DVDD
MCA[1], TIMER2,
GP0
PINCNTL43
DSIS: PIN
MCA[2]_AFSX/
GP0[11]
MCA[2]_AXR[1]/
SD0_DAT[7]/
UART5_TXD/
GP0[13]
V6
I/O
IPU
DVDD
SD0, UART5, GP0
PINCNTL42
DSIS: PIN
MCA[2]_AXR[0]/
SD0_DAT[6]/
UART5_RXD/
GP0[12]
N2
I/O
IPU
DVDD
SD0, UART5, GP0
PINCNTL41
DSIS: PIN
(1)
(2)
(3)
102
McASP2 Transmit Bit Clock I/O
McASP2 Transmit High-Frequency Master Clock I/O
McASP2 Transmit Frame Sync I/O
McASP2 Transmit/Receive Data I/Os
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17,Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-20. McASP3 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
McASP3
MCA[3]_ACLKX/
GP0[16]
G6
I/O
IPD
DVDD
GP0
PINCNTL45
DSIS: 0
AUD_CLKIN0,
MCA[0], USB1
PINCNTL14
DSIS: PIN
AUD_CLKIN0/
MCA[0]_AXR[7]/
MCA[0]_AHCLKX/
MCA[3]_AHCLKX/
USB1_DRVVBUS
L5
I/O
IPD
DVDD
MCA[3]_AFSX/
GP0[17]
H4
I/O
IPD
DVDD
GP0
PINCNTL46
DSIS: 0
MCA[3]_AXR[3]/
MCA[1]_AXR[9]/
J6
I/O
IPD
DVDD
MCA[1]
PINCNTL50
DSIS: PIN
MCA[3]_AXR[2]/
MCA[1]_AXR[8]/
GP0[20]
F2
I/O
IPD
DVDD
MCA[1], GP0
PINCNTL49
DSIS: PIN
TIMER5, GP0
PINCNTL48
DSIS: PIN
TIMER4, GP0
PINCNTL47
DSIS: PIN
MCA[3]_AXR[1]/
TIM5_IO/
GP0[19]
G2
I/O
IPD
DVDD
MCA[3]_AXR[0]/
TIM4_IO/
GP0[18]
G1
I/O
IPD
DVDD
(1)
(2)
(3)
McASP3 Transmit Bit Clock I/O
McASP3 Transmit High-Frequency Master Clock I/O
McASP3 Transmit Frame Sync I/O
McASP3 Transmit/Receive Data I/Os
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull before after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
103
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-21. McASP4 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
McASP4
MCA[4]_ACLKX/
GP0[21]
K7
I/O
IPD
DVDD
GP0
PINCNTL51
DSIS: 0
AUD_CLKIN1/
MCA[0]_AXR[8]/
MCA[1]_AHCLKX/
MCA[4]_AHCLKX/
EDMA_EVT3/
TIM2_IO/
GP0[8]
R5
I/O
IPD
DVDD
AUD_CLKIN1,
MCA[0], MCA[1],
EDMA, TIMER2,
GP0
PINCNTL15
DSIS: PIN
MCA[4]_AFSX/
GP0[22]
H3
I/O
IPD
DVDD
GP0
PINCNTL52
DSIS: 0
MCA[5]_AXR[1]/
MCA[4]_AXR[3]/
TIM7_IO/
GP0[28]
L6
I/O
IPD
DVDD
MCA[5], TIMER7,
GP0
PINCNTL58
DSIS: PIN
MCA[5]_AXR[0]/
MCA[4]_AXR[2]/
GP0[27]
L7
I/O
IPD
DVDD
MCA[5], GP0
PINCNTL57
DSIS: PIN
MCA[4]_AXR[1]/
TIM6_IO/
GP0[24]
J4
I/O
IPD
DVDD
TIMER6, GP0
PINCNTL54
DSIS: PIN
MCA[4]_AXR[0]/
GP0[23]
H6
I/O
IPD
DVDD
GP0
PINCNTL53
DSIS: PIN
(1)
(2)
(3)
104
McASP4 Transmit Bit Clock I/O
McASP4 Transmit High-Frequency Master Clock I/O
McASP4 Transmit Frame Sync I/O
McASP4 Transmit/Receive Data I/Os
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-22. McASP5 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
McASP5
MCA[5]_ACLKX/
GP0[25]
J3
I/O
IPD
DVDD
GP0
PINCNTL55
DSIS: 0
AUD_CLKIN2/
MCA[0]_AXR[9]/
MCA[2]_AHCLKX/
MCA[5]_AHCLKX/
EDMA_EVT2/
TIM3_IO/
GP0[9]
H1
I/O
IPD
DVDD
AUD_CLKIN2,
MCA[0], MCA[2],
EDMA, TIMER3,
GP0
PINCNTL16
DSIS: PIN
MCA[5]_AFSX/
GP0[26]
H5
I/O
IPD
DVDD
GP0
PINCNTL56
DSIS: 0
MCA[0]_AFSR/
MCA[5]_AXR[3]
K1
I/O
IPD
DVDD
MCA[0]
PINCNTL20
DSIS: PIN
MCA[0]_ACLKR/
MCA[5]_AXR[2]
K2
I/O
IPD
DVDD
MCA[0]
PINCNTL19
DSIS: PIN
MCA[4], TIMER7,
GP0
PINCNTL58
DSIS: PIN
MCA[4], GP0
PINCNTL57
DSIS: PIN
MCA[5]_AXR[1]/
MCA[4]_AXR[3]/
TIM7_IO/
GP0[28]
L6
I/O
IPD
DVDD
MCA[5]_AXR[0]/
MCA[4]_AXR[2]/
GP0[27]
L7
I/O
IPD
DVDD
(1)
(2)
(3)
McASP5 Transmit Bit Clock I/O
McASP5 Transmit High-Frequency Master Clock I/O
McASP5 Transmit Frame Sync I/O
McASP5 Transmit/Receive Data I/Os
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
105
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3.2.12 McBSP
Table 3-23. McBSP Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
McBSP
MCA[0]_AXR[9]/
MCB_CLKX/
MCB_CLKR
MCA[1]_AXR[3]/
MCB_CLKR
MCA[0]_AXR[8]/
MCB_FSX/
MCB_FSR
M6
N6
L1
I/O
IPD
DVDD
MCA[0], MCB
PINCNTL30
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD
MCA[1]
PINCNTL38
DSIS: PIN
MM: MUX0
I/O
IPD
DVDD
MCA[0], MCB
PINCNTL29
DSIS: PIN
MM: MUX1
McBSP Receive Clock I/O
McBSP Receive Frame Sync I/O
MCA[1]_AXR[2]/
MCB_FSR
R3
I/O
IPD
DVDD
MCA[1], MCB
PINCNTL37
DSIS: PIN
MM: MUX0
MCA[0]_AXR[6]/
MCB_DR
M4
I/O
IPD
DVDD
MCA[0]
PINCNTL27
DSIS: PIN
McBSP Receive Data Input
MCA[0]_AXR[9]/
MCB_CLKX/
MCB_CLKR
M6
I/O
IPD
DVDD
MCA[0], MCB
PINCNTL30
DSIS: PIN
McBSP Transmit Clock I/O
MCA[0]_AXR[8]/
MCB_FSX/
MCB_FSR
L1
I/O
IPD
DVDD
MCA[0], MCB
PINCNTL29
DSIS: PIN
McBSP Transmit Frame Sync I/O
MCA[0]_AXR[7]/
MCB_DX
L2
I/O
IPD
DVDD
MCA[0]
PINCNTL28
DSIS: PIN
(1)
(2)
(3)
106
McBSP Transmit Data Output
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.13 PCI Express (PCIe)
Table 3-24. PCI Express (PCIe) Terminal Functions
SIGNAL
NAME
PCIE_TXP0
NO.
AD2
TYPE (1)
OTHER (2)
(3)
O
PCIE_TXN0
AD1
O
PCIE_RXP0
AC2
I
PCIE Transmit Data Lane 0.
–
VDDA_PCIE_1P8
AC1
I
SERDES_CLKP
AF1
I
–
SERDES_CLK LDO
(internal)
SERDES_CLKN
AF2
I
–
SERDES_CLK LDO
(internal)
(2)
(3)
When the PCIe SERDES are powered down, these pins should be
left unconnected.
PCIE Receive Data Lane 0.
–
VDDA_PCIE_1P8
PCIE_RXN0
(1)
DESCRIPTION
When the PCIe SERDES are powered down, these pins should be
left unconnected.
PCIE Serdes Reference Clock Inputs and optional SATA
Reference Clock Inputs.
Shared between PCI Express and Serial ATA. When PCI Express
is not used, and these pins are not used as optional SATA
Reference Clock Inputs, these pins can be left unconnected.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
107
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3.2.14 Reset, Interrupts, and JTAG Interface
Table 3-25. RESET, Interrupts, and JTAG Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
RESET
RESET
J5
I
IPU
DVDD
–
Device Reset input
PINCNTL260
POR
F1
I
–
DVDD
RSTOUT_WD_OUT
K6
O
DIS
DVDD
I
IPU
DVDD
I/O
see
NOTE
see
Table 3-10
Interrupt-capable general-purpose I/Os.
NOTE: All pins are multiplexed with other pin functions.
See Table 3-10, GP0 Terminal Functions table for muxing
and internal pullup/pulldown/disable details.
see
Table 3-11
Interrupt-capable general-purpose I/Os.
NOTE: All pins are multiplexed with other pin functions.
See Table 3-11, GP1 Terminal Functions table for muxing
and internal pullup/pulldown/disable details.
–
Power-On Reset input
Reset output (RSTOUT) or watchdog out (WD_OUT)
–
PINCNTL262 For more detailed information on RSTOUT_WD_OUT pin
behavior, see Section 7.3.14, RSTOUT_WD_OUT Pin.
INTERRUPTS
NMI
H7
–
Non-Maskable Interrupt input
PINCNTL261
GP0[31:0]
see
Table 3-10
GP1[31:0]
see
Table 3-11
I/O
see
NOTE
GP2[31:0]
see
Table 3-12
I/O
see
NOTE
see
Table 3-12
Interrupt-capable general-purpose I/Os.
NOTE: All pins are multiplexed with other pin functions.
See Table 3-12, GP2 Terminal Functions table for muxing
and internal pullup/pulldown/disable details.
GP3[31:0]
see
Table 3-13
I/O
see
NOTE
see
Table 3-13
Interrupt-capable general-purpose I/Os.
NOTE: All pins are multiplexed with other pin functions.
See Table 3-13, GP3 Terminal Functions table for muxing
and internal pullup/pulldown/disable details.
I
IPU
DVDD
AD4
TDI
JTAG
TCLK
W7
–
JTAG test clock input
O
IPU/DIS
DVDD
–
JTAG return clock output
The internal pullup (IPU) is enabled for this pin when the
device is in reset and the IPU is disabled (DIS) when reset
is released.
Y7
I
IPU
DVDD
–
JTAG test data input
TDO
AC5
O
IPU
DVDD
–
JTAG test port data output
TMS
AA7
I
IPU
DVDD
–
JTAG test port mode select input. For proper operation, do
not oppose the IPU on this pin.
TRST
AA4
I
IPD
DVDD
–
JTAG test port reset input
VOUT[0]_R_CR[2]/
EMU4/
GP2[26]
AD9
I/O
IPD
DVDD
VOUT[0],
GP2
Emulator pin 4
PINCNTL196
DSIS: PIN
VOUT[0]_G_Y_YC[2]/
EMU3/
GP2[24]
AH7
I/O
IPD
DVDD
VOUT[0],
GP2
Emulator pin 3
PINCNTL188
DSIS: PIN
RTCK
(1)
(2)
(3)
108
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-25. RESET, Interrupts, and JTAG Terminal Functions (continued)
SIGNAL
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
NAME
NO.
VOUT[0]_B_CB_C[2]/
EMU2/
GP2[22]
AG7
I/O
IPD
DVDD
EMU1
AE11
I/O
IPU
DVDD
–
Emulator pin 1
EMU0
AG8
I/O
IPU
DVDD
–
Emulator pin 0
VOUT[0],
GP0
Emulator pin 2
PINCNTL180
DSIS: PIN
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
109
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3.2.15 Serial ATA (SATA) Signals
Table 3-26. Serial ATA (SATA) Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
SATA_TXN0
AB1
O
–
VDDA_SATA_1P8
–
Serial ATA Data Transmit.
SATA_TXP0
AB2
O
–
VDDA_SATA_1P8
–
When the SATA SERDES are powered down, these
pins should be left unconnected.
SATA_RXN0
AA2
I
–
VDDA_SATA_1P8
–
Serial ATA Data Receive.
SATA_RXP0
AA1
I
–
VDDA_SATA_1P8
–
When the SATA SERDES are powered down, these
pins should be left unconnected.
SPI[0]_SCS[1]/
SD1_SDCD/
SATA_ACT0_LED/
EDMA_EVT1/
TIM4_IO/
GP1[6]
AE5
O
IPU
DVDD
SERDES_CLKP
AF1
I
–
SERDES_CLK
LDO (internal)
–
SERDES_CLKN
AF2
I
–
SERDES_CLK
LDO (internal)
–
(1)
(2)
(3)
110
SPI[0], SD1,
EDMA, TIMER 4,
GP1
Serial ATA disk 0 Activity LED output
PINCNTL80
DSIS: N/A
PCIE Serdes Reference Clock Inputs and optional
SATA Reference Clock Inputs.
Shared between PCI Express and Serial ATA. When
PCI Express is not used, and these pins are not used
as optional SATA Reference Clock Inputs, these pins
should be left unconnected.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.16 SD Signals (MMC/SD/SDIO)
Table 3-27. SD0 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
SD0_CLK/
GP0[1]
Y6
O
IPU
DVDD_SD
GP0
PINCNTL8
DSIS: 1
SD0 Clock output
SD0_CMD/
SD1_CMD/
GP0[2]
N1
I/O
IPU
DVDD_SD
SD1, GP0
PINCNTL9
DSIS: 1
SD0 Command input/output
SD0_DAT[0]/
SD1_DAT[4]/
GP0[3]
R7
I/O
IPU
DVDD_SD
SD1, GP0
PINCNTL10
DSIS: PIN
SD0 Data0 I/O. Functions as data bit 0 for 4-/8-bit SD mode
and single data bit for 1-bit SD mode.
SD0_DAT[1]_SDIRQ/
SD1_DAT[5]/
GP0[4]
Y5
I/O
IPU
DVDD_SD
SD1, GP0
PINCNTL11
DSIS: PIN
SD0 Data1 I/O. Functions as data bit 1 for 4-/8-bit SD mode
and as an IRQ input for 1-bit SD mode.
SD0_DAT[2]_SDRW/
SD1_DAT[6]/
GP0[5]
Y3
I/O
IPU
DVDD_SD
SD1, GP0
PINCNTL12
DSIS: PIN
SD0 Data2 I/O. Functions as data bit 2 for 4-/8-bit SD mode
and as a Read Wait input for 1-bit SD mode.
SD0_DAT[3]/
SD1_DAT[7]/
GP0[6]
Y4
I/O
IPU
DVDD_SD
SD1, GP0
PINCNTL13
DSIS: PIN
SD0 Data3 I/O. Functions as data bit 3 for 4-/8-bit SD mode.
MCA[1]_AXR[0]/
SD0_DAT[4]/
V4
I/O
IPU
DVDD
MCA[1]
PINCNTL35
DSIS: PIN
SD0 Data4 I/O. Functions as data bit 4 for 8-bit SD mode.
MCA[1]_AXR[1]/
SD0_DAT[5]/
T6
I/O
IPU
DVDD
MCA[1], SC0
PINCNTL36
DSIS: PIN
SD0 Data5 I/O. Functions as data bit 5 for 8-bit SD mode.
I/O
IPU
DVDD
MCA[2], UART5,
GP0
PINCNTL41
DSIS: PIN
SD0 Data6 I/O. Functions as data bit 6 for 8-bit SD mode.
I/O
IPU
DVDD
MCA[2], UART5,
GP0
PINCNTL42
DSIS: PIN
SD0 Data7 I/O. Functions as data bit 7 for 8-bit SD mode.
I
IPD
DVDD
UART0, UART4,
DCAN1, SPI[1]
PINCNTL72
DSIS: 1
SD0 Card Detect input
MCA[2]_AXR[0]/
SD0_DAT[6]/
UART5_RXD/
GP0[12]
MCA[2]_AXR[1]/
SD0_DAT[7]/
UART5_TXD/
GP0[13]
UART0_CTS/
UART4_RXD/
DCAN1_TX/
SPI[1]_SCS[3]/
SD0_SDCD
(1)
(2)
(3)
N2
V6
AE6
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
111
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-28. SD1 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
SD1_CLK
P3
O
IPU
DVDD_SD
–
PINCNTL1
DSIS: N/A
SD0_CMD/
SD1_CMD/
GP0[2]
N1
I/O
IPU
DVDD_SD
SD0, GP0
PINCNTL9
DSIS: N/A
MM: MUX1
DESCRIPTION
SD1 Clock output
SD1 Command input/output
SD1_CMD/
GP0[0]
P2
I/O
IPU
DVDD_SD
GP1
PINCNTL2
DSIS: N/A
MM: MUX0
SD1_DAT[0]
P1
I/O
IPU
DVDD_SD
–
PINCNTL3
SD1 Data0 I/O. Functions as data bit 0 for 4-/8-bit SD mode
and single data bit for 1-bit SD mode.
SD1_DAT[1]_SDIRQ
P5
I/O
IPU
DVDD_SD
–
PINCNTL4
SD1 Data1 I/O. Functions as data bit 1 for 4-/8-bit SD mode
and as an IRQ input for 1-bit SD mode.
SD1_DAT[2]_SDRW
P4
I/O
IPU
DVDD_SD
–
PINCNTL5
SD1 Data2 I/O. Functions as data bit 2 for 4-/8-bit SD mode
and as a Read Wait input for 1-bit SD mode.
SD1_DAT[3]
P6
I/O
IPU
DVDD_SD
–
PINCNTL6
SD1 Data3 I/O. Functions as data bit 3 for 4-/8-bit SD mode.
SD0_DAT[0]/
SD1_DAT[4]/
GP0[3]
R7
I/O
IPU
DVDD_SD
SD0, GP0
PINCNTL10
DSIS: PIN
SD1 Data4 I/O. Functions as data bit 4 for 8-bit SD mode.
SD0_DAT[1]_SDIRQ/
SD1_DAT[5]/
GP0[4]
Y5
I/O
IPU
DVDD_SD
SD0, GP0
PINCNTL11
DSIS: PIN
SD1 Data5 I/O. Functions as data bit 5 for 8-bit SD mode.
SD0_DAT[2]_SDRW/
SD1_DAT[6]/
GP0[5]
Y3
I/O
IPU
DVDD_SD
SD0, GP0
PINCNTL12
DSIS: PIN
SD1 Data6 I/O. Functions as data bit 6 for 8-bit SD mode.
SD0_DAT[3]/
SD1_DAT[7]/
GP0[6]
Y4
I/O
IPU
DVDD_SD
SD0, GP0
PINCNTL13
DSIS: PIN
SD1 Data7 I/O. Functions as data bit 7 for 8-bit SD mode.
AH4
O
IPU
DVDD
UART0, UART3,
SPI[0], I2C[2], GP1
SD1 Card Power Enable output
PINCNTL74
DSIS: PIN
SPI[0], SATA,
EDMA, TIM4, GP1
SD1 Card Detect input
PINCNTL80
DSIS: 1
UART0, UART3,
SPI[0], I2C[2], GP1
SD1 Card Write Protect input
PINCNTL75
DSIS: 0
UART0_DCD/
UART3_RXD/
SPI[0]_SCS[3]/
I2C[2]_SCL/
SD1_POW/
GP1[2]
SPI[0]_SCS[1]/
SD1_SDCD/
SATA_ACT0_LED/
EDMA_EVT1/
TIM4_IO/
GP1[6]
AE5
I
IPU
DVDD
UART0_DSR/
UART3_TXD/
SPI[0]_SCS[2]/
I2C[2]_SDA/
SD1_SDWP/
GP1[3]
AG4
I
IPU
DVDD
(1)
(2)
(3)
112
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-29. SD2 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
SD2_SCLK/
GP1[15]
M23
O
IPU
DVDD_GPMC
GP1
PINCNTL121
DSIS: N/A
SD2 Clock output
GPMC_CS[4]/
SD2_CMD/
GP1[8]
P25
I/O
IPU
DVDD_GPMC
GPMC, GP1
PINCNTL126
DSIS: N/A
SD2 Command input/output
SD2_DAT[0]/
GPMC_A[4]/
GP1[14]
L26
I/O
IPU
DVDD_GPMC
GPMC, GP1
PINCNTL120
DSIS: PIN
SD2 Data0 I/O. Functions as data bit 0 for 4-/8-bit SD
mode and single data bit for 1-bit SD mode.
SD2_DAT[1]_SDIRQ/
GPMC_A[3]/
GP1[13]
M24
I/O
IPU
DVDD_GPMC
GMPC, GP1
PINCNTL119
DSIS: PIN
SD2 Data1 I/O. Functions as data bit 1 for 4-/8-bit SD
mode and as an IRQ input for 1-bit SD mode
SD2_DAT[2]_SDRW/
GPMC_A[2]/
GP2[6]
K27
I/O
IPU
DVDD_GPMC
GPMC, GP2
PINCNTL118
DSIS: PIN
SD2 Data2 I/O. Functions as data bit 2 for 4-/8-bit SD
mode and as a Read Wait input for 1-bit SD mode.
SD2_DAT[3]/
GPMC_A[1]/
GP2[5]
J28
I/O
IPU
DVDD_GPMC
GPMC, GP2
PINCNTL117
DSIS: PIN
SD2 Data3 I/O. Functions as data bit 3 for 4-/8-bit SD
mode.
GPMC, EDMA,
TIM7, GP1
PINCNTL116
DSIS: PIN
SD2 Data4 I/O. Functions as data bit 4 for 8-bit SD mode.
SD2_DAT[4]/
GPMC_A[27]/
GPMC_A[23]/
GPMC_CS[7]/
EDMA_EVT0/
TIM7_IO/
GP1[22]
R24
I/O
IPU
DVDD_GPMC
SD2_DAT[5]/
GPMC_A[26]/
GPMC_A[22]/
TIM6_IO/
GP1[21]
P22
I/O
IPU
DVDD_GPMC
GPMC, TIM6,
GP1
PINCNTL115
DSIS: PIN
SD2 Data5 I/O. Functions as data bit 5 for 8-bit SD mode.
I/O
IPU
DVDD_GPMC
GPMC, UART2,
GP1
PINCNTL114
DSIS: PIN
SD2 Data6 I/O. Functions as data bit 6 for 8-bit SD mode.
GPMC, UART2,
GP1
PINCNTL113
DSIS: PIN
SD2 Data7 I/O. Functions as data bit 7 for 8-bit SD mode.
UART0, UART4,
DCAN1, SPI[1]
PINCNTL73
DSIS: 1
SD2 Card Detect input.
SD2_DAT[6]/
GPMC_A[25]/
GPMC_A[21]/
UART2_TXD/
GP1[20]
N23
SD2_DAT[7]/
GPMC_A[24]/
GPMC_A[20]/
UART2_RXD/
GP1[19]
L25
I/O
IPU
DVDD_GPMC
UART0_RTS/
UART4_TXD/
DCAN1_RX/
SPI[1]_SCS[2]/
SD2_SDCD
AF5
I
IPD
DVDD
(1)
(2)
(3)
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
113
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3.2.17 SPI
Table 3-30. SPI 0 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
SPI[0]_SCLK
AC7
I/O
IPU
DVDD
–
PINCNTL82
UART0_DCD/
UART3_RXD/
SPI[0]_SCS[3]/
I2C[2]_SCL/
SD1_POW/
GP1[2]
AH4
I/O
IPU
DVDD
UART0, UART3,
I2C[2], SD1, GP1
PINCNTL74
DSIS: PIN
I/O
IPU
DVDD
UART0, UART3,
I2C[2], SD1, GP1
PINCNTL75
DSIS: PIN
SD1, SATA,
EDMA, TIMER4,
GP1
PINCNTL80
DSIS: PIN
UART0_DSR/
UART3_TXD/
SPI[0]_SCS[2]/
I2C[2]_SDA/
SD1_SDWP/
GP1[3]
AG4
SPI[0]_SCS[1]/
SD1_SDCD/
SATA_ACT0_LED/
EDMA_EVT1/
TIM4_IO/
GP1[6]
AE5
I/O
IPU
DVDD
SPI[0]_SCS[0]
AD6
I/O
IPU
DVDD
–
PINCNTL81
SPI[0]_D[1]
AF3
I/O
IPU
DVDD
–
PINCNTL83
SPI[0]_D[0]
AE3
I/O
IPU
DVDD
–
PINCNTL84
(1)
(2)
(3)
114
DESCRIPTION
SPI Clock I/O
SPI Chip Select I/O
SPI Data I/O. Can be configured as either MISO or MOSI
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-31. SPI 1 Terminal Functions
SIGNAL
NAME
NO.
SPI[1]_SCLK/
GP1[17]
AC3
UART0_CTS/
UART4_RXD/
DCAN1_TX/
SPI[1]_SCS[3]/
SD0_SDCD
AE6
TYPE (1)
OTHER (2)
(3)
MUXED
I/O
IPU
DVDD
GP1
PINCNTL86
DSIS: PIN
I/O
IPU
DVDD
UART0, UART4,
DCAN1, SD0
PINCNTL72
DSIS: PIN
I/O
IPU
DVDD
UART0, UART4,
DCAN1, SD2
PINCNTL73
DSIS: PIN
UART0_RTS/
UART4_TXD/
DCAN1_RX/
SPI[1]_SCS[2]/
SD2_SDCD
AF5
DEVOSC_WAKE/
SPI[1]_SCS[1]/
TIM5_IO/
GP1[7]
W6
I/O
IPU
DVDD_SD
DEVOSC,
TIMER5, GP1
PINCNTL7
DSIS: PIN
SPI[1]_SCS[0]/
GP1[16]
AD3
I/O
IPU
DVDD
GP1
PINCNTL85
DSIS: PIN
SPI[1]_D[1]/
GP1[18]
AA3
I/O
IPU
DVDD
GP1
PINCNTL87
DSIS: PIN
SPI[1]_D[0]/
GP1[26]
AA6
I/O
IPU
DVDD
GP1
PINCNTL88
DSIS: PIN
(1)
(2)
(3)
DESCRIPTION
SPI Clock I/O
SPI Chip Select I/O
SPI Data I/O. Can be configured as either MISO or MOSI
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
115
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-32. SPI 2 Terminal Functions
SIGNAL
NAME
EMAC[0]_MRXDV/
EMAC[1]_RGRXD[1]/
GPMC_A[5]/
SPI[2]_SCLK
VOUT[1]_R_CR[3]/
GPMC_A[14]/
VIN[1]A_D[22]/
HDMI_SDA/
SPI[2]_SCLK/
I2C[2]_SDA/
GP3[21]
NO.
K22
AG28
TYPE (1)
I/O
I/O
OTHER (2)
(3)
IPD
DVDD_GPMC
IPU
DVDD
MUXED
EMAC[0],
EMAC[1], GPMC
PINCNTL248
DSIS: 1
MM: MUX2
VOUT[1], GPMC,
VIN[1]A, HDMI,
I2C[2], GP3
SPI Clock I/O
PINCNTL229
DSIS: 1
MM: MUX1
GPMC_A[23]/
SPI[2]_SCLK/
HDMI_HPDET/
TIM5_IO/
GP1[18]
AA26
I/O
IPD
DVDD_GPMC
GPMC, HDMI,
TIMER5, GP1
PINCNTL112
DSIS: 1
MM: MUX0
EMAC[0]_MRXD[7]/
EMAC[0]_RGTXD[1]/
GPMC_A[4]/
SPI[2]_SCS[3]/
G27
I/O
IPD
DVDD_GPMC
EMAC[0], GPMC
PINCNTL247
DSIS: 1
I/O
IPU
DVDD
VOUT[1].
VIN[1]A, HDMI,
I2C[2], GP3
PINCNTL228
DSIS: 1
VOUT[1]_G_Y_YC[2]/
GPMC_A[13]/
VIN[1]A_D[21]/
HDMI_SCL/
SPI[2]_SCS[2]/
I2C[2]_SCL/
GP3[20]
AF27
GPMC_A[20]/
SPI[2]_SCS[1]/
GP1[15]
AD28
GPMC_CS[3]/
VIN[1]B_CLK/
SPI[2]_SCS[0]/
GP1[26]
(1)
(2)
(3)
116
P26
DESCRIPTION
I/O
IPU
DVDD_GPMC
GPMC, GP1
PINCNTL109
DSIS: 1
I/O
IPU
DVDD_GPMC
GPMC, VIN[1]B,
GP1
PINCNTL125
DSIS: 1
SPI Chip Select I/O
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-32. SPI 2 Terminal Functions (continued)
SIGNAL
NAME
EMAC[0]_GMTCLK/
EMAC[1]_RGRXC/
GPMC_A[6]/
SPI[2]_D[1]
VOUT[1]_R_CR[2]/
GPMC_A[15]/
VIN[1]A_D[23]/
HDMI_HPDET/
SPI[2]_D[1]/
GP3[22]
GPMC_A[22]/
SPI[2]_D[1]/
HDMI_CEC/
TIM4_IO/
GP1[17]
EMAC[0]_MTXD[0]/
EMAC[1]_RGRXD[3]/
GPMC_A[7]/
SPI[2]_D[0]
NO.
K23
AE27
AB27
J24
TYPE (1)
OTHER (2)
(3)
MUXED
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], GPMC
PINCNTL249
DSIS: PIN
MM: MUX2
I/O
IPD
DVDD
VOUT[1], GPMC,
VIN[1]A, HDMI,
GP3
PINCNTL230
DSIS: PIN
MM: MUX1
I/O
IPU
DVDD_GPMC
GPMC, HDMI,
TIMER 4, GP1
PINCNTL111
DSIS: PIN
MM: MUX0
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], GPMC
PINCNTL250
DSIS: PIN
MM: MUX2
I/O
I/O
VOUT[1]_B_CB_C[2]/
GPMC_A[0]/
VIN[1]A_D[7]/
HDMI_CEC/
SPI[2]_D[0]/
GP3[30]
AF28
I/O
IPU
DVDD
VOUT[1], GPMC,
VIN[1]A, HDMI,
GP3
PINCNTL231
DSIS: PIN
MM: MUX1
GPMC_A[21]/
SPI[2]_D[0]/
GP1[16]
AC28
I/O
IPD
DVDD_GPMC
GPMC, GP1
PINCNTL110
DSIS: PIN
MM: MUX0
DESCRIPTION
SPI Data I/O. Can be configured as either MISO or MOSI
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
117
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-33. SPI 3 Terminal Functions
SIGNAL
NAME
VOUT[0]_AVID/
VOUT[0]_FLD/
SPI[3]_SCLK/
TIM7_IO/
GP2[21]
VOUT[1]_R_CR[5]/
EMAC[1]_MTXD[4]/
VIN[1]A_D[16]/
SPI[3]_SCLK/
GP3[15]
VIN[0]A_D[21]/
CAM_D[13]/
EMAC[1]_RMTXD[0]/
SPI[3]_SCLK/
GP0[15]
EMAC[0]_MTCLK/
EMAC[0]_RGRXC/
VIN[1]B_D[0]/
SPI[3]_SCS[3]/
I2C[2]_SDA/
GP3[23]
EMAC[0]_MRCLK/
EMAC[0]_RGTXC/
VIN[1]B_D[4]/
EMAC[0]_RMCRSDV/
SPI[3]_SCS[2]/
GP3[27]
VOUT[1]_R_CR[4]/
EMAC[1]_MTXD[3]/
VIN[1]A_D[15]/
SPI[3]_SCS[1]/
GP3[14]
VIN[0]A_D[20]/
CAM_D[12]/
EMAC[1]_RMCRSDV/
SPI[3]_SCS[0]/
GP0[14]
(1)
(2)
(3)
118
NO.
AA10
AC26
AE18
L24
H27
TYPE (1)
OTHER (2)
(3)
MUXED
IPD
DVDD
VOUT[0], TIMER
7, GP2
PINCNTL179
DSIS: 1
MM: MUX2
IPD
DVDD
VOUT[0],
EMAC[1],
VIN[1]A, GP3
PINCNTL223
DSIS: 1
MM: MUX1
I/O
IPD
DVDD_C
VIN[0]A,
CAMERA_I/F,
EMAC[1], GP0
PINCNTL161
DSIS: 1
MM: MUX0
I/O
IPD
DVDD
EMAC[0],
VIN[1]B, I2C[2],
GP3
PINCNTL235
DSIS: 1
I/O
IPD
DVDD_GPMC
EMAC[0],
VIN[1]B, GP3
PINCNTL239
DSIS: 1
IPD
DVDD
VOUT[1].
EMAC[1],
VIN[1]A, GP3
PINCNTL222
DSIS: 1
IPD
DVDD_C
VIN[0]A,
CAMERA,_I/F,
EMAC[1]_RM,
GP0
PINCNTL160
DSIS: 1
I/O
I/O
DESCRIPTION
SPI Clock I/O
SPI Chip Select I/O
AG27
AC17
I/O
I/O
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-33. SPI 3 Terminal Functions (continued)
SIGNAL
NAME
VOUT[1]_HSYNC/
EMAC[1]_MCOL/
VIN[1]A_VSYNC/
SPI[3]_D[1]/
UART3_RTS/
GP2[29]
VOUT[1]_R_CR[6]/
EMAC[1]_MTXD[5]/
VIN[1]A_D[17]/
SPI[3]_D[1]/
GP3[16]
VIN[0]A_D[22]/
CAM_D[14]/
EMAC[1]_RMTXD[1]/
SPI[3]_D[1]/
GP0[16]
VOUT[1]_VSYNC/
EMAC[1]_MCRS/
VIN[1]A_FLD/
VIN[1]A_DE/
SPI[3]_D[0]/
UART3_CTS/
GP2[30]
VOUT[1]_R_CR[7]/
EMAC[1]_MTXD[6]/
VIN[1]A_D[18]/
SPI[3]_D[0]/
GP3[17]
VIN[0]A_D[23]/
CAM_D[15]/
EMAC[1]_RMTXEN/
SPI[3]_D[0]/
GP0[17]
NO.
AC24
AA25
AC21
AA23
V22
AC16
TYPE (1)
I/O
I/O
I/O
I/O
I/O
I/O
OTHER (2)
(3)
MUXED
IPD
DVDD
VOUT[1],
EMAC[1],
VIN[1]A, UART3,
GP2
PINCNTL205
DSIS: PIN
MM: MUX2
IPD
DVDD
VOUT[1],
EMAC[1],
VIN[1]A, GP3
PINCNTL224
DSIS: PIN
MM: MUX1
IPD
DVDD_C
VIN[0]A,
CAMERA_I/F,
EMAC[1]_RM,
GP0
PINCNTL162
DSIS: PIN
MM: MUX0
IPD
DVDD
VOUT[1],
EMAC[1],
VIN[1]A, UART3,
GP2
PINCNTL206
DSIS: PIN
MM: MUX2
IPD
DVDD
VOUT[1],
EMAC[1],
VIN[1]A, GP3
PINCNTL225
DSIS: PIN
MM: MUX1
IPD
DVDD_C
VIN[0]A,
CAMERA_I/F,
EMAC[1], GP0
PINCNTL163
DSIS: PIN
MM: MUX0
DESCRIPTION
SPI Data I/O. Can be configured as either MISO or MOSI
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
119
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3.2.18 Oscillator/PLL, Audio Reference Clocks, and Clock Generator
Table 3-34. Oscillator/PLL, Audio Reference Clocks, and Clock Generator Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
CLOCK GENERATOR
VIN[0]A_D[12]_BD[4]/
CLKOUT1/
GP2[17]
GPMC_CLK/
GPMC_CS[5]/
GPMC_WAIT[1]/
CLKOUT1/
EDMA_EVT3/
TIM4_IO/
GP1[27]
VIN[0]B_CLK/
CLKOUT0/
GP1[9]
CLKIN32/
CLKOUT0/
TIM3_IO/
GP3[31]
AG17
I/O
IPD
DVDD
VIN[0]A, GP2
PINCNTL152
DSIS: PIN
R26
O
IPU
DVDD_GPMC
GPMC, EDMA,
TIM4, GP1
PINCNTL127
DSIS: N/A
AE17
I/O
IPD
DVDD
VIN[0]B, GP1
PINCNTL134
DSIS: PIN
IPD
DVDD
CLKIN32, TIM3,
GP3
PINCNTL259
DSIS: N/A
J7
O
Device Clock output 1. Can be used as a system clock
for other devices.
Device Clock output 0. Can be used as a system clock
for other devices.
OSCILLATOR/PLL
DEVOSC_MXI/
DEV_CLKIN
AH2
AI
–
VDDA_1P8
–
Device Crystal input. Crystal connection to internal
oscillator for system clock. Functions as DEV_CLKIN
clock input when an external oscillator is used.
DEVOSC_MXO
AH3
AO
–
VDDA_1P8
–
Device Crystal output. Crystal connection to internal
oscillator for system clock. When device oscillator is
BYPASSED, leave this pin unconnected.
VSSA_DEVOSC
AG3
GND
Supply Ground for DEV Oscillator. If the internal
oscillator is bypassed, DEVOSC_VSS should be
connected to ground (VSS).
AI
–
VDDA_1P8
–
Auxiliary Crystal input [Optional Audio/Video Reference
Crystal Input]. Crystal connection to internal oscillator
for auxiliary clock. Functions as AUX_CLKIN clock input
when an external oscillator is used.
T1
AO
–
VDDA_1P8
–
Auxiliary Crystal output [Optional Audio/Video
Reference Crystal Output]. When auxiliary oscillator is
BYPASSED, leave this pin unconnected.
VSSA_AUXOSC
R2
GND
CLKIN32/
CLKOUT0/
TIM3_IO/
GP3[31]
J7
I
IPD
DVDD
CLKOUT0,
TIMER 3, GP3
PINCNTL259
DSIS: PIN
DEVOSC_WAKE/
SPI[1]_SCS[1]/
TIM5_IO/
GP1[7]
W6
I
IPU
DVDD_SD
SPI[1], TIMER 5,
GP1
PINCNTL7
DSIS: 1
AUXOSC_MXI/
AUX_CLKIN
R1
AUXOSC_MXO
(1)
(2)
(3)
120
Supply Ground for AUX Oscillator. If the internal
oscillator is bypassed, AUXOSC_VSS should be
connected to ground (VSS).
RTC Clock input. Optional 32.768 KHz clock for RTC
reference.
Oscillator Wake-up input.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull during and after Reset. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-34. Oscillator/PLL, Audio Reference Clocks, and Clock Generator Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
AUDIO REFERENCE CLOCKS
AUD_CLKIN2/
MCA[0]_AXR[9]/
MCA[2]_AHCLKX/
MCA[5]_AHCLKX/
EDMA_EVT2/
TIM3_IO/
GP0[9]
H1
I
IPD
DVDD
MCA[0], MCA[2],
MCA[5], EDMA,
TIMER 3, GP0
PINCNTL16
DSIS: PIN
MCA[0], MCA[1],
MCA[4], EDMA,
TIMER 2, GP0
PINCNTL15
DSIS: PIN
Audio Reference Clock 1 for Audio Peripherals.
MCA[0], MCA[3],
USB1
PINCNTL14
DSIS: PIN
Audio Reference Clock 0 for Audio Peripherals.
AUD_CLKIN1/
MCA[0]_AXR[8]/
MCA[1]_AHCLKX/
MCA[4]_AHCLKX/
EDMA_EVT3/
TIM2_IO/
GP0[8]
R5
I
IPD
DVDD
AUD_CLKIN0/
MCA[0]_AXR[7]/
MCA[0]_AHCLKX/
MCA[3]_AHCLKX/US
B1_DRVVBUS
L5
I
IPD
DVDD
Audio Reference Clock 2 for Audio Peripherals.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
121
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3.2.19 Timer
Table 3-35. Timer Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
Timers 8-1 and Watchdog Timer 0
Timer 8 and Timer1
There are no external pins for these timers.
Timers TCLKIN
TCLKIN/
GP0[30]
T2
IPD
DVDD
GP0
PINCNTL60
DSIS: 0
I/O
IPD
DVDD_GPMC
GPMC, EDMA,
GP1
PINCNTL132
DSIS: PIN
MM: MUX3
I/O
IPU
DVDD_GPMC
SD2, GPMC,
EDMA, GP1
PINCNTL116
DSIS: PIN
MM: MUX2
I
Timer external clock input
Timer 7
GPMC_BE[1]/
GPMC_A[24]/
EDMA_EVT1/
TIM7_IO/
GP1[30]
SD2_DAT4
GPMC_A[27]/
GPMC_A[23]/
GPMC_CS[7]/
EDMA_EVT0/
TIM7_IO/
GP1[22]
VOUT[0]_AVID/
VOUT[0]_FLD/
SPI[3]_SCLK/
TIM7_IO/
GP2[21]
MCA[5]_AXR[1]/
MCA[4]_AXR[3]/
TIM7_IO/
GP0[28]
V28
R24
AA10
L6
I/O
IPD
DVDD
VOUT[0], SPI[3],
GP2
PINCNTL179
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD
MCA[5], MCA[4],
GP0
PINCNTL58
DSIS: PIN
MM: MUX0
Timer 7 capture event input or PWM output
Timer 6
GPMC_BE[0]_CLE/
GPMC_A[25]/
EDMA_EVT2/
TIM6_IO/
GP1[29]
U27
I/O
IPD
DVDD_GPMC
GPMC, EDMA,
GP1
PINCNTL131
DSIS: PIN
MM: MUX3
SD2_DAT[5]/
GPMC_A[26]/
GPMC_A[22]/
TIM6_IO/
GP1[21]
P22
I/O
IPU
DVDD_GPMC
SD2, GPMC, GP1
PINCNTL115
DSIS: PIN
MM: MUX2
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
UART4, GP2
PINCNTL207
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD
MCA[4], GP0
PINCNTL54
DSIS: PIN
MM: MUX0
VOUT[1]_AVID/
EMAC[1]_MRXER/
VIN[1]A_CLK/
UART4_RTS/
TIM6_IO/
GP2[31]
MCA[4]_AXR[1]/
TIM6_IO/
GP0[24]
(1)
(2)
(3)
122
Y22
J4
Timer 6 capture event input or PWM output
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-35. Timer Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
Timer 5
GPMC_ADV_ALE/
GPMC_CS[6]/
TIM5_IO/
GP1[28]
GPMC_A[23]/
SPI[2]_SCLK/
HDMI_HPDET/
TIM5_IO/
GP1[18]
DEVOSC_WAKE/
SPI[1]_SCS[1]/
TIM5_IO/
GP1[7]
MCA[3]_AXR[1]/
TIM5_IO/
GP0[19]
M26
AA26
W6
G2
I/O
IPU
DVDD_GPMC
GPMC, GP1
PINCNTL128
DSIS: PIN
MM: MUX3
I/O
IPD
DVDD_GPMC
GPMC, SPI[2],
HDMI, GP1
PINCNTL112
DSIS: PIN
MM: MUX2
I/O
IPU
DVDD_SD
OSC, SPI[1], GP1
PINCNTL7
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD
MCA[3], GP0
PINCNTL48
DSIS: PIN
MM: MUX0
Timer 5 capture event input or PWM output
Timer 4
GPMC_CLK/
GPMC_CS[5]/
GPMC_WAIT[1]/
CLKOUT1/
EDMA_EVT3/
TIM4_IO/
GP1[27]
GPMC_A[22]/
SPI[2]_D[1]/
HDMI_CEC/
TIM4_IO/
GP1[17]
SPI[0]_SCS[1]/
SD1_SDCD/
SATA_ACT0_LED/
EDMA_EVT1/
TIM4_IO/
GP1[6]
MCA[3]_AXR[0]/
TIM4_IO/
GP0[18]
R26
AB27
AE5
G1
I/O
IPU
DVDD_GPMC
GPMC, CLKOUT1,
EDMA, GP1
PINCNTL127
DSIS: PIN
MM: MUX3
I/O
IPU
DVDD_GPMC
GPMC, SPI[2],
HDMI, GP1
PINCNTL111
DSIS: PIN
MM: MUX2
I/O
IPU
DVDD
SPI[0], SD1,
SATA, EDMA,
GP1
PINCNTL80
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD
MCA[3], GP0
PINCNTL47
DSIS: PIN
MM: MUX0
Timer 4 capture event input or PWM output
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
123
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-35. Timer Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
Timer 3
CLKIN32/
CLKOUT0/
TIM3_IO/
GP3[31]
GPMC_A[19]/
TIM3_IO/
GP1[14]
AUD_CLKIN2/
MCA[0]_AXR[9]/
MCA[2]_AHCLKX/
MCA[5]_AHCLKX/
EDMA_EVT2/
TIM3_IO/
GP0[9]
MCA[2]_AXR[3]/
MCA[1]_AXR[7]/
TIM3_IO/
GP0[15]
J7
AC27
H1
H2
I/O
IPD
DVDD
CLKIN32,
CLKOUT, GP3
PINCNTL259
DSIS: PIN
MM: MUX3
I/O
IPD
DVDD_GPMC
GPMC, GP1
PINCNTL108
DSIS: PIN
MM: MUX2
IPD
DVDD
AUD_CLKIN2,
MCA[0], MCA[2].
MCA[5], EDMA,
GP0
PINCNTL16
DSIS: PIN
MM: MUX1
IPD
DVDD
MCA[2], MCA[1],
GP0
PINCNTL44
DSIS: PIN
MM: MUX0
I/O
I/O
Timer 3 capture event input or PWM output
Timer 2
EMAC_RMREFCLK/
TIM2_IO/
GP1[10]
GPMC_A[18]/
TIM2_IO/
GP0[13]
AUD_CLKIN1/
MCA[0]_AXR[8]/
MCA[1]_AHCLKX/
MCA[4]_AHCLKX/
EDMA_EVT3/
TIM2_IO/
GP0[8]
MCA[2]_AXR[2]/
MCA[1]_AXR[6]/
TIM2_IO/
GP0[14]
J27
I/O
IPD
DVDD_GPMC
EMAC, GP1
PINCNTL232
DSIS: PIN
MM: MUX3
AE28
I/O
IPD
DVDD_GPMC
GPMC, GP0
PINCNTL107
DSIS: PIN
MM: MUX2
I/O
IPD
DVDD
AUD_CLKIN1,
MCA[0], MCA[1],
MCA[4], EDMA,
GP0
PINCNTL15
DSIS: PIN
MM: MUX1
I/O
IPD
DVDD
MCA[2], MCA[1],
GP0
PINCNTL43
DSIS: PIN
MM: MUX0
O
DIS
DVDD
R5
V5
Timer 2 capture event input or PWM output
Watchdog Timer 0
RSTOUT_WD_OUT
124
Device Pins
–
PINCNTL262
Watchdog timer 0 event output
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.20 UART
Table 3-36. UART0 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
UART0
UART0_RXD
AH5
I
IPU
DVDD
–
PINCNTL70
DSIS: PIN
UART0 Receive Data Input. Functions as IrDA receive input
in IrDA modes and CIR receive input in CIR mode.
UART0_TXD
AG5
O
IPU
DVDD
–
PINCNTL71
DSIS: PIN
UART0 Transmit Data Output. Functions as CIR transmit
output in CIR mode.
UART0_RTS/
UART4_TXD/
DCAN1_RX/
SPI[1]_SCS[2]/
SD2_SDCD
AF5
O
IPU
DVDD
UART4, DCAN1,
SPI[1], SD2
PINCNTL73
DSIS: PIN
UART0 Request to Send Output. Indicates module is ready
to receive data. Functions as transmit data output in IrDA
modes.
I/O
IPU
DVDD
UART4, DCAN1,
SPI[1], SD0
PINCNTL72
DSIS: 1
UART0 Clear to Send Input. Functions as SD transceiver
control output in IrDA and CIR modes.
UART3, UART1,
GP1
PINCNTL76
DSIS: PIN
UART0 Data Terminal Ready Output
UART0_CTS/
UART4_RXD/
DCAN1_TX/
SPI[1]_SCS[3]/
SD0_SDCD
AE6
UART0_DTR/
UART3_CTS/
UART1_TXD/
GP1[4]
AG2
O
IPU
DVDD
UART0_DSR/
UART3_TXD/
SPI[0]_SCS[2]/
I2C[2]_SDA/
SD1_SDWP/
GP1[3]
AG4
I
IPU
DVDD
UART3, SPI[0],
I2C[2], SD1, GP1
PINCNTL75
DSIS: 1
UART0 Data Set Ready Input
UART3, SPI[0],
I2C[2], SD1, GP1
PINCNTL74
DSIS: 1
UART0 Data Carrier Detect Input
UART3, UART1,
GP1
PINCNTL77
DSIS: 1
UART0 Ring Indicator Input
UART0_DCD/
UART3_RXD/
SPI[0]_SCS[3]/
I2C[2]_SCL/
SD1_POW/
GP1[2]
AH4
I
IPU
DVDD
UART0_RIN/
UART3_RTS/
UART1_RXD/
GP1[5]
AF4
I
IPU
DVDD
(1)
(2)
(3)
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
125
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-37. UART1 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
UART1
EMAC[0]_MTXD[5]/
EMAC[1]_RGTXC/
EMAC[1]_RMCRSDV/
GPMC_A[12]/
UART1_RXD
UART0_RIN/
UART3_RTS/
UART1_RXD/
GP1[5]
EMAC[0]_MTXD[6]/
EMAC[1]_RGRXD[0]/
EMAC[1]_RMTXD[0]/
GPMC_A[13]/
UART1_TXD
F27
AF4
J22
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], GPMC
PINCNTL255
DSIS: 1
MM: MUX1
I
IPU
DVDD
UART0, UART3,
GP1
PINCNTL77
DSIS: 1
MM: MUX0
O
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], GPMC
PINCNTL256
DSIS: PIN
MM: MUX1
I
UART1 Receive Data Input. Functions as IrDA receive
input in IrDA modes and CIR receive input in CIR mode.
UART1 Transmit Data Output. Functions as CIR transmit
output in CIR mode.
UART0_DTR/
UART3_CTS/
UART1_TXD/
GP1[4]
AG2
O
IPU
DVDD
UART0, UART3,
GP1
PINCNTL76
DSIS: PIN
MM: MUX0
EMAC[0]_MTXEN/
EMAC[1]_RGRXD[2]/
EMAC[1]_RMTXEN/
GPMC_A[15]/
UART1_RTS
J23
O
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], GPMC
PINCNTL258
DSIS: PIN
UART1 Request to Send Output. Indicates module is
ready to receive data. Functions as transmit data output
in IrDA modes.
EMAC[0]_MTXD[7]/
EMAC[1]_RGTXD[3]/
EMAC[1]_RMTXD[1]/
GPMC_A[14]/
UART1_CTS
H24
I/O
IPD
DVDD_GPMC
EMCA[0],
EMAC[1], GPMC
PINCNTL257
DSIS: 1
UART1 Clear to Send Input. Functions as SD
transceiver control output in IrDA and CIR modes.
(1)
(2)
(3)
126
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-38. UART2 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
UART2
SD2_DAT[7]/
GPMC_A[24]/
GPMC_A[20]/
UART2_RXD/
GP1[19]
DCAN0_RX/
UART2_RXD/
I2C[3]_SCL/
GP1[1]
UART2_RXD/
GP0[29]
VOUT[1]_B_CB_C[1]/
CAM_HS/
GPMC_A[9]/
UART2_RXD/
GP0[26]
SD2_DAT[6]/
GPMC_A[25]/
GPMC_A[21]/
UART2_TXD/
GP1[20]
DCAN0_TX/
UART2_TXD/
I2C[3]_SDA/
GP1[0]
UART2_TXD/
GP0[31]
VOUT[1]_B_CB_C[0]/
CAM_VS/
GPMC_A[10]/
UART2_TXD/
GP0[27]
VOUT[0]_FLD/
CAM_PCLK/
GPMC_A[12]/
UART2_RTS/
GP2[2]
VOUT[1]_FLD/
CAM_FLD/
CAM_WE/
GPMC_A[11]/
UART2_CTS/
GP0[28]
(1)
(2)
(3)
L25
AG6
U4
I
IPU
DVDD_GPMC
SD2, GPMC, GP1
PINCNTL113
DSIS: 1
MM: MUX3
I
IPU
DVDD
DCAN0, I2C[3],
GP1
PINCNTL69
DSIS: 1
MM: MUX2
IPD
DVDD
GP0
PINCNTL59
DSIS: 1
MM: MUX1
I
UART2 Receive Data Input. Functions as IrDA receive
input in IrDA modes and CIR receive input in CIR mode.
AE23
I
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, GP0
PINCNTL172
DSIS: 1
MM: MUX0
N23
O
IPU
DVDD_GPMC
SD2, GPMC, GP1
PINCNTL114
DSIS: PIN
MM: MUX3
O
IPU
DVDD
DCAN0, I2C[3],
GP1
PINCNTL68
DSIS: PIN
MM: MUX2
IPD
DVDD
GP0
PINCNTL61
DSIS: PIN
MM: MUX1
O
IPU
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, GP0
PINCNTL173
DSIS: PIN
MM: MUX0
O
IPD
DVDD_C
VOUT[0],
CAMERA_I/F,
GPMC, GP2
PINCNTL175
DSIS: PIN
UART2 Request to Send Output. Indicates module is
ready to receive data. Functions as transmit data output
in IrDA modes.
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, GP0
PINCNTL174
DSIS: 1
UART2 Clear to Send Input. Functions as SD
transceiver control output in IrDA and CIR modes.
AH6
U3
AD23
AF18
AB23
O
I/O
UART2 Transmit Data Output. Functions as CIR
transmit output in CIR mode.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
127
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-39. UART3 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
UART3
VOUT[1]_B_CB_C[6]/
EMAC[1]_MRXD[2]/
VIN[1]A_D[3]/
UART3_RXD/
GP3[3]
AD25
I
IPD
DVDD
UART0_DCD/
UART3_RXD/
SPI[0]_SCS[3]/
I2C[2]_SCL/
SD1_POW/
GP1[2]
AH4
I
IPU
DVDD
VOUT[1]_B_CB_C[7]/
EMAC[1]_MRXD[3]/
VIN[1]A_D[4]/
UART3_TXD/
GP3[4]
AC25
O
IPD
DVDD
UART0_DSR/
UART3_TXD/
SPI[0]_SCS[2]/
I2C[2]_SDA/
SD1_SDWP/
GP1[3]
AG4
O
IPU
DVDD
VOUT[1]_HSYNC/
EMAC[1]_MCOL/
VIN[1]A_VSYNC/
SPI[3]_D[1]/
UART3_RTS/
GP2[29]
UART0_RIN/
UART3_RTS/
UART1_RXD/
GP1[5]
AC24
O
IPD
DVDD
AF4
O
IPU
DVDD
VOUT[1]_VSYNC/
EMAC[1]_MCRS/
VIN[1]A_FLD/
VIN[1]A_DE/
SPI[3]_D[0]/
UART3_CTS/
GP2[30]
AA23
I/O
IPD
DVDD
UART0_DTR/
UART3_CTS/
UART1_TXD/
GP1[4]
AG2
I/O
IPU
DVDD
(1)
(2)
(3)
128
VOUT[1],
EMAC[1], VIN[1]A,
GP3
PINCNTL211
DSIS: 1
MM: MUX1
UART3 Receive Data Input. Functions as IrDA receive input
in IrDA modes and CIR receive input in CIR mode.
UART0, SPI[0],
I2C[2], SD1, GP1
PINCNTL74
DSIS: 1
MM: MUX0
VOUT[1],
EMAC[1], VIN[1]A,
GP3
PINCNTL212
DSIS: PIN
MM: MUX1
UART3 Transmit Data Output. Functions as CIR transmit
output in CIR mode.
UART0, SPI[0],
I2C[2], SD1, GP1
PINCNTL75
DSIS: PIN
MM: MUX0
VOUT[1],
EMAC[1], VIN[1]A,
SPI[3], GP2
PINCNTL205
DSIS: PIN
UART3 Request to Send Output. Indicates module is ready
MM: MUX1
to receive data. Functions as transmit data output in IrDA
UART0, UART1, modes.
GP1
PINCNTL77
DSIS: PIN
MM: MUX0
VOUT[1],
EMAC[1], VIN[1]A,
SPI[3], GP2
PINCNTL206
DSIS: 1
UART3 Clear to Send Input. Functions as SD transceiver
MM: MUX1
control output in IrDA and CIR modes.
UART3, UART1,
GP1
PINCNTL76
DSIS: 1
MM: MUX0
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-40. UART4 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
UART4
UART0_CTS/
UART4_RXD/
DCAN1_TX/
SPI[1]_SCS[3]/
SD0_SDCD
AE6
I
IPU
DVDD
VOUT[1]_B_CB_C[4]/
EMAC[1]_MRXD[0]/
VIN[1]A_D[1]/
UART4_RXD/
GP3[1]
AG25
I
IPD
DVDD
EMAC[0]_MTXD[1]/
EMAC[1]_RGTXD[1]/
GPMC_A[8]/
UART4_RXD
H25
I
IPD
DVDD_GPMC
VOUT[1]_G_Y_YC[1]/
CAM_D[3]/
GPMC_A[5]/
UART4_RXD/
GP0[22]
UART0_RTS/
UART4_TXD/
DCAN1_RX/
SPI[1]_SCS[2]/
SD2_SDCD
AD18
AF5
I
IPU
DVDD_C
O
IPU
DVDD
UART0, DCAN1,
SPI[1], SD2
PINCNTL73
DSIS: PIN
MM: MUX3
AF25
O
IPD
DVDD
EMAC[0]_MTXD[2]/
EMAC[1]_RGTXCTL/
EMAC[1]_RMRXD[0]/
GPMC_A[9]/
UART4_TXD
H22
O
IPD
DVDD_GPMC
(1)
(2)
(3)
AC18
VOUT[1],
EMAC[1], VIN[1]A,
GP3
PINCNTL209
DSIS: 1
MM: MUX2
UART4 Receive Data Input. Functions as IrDA receive
input in IrDA modes and CIR receive input in CIR mode.
EMAC[0],
EMAC[1], GPMC
PINCNTL251
DSIS: 1
MM: MUX1
VOUT[1],
CAMERA_I/F,
GPMC, GP0
PINCNTL168
DSIS: 1
MM: MUX0
VOUT[1]_B_CB_C[5]/
EMAC[1]_MRXD[1]/
VIN[1]A_D[2]/
UART4_TXD/
GP3[2]
VOUT[1]_G_Y_YC[0]/
CAM_D[2]/
GPMC_A[6]/
UART4_TXD/
GP0[23]
UART0, DCAN1,
SPI[1], SD0
PINCNTL72
DSIS: 1
MM: MUX3
O
IPD
DVDD_C
VOUT[1],
EMAC[1], VIN[1]A,
GP3
PINCNTL210
DSIS: PIN
MM: MUX2
UART4 Transmit Data Output. Functions as CIR transmit
output in CIR mode.
EMAC[0],
EMAC[1], GPMC
PINCNTL252
DSIS: PIN
MM: MUX1
VOUT[1],
CAMERA_I/F,
GPMC, GP0
PINCNTL169
DSIS: PIN
MM: MUX0
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
129
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-40. UART4 Terminal Functions (continued)
SIGNAL
NAME
VOUT[1]_AVID/
EMAC[1]_MRXER/
VIN[1]A_CLK/
UART4_RTS/
TIM6_IO/
GP2[31]
EMAC[0]_MTXD[4]/
EMAC[1]_RGTXD[2]/
EMAC[1]_RMRXER/
GPMC_A[11]/
UART4_RTS
VOUT[1]_R_CR[0]/
CAM_D[0]/
GPMC_A[8]/
UART4_RTS/
GP0[25]
VOUT[1]_B_CB_C[3]/
EMAC[1]_MRCLK/
VIN[1]A_D[0]/
UART4_CTS/
GP3[0]
EMAC[0]_MTXD[3]/
EMAC[1]_RGTXD[0]/
EMAC[1]_RMRXD[1]/
GPMC_A[10]/
UART4_CTS
VOUT[1]_R_CR[1]/
CAM_D[1]/
GPMC_A[7]/
UART4_CTS/
GP0[24]
130
Device Pins
NO.
Y22
G23
AA22
AH25
H23
AC19
TYPE (1)
OTHER (2)
(3)
MUXED
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
TIMER6, GP2
PINCNTL207
DSIS: PIN
MM: MUX2
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], GPMC
PINCNTL254
DSIS: PIN
MM: MUX1
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, GP0
PINCNTL171
DSIS: PIN
MM: MUX0
I/O
IPD
DVDD
VOUT[1],
EMAC[1], VIN[1]A,
GP3
PINCNTL208
DSIS: 1
MM: MUX2
I/O
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], GPMC
PINCNTL253
DSIS: 1
MM: MUX1
IPD
DVDD_C
VOUT[1],
CAMERA_I/F,
GPMC, GP0
PINCNTL170
DSIS: 1
MM: MUX0
O
O
O
I/O
DESCRIPTION
UART4 Request to Send Output. Indicates module is
ready to receive data. Functions as transmit data output
in IrDA modes.
UART4 Clear to Send Input. Functions as SD transceiver
control output in IrDA and CIR modes.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-41. UART5 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
UART5
MCA[2]_AXR[0]/
SD0_DAT[6]/
UART5_RXD/
GP0[12]
VOUT[1]_R_CR[8]/
EMAC[1]_MTXD[7]/
VIN[1]A_D[19]/
UART5_RXD/
GP3[18]
VIN[0]A_FLD/
VIN[0]B_VSYNC/
UART5_RXD/
I2C[2]_SCL/
GP2[1]
N2
W23
AA20
IPU
DVDD
MCA[2], SD0, GP0
PINCNTL41
DSIS: 1
MM: MUX3
I
IPD
DVDD
VOUT[1], EMAC[1],
VIN[1]A, GP3
PINCNTL226
DSIS: 1
MM: MUX2
I
IPU
DVDD
VIN[0]A, I2C[2],
GP2
PINCNTL136
DSIS: 1
MM: MUX1
I
EMAC[0]_MRXD[3]/
EMAC[1]_RGRXCTL
/
GPMC_A[27]/
GPMC_A[26]/
GPMC_A[0]/
UART5_RXD
J25
I
IPD
DVDD_GPMC
EMAC[0],
EMAC[1], GPMC
PINCNTL243
DSIS: 1
MM: MUX0
MCA[2]_AXR[1]/
SD0_DAT[7]/
UART5_TXD/
GP0[13]
V6
O
IPU
DVDD
MCA[2], SD0, GP0
PINCNTL42
DSIS: PIN
MM: MUX3
O
IPD
DVDD
VOUT[1], EMAC[1],
VIN[1]A, GP3
PINCNTL227
DSIS: PIN
MM: MUX2
VOUT[1]_R_CR[9]/
EMAC[1]_MTXEN/
VIN[1]A_D[20]/
UART5_TXD/
GP3[19]
VIN[0]A_DE/
VIN[0]B_HSYNC/
UART5_TXD/
I2C[2]_SDA/
GP2[0]
EMAC[0]_MRXD[4]/
EMAC[0]_RGRXD[3]
/
GPMC_A[1]/
UART5_TXD
VIN[0]A_HSYNC/
UART5_RTS/
GP2[3]
EMAC[0]_MRXD[6]/
EMAC[0]_RGTXD[2]
/
GPMC_A[3]/
UART5_RTS
(1)
(2)
(3)
Y24
AE21
O
IPU
DVDD
VIN[0]A, I2C[2],
GP0
PINCNTL135
DSIS: PIN
MM: MUX1
T23
O
IPD
DVDD_GPMC
EMAC[0], GPMC
PINCNTL244
DSIS: PIN
MM: MUX0
AC20
O
IPU
DVDD
VIN[0]A, GP2
PINCNTL138
DSIS: PIN
MM: MUX1
F28
O
IPD
DVDD_GPMC
EMAC[0], GPMC
PINCNTL246
DSIS: PIN
MM: MUX0
UART5 Receive Data Input. Functions as IrDA receive
input in IrDA modes and CIR receive input in CIR mode.
UART5 Transmit Data Output. Functions as CIR transmit
output in CIR mode.
UART5 Request to Send Output. Indicates module is
ready to receive data. Functions as transmit data output in
IrDA modes.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
131
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-41. UART5 Terminal Functions (continued)
SIGNAL
NAME
VIN[0]A_VSYNC/
UART5_CTS/
GP2[4]
EMAC[0]_MRXD[5]/
EMAC[0]_RGTXD[3]
/
GPMC_A[2]/
UART5_CTS
132
Device Pins
NO.
AD20
H26
TYPE (1)
I/O
I/O
OTHER (2)
(3)
MUXED
IPU
DVDD
VIN[0]A, GP2
PINCNTL139
DSIS: 1
MM: MUX1
IPD
DVDD_GPMC
EMAC[0], GPMC
PINCNTL245
DSIS: 1
MM: MUX0
DESCRIPTION
UART5 Clear to Send Input. Functions as SD transceiver
control output in IrDA and CIR modes.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.21 USB
Table 3-42. USB Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
USB0
USB0_DP
AG11
A I/O
–
VDDA_USB_3P3
–
USB0 bidirectional data differential signal pair
[plus/minus].
USB0_DM
AH11
A I/O
–
VDDA_USB_3P3
–
When the USB0 PHY is powered down, these pins
should be left unconnected.
USB0_ID
AG10
AI
–
VDDA_USB_3P3
–
USB0_CE
AH10
AO
–
VDDA_USB_3P3
–
USB0 OTG identification input.
When the USB0 PHY is powered down, this pin should
be left unconnected.
USB0 charger enable.
When the USB0 PHY is powered down, this pin should
be left unconnected.
5-V USB0 VBUS comparator input.
USB0_VBUSIN
USB0_DRVVBUS/
GP0[7]
AG12
AF11
AI
O
–
VDDA_USB_3P3
IPD
DVDD
–
GP0
PINCNTL270
DSIS: N/A
This analog input pin senses the level of the USB VBUS
voltage and should connect directly to the USB VBUS
voltage. When the USB0 PHY is powered down, this pin
should be left unconnected.
When this pin is used as USB0_DRVVBUS and the
USB0 Controller is operating as a Host, this signal is
used by the USB0 Controller to enable the external
VBUS charge pump.
When the USB0 PHY is powered down, this pin should
be left unconnected.
USB1
USB1_DP
AG13
A I/O
–
VDDA_USB_3P3
–
USB1 bidirectional data differential signal pair
[plus/minus].
USB1_DM
AH13
A I/O
–
VDDA_USB_3P3
–
When the USB1 PHY is powered down, these pins
should be left unconnected.
USB1_ID
AH12
AI
–
VDDA_USB_3P3
–
USB1_CE
AH14
AO
–
VDDA_USB_3P3
–
USB1 OTG identification input.
When the USB1 PHY is powered down, this pin should
be left unconnected.
USB1 charger enable.
When the USB1 PHY is powered down, this pin should
be left unconnected.
5-V USB1 VBUS comparator input.
USB1_VBUSIN
AUD_CLKIN0/
MCA[0]_AXR[7]/
MCA[0]_AHCLKX/
MCA[3]_AHCLKX/
USB1_DRVVBUS
(1)
(2)
(3)
AG14
L5
AI
O
–
VDDA_USB_3P3
–
IPD
DVDD
AUD_CLKIN0,
MCA[0], MCA[3],
PINCNTL14
DSIS: N/A
This analog input pin senses the level of the USB VBUS
voltage and should connect directly to the USB VBUS
voltage. When the USB1 PHY is powered down, this pin
should be left unconnected.
When this pin is used as USB1_DRVVBUS and the
USB1 Controller is operating as a Host, this signal is
used by the USB1 Controller to enable the external
VBUS charge pump.
When the USB1 PHY is powered down, this pin should
be left unconnected.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
133
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3.2.22 Video Input (Digital)
Table 3-43. Video Input 0 (Digital) Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
Video Input 0 (Digital)
VIN[0]B_CLK/
CLKOUT0/
GP1[9]
AE17
I
IPD
DVDD
CLKOUT0, GP1
PINCNTL134
DSIS: 0
Video Input 0 Port B Clock input. Input clock for 8-bit
Port B video capture. This signal is not used in 16-bit
and 24-bit capture modes.
VIN[0]A_CLK/
GP2[2]
AB20
I
IPD
DVDD
GP2
PINCNTL137
DSIS: 0
Video Input 0 Port A Clock input. Input clock for 8-bit ,
16-bit, or 24-bit Port A video capture.
I
IPD
DVDD_C
CAM_IF,
EMAC[1]_RM,
SPI[3], GP0
PINCNTL163
DSIS: PIN
I
IPD
DVDD_C
CAM_IF,
EMAC[1]_RM,
SPI[3], GP0
PINCNTL162
DSIS: PIN
I
IPD
DVDD_C
CAM_IF,
EMAC[1]_RM,
SPI[3], GP0
PINCNTL161
DSIS: PIN
I
IPD
DVDD_C
CAM_IF,
EMAC[1]_RM,
SPI[3], GP0
PINCNTL160
DSIS: PIN
I
IPU
DVDD_C
CAM_IF,
EMAC[1]_RM,
I2C[3], GP0
PINCNTL159
DSIS: PIN
I
IPU
DVDD_C
CAM_IF,
EMAC[1]_RM,
I2C[3], GP0
PINCNTL158
DSIS: PIN
CAM_IF,
EMAC[1]_RM,
I2C[3], GP0
PINCNTL157
DSIS: PIN
CAM_IF, I2C[3],
GP0
PINCNTL156
DSIS: PIN
VIN[0]A_D[23]/
CAM_D[15]/
EMAC[1]_RMTXEN/
SPI[3]_D[0]/
GP0[17]
VIN[0]A_D[22]/
CAM_D[14]/
EMAC[1]_RMTXD[1]/
SPI[3]_D[1]/
GP0[16]
VIN[0]A_D[21]/
CAM_D[13]/
EMAC[1]_RMTXD[0]/
SPI[3]_SCLK/
GP0[15]
VIN[0]A_D[20]/
CAM_D[12]/
EMAC[1]_RMCRSDV/
SPI[3]_SCS[0]/
GP0[14]
VIN[0]A_D[19]/
CAM_D[11]/
EMAC[1]_RMRXD[0]/
I2C[3]_SDA/
GP0[13]
VIN[0]A_D[18]/
CAM_D[10]/
EMAC[1]_RMRXD[1]/
I2C[3]_SCL/
GP0[12]
AC16
AC21
AE18
AC17
AF21
AF20
VIN[0]A_D[17]/
CAM_D[9]/
EMAC[1]_RMRXER/
GP0[11]
AB21
I
IPD
DVDD_C
VIN[0]A_D[16]/
CAM_D[8]/
I2C[2]_SCL/
GP0[10]
AA21
I
IPU
DVDD_C
(1)
(2)
(3)
134
Video Input 0 Data inputs. For 16-bit capture, D[7:0] are
Cb/Cr and [15:8] are Y Port A inputs. For 8-bit capture,
D[7:0] are Port A YCbCr data inputs and D[15:8] are Port
B YCbCr data inputs. For RGB capture, D[23:16] are R,
D[15:8] are G, and D[7:0] are B data inputs.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal.
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-43. Video Input 0 (Digital) Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
VIN[0]A_D[15]_BD[7]/
CAM_SHUTTER/
GP2[20]
AC14
I
IPD
DVDD
CAM_IF, GP2
PINCNTL155
DSIS: PIN
VIN[0]A_D[14]_BD[6]/
CAM_STROBE/
GP2[19]
AC12
I
IPD
DVDD
CAM_IF, GP2
PINCNTL154
DSIS: PIN
VIN[0]A_D[13]_BD[5]/
CAM_RESET/
GP2[18]
AF17
I
IPD
DVDD
CAM_IF, GP2
PINCNTL153
DSIS: PIN
VIN[0]A_D[12]_BD[4]/
CLKOUT1/
GP2[17]
AG17
I
IPD
DVDD
CLKOUT1, GP2
PINCNTL152
DSIS: PIN
VIN[0]A_D[11]_BD[3]/
CAM_WE/
GP2[16]
AH17
I
IPD
DVDD
CAM_IF, GP2
PINCNTL151
DSIS: PIN
VIN[0]A_D[10]_BD[2]/
GP2[15]
AH9
I
IPD
DVDD
GP2
PINCNTL150
DSIS: PIN
VIN[0]A_D[9]_BD[1]/
GP2[14]
AG9
I
IPD
DVDD
GP2
PINCNTL149
DSIS: PIN
VIN[0]A_D[8]_BD[0]/
GP2[13]
AB15
I
IPD
DVDD
GP2
PINCNTL148
DSIS: PIN
VIN[0]A_D[7]/
GP2[12]
AA11
I
IPD
DVDD
GP2
PINCNTL147
DSIS: PIN
VIN[0]A_D[6]/
GP2[11]
AH16
I
IPD
DVDD
GP2
PINCNTL146
DSIS: PIN
VIN[0]A_D[5]/
GP2[10]
AG16
I
IPD
DVDD
GP2
PINCNTL145
DSIS: PIN
VIN[0]A_D[4]/
GP2[9]
AH8
I
IPD
DVDD
GP2
PINCNTL144
DSIS: PIN
VIN[0]A_D[3]/
GP2[8]
AE12
I
IPD
DVDD
GP2
PINCNTL143
DSIS: PIN
VIN[0]A_D[2]/
GP2[7]
AC9
I
IPD
DVDD
GP2
PINCNTL142
DSIS: PIN
VIN[0]A_D[1]/
GP1[12]
AB11
I
IPD
DVDD
GP1
PINCNTL141
DSIS: PIN
VIN[0]A_D[0]/
GP1[11]
AF9
I
IPD
DVDD
GP1
PINCNTL140
DSIS: PIN
VIN[0]A_DE/
VIN[0]B_HSYNC/
UART5_TXD/
I2C[2]_SDA/
GP2[0]
AE21
I
IPU
DVDD
VIN[0]A, UART5,
I2C[2], GP2
PINCNTL135
DSIS: 0
Video Input 0 Port B Horizontal Sync input. Discrete
horizontal synchronization signal for Port B 8-bit YCbCr
capture without embedded syncs (“BT.601” modes). Not
used in RGB or 16-bit YCbCr capture modes
VIN[0]A_HSYNC/
UART5_RTS/
GP2[3]
AC20
I
IPU
DVDD
UART5, GP2
PINCNTL138
DSIS: 0
Video Input 0 Port A Horizontal Sync0 input. Discrete
horizontal synchronization signal for Port A RGB capture
mode or YCbCr capture without embedded syncs
(“BT.601” modes).
Video Input 0 Data inputs. For 16-bit capture, D[7:0] are
Cb/Cr and [15:8] are Y Port A inputs. For 8-bit capture,
D[7:0] are Port A YCbCr data inputs and D[15:8] are Port
B YCbCr data inputs. For RGB capture, D[23:16] are R,
D[15:8] are G, and D[7:0] are B data inputs.
Video Input 0 Data inputs. For 16-bit capture, D[7:0] are
Cb/Cr and [15:8] are Y Port A inputs. For 8-bit capture,
D[7:0] are Port A YCbCr data inputs and D[15:8] are Port
B YCbCr data inputs. For RGB capture, D[23:16] are R,
D[15:8] are G, and D[7:0] are B data inputs.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
135
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-43. Video Input 0 (Digital) Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
Video Input 0 Port B Vertical Sync1 input. Discrete
vertical synchronization signal for Port B 8-bit YCbCr
capture without embedded syncs (“BT.601” modes). Not
used in RGB or 16-bit YCbCr capture modes.
VIN[0]A_FLD/
VIN[0]B_VSYNC/
UART5_RXD/
I2C[2]_SCL/
GP2[1]
AA20
I
IPU
DVDD
VIN[0]A, UART5,
I2C[2], GP2
PINCNTL136
DSIS:0
VIN[0]A_VSYNC/
UART5_CTS/
GP2[4]
AD20
I
IPU
DVDD
UART5, GP2
PINCNTL139
DSIS: 0
Video Input 0 Port A Vertical Sync0 input. Discrete
vertical synchronization signal for Port A RGB capture
mode or YCbCr capture without embedded syncs
(“BT.601” modes).
VIN[0]B_FLD/
CAM_D[4]/
GP0[21]
AD17
I
IPU
DVDD_C
CAMERA_I/F,
GP0
PINCNTL167
DSIS: 0
Video Input 0 Port B Field ID input. Discrete field
identification signal for Port B 8-bit YCbCr capture
without embedded syncs (“BT.601” modes). Not used in
RGB or 16-bit YCbCr capture modes.
IPU
DVDD_C
CAMERA_I/F,
GP0
PINCNTL166
DSIS: 0
MM: MUX1
VIN[0]A_FLD/
CAM_D[5]/
GP0[20]
AC22
VIN[0]A_FLD/
VIN[0]B_VSYNC/
UART5_RXD/
I2C[2]_SCL/
GP2[1]
AA20
I
IPU
DVDD
VIN[0]B_DE/
CAM_D[6]/
GP0[19]
AC15
I
IPU
DVDD_C
CAMERA_I/F,
GP0
PINCNTL165
DSIS: 0
I
IPU
DVDD_C
CAMERA_I/F,
GP0
PINCNTL164
DSIS: 0
MM: MUX1
VIN[0]A_DE/
CAM_D[7]/
GP0[18]
AB17
VIN[0]A_DE/
VIN[0]B_HSYNC/
UART5_TXD/
I2C[2]_SDA/
GP2[0]
AE21
136
Device Pins
I
I
IPU
DVDD
Video Input 0 Port A Field ID input. Discrete field
identification signal for Port A RGB capture mode or
VIN[0]B, UART5, YCbCr capture without embedded syncs (“BT.601”
modes).
I2C[2], GP2
PINCNTL136
DSIS: 0
MM: MUX0
Video Input 0 Port B Data Enable input. Discrete data
valid signal for Port B RGB capture mode or YCbCr
capture without embedded syncs (“BT.601” modes).
Video Input 0 Port A Data Enable input. Discrete data
valid signal for Port A RGB capture mode or YCbCr
VIN[0]B, UART5, capture without embedded syncs ("BT.601" modes).
I2C[2], GP2
PINCNTL135
DSIS: 0
MM: MUX0
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-44. Video Input 1 (Digital) Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
Video Input 1 (Digital)
GPMC_CS[3]/
VIN[1]B_CLK/
SPI[2]_SCS[0]/
GP1[26]
VOUT[1]_AVID/
EMAC[1]_MRXER/
VIN[1]A_CLK/
UART4_RTS/
TIM6_IO/
GP2[31]
VOUT[1]_R_CR[2]/
GPMC_A[15]/
VIN[1]A_D[23]/
HDMI_HPDET/
SPI[2]_D[1]/
GP3[22]
P26
Y22
AE27
IPU
DVDD_GPMC
GPMC, SPI[2],
GP1
PINCNTL125
DSIS: 0
Video Input 1 Port B Clock input. Input clock for 8-bit
Port B video capture. Input data is sampled on the CLK1
edge. This signal is not used in 16-bit and 24-bit capture
modes.
IPD
DVDD
VOUT[1],
EMAC[1],
UART4, TIMER
6, GP2
PINCNTL207
DSIS: 0
Video Input 1 Port A Clock input. Input clock for 8-bit ,
16-bit, or 24-bit Port A video capture. Input data is
sampled on the CLK0 edge.
I
IPD
DVDD
VOUT[1], GPMC,
HDMI, SPI[2],
GP3
PINCNTL230
DSIS: PIN
I
I
VOUT[1]_R_CR[3]/
GPMC_A[14]/
VIN[1]A_D[22]/
HDMI_SDA/
SPI[2]_SCLK/
I2C[2]_SDA/
GP3[21]
AG28
I
IPU
DVDD
VOUT[1]_G_Y_YC[2]/
GPMC_A[13]/
VIN[1]A_D[21]/
HDMI_SCL/
SPI[2]_SCS[2]/
I2C[2]_SCL/
GP3[20]
AF27
I
IPU
DVDD
VOUT[1]_R_CR[9]/
EMAC[1]_MTXEN/
VIN[1]A_D[20]/
UART5_TXD/
GP3[19]
VOUT[1]_R_CR[8]/
EMAC[1]_MTXD[7]/
VIN[1]A_D[19]/
UART5_RXD/
GP3[18]
Y24
W23
IPD
DVDD
VOUT[1],
EMAC[1],
UART5, GP3
PINCNTL227
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1],
UART5, GP3
PINCNTL226
DSIS: PIN
I
VOUT[1]_R_CR[7]/
EMAC[1]_MTXD[6]/
VIN[1]A_D[18]/
SPI[3]_D[0]/
GP3[17]
V22
I
IPD
DVDD
VOUT[1]_R_CR[6]/
EMAC[1]_MTXD[5]/
VIN[1]A_D[17]/
SPI[3]_D[1]/
GP3[16]
AA25
I
IPD
DVDD
VOUT[1]_R_CR[5]/
EMAC[1]_MTXD[4]/
VIN[1]A_D[16]/
SPI[3]_SCLK/
GP3[15]
(1)
(2)
(3)
AC26
VOUT[1], GPMC,
HDMI, SPI[2],
I2C[2], GP3
PINCNTL229
Video Input 1 Data inputs. For 16-bit capture, D[7:0] are
DSIS: PIN
Cb/Cr and [15:8] are Y Port A inputs. For 8-bit capture,
D[7:0] are Port A YCbCr data inputs. For RGB capture,
D[23:16] are R, D[15:8] are G, and D[7:0] are B Port A
VOUT[1], GPMC, data inputs.
HDMI, SPI[2],
I2C[2], GP3
PINCNTL228
DSIS: PIN
IPD
DVDD
I
VOUT[1],
EMAC[1], SPI[3],
GP3
Video Input 1 Data inputs. For 16-bit capture, D[7:0] are
PINCNTL225
Cb/Cr and [15:8] are Y Port A inputs. For 8-bit capture,
DSIS: PIN
D[7:0] are Port A YCbCr data inputs. For RGB capture,
VOUT[1],
D[23:16] are R, D[15:8] are G, and D[7:0] are B Port A
EMAC[1], SPI[3], data inputs.
GP3
PINCNTL224
DSIS: PIN
VOUT[1],
EMAC[1], SPI[3],
GP3
PINCNTL223
DSIS: PIN
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
137
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-44. Video Input 1 (Digital) Terminal Functions (continued)
SIGNAL
NAME
NO.
VOUT[1]_R_CR[4]/
EMAC[1]_MTXD[3]/
VIN[1]A_D[15]/
SPI[3]_SCS[1]/
GP3[14]
AG27
VOUT[1]_G_Y_YC[9]/
EMAC[1]_MTXD[2]/
VIN[1]A_D[14]/
GP3[13]
VOUT[1]_G_Y_YC[8]/
EMAC[1]_MTXD[1]/
VIN[1]A_D[13]/
GP3[12]
VOUT[1]_G_Y_YC[7]/
EMAC[1]_MTXD[0]/
VIN[1]A_D[12]/
GP3[11]
VOUT[1]_G_Y_YC[6]/
EMAC[1]_GMTCLK/
VIN[1]A_D[11]/
GP3[10]
VOUT[1]_G_Y_YC[5]/
EMAC[1]_MRXDV/
VIN[1]A_D[10]/
GP3[9]
VOUT[1]_G_Y_YC[4]/
EMAC[1]_MRXD[7]/
VIN[1]A_D[9]/
GP3[8]
VOUT[1]_G_Y_YC[3]/
EMAC[1]_MRXD[6]/
VIN[1]A_D[8]/
GP3[7]
138
Device Pins
TYPE (1)
OTHER (2)
(3)
MUXED
I
IPD
DVDD
VOUT[1],
EMAC[1], SPI[3],
GP3
PINCNTL222
DSIS: PIN
AD26
I
IPD
DVDD
VOUT[1],
EMAC[1], GP3
PINCNTL221
DSIS: PIN
AE26
I
IPD
DVDD
VOUT[1],
EMAC[1], GP3
PINCNTL220
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1], GP3
PINCNTL219
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1], GP3
PINCNTL218
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1], GP3
PINCNTL217
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1], GP3
PINCNTL216
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1], GP3
PINCNTL215
DSIS: PIN
AF26
AH27
AG26
W22
Y23
DESCRIPTION
Video Input 1 Data inputs. For 16-bit capture, D[7:0] are
Cb/Cr and [15:8] are Y Port A inputs. For 8-bit capture,
D[7:0] are Port A YCbCr data inputs. For RGB capture,
D[23:16] are R, D[15:8] are G, and D[7:0] are B Port A
data inputs.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-44. Video Input 1 (Digital) Terminal Functions (continued)
SIGNAL
NAME
VOUT[1]_B_CB_C[2]/
GPMC_A[0]/
VIN[1]A_D[7]/
HDMI_CEC/
SPI[2]_D[0]/
GP3[30]
VOUT[1]_B_CB_C[9]/
EMAC[1]_MRXD[5]/
VIN[1]A_D[6]/
I2C[3]_SDA/
GP3[6]
VOUT[1]_B_CB_C[8]/
EMAC[1]_MRXD[4]/
VIN[1]A_D[5]/
I2C[3]_SCL/
GP3[5]
VOUT[1]_B_CB_C[7]/
EMAC[1]_MRXD[3]/
VIN[1]A_D[4]/
UART3_TXD/
GP3[4]
VOUT[1]_B_CB_C[6]/
EMAC[1]_MRXD[2]/
VIN[1]A_D[3]/
UART3_RXD/
GP3[3]
VOUT[1]_B_CB_C[5]/
EMAC[1]_MRXD[1]/
VIN[1]A_D[2]/
UART4_TXD/
GP3[2]
VOUT[1]_B_CB_C[4]/
EMAC[1]_MRXD[0]/
VIN[1]A_D[1]/
UART4_RXD/
GP3[1]
NO.
AF28
AA24
AH26
AC25
AD25
AF25
AG25
TYPE (1)
OTHER (2)
(3)
MUXED
IPU
DVDD
VOUT[1], GPMC,
HDMI, SPI[2],
GP3
PINCNTL231
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1], I2C[3],
GP3
PINCNTL214
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1], I2C[3],
GP3
PINCNTL213
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1],
UART3, GP3
PINCNTL212
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1],
UART3, GP3
PINCNTL211
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1],
UART4, GP3
PINCNTL210
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1],
UART4, GP3
PINCNTL209
DSIS: PIN
VOUT[1],
EMAC[1],
UART4, GP3
PINCNTL208
DSIS: PIN
I
VOUT[1]_B_CB_C[3]/
EMAC[1]_MRCLK/
VIN[1]A_D[0]/
UART4_CTS/
GP3[0]
AH25
I
IPD
DVDD
EMAC[0]_MRXD[2]/
EMAC[0]_RGRXD[1]/
VIN[1]B_D[7]/
EMAC[0]_RMTXEN/
GP3[30]
R23
I
IPD
DVDD_GPMC
EMAC[0], GP3
PINCNTL242
DSIS: PIN
EMAC[0]_MRXD[1]/
EMAC[0]_RGRXD[0]/
VIN[1]B_D[6]/
EMAC[0]_RMTXD[1]/
GP3[29]
P23
I
IPD
DVDD_GPMC
EMAC[0], GP3
PINCNTL241
DSIS: PIN
EMAC[0]_MRXD[0]/
EMAC[0]_RGTXD[0]/
VIN[1]B_D[5]/
EMAC[0]_RMTXD[0]/
GP3[28]
G28
I
IPD
DVDD_GPMC
EMAC[0], GP3
PINCNTL240
DSIS: PIN
EMAC[0]_MRCLK/
EMAC[0]_RGTXC/
VIN[1]B_D[4]/
EMAC[0]_RMCRSDV/
SPI[3]_SCS[2]/
GP3[27]
H27
I
IPD
DVDD_GPMC
EMAC[0], SPI[3],
GP3
PINCNTL239
DSIS: PIN
DESCRIPTION
Video Input 1 Data inputs. For 16-bit capture, D[7:0] are
Cb/Cr and [15:8] are Y Port A inputs. For 8-bit capture,
D[7:0] are Port A YCbCr data inputs. For RGB capture,
D[23:16] are R, D[15:8] are G, and D[7:0] are B Port A
data inputs.
Video Input 1 Port B Data inputs. For 8-bit capture,
B_D[7:0] are Port B YCbCr data inputs.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
139
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-44. Video Input 1 (Digital) Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
EMAC[0]_MRXER/
EMAC[0]_RGTXCTL/
VIN[1]B_D[3]/
EMAC[0]_RMRXER/
GP3[26]
J26
I
IPD
DVDD_GPMC
EMAC[0], GP3
PINCNTL238
DSIS: PIN
EMAC[0]_MCRS/
EMAC[0]_RGRXD[2]/
VIN[1]B_D[2]/
EMAC[0]_RMRXD[1]/
GP3[25]
R25
I
IPD
DVDD_GPMC
EMAC[0], GP3
PINCNTL237
DSIS: PIN
EMAC[0]_MCOL/
EMAC[0]_RGRXCTL/
VIN[1]B_D[1]/
EMAC[0]_RMRXD[0]/
GP3[24]
L23
I
IPD
DVDD_GPMC
EMAC[0], GP3
PINCNTL236
DSIS: PIN
EMAC[0]_MTCLK/
EMAC[0]_RGRXC/
VIN[1]B_D[0]/
SPI[3]_SCS[3]/
I2C[2]_SDA/
GP3[23]
L24
I
IPD
DVDD_GPMC
EMAC[0], SPI[3],
I2C[2], GP3
PINCNTL235
DSIS: PIN
I
IPD
DVDD
VOUT[1],
EMAC[1], GP2
PINCNTL204
DSIS: 0
VOUT[1]_CLK/
EMAC[1]_MTCLK/
VIN[1]A_HSYNC/
GP2[28]
VOUT[1]_HSYNC/
EMAC[1]_MCOL/
VIN[1]A_VSYNC/
SPI[3]_D[1]/
UART3_RTS/
GP2[29]
VOUT[1]_VSYNC/
EMAC[1]_MCRS/
VIN[1]A_FLD/
VIN[1]A_DE/
SPI[3]_D[0]/
UART3_CTS/
GP2[30]
VOUT[1]_VSYNC/
EMAC[1]_MCRS/
VIN[1]A_FLD/
VIN[1]A_DE/
SPI[3]_D[0]/
UART3_CTS/
GP2[30]
140
Device Pins
AE24
AC24
AA23
AA23
I
I
I
DESCRIPTION
Video Input Port B Data inputs. For 8-bit capture,
B_D[7:0] are Port B YCbCr data inputs.
Video Input 1 Port A Horizontal Sync input. Discrete
horizontal synchronization signal forPort A YCbCr
capture modes without embedded syncs (“BT.601”
modes).
IPD
DVDD
VOUT[1],
EMAC[1], SPI[3], Video Input 1 Port A Vertical Sync input. Discrete vertical
UART3, GP2
synchronization signal for Port A YCbCr capture modes
PINCNTL205
without embedded syncs (“BT.601” modes).
DSIS: 0
IPD
DVDD
VOUT[1],
EMAC[1],
VIN[1]A, SPI[3],
UART3, GP2
PINCNTL206
DSIS: 0
Video Input 1 Port A Data Enable input. Discrete data
valid signal for Port A YCbCr capture modes without
embedded syncs (“BT.601” modes).
IPD
DVDD
VOUT[1],
EMAC[1],
VIN[1]A, SPI[3],
UART3, GP2
PINCNTL206
DSIS: 0
Video Input 1 Port A Field ID input. Discrete field
identification signal for Port A YCbCr capture modes
without embedded syncs (“BT.601” modes).
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.23 Video Output (Digital)
Table 3-45. Video Output 0 (Digital) Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
Video Output 0
VOUT[0]_CLK
AD12
O
IPD
DVDD
VOUT[0]_G_Y_YC[9]
AF14
O
IPD
DVDD
–
PINCNTL195
VOUT[0]_G_Y_YC[8]
AE14
O
IPD
DVDD
–
PINCNTL194
VOUT[0]_G_Y_YC[7]
AD14
O
IPD
DVDD
–
PINCNTL193
VOUT[0]_G_Y_YC[6]
AA8
O
IPD
DVDD
–
PINCNTL192
VOUT[0]_G_Y_YC[5]
AB12
O
IPD
DVDD
–
PINCNTL191
VOUT[0]_G_Y_YC[4]
AB8
O
IPD
DVDD
–
PINCNTL190
VOUT[0]_G_Y_YC[3]/
GP2[25]
AH15
O
IPD
DVDD
GP2
PINCNTL189
DSIS: PIN
VOUT[0]_G_Y_YC[2]/
EMU3/
GP2[24]
AH7
O
IPD
DVDD
EMU, GP2
PINCNTL188
DSIS: PIN
VOUT[0]_B_CB_C[9]
AG15
O
IPD
DVDD
–
PINCNTL187
VOUT[0]_B_CB_C[8]
AF15
O
IPD
DVDD
–
PINCNTL186
VOUT[0]_B_CB_C[7]
AB10
O
IPD
DVDD
–
PINCNTL185
VOUT[0]_B_CB_C[6]
AC10
O
IPD
DVDD
–
PINCNTL184
VOUT[0]_B_CB_C[5]
AD15
O
IPD
DVDD
–
PINCNTL183
VOUT[0]_B_CB_C[4]
AD11
O
IPD
DVDD
–
PINCNTL182
VOUT[0]_B_CB_C[3]/
GP2[23]
AE15
O
IPD
DVDD
GP2
PINCNTL181
DSIS: PIN
VOUT[0]_B_CB_C[2]/
EMU2/
GP2[22]
AG7
O
IPD
DVDD
EMU2, GP2
PINCNTL180
DSIS: PIN
(1)
(2)
(3)
–
PINCNTL176
Video Output Clock output.
Video Output Data. These signals represent the 8 MSBs
of G/Y/YC video data. For RGB mode they are green
data bits, for YUV444 mode they are Y data bits, for Y/C
mode they are Y (Luma) data bits and for BT.656 mode
they are multiplexed Y/Cb/Cr (Luma and Chroma) data
bits.
Video Output Data. These signals represent the 8 MSBs
of B/CB/C video data. For RGB mode they are blue data
bits, for YUV444 mode they are Cb (Chroma) data bits,
for Y/C mode they are multiplexed Cb/Cr (Chroma) data
bits and for BT.656 mode they are unused.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
141
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-45. Video Output 0 (Digital) Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
VOUT[0]_R_CR[9]/
AC13
O
IPD
DVDD
–
PINCNTL203
VOUT[0]_R_CR[8]/
AE8
O
IPD
DVDD
–
PINCNTL202
VOUT[0]_R_CR[7]/
AF12
O
IPD
DVDD
–
PINCNTL201
VOUT[0]_R_CR[6]/
AF6
O
IPD
DVDD
–
PINCNTL200
–
PINCNTL199
DESCRIPTION
Video Output Data. These signals represent the 8 MSBs
of R/CR video data. For RGB mode they are red data
bits, for YUV444 mode they are Cr (Chroma) data bits,
for Y/C mode and BT.656 modes they are unused.
VOUT[0]_R_CR[5]/
AF8
O
IPD
DVDD
VOUT[0]_R_CR[4]/
AA9
O
IPD
DVDD
–
PINCNTL198
VOUT[0]_R_CR[3]/
GP2[27]
AB9
O
IPD
DVDD
GP2
PINCNTL197
DSIS: PIN
VOUT[0]_R_CR[2]/
EMU4/
GP2[26]
AD9
O
IPD
DVDD
EMU4, GP2
PINCNTL196
DSIS: PIN
VOUT[0]_VSYNC
AB13
O
IPD
DVDD
–
PINCNTL178
Video Output Vertical Sync output. This is the discrete
vertical synchronization output. This signal is not used
for embedded sync modes.
VOUT[0]_HSYNC
AC11
O
IPD
DVDD
–
PINCNTL177
Video Output Horizontal Sync output. This is the discrete
horizontal synchronization output. This signal is not used
for embedded sync modes.
IPD
DVDD_C
CAMERA_I/F,
GPMC, UART2,
GP2
PINCNTL175
DSIS: N/A
MM: MUX1
VOUT[0]_FLD/
CAM_PCLK/
GPMC_A[12]/
UART2_RTS/
GP2[2]
VOUT[0]_AVID/
VOUT[0]_FLD/
SPI[3]_SCLK/
TIM7_IO/
GP2[21]
VOUT[0]_AVID/
VOUT[0]_FLD/
SPI[3]_SCLK/
TIM7_IO/
GP2[21]
142
Device Pins
AF18
AA10
AA10
O
O
IPD
DVDD
VOUT[0], SPI[3],
TIMER7, GP2
PINCNTL179
DSIS: N/A
MM: MUX0
O
IPD
DVDD
VOUT[0], SPI[3],
TIMER7, GP2
PINCNTL179
DSIS: N/A
Video Output Field ID output. This is the discrete field
identification output. This signal is not used for
embedded sync modes.
Video Output Active Video output. This is the discrete
active video indicator output. This signal is not used for
embedded sync modes.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-46. Video Output 1 Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
Video Output 1
VOUT[1]_CLK/
EMAC[1]_MTCLK/
VIN[1]A_HSYNC/
GP2[28]
AE24
O
IPD
DVDD
EMAC[1],
VIN[1]A, GP2
PINCNTL204
DSIS: N/A
EMAC[1],
VIN[1]A, GP3
PINCNTL221
DSIS: N/A
VOUT[1]_G_Y_YC[9]/
EMAC[1]_MTXD[2]/
VIN[1]A_D[14]/
GP3[13]
AD26
O
IPD
DVDD
VOUT[1]_G_Y_YC[8]/
EMAC[1]_MTXD[1]/
VIN[1]A_D[13]/
GP3[12]
AE26
O
IPD
DVDD
EMAC[1],
VIN[1]A, GP3
PINCNTL220
DSIS: N/A
VOUT[1]_G_Y_YC[7]/
EMAC[1]_MTXD[0]/
VIN[1]A_D[12]/
GP3[11]
AF26
O
IPD
DVDD
EMAC[1],
VIN[1]A, GP3
PINCNTL219
DSIS: N/A
VOUT[1]_G_Y_YC[6]/
EMAC[1]_GMTCLK/
VIN[1]A_D[11]/
GP3[10]
AH27
O
IPD
DVDD
EMAC[1],
VIN[1]A, GP3
PINCNTL218
DSIS: N/A
VOUT[1]_G_Y_YC[5]/
EMAC[1]_MRXDV/
VIN[1]A_D[10]/
GP3[9]
AG26
O
IPD
DVDD
EMAC[1],
VIN[1]A, GP3
PINCNTL217
DSIS: N/A
VOUT[1]_G_Y_YC[4]/
EMAC[1]_MRXD[7]/
VIN[1]A_D[9]/
GP3[8]
W22
O
IPD
DVDD
EMAC[1],
VIN[1]A, GP3
PINCNTL216
DSIS: N/A
VOUT[1]_G_Y_YC[3]
EMAC[1]_MRXD[6]/
VIN[1]A_D[8]/
GP3[7]
Y23
O
IPD
DVDD
EMAC[1],
VIN[1]A, GP3
PINCNTL215
DSIS: N/A
O
IPU
DVDD
GPMC, VIN[1]A,
HDMI, SPI[2],
I2C[2], GP3
PINCNTL228
DSIS: N/A
O
IPU
DVDD_C
CAMERA_I/F,
GPMC, UART4,
GP0
PINCNTL168
DSIS: N/A
O
IPD
DVDD_C
CAMERA_I/F,
GPMC, UART4,
GP0
PINCNTL169
DSIS: N/A
VOUT[1]_G_Y_YC[2]/
GPMC_A[13]/
VIN[1]A_D[21]/
HDMI_SCL/
SPI[2]_SCS[2]/
I2C[2]_SCL/
GP3[20]
VOUT[1]_G_Y_YC[1]/
CAM_D[3]/
GPMC_A[5]/
UART4_RXD/
GP0[22]
VOUT[1]_G_Y_YC[0]/
CAM_D[2]/
GPMC_A[6]/
UART4_TXD/
GP0[23]
(1)
(2)
(3)
AF27
AD18
AC18
Video Output Clock output
Video Output Data. These signals represent the 8 MSBs
of G/Y/YC video data. For RGB mode they are green
data bits, for YUV444 mode they are Y data bits, for Y/C
mode they are Y (Luma) data bits and for BT.656 mode
they are multiplexed Y/Cb/Cr (Luma and Chroma) data
bits.
Video Output Data. These signals represent the 8 MSBs
of G/Y/YC video data. For RGB mode they are green
data bits, for YUV444 mode they are Y data bits, for Y/C
mode they are Y (Luma) data bits and for BT.656 mode
they are multiplexed Y/Cb/Cr (Luma and Chroma) data
bits.
Video Output Data. These signals represent the 2 LSBs
of G/Y/YC video data for 10-bit, 20-bit, and 30-bit video
modes (VOUT[1] only). For RGB mode they are green
data bits, for YUV444 mode they are Y data bits, for Y/C
mode they are Y (Luma) data bits and for BT-656 mode
they are multiplexed Y/Cb/Cr (Luma and Chroma) data
bits. These signals are not used in 8/16/24-bit modes.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
143
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-46. Video Output 1 Terminal Functions (continued)
SIGNAL
NAME
VOUT[1]_B_CB_C[9]/
EMAC[1]_MRXD[5]/
VIN[1]A_D[6]/
I2C[3]_SDA/
GP3[6]
VOUT[1]_B_CB_C[8]/
EMAC[1]_MRXD[4]/
VIN[1]A_D[5]/
I2C[3]_SCL/
GP3[5]
VOUT[1]_B_CB_C[7]/
EMAC[1]_MRXD[3]/
VIN[1]A_D[4]/
UART3_TXD/
GP3[4]
VOUT[1]_B_CB_C[6]/
EMAC[1]_MRXD[2]/
VIN[1]A_D[3]/
UART3_RXD/
GP3[3]
VOUT[1]_B_CB_C[5]/
EMAC[1]_MRXD[1]/
VIN[1]A_D[2]/
UART4_TXD/
GP3[2]
VOUT[1]_B_CB_C[4]/
EMAC[1]_MRXD[0]/
VIN[1]A_D[1]/
UART4_RXD/
GP3[1]
VOUT[1]_B_CB_C[3]/
EMAC[1]_MRCLK/
VIN[1]A_D[0]/
UART4_CTS/
GP3[0]
VOUT[1]_B_CB_C[2]/
GPMC_A[0]/
VIN[1]A_D[7]/
HDMI_CEC/
SPI[2]_D[0]/
GP3[30]
VOUT[1]_B_CB_C[1]/
CAM_HS/
GPMC_A[9]/
UART2_RXD/
GP0[26]
VOUT[1]_B_CB_C[0]/
CAM_VS/
GPMC_A[10]/
UART2_TXD/
GP0[27]
144
Device Pins
NO.
AA24
AH26
AC25
AD25
AF25
AG25
AH25
AF28
AE23
AD23
TYPE (1)
OTHER (2)
(3)
MUXED
O
IPD
DVDD
EMAC[1],
VIN[1]A, I2C[3],
GP3
PINCNTL214
DSIS: N/A
O
IPD
DVDD
EMAC[1],
VIN[1]A, I2C[3],
GP3
PINCNTL213
DSIS: N/A
O
IPD
DVDD
EMAC[1],
VIN[1]A, UART3,
GP3
PINCNTL212
DSIS: N/A
O
IPD
DVDD
EMAC[1],
VIN[1]A, UART3,
GP3
PINCNTL211
DSIS: N/A
O
IPD
DVDD
EMAC[1],
VIN[1]A, UART4,
GP3
PINCNTL210
DSIS: N/A
IPD
DVDD
EMAC[1],
VIN[1]A, UART4,
GP3
PINCNTL209
DSIS: N/A
O
IPD
DVDD
EMAC[1],
VIN[1]A, UART4,
GP3
PINCNTL208
DSIS: N/A
O
IPU
DVDD
GPMC, VIN[1]A,
HDMI, SPI[2],
GP3
PINCNTL231
DSIS: N/A
O
IPD
DVDD_C
CAMERA_I/F,
GPMC, UART2,
GP0
PINCNTL172
DSIS: N/A
O
IPU
DVDD_C
CAMERA_I/F,
GPMC, UART2,
GP0
PINCNTL173
DSIS: N/A
O
DESCRIPTION
Video Output Data. These signals represent the 8 MSBs
of B/CB/C video data. For RGB mode they are blue data
bits, for YUV444 mode they are Cb (Chroma) data bits,
for Y/C mode they are multiplexed Cb/Cr (Luma) data
bits, and for BT.656 mode they are not used.
Video Output Data. These signals represent the 8 MSBs
of B/CB/C video data. For RGB mode they are blue data
bits, for YUV444 mode they are Cb (Chroma) data bits,
for Y/C mode they are multiplexed Cb/Cr (Luma) data
bits, and for BT.656 mode they are not used.
Video Output Data. These signals represent the 2 LSBs
of B/CB/C video data for 20-bit, and 30-bit video modes.
For RGB mode they are blue data bits, for YUV444 mode
they are Cb (Chroma) data bits, for Y/C mode they are
multiplexed Cb/Cr (Chroma) data bits and for BT.656
mode they are unused. These signals are not used in
16/24-bit modes.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-46. Video Output 1 Terminal Functions (continued)
SIGNAL
NAME
VOUT[1]_R_CR[9]/
EMAC[1]_MTXEN/
VIN[1]A_D[20]/
UART5_TXD/
GP3[19]
VOUT[1]_R_CR[8]/
EMAC[1]_MTXD[7]/
VIN[1]A_D[19]/
UART5_RXD/
GP3[18]
VOUT[1]_R_CR[7]/
EMAC[1]_MTXD[6]/
VIN[1]A_D[18]/
SPI[3]_D[0]/
GP3[17]
VOUT[1]_R_CR[6]/
EMAC[1]_MTXD[5]/
VIN[1]A_D[17]/
SPI[3]_D[1]/
GP3[16]
VOUT[1]_R_CR[5]/
EMAC[1]_MTXD[4]/
VIN[1]A_D[16]/
SPI[3]_SCLK/
GP3[15]
VOUT[1]_R_CR[4]/
EMAC[1]_MTXD[3]/
VIN[1]A_D[15]/
SPI[3]_SCS[1]/
GP3[14]
VOUT[1]_R_CR[3]/
GPMC_A[14]/
VIN[1]A_D[22]/
HDMI_SDA/
SPI[2]_SCLK/
I2C[2]_SDA/
GP3[21]
VOUT[1]_R_CR[2]/
GPMC_A[15]/
VIN[1]A_D[23]/
HDMI_HPDET/
SPI[2]_D[1]/
GP3[22]
VOUT[1]_R_CR[1]/
CAM_D[1]/
GPMC_A[7]/
UART4_CTS/
GP0[24]
VOUT[1]_R_CR[0]/
CAM_D[0]/
GPMC_A[8]/
UART4_RTS/
GP0[25]
VOUT[1]_VSYNC/
EMAC[1]_MCRS/
VIN[1]A_FLD/
VIN[1]A_DE/
SPI[3]_D[0]/
UART3_CTS/
GP2[30]
NO.
Y24
W23
V22
AA25
AC26
AG27
AG28
AE27
AC19
AA22
AA23
TYPE (1)
OTHER (2)
(3)
MUXED
O
IPD
DVDD
EMAC[1],
VIN[1]A, UART5,
GP3
PINCNTL227
DSIS: N/A
O
IPD
DVDD
EMAC[1],
VIN[1]A, UART5,
GP3
PINCNTL226
DSIS: N/A
O
IPD
DVDD
EMAC[1],
VIN[1]A, SPI[3],
GP3
PINCNTL225
DSIS: N/A
O
IPD
DVDD
EMAC[1],
VIN[1]A, SPI[3],
GP3
PINCNTL224
DSIS: N/A
O
IPD
DVDD
EMAC[1],
VIN[1]A, SPI[3],
GP3
PINCNTL223
DSIS: N/A
IPD
DVDD
EMAC[1],
VIN[1]A, SPI[3],
GP3
PINCNTL222
DSIS: N/A
O
IPU
DVDD
GPMC, VIN[1]A,
HDMI, SPI[2],
I2C[2], GP3
PINCNTL229
DSIS: N/A
O
IPU
DVDD
GPMC, VIN[1]A,
HDMI, SPI[2],
I2C[2], GP3
PINCNTL230
DSIS: N/A
O
IPD
DVDD_C
CAMERA_I/F,
GPMC, UART4,
GP0
PINCNTL170
DSIS: N/A
O
IPD
DVDD_C
CAMERA_I/F,
GPMC, UART4,
GP0
PINCNTL171
DSIS: N/A
O
IPD
DVDD
EMAC[1],
VIN[1]A, SPI[3],
UART3, GP2
PINCNTL206
DSIS: N/A
O
DESCRIPTION
Video Output Data. These signals represent the 8 MSBs
of R/CR video data. For RGB mode they are red data
bits, for YUV444 mode they are Cr (Chroma) data bits,
for Y/C mode and BT.656 mode they are not used.
Video Output Data. These signals represent the 8 MSBs
of R/CR video data. For RGB mode they are red data
bits, for YUV444 mode they are Cr (Chroma) data bits,
for Y/C mode and BT.656 mode they are not used.
Video Output Data. These signals represent the 2 LSBs
of R/CR video data for 30-bit video modes. For RGB
mode they are red data bits, for YUV444 mode they are
Cr (Chroma) data bits, for Y/C mode and BT.656 modes
they are not used. These signals are not used in 24-bit
mode.
Video Output Vertical Sync output. This is the discrete
vertical synchronization output. This signal is not used for
embedded sync modes
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
145
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-46. Video Output 1 Terminal Functions (continued)
SIGNAL
NAME
VOUT[1]_HSYNC/
EMAC[1]_MCOL/
VIN[1]A_VSYNC/
SPI[3]_D[1]/
UART3_RTS/
GP2[29]
VOUT[1]_FLD/
CAM_FLD/
CAM_WE/
GPMC_A[11]/
UART2_CTS/
GP0[28]
VOUT[1]_AVID/
EMAC[1]_MRXER/
VIN[1]A_CLK/
UART4_RTS/
TIM6_IO/
GP2[31]
146
Device Pins
NO.
AC24
AB23
Y22
TYPE (1)
OTHER (2)
(3)
MUXED
DESCRIPTION
IPD
DVDD
EMAC[1],
VIN[1]A, SPI[3],
UART3, GP2
PINCNTL205
DSIS: N/A
Video Output Horizontal Sync output. This is the discrete
horizontal synchronization output. This signal is not used
for embedded sync modes.
O
IPD
DVDD_C
CAMERA_I/F,
GPMC, UART2,
GP0
PINCNTL174
DSIS: N/A
Video Output Field ID output. This is the discrete field
identification output. This signal is not used for embedded
sync modes.
O
IPD
DVDD
EMAC[1],
VIN[1]A, UART4,
TIMER6, GP2
PINCNTL207
DSIS: N/A
Video Output Active Video output. This is the discrete
active video indicator output. This signal is not used for
embedded sync modes.
O
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.24 Video Output (Analog, TV)
Table 3-47. Video Outupt (Analog, TV) Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
VIDEO INTERFACES (TV)
Composite/S-Video (Luminance) Amplifier Output.
TV_OUT0
AH24
–
VDDA_VDAC_1P8
O
In Normal mode (internal amplifier used), this pin drives the 75-Ω TV
load. An external resistor (Rout) should be connected between this pin
and the TV_VFB0 pin and be placed as close to the pins as possible.
The nominal value of Rout is 2700 Ω.
In TVOUT Bypass mode (internal amplifier not used), this pin is not
used.
When this pin is not used or the TV output is powered-down, this pin
should be left unconnected.
S-Video (Chrominance) Amplifier Output.
TV_OUT1
AH22
In Normal mode (internal amplifier used), this pin drives the 75-Ω TV
load.
An external resistor (Rout) should be connected between this pin and
the TV_VFB1 pin and be placed as close to the pins as possible. The
–
VDDA_VDAC_1P8 nominal value of Rout is 2700 Ω.
In TVOUT Bypass mode (internal amplifier not used), this pin is not
used.
O
When this pin is not used or the TV output is powered-down, this pin
should be left unconnected.
Composite/S-Video (Luminance) Feedback.
In Normal mode (internal amplifier used), this pin acts as the buffer
feedback node.
An external resistor (Rout) should be connected between this pin and
the TV_OUT0 pin.
TV_VFB0
AG23
AO
–
VDDA_VDAC_1P8 In TVOUT Bypass mode (internal amplifier not used), this pin acts as
the direct Video DAC output and should be connected to ground
through a load resistor (Rload) and to an external video amplifier. The
nominal value of Rload is 1500 Ω.
When this pin is not used or the TV output is powered-down, this pin
should be left unconnected.
S-Video (Chrominance) Feedback.
In Normal mode (internal amplifier used), this pin acts as the buffer
feedback node.
An external resistor (Rout) should be connected between this pin and
the TV_OUT1 pin.
TV_VFB1
AG22
AO
–
VDDA_VDAC_1P8 In TVOUT Bypass mode (internal amplifier not used), it acts as the
direct Video DAC output and should be connected to ground through
a load resistor (Rload) and to an external video amplifier. The nominal
value of Rload is 1500 Ω.
When this pin is not used or the TV output is powered-down, this pin
should be left unconnected.
(1)
(2)
(3)
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
IPD = Internal Pulldown Active, IPU = Internal Pullup Active, DIS = Internal Pull Disabled. This represents the default state of the
Internal Pull after Reset. For more detailed information on pullup/pulldown resistors and situations where external pullup/pulldown
resistors are required, see Section 4.5.1, Pullup/Pulldown Resistors and Section 7.3.17, Pin Behaviors at Reset.
Specifies the operating I/O supply voltage for each signal
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
147
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 3-47. Video Outupt (Analog, TV) Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER (2)
(3)
DESCRIPTION
TV Input Reference Current Setting.
An external resistor (Rset) should be connected between this pin and
VSSA_VDAC to set the reference current of the video DAC. The value
of the resistor depends on the mode of operation.
TV_RSET
AH23
A
In Normal mode (internal amplifier used), the nominal value for Rset
–
VDDA_VDAC_1P8 is 4700 Ω.
In TVOUT Bypass mode (internal amplifier not used), the nominal
value for Rset is 10000 Ω.
When the TV output is not used, this pin should be connected to
ground (VSS).
148
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
3.2.25 Reserved Pins
Table 3-48. Reserved Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER
DESCRIPTION
RSV1
AD8
O
Reserved. (Leave unconnected, do not connect to power or ground.)
RSV2
U8
O
Reserved. (Leave unconnected, do not connect to power or ground.)
RSV3
V8
O
Reserved. (Leave unconnected, do not connect to power or ground.)
RSV4
Y14
I
RSV5
AC8
I
RSV6
L27
I
RSV7
L28
I
RSV8
M27
I
RSV9
M28
I
RSV10
N28
I
RSV11
N27
I
RSV12
P28
I
RSV13
P27
I
RSV14
R27
I
RSV15
R28
I
RSV16
U1
I
Reserved. (Leave unconnected, do not connect to power or ground.)
RSV17
U2
I
Reserved. (Leave unconnected, do not connect to power or ground.)
(1)
Reserved. (Leave unconnected, do not connect to power or ground.)
Reserved. (Leave unconnected, do not connect to power or ground.)
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
149
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3.2.26 Supply Voltages
Table 3-49. Supply Voltages Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER
DESCRIPTION
VREFSSTL_DDR[0]
G15
S
Reference Power Supply DDR[0]
VREFSSTL_DDR[1]
G14
S
Reference Power Supply DDR[1]
CVDD
K9, K12,
K18, L15,
L17, L19,
M16, M18,
N17, N19,
P12, P14,
P16, R15,
R17, R19,
T12, U11,
U13, U17,
U19, W11
S
Variable Voltage Supply for the CORE_L Core Logic Voltage
Domain
For actual voltage supply ranges, see Section 6.2, Recommended
Operating Conditions.
CVDD_ARM
T14, T15,
T16, U15,
U16, V15,
V16
S
Variable Voltage Supply for the ARM_L Core Logic Voltage
Domain
For actual voltage supply ranges, see Section 6.2, Recommended
Operating Conditions.
CVDD_DSP
K10, L9, L10,
L11, L12,
M10, M12,
N9
S
Variable Voltage Supply for the DSP_L Core Logic Voltage
Domain
For actual voltage supply ranges, see Section 6.2, Recommended
Operating Conditions.
CVDD_HDVICP
L14, M13,
M14, N13,
N14
S
Variable Voltage Supply for the HDVICP_L Core Logic Voltage
Domain
For actual voltage supply ranges, see Section 6.2, Recommended
Operating Conditions.
DVDD
M8, N7, P8,
T7, U21,
U22,
V20,Y11,
Y16, AA15,
AA17, AB14,
AB16
S
3.3 V/1.8 V Power Supply for General I/Os
DVDD_GPMC
K20, L21,
M20
S
3.3 V/1.8 V Power Supply for GPMC I/Os (that is, GPMC, SD2,
and so forth)
DVDD_GPMCB
P20, T20
S
3.3 V/1.8 V Power Supply for GPMCB I/Os
DVDD_SD
P7, P9
S
3.3 V/1.8 V Power Supply for MMC/SD/SDIO I/Os (specifically,
SD0, SD1, and pin W6)
DVDD_DDR[0]
E20, E21,
G16, H16,
H17, J15,
J16, J17, J18
S
1.5 V/1.8 V Power Supply for DDR[0] I/Os
DVDD_DDR[1]
E8, E9, G13,
H12, H13,
H14, J10,
J11, J13
S
1.5 V/1.8 V Power Supply for DDR[1] I/Os
DVDD_M
R10
S
1.8 V Power Supply . For proper device operation, this pin must
always be connected to a 1.8-V Power Supply.
DVDD_C
W19, W20
S
3.3 V/1.8 V Power Supply for Camera I/F I/Os
VDDA_ARMPLL_1P8
R13
S
1.8 V Analog Power Supply for PLL_ARM and PLL_SGX
VDDA_DSPPLL_1P8
P11
S
1.8 V Analog Power Supply for PLL_DSP and PLL_HDVICP
VDDA_VID0PLL_1P8
AB18
S
1.8 V Analog Power Supply for PLL_VIDEO0
VDDA_VID1PLL_1P8
AA18
S
1.8 V Analog Power Supply for PLL_VIDEO1
VDDA_AUDIOPLL_1P8
R18
S
1.8 V Analog Power Supply for PLL_AUDIO
VDDA_DDRPLL_1P8
H15
S
1.8 V Analog Power Supply for PLL_DDR
(1)
150
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 3-49. Supply Voltages Terminal Functions (continued)
SIGNAL
NAME
NO.
TYPE (1)
OTHER
DESCRIPTION
VDDA_L3PLL_1P8
N18
S
1.8 V Analog Power Supply for PLL_L3, PLL_HDVPSS, and
PLL_MEDIACTL
VDDA_PCIE_1P8
W9, W10
S
1.8 V Analog Power Supply for PCIe.
For proper device operation, this pin must always be connected
to a 1.8-V Power Supply, even if the PCIe is not being used.
VDDA_SATA_1P8
U9, U10
S
1.8 V Analog Power Supply for SATA.
For proper device operation, this pin must always be connected
to a 1.8-V Power Supply, even if the SATA is not being used.
VDDA_HDMI_1P8
W18
S
1.8 V Analog Power Supply for HDMI.
For proper device operation, this pin must always be connected
to a 1.8-V Power Supply, even if the HDMI is not being used.
VDDA_USB0_1P8
AA12
S
1.8 V Analog Power Supply for USB0.
For proper device operation, this pin must always be connected
to a 1.8-V Power Supply, even if the USB0 is not being used.
VDDA_USB1_1P8
W13
S
1.8 V Analog Power Supply for USB1.
For proper device operation, this pin must always be connected
to a 1.8-V Power Supply, even if the USB1 is not being used.
VDDA_VDAC_1P8
AB19
S
1.8 V Reference Power Supply for VDAC.
For proper device operation, this pin must always be connected
to a 1.8-V Power Supply, even if the VDAC is not being used.
VDDA_USB_3P3
AA13
S
3.3 V Analog Power Supply for USB0 and USB1.
For proper device operation, this pin must always be connected
to a 3.3-V Power Supply, even if USB0 and USB1 are not being
used.
VDDA_1P8
L20, M7,
M22, R20,
U7, V10,
W15, Y13
S
1.8 V Power Supply for on-chip LDOs and I/O biasing
LDOCAP_ARM
W14
A
ARM Cortex-A8 VBB LDO output.
This pin must always be connected via a 1-uF capacitor to VSS.
LDOCAP_ARMRAM
V14
A
ARM Cortex-A8 RAM LDO output.
This pin must always be connected via a 1-uF capacitor to VSS.
LDOCAP_RAM0
P18
A
CORE RAM0 LDO output.
This pin must always be connected via a 1-uF capacitor to VSS.
LDOCAP_RAM1
R11
A
CORE RAM1 LDO output.
This pin must always be connected via a 1-uF capacitor to VSS.
LDOCAP_RAM2
L18
A
CORE RAM2 LDO output.
This pin must always be connected via a 1-uF capacitor to VSS.
LDOCAP_DSP
P10
A
C674x DSP VBB LDO output.
This pin must always be connected via a 1-uF capacitor to VSS.
LDOCAP_DSPRAM
M11
A
C674x DSP RAM LDO output.
This pin must always be connected via a 1-uF capacitor to VSS.
LDOCAP_HDVICP
N10
A
HDVICP2 VBB LDO output.
This pin must always be connected via a 1-uF capacitor to VSS.
LDOCAP_HDVICPRAM
N11
A
HDVICP2 RAM LDO output.
This pin must always be connected via a 1-uF capacitor to VSS.
LDOCAP_SGX
T10
A
SGX530 VBB LDO output.
This pin must always be connected via a 1-uF capacitor to VSS.
LDOCAP_SERDESCLK
T11
A
SERDES_CLKP/N Pins LDO output.
This pin must always be connected via a 1-uF capacitor to VSS.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Pins
151
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
3.2.27 Ground Pins (VSS)
Table 3-50. Ground Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
OTHER
DESCRIPTION
VSS
A1, A12,
A17, A28,
D9, D20, J12,
J14, J19,
K11, K13,
K14, K15,
K16, K17,
K19, L8, L13,
L16, L22, M9,
M15, M17,
M19, M21,
N8, N12,
N15, N16,
N20, N21,
N22, P13,
P15, P17,
P19, P21,
R8, R9, R12,
R14, R16,
R21, R22,
T8, T9, T13,
T17, T18,
T19, T21,
T22, U12,
U14, U18,
U20, V7, V9,
V11, V17,
V19, V21,
W12, W16,
W17, Y1, Y2,
Y10, Y12,
Y15, Y17,
Y18, Y19,
AA14, AA16,
AD21, AE1,
AE2, AE9,
AE20, AF23,
AG1, AH1,
AH28
GND
Ground (GND)
VSSA_VDAC
AA19
GND
Analog GND for VDAC.
For proper device operation, this pin must always be connected to ground,
even if the VDAC is not being used.
VSSA_HDMI
V18
GND
Analog GND for HDMI
For proper device operation, this pin must always be connected to ground,
even if the HDMI is not being used.
VSSA_USB
V12, V13
GND
Analog GND for USB0 and USB1.
For proper device operation, this pin must always be connected to ground,
even if USB0 and USB1 are not being used.
VSSA_DEVOSC
AG3
GND
Ground for Device Oscillator
VSSA_AUXOSC
R2
GND
Ground for Auxiliary Oscillator
(1)
152
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, MM = Multi Muxed, DSIS = Deselected Input State
Device Pins
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
4 Device Configurations
4.1
Control Module Registers
4.2
Boot Modes
The state of the device after boot is determined by sampling the input states of the BTMODE[15:0] pins
when device reset (POR or RESET) is de-asserted. The sampled values are latched into the
CONTROL_STATUS register, which is part of the Control Module. The BTMODE[15:11] values determine
the following system boot settings:
• RSTOUT_WD_OUT Control
• GPMC CS0 Default Data Bus Width, Wait Enable, and Address/Data Multiplexing
For additional details on BTMODE[15:11] pin functions, see Table 3-1, Boot Configuration Terminal
Functions.
The BTMODE[4:0] values determine the boot mode order according to Table 4-1, Boot Mode Order. The
1st boot mode listed for each BTMODE[4:0] configuration is executed as the primary boot mode. If the
primary boot mode fails, the 2nd, 3rd, and 4th boot modes are executed in that order until a successful
boot is completed.
The BTMODE[7:5] pins are RESERVED and should be pulled down as indicated inTable 3-1, Boot
Configuration Terminal Functions.
When the EMAC bootmode is selected (see Table 4-1), the sampled value from BTMODE[9:8] pins are
used to determine the Ethernet PHY Mode selection (see Table 4-7).
When the XIP (MUX0), XIP (MUX1), XIP w/ WAiT (MUX0) or XIP w/ WAiT (MUX1) bootmode is selected
(see Table 4-1), the sampled value from BTMODE[10] pin is used to select between GPMC pin muxing
options shown in Table 4-2, XIP (on GPMC) Boot Options [Muxed or Non-Muxed].
For more detailed information on booting the device, see the ROM Code Memory and Peripheral Booting
chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature
Number: SPRUGZ8).
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Configurations
153
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 4-1. Boot Mode Order
BTMODE[4:0]
1st
2nd
3rd
4th
00000
RESERVED
RESERVED
RESERVED
RESERVED
00001
UART
XIP w/WAIT (MUX0) (1) (2)
MMC
SPI
00010
UART
SPI
NAND
NANDI2C
00011
UART
SPI
XIP (MUX0) (1) (2)
MMC
SPI
NAND
NANDI2C
RESERVED
00100
EMAC
00101
RESERVED
RESERVED
RESERVED
00110
RESERVED
RESERVED
RESERVED
RESERVED
00111
EMAC (3)
MMC
SPI
XIP (MUX1) (1) (2)
01000
PCIE_32 (4)
RESERVED
RESERVED
RESERVED
01001
PCIE_64
(4)
RESERVED
RESERVED
RESERVED
01010
RESERVED
RESERVED
RESERVED
RESERVED
01011
RESERVED
RESERVED
RESERVED
RESERVED
01100
RESERVED
RESERVED
RESERVED
RESERVED
01101
RESERVED
RESERVED
RESERVED
RESERVED
01110
RESERVED
RESERVED
RESERVED
RESERVED
01111
Fast XIP (MUX0) (1)
UART
EMAC (3)
PCIE_64 (4)
(3)
10000
XIP (MUX1)
(2)
(3)
(4)
(1) (2)
UART
EMAC
10001
XIP w/WAIT (MUX1) (1) (2)
UART
EMAC (3)
MMC
10010
NAND
NANDI2C
SPI
UART
10011
NAND
NANDI2C
MMC
UART
10100
NAND
NANDI2C
SPI
EMAC (3)
10101
NANDI2C
MMC
EMAC (3)
UART
10110
SPI
MMC
UART
EMAC (3)
10111
MMC
SPI
UART
MMC
EMAC (3)
(4)
RESERVED
11000
SPI
MMC
PCIE_32
11001
SPI
MMC
PCIE_64 (4)
RESERVED
MMC
11010
(1)
(3)
XIP (MUX0)
(1) (2)
UART
SPI
11011
XIP w/WAIT (MUX0) (1) (2)
UART
SPI
MMC
11100
RESERVED
RESERVED
RESERVED
RESERVED
11101
RESERVED
RESERVED
RESERVED
RESERVED
11110
RESERVED
RESERVED
RESERVED
RESERVED
11111
Fast XIP (MUX0) (1)
EMAC (3)
UART
PCIE_32 (4)
GPMC CS0 eXecute In Place (XIP) boot for NOR/OneNAND/ROM. MUX0/1 refers to the multiplexing option for the GPMC_A[12:0] pins.
For more detailed information on booting the device, including which pins are used for each boot mode, see the ROM Code Memory
and Peripheral Booting chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature
Number: SPRUGZ8).
When the XIP (MUX0), XIP (MUX1), XIP w/ WAiT (MUX0) or XIP w/ WAiT (MUX1) bootmode is selected, the sampled value from
BTMODE[10] pin is used to select between GPMC pin configuration options shown in Table 4-2, XIP (on GPMC) Boot Options.
When the EMAC bootmode is selected, the sampled value from BTMODE[9:8] pins are used to determine the Ethernet PHY Mode
Selection (see Table 4-7).
When the PCIe bootmode is selected (PCIE_32 or PCI_64), the sampled value from BTMODE[15:12] pins are used to determine the
addressing options. For more detailed information on the PCIe addressing options, see the ROM Code Memory and Peripheral Booting
chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number: SPRUGZ8).
4.2.1
XIP (NOR) Boot Options
Table 4-2 shows the XIP (NOR) boot mode GPMC pin configuration options (Option A: BTMODE[10] = 0
and Option B: BTMODE[10] = 1). For Option B, the pull state on select pins is reconfigured to IPD and
remains IPD after boot until the user software reconfigures it.
154
Device Configurations
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 4-2. XIP (on GPMC) Boot Options
CONTROLLED I/O FUNCTION DURING XIP (NOR) BOOT
SIGNAL NAME
PIN NO.
OTHER CONDITIONS
BTMODE[10] = 0 [OPTION A]
PIN FUNCTION
GPMC_CS[0]/*
T28
M26
GPMC_ADV_ALE/*
BTMODE[14:13] = 01b or 10b (Mux)
BTMODE[10] = 1 [OPTION B]
PULL
STATE
PIN FUNCTION
PULL
STATE
GPMC_CS[0]
IPU
GPMC_CS[0]
IPU
GPMC_ADV_ALE
IPU
GPMC_ADV_ALE
IPU
BTMODE[14:13] = 00b (Non-Mux)
Default
GPMC_OE_RE
T27
GPMC_OE_RE
IPU
GPMC_OE_RE
IPU
GPMC_BE[0]_CLE/GPMC_A[25]/*
U27
GPMC_BE[0]_CLE
IPD
Default
IPD
GPMC_BE[1]/GPMC_A[24]/*
V28
Default
IPD
Default
IPD
GPMC_WE
U28
GPMC_WE
IPU
GPMC_WE
IPU
GPMC_WAIT[0]
IPU
GPMC_WAIT[0]
W28
BTMODE[15] = 1b (WAIT Used/Enabled)
GPMC_WAIT[0]/GPMC_A[26]/*
BTMODE[15] = 0b (WAIT Not
Used/Disabled)
GPMC_CLK/*
GPMC_D[15:0]/*
R26
Y25,V24,U23,U24,AA27,Y26,AB
28,Y27,V25,U25,AA28,V26,W27,
V27,Y28,U26
J25
*/GPMC_A[27]/GPMC_A[26]/GPMC_A[0]/*
BTMODE[12] = 0b (8-bit Mode)
IPU
Default
IPD (1)
GPMC_CLK
IPU
Default
IPU
GPMC_D[15:0]
Off
GPMC_D[15:0]
Off
GPMC_A[0]
IPD
GPMC_A[0]
IPD
BTMODE[12] = 1b (16-bit Mode)
Default
*/GPMC_A[1:12]/* (M0)
T23,H26,F28,G27,K22,K23,J24,
H25,H22,H23,G23,F27
XIP_MUX0 Mode
GPMC_A[1:12]
IPD
GPMC_A[1:12]
XIP_MUX1 Mode
Default
IPD
Default
IPD
XIP_MUX0 Mode
Default
Default
Default
Default
*/GPMC_A[1:12]/* (M1)
J28,K27,M24,L26,AD18,AC18,A
C19,AA22,AE23,AD23,AB23,AF
18
XIP_MUX1 Mode
GPMC_A[1:12]
Default
GPMC_A[1:12]
Default
*/GPMC_A[13:15]/* (M0)
J22,H24,J23
AF28
*/GPMC_A[0]/* (M1)
BTMODE[12] = 0b (8-bit Mode)
IPD
Default
IPD
Default
IPD
Default
IPU
Default
IPU
Default
IPU
Default
BTMODE[12] = 1b (16-bit Mode)
AF27
*/GPMC_A[13]/* (M1)
BTMODE[14:13] = 01b or 10b (Mux)
IPU
IPD (1)
BTMODE[14:13] = 00b (Non-Mux)
AG28
*/GPMC_A[14]/* (M1)
BTMODE[14:13] = 01b or 10b (Mux)
Default
IPU
Default
IPU
IPD (1)
BTMODE[14:13] = 00b (Non-Mux)
*/GPMC_A[15]/* (M1)
AE27
Default
IPD
Default
GPMC_A[16:19]/*
AD27,V23,AE28,AC27
Default
IPD
Default
IPD
GPMC_A[20] (M0)
AD28
Default
IPU
Default
IPD (1)
GPMC_A[21] (M0)
AC28
Default
IPD
Default
IPD
GPMC_A[22] (M0)
AB27
Default
IPU
Default
IPD (1)
GPMC_A[23] (M0)
AA26
Default
IPD
Default
IPD
(1)
IPD
After initial power-up the internal pullup (IPU) will be at its default configuration of IPU. During the boot ROM execution, the pull state is reconfigured to IPD and it remains IPD after boot
until the user software reconfigures it.
Device Configurations
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
155
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 4-2. XIP (on GPMC) Boot Options (continued)
CONTROLLED I/O FUNCTION DURING XIP (NOR) BOOT
SIGNAL NAME
PIN NO.
OTHER CONDITIONS
BTMODE[10] = 0 [OPTION A]
PIN FUNCTION
BTMODE[10] = 1 [OPTION B]
PULL
STATE
PIN FUNCTION
PULL
STATE
*/GPMC_A[24]/GPMC_A[20]/*
L25
Default
IPU
Default
IPD (1)
*/GPMC_A[25]/GPMC_A[21]/*
N23
Default
IPU
Default
IPD (1)
*/GPMC_A[26]/GPMC_A[22]/*
P22
Default
IPU
Default
IPD (1)
*/GPMC_A[27]/GPMC_A[23]/*
R24
Default
IPU
Default
IPU
GPMC_A[24] (M1)
M25
Default
IPU
Default
IPU
GPMC_A[25] (M1)
K28
Default
IPU
Default
IPU
156
Device Configurations
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
4.2.2
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
NAND Flash Boot
Table 4-3 lists the device pins that are configured by the ROM for the NAND Flash boot mode.
NOTE: Table 4-3 lists the configuration of the GPMC_CLK pin (pin mux and pull state) in NAND
bootmodes.
The NAND flash memory is not XIP and requires shadowing before the code can be executed.
Table 4-3. Pins Used in NAND FLASH Bootmode
(1)
4.2.3
OTHER
CONDITIONS
SIGNAL NAME
PIN NO.
TYPE
GPMC_CS[0]/*
T28
O
GPMC_ADV_ALE/*
M26
O
GPMC_OE_RE
T27
O
GPMC_BE[0]_CLE/GPMC_A[25]/*
U27
O
GPMC_BE[1]/GPMC_A[24]/*
V28
O
GPMC_WE
U28
O
GPMC_WAIT[0]/GPMC_A[26]/* (1)
W28
I
GPMC_CLK/*
R26
O
BTMODE[14:13] =
00b (GPMC CS0
not muxed)
GPMC_D[15:0]/*
Y25,V24,U23,U24,
AA27,Y26,AB28,Y2
7,
V25,U25,AA28,V26
,W27,V27,Y28,U26
I/O
BTMODE[15] = 0b
(wait disabled)
BTMODE[12] = 0b
(8-bit Mode)
BTMODE[12] = 1b
(16-bit Mode)
GPMC_CLK/* is not configured in BTMODE[10] = 1 [OPTION B]
NAND I2C Boot (I2C EEPROM)
Table 4-4 lists the device pins that are configured by the ROM for the NAND I2C boot mode.
Table 4-4. Pins Used in NAND I2C Bootmode
SIGNAL NAME
4.2.4
PIN NO.
TYPE
I2C[0]_SCL
AC4
I/O
I2C[0]_SDA
AB6
I/O
MMC/SD Cards Boot
Table 4-5 lists the device pins that are configured by the ROM for the MMC/SD boot mode.
Table 4-5. Pins Used in MMC/SD Bootmode
PIN NO.
TYPE
SD1_CLK
SIGNAL NAME
P3
O
SD1_CMD/GP0[0] [MUX0]
P2
O
SD1_DAT[0]
P1
I/O
SD1_DAT[1]_SDIRQ
P5
I/O
SD_DAT[2]_SDRW
P4
I/O
SD1_DAT[3]
P6
I/O
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Configurations
157
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
4.2.5
www.ti.com
SPI Boot
Table 4-6 lists the device pins that are configured by the ROM for the SPI boot mode.
Table 4-6. Pins Used in SPI Bootmode
SIGNAL NAME
4.2.6
PIN NO.
TYPE
SPI[0]_SCS[0]
AD6
I/O
SPI[0]_D[0] (MISO)
AE3
I/O
SPI[0]_D[1] (MOSI)
AF3
I/O
SPI[0]_SCLK
AC7
I/O
Ethernet PHY Mode Selection
When the EMAC bootmode is selected, via the BTMODE[4:0] pins (see Table 4-1), Table 4-7 shows the
sampled value of BTMODE[9:8] pins and the Ethernet PHY Mode selection.
Table 4-8 shows the signal names (pin functions) and the associated pin numbers selected in each
particular EMAC mode.
Table 4-7. EMAC PHY Mode Selection
BTMODE[9:8]
ETHERNET PHY MODE
SELECTION
00b
MII
01b
RMII
10b
RGMII
11b
RESERVED
Table 4-8. Pins Used in EMAC[0] MII/GMII, RGMII, and RMII Boot Modes
SIGNAL NAMES
PIN NO.
J27
158
MII/GMII
TYPE
DEFAULT
RGMII
TYPE
DEFAULT
RMII
TYPE
EMAC_RMREFCLK
Output
only
L23
EMAC[0]_MCOL
I
EMAC[0]_RGRXCTL
I
EMAC[0]_RMRXD[0]
I
R25
EMAC[0]_MCRS
I
EMAC[0]_RGRXD[2]
I
EMAC[0]_RMRXD[1]
I
K23
EMAC[0]_GMTCLK
O
DEFAULT
H27
EMAC[0]_MRCLK
I
EMAC[0]_RGTXC
O
EMC[0]_RMCRSDV
DEFAULT
I
G28
EMAC[0]_MRXD[0]
I
EMAC[0]_RGTXD[0]
O
EMAC[0]_RMTXD[0]
O
P23
EMAC[0]_MRXD[1]
I
EMAC[0]_RGRXD[0]
I
EMAC[0]_RMTXD[1]
O
R23
EMAC[0]_MRXD[2]
I
EMAC[0]_RGRXD[1]
I
EMAC[0]_RMTXEN
O
J25
EMAC[0]_MRXD[3]
I
DEFAULT
DEFAULT
T23
EMAC[0]_MRXD[4]
I
EMAC[0]_RGRXD[3]
I
DEFAULT
H26
EMAC[0]_MRXD[5]
I
EMAC[0]_RGTXD[3]
O
DEFAULT
F28
EMAC[0]_MRXD[6]
I
EMAC[0]_RGTXD[2]
O
DEFAULT
G27
EMAC[0]_MRXD[7]
I
EMAC[0]_RGTXD[1]
O
DEFAULT
K22
EMAC[0]_MRXDV
I
DEFAULT
J26
EMAC[0]_MRXER
I
EMAC[0]_RGTXCTL
O
EMAC[0]_RMRXER
L24
EMAC[0]_MTCLK
I
EMAC[0]_RGRXC
I
DEFAULT
DEFAULT
J24
EMAC[0]_MTXD[0]
O
DEFAULT
DEFAULT
H25
EMAC[0]_MTXD[1]
O
DEFAULT
DEFAULT
H22
EMAC[0]_MTXD[2]
O
DEFAULT
DEFAULT
Device Configurations
I
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 4-8. Pins Used in EMAC[0] MII/GMII, RGMII, and RMII Boot Modes (continued)
SIGNAL NAMES
PIN NO.
4.2.7
MII/GMII
TYPE
RGMII
TYPE
RMII
H23
EMAC[0]_MTXD[3]
O
DEFAULT
DEFAULT
G23
EMAC[0]_MTXD[4]
O
DEFAULT
DEFAULT
F27
EMAC[0]_MTXD[5]
O
DEFAULT
DEFAULT
TYPE
J22
EMAC[0]_MTXD[6]
O
DEFAULT
DEFAULT
H24
EMAC[0]_MTXD[7]
O
DEFAULT
DEFAULT
J23
EMAC[0]_MTXEN
O
DEFAULT
DEFAULT
H28
MDCLK
O
MDCLK
O
MDCLK
O
P24
MDIO
I/O
MDIO
I/O
MDIO
I/O
PCIe Bootmode (PCIE_32 and PCIE_64)
Table 4-9 lists the device pins that are configured by the ROM for the PCIe boot mode.
Table 4-9. Pins Used in PCIe Bootmode
SIGNAL NAME
4.2.8
PIN NO.
TYPE
PCIE_TXP0
AD2
O
PCIE_TXN0
AD1
O
PCIE_RXP0
AC2
I
PCIE_RXN0
AC1
I
SERDES_CLKIP
AF1
I
SERDES_CLKN
AF2
I
UART Bootmode
Table 4-10 lists the device pins that are configured by the ROM for the UART boot mode.
Table 4-10. Pins Used in UART Bootmode
SIGNAL NAME
4.3
PIN NO.
TYPE
UART0_RXD
AH5
I
UART0_TXD
AG5
O
Pin Multiplexing Control
Device level pin multiplexing is controlled on a pin-by-pin basis by the MUXMODE bits of the PINCNTL1 –
PINCNTL270 registers in the Control Module.
Pin multiplexing selects which one of several peripheral pin functions controls the pin's I/O buffer output
data values. Table 4-11 shows the peripheral pin functions associated with each MUXMODE setting for all
multiplexed pins. The default pin multiplexing control for almost every pin is to select MUXMODE = 0x0, in
which case the pin's I/O buffer is 3-stated.
In most cases, the input from each pin is routed to all of the peripherals that share the pin, regardless of
the MUXMODE setting. However, in some cases a constant "0" or "1" value is routed to the associated
peripheral when its peripheral function is not selected to control any output pin. For more details on the
De-Selected Input State (DSIS), see the "MUXED" columns of each Terminal Functions table (Section 3.2,
Terminal Functions).
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Configurations
159
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Some peripheral pin functions can be routed to more than one device pin. These types of peripheral pin
functions are called Multimuxed (MM) and may have different Switching Characteristics and Timing
Requirements for each device pin option. The Multimuxed peripheral pin functions are labeled as "MM" in
Terminal Functions tables in Section 3.2, Terminal Functions and the associated timings for each MM pin
option are in Section 8, Peripheral Information and Timings.
For more detailed information on the Pin Control 1 through Pin Control 270 (PINCNTLx) registers
breakout, see Figure 4-1 and Table 4-11. For the register reset values of each PINCNTLx register, see
Table 4-13, PINCNTLx Registers MUXMODE Functions.
Figure 4-1. PINCNTL1 – PINCNTL270 (PINCNTLx) Registers Breakout
31
24
23
20
RESERVED
RESERVED
R - 0000 0000
R - 0000
15
8
19
18
17
16
RSV
RXAC
TIVE
PLLTY
PESE
L
PLLU
DEN
R/W (see Table 4-13 for register
reset value)
7
0
RESERVED
MUXMODE[7:0] (see Table 4-13)
R - 0000 0000
R/W - 0000 0000
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 4-11. PINCNTL1 – PINCNTL270 (PINCNTLx) Registers Bit Descriptions
Bit
31:20
Field
Description
Comments
RESERVED
Reserved. Read only, writes have no effect.
19
RSV
Reserved. This bit must always be written with the
reset (default) value.
(See Table 4-13 for full register reset value)
18
RXACTIVE
Receiver Enable
0 = Receiver Disabled
1 = Receiver Enabled
For PINCNTLx register reset value
examples, see Table 4-12,
PNICNTLx Register Reset Value
Examples.
Pullup/Pulldown Type Selection bit
17
PLLTYPSEL
16
PLLUDEN
0 = PU/PD enabled
1 = PU/PD disabled
RESERVED
Reserved. Read only, writes have no effect.
0 = Pulldown (PD) selected
1 = Pullup (PU) selected
For the full register reset values of all
PINCNTLx registers, see Table 4-13,
PINCNTLx Registers MUXMODE
Functions.
Pullup/Pulldown Enable bit
15:8
MUXMODE Selection bits
7:0
160
MUXMODE[7:0]
Device Configurations
These bits select the multiplexed mode pin function
settings (seeTable 4-13, PINCNTLx Registers
MUXMODE Functions). A value of zero results in the
pin being tri-stated. Non-zero values other than those
shown in Table 4-13 are Reserved.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 4-12. PINCNTLx Register Reset Value Examples
HEX
ADDRESS
RANGE
PINCNTLx
REGISTER
NAME
Bits 31:24
Bits 23:20
Bit 19
Bit 18
Bit 17
Bit 16
Bits 15:8
Bits 7:0
REGISTER
RESET
VALUE
RESERVED
RESERVED
RSV
RSV
PLLTYPESEL
PLLUDEN
RESERVED
MUXMODE[7:0]
0x4814 0800
PINCNTL1
00h
0h
0
1
1
0
00h
00h
0x0006 0000
0x4814 0804
PINCNTL2
00h
0h
1
1
1
0
00h
00h
0x000E 0000
0x4814 0808
PINCNTL3
00h
0h
1
1
1
0
00h
00h
0x000E 0000
0x4814 0C34
PINCNTL270
00h
0h
1
1
0
0
00h
00h
0x000C 0000
…
(1) "(M0)" represents multimuxed option "0" for this pin function, "(M1)" represents multimuxed option "1" for this pin function, ... etc.
(2) Within this MUXMODE setting, EMAC[x] GMII or RGMII pin functions are selected via the RGMII0_EN and/or RGMII1_EN bits (8 and 9, respectively) in the GMII_SEL register
[0x4814_0650] of the Control Module. "0" = GMII (default) and "1" = RGMII.
Table 4-13. PINCNTLx Registers MUXMODE Functions
HEX
ADDRESS
REGISTER
NAME
PIN
NO.
REGISTER
RESET
VALUE
MUXMODE[7:0] SETTINGS
0x4814 0800
PINCNTL1
P3
0x0006 0000
SD1_CLK
0x4814 0804
PINCNTL2
P2
0x000E 0000
SD1_CMD(M0)
0x4814 0808
PINCNTL3
P1
0x000E 0000
SD1_DAT[0]
0x4814 080C
PINCNTL4
P5
0x000E 0000
SD1_DAT[1]_SDIRQ
0x4814 0810
PINCNTL5
P4
0x000E 0000
SD1_DAT[2]_SDRW
0x4814 0814
PINCNTL6
P6
0x000E 0000
SD1_DAT[3]
0x4814 0818
PINCNTL7
W6
0x000E 0000
DEVOSC_WAKE
0x4814 081C
PINCNTL8
Y6
0x0006 0000
SD0_CLK
0x4814 0820
PINCNTL9
N1
0x000E 0000
SD0_CMD
SD1_CMD(M1)
GP0[2]
0x4814 0824
PINCNTL10
R7
0x000E 0000
SD0_DAT[0]
SD1_DAT[4]
GP0[3]
0x4814 0828
PINCNTL11
Y5
0x000E 0000
SD0_DAT[1]_SDIRQ
SD1_DAT[5]
GP0[4]
0x4814 082C
PINCNTL12
Y3
0x000E 0000
SD0_DAT[2]_SDRW
SD1_DAT[6]
GP0[5]
0x4814 0830
PINCNTL13
Y4
0x000E 0000
SD0_DAT[3]
SD1_DAT[7]
0x4814 0834
PINCNTL14
L5
0x000C 0000
AUD_CLKIN0
(M1)
MCA[0]_AXR[7]
MCA[0]_AHCLKX
MCA[3]_AHCLKX
0x1
0x2
0x4
0x8
0x10
0x20
0x40
0x80
GP0[0]
SPI[1]_SCS[1]
TIM5_IO(M1)
GP1[7](M0)
GP0[1]
GP0[6]
USB1_DRVVBU
S
0x4814 0838
PINCNTL15
R5
0x000C 0000
AUD_CLKIN1
MCA[0]_AXR[8](M1)
MCA[1]_AHCLKX
MCA[4]_AHCLKX
EDMA_EVT3(M1)
TIM2_IO(M1)
GP0[8]
0x4814 083C
PINCNTL16
H1
0x000C 0000
AUD_CLKIN2
MCA[0]_AXR[9](M1)
MCA[2]_AHCLKX
MCA[5]_AHCLKX
EDMA_EVT2(M1)
TIM3_IO(M1)
GP0[9]
0x4814 0840
PINCNTL17
R4
0x0004 0000
MCA[0]_ACLKX
0x4814 0844
PINCNTL18
L3
0x000C 0000
MCA[0]_AFSX
0x4814 0848
PINCNTL19
K2
0x0004 0000
MCA[0]_ACLKR
MCA[5]_AXR[2]
0x4814 084C
PINCNTL20
K1
0x000C 0000
MCA[0]_AFSR
MCA[5]_AXR[3]
Device Configurations
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
161
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 4-13. PINCNTLx Registers MUXMODE Functions (continued)
HEX
ADDRESS
REGISTER
NAME
PIN
NO.
REGISTER
RESET
VALUE
MUXMODE[7:0] SETTINGS
0x4814 0850
PINCNTL21
J2
0x000C 0000
MCA[0]_AXR[0]
0x4814 0854
PINCNTL22
J1
0x000E 0000
MCA[0]_AXR[1]
I2C[3]_SCL(M0)
0x4814 0858
PINCNTL23
L4
0x000E 0000
MCA[0]_AXR[2]
I2C[3]_SDA(M0)
0x4814 085C
PINCNTL24
M5
0x000C 0000
MCA[0]_AXR[3]
0x4814 0860
PINCNTL25
R6
0x000C 0000
MCA[0]_AXR[4]
MCA[1]_AXR[8](M0)
0x4814 0864
PINCNTL26
M3
0x000C 0000
MCA[0]_AXR[5]
MCA[1]_AXR[9](M0)
0x4814 0868
PINCNTL27
M4
0x000C 0000
MCA[0]_AXR[6]
MCB_DR
0x4814 086C
PINCNTL28
L2
0x000C 0000
MCA[0]_AXR[7](M0)
MCB_DX
0x4814 0870
PINCNTL29
L1
0x000C 0000
(M0)
MCB_FSX
MCB_FSR(M1)
0x4814 0874
PINCNTL30
M6
0x000C 0000
(M0)
MCA[0]_AXR[9]
MCB_CLKX
MCB_CLKR(M1)
0x1
0x2
MCA[0]_AXR[8]
0x4
0x8
0x10
0x20
0x40
0x80
0x4814 0878
PINCNTL31
U5
0x0004 0000
MCA[1]_ACLKX
0x4814 087C
PINCNTL32
V3
0x000C 0000
MCA[1]_AFSX
0x4814 0880
PINCNTL33
M1
0x0004 0000
MCA[1]_ACLKR
MCA[1]_AXR[4]
0x4814 0884
PINCNTL34
M2
0x000C 0000
MCA[1]_AFSR
MCA[1]_AXR[5]
0x4814 0888
PINCNTL35
V4
0x000E 0000
MCA[1]_AXR[0]
SD0_DAT[4]
0x4814 088C
PINCNTL36
T6
0x000E 0000
MCA[1]_AXR[1]
SD0_DAT[5]
0x4814 0890
PINCNTL37
R3
0x000C 0000
MCA[1]_AXR[2]
MCB_FSR(M0)
0x4814 0894
PINCNTL38
N6
0x000C 0000
MCA[1]_AXR[3]
MCB_CLKR(M0)
0x4814 0898
PINCNTL39
U6
0x0006 0000
MCA[2]_ACLKX
GP0[10](M1)
0x4814 089C
PINCNTL40
AA5
0x000E 0000
MCA[2]_AFSX
GP0[11](M1)
0x4814 08A0
PINCNTL41
N2
0x000E 0000
MCA[2]_AXR[0]
SD0_DAT[6]
UART5_RXD(M3)
0x4814 08A4
PINCNTL42
V6
0x000E 0000
MCA[2]_AXR[1]
SD0_DAT[7]
(M3)
0x4814 08A8
PINCNTL43
V5
0x000C 0000
MCA[2]_AXR[2]
MCA[1]_AXR[6]
(M0)
TIM2_IO
GP0[14](M1)
0x4814 08AC
PINCNTL44
H2
0x000C 0000
MCA[2]_AXR[3]
MCA[1]_AXR[7]
TIM3_IO(M0)
GP0[15](M1)
0x4814 08B0
PINCNTL45
G6
0x0004 0000
MCA[3]_ACLKX
0x4814 08B4
PINCNTL46
H4
0x000C 0000
MCA[3]_AFSX
0x4814 08B8
PINCNTL47
G1
0x000C 0000
MCA[3]_AXR[0]
0x4814 08BC
PINCNTL48
G2
0x000C 0000
MCA[3]_AXR[1]
0x4814 08C0
PINCNTL49
F2
0x000C 0000
MCA[3]_AXR[2]
0x4814 08C4
PINCNTL50
J6
0x000C 0000
MCA[3]_AXR[3]
0x4814 08C8
PINCNTL51
K7
0x0004 0000
MCA[4]_ACLKX
GP0[21](M1)
0x4814 08CC
PINCNTL52
H3
0x000C 0000
MCA[4]_AFSX
GP0[22](M1)
0x4814 08D0
PINCNTL53
H6
0x000C 0000
MCA[4]_AXR[0]
GP0[23](M1)
0x4814 08D4
PINCNTL54
J4
0x000C 0000
MCA[4]_AXR[1]
162
UART5_TXD
GP0[12](M1)
GP0[13](M1)
GP0[16](M1)
GP0[17](M1)
(M0)
TIM4_IO
GP0[18](M1)
TIM5_IO(M0)
GP0[19](M1)
(M1)
GP0[20](M1)
MCA[1]_AXR[8]
(M1)
MCA[1]_AXR[9]
TIM6_IO(M0)
Device Configurations
GP0[24](M1)
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 4-13. PINCNTLx Registers MUXMODE Functions (continued)
HEX
ADDRESS
REGISTER
NAME
PIN
NO.
REGISTER
RESET
VALUE
MUXMODE[7:0] SETTINGS
0x4814 08D8
PINCNTL55
J3
0x000C 0000
MCA[5]_ACLKX
GP0[25](M1)
0x4814 08DC
PINCNTL56
H5
0x000C 0000
MCA[5]_AFSX
GP0[26](M1)
0x4814 08E0
PINCNTL57
L7
0x000C 0000
MCA[5]_AXR[0]
MCA[4]_AXR[2]
0x4814 08E4
PINCNTL58
L6
0x000C 0000
MCA[5]_AXR[1]
MCA[4]_AXR[3]
0x4814 08E8
PINCNTL59
U4
0x0004 0000
UART2_RXD
GP0[29]
0x4814 08EC
PINCNTL60
T2
0x0004 0000
TCLKIN
GP0[30]
0x4814 08F0
PINCNTL61
U3
0x000C 0000
UART2_TXD(M1)
GP0[31]
0x4814 08F4
PINCNTL62
W1
0x000C 0000
GP1[7](M1)
0x4814 08F8
PINCNTL63
W2
0x000E 0000
GP1[8](M1)
0x4814 08FC
PINCNTL64
V1
0x000C 0000
GP1[9](M1)
0x4814 0900
PINCNTL65
V2
0x000E 0000
0x4814 0904
PINCNTL66
–
0x000C 0000
Reserved. Do Not Program this Register.
0x1
0x2
0x4
0x8
0x10
0x20
0x40
0x80
GP0[27](M1)
(M0)
TIM7_IO
(M1)
GP0[28](M1)
GP1[10](M1)
0x4814 0908
PINCNTL67
–
0x000E 0000
Reserved. Do Not Program this Register.
0x4814 090C
PINCNTL68
AH6
0x000E 0000
DCAN0_TX
UART2_TXD(M2)
I2C[3]_SDA(M1)
GP1[0]
0x4814 0910
PINCNTL69
AG6
0x000E 0000
DCAN0_RX
UART2_RXD(M2)
I2C[3]_SCL(M1)
GP1[1]
0x4814 0914
PINCNTL70
AH5
0x000E 0000
UART0_RXD
0x4814 0918
PINCNTL71
AG5
0x000E 0000
UART0_TXD
0x4814 091C
PINCNTL72
AE6
0x000E 0000
UART0_CTS
UART4_RXD(M3)
DCAN1_TX
SPI[1]_SCS[3]
0x4814 0920
PINCNTL73
AF5
0x000E 0000
UART0_RTS
(M3)
DCAN1_RX
SPI[1]_SCS[2]
0x4814 0924
PINCNTL74
AH4
0x000E 0000
UART0_DCD
UART3_RXD
UART4_TXD
(M0)
SD0_SDCD
SD2_SDCD
SPI[0]_SCS[3]
I2C[2]_SCL
SPI[0]_SCS[2]
I2C[2]_SDA(M0)
(M0)
SD1_POW
GP1[2]
SD1_SDWP
GP1[3]
0x4814 0928
PINCNTL75
AG4
0x000E 0000
UART0_DSR
UART3_TXD(M0)
0x4814 092C
PINCNTL76
AG2
0x000E 0000
UART0_DTR
(M0)
0x4814 0930
PINCNTL77
AF4
0x000E 0000
UART0_RIN
UART3_RTS
0x4814 0934
PINCNTL78
AF24
0x000E 0000
I2C[1]_SCL
HDMI_SCL(M0)
0x4814 0938
PINCNTL79
AG24
0x000E 0000
I2C[1]_SDA
HDMI_SDA(M0)
0x4814 093C
PINCNTL80
AE5
0x0006 0000
SPI[0]_SCS[1]
SD1_SDCD
0x4814 0940
PINCNTL81
AD6
0x0006 0000
SPI[0]_SCS[0]
0x4814 0944
PINCNTL82
AC7
0x0006 0000
SPI[0]_SCLK
0x4814 0948
PINCNTL83
AF3
0x0006 0000
SPI[0]_D[1]
0x4814 094C
PINCNTL84
AE3
0x0006 0000
SPI[0]_D[0]
0x4814 0950
PINCNTL85
AD3
0x0006 0000
SPI[1]_SCS[0]
GP1[16](M1)
0x4814 0954
PINCNTL86
AC3
0x0006 0000
SPI[1]_SCLK
GP1[17](M1)
0x4814 0958
PINCNTL87
AA3
0x0006 0000
SPI[1]_D[1]
GP1[18](M1)
0x4814 095C
PINCNTL88
AA6
0x0006 0000
SPI[1]_D[0]
GP1[26](M1)
UART3_CTS
(M0)
UART1_TXD
(M0)
GP1[4]
(M0)
GP1[5]
UART1_RXD
SATA_ACT0_LED
EDMA_EVT1(M1)
TIM4_IO(M1)
GP1[6]
Device Configurations
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
163
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 4-13. PINCNTLx Registers MUXMODE Functions (continued)
HEX
ADDRESS
REGISTER
NAME
PIN
NO.
REGISTER
RESET
VALUE
MUXMODE[7:0] SETTINGS
0x4814 0960
PINCNTL89
U26
0x0005 0000
GPMC_D[0]
BTMODE[0]
0x4814 0964
PINCNTL90
Y28
0x0005 0000
GPMC_D[1]
BTMODE[1]
0x4814 0968
PINCNTL91
V27
0x0005 0000
GPMC_D[2]
BTMODE[2]
0x4814 096C
PINCNTL92
W27
0x0005 0000
GPMC_D[3]
BTMODE[3]
0x4814 0970
PINCNTL93
V26
0x0005 0000
GPMC_D[4]
BTMODE[4]
0x4814 0974
PINCNTL94
AA28
0x0005 0000
GPMC_D[5]
BTMODE[5]
0x4814 0978
PINCNTL95
U25
0x0005 0000
GPMC_D[6]
BTMODE[6]
0x4814 097C
PINCNTL96
V25
0x0005 0000
GPMC_D[7]
BTMODE[7]
0x4814 0980
PINCNTL97
Y27
0x0005 0000
GPMC_D[8]
BTMODE[8]
0x4814 0984
PINCNTL98
AB28
0x0005 0000
GPMC_D[9]
BTMODE[9]
0x4814 0988
PINCNTL99
Y26
0x0005 0000
GPMC_D[10]
BTMODE[10]
0x4814 098C
PINCNTL100
AA27
0x0005 0000
GPMC_D[11]
BTMODE[11]
0x4814 0990
PINCNTL101
U24
0x0005 0000
GPMC_D[12]
BTMODE[12]
0x4814 0994
PINCNTL102
U23
0x0005 0000
GPMC_D[13]
BTMODE[13]
0x4814 0998
PINCNTL103
V24
0x0005 0000
GPMC_D[14]
BTMODE[14]
0x4814 099C
PINCNTL104
Y25
0x0005 0000
GPMC_D[15]
BTMODE[15]
0x4814 09A0
PINCNTL105
AD27
0x0004 0000
GPMC_A[16]
GP2[5](M0)
0x4814 09A4
PINCNTL106
V23
0x0004 0000
GPMC_A[17]
GP2[6](M0)
0x1
0x2
0x4
0x8
0x10
0x20
0x40
0x80
0x4814 09A8
PINCNTL107
AE28
0x0004 0000
GPMC_A[18]
TIM2_IO(M2)
GP1[13](M0)
0x4814 09AC
PINCNTL108
AC27
0x0004 0000
GPMC_A[19]
TIM3_IO(M2)
GP1[14](M0)
0x4814 09B0
PINCNTL109
AD28
0x0006 0000
0x4814 09B4
PINCNTL110
AC28
0x0004 0000
GPMC_A[21]
SPI[2]_D[0]
SPI[2]_D[1](M0)
(M0)
SPI[2]_SCS[1]
GP1[15](M0)
(M0)
(M0)
GP1[16](M0)
GPMC_A[20]
0x4814 09B8
PINCNTL111
AB27
0x0006 0000
GPMC_A[22](M0)
0x4814 09BC
PINCNTL112
AA26
0x0004 0000
(M0)
GPMC_A[23]
0x4814 09C0
PINCNTL113
L25
0x0006 0000
SD2_DAT[7]
GPMC_A[24]
GPMC_A[20]
UART2_RXD
0x4814 09C4
PINCNTL114
N23
0x0006 0000
SD2_DAT[6]
GPMC_A[25](M0)
GPMC_A[21](M1)
UART2_TXD(M3)
0x4814 09C8
PINCNTL115
P22
0x0006 0000
SD2_DAT[5]
(M0)
(M1)
0x4814 09CC
PINCNTL116
R24
0x0006 0000
SD2_DAT[4]
GPMC_A[27]
0x4814 09D0
PINCNTL117
J28
0x0006 0000
SD2_DAT[3]
GPMC_A[1](M1)
GP2[5](M1)
0x4814 09D4
PINCNTL118
K27
0x0006 0000
SD2_DAT[2]_SDRW
GPMC_A[2](M1)
GP2[6](M1)
0x4814 09D8
PINCNTL119
M24
0x0006 0000
SD2_DAT[1]_SDIRQ
GPMC_A[3]
(M1)
GP1[13](M1)
0x4814 09DC
PINCNTL120
L26
0x0006 0000
SD2_DAT[0]
GPMC_A[4]
(M1)
GP1[14](M1)
0x4814 09E0
PINCNTL121
M23
0x0006 0000
SD2_CLK
0x4814 09E4
PINCNTL122
T28
0x0006 0000
GPMC_CS[0]
0x4814 09E8
PINCNTL123
K28
0x0006 0000
GPMC_CS[1]
164
HDMI_CEC(M0)
(M0)
SPI[2]_SCLK
(M0)
GPMC_A[26]
(M0)
HDMI_HPDET
(M1)
(M0)
GPMC_A[23]
GP1[17](M0)
(M2)
GP1[18](M0)
TIM5_IO
GP1[19]
(M3)
GPMC_A[22]
(M1)
TIM4_IO(M2)
GP1[20]
(M2)
GP1[21]
(M2)
GP1[22]
TIM6_IO
GPMC_CS[7]
(M1)
EDMA_EVT0
TIM7_IO
GP1[15](M1)
GP1[23]
GPMC_A[25](M1)
Device Configurations
GP1[24]
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 4-13. PINCNTLx Registers MUXMODE Functions (continued)
HEX
ADDRESS
REGISTER
NAME
PIN
NO.
REGISTER
RESET
VALUE
MUXMODE[7:0] SETTINGS
0x4814 09EC
PINCNTL124
M25
0x0006 0000
GPMC_CS[2]
GPMC_A[24]
0x4814 09F0
PINCNTL125
P26
0x0006 0000
GPMC_CS[3]
VIN[1]B_CLK
0x4814 09F4
PINCNTL126
P25
0x0006 0000
GPMC_CS[4]
SD2_CMD
0x4814 09F8
PINCNTL127
R26
0x0006 0000
GPMC_CLK
GPMC_CS[5]
0x4814 09FC
PINCNTL128
M26
0x0006 0000
GPMC_ADV_ALE
GPMC_CS[6]
0x4814 0A00
PINCNTL129
T27
0x0006 0000
GPMC_OE_RE
0x4814 0A04
PINCNTL130
U28
0x0006 0000
GPMC_WE
0x4814 0A08
PINCNTL131
U27
0x0004 0000
GPMC_BE[0]_CLE
GPMC_A[25](M2)
0x4814 0A0C
PINCNTL132
V28
0x0004 0000
GPMC_BE[1]
0x4814 0A10
PINCNTL133
W28
0x0006 0000
GPMC_WAIT[0]
0x4814 0A14
PINCNTL134
AE17
0x0004 0000
VIN[0]B_CLK
0x1
0x2
0x4
0x8
0x10
0x20
0x40
0x80
GP1[25]
(M1)
SPI[2]_SCS[0]
GP1[26](M0)
GP1[8](M0)
GPMC_WAIT[1]
CLKOUT1
(M3)
GP1[27]
(M3)
TIM5_IO
GP1[28]
EDMA_EVT2(M0)
TIM6_IO(M3)
GP1[29]
GPMC_A[24](M2)
EDMA_EVT1(M0)
TIM7_IO(M3)
GP1[30]
GPMC_A[26](M2)
EDMA_EVT0(M0)
(M0)
EDMA_EVT3
TIM4_IO
GP1[31]
CLKOUT0
GP1[9](M0)
0x4814 0A18
PINCNTL135
AE21
0x000E 0000
VIN[0]A_DE
VIN[0]B_HSYNC
UART5_TXD
0x4814 0A1C
PINCNTL136
AA20
0x000E 0000
VIN[0]A_FLD(M0)
VIN[0]B_VSYNC
UART5_RXD(M1)
0x4814 0A20
PINCNTL137
AB20
0x000C 0000
VIN[0]A_CLK
0x4814 0A24
PINCNTL138
AC20
0x000E 0000
VIN[0]A_HSYNC
UART5_RTS
(M1)
GP2[3]
UART5_CTS(M1)
GP2[4]
(M0)
(M1)
(M1)
I2C[2]_SDA
GP2[0]
I2C[2]_SCL(M3)
GP2[1]
GP2[2](M1)
0x4814 0A28
PINCNTL139
AD20
0x000E 0000
VIN[0]A_VSYNC
0x4814 0A2C
PINCNTL140
AF9
0x000C 0000
VIN[0]A_D[0]
GP1[11](M1)
0x4814 0A30
PINCNTL141
AB11
0x000C 0000
VIN[0]A_D[1]
GP1[12](M1)
0x4814 0A34
PINCNTL142
AC9
0x000C 0000
VIN[0]A_D[2]
GP2[7]
0x4814 0A38
PINCNTL143
AE12
0x000C 0000
VIN[0]A_D[3]
GP2[8]
0x4814 0A3C
PINCNTL144
AH8
0x000C 0000
VIN[0]A_D[4]
GP2[9]
0x4814 0A40
PINCNTL145
AG16
0x000C 0000
VIN[0]A_D[5]
GP2[10]
0x4814 0A44
PINCNTL146
AH16
0x000C 0000
VIN[0]A_D[6]
GP2[11]
0x4814 0A48
PINCNTL147
AA11
0x000C 0000
VIN[0]A_D[7]
GP2[12]
0x4814 0A4C
PINCNTL148
AB15
0x000C 0000
VIN[0]A_D[8]_BD[0]
GP2[13]
0x4814 0A50
PINCNTL149
AG9
0x000C 0000
VIN[0]A_D[9]_BD[1]
GP2[14]
0x4814 0A54
PINCNTL150
AH9
0x000C 0000
VIN[0]A_D[10]_BD[2]
0x4814 0A58
PINCNTL151
AH17
0x000C 0000
VIN[0]A_D[11]_BD[3]
CAM_WE(M1)
GP2[16]
0x4814 0A5C
PINCNTL152
AG17
0x0004 0000
VIN[0]A_D[12]_BD[4]
CLKOUT1
GP2[17]
0x4814 0A60
PINCNTL153
AF17
0x000C 0000
VIN[0]A_D[13]_BD[5]
CAM_RESET
GP2[18]
0x4814 0A64
PINCNTL154
AC12
0x000C 0000
VIN[0]A_D[14]_BD[6]
CAM_STROBE
GP2[19]
0x4814 0A68
PINCNTL155
AC14
0x000C 0000
VIN[0]A_D[15]_BD[7]
CAM_SHUTTER
GP2[20]
0x4814 0A6C
PINCNTL156
AA21
0x000E 0000
VIN[0]A_D[16]
CAM_D[8]
I2C[2]_SCL(M1)
GP0[10](M0)
0x4814 0A70
PINCNTL157
AB21
0x000C 0000
VIN[0]A_D[17]
CAM_D[9]
GP2[15]
EMAC[1]_RMRXER(M
GP0[11](M0)
1)
Device Configurations
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
165
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 4-13. PINCNTLx Registers MUXMODE Functions (continued)
HEX
ADDRESS
0x4814 0A74
REGISTER
NAME
PIN
NO.
REGISTER
RESET
VALUE
PINCNTL158
AF20
0x000E 0000
MUXMODE[7:0] SETTINGS
0x1
VIN[0]A_D[18]
0x2
0x4
CAM_D[10]
0x8
EMAC[1]_RMRXD[1]
0x10
(
0x20
0x40
0x80
(M2)
GP0[12](M0)
I2C[3]_SDA(M2)
GP0[13](M0)
SPI[3]_SCS[0]
GP0[14](M0)
SPI[3]_SCLK(M0)
GP0[15](M0)
SPI[3]_D[1](M0)
GP0[16](M0)
SPI[3]_D[0](M0)
GP0[17](M0)
I2C[3]_SCL
M1)
0x4814 0A78
PINCNTL159
AF21
0x000E 0000
VIN[0]A_D[19]
CAM_D[11]
EMAC[1]_RMRXD[0](
M1)
0x4814 0A7C
PINCNTL160
AC17
0x000C 0000
VIN[0]A_D[20]
CAM_D[12]
EMAC[1]_RMCRSDV(
M1)
0x4814 0A80
PINCNTL161
AE18
0x0004 0000
VIN[0]A_D[21]
CAM_D[13]
EMAC[1]_RMTXD[0](
M1)
0x4814 0A84
PINCNTL162
AC21
0x0004 0000
VIN[0]A_D[22]
CAM_D[14]
EMAC[1]_RMTXD[1](
M1)
0x4814 0A88
PINCNTL163
AC16
0x0004 0000
VIN[0]A_D[23]
CAM_D[15]
EMAC[1]_RMTXEN(M1
)
0x4814 0A8C
PINCNTL164
AB17
0x0006 0000
VIN[0]A_DE(M1)
CAM_D[7]
GP0[18](M0)
0x4814 0A90
PINCNTL165
AC15
0x0006 0000
VIN[0]B_DE
CAM_D[6]
GP0[19](M0)
0x4814 0A94
PINCNTL166
AC22
0x0006 0000
VIN[0]A_FLD
CAM_D[5]
GP0[20](M0)
0x4814 0A98
PINCNTL167
AD17
0x0006 0000
VIN[0]B_FLD
CAM_D[4]
GP0[21](M0)
0x4814 0A9C
PINCNTL168
AD18
0x0006 0000
VOUT[1]_G_Y_YC[1]
CAM_D[3]
GPMC_A[5](M1)
UART4_RXD(M0)
GP0[22](M0)
0x4814 0AA0
PINCNTL169
AC18
0x0004 0000
VOUT[1]_G_Y_YC[0]
CAM_D[2]
GPMC_A[6]
(M1)
UART4_TXD
(M0)
GP0[23](M0)
0x4814 0AA4
PINCNTL170
AC19
0x0004 0000
VOUT[1]_R_CR[1]
CAM_D[1]
GPMC_A[7]
(M1)
UART4_CTS
(M0)
GP0[24](M0)
(M1)
0x4814 0AA8
PINCNTL171
AA22
0x0004 0000
VOUT[1]_R_CR[0]
CAM_D[0]
GPMC_A[8](M1)
UART4_RTS(M0)
GP0[25](M0)
0x4814 0AAC
PINCNTL172
AE23
0x0004 0000
VOUT[1]_B_CB_C[1]
CAM_HS
GPMC_A[9](M1)
UART2_RXD(M0)
GP0[26](M0)
0x4814 0AB0
PINCNTL173
AD23
0x0006 0000
VOUT[1]_B_CB_C[0]
CAM_VS
(M0)
GP0[27](M0)
0x4814 0AB4
PINCNTL174
AB23
0x0004 0000
VOUT[1]_FLD
CAM_FLD
(M1)
UART2_TXD
(M1)
GPMC_A[11]
UART2_CTS
GP0[28](M0)
CAM_PCLK
GPMC_A[12](M1)
UART2_RTS
GP2[2](M0)
SPI[3]_SCLK(M2)
0x4814 0AB8
PINCNTL175
AF18
0x0004 0000
VOUT[0]_FLD(M1)
0x4814 0ABC
PINCNTL176
AD12
0x000C 0000
VOUT[0]_CLK
0x4814 0AC0
PINCNTL177
AC11
0x000C 0000
VOUT[0]_HSYNC
0x4814 0AC4
PINCNTL178
AB13
0x000C 0000
VOUT[0]_VSYNC
0x4814 0AC8
PINCNTL179
AA10
0x000C 0000
VOUT[0]_AVID
VOUT[0]_FLD(M0)
0x4814 0ACC
PINCNTL180
AG7
0x000C 0000
Reset by GCR
Only
VOUT[0]_B_CB_C[2]
EMU2
0x4814 0AD0
PINCNTL181
AE15
0x000C 0000
VOUT[0]_B_CB_C[3]
0x4814 0AD4
PINCNTL182
AD11
0x000C 0000
VOUT[0]_B_CB_C[4]
0x4814 0AD8
PINCNTL183
AD15
0x000C 0000
VOUT[0]_B_CB_C[5]
0x4814 0ADC
PINCNTL184
AC10
0x000C 0000
VOUT[0]_B_CB_C[6]
0x4814 0AE0
PINCNTL185
AB10
0x000C 0000
VOUT[0]_B_CB_C[7]
0x4814 0AE4
PINCNTL186
AF15
0x000C 0000
VOUT[0]_B_CB_C[8]
166
GPMC_A[10]
CAM_WE
(M0)
TIM7_IO(M1)
GP2[21]
GP2[22]
GP2[23]
Device Configurations
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 4-13. PINCNTLx Registers MUXMODE Functions (continued)
HEX
ADDRESS
REGISTER
NAME
PIN
NO.
REGISTER
RESET
VALUE
MUXMODE[7:0] SETTINGS
0x4814 0AE8
PINCNTL187
AG15
0x000C 0000
VOUT[0]_B_CB_C[9]
0x4814 0AEC
PINCNTL188
AH7
0x000C 0000
Reset by GCR
Only
VOUT[0]_G_Y_YC[2]
0x4814 0AF0
PINCNTL189
AH15
0x000C 0000
VOUT[0]_G_Y_YC[3]
0x4814 0AF4
PINCNTL190
AB8
0x000C 0000
VOUT[0]_G_Y_YC[4]
0x1
0x4814 0AF8
PINCNTL191
AB12
0x000C 0000
VOUT[0]_G_Y_YC[5]
0x4814 0AFC
PINCNTL192
AA8
0x000C 0000
VOUT[0]_G_Y_YC[6]
0x48140B00
PINCNTL193
AD14
0x000C 0000
VOUT[0]_G_Y_YC[7]
0x48140B04
PINCNTL194
AE14
0x000C 0000
VOUT[0]_G_Y_YC[8]
0x48140B08
PINCNTL195
AF14
0x000C 0000
VOUT[0]_G_Y_YC[9]
0x48140B0C
PINCNTL196
AD9
0x000C 0000
Reset by GCR
Only
VOUT[0]_R_CR[2]
0x4814 0B10
PINCNTL197
AB9
0x000C 0000
VOUT[0]_R_CR[3]
0x4814 0B14
PINCNTL198
AA9
0x000C 0000
VOUT[0]_R_CR[4]
0x2
0x4
0x8
0x10
0x20
0x40
EMU3
0x80
GP2[24]
GP2[25]
EMU4
GP2[26]
GP2[27]
0x4814 0B18
PINCNTL199
AF8
0x000C 0000
VOUT[0]_R_CR[5]
0x4814 0B1C
PINCNTL200
AF6
0x000C 0000
VOUT[0]_R_CR[6]
0x4814 0B20
PINCNTL201
AF12
0x000C 0000
VOUT[0]_R_CR[7]
0x4814 0B24
PINCNTL202
AE8
0x000C 0000
VOUT[0]_R_CR[8]
0x4814 0B28
PINCNTL203
AC13
0x000C 0000
VOUT[0]_R_CR[9]
0x4814 0B2C
PINCNTL204
AE24
0x0004 0000
VOUT[1]_CLK
EMAC[1]_MTCLK
VIN[1]A_HSYNC
0x4814 0B30
PINCNTL205
AC24
0x0004 0000
VOUT[1]_HSYNC
EMAC[1]_MCOL
VIN[1]A_VSYNC
0x4814 0B34
PINCNTL206
AA23
0x0004 0000
VOUT[1]_VSYNC
EMAC[1]_MCRS
VIN[1]A_FLD
0x4814 0B38
PINCNTL207
Y22
0x0004 0000
VOUT[1]_AVID
EMAC[1]_MRXER
VIN[1]A_CLK
0x4814 0B3C
PINCNTL208
AH25
0x0004 0000
VOUT[1]_B_CB_C[3]
EMAC[1]_MRCLK
0x4814 0B40
PINCNTL209
AG25
0x0004 0000
VOUT[1]_B_CB_C[4]
EMAC[1]_MRXD[0]
0x4814 0B44
PINCNTL210
AF25
0x0004 0000
VOUT[1]_B_CB_C[5]
0x4814 0B48
PINCNTL211
AD25
0x0004 0000
GP2[28]
VIN[1]A_DE
SPI[3]_D[1](M2)
UART3_RTS(M1)
SPI[3]_D[0](M2)
UART3_CTS(M1)
GP2[29]
GP2[30]
VIN[1]A_D[0]
UART4_CTS
(M2)
GP3[0]
VIN[1]A_D[1]
UART4_RXD(M2)
GP3[1]
EMAC[1]_MRXD[1]
VIN[1]A_D[2]
(M2)
GP3[2]
VOUT[1]_B_CB_C[6]
EMAC[1]_MRXD[2]
VIN[1]A_D[3]
(M1)
UART3_RXD
GP3[3]
UART3_TXD(M1)
GP3[4]
0x48140B4C
PINCNTL212
AC25
0x0004 0000
VOUT[1]_B_CB_C[7]
EMAC[1]_MRXD[3]
VIN[1]A_D[4]
0x4814 0B50
PINCNTL213
AH26
0x0004 0000
VOUT[1]_B_CB_C[8]
EMAC[1]_MRXD[4]
VIN[1]A_D[5]
0x4814 0B54
PINCNTL214
AA24
0x0004 0000
VOUT[1]_B_CB_C[9]
EMAC[1]_MRXD[5]
VIN[1]A_D[6]
UART4_TXD
I2C[3]_SCL
(M1)
GP2[31]
UART4_RTS
(M2)
TIM6_IO
(M3)
GP3[5]
(M3)
GP3[6]
I2C[3]_SDA
0x4814 0B58
PINCNTL215
Y23
0x0004 0000
VOUT[1]_G_Y_YC[3]
EMAC[1]_MRXD[6]
VIN[1]A_D[8]
GP3[7]
0x4814 0B5C
PINCNTL216
W22
0x0004 0000
VOUT[1]_G_Y_YC[4]
EMAC[1]_MRXD[7]
VIN[1]A_D[9]
GP3[8]
0x4814 0B60
PINCNTL217
AG26
0x0004 0000
VOUT[1]_G_Y_YC[5]
EMAC[1]_MRXDV
VIN[1]A_D[10]
GP3[9]
0x4814 0B64
PINCNTL218
AH27
0x0004 0000
VOUT[1]_G_Y_YC[6]
EMAC[1]_GMTCLK
VIN[1]A_D[11]
GP3[10]
0x4814 0B68
PINCNTL219
AF26
0x0004 0000
VOUT[1]_G_Y_YC[7]
EMAC[1]_MTXD[0]
VIN[1]A_D[12]
GP3[11]
0x4814 0B6C
PINCNTL220
AE26
0x0004 0000
VOUT[1]_G_Y_YC[8]
EMAC[1]_MTXD[1]
VIN[1]A_D[13]
GP3[12]
Device Configurations
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
167
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 4-13. PINCNTLx Registers MUXMODE Functions (continued)
HEX
ADDRESS
REGISTER
NAME
PIN
NO.
REGISTER
RESET
VALUE
0x4814 0B70
PINCNTL221
AD26
0x0004 0000
VOUT[1]_G_Y_YC[9]
EMAC[1]_MTXD[2]
VIN[1]A_D[14]
0x4814 0B74
PINCNTL222
AG27
0x0004 0000
VOUT[1]_R_CR[4]
EMAC[1]_MTXD[3]
VIN[1]A_D[15]
SPI[3]_SCS[1]
GP3[14]
0x4814 0B78
PINCNTL223
AC26
0x0004 0000
VOUT[1]_R_CR[5]
EMAC[1]_MTXD[4]
VIN[1]A_D[16]
SPI[3]_SCLK(M1)
GP3[15]
0x4814 0B7C
PINCNTL224
AA25
0x0004 0000
VOUT[1]_R_CR[6]
EMAC[1]_MTXD[5]
VIN[1]A_D[17]
0x4814 0B80
PINCNTL225
V22
0x0004 0000
VOUT[1]_R_CR[7]
EMAC[1]_MTXD[6]
VIN[1]A_D[18]
SPI[3]_D[0]
0x4814 0B84
PINCNTL226
W23
0x0004 0000
VOUT[1]_R_CR[8]
EMAC[1]_MTXD[7]
VIN[1]A_D[19]
UART5_RXD(M2)
0x4814 0B88
PINCNTL227
Y24
0x0004 0000
VOUT[1]_R_CR[9]
EMAC[1]_MTXEN
VIN[1]A_D[20]
(M2)
0x4814 0B8C
PINCNTL228
AF27
0x0006 0000
VOUT[1]_G_Y_YC[2]
(M1)
GPMC_A[13]
VIN[1]A_D[21]
0x4814 0B90
PINCNTL229
AG28
0x0006 0000
VOUT[1]_R_CR[3]
GPMC_A[14](M1)
0x4814 0B94
PINCNTL230
AE27
0x0004 0000
VOUT[1]_R_CR[2]
GPMC_A[15](M1)
0x4814 0B98
PINCNTL231
AF28
0x0006 0000
VOUT[1]_B_CB_C[2]
0x4814 0B9C
PINCNTL232
J27
0x0004 0000
EMAC_RMREFCLK
0x4814 0BA0
PINCNTL233
H28
0x000E 0000
MDCLK
0x4814 0BA4
PINCNTL234
P24
0x000E 0000
MDIO
0x4814 0BA8
PINCNTL235
L24
0x000C 0000
EMAC[0]_MTCLK/
EMAC[0]_RGRXC
VIN[1]B_D[0]
0x4814 0BAC
PINCNTL236
L23
0x000C 0000
EMAC[0]_MCOL/
EMAC[0]_RGRXCTL
VIN[1]B_D[1]
EMAC[0]_RMRXD[0]
GP3[24]
0x4814 0BB0
PINCNTL237
R25
0x000C 0000
EMAC[0]_MCRS/
EMAC[0]_RGRXD[2]
VIN[1]B_D[2]
EMAC[0]_RMRXD[1]
GP3[25]
0x4814 0BB4
PINCNTL238
J26
0x000C 0000
EMAC[0]_MRXER/
EMAC[0]_RGTXCTL
VIN[1]B_D[3]
EMAC[0]_RMRXER
GP3[26]
0x4814 0BB8
PINCNTL239
H27
0x000C 0000
EMAC[0]_MRCLK/
EMAC[0]_RGTXC
VIN[1]B_D[4]
EMAC[0]_RMCRSDV
0x4814 0BBC
PINCNTL240
G28
0x0004 0000
EMAC[0]_MRXD[0]/
EMAC[0]_RGTXD[0]
VIN[1]B_D[5]
EMAC[0]_RMTXD[0]
GP3[28]
0x4814 0BC0
PINCNTL241
P23
0x0004 0000
EMAC[0]_MRXD[1]/
EMAC[0]_RGRXD[0]
VIN[1]B_D[6]
EMAC[0]_RMTXD[1]
GP3[29]
0x4814 0BC4
PINCNTL242
R23
0x0004 0000
EMAC[0]_MRXD[2]/
EMAC[0]_RGRXD[1]
VIN[1]B_D[7]
EMAC[0]_RMTXEN
GP3[30](M0)
0x4814 0BC8
PINCNTL243
J25
0x0004 0000
EMAC[0]_MRXD[3]/
EMAC[1]_RGRXCTL
0x4814 0BCC
PINCNTL244
T23
0x0004 0000
0x4814 0BD0
PINCNTL245
H26
0x4814 0BD4
PINCNTL246
0x4814 0BD8
PINCNTL247
168
MUXMODE[7:0] SETTINGS
0x1
0x2
GPMC_A[0]
(M1)
0x4
0x8
0x10
0x20
0x40
0x80
GP3[13]
(M1)
GP3[16]
(M1)
GP3[17]
SPI[3]_D[1]
UART5_TXD
GP3[18]
GP3[19]
HDMI_SCL
SPI[2]_SCS[2]
I2C[2]_SCL
(M2)
GP3[20]
VIN[1]A_D[22]
HDMI_SDA(M1)
SPI[2]_SCLK(M1)
I2C[2]_SDA(M2)
GP3[21]
VIN[1]A_D[23]
HDMI_HPDET(M1)
SPI[2]_D[1](M1)
(M1)
VIN[1]A_D[7]
(M1)
HDMI_CEC
GP3[22]
(M1)
GP3[30](M1)
SPI[2]_D[0]
(M3)
GP1[10](M0)
TIM2_IO
GP1[11](M0)
GP1[12](M0)
SPI[3]_SCS[3]
GPMC_A[27](M1)
SPI[3]_SCS[2]
GPMC_A[26](M1)
GPMC_A[0](M0)
UART5_RXD(M0)
EMAC[0]_MRXD[4]/
EMAC[0]_RGRXD[3]
GPMC_A[1](M0)
UART5_TXD(M0)
0x0004 0000
EMAC[0]_MRXD[5]/
EMAC[0]_RGTXD[3]
GPMC_A[2](M0)
UART5_CTS(M0)
F28
0x0004 0000
EMAC[0]_MRXD[6]/
EMAC[0]_RGTXD[2]
GPMC_A[3](M0)
UART5_RTS(M0)
G27
0x0004 0000
EMAC[0]_MRXD[7]/
EMAC[0]_RGTXD[1]
GPMC_A[4](M0)
SPI[2]_SCS[3]
Device Configurations
(M3)
I2C[2]_SDA
GP3[23]
GP3[27]
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 4-13. PINCNTLx Registers MUXMODE Functions (continued)
HEX
ADDRESS
REGISTER
NAME
PIN
NO.
REGISTER
RESET
VALUE
MUXMODE[7:0] SETTINGS
0x4814 0BDC
PINCNTL248
K22
0x0004 0000
EMAC[0]_MRXDV/
EMAC[1]_RGRXD[1]
GPMC_A[5]
0x4814 0BE0
PINCNTL249
K23
0x0004 0000
EMAC[0]_GMTCLK/
EMAC[1]_RGRXC
GPMC_A[6](M0)
SPI[2]_D[1](M2)
0x4814 0BE4
PINCNTL250
J24
0x0004 0000
EMAC[0]_MTXD[0]/
EMAC[1]_RGRXD[3]
GPMC_A[7](M0)
SPI[2]_D[0](M2)
0x4814 0BE8
PINCNTL251
H25
0x0004 0000
EMAC[0]_MTXD[1]/
EMAC[1]_RGTXD[1]
GPMC_A[8](M0)
UART4_RXD(M1)
0x4814 0BEC
PINCNTL252
H22
0x0004 0000
EMAC[0]_MTXD[2]/
EMAC[1]_RGTXCTL
EMAC[1]_RMRXD[0](M0)
GPMC_A[9](M0)
UART4_TXD(M1)
0x4814 0BF0
PINCNTL253
H23
0x0004 0000
EMAC[0]_MTXD[3]/
EMAC[1]_RGTXD[0]
EMAC[1]_RMRXD[1](M0)
GPMC_A[10](M0)
UART4_CTS(M1)
0x4814 0BF4
PINCNTL254
G23
0x0004 0000
EMAC[0]_MTXD[4]/
EMAC[1]_RGTXD[2]
EMAC[1]_RMRXER
GPMC_A[11](M0)
UART4_RTS(M1)
0x4814 0BF8
PINCNTL255
F27
0x0004 0000
EMAC[0]_MTXD[5]/
EMAC[1]_RGTXC
EMAC[1]_RMCRSDV(M0)
GPMC_A[12](M0)
UART1_RXD(M1)
0x4814 0BFC
PINCNTL256
J22
0x0004 0000
EMAC[0]_MTXD[6]/
EMAC[1]_RGRXD[0]
EMAC[1]_RMTXD[0](M0)
GPMC_A[13](M0)
UART1_TXD(M1)
0x4814 0C00
PINCNTL257
H24
0x0004 0000
EMAC[0]_MTXD[7]/
EMAC[1]_RGTXD[3]
EMAC[1]_RMTXD[1](M0)
GPMC_A[14](M0)
UART1_CTS
0x4814 0C04
PINCNTL258
J23
0x0004 0000
EMAC[0]_MTXEN/
EMAC[1]_RGRXD[2]
EMAC[1]_RMTXEN(M0)
GPMC_A[15](M0)
UART1_RTS
0x4814 0C08
PINCNTL259
J7
0x0004 0000
CLKIN32
0x4814 0C0C
PINCNTL260
J5
0x000E 0000
RESET
0x4814 0C10
PINCNTL261
H7
0x000E 0000
NMI
0x4814 0C14
PINCNTL262
K6
0x0005 0000
RSTOUT_WD_OUT
0x4814 0C18
PINCNTL263
AC4
0x000D 0000
I2C[0]_SCL
0x4814 0C1C
PINCNTL264
AB6
0x000D 0000
I2C[0]_SDA
0x4814 0C20
PINCNTL265
–
Undetermined
Reserved. Do Not Program this Register.
0x4814 0C24
PINCNTL266
–
Undetermined
Reserved. Do Not Program this Register.
0x4814 0C28
PINCNTL267
–
Undetermined
Reserved. Do Not Program this Register.
0x4814 0C2C
PINCNTL268
–
Undetermined
Reserved. Do Not Program this Register.
0x4814 0C30
PINCNTL269
–
Undetermined
Reserved. Do Not Program this Register.
0x4814 0C34
PINCNTL270
AF11
0x000C 0000
USB0_DRVVBUS
0x1
0x2
0x4
0x8
CLKOUT0
0x10
(M0)
0x20
0x40
0x80
(M2)
SPI[2]_SCLK
TIM3_IO(M3)
GP3[31]
GP0[7]
Device Configurations
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
169
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
4.4
www.ti.com
Handling Unused Pins
When device signal pins are unused in the system, they can be left unconnected unless otherwise noted
in the Terminal Functions tables (see Section 3.2). For unused input pins, the internal pull resistor should
be enabled, or an external pull resistor should be used, to prevent floating inputs. Unless otherwise noted,
all supply pins must always be connected to the correct voltage, even when their associated signal pins
are unused.
4.5
4.5.1
DeBugging Considerations
Pullup/Pulldown Resistors
Proper board design should ensure that input pins to the TMS320DM814x DaVinci™ Digital Media
Processsors device always be at a valid logic level and not floating. This may be achieved via
pullup/pulldown resistors. The device features internal pullup (IPU) and internal pulldown (IPD) resistors
on most pins to eliminate the need, unless otherwise noted, for external pullup/pulldown resistors.
An external pullup/pulldown resistor needs to be used in the following situations:
• Boot Configuration Pins: If the pin is both routed out and 3-stated (not driven), an external
pullup/pulldown resistor is strongly recommended, even if the IPU/IPD matches the desired
value/state.
• Other Input Pins: If the IPU/IPD does not match the desired value/state, use an external
pullup/pulldown resistor to pull the signal to the opposite rail.
For the boot configuration pins (listed in Table 3-1, Boot Configuration Terminal Functions), if they are
both routed out and 3-stated (not driven), it is strongly recommended that an external pullup/pulldown
resistor be implemented. Although, internal pullup/pulldown resistors exist on these pins and they may
match the desired configuration value, providing external connectivity can help ensure that valid logic
levels are latched on these device boot configuration pins. In addition, applying external pullup/pulldown
resistors on the boot and configuration pins adds convenience to the user in debugging and flexibility in
switching operating modes.
Tips for choosing an external pullup/pulldown resistor:
• Consider the total amount of current that may pass through the pullup or pulldown resistor. Make sure
to include the leakage currents of all the devices connected to the net, as well as any internal pullup or
pulldown resistors.
• Decide a target value for the net. For a pulldown resistor, this should be below the lowest VIL level of
all inputs connected to the net. For a pullup resistor, this should be above the highest VIH level of all
inputs on the net. A reasonable choice would be to target the VOL or VOH levels for the logic family of
the limiting device; which, by definition, have margin to the VIL and VIH levels.
• Select a pullup/pulldown resistor with the largest possible value; but, which can still ensure that the net
will reach the target pulled value when maximum current from all devices on the net is flowing through
the resistor. The current to be considered includes leakage current plus, any other internal and
external pullup/pulldown resistors on the net.
• For bidirectional nets, there is an additional consideration which sets a lower limit on the resistance
value of the external resistor. Verify that the resistance is small enough that the weakest output buffer
can drive the net to the opposite logic level (including margin).
• Remember to include tolerances when selecting the resistor value.
• For pullup resistors, also remember to include tolerances on the DVDD rail.
For most systems, a 1-kΩ resistor can be used to oppose the IPU/IPD while meeting the above criteria.
Users should confirm this resistor value is correct for their specific application.
For most systems, a 20-kΩ resistor can be used to compliment the IPU/IPD on the boot and configuration
pins while meeting the above criteria. Users should confirm this resistor value is correct for their specific
application.
170
Device Configurations
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
For most systems, a 20-kΩ resistor can also be used as an external PU/PD on the pins that have
IPUs/IPDs disabled and require an external PU/PD resistor while still meeting the above criteria. Users
should confirm this resistor value is correct for their specific application.
For more detailed information on input current (II), and the low-/high-level input voltages (VIL and VIH) for
the device, see Section 6.4, Electrical Characteristics Over Recommended Ranges of Supply Voltage and
Operating Temperature.
For the internal pullup/pulldown resistors for all device pins, see the peripheral/system-specific terminal
functions table.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Configurations
171
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
5 System Interconnect
The device’s various processors, subsystems, and peripherals are interconnected through a switch fabric
architecture. The switch fabric is composed of an L3 and L4 interconnect, a switched central resource
(SCR), and multiple bridges (for an overview, see Figure 5-1). Not all Initiators in the switch fabric are
connected to all Target peripherals. The supported initiator and target connections are designated by a "X"
in Table 5-1, Target/Initiator Connectivity.
For more detailed information on the device System Interconnect Architecture, see the TMS320DM814x
DaVinci Digital Media Processors Technical Reference Manual (Literature Number: SPRUGZ8).
EDMATC RD 0/1
EDMATC WR 0/1
Note1
DSP MDMA
L3F
Initiators
L3F
Initiators
ARM Cortex
A8
EDMATC RD 2/3
EDMATC WR 2/3
HDVICP2
HDVPSS (2 I/F)
ISS
SGX530
64b
128b
1 I/F
System
MMU
128b
9 I/F
PCIe
MEDIACTL
128b
1 I/F
2 I/F
L3S Initiators
USB2.0 (2 I/F)
DSP CFG
EMAC SW
SATA
DAP
64b
128b
4 I/F
L3F
Initiators
32b
32b
7 I/F
4 I/F
L3F/L3Mid
Interconnect
200 MHz (Note 2)
2 I/F
128b
2 I/F
128b
DMM
DDR0
DDR1
5 I/F
128b
64b
L3F
Targets
DSP SDMA
HDVICP2 SL2
L3S Interconnect
100 MHz (Note 2)
11 I/F
32b
L3F
Targets
L3F
Targets
PCIe
MEDIACTL
SGX530
OCMC SRAM
ISS
MMCSD 2
HDVICP2 CFG
EDMATC 0/1/2/3
EDMACC
DEBUGSS
8 I/F
2 I/F
2 I/F
32b
32b
32b
L3S Targets
L4F
Interconnect
MCASP 0/1 / 2 Data
MCBSP
GPMC
HDMI
USB
200 MHz
(Note 2)
11 I/F
L4S
Interconnect
100 MHz
(Note2)
58 I/F
32b
32b
L4S Targets
L4F Targets
MMU
UART 0/1/2/3/4/5
I2C 0/1/2/3
DMTimer 0/1/2/3/4/5/6/7/8
SPI 0/1/2/3
GPIO 0/1/2/3
MCASP 0/1/2 CFG
MMCSD 0 /1
ELM
RTC
WDT 0/1
Mailbox
Spinlock
HDVPSS
HDMIPHY
PLLSS
Control Module
PRCM
DCAN 0/1
OCPWP
SYNCTIMER32K
EMAC SW
SATA
MCASP 3/4/5 CFG
MCASP 3/4/5 DATA
Note 1 : TPTC 0/1 RD/WR transactions can optionally be routed through System MMU using chip control module
Note 2 : The frequencies specified are for 100% OPP
Figure 5-1. System Interconnect
172
System Interconnect
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 5-1. L3 Master/Slave Connectivity (1)
(1)
X = Connection exists.
S = Selectable path based on thirty-third address bit from control module register for System MMU accessible targets. Non-System
MMU accessible targets (such as, C674x SDMA) will always be direct mapped.
L4 HS Periph Port 0
X
X
Imaging SS
HDMI 1.3 Tx Audio
X
USB2.0 CFG
McBSP
X
OCMC RAM
McASP 0/1/2
X
EDMA TPCC
PCIe Gen2 Slave
X
EDMA TPTC0 - 3 CFG
C674x SDMA
X
L3 Registers
SGX530
X
L4 Std Periph Port 1
GPMC
X
L4 Std Periph Port 0
Media Controller
X
L4 HS Periph Port 1
HDVICP2 Hst
X
SD2
X
X
X
X
X
X
X
X
ARM M2 (64-bit)
C674x MDMA
HDVICP2 SL2
ARM M1 (128-bit)
EDMA DMM ELLA
EDMA DMM Tiler/Lisa1
EDMA DMM Tiler/Lisa0
MASTERS
System MMU
SLAVES
X
X
X
X
X
X
X
System MMU
X
X
X
X
X
C674x CFG
HDVICP2 VDMA
X
HDVPSS Mstr0
X
X
X
X
X
X
X
X
X
X
HDVPSS Mstr1
X
X
X
X
SGX530 BIF
X
X
X
X
X
X
X
X
X
SATA
X
X
EMAC SW
X
X
X
USB2.0 DMA
X
X
X
USB2.0 Queue Mgr
X
X
PCIe Gen2
X
X
X
Media Controller
X
X
X
DeBug Access Port (DAP)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
EDMA TPTC0 RD
S
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
EDMA TPTC0 WR
S
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
EDMA TPTC1 RD
S
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
EDMA TPTC1 WR
S
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
EDMA TPTC2 RD
X
EDMA TPTC2 WR
X
X
X
X
X
X
X
X
X
X
X
EDMA TPTC3 RD
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
EDMA TPTC3 WR
X
X
ISS
X
X
X
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
X
System Interconnect
173
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
The L4 interconnect is a non-blocking peripheral interconnect that provides low-latency access to a large
number of low-bandwidth, physically-dispersed target cores. The L4 can handle incoming traffic from up to
four initiators and can distribute those communication requests to and collect related responses from up to
63 targets.
The device provides two interfaces with L3 interconnect for high-speed peripheraland standard peripheral.
Table 5-2. L4 Peripheral Connectivity (1)
MASTERS
L4 PERIPHERALS
ARM CortexA8 M2 (64-bit)
EDMA
TPTC0
EDMA
TPTC1
EDMA
TPTC2
EDMA
TPTC3
C674x
CONFIG
System
MMU
PCIe
Port0
Port0
Port1
L4 Fast Peripherals Port 0/1
EMAC SW
Port0
Port1
Port0
Port1
Port0
SATA
Port0
Port1
Port0
Port1
Port0
McASP3 CFG
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
McASP4 CFG
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
McASP5 CFG
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
McASP3 DATA
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
McASP4 DATA
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
McASP5 DATA
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
Port1
L4 Slow Peripherals Port 0/1
I2C0
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
I2C1
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
I2C2
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
I2C3
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
SPI0
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
SPI1
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
SPI2
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
SPI3
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
UART0
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
UART1
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
UART2
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
UART3
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
UART4
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
UART5
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
Timer1
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
Timer2
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
Timer3
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
Timer4
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
Timer5
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
Timer6
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
Timer7
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
Timer8
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
GPIO0
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
GPIO1
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
MMC/SD0/SDIO
Port0
Port1
Port0
Port1
Port0
Port1
MMC/SD1/SDIO
Port0
Port1
Port0
Port1
Port0
Port1
MMC/SD2/SDIO
Port0
Port1
Port0
Port1
Port0
Port1
WDT0
Port0
Port1
Port0
Port1
Port0
Port1
RTC
Port0
Port1
Port0
Port1
Port0
Port1
(1)
174
X, Port0, Port1 = Connection exists.
System Interconnect
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 5-2. L4 Peripheral Connectivity(1) (continued)
MASTERS
L4 PERIPHERALS
ARM CortexA8 M2 (64-bit)
EDMA
TPTC0
EDMA
TPTC1
EDMA
TPTC2
EDMA
TPTC3
C674x
CONFIG
System
MMU
PCIe
System MMU
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
Mailbox
Port0
Port0
Port0
Spinlock
Port0
Port0
Port0
HDVPSS
Port0
PLLSS
Port0
Port1
Control/Top Regs
(Control Module)
Port0
Port1
PRCM
Port0
Port1
ELM
Port0
Port1
HDMIPHY
Port0
DCAN0
Port0
Port1
Port0
Port1
Port0
Port1
DCAN1
Port0
Port1
Port0
Port1
Port0
Port1
OCPWP
Port0
McASP0 CFG
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
McASP1 CFG
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
McASP2 CFG
Port0
Port1
Port0
Port1
Port0
Port0
Port0
Port1
SYNCTIMER32K
Port0
Port1
Port0
Port1
Port0
Port1
Port0
Port1
Port0
Port1
Port1
Port0
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Port1
System Interconnect
175
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
6 Device Operating Conditions
6.1
Absolute Maximum Ratings
Supply voltage ranges
(Steady State):
(1) (2)
Core (CVDD, CVDD_ARM, CVDD_DSP, CVDD_HDVICP)
-0.3 V to 1.5 V
I/O, 1.8 V (DVDD_M, DVDD_DDR[0], DVDD_DDR[1], VDDA_1P8, VDDA_ARMPLL_1P8,
VDDA_DSPPLL_1P8, VDDA_VID0PLL_1P8, VDDA_VID1PLL_1P8,
VDDA_AUDIOPLL_1P8, VDDA_DDRPLL_1P8, VDDA_L3PLL_1P8, VDDA_PCIE_1P8,
VDDA_SATA_1P8, VDDA_HDMI_1P8, VDDA_USB0_1P8, VDDA_USB1_1P8,
VDDA_VDAC_1P8)
-0.3 V to 2.1 V
I/O 3.3 V (DVDD, DVDD_GPMC, DVDD_GPMCB, DVDD_SD, DVDD_C)
-0.3 V to 4.0 V
DDR Reference Voltage (VREFSSTL_DDR[0], VREFSSTL_DDR[1])
-0.3 V to 1.1 V
V I/O, 1.5-V pins (Steady State)
-0.3 V to
DVDD_DDR[x] + 0.3
V
V I/O, 1.8-V pins (Steady State)
-0.3 V to DVDD +
0.3 V
-0.3 V to DVDD_x +
0.3 V
V I/O, 3.3-V pins (Steady State)
-0.3 V to DVDD +
0.3 V
-0.3 V to DVDD_x +
0.3 V
Input and Output voltage
ranges:
Commercial Temperature
Operating junction
temperature range, TJ:
0°C to 90°C
Industrial
-40°C to 90°C
Extended
-40°C to 105°C
Storage temperature
range, Tstg:
Latch-up Performance:
-55°C to 150°C
I-test: Silicon Revision 3.0, All I/O pins (3)
±100 mA
I-test: Silicon Revision 2.1, All I/O pins (3)
±70 mA
Over-Voltage Test, All Supply pins
Electrostatic Discharge
(ESD) Performance:
(1)
(2)
(3)
(4)
(5)
(6)
176
(4)
1.5xVddmax V
ESD-HBM (Human Body Model) (5)
±1000 V
ESD-CDM (Charged-Device Model) (6)
±250 V
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to their associated VSS or VSSA_x.
Pins stressed per JEDEC JESD78 at 90°C (Class II) and passed with specified I/O pin injection current and clamp voltage of 1.5 times
maximum recommended I/O voltage and negative 0.5 times maximum recommended I/O voltage.
Supplies stressed per JEDEC JESD78 at 90°C (Class II) and passed specified voltage injection.
Level listed is the passing level per ANSI/ESDA/JEDEC JS-001. JEDEC document JEP155 states that 500-V HBM allows safe
manufacturing with a standard ESD control process, and manufacturing with less than 500-V HBM is possible if necessary precautions
are taken. Pins listed as 1000 V may actually have higher performance.
Level listed is the passing level per EIA-JEDEC JESD22-C101E. JEDEC document JEP157 states that 250-V CDM allows safe
manufacturing with a standard ESD control process, and manufacturing with less than 250-V CDM is possible if necessary precautions
are taken. Pins listed as 250 V may actually have higher performance.
Device Operating Conditions
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
6.2
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Recommended Operating Conditions
PARAMETER
Supply voltage, Core (Scalable)
DVFS only, No AVS
CVDD
Supply voltage, Core ARM
(Scalable)
DVFS only, No AVS
CVDD_ARM
Supply voltage, Core, DSP
(Scalable)
DVFS only, No AVS
CVDD_DSP
Supply voltage, Core, HDVICP2
(Scalable)
DVFS only, No AVS
CVDD_HDVICP
MIN
NOM
MAX
166% OPP
1.28
1.35
1.42
120% OPP
1.14
1.20
1.26
100% OPP
1.05
1.10
1.16
166% OPP
1.28
1.35
1.42
120% OPP
1.14
1.20
1.26
100% OPP
1.05
1.10
1.16
166% OPP
1.28
1.35
1.42
120% OPP
1.14
1.20
1.26
100% OPP
1.05
1.10
1.16
166% OPP
1.28
1.35
1.42
120% OPP
1.14
1.20
1.26
100% OPP
1.05
1.10
1.16
DVDD
Supply voltage, I/O, standard
pins (1)
3.3 V
3.14
3.3
3.47
1.8 V
1.71
1.8
1.89
DVDD_GPMC
Supply voltage, I/O, GPMC pin
group
3.3 V
3.14
3.3
3.47
1.8 V
1.71
1.8
1.89
DVDD_GPMCB
Supply voltage, I/O, GPMCB pin
group
3.3 V
3.14
3.3
3.47
1.8 V
1.71
1.8
1.89
Supply voltage, I/O, SD pin group
3.3 V
3.14
3.3
3.47
1.8 V
1.71
1.8
1.89
3.3 V
3.14
3.3
3.47
1.8 V
1.71
1.8
1.89
DVDD_SD
DVDD_C
Supply voltage, I/O, C pin group
UNIT
V
V
V
V
V
V
V
V
V
DVDD_M
Supply voltage, I/O, M pin group
1.8 V
1.71
1.8
1.89
DVDD_DDR[0]
DVDD_DDR[1]
Supply voltage, I/O, DDR[0] and
DDR[1]
DDR2
1.71
1.8
1.89
DDR3 mode
1.43
1.5
1.58
3.14
3.3
3.47
V
1.71
1.8
1.89
V
VDDA_USB_3P Supply voltage, I/O, Analog, USB 3.3 V
3
VDDA_1P8
VDDA_x_1P8
Supply Voltage, I/O, Analog, (VDDA_1P8,
VDDA_ARMPLL_1P8, VDDA_DSPPLL_1P8,
VDDA_VID0PLL_1P8, VDDA_VID1PLL_1P8,
VDDA_AUDIOPLL_1P8, VDDA_DDRPLL_1P8,
VDDA_L3PLL_1P8, VDDA_PCIE_1P8, VDDA_SATA_1P8,
VDDA_HDMI_1P8, VDDA_USB0_1P8, VDDA_USB1_1P8,
VDDA_VDAC_1P8)
Note: HDMI, USB0/1, and VDAC relative to their respective
VSSA.
VSS
Supply Ground (VSS, VSSA_HDMI, VSSA_USB,
VSSA_VDAC, VSSA_DEVOSC (2), VSSA_AUXOSC (2))
VREFSSTL_DDR[x]
IO Reference Voltage, (VREFSSTL_DDR[0],
VREFSSTL_DDR[1])
USBx_VBUSIN
USBx VBUS Comparator Input
High-level input voltage, LVCMOS (JTAG[TCK] pins), 3.3
V (1)
VIH
V
0.49 *
DVDD_DDR[
x]
0.50 *
DVDD_DDR[x]
0.51 *
DVDD_DDR[x]
V
4.75
5
5.25
V
V
High-level input voltage, JTAG[TCK], 3.3 V
2.15
V
High-level input voltage, JTAG[TCK], 1.8 V
1.45
V
0.7DVDD
V
0.65DVDDx
V
High-level input voltage, LVCMOS (1), 1.8 V
(2)
V
2
High-level input voltage, I2C (I2C[0] and I2C[1])
(1)
0
V
LVCMOS pins are all I/O pins powered by DVDD, DVDD_GPMC, DVDD_GPMCB, DVDD_SD, DVDD_C supplies except for I2C[0] and
I2C[1] pins.
When using the internal Oscillators, the oscillator grounds (VSSA_DEVOSC, VSSA_AUXOSC) must be kept separate from other
grounds and connected directly to the crystal load capacitor ground.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Operating Conditions
177
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Recommended Operating Conditions (continued)
PARAMETER
MIN
NOM
MAX
Low-level input voltage, LVCMOS (1), 3.3 V
Low-level input voltage, JTAG[TCK]
VIL
High-level output current
IOH
Low-level output current
IOL
0.45
V
V
0.35DVDDx
V
6 mA I/O buffers
-6
mA
DDR[0], DDR[1] buffers
@ 50-Ω impedance
setting
-8
mA
6 mA I/O buffers
6
mA
DDR[0], DDR[1] buffers
@ 50-Ω impedance
setting
8
mA
VID
Differential input voltage (SERDES_CLKN/P), [AC coupled]
tt
Transition time, 10% - 90%, All inputs (unless otherwise
specified in the Electrical Data/Timing sections of each
peripheral)
TJ
Operating junction temperature
range (4)
(3)
V
0.3DVDDx
Low-level input voltage, I2C (I2C[0] and I2C[1])
Low-level input voltage, LVCMOS (1), 1.8 V
UNIT
0.8
0.250
Commercial
Temperature (default)
2.0
V
0.25P or 10 (3)
ns
90
°C
0
Industrial
-40
90
°C
Extended
-40
105
°C
Whichever is smaller. P = the period of the applied signal. Maintaining transition times as fast as possible is recommended to improve
noise immunity on input signals.
For more detailed information on estimating junction temps within systems, see the IC Package Thermal Metrics Application Report
(Literature Number: SPRA953).
(4)
6.3
Power-On Hours (POH)
The POH information in Table 6-1 is provided solely for convenience and does not extend or modify the warranty
provided under TI’s standard terms and conditions for TI Semiconductor Products. To avoid significant device
degradation, the device POH must be limited to those shown in Table 6-1.
Table 6-1. Power-On Hour Limits
Operating Condition
Nominal CVDD Voltage (V)
Junction
Temperature (Tj)
Lifetime POH (1)
100% OPP
1.1
-40 to 105 °C
100K
120% OPP
1.2
-40 to 105 °C
100K
166% OPP
1.35
-40 to 105 °C
49K
(1)
POH represent device operation under the specified nominal conditions continuously for the duration of the calculated lifetime.
Logic functions and parameter values are not ensured out of the range specified in Section 6.2,
Recommended Operating Conditions.
The above notations cannot be deemed a warranty or deemed to extend or modify the warranty under TI’s
standard terms and conditions for semiconductor products.
178
Device Operating Conditions
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
6.4
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Electrical Characteristics Over Recommended Ranges of Supply Voltage and
Operating Temperature (Unless Otherwise Noted)
TEST CONDITIONS (1)
PARAMETER
VOH
VOL
MIN
TYP
2.8
VDD_USB_3P
3
High speed: USB_DM and
USB_DP
360
440
UNIT
V
mV
High-level output voltage,
LVCMOS (2) (3.3-V I/O)
3.3 V, DVDDx = MIN, IOH =
MAX
2.4
V
High-level output voltage,
LVCMOS (2) (1.8-V I/O)
1.8 V, DVDDx = MIN, IOH =
MAX
1.26
V
Low/Full speed: USB_DM
and USB_DP
0.0
0.3
V
High speed: USB_DM and
USB_DP
-10
10
mV
Low-level output voltage,
LVCMOS (2) (3.3-V I/O)
3.3 V, DVDDx = MAX, IOL =
MAX
0.4
V
Low-level output voltage,
LVCMOS (2) (1.8-V I/O)
1.8 V, DVDDx = MAX, IOL =
MAX
0.4
V
Low-level output voltage,
I2C (I2C[0], I2C[1])
1.8/3.3 V, IOL = 4mA
0.4
V
1.5
V
20
µA
LDOs (applies to all
LDOCAP_x pins)
Input current, LVCMOS (2),
3.3 V mode
Input current, LVCMOS (2),
1.8 V mode
II (3)
MAX
Low/Full speed: USB_DM
and USB_DP
Input current, I2C (I2C[0],
I2C[1])
0 < VI < DVDDx, 3.3 V pull
disabled
-20
0 < VI < DVDDx, 3.3 V
pulldown enabled (4)
20
100
300
µA
0 < VI < DVDDx, 3.3 V
pullup enabled (4)
-20
-100
-300
µA
5
µA
0 < VI < DVDDx, 1.8 V pull
disabled
-5
0 < VI < DVDDx, 1.8 V
pulldown enabled (4)
50
100
200
µA
0 < VI < DVDDx, 1.8 V
pullup enabled (4)
-50
-100
-200
µA
3.3 V mode
-20
20
µA
1.8 V mode
-5
5
µA
3.3 V mode, pull enabled
-300
300
µA
3.3 V mode, pull disabled
-20
20
µA
1.8 V mode, pull enabled
-200
200
µA
1.8 V mode, pull disabled
-5
IOZ (5)
I/O Off-state output current
ICDD
Core (CVDD) supply current (scalable)
see note
(6)
mA
ARM Core Current
(Scalable)
see note
(6)
ICVDD_ARM
mA
DSP Core Current
(Scalable)
see note
(6)
ICVDD_DSP
mA
HDVICP2 Core Current
(Scalable)
see note
(6)
ICVDD_HDVICP
mA
(1)
(2)
(3)
(4)
(5)
(6)
5
µA
For test conditions shown as MIN, MAX, or TYP, use the appropriate value specified in the recommended operating conditions table.
LVCMOS pins are all I/O pins powered by DVDD, DVDD_GPMC, DVDD_GPMCB, DVDD_SD, DVDD_C supplies except for I2C[0] and
I2C[1] pins.
II applies to input-only pins and bi-directional pins. For input-only pins, II indicates the input leakage current. For bi-directional pins, II
indicates the input leakage current and off-state (Hi-Z) output leakage current.
Applies only to pins with an internal pullup (IPU) or pulldown (IPD) resistor.
IOZ applies to output-only pins, indicating off-state (Hi-Z) output leakage current.
The actual current draw varies across manufacturing processes and is highly application-dependent. For more details on core and I/O
activity, as well as information relevant to board power supply design, see the TMS320DM814x/AM387x Power Estimation Spreadsheet
Application Report (Literature Number: SPRABO3). To determine the worst-case power consumption values, use the
TMS320DM814x/AM387x Power Estimation Spreadsheet Application Report.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Device Operating Conditions
179
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Electrical Characteristics Over Recommended Ranges of Supply Voltage and Operating Temperature
(Unless Otherwise Noted) (continued)
TEST CONDITIONS (1)
PARAMETER
IDDD
MIN
TYP
MAX
UNIT
3.3-V I/O (DVDD,
DVDD_GPMC,
DVDD_GPMCB,
DVDD_SD, DVDD_C,
VDDA_USB_3P3) supply
current
see note
(6)
mA
1.8-V I/O (DVDD,
DVDD_GPMC,
DVDD_GPMCB,
DVDD_SD, DVDD_C
DVDD_M, DVDD_DDR[0],
DVDD_DDR[1] [for DDR2],
VDDA_x_1P8) supply
current
see note
(6)
mA
1.5-V I/O (DVDD_DDR[0],
DVDD_DDR[1] [for DDR3
SDRAM]) supply current
see note
(6)
mA
CI
Input capacitance
LVCMOS (2)
12
pF
Co
Output capacitance
LVCMOS (2)
12
pF
180
Device Operating Conditions
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
7 Power, Reset, Clocking, and Interrupts
7.1
Power, Reset and Clock Management (PRCM) Module
The PRCM module is the centralized management module for the power, reset, and clock control signals
of the device. The PRCM interfaces with all the components on the device for power, clock, and reset
management through power-control signals. The PRCM module inTiming Requirements for
AUD_CLKINxtegrates enhanced features to allow the device to adapt energy consumption dynamically,
according to changing application and performance requirements. The innovative hardware architecture
allows a substantial reduction in leakage current.
The PRCM module is composed of two main entities:
• Power reset manager (PRM): Handles the power, reset, wake-up management, and system clock
source control (oscillator)
• Clock manager (CM): Handles the clock generation, distribution, and management.
For more details on the PRCM, see the Power, Reset, and Clock Management (PRCM) Module chapter of
the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
7.2
Power
7.2.1
Voltage and Power Domains
Every Module within the device belongs to a Core Logic Voltage Domain, Memory Voltage Domain, and a
Power Domain (see Table 7-1).
Table 7-1. Voltage and Power Domains
CORE LOGIC
VOLTAGE DOMAIN
MEMORY VOLTAGE
DOMAIN
ARM_L
ARM_M
CORE_L
CORE_M
POWER
DOMAIN
ARM Cortex-A8 Subsystem
ALWAYS ON
GFX
7.2.1.1
MODULES
DCAN0/1, DMM, EDMA, ELM, DDR0/1, EMAC Switch,
GPIO Banks 0/1/2/3,GPMC, I2C0/1/2/3, IPC,
MCASP0/1/2/3/4/5, MCBSP, OCMC SRAM, PCIE,
PRCM, RTC, SATA, SD/MMC0/1/2, SPI01/2/3,
Timer1/2/3/4/5/6/7/8, UART0/1/2/3/4/5, USB0/1,
WDT0, System Interconnect, JTAG, Media Controller,
ISS
SGX530
HDVPSS
HDVPSS, HDMI, SD-DAC
C674x DSP and L2 SRAM
DSP_L
DSP_M
DSP
HDVICP_L
HDVICP_M
HDVICP
HDVICP2
Core Logic Voltage Domains
The device contains four Core Logic Voltage Domains. These domains define groups of Modules that
share the same supply voltage for their core logic. Each Core Logic Voltage Domain is powered by a
dedicated supply voltage rail. Table 7-2 shows the mapping between the Core Logic Voltage Domains and
their associated supply pins.
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
181
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 7-2. Core Logic Voltage Domains and Supply Pin Associations
CORE LOGIC
VOLTAGE DOMAIN
SUPPLY PIN NAME
ARM_L
CVDD_ARM
CORE_L
CVDD
DSP_L
CVDD_DSP
HDVICP_L
CVDD_HDVICP
Note: A regulated supply voltage must be supplied to each Core Logic Voltage Domain at all times,
regardless of the Core Logic Power Domain states.
7.2.1.2
Memory Voltage Domains
The SRAM within each Device Module is assigned to one of four Memory Voltage Domains. The voltage
of each Memory Voltage Domain is independently controlled by internal LDO regulators, which are
supplied by the VDDA_1P8 pins.
The voltage level output by each of these LDO regulators is controlled through software by programming
the RAMLDO_CTRLx registers in the Control Module. The Memory Voltage Domain voltage must be
programmed based on the Core Logic Voltage Domain voltage for that domain (that is, the corresponding
Core Logic Voltage Domain for the ARM_M Voltage Domain is ARM_C, and so on). Table 7-3 shows the
Memory Voltage Domain voltage requirements.
Table 7-3. Memory Voltage Domain LDO Requirements
7.2.1.3
CORE LOGIC VOLTAGE
DOMAIN VOLTAGE (V)
MEMORY VOLTAGE DOMAIN
VOLTAGE (V)
0.83 – 1.20
1.20
Power Domains
The device contains six Power Domains which supply power to both the Core Logic and SRAM within their
associated modules. Each Power Domain, except for the ALWAYS ON domain, has an internal power
switch that can completely remove power from that domain. All power switches are turned "OFF" by
default after reset, and software can individually turn them "ON/OFF" via Control Module registers.
Note: All Modules within a Power Domain are unavailable when the domain is powered "OFF". For
instructions on powering "ON/OFF" the Power domains, see the Power, Reset, and Clock Management
(PRCM) Module chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference
Manual (Literature Number: SPRUGZ8).
7.2.2
SmartReflex [Not Supported]
The device contains SmartReflex modules that help to minimize power consumption on the Core Logic
Voltage Domains by using external variable-voltage power supplies. Based on the device process,
temperature, and desired performance, the SmartReflex modules advise the host processor to raise or
lower the supply voltage to each domain for minimal power consumption.
The communication link between the host processor and the external regulators is a system-level decision
and can be accomplished using GPIOs, I2C, SPI, or other methods. The following sections briefly
describe the two major techniques employed by SmartReflex: Dynamic Voltage Frequency Scaling
(DVFS) and Adaptive Voltage Scaling (AVS).
182
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
7.2.2.1
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Dynamic Voltage Frequency Scaling (DVFS)
Each device Core Logic Voltage Domain can be run independently at one of several Operating
Performance Points (OPPs). An OPP for a specific Core Logic Voltage Domain is defined by: (1)
maximum frequencies of operation for Modules within the Domain and (2) an associated supply voltage
range. Trading off power versus performance, OPPs with lower maximum frequencies also have lower
voltage ranges for power savings.
The OPP for a domain can be changed in real-time without requiring a reset. This feature is called
Dynamic Voltage Frequency Scaling (DVFS). Table 7-4 contains a list of voltage ranges and maximum
module frequencies for the OPPs of each Core Logic Voltage Domain.
Table 7-4. Device Operating Points (OPPs)
CORE LOGIC VOLTAGE DOMAINS
(1)
(2)
ARM
DSP
HDVICP
CORE
OPP
Cortex A8
(MHz)
DSP
(MHz)
HDVICP2
(MHz)
HDVPSS
(MHz)
SGX
(MHz)
ISS
(MHz)
Media Ctlr.
(MHz)
L3/L4,
Core
(MHz)
DDR
(MHz) (1)
100%
(1.1 V)
600
500
266
200
200
400
200
200
400
120%
(1.2 V)
720
600
306
200
250
400
200
220
400
166%
(CYE1)
(1.35 V)
1000
700
750 (2)
410
220
280
480
240
220
533
166%
(CYE2)
(1.35 V)
1000
750
450
220
280
560
280
220
533
All DDR access must be suspended prior to changing the DDR frequency of operation.
Only DM814x SR3.0 devices support a DSP Frequency of 750-MHz. For more details on device silicon revisions, see Figure 9-1, Device
Nomenclature.
Although the OPP for each Core Logic Voltage Domain is independently selectable, not all combinations
of OPPs are supported. Table 7-5 marks the supported ARM, DSP, and HDVICP2 OPPs for a given
CORE OPP.
Table 7-5. Supported OPP Combinations (1) (2)
ARM
CORE
OPP166
OPP166
X
OPP120
X
OPP100
(1)
(2)
OPP120
DSP
OPP100
OPP166
OPP120
HDVICP2
OPP100
X
X
X
X
X
OPP166
OPP120
OPP100
X
X
X
X
X
X
X
X
"X" denotes supported combinations.
The maximum voltage differences between CVDD and any other CVDD_x voltage domain must be < 150 mV.
7.2.2.2
Adaptive Voltage Scaling [Not Supported]
As mentioned in Section 7.2.2.1, Dynamic Voltage Frequency Scaling (DVFS) above, every OPP has an
associated voltage range. Based on the silicon process, temperature, and chosen OPP, the SmartReflex
modules guide software in adjusting the Core Logic Voltage Domain supply voltages within these ranges.
This technique is called Adaptive Voltage Scaling (AVS). AVS occurs continuously and in real-time,
helping to minimize power consumption in response to changing operating conditions.
7.2.3
Memory Power Management
To reduce SRAM leakage, many SRAM blocks can be switched from ACTIVE mode to SHUTDOWN
mode. When SRAM is put in SHUTDOWN mode, the voltage supplied to it is automatically removed and
all data in that SRAM is lost.
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
183
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
All SRAM located in a switchable power domain (all domains except ALWAYS_ON) automatically enters
SHUTDOWN mode whenever its associated power domain goes into the "OFF" state. The SRAM returns
to the ACTIVE state when the corresponding Power Domain returns to the "ON" state.
In addition, the following SRAM within the ALWAYS_ON Power Domain can also be independently put
into SHUTDOWN by programming the x_MEM_PWRDN registers in the Control Module:
• Media Controller SRAM
• OCMC SRAM
For detailed instructions on powering up/down the various device SRAM, see the Control Module chapter
of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature
Number: SPRUGZ8).
7.2.4
SERDES_CLKP and SERDES_CLKN LDO
The SERDES_CLKP and SERDES_CLKN input buffers are powered by an internal LDO which is
programmed through the REFCLK_LJCBLDO_CTRL register in the Control Module.
For more information on programming the SERDES_CLKP and SERDES_CLKN LDO, see PCI Express
(PCIe) Module and Serial ATA (SATA) Controller chapters of the TMS320DM814x DaVinci Digital Media
Processors Technical Reference Manual (Literature Number: SPRUGZ8).
7.2.5
Dual Voltage I/Os
The device supports dual voltages on some of its I/Os. These I/Os are partitioned into the following
groups, and each group has its own dedicated supply pins: DVDD, DVDD_GPMC, DVDD_C, and
DVDD_SD. The supply voltage for each group can be independently powered with either 1.8 V or 3.3 V.
For the mapping between pins and power groups, see Section 3.2, Terminal Functions of the datasheet.
In addition, the I/O voltage on each DDR interface is independently selectable between either 1.5 V or 1.8
V to support various DDR device types. The I/O supplies for each DDR interface are separate and isolated
to allow populating different memory types on each interface.
7.2.6
I/O Power-Down Modes
On the device, there are power-down modes available for the following PHYs:
• Video DAC
• DDR
• USB
• HDMI
• PCIE
• SATA
When a PHY controller is in a power domain that is to be turned "OFF", software must configure the
corresponding PHY into power-down mode, prior to putting the power domain in the "OFF" state.
184
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
7.2.7
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Standby Mode
The device supports Low-Power Standby Mode as described below.
Standby Mode is defined as a state in which:
• All switchable power domains are in "OFF" state
• The ARM Cortex-A8 is executing an IDLE loop at its lowest frequency of operation
• All functional blocks not needed for a given application are clock gated
For detailed instructions on entering and exiting from Standby Mode see the Power, Reset, and Clock
Management (PRCM) Module chapter of the TMS320DM814x DaVinci Digital Media Processors Technical
Reference Manual (Literature Number: SPRUGZ8).
7.2.8
Supply Sequencing
The device power supplies are organized into four Supply Sequencing Groups:
1. All CVDD supplies (CVDD, CVDD_x)
2. All 1.5-/1.8-V DVDD_DDR[x] Supplies (1.5 V for DDR3, 1.8 V for DDR2)
3. All 1.8-V Supplies (DVDD_x, DVDD_M, VDDA_x_1P8, VDDA_1P8)
4. All 3.3-V Supplies (DVDD, DVDD_x, DVDD_C, VDDA_x_3P3)
To ensure proper device operation, a specific power-up and power-down sequence must be followed.
Some TI power-supply devices include features that facilitate these power sequencing requirements — for
example, TI’s TPS659113 integrated PMIC. For more information on TI power supplies and their features,
visit www.ti.com/processorpower.
For more detailed information on the actual power supply names and their descriptions, see Table 3-49,
Supply Voltages Terminal Functions.
7.2.8.1
Power-Up Sequence
For proper device operation, the following power-up sequence in Table 7-6 and must be followed.
Table 7-6. Power-Up Sequence Ramping Values
NO.
MIN
MAX
UNIT
1.8 V and DVDD_DDR[x] supplies stable to 3.3 V supplies
ramp start
0
ms
2
1.8 V supplies to 1.5-/1.8- V DVDD_DDR[x] supplies
0
(1)
ms
3
1.8 V supplies stable to CVDD, CVDD_x variable supplies
ramp start
0 (1)
ms
13
CVDD variable supply ramp start to CVDD_x variable
supplies ramp start
0
ms
4
All supplies valid to power-on-reset (POR high)
4 096
Master
Clocks
1
(1)
DESCRIPTION
The 1.8 V supplies must be ≥ 1.5-/1.8-V DVDD_DDR[x] supplies.
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
185
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
1.8 V Supplies
(DVDD, DVDD_x, DVDD_M, VDDA_x_1P8,
VDDA_1P8)
3.3 V Supplies
(DVDD, DVDD_x, DVDD_C, VDDA_x_3P3)
1.5 V/1.8 V DVDD_DDR[x]
CVDD
Figure 7-1. Power-Up Sequence
7.2.8.2
Power-Down Sequence
For proper device operation, the following power-down sequence in Table 7-7 and Figure 7-2 must be
followed. Ramping down all supplies at the same time is allowed, provided the requirements in Table 7-7
are met.
Table 7-7. Power-Down Sequence Ramping Values
NO.
(1)
(2)
186
DESCRIPTION
MIN
MAX
UNIT
8
CVDD, CVDD_x variable supply to 1.8 V supplies
See
(1)
See
(1)
9
1.5-/1.8-V DVDD_DDR[x] supplies to 1.8 V supplies
See
(1)
See
(1)
ms
10
3.3 V supplies to 1.8 V supplies
See
(2)
See
(2)
ms
14
CVDD_x variable supplies ramp-down start to CVDD
variable supply ramp-down start
0
ms
ms
The 1.5-/1.8-V DVDD_DDR[x] and CVDD, CVDD_x variable supplies can be powered down prior to or simultaneously with the 1.8-V
supplies.
The 3.3 V supplies must never be more than 2 V above the 1.8 V supplies (see Figure 7-3).
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
1.8 V Supplies
(DVDD, DVDD_x, DVDD_M, VDDA_x_1P8,
VDDA_1P8
3.3 V Supplies
(DVDD, DVDD_x, DVDD_C, VDDA_x_3P3)
Figure 7-2. Power-Down Sequence
Figure 7-3. 1.8 V Supplies Falling Before 3.3 V Supplies Delta
7.2.9
Power-Supply Decoupling
7.2.9.1
Analog and PLL
PLL and Analog supplies benefit from filters or ferrite beads to keep the noise from causing problems. The
minimum recommendation is a ferrite bead along with at least one capacitor on the device side of the
bead. An additional recommendation is to add one capacitor just before the bead to form a Pi filter. The
filter needs to be as close as possible to the device pin, with the device side capacitor being the most
important component to be close to the device pin. PLL pins close together can be combined on the same
supply, but analog pins should all have their own filters. PLL pins farther away from each other may need
their own filtered supply.
7.2.9.2
Digital
Recommended capacitors for power supply decoupling are all 0.1uF in the smallest body size that can be
used. Capacitors are more effective in the smallest physical size to limit lead inductance. For example,
0201 sized capacitors are better than 0402 sized capacitors, and so on. TI recommends using capacitors
no larger than 0402. Place at least one capacitor for every two power pins. For those power pins that have
only one pin, a capacitor is still required. Place one bulk (10 uF or larger) capacitor for every 10 or so
power pins as closely as possible to the chip. These larger caps do not need to be under the chip
footprint.
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
187
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Pay special attention not to put so much capacitance on the supply that it slows the start-up voltage ramp
enough to change the power sequencing order. Also be sure to verify that the main chip reset is low until
after all supplies are at their correct voltage and stable.
DDR peripheral related supply capacitor numbers are provided in Section 8.13, DDR2/DDR3 Memory
Controller.
188
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
7.3
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Reset
7.3.1
System-Level Reset Sources
The device has several types of system-level resets. Table 7-8 lists these reset types, along with the reset
initiator, and the effects of each reset on the device.
Table 7-8. System-Level Reset Types
TYPE
Power-on Reset (POR)
External Warm Reset
Emulation Warm Reset
INITIATOR
RESETS ALL
MODULES,
EXCLUDING EMAC
SWITCH,
EMULATION, PLL
AND CLOCK
CONFIG
RESETS EMAC
SWITCH
RESETS
EMULATION
PLL AND CLOCK
CONFIG
LATCHES
BOOT PINS
ASSERTS
RSTOUT_WD_OUT
PIN
POR pin
Yes
Yes
Yes
Yes
Yes
Optional (1) (2)
(3)
No
No
Yes
Optional (1) (2)
No
No
No
Optional (1)
RESET pin
Yes
Optional
On-Chip Emulation
Logic
Yes
Optional (3)
Watchdog Timer
Yes
Optional (3)
No
No
No
Yes
Software Global Cold Reset
Software
Yes
Optional (3)
Yes
Yes
No
Optional (1)
Software Global Warm Reset
Software
Yes
Optional (3)
No
No
No
Optional (1)
Test Reset
TRST pin
No
No
Yes
No
No
No
Watchdog Reset
(1)
(2)
(3)
RSTOUT_WD_OUT pin asserted only if BTMODE[11] was latched as "0" when coming out of reset.
While POR and/or RESET is asserted, the RSTOUT_WD_OUT pin is 3-stated and the internal pull resistor is disabled; therefore, an
external pullup/pulldown can be used to set the state of this pin (high/low) while POR and/or RESET is asserted. For more detailed
information on external PUs/PDs, see Section 4.5.1, Pullup/Pulldown Resistors.
EMAC Switch is NOT reset when the ISO_CONTROL bit in the RESET_ISO Control Module register is set to "1".
7.3.2
Power-on Reset (POR pin)
Power-on Reset (POR) is initiated by the POR pin and is used to reset the entire chip, including the Test
and Emulation logic, and the EMAC Switch. POR is also referred to as a cold reset since it is required to
be asserted when the device goes through a power-up cycle. However, a device power-up cycle is not
required to initiate a Power-on Reset.
The following sequence must be followed during a Power-on Reset:
1. Wait for the power supplies to reach normal operating conditions while keeping the POR pin asserted.
2. Wait for the input clock sources DEV_CLKIN, AUX_CLKIN, and SERDES_CLKN/P to be stable (if
used by the system) while keeping the POR pin asserted (low).
3. Once the power supplies and the input clock sources are stable, the POR pin must remain asserted
(low) [see Section 7.3.18, Reset Electrical Data/Timing]. Within the low period of the POR pin, the
following happens:
(a) All pins except Emulation pins enter a Hi-Z mode and the associated pulls, if applicable, will be
enabled.
(b) The PRCM asserts reset to all modules within the device.
(c) The PRCM begins propagating these clocks to the chip with the PLLs in BYPASS mode.
4. The POR pin may now be de-asserted (driven high). When the POR pin is de-asserted (high):
(a) The BTMODE[15:0] pins are latched.
(b) Reset to the ARM Cortex-A8 and Modules without a local processor is de-asserted.
(c) RSTOUT_WD_OUT is briefly asserted if BTMODE[11] was latched as "0".
(d) The clock, reset, and power-down state of each peripheral is determined by the default settings of
the PRCM.
(e) The ARM Cortex-A8 begins executing from the Boot ROM.
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
189
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
7.3.3
www.ti.com
External Warm Reset (RESET pin)
An external warm reset is activated by driving the RESET pin active-low. This resets everything in the
device, except for the Test and Emulation logic, and the EMAC Switch (optional). An emulator session
stays alive during warm reset.
The following sequence must be followed during a warm reset:
1. Power supplies and input clock sources should already be stable.
2. The RESET pin must be asserted (low)[see Section 7.3.18, Reset Electrical Data/Timing]. Within the
low period of the RESET pin, the following happens:
(a) All pins, except Test and Emulation pins, enter a Hi-Z mode and the associated pulls, if applicable,
will be enabled.
(b) The PRCM asserts reset to all modules within the device, except for the Test and Emulation logic,
EMAC Switch (optional), PLL, and Clock configuration.
3. The RESET pin may now be de-asserted (driven high). When the RESET pin is de-asserted (high):
(a) The BTMODE[15:0] pins are latched.
(b) Reset to the ARM Cortex-A8 and modules without a local processor is de-asserted, with the
exception of Test and Emulation logic, EMAC Switch (optional), PLL, and Clock configuration.
(c) RSTOUT_WD_OUT is asserted [see Section 7.3.18, Reset Electrical Data/Timing], if BTMODE[11]
was latched as "0".
(d) The clock, reset, and power-down state of each peripheral is determined by the default settings of
the PRCM.
(e) The ARM Cortex-A8 begins executing from the Boot ROM.
7.3.4
Emulation Warm Reset
An Emulation Warm Reset is activated by the on-chip Emulation Module and has the same effect and
requirements as an External Warm Reset (RESET), with the following exceptions:
• BTMODE[15:0] pins are not re-latched
• RSTOUT_WD_OUT is not 3-stated and is actively driven based on the value previously latched on the
BTMODE[11] pin.
The emulator initiates an Emulation Warm Reset via the ICEPICK module. To invoke the Emulation Warm
Reset via the ICEPICK module, the user can perform the following from the Code Composer Studio™ IDE
menu: Target -> Reset -> System Reset.
7.3.5
Watchdog Reset
A Watchdog Reset is initiated when the Watchdog Timer counter reaches zero and has the same effect
and requirements as an External Warm Reset (RESET pin), with the following exceptions:
• BTMODE[15:0] pins are not re-latched
• RSTOUT_WD_OUT is not 3-stated and is actively driven based on the value previously latched on the
BTMODE[11] pin.
In addition, a Watchdog Reset always results in RSTOUT_WD_OUT being asserted, regardless of
whether the BTMODE[11] pin was latched as "0" or "1".
7.3.6
Software Global Cold Reset
A Software Global Cold Reset is initiated under software control and has the same effect and
requirements as a POR Reset, with the following exceptions:
• BTMODE[15:0] pins are not re-latched and EMAC Switch (optional) is not reset
• RSTOUT_WD_OUT is not 3-stated and is actively driven based on the value previously latched on the
BTMODE[11] pin.
190
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Software initiates a Software Global Cold Reset by writing a "1" to the RST_GLOBAL_COLD_SW bit in
the PRM_RSTCTRL register in the PRCM.
For more detailed information on the PRM_RSTCTRL register, see the PRCM Registers section of the
Power, Reset, and Clock Management (PRCM) Module chapter of the TMS320DM814x DaVinci Digital
Media Processors Technical Reference Manual (Literature Number: SPRUGZ8).
7.3.7
Software Global Warm Reset
A Software Global Warm Reset is initiated under software control and has the same effect and
requirements as a External Warm Reset (RESET pin), with the following exceptions:
• BTMODE[15:0] pins are not re-latched
• RSTOUT_WD_OUT is not 3-stated and is actively driven based on the value previously latched on the
BTMODE[11] pin.
Software initiates a Software Global Warm Reset by writing a "1" to the RST_GLOBAL_WARM_SW bit in
the PRM_RSTCTRL register in the PRCM.
For more detailed information on the PRM_RSTCTRL register, see the PRCM Registers section of the
Power, Reset, and Clock Management (PRCM) Module chapter of the TMS320DM814x DaVinci Digital
Media Processors Technical Reference Manual (Literature Number: SPRUGZ8).
7.3.8
Test Reset (TRST pin)
A Test Reset is activated by the emulator asserting the TRST pin. The only effect a Test Reset has is to
reset the Test and Emulation Logic.
7.3.9
Local Reset
The Local Reset for various Modules within the device is controlled by programming the PRCM and/or the
Peripheral Module’s internal registers. Only the associated Module is reset when a Local Reset is
asserted, leaving the rest of the device unaffected.
For more details on Peripheral Local Resets, see the Reset Management section of the Power, Reset,
and Clock Management (PRCM) Module chapter of the TMS320DM814x DaVinci Digital Media
Processors Technical Reference Manual (Literature Number: SPRUGZ8).
7.3.10 Reset Priority
If any of the above reset sources occur simultaneously, the device only processes the highest-priority
reset request. The reset request priorities, from high-to-low, are as follows:
1. Power-on Reset (POR)
2. Test Reset (TRST)
3. External Warm Reset (RESET pin)
4. Emulation Warm Resets
5. Watchdog Reset
6. Software Global Cold/Warm Resets
7.3.11 Reset Status Register
The Reset Status Register (PRM_RSTST) contains information about the last reset that occurred in the
system. For more information on this register, see the Power, Reset, and Clock Management (PRCM)
Module chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual
(Literature Number: SPRUGZ8).
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
191
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
7.3.12 PCIE Reset Isolation
The device supports reset isolation for the PCI Express (PCIE) module. This means that the PCI Express
Subsystem can be reset without resetting the rest of the device.
When the devcie is a PCI Express Root Complex (RC), the PCIE Subsystem can be reset by software
through the PRCM. Software should ensure that there are no ongoing PCIE transactions before asserting
this reset by first taking the PCIE Subsystem into the IDLE state. After bringing the PCIE Subsystem out
of reset, bus enumeration should be performed again and should treat all Endpoints (EP) as if they had
just been connected.
When the device is a PCI Express Endpoint (EP), the PCIE Subsystem will generate an interrupt when an
in-band reset is received. Software should process this interrupt by putting the PCIE Subsystem in the
IDLE state and then asserting the PCIE local reset through the PRCM.
All device level resets mentioned in the previous sections, except Test Reset, will also reset the PCIE
Subsystem. Therefore, the PCIE peripheral should issue a Hot Reset to all downstream devices and reenumerate the bus upon coming out of reset.
For more detailed information on reset isolation procedures, see the PCIe Reset Isolation section of the
Power, Reset, and Clock Management (PRCM) Module chapter of the TMS320DM814x DaVinci Digital
Media Processors Technical Reference Manual (Literature Number: SPRUGZ8).
7.3.13 EMAC Switch Reset Isolation
The device supports reset isolation for the Ethernet Switch (EMAC Switch). This allows the device to
undergo all resets listed in Section 7.3.1, System-Level Reset Sources, with the exception of POR Reset,
without disrupting the Ethernet Switch or the traffic being routed through the switch during the reset
condition. The following reset types can optionally provide an EMAC Switch reset isolation by setting the
ISO_CONTROL bit in the RESET_ISO Control Module register to a "1":
• External Warm Reset
• Emulation Warm Reset
• Watchdog Reset
• Software Global Cold Reset
• Software Global Warm Reset
When one of above resets occurs and the Ethernet Switch (EMAC Switch) is programmed to be isolated:
• The switch function of the EMAC Switch and the PLL embedded in the SATA SERDES Module (which
provides the reference clocks to the EMAC Switch) will not be reset.
• Several Control Module registers are not reset. For more details, see the description of the
RESET_ISO register in the Control Module chapter of the TMS320DM814x DaVinci Digital Media
Processors Technical Reference Manual (Literature Number: SPRUGZ8).
• The pin multiplexing of some of the EMAC Switch pins is unaffected. For more details, see the
description of the RESET_ISO register in the Control Module chapter of the TMS320DM814x DaVinci
Digital Media Processors Technical Reference Manual (Literature Number: SPRUGZ8).
The EMAC Switch is always reset when:
• One of the above resets occurs and the Ethernet Switch is programmed to be “not isolated”
• A POR Reset occurs
192
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
7.3.14 RSTOUT_WD_OUT Pin
The RSTOUT_WD_OUT pin reflects device reset status and is de-asserted (high) when the device is out
reset. This output will always be asserted when a Watchdog Timer reset (Watchdog Reset) occurs. In
addition, this output is always 3-stated and the internal pull resistor is disabled on this pin while POR
and/or RESET is asserted; therefore, an external pullup/pulldown can be used to set the state of this pin
(high/low) while POR and/or RESET is asserted. For more detailed information on external PUs/PDs, see
Section 4.5.1, Pullup/Pulldown Resistors.
If the BTMODE[11] pin is latched as a "0" at the rising edge of POR or RESET, then RSTOUT_WD_OUT
is also asserted when any of the below resets occur:
• Power-On Reset (asserted after the BTMODE[11] pin is latched)
• External Warm Reset (asserted after the BTMODE[11] pin is latched)
• Emulation Warm Reset
• Software Global Cold/Warm Reset
The RSTOUT_WD_OUT pin remains asserted until the PRCM releases the host ARM Cortex-A8
processor for reset.
7.3.15 Effect of Reset on Emulation and Trace
The device Emulation and Trace Logic will only be reset by the following sources:
• Power-On Reset
• Software Global Cold Reset
• Test Reset
Other than these three reset types, none of the other resets will affect the Emulation and Trace Logic.
However, the multiplexing of the EMU[4:2] pins is reset by all system reset types except Test Reset.
7.3.16 Reset During Power Domain Switching
Each Power Domain has a dedicated Warm Reset and Cold Reset. Warm Reset for a Power Domain is
asserted under either of the following two conditions:
1. An External Warm Reset, Emulation Warm Reset, or Software Global Warm Reset occurs
2. When that Power Domain switches from the "ON" state to the "OFF" state
Cold Reset for a Power Domain is asserted under either of the following two conditions:
1. Power-On Reset or Software Global Cold Reset occurs
2. When that Power Domain switches from the "OFF" state to the "ON" state
7.3.17 Pin Behaviors at Reset
When any reset, other than Test Reset, (all described in Section 7.3.1, System-Level Reset Sources) is
asserted, all device I/O pins are reset into a Hi-Z state except for:
• Emulation Pins. These pins are only put into a Hi-Z state when Test Reset (TRST) is asserted.
• EMAC Switch Pins. These pins are always put into a Hi-Z state during Power-On Reset. However,
some EMAC Switch pins will not be put into a Hi-Z state during the other reset modes when the
ISO_CONTROL bit in the RESET_ISO register of the Control Module is programmed as a "1". For
more details, see the description of the RESET_ISO register in the Control Module chapter of the
TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
• RSTOUT_WD_OUT Pin during any reset types except for POR and RESET. For more detailed
information on RSTOUT_WD_OUT pin behavior, see Section 7.3.14, RSTOUT_WD_OUT Pin.
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
193
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
•
www.ti.com
DDR[0]/[1] Address/Control Pins (CLK, CLK, CKE, WE, CS[1]/[0], RAS, CAS, ODT[1]/[0], RST,
BA[2:0], A[14:0]). These pins are 3-stated during reset. However, these pins are then driven to the
same value as their internal pull resistor reset value when reset is released (For the direction of the
internal pull during reset, see the DDR[0]/[1] Terminal Functions tables in the Section 3.2.4,
DDR2/DDR3 Memory Controller of this document).
In addition, the PINCNTL registers, which control pin multiplexing, enabling the IPUs/IPDs, and enabling
the receiver, are reset to their default state. Again, enabling the EMAC Switch reset isolation prevents
some PINCNTL registers from being reset.
For details on EMAC Switch reset isolation, see the descriptions of the RESET_ISO register and the
PINCNTL registers in the Control Module chapter of the TMS320DM814x DaVinci Digital Media
Processors Technical Reference Manual (Literature Number: SPRUGZ8).
Internal pull-up/down (IPU/IPD) resistors are enabled during and immediately after reset as described in
Section 3.2, Terminal Functions of this document.
NOTE
Upon coming out of reset, the ARM Cortex-A8 starts executing code from the internal Boot
ROM. The Boot ROM code modifies the PINCNTLx registers to configure the associated
pins for the chosen primary and backup Bootmodes. For more details on the Boot ROM
effects on pin multiplexing, see the ROM Code Memory and Peripheral Booting and Control
Module chapters of the TMS320DM814x DaVinci Digital Media Processors Technical
Reference Manual (Literature Number: SPRUGZ8).
7.3.18 Reset Electrical Data/Timing
Table 7-9. Timing Requirements for Reset (see Figure 7-4 and Figure 7-5)
OPP100
NO.
1
MIN
tw(RESET)
UNIT
12P (1)
ns
POR
2P
(2)
ns
RESET
2P (2)
ns
0
ns
Pulse duration, POR low or RESET low
2
tsu(BOOT)
Setup time, BTMODE[15:0] pins valid before POR high or
RESET high
3
th(BOOT)
Hold time, BTMODE[15:0] pins valid after POR high or RESET high
(1)
(2)
MAX
The device clock source must be stable and at a valid frequency prior to meeting the tw(RESET) requirement.
P = 1/(DEV Clock) frequency in ns.
Table 7-10. Switching Characteristics Over Recommended Operating Conditions During Reset
(see Figure 7-5)
NO.
4
OPP100
PARAMETER
td(RSTL-
MIN
MAX
UNIT
Delay time, RESET low or POR low to all I/Os entering their reset state
14
ns
Delay time, RESET high or POR high to all I/Os exiting their reset state
14
ns
IORST)
5
td(RSTHIOFUNC)
6
td(RSTH-
RESET assertion tw(RESET)
≥ 30P
0
2P
ns
RESET assertion tw(RESET)
< 30P
0
32P tw(RESET)
ns
Delay time, POR high to RSTOUT_WD_OUT high (1) (2)
0
12500P
ns
Delay time, RESET low to RSTOUT_WD_OUT Hi-Z (1) (2)
0
2P
ns
Delay time, RESET high to RSTOUT_WD_OUT high
(1) (2)
RSTOUTH)
7
td(PORHRSTOUTH)
8
td(RSTLRSTOUTZ)
(1)
(2)
194
For more detailed information on RSTOUT_WD_OUT pin behavior, see Section 7.3.14, RSTOUT_WD_OUT Pin.
P = 1/(DEV Clock) frequency in ns.
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 7-10. Switching Characteristics Over Recommended Operating Conditions During Reset
(see Figure 7-5) (continued)
NO.
td(PORH-
9
RSTOUTL)
10
OPP100
PARAMETER
td(RSTHRSTOUTD)
UNIT
MIN
MAX
Delay time, POR high to RSTOUT_WD_OUT driven based on latched BTMODE[11]
value (1) (2)
0
2P
ns
Delay time, RESET high to RSTOUT_WD_OUT driven based on latched BTMODE[11]
value (1) (2)
0
2P
ns
Figure 7-4 shows the Power-Up Timing. Figure 7-5 shows the Warm Reset (RESET) Timing. Max Reset
Timing is identical to Warm Reset Timing, except the BTMODE[15:0] pins are not re-latched.
Power
Supplies
Ramping
Power Supplies Stable
Clock Source Stable
DEV_CLKIN/
(A)
AUX_CLKIN
1
POR
RESET
7
9
RSTOUT_WD_OUT
Hi-Z
BTMODE[11]
(B)
5
3
2
BTMODE[15:0]
Hi-Z
Config
5
(C)
Other I/O Pins
A.
B.
C.
RESET STATE
Power supplies and DEV_CLKIN/AUX_CLKIN must be stable before the start of tw(RESET).
RSTOUT_WD_OUT only asserted if BTMODE[11] was latched as a "0" when coming out of reset.
For more detailed information on the RESET STATE of each pin, see Section 7.3.17, Pin Behaviors at Reset. Also
see Section 3.2, Terminal Functions for the IPU/IPD settings during reset.
Figure 7-4. Power-Up Timing
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
195
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Power Supplies Stable
DEV_CLKIN/
AUX_CLKIN
POR
1
RESET
8
6
10
Hi-Z
RSTOUT_WD_OUT
BTMODE[11]
5
4
3
2
Hi-Z
BTMODE[15:0]
Config
5
4
(B)
Other I/O Pins
A.
B.
(A)
RESET STATE
RSTOUT_WD_OUT only asserted if BTMODE[11] was latched as a "0" when coming out of reset.
For more detailed information on the RESET STATE of each pin, see Section 7.3.17, Pin Behaviors at Reset. Also
see Section 3.2, Terminal Functions for the IPU/IPD settings during reset.
Figure 7-5. Warm Reset (RESET) Timing
196
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
7.4
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Clocking
The device clocks are generated from several reference clocks that are fed to on-chip PLLs and dividers
(both inside and outside of the PRCM Module). Figure 7-6 shows a high-level overview of the device
system clocking structure (Note: to reduce complexity, not all clocking connections are shown). For
detailed information on the device clocks, see the Clock Generation and Management section of the
Power, Reset, and Clock Management (PRCM) Module chapter of the TMS320DM814x DaVinci Digital
Media Processors Technical Reference Manual (Literature Number: SPRUGZ8).
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
197
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
PLL_DSP
DSP
PLL_HDVPSS
HDVPSS
PLL_MEDIACTL
ISS, Media Controller
PRCM
PLL_HDVICP
SYSCLK3
HDVICP2
SYSCLK4
L3 Fast/Medium, L4 Fast,
EDMA, OCMC, MMU
PRCM
PLL_L3
L3/L4 Slow, GPMC, ELM,
McASP, McBSP,
UART3/4/5 (opt),
Mailbox, Spinlock
SYSCLK6
PLL_SGX
PRCM
SYSCLK23
SGX530
USB0/1
CLKDCO
PLL_USB
DEVOSC/
DEV_CLKIN
AUXOSC/
AUX_CLKIN
SYSCLK10
M
U
X
CLKOUT
PRCM
SPI0/1/2/3, I2C0/1/2/3,
UART0/1/2, HDMI CEC
SYSCLK8
(Note: Separate MUX
exists for each PLL)
MMC0/1/2
M
U
X
From SYSCLK6
UART3/4/5
PLL_DDR
DDR0/1
/2
DMM
HDVPSS SD VENC
PLL_VIDEO0
HDMI
PLL_VIDEO2
HDMI PHY
HDVPSS VOUT1
M
U
X
M
U
X
PLL_VIDEO1
PLL_AUDIO
HDVPSS VOUT0
PRCM
From PLL_VIDEO0/1/2
PRCM
SYSCLK20
SYSCLK21
From AUX Clock, AUD_CLK0/1/2
M
U
X
MCASP0/1/2 AUX_CLK
M
U
X
MCBSP CLKS,
HDMI I2S
From PLL_AUDIO, PLL_VIDEO0/1/2, AUX Clock, AUD_CLK0/1/2
PLL_ARM
(Embedded PLL)
MCASP3/4/5 AUX_CLK
M
U
X
RTCDIVIDER
From CLKIN32 Pin
PRCM
SYSCLK18
From DEV/AUX Clock, AUD_CLK0/1/2, TCLKIN
Cortex-A8
RTC, GPIO, SyncTimer,
Cortex-A8 (Optional)
M
U
X
TIMER1/2/3/4/5/6/7/8
WDT0 (Optional)
DCAN0/1
M
U
X
SERDES_CLK
SATA SERDES
(Embedded PLL)
EMAC Switch
PCIE SERDES
(Embedded PLL)
WDT0 (Optional)
RCOSC32K
Figure 7-6. System Clocking Overview
198
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
7.4.1
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Device (DEV) and Auxiliary (AUX) Clock Inputs
The device provides two clock inputs, Device (DEVOSC_MXI/DEV_CLKIN) and Auxiliary
(AUXOSC_MXI/AUX_CLKIN). The Device (DEV) clock is used to generate the majority of the internal
reference clocks, while the Auxiliary (AUX) clock can optionally be used as a source for the Audio and/or
Video PLLs.
The DEV and AUX clocks can be sourced in two ways:
1. Using an external crystal in conjunction with the internal oscillator or
2. Using an external 1.8-V LVCMOS-compatible clock input
Note: The external crystals used with the internal oscillators must operate in fundamental parallel
resonant mode only. There is no overtone support.
The DEV Clock should in most cases be 20 MHz. However, it can optionally range anywhere from 20 - 30
MHz if the following are true:
• The DEV Clock is not used to source the SATA reference clock
• A precise 32768-Hz clock is not needed for Real-Time Clock functionality
• If the boot mode is FAST XIP
The AUX Clock is optional and can range from 20-30 MHz. AUX Clock can be used to source the Audio
and/or Video PLLs when a very precise audio or video frequency is required.
7.4.1.1
Using the Internal Oscillators
When the internal oscillators are used to generate the DEV and AUX clocks, external crystals are required
to be connected across the DEVOSC or AUXOSC oscillator MXI and MXO pins, along with two load
capacitors (see Figure 7-7 and Figure 7-8). The external crystal load capacitors should also be connected
to the associated oscillator ground pin (VSSA_DEVOSC or VSSA_AUXOSC). The capacitors should not
be connected to board ground (VSS).
Figure 7-7. Device Oscillator
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
199
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
AUXOSC_MXI/
AUX_CLKIN
AUXOSC_MXO
Rd
(Optional)
Crystal
C1
VSSA_AUXOSC
C2
Figure 7-8. Auxiliary Oscillator
The load capacitors, C1 and C2 in the above pictures, should be chosen such that the below equation is
satisfied. CL in the equation is the load specified by the crystal manufacturer. All discrete components
used to implement the oscillator circuit should be placed as close as possible to the associated oscillator
MXI, MXO, and VSS pins.
CL =
C1 C2
(C1 + C2 )
Table 7-11. Input Requirements for Crystal Circuit on the Device Oscillator (DEVOSC)
PARAMETER
MIN
TYP
MAX
Start-up time (from power up until oscillating at stable frequency)
Crystal Oscillation frequency
(1)
20
Parallel Load Capacitance (C1 and C2)
20
12
Crystal ESR
Crystal Shunt Capacitance
Crystal Oscillation Mode
(1)
ms
30
MHz
24
pF
50
Ω
5
pF
Fundamental Only
Crystal Frequency Stability
UNIT
4
n/a
If Ethernet not used
±200
If MII is used and
RGMII, RMII not used
±100
If RGMII, or RMII used
±50
ppm
20-MHz DEV clock is required for all bootmodes other than Fast XIP. For more detailed information on boot modes, see the ROM Code
Memory and Peripheral Booting chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual
(Literature Number: SPRUGZ8).
Table 7-12. Input Requirements for Crystal Circuit on the Auxiliary Oscillator (AUXOSC)
PARAMETER
MIN
Start-up time (from power up until oscillating at stable frequency)
ms
20
30
MHz
Parallel Load Capacitance (C1 and C2)
12
24
pF
Crystal Shunt Capacitance
Crystal Oscillation Mode
50
Ω
5
pF
Fundamental Only
Crystal Frequency stability (1)
200
UNIT
4
Crystal Oscillation frequency
Crystal ESR
(1)
MAX
n/a
±50
ppm
Applies only when sourcing the HDMI or HDVPSS DAC clocks from the AUXOSC
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
7.4.1.2
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Using a 1.8V LVCMOS-Compatible Clock Input
A 1.8-V LVCMOS-Compatible Clock Input can be used instead of the internal oscillators as the DEV and
AUX clock inputs to the system. The external connections to support this are shown in Figure 7-9 and
Figure 7-10. The DEV_CLKIN and AUX_CLKIN pins are connected to the 1.8-V LVCMOS-Compatible
clock sources. The DEV_MXO and AUX_MXO pins are left unconnected. The VSSA_DEVOSC and
VSSA_AUXOSC pins are connected to board ground (VSS).
DEVOSC_MXI/
DEV_CLKIN
DEVOSC_MXO
VSSA_DEVOSC
NC
Figure 7-9. 1.8-V LVCMOS-Compatible Clock Input (DEV_OSC)
AUXOSC_MXI/
AUX_CLKIN
AUXOSC_MXO
VSSA_AUXOSC
NC
Figure 7-10. 1.8-V LVCMOS-Compatible Clock Input (AUX_OSC)
The clock source must meet the DEVOSC_MXI/DEV_CLKIN timing requirements shown in Table 7-15,
Timing Requirements for DEVOSC_MXI/DEV_CLKIN.
The clock source must meet the AUXOSC_MXI/AUX_CLKIN timing requirements shown in Table 7-16,
Timing Requirements for AUXOSC_MXI/AUX_CLKIN.
7.4.2
SERDES_CLKN/P Input Clock
A high-quality, low-jitter differential clock source is required for the PCIE PHY and is an optional clock
source for the SATA PHY. The clock is required to be AC coupled to the SERDES_CLKP and
SERDES_CLKN device pins according to the specifications in Table 7-13. Both the clock source and the
coupling capacitors should be placed physically as close to the processor as possible. In addition, make
sure to follow any PCB routing and termination recommendations that the clock source manufacturer
recommends.
Table 7-13. SERDES_CLKN/P AC Coupling Capacitors Recommendations
PARAMETER
SERDES_CLKN/P AC coupling capacitor value
MIN
TYP
MAX
0.24
0.27
1.0
UNIT
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
nF
201
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 7-13. SERDES_CLKN/P AC Coupling Capacitors Recommendations (continued)
PARAMETER
MIN
SERDES_CLKN/P AC coupling capacitor package size (1) (2)
(1)
(2)
TYP
MAX
UNIT
0402
0603
EIA
L x W, 10 Mil units, that is, a 0402 is a 40 x 20 Mil surface mount capacitor.
The physical size of the capacitor should be as small as practical. Use the same size on both lines in each pair placed side-by-side.
The differential clock source is required to meet the REFCLK AC Specifications outlined in the PCI
EXPRESS CARD ELECTROMECHANICAL SPECIFICATION, REV. 2.0, at the input to the AC coupling
capacitors.
In addition, LVDS clock sources that are compliant to the above specification, but with the following
exceptions, are also acceptable:
Table 7-14. Acceptable Exceptions to the REFCLK AC Specifications for LVDS Clock Sources
PARAMETER
MIN
MAX
UNIT
VIH
Differential High-Level Input Voltage
125
1000
mV
VIL
Differential Low-Level Input Voltage
-1000
-125
mV
7.4.3
AUD_CLKINx Input Clocks
External clock inputs can optionally be provided at the AUD_CLKIN0/1/2 pins to serve as a reference
clocks for the following modules:
• McASP3/4/5
• McBSP
• TIMER1/2/3/4/5/6/7/8
7.4.4
CLKIN32 Input Clock
An external 32768-Hz clock input can optionally be provided at the CLKIN32 pin to serve as a reference
clock in place of the RTCDIVIDER clock for the following Modules:
• RTC
• GPIO0/1/2/3
• TIMER1/2/3/4/5/6/7/8
• ARM Cortex-A8
• SYNCTIMER
The CLKIN32 source must meet the timing requirements shown in Table 7-18.
7.4.5
External Input Clocks
There are three pins referred to as AUD_CLKIN0,1,2 which are used as optional sources for HDMI I2S,
McASP, McBSP and TIMER1-8. The maximum IO pin frequency for these three input clocks is 50MHz.
7.4.6
Output Clocks Select Logic
The device includes two selectable general-purpose clock outputs (CLKOUT0 and CLKOUT1). The source
for these output clocks is controlled by the CLKOUT_MUX register in the Control Module (see Figure 711).
202
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
CLKOUT_MUX
RESERVED
RCOSC32K Output
PLL_SGX Output
DEV_OSC Clock Input
AUX Clock
DEV Clock
PLL_L3 Output
PLL_MEDIACTL Output / 2
PLL_DSS Output / 2
PCIE SERDES Observation Clock
SATA SERDES Observation Clock
PRCM SYSCLK Output
A.
1011-1111
1010
1001
1000
CLKOUT0
0111
CLKOUT1
0110
0101
0100
0011
0010
0001
0000
(A)
Muxed output of DEVOSC clock, USBPLL clock output, VIDEO0 PLL Clock output, and RTC DIVIDER output.
Figure 7-11. CLKOUTx Source Selection Logic
For detailed information on the CLKOUTx switching characteristics, see Table 7-19.
7.4.7
Input/Output Clocks Electrical Data/Timing
Note: If an external clock oscillator is used, a single clean power supply should be used to power both the
device and the external clock oscillator circuit.
Table 7-15. Timing Requirements for DEVOSC_MXI/DEV_CLKIN (1)
(2) (3)
(see Figure 7-12)
OPP100
NO
.
MIN
NOM
50
MAX
UNIT
1
tc(DMXI)
Cycle time, DEVOSC_MXI/DEV_CLKIN
33.33
50
ns
2
tw(DMXIH)
Pulse duration, DEVOSC_MXI/DEV_CLKIN high
0.45C
0.55C
ns
3
tw(DMXIL)
Pulse duration, DEVOSC_MXI/DEV_CLKIN low
0.45C
0.55C
ns
4
tt(DMXI)
Transition time, DEVOSC_MXI/DEV_CLKIN
7
ns
5
tJ(DMXI)
Period jitter, DEVOSC_MXI/DEV_CLKIN
0.02C
ns
Frequency Stability
If Ethernet not used
±200
If MII is used and RGMII, RMII not used
±100 ppm
If RGMII, or RMII used
(1)
(2)
(3)
±50
The DEVOSC_MXI/DEV_CLKIN frequency and PLL settings should be chosen such that the resulting SYSCLKs and Module Clocks are
within the specific ranges shown in the Section 7.4.9, SYSCLKs and Section 7.4.10, Module Clocks.
The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
C = DEV_CLKIN cycle time in ns. For example, when DEVOSC_MXI/DEV_CLKIN frequency is 20 MHz, use C = 50 ns.
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
203
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
5
1
1
4
2
DEVOSC_MXI/
DEV_CLKIN
3
4
Figure 7-12. DEV_MXI/DEV_CLKIN Timing
204
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 7-16. Timing Requirements for AUX_MXI/AUX_CLKIN
(see Figure 7-13)
OPP100
NO.
(1)
(2)
(3)
(1) (2)
MIN
NOM
33.3
50
MAX
UNIT
1
tc(AMXI)
Cycle time, AUXOSC_MXI/AUX_CLKIN
50
ns
2
tw(AMXIH)
Pulse duration, AUXOSC_MXI/AUX_CLKIN high
0.45C
0.55C
ns
3
tw(AMXIL)
Pulse duration, AUXOSC_MXI/AUX_CLKIN low
0.45C
0.55C
ns
4
tt(AMXI)
Transition time, AUXOSC_MXI/AUX_CLKIN
7
ns
5
tJ(AMXI)
Period jitter, AUXOSC_MXI/AUX_CLKIN
6
Sf
Frequency stability, AUXOSC_MXI/AUX_CLKIN (3)
0.02C
± 50
ns
ppm
The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
C = AUX_CLKIN cycle time in ns. For example, when AUXOSC_MXI/AUX_CLKIN frequency is 20 MHz, use C = 50 ns.
Applies only when sourcing the HDMI or HDVPSS DAC clocks from the AUXOSC.
5
1
1
4
2
AUXOSC_MXI/
AUX_CLKIN
3
4
Figure 7-13. AUX_MXI/AUX_CLKIN Timing
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
205
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 7-17. Timing Requirements for AUD_CLKINx
(1)
(see Figure 7-14)
OPP100/120/166
NO.
1
MIN
tc(AUD_CLKINx)
Cycle time, AUD_CLKINx
NOM
MAX
20
ns
2
tw(AUD_CLKINxH)
Cycle time, AUD_CLKINx
0.45A
0.55
A
3
tw(AUD_CLKINxL)
Cycle time, AUD_CLKINx
0.45A
0.55
A
(1)
UNIT
ns
ns
A = AUD_CLKINx cycle time in ns.
1
2
AUD_CLKINx
3
Figure 7-14. AUD_CLKINx Timing
206
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 7-18. Timing Requirements for CLKIN32
(1) (2)
(see Figure 7-15)
OPP100
NO.
NOM
MAX
1/32768
UNIT
1
tc(CLKIN32)
Cycle time, CLKIN32
2
tw(CLKIN32H)
Pulse duration, CLKIN32 high
0.45C
0.55C
ns
3
tw(CKIN32L)
Pulse duration, CLKIN32 low
0.45C
0.55C
ns
4
tt(CLKIN32)
Transition time, CLKIN32
7
ns
tJ(CLKIN32)
Period jitter, CLKIN32
0.02C
ns
5
(1)
(2)
MIN
s
The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
C = CLKIN32 cycle time in ns. For example, when CLKIN32 frequency is 32768 Hz, use C = 1/32768 s.
5
1
4
1
2
CLKIN32
3
4
Figure 7-15. CLKIN32 Timing
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
207
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 7-19. Switching Characteristics Over Recommended Operating Conditions for CLKOUTx (CLKOUT0
and CLKOUT1) (1) (2)
(see Figure 7-16)
NO.
OPP100
PARAMETER
MIN
MAX
1
tc(CLKOUTx)
Cycle time, CLKOUTx
2
tw(CLKOUTxH)
Pulse duration, CLKOUTx high
0.45P
0.55P
ns
3
tw(CLKOUTxL)
Pulse duration, CLKOUTx low
0.45P
0.55P
ns
4
tt(CLKOUTx)
Transition time, CLKOUTx
0.05P
ns
(1)
(2)
5
UNIT
ns
The reference points for the rise and fall transitions are measured at VOL MAX and VOH MIN.
P = 1/CLKOUTx clock frequency in nanoseconds (ns). For example, when CLKOUTx frequency is 200 MHz, use P = 5 ns.
2
4
1
CLKOUTx
(Divide-by-1)
3
4
Figure 7-16. CLKOUTx Timing
7.4.8
PLLs
The device contains 12 top-level PLLs, and 4 embedded PLLs (within the ARM Cortex-A8, PCIE, SATA,
and CSI) that provide clocks to different parts of the system. Figure 7-17 and Figure 7-18 show simplified
block diagrams of the Top-Level PLL and PLL_ARM. In addition, see the System Clocking Overview
(Figure 7-6) for a high-level view of the device clock architecture including the PLL reference clock
sources and connections.
DEV/AUX
Clock
1
(N + 1)
REFCLK
xM
Multiplier
CLKDCO
1
M2
CLKOUT
1
(N 2 + 1)
Figure 7-17. Top-Level PLL Simplified Block Diagram
DEV Clock
1
(N + 1)
REFCLK
x2M
Multiplier
DCOCLK
1
M2
1
2
CLKOUT
1
(N 2 + 1)
Figure 7-18. PLL_ARM Simplified Block Diagram
The reference clock for most of the PLLs comes from the DEV input clock, with select PLLs also having
the option to use the AUX input clock as a reference. Also, each PLL supports a Bypass mode in which
the reference clock can be directly passed to the PLL CLKOUT through a divider. All device PLL’s will
come-up in Bypass mode after reset.
For details on programming the device PLLs, see the Control Module chapter of the TMS320DM814x
DaVinci Digital Media Processors Technical Reference Manual (Literature Number: SPRUGZ8).
208
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
7.4.8.1
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
PLL Power Supply Filtering
The device PLLs are supplied externally via the VDDA_xPLL_1P8 power-supply pins (where "x"
represents ARM, DSP, VID0, VID1, AUDIO, DDR, and/or L3). External filtering must be added on the PLL
supply pins to ensure that the requirements in Table 7-20 are met.
Table 7-20. PLL Power Supply Requirements
PARAMETER
MIN
MAX
Dynamic noise at VDDA_xPLL_1P8 pins
7.4.8.2
50
UNIT
mV p-p
PLL Multipliers and Dividers
The Top-Level and PLL_ARM PLLs support the internal multiplier and divider values shown in Table 7-21,
Top-Level PLL Multiplier and Divider Limits and Table 7-22, PLL_ARM Multiplier and Divider Limits. The
PLLs must be programmed to conform to the various REFCLK, CLKDCO, DCOCLK, and CLKOUT limits
described in Section 7.4.8.3, PLL Frequency Limits.
Table 7-21. Top-Level PLL Multiplier and Divider Limits
PARAMETER
(1)
MIN
MAX
N Pre-Divider
0
255
PLL Multiplier (M)
2
4095 (1)
M2 Post Divider
1
127
N2 Bypass Divider
0
15
MIN
MAX
The PLL Multiplier supports fractional values (up to 18-bits of fraction) except when the PLL Multiplier is > 4093.
Table 7-22. PLL_ARM Multiplier and Divider Limits
PARAMETER
(1)
(2)
N Pre-Divider
0
127
PLL Multiplier (M) (1)
2
2047 (2)
M2 Post Divider
1
31
N2 Bypass Divider
0
15
This parameter describes the limits on the programmable multiplier value M. The multiplication factor for the PLL_ARM is equal to 2 * M
(also see Figure 7-18).
The PLL Multiplier supports fractional values (up to 18-bits of fraction) except when the PLL Multiplier is < 20 OR > 2045.
7.4.8.3
PLL Frequency Limits
Each PLL supports a minimum and maximum operating frequency for its REFCLK, CKLDCO, and
CLKOUT values. The PLLs must be configured not to exceed any of the constraints placed on these
values shown in Table 7-23 through Table 7-25. Care must be taken to stay within these limits when
selecting external clock input frequencies, internal divider values, and PLL multiply ratios. In addition,
limits shown in these tables may be further restricted by the clock frequency limitations of the device
modules using these clocks. For more detailed information on the SYSCLK and Module Clock frequency
limits, see Section 7.4.9, SYSCLKs and Section 7.4.10, Module Clocks.
Table 7-23. Top-Level PLL Frequency Ranges (ALL OPPs)
CLOCK
MIN
MAX
UNIT
REFCLK
0.5
2.5
MHz
1000
2000
MHz
500
1000
MHz
CLKDCO (HS1)
(1)
CLKDCO (HS2) (2)
(1)
(2)
The PLL has two modes of operation: HS1 and HS2. The mode of operation should be set, according to the desired CLKDCO
frequency, by programming the SELFREQDCO field of the ADPLLLJx_CLKCTRL registers in the Control Module.
CLKDCO of the PLL_USB is used undivided by the USB modules; therefore, CLKDCO for the PLL_USB PLL must be programmed to
960 MHz for proper operation.
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
209
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 7-23. Top-Level PLL Frequency Ranges (ALL OPPs) (continued)
CLOCK
MIN
MAX
UNIT
CLKOUT
see Table 7-25
see Table 7-25
MHz
Table 7-24. ARM Cortex-A8 Embedded PLL (PLL_ARM) Frequency Ranges (ALL OPPs)
CLOCK
MIN
MAX
UNIT
REFCLK
0.032
52
MHz
DCOCLK
20
2000
MHz
CLKOUT
see Table 7-25
see Table 7-25
MHz
Table 7-25. PLL CLKOUT Frequency Ranges
OPP100
PLL
(1)
7.4.8.4
UNIT
MIN
MAX
PLL_ARM
10
600
MHz
PLL_DSP
10
500
MHz
PLL_SGX
10
200
MHz
PLL_HDVICP
10
266
MHz
PLL_L3
10
200
MHz
PLL_DDR
10
400
MHz
PLL_HDVPSS
10
200
MHz
PLL_AUDIO
10
200
MHz
PLL_MEDIACTL
10
400
MHz
PLL_USB
10 (1)
960
MHz
PLL_VIDEO0
10
200
MHz
PLL_VIDEO1
10
200
MHz
PLL_VIDEO2
10
200
MHz
When the USB is used, PLL_USB must be fixed at 960 MHz.
PLL Register Descriptions
The PLL Control Registers reside in the Control Module and are listed in Section 4.1, Control Module of
this datasheet.
210
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
7.4.9
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
SYSCLKs
In some cases, the system clock inputs and PLL outputs are sent to the PRCM Module for division and
multiplexing before being routed to the various device Modules. These clock outputs from the PRCM
Module are called SYSCLKs. Table Table 7-26 lists the device SYSCLKs along with their maximum
supported clock frequencies. In addition, limits shown in these tables may be further restricted by the clock
frequency limitations of the device modules using these clocks. For more details on Module Clock
frequency limits, see Section 7.4.10 Module Clocks.
Table 7-26. Maximum SYSCLK Clock Frequencies (1)
(1)
SYSCLK
MAX CLOCK FREQUENCY
OPP100 (MHz)
SYSCLK1
RSV
SYSCLK2
RSV
SYSCLK3
266
SYSCLK4
200
SYSCLK5
RSV
SYSCLK6
100
SYSCLK7
RSV
SYSCLK8
192
SYSCLK9
RSV
SYSCLK10
48
SYSCLK11
RSV
SYSCLK12
RSV
SYSCLK13
RSV
SYSCLK14
27
SYSCLK15
RSV
SYSCLK16
27
SYSCLK17
RSV
SYSCLK18
0.032768
SYSCLK19
192
SYSCLK20
192
SYSCLK21
192
SYSCLK22
RSV
SYSCLK23
200
The maximum frequencies listed in this table are valid for OPP100. Some of these frequencies have
higher maximum values when OPP120 or OPP166 is used, see Table 7-4
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
211
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
7.4.10 Module Clocks
Device Modules either receive their clock directly from an external clock input, directly from a PLL, or from
a PRCM SYSCLK output. Table 7-27 lists the clock source options for each Module on this device, along
with the maximum frequency that Module can accept. To ensure proper Module functionality, the device
PLLs and dividers must be programmed not to exceed the maximum frequencies listed in this table.
Table 7-27. Maximum Module Clock Frequencies (1)
MODULE
CLOCK SOURCES
MAX FREQUENCY
OPP100 (MHz)
Cortex-A8
PLL_ARM
SYSCLK18
600
DCAN0/1
DEV Clock
30
DDR0/1
PLL_DDR
400
DMM
PLL_DDR/2
200
DSP
PLL_DSP
500
System MMU
SYSCLK4
200
EDMA
SYSCLK4
200
EMAC Switch (GMII)
SATA SERDES
Fixed 125
EMAC Switch (RGMII)
PLL_VIDEO0
PLL_VIDEO1
PLL_VIDEO02
PLL_L3
Fixed 250
EMAC Switch (RMII and MII)
SATA SERDES
EMAC_RMREFCLK Pin
Fixed 50
(1)
212
GPIO
SYSCLK6
100
GPIO Debounce
SYSCLK18
Fixed 0.032768
GPMC
SYSCLK6
100
HDMI
PLL_VIDEO2
186
HDMI CEC
SYSCLK10
Fixed 48
HDMI I2S
SYSCLK20
SYSCLK21
AUD_CLK0/1/2
AUX Clock
50
HDVICP2
SYSCLK3
266
HDVPSS
PLL_HDVPSS
200
HDVPSS VOUT1
PLL_VIDEO2
HDMI PHY
186
HDVPSS VOUT0
PLL_VIDEO1
PLL_VIDEO2
165
HDVPSS SD VENC
PLL_VIDEO0
Fixed 54
I2C0/1/2/3
SYSCLK10
48
ISS
PLL_ MEDIACTL
400
L3 Fast
SYSCLK4
200
L3 Medium
SYSCLK4
200
L3 Slow
SYSCLK6
100
L4 Fast
SYSCLK4
200
L4 Slow
SYSCLK6
100
Mailbox
SYSCLK6
100
McASP
SYSCLK6
100
McASP0/1/2 AUX_CLK
SYSCLK20
SYSCLK21
192
The maximum frequencies listed in this table are valid for OPP100. Some of these frequencies have higher maximum values when
OPP120 or OPP166 is used, see Table 7-4
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 7-27. Maximum Module Clock Frequencies(1) (continued)
MODULE
CLOCK SOURCES
MAX FREQUENCY
OPP100 (MHz)
McASP3/4/5 AUX_CLK
PLL_AUDIO
PLL_VIDEO0/1/2
AUD_CLK0/1/2
AUX Clock
192
McBSP CLKS
SYSCLK20
SYSCLK21
AUD_CLK0/1/2
AUX Clock
192
Media Controller
PLL_MEDIACTL/2
200
MMCSD0/1/2
SYSCLK8
192
OCMC RAM
SYSCLK4
200
PCIe SERDES
SERDES_CLKx Pins
100
SATA SERDES
DEV Clock
SERDES_CLKx Pins
20 or 100
200
SGX530
SYSCLK23
SPI0/1/2/3
SYSCLK10
48
Spinlock
SYSCLK6
100
Sync Timer
SYSCLK18
Fixed 0.032768
TIMER1/2/3/4/5/6/7/8
SYSCLK18
DEV Clock
AUX Clock
AUD_CLK0/1/2
TCLKIN
30
UART0/1/2
SYSCLK10
48
UART3/4/5
SYSCLK6
SYSCLK8
SYSCLK10
192
USB
PLL_USB CLKDCO
Fixed 960
WDT0
RTCDIVIDER
RCOSC32K
Fixed 0.032768
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
213
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
7.5
www.ti.com
Interrupts
The device has a large number of interrupts to service the needs of its many peripherals and subsystems.
The ARM Cortex-A8, C674x DSP, and Media Controller are capable of servicing these interrupts.
However, the C674x DSP require additional system-level interrupt multiplexors to receive their interrupts.
The following sections list the device interrupt mapping and multiplexing schemes.
7.5.1
ARM Cortex-A8 Interrupts
The ARM Cortex-A8 Interrupt Controller (AINTC) is responsible for prioritizing all service requests from the
System peripherals and generating either IRQs or FIQs to the Cortex-A8. The AINTC has the capability to
handle up to 128 requests, and the priority of the interrupt inputs are programmable. Table 7-28 lists the
interrupt sources for the AINTC.
Note: For General-Purpose devices, the AINTC does not support the generation of FIQs to the ARM
processor.
For more details on ARM Cortex-A8 interrupt control, see the ARM Interrupt Controller (AINTC) chapter of
the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
Table 7-28. ARM Cortex-A8 Interrupt Controller (AINTC) Interrupt Sources
Cortex-A8
INTERRUPT NUMBER
214
ACRONYM
SOURCE
0
EMUINT
Cortex-A8 Emulation
1
COMMTX
Cortex-A8 Emulation
2
COMMRX
Cortex-A8 Emulation
3
BENCH
Cortex-A8 Emulation
4
ELM_IRQ
5
–
Reserved
6
–
Reserved
7
NMI
NMIn Pin
8
–
Reserved
9
L3DEBUG
L3 Interconnect
10
L3APPINT
L3 Interconnect
11
TINT8
12
EDMACOMPINT
13
EDMAMPERR
EDMA Memory Protection Error
14
EDMAERRINT
EDMA CC Error
15
WDTINT0
Watchdog Timer 0
16
SATAINT
SATA
17
USBSSINT
18
USBINT0
USB0
19
USBINT1
USB1
ELM
TIMER8
EDMA CC Completion
USB Subsystem
20-27
–
Reserved
28
SDINT1
MMC/SD1
29
SDINT2
MMC/SD2
30
I2CINT2
I2C2
31
I2CINT3
I2C3
32
GPIOINT2A
GPIO2 A
33
GPIOINT2B
GPIO2 B
34
USBWAKEUP
USB Subsystem Wakeup
35
PCIeWAKEUP
PCIe Wakeup
Power, Reset, Clocking, and Interrupts
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 7-28. ARM Cortex-A8 Interrupt Controller (AINTC) Interrupt Sources (continued)
Cortex-A8
INTERRUPT NUMBER
ACRONYM
36
DSSINT
HDVPSS
37
GFXINT
SGX530
38
HDMIINT
HDMI
SOURCE
39
ISS_IRQ_5
40
3PGSWRXTHR0
EMAC Switch RX Threshold
41
3PGSWRXINT0
EMAC Switch Receive
42
3PGSWTXINT0
EMAC Switch Transmit
43
3PGSWMISC0
EMAC Switch Miscellaneous
44
UARTINT3
UART3
45
UARTINT4
UART4
46
UARTINT5
UART5
47
-
48
PCIINT0
PCIe
49
PCIINT1
PCIe
50
PCIINT2
PCIe
51
PCIINT3
PCIe
52
DCAN0_INT0
DCAN0
53
DCAN0_INT1
DCAN0
54
DCAN0_PARITY
55
DCAN1_INT0
DCAN1
56
DCAN1_INT1
DCAN1
57
DCAN1_PARITY
58-61
–
62
GPIOINT3A
GPIO3
63
GPIOINT3B
GPIO3
64
SDINT0
MMC/SD0
65
SPIINT0
SPI0
66
-
67
TINT1
TIMER1
68
TINT2
TIMER2
69
TINT3
TIMER3
70
I2CINT0
I2C0
71
I2CINT1
I2C1
72
UARTINT0
UART0
73
UARTINT1
UART1
74
UARTINT2
UART2
75
RTCINT
76
RTCALARMINT
77
MBINT
78
–
ISS
Reserved
DCAN0 Parity
DCAN1 Parity
Reserved
Reserved
RTC
RTC Alarm
Mailbox
Reserved
79
PLLINT
80
MCATXINT0
PLL Recalculation Interrupt
McASP0 Transmit
81
MCARXINT0
McASP0 Receive
82
MCATXINT1
McASP1 Transmit
83
MCARXINT1
McASP1 Receive
84
MCATXINT2
McASP2 Transmit
85
MCARXINT2
McASP2 Receive
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
215
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 7-28. ARM Cortex-A8 Interrupt Controller (AINTC) Interrupt Sources (continued)
216
Cortex-A8
INTERRUPT NUMBER
ACRONYM
86
MCBSPINT
87
–
Reserved
88
–
Reserved
91
–
Reserved
92
TINT4
TIMER4
93
TINT5
TIMER5
94
TINT6
TIMER6
95
TINT7
TIMER7
96
GPIOINT0A
GPIO0
97
GPIOINT0B
GPIO0
98
GPIOINT1A
GPIO1
99
GPIOINT1B
GPIO1
100
GPMCINT
GPMC
101
DDRERR0
DDR0
102
DDRERR1
DDR1
103
HDVICPCONT1SYNC
HDVICP2
104
HDVICPCONT2SYNC
HDVICP2
105
MCATXINT3
McASP3 Transmit
106
MCARXINT3
McASP3 Receive
107
IVA0MBOXINT
HDVICP2 Mailbox
108
MCATXINT4
McASP4 Transmit
109
MCARXINT4
McASP4 Receive
110
MCATXINT5
McASP5 Transmit
111
MCARXINT5
McASP5 Receive
112
TCERRINT0
EDMA TC 0 Error
113
TCERRINT1
EDMA TC 1 Error
114
TCERRINT2
EDMA TC 2 Error
115
TCERRINT3
EDMA TC 3 Error
116-119
–
122
MMUINT
123
MCMMUINT
124
DMMINT
DMM
125
SPIINT1
SPI1
126
SPIINT2
SPI2
127
SPIINT3
SPI3
Power, Reset, Clocking, and Interrupts
SOURCE
McBSP
Reserved
System MMU
Media Controller
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
7.5.2
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
C674x DSP Interrupts
The C674x DSP interrupt controller combines up to 128 device events into 12 prioritized interrupts
presented to the CPU. The default sources of the 128 device events are shown in Table 7-29. In addition,
device events 15 through 95 can alternatively be sourced from one of the 24 Multiplexed device events
shown in Table 7-30. The DSP_INTMUX_x registers in the Control Module are used to select between the
default event and the multiplexed event. The interrupt controller also controls the generation of the CPU
exceptions, NMI, and emulation interrupts.
Table 7-29. Default C674x Event Sources
C674x DEFAULT
EVENT NUMBER
ACRONYM
0
EVT0
C674x Interrupt Controller 0
1
EVT1
C674x Interrupt Controller 1
2
EVT2
C674x Interrupt Controller 2
3
EVT3
C674x Interrupt Controller 3
4
-
Reserved
5
-
Reserved
6
-
Reserved
7
-
Reserved
8
-
Reserved
9
EMU_DTDMA
10
-
11
EMU_RTDXRX
C674x-RTDX
12
EMU_RTDXTX
C674x-RTDX
13
IDMAINT0
C674x-ECM
14
C674x
C674x-ECM
15
SDINT0
MMC/SD0
16
SPIINT0
SPI0
17
–
18
ELM_IRQ
19
–
Reserved
20
EDMAINT
EDMA CC
21
EDMAERRINT
EDMA CC Error
22
TCERRINT0
EDMA TC0 Error
23
ISS_IRQ4
24
–
Reserved
25
–
Reserved
26
–
Reserved
27
TCERRINT1
EDMA TC1 Error
28
TCERRINT2
EDMA TC2 Error
29
TCERRINT3
EDMA TC3 Error
30
SDINT1
MMC/SD1
31
SDINT2
MMC/SD2
32
3PGSWRXTHR0
EMAC Switch RX Threshold
33
3PGSWRXINT0
EMAC Switch RX
34
3PGSWTXINT0
EMAC Switch TX
35
3PGSWMISC0
EMAC Switch Miscellaneous
36
PCIINT0
PCIe
37
PCIINT1
PCIe
38
PCIINT2
PCIe
SOURCE
C674x-ECM
Reserved
Reserved
ELM
ISS
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
217
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 7-29. Default C674x Event Sources (continued)
218
C674x DEFAULT
EVENT NUMBER
ACRONYM
39
PCIINT3
PCIe
40
DSSINT
DSS
41
HDMIINT
HDMI
42
SATAINT
SATA
43
GFXINT
SGX530
46
-
Reserved
47-48
-
Reserved
49
TINT1
TIMER1
50
TINT2
TIMER2
51
TINT3
TIMER3
52
TINT4
TIMER4
53
TINT5
TIMER5
54
TINT6
TIMER6
55
TINT7
TIMER7
56
MBINT
Mailbox
57
GPIOINT3A
GPIO3
58
I2CINT0
I2C0
59
I2CINT1
I2C1
60
UARTINT0
UART0
61
UARTINT1
UART1
62
UARTINT2
UART2
63
GPIOINT3B
GPIO3
64
GPIOINT0A
GPIO0
65
GPIOINT0B
GPIO0
66
GPIOINT1A
GPIO1
67
GPIOINT1B
GPIO1
68
GPIOINT2A
GPIO2
69
GPIOINT2B
GPIO2
70
MCATXINT0
McASP0 Transmit
71
MCARXINT0
McASP0 Receive
72
MCATXINT1
McASP1 Transmit
73
MCARXINT1
McASP1 Receive
74
MCATXINT2
McASP2 Transmit
75
MCARXINT2
McASP2 Receive
76
MCBSPINT
McBSP
77
UARTINT3
UART3
78
UARTINT4
UART4
79
UARTINT5
UART5
80
MCATXINT3
McASP3 Transmit
81
MCARXINT3
McASP3 Receive
82
MCATXINT4
McASP4 Transmit
83
MCARXINT4
McASP4 Receive
84
MCATXINT5
McASP5 Transmit
85
MCARXINT5
McASP5 Receive
86
SPIINT1
SPI1
87
SPIINT2
SPI2
88
SPIINT3
SPI3
Power, Reset, Clocking, and Interrupts
SOURCE
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 7-29. Default C674x Event Sources (continued)
C674x DEFAULT
EVENT NUMBER
ACRONYM
SOURCE
89
I2CINT2
90
HDVICPCONT1SYNC
I2C2
HDVICP2
91
HDVICPCONT2SYNC
HDVICP2
92
I2CINT3
I2C3
93
MMUINT
System MMU
94
HDVICPMBOXINT
95
GPMCINT
96
INTERR
C674x-Int Ctl
97
EMC_IDMAERR
C674x-EMC
98
-
Reserved
Reserved
HDVICP2 Mailbox
GPMC
99
-
100
EFIINTA
C674x-EFIA
101
EFIINTB
C674x-EFIB
102
-
Reserved
103
-
Reserved
104
-
Reserved
105
-
Reserved
106
-
Reserved
107
-
Reserved
108
-
Reserved
109
-
Reserved
110
-
Reserved
111
-
Reserved
112
-
Reserved
113
PMC_ED
114
-
Reserved
115
-
Reserved
116
UMC_ED1
C674x-UMC
117
UMC_ED2
C674x-UMC
118
PDC_INT
C674x-PDC
119
SYS_CMPA
C674x-SYS
120
PMC_CMPA
C674x-PMC
121
PMC_DMPA
C674x-PMC
122
DMC_CMPA
C674x-DMC
123
DMC_DMPA
C674x-DMC
124
UMC_CMPA
C674x-UMC
125
UMC_DMPA
C674x-UMC
126
EMC_CMPA
C674x-EMC
127
EMC_BUSERR
C674x-EMC
C674x-PMC
Power, Reset, Clocking, and Interrupts
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
219
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 7-30. Multiplexed C674x Event Sources
C674x MULTIPLEXED
EVENT NUMBER
220
ACRONYM
SOURCE
0
-
1
DCAN0_INT0
Default Event
DCAN0
2
DCAN0_INT1
DCAN0
3
DCAN1_PARITY
4
DCAN1_INT0
DCAN1
5
DCAN1_INT1
DCAN1
6
DCAN1_PARITY
7
–
Reserved
8
–
Reserved
DCAN0 Parity
DCAN1 Parity
9
–
Reserved
10
-
Reserved
11
L3DEBUG
L3 Interconnect
12
L3APPINT
L3 Interconnect
13
EDMAMPERR
14
TINT8
EDMA Memory Protection Error
TIMER8
15
WDTINT0
Watchdog Timer 0
16
USBSSINT
USB Subsystem
17
USBINT0
USB0
18
USBINT1
USB1
19
RTCINT
RTC
20
RTCALARMINT
21
-
Reserved
22
-
Reserved
23
DDRERR0
DDR0
24
DDRERR1
DDR1
Power, Reset, Clocking, and Interrupts
RTC Alarm
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8 Peripheral Information and Timings
8.1
Parameter Information
Tester Pin Electronics
42 Ω
3.5 nH
Transmission Line
Z0 = 50 Ω
(see Note)
4.0 pF
1.85 pF
Data Sheet Timing Reference Point
Output
Under
Test
Device Pin
(see Note)
NOTE: The data sheet provides timing at the device pin. For output timing analysis, the tester pin electronics and its transmission line effects must be
taken into account. A transmission line with a delay of 2 ns can be used to produce the desired transmission line effect. The transmission line is
intended as a load only. It is not necessary to add or subtract the transmission line delay (2 ns) from the data sheet timings.
Input requirements in this data sheet are tested with an input slew rate of < 4 Volts per nanosecond (4 V/ns) at the device pin.
Figure 8-1. Test Load Circuit for AC Timing Measurements
The load capacitance value stated is only for characterization and measurement of AC timing signals. This
load capacitance value does not indicate the maximum load the device is capable of driving.
8.1.1
1.8-V and 3.3-V Signal Transition Levels
All input and output timing parameters are referenced to Vref for both "0" and "1" logic levels. For 3.3-V I/O,
Vref = 1.5 V. For 1.8-V I/O, Vref = 0.9 V.
Vref
Figure 8-2. Input and Output Voltage Reference Levels for AC Timing Measurements
All rise and fall transition timing parameters are referenced to VIL MAX and VIH MIN for input clocks, VOL
MAX and VOH MIN for output clocks.
Vref = VIH MIN (or VOH MIN)
Vref = VIL MAX (or VOL MAX)
Figure 8-3. Rise and Fall Transition Time Voltage Reference Levels
8.1.2
3.3-V Signal Transition Rates
All timings are tested with an input edge rate of 4 volts per nanosecond (4 V/ns).
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
221
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.1.3
www.ti.com
Timing Parameters and Board Routing Analysis
The timing parameter values specified in this data manual do not include delays by board routings. As a
good board design practice, such delays must always be taken into account. Timing values may be
adjusted by increasing/decreasing such delays. TI recommends utilizing the available I/O buffer
information specification (IBIS) models to analyze the timing characteristics correctly. To properly use IBIS
models to attain accurate timing analysis for a given system, see the Using IBIS Models for Timing
Analysis application report (Literature Number: SPRA839). If needed, external logic hardware such as
buffers may be used to compensate any timing differences.
8.2
Recommended Clock and Control Signal Transition Behavior
All clocks and control signals must transition between VIH and VIL (or between VIL and VIH) in a monotonic
manner.
222
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
8.3
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Controller Area Network Interface (DCAN)
The device provides two DCAN interfaces for supporting distributed realtime control with a high level of
security. The DCAN interfaces implement the following features:
• Supports CAN protocol version 2.0 part A, B
• Bit rates up to 1 MBit/s
• 64 message objects
• Individual identifier mask for each message object
• Programmable FIFO mode for message objects
• Programmable loop-back modes for self-test operation
• Suspend mode for debug support
• Software module reset
• Automatic bus on after Bus-Off state by a programmable 32-bit timer
• Message RAM parity check mechanism
• Direct access to Message RAM during test mode
• CAN Rx/Tx pins are configurable as general-purpose IO pins
• Two interrupt lines (plus additional parity-error interrupts line)
• RAM initialization
• DMA support
For more detailed information on the DCAN peripheral, see the DCAN Controller Area Network chapter of
the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
8.3.1
DCAN Peripheral Register Descriptions
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
223
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.3.2
www.ti.com
DCAN Electrical Data/Timing
Table 8-1. Timing Requirements for DCANx Receive (1) (see Figure 8-4)
OPP100/120/166
NO.
1
(1)
MIN
f(baud)
Maximum programmable baud rate
tw(DCANRX)
Pulse duration, receive data bit (DCANx_RX)
NOM
UNIT
MAX
1
H-2
Mbps
H+2
ns
H = period of baud rate, 1/programmed baud rate.
Table 8-2. Switching Characteristics Over Recommended Operating Conditions for DCANx Transmit
(1)
(see Figure 8-4)
NO.
2
(1)
OPP100/120/166
PARAMETER
f(baud)
Maximum programmable baud rate
tw(DCANTX)
Pulse duration, transmit data bit (DCANx_TX)
MIN
MAX
1
H-2
H+2
UNIT
Mbps
ns
H = period of baud rate, 1/programmed baud rate.
1
DCANx_RX
2
DCANx_TX
Figure 8-4. DCANx Timings
224
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
8.4
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
EDMA
The EDMA controller handles all data transfers between memories and the device slave peripherals on
the device. These data transfers include cache servicing, non-cacheable memory accesses, userprogrammed data transfers, and host accesses.
8.4.1
EDMA Channel Synchronization Events
The EDMA Channel controller supports up to 64 channels that service peripherals and memory. Each
EDMA channel is mapped to a defaul EDMA synchronization event as shown in Table 8-3. By default,
each event uses the parameter entry that matches its event number. However, because the device
includes a channel mapping feature, each event may be mapped to any of 512 parameter table entries.
For more detailed information, see the Enhanced Direct Memory Access Controller chapter of the
TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
Table 8-3. EDMA Default Synchronization Events
EVENT
NUMBER
DEFAULT
EVENT NAME
DEFAULT EVENT DESCRIPTION
0-1
–
2
SDTXEVT1
Reserved
SD1 Transmit
3
SDRXEVT1
SD1 Receive
4-7
–
Reserved
8
AXEVT0
McASP0 Transmit
9
AREVT0
McASP0 Receive
10
AXEVT1
McASP1 Transmit
11
AREVT1
McASP1 Receive
12
AXEVT2
McASP2 Transmit
13
AREVT2
McASP2 Receive
14
BXEVT
McBSP Transmit
15
BREVT
McBSP Receive
16
SPI0XEVT0
SPI0 Transmit 0
17
SPI0REVT0
SPI0 Receive 0
18
SPI0XEVT1
SPI0 Transmit 1
19
SPI0REVT1
SPI0 Receive 1
20
SPI0XEVT2
SPI0 Transmit 2
21
SPI0REVT2
SPI0 Receive 2
22
SPI0XEVT3
SPI0 Transmit 3
23
SPI0REVT3
SPI0 Receive 3
24
SDTXEVT0
SD0 Transmit
25
SDRXEVT0
SD0 Receive
26
UTXEVT0
UART0 Transmit
27
URXEVT0
UART0 Receive
28
UTXEVT1
UART1 Transmit
29
URXEVT1
UART1 Receive
30
UTXEVT2
UART2 Transmit
UART2 Receive
31
URXEVT2
32-35
–
36
ISS_DMA_REQ1
ISS Event 1
37
ISS_DMA_REQ2
ISS Event 2
38
ISS_DMA_REQ3
ISS Event 3
39
ISS_DMA_REQ4
ISS Event 4
Reserved
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
225
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-3. EDMA Default Synchronization Events (continued)
EVENT
NUMBER
DEFAULT
EVENT NAME
40
CAN_IF1DMA
DCAN0 IF1
41
CAN_IF2DMA
DCAN0 IF2
42
SPI1XEVT0
SPI1 Transmit 0
43
SPI1REVT0
SPI1 Receive 0
44
SPI1XEVT1
SPI1 Transmit 1
45
SPI1REVT1
SPI1 Receive 1
DEFAULT EVENT DESCRIPTION
46
–
47
CAN_IF3DMA
Reserved
48
TINT4
TIMER4
49
TINT5
TIMER5
50
TINT6
TIMER6
51
TINT7
TIMER7
52
GPMCEVT
GPMC
53
HDMIEVT
HDMI
54
–
Reserved
55
–
Reserved
DCAN0 IF3
56
AXEVT3
McASP3 Transmit
57
AREVT3
McASP3 Receive
58
I2CTXEVT0
I2C0 Transmit
59
I2CRXEVT0
I2C0 Receive
60
I2CTXEVT1
I2C1 Transmit
61
I2CRXEVT1
I2C1 Receive
62
AXEVT4
McASP4 Transmit
63
AREVT4
McASP4 Receive
Table 8-4. EDMA Multiplexed Synchronization Events
EVT_MUX_x
VALUE
226
MULTIPLEXED
EVENT NAME
MULTIPLEXED EVENT DESCRIPTION
0
-
Default Event
1
SDTXEVT2
SD2 Transmit
2
SDRXEVT2
SD2 Receive
3
I2CTXEVT2
I2C2 Transmit
4
I2CRXEVT2
I2C2 Receive
5
I2CTXEVT3
I2C3 Transmit
6
I2CRXEVT3
I2C3 Receive
7
UTXEVT3
UART3 Transmit
8
URXEVT3
UART3 Receive
9
UTXEVT4
UART4 Transmit
10
URXEVT4
UART4 Receive
11
UTXEVT5
UART5 Transmit
12
URXEVT5
UART5 Receive
13
CAN_IF1DMA
DCAN1 IF1
14
CAN_IF2DMA
DCAN1 IF2
15
CAN_IF3DMA
DCAN1 IF3
16
SPI2XEVT0
SPI2 Transmit 0
17
SPI2REVT0
SPI2 Receive 0
18
SPI2XEVT1
SPI2 Transmit 1
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-4. EDMA Multiplexed Synchronization Events (continued)
8.4.2
EVT_MUX_x
VALUE
MULTIPLEXED
EVENT NAME
19
SPI2REVT1
SPI2 Receive 1
20
SPI3XEVT0
SPI3 Transmit 0
21
SPI3REVT0
SPI3 Receive 0
MULTIPLEXED EVENT DESCRIPTION
22
–
23
TINT1
Reserved
TIMER1
24
TINT2
TIMER2
25
TINT3
TIMER3
26
AXEVT5
McASP5 Transmit
27
AREVT5
McASP5 Receive
28
EDMAEVT0
EDMA_EVT0 Pin
29
EDMAEVT1
EDMA_EVT1 Pin
30
EDMAEVT2
EDMA_EVT2 Pin
31
EDMAEVT3
EDMA_EVT3 Pin
EDMA Peripheral Register Descriptions
Table 8-5. EDMA Channel Controller (EDMA TPCC) Control Registers
HEX ADDRESS
ACRONYM
0x4900 0000
PID
REGISTER NAME
Peripheral Identification
0x4900 0004
CCCFG
0x4900 0100 - 0x4900 01FC
DCHMAP0-63
EDMA3CC Configuration
0x4900 0200
QCHMAP0
QDMA Channel 0 Mapping
0x4900 0204
QCHMAP1
QDMA Channel 1 Mapping
DMA Channel 0-63 Mappings
0x4900 0208
QCHMAP2
QDMA Channel 2 Mapping
0x4900 020C
QCHMAP3
QDMA Channel 3 Mapping
0x4900 0210
QCHMAP4
QDMA Channel 4 Mapping
0x4900 0214
QCHMAP5
QDMA Channel 5 Mapping
0x4900 0218
QCHMAP6
QDMA Channel 6 Mapping
0x4900 021C
QCHMAP7
QDMA Channel 7 Mapping
0x4900 0240
DMAQNUM0
DMA Queue Number 0
0x4900 0244
DMAQNUM1
DMA Queue Number 1
0x4900 0248
DMAQNUM2
DMA Queue Number 2
0x4900 024C
DMAQNUM3
DMA Queue Number 3
0x4900 0250
DMAQNUM4
DMA Queue Number 4
0x4900 0254
DMAQNUM5
DMA Queue Number 5
0x4900 0258
DMAQNUM6
DMA Queue Number 6
0x4900 025C
DMAQNUM7
DMA Queue Number 7
0x4900 0260
QDMAQNUM
QDMA Queue Number
0x4900 0284
QUEPRI
Queue Priority
0x4900 0300
EMR
Event Missed
0x4900 0304
EMRH
Event Missed High
0x4900 0308
EMCR
Event Missed Clear
0x4900 030C
EMCRH
Event Missed Clear High
0x4900 0310
QEMR
0x4900 0314
QEMCR
QDMA Event Missed
QDMA Event Missed Clear
0x4900 0318
CCERR
EDMA3CC Error
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
227
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-5. EDMA Channel Controller (EDMA TPCC) Control Registers (continued)
228
HEX ADDRESS
ACRONYM
REGISTER NAME
0x4900 031C
CCERRCLR
EDMA3CC Error Clear
0x4900 0320
EEVAL
Error Evaluate
0x4900 0340
DRAE0
DMA Region Access Enable for Region 0
0x4900 0344
DRAEH0
0x4900 0348
DRAE1
0x4900 034C
DRAEH1
0x4900 0350
DRAE2
0x4900 0354
DRAEH2
0x4900 0358
DRAE3
0x4900 035C
DRAEH3
0x4900 0360
DRAE4
0x4900 0364
DRAEH4
0x4900 0368
DRAE5
0x4900 036C
DRAEH5
0x4900 0370
DRAE6
0x4900 0374
DRAEH6
0x4900 0378
DRAE7
DMA Region Access Enable High for Region 0
DMA Region Access Enable for Region 1
DMA Region Access Enable High for Region 1
DMA Region Access Enable for Region 2
DMA Region Access Enable High for Region 2
DMA Region Access Enable for Region 3
DMA Region Access Enable High for Region 3
DMA Region Access Enable for Region 4
DMA Region Access Enable High for Region 4
DMA Region Access Enable for Region 5
DMA Region Access Enable High for Region 5
DMA Region Access Enable for Region 6
DMA Region Access Enable High for Region 6
DMA Region Access Enable for Region 7
0x4900 037C
DRAEH7
DMA Region Access Enable High for Region 7
0x4900 0380 - 0x4900 039C
QRAE0-7
QDMA Region Access Enable for Region 0-7
0x4900 0400 - 0x4900 04FC
Q0E0-Q3E15
0x4900 0600 - 0x4900 060C
QSTAT0-3
Queue Status 0-3
0x4900 0620
QWMTHRA
Queue Watermark Threshold A
0x4900 0640
CCSTAT
EDMA3CC Status
0x4900 0800
MPFAR
Memory Protection Fault Address
0x4900 0804
MPFSR
Memory Protection Fault Status
0x4900 0808
MPFCR
Memory Protection Fault Command
0x4900 080C
MPPAG
Memory Protection Page Attribute Global
0x4900 0810 - 0x4900 082C
MPPA0-7
0x4900 1000
ER
0x4900 1004
ERH
Event High
0x4900 1008
ECR
Event Clear
0x4900 100C
ECRH
0x4900 1010
ESR
0x4900 1014
ESRH
Event Set High
Chained Event
Event Queue Entry Q0E0-Q3E15
Memory Protection Page Attribute 0-7
Event
Event Clear High
Event Set
0x4900 1018
CER
0x4900 101C
CERH
0x4900 1020
EER
0x4900 1024
EERH
Event Enable High
0x4900 1028
EECR
Event Enable Clear
0x4900 102C
EECRH
0x4900 1030
EESR
0x4900 1034
EESRH
0x4900 1038
SER
0x4900 103C
SERH
Secondary Event High
0x4900 1040
SECR
Secondary Event Clear
0x4900 1044
SECRH
0x4900 1050
IER
Peripheral Information and Timings
Chained Event High
Event Enable
Event Enable Clear High
Event Enable Set
Event Enable Set High
Secondary Event
Secondary Event Clear High
Interrupt Enable
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-5. EDMA Channel Controller (EDMA TPCC) Control Registers (continued)
HEX ADDRESS
ACRONYM
0x4900 1054
IERH
Interrupt Enable High
Interrupt Enable Clear
0x4900 1058
IECR
0x4900 105C
IECRH
0x4900 1060
IESR
0x4900 1064
IESRH
0x4900 1068
IPR
0x4900 106C
IPRH
REGISTER NAME
Interrupt Enable Clear High
Interrupt Enable Set
Interrupt Enable Set High
Interrupt Pending
Interrupt Pending High
0x4900 1070
ICR
0x4900 1074
ICRH
Interrupt Clear
Interrupt Clear High
0x4900 1078
IEVAL
Interrupt Evaluate
0x4900 1080
QER
QDMA Event
0x4900 1084
QEER
0x4900 1088
QEECR
QDMA Event Enable
QDMA Event Enable Clear
0x4900 108C
QEESR
QDMA Event Enable Set
0x4900 1090
QSER
QDMA Secondary Event
0x4900 1094
QSECR
QDMA Secondary Event Clear
Shadow Region 0 Channel Registers
0x4900 2000
ER
0x4900 2004
ERH
Event
Event High
0x4900 2008
ECR
Event Clear
0x4900 200C
ECRH
Event Clear High
0x4900 2010
ESR
0x4900 2014
ESRH
Event Set High
0x4900 2018
CER
Chained Event
0x4900 201C
CERH
0x4900 2020
EER
0x4900 2024
EERH
Event Enable High
Event Enable Clear
0x4900 2028
EECR
0x4900 202C
EECRH
0x4900 2030
EESR
0x4900 2034
EESRH
Event Set
Chained Event High
Event Enable
Event Enable Clear High
Event Enable Set
Event Enable Set High
0x4900 2038
SER
0x4900 203C
SERH
Secondary Event High
0x4900 2040
SECR
Secondary Event Clear
0x4900 2044
SECRH
0x4900 2050
IER
0x4900 2054
IERH
Interrupt Enable High
Interrupt Enable Clear
0x4900 2058
IECR
0x4900 205C
IECRH
0x4900 2060
IESR
0x4900 2064
IESRH
0x4900 2068
IPR
0x4900 206C
IPRH
0x4900 2070
ICR
Secondary Event
Secondary Event Clear High
Interrupt Enable
Interrupt Enable Clear High
Interrupt Enable Set
Interrupt Enable Set High
Interrupt Pending
Interrupt Pending High
Interrupt Clear
0x4900 2074
ICRH
Interrupt Clear High
0x4900 2078
IEVAL
Interrupt Evaluate
0x4900 2080
QER
QDMA Event
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
229
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-5. EDMA Channel Controller (EDMA TPCC) Control Registers (continued)
HEX ADDRESS
ACRONYM
0x4900 2084
QEER
REGISTER NAME
QDMA Event Enable
0x4900 2088
QEECR
QDMA Event Enable Clear
0x4900 208C
QEESR
QDMA Event Enable Set
0x4900 2090
QSER
QDMA Secondary Event
0x4900 2094
QSECR
0x4900 2200 - 0x4900 2294
-
Shadow Region 1 Channels
0x4900 2400 - 0x4900 2494
-
Shadow Region 2 Channels
...
QDMA Secondary Event Clear
...
0x4900 2E00 - 0x4900 2E94
-
Shadow Channels for MP Space 7
Table 8-6. EDMA Transfer Controller (EDMA TPTC) Control Registers
230
TPTC0 HEX
ADDRESS
TPTC1 HEX
ADDRESS
TPTC2 HEX
ADDRESS
TPTC3 HEX
ADDRESS
ACRONYM
0x4980 0000
0x4990 0000
0x49A0 0000
0x49B0 0000
PID
Peripheral Identification
0x4980 0004
0x4990 0004
0x49A0 0004
0x49B0 0004
TCCFG
EDMA3TC Configuration
0x4980 0100
0x4990 0100
0x49A0 0100
0x49B0 0100
TCSTAT
EDMA3TC Channel Status
0x4980 0120
0x4990 0120
0x49A0 0120
0x49B0 0120
ERRSTAT
Error Status
0x4980 0124
0x4990 0124
0x49A0 0124
0x49B0 0124
ERREN
Error Enable
0x4980 0128
0x4990 0128
0x49A0 0128
0x49B0 0128
ERRCLR
Error Clear
0x4980 012C
0x4990 012C
0x49A0 012C
0x49B0 012C
ERRDET
Error Details
0x4980 0130
0x4990 0130
0x49A0 0130
0x49B0 0130
ERRCMD
Error Interrupt Command
0x4980 0140
0x4990 0140
0x49A0 0140
0x49B0 0140
RDRATE
Read Rate Register
0x4980 0240
0x4990 0240
0x49A0 0240
0x49B0 0240
SAOPT
Source Active Options
0x4980 0244
0x4990 0244
0x49A0 0244
0x49B0 0244
SASRC
Source Active Source Address
REGISTER NAME
0x4980 0248
0x4990 0248
0x49A0 0248
0x49B0 0248
SACNT
Source Active Count
0x4980 024C
0x4990 024C
0x49A0 024C
0x49B0 024C
SADST
Source Active Destination
Address
0x4980 0250
0x4990 0250
0x49A0 0250
0x49B0 0250
SABIDX
Source Active Source B-Index
0x4980 0254
0x4990 0254
0x49A0 0254
0x49B0 0254
SAMPPRXY
Source Active Memory
Protection Proxy
0x4980 0258
0x4990 0258
0x49A0 0258
0x49B0 0258
SACNTRLD
Source Active Count Reload
0x4980 025C
0x4990 025C
0x49A0 025C
0x49B0 025C
SASRCBREF
Source Active Source Address
B-Reference
0x4980 0260
0x4990 0260
0x49A0 0260
0x49B0 0260
SADSTBREF
Source Active Destination
Address B-Reference
0x4980 0280
0x4990 0280
0x49A0 0280
0x49B0 0280
DFCNTRLD
0x4980 0284
0x4990 0284
0x49A0 0284
0x49B0 0284
DFSRCBREF
Destination FIFO Set
Destination Address B
Reference
0x4980 0288
0x4990 0288
0x49A0 0288
0x49B0 0288
DFDSTBREF
Destination FIFO Set
Destination Address B
Reference
0x4980 0300
0x4990 0300
0x49A0 0300
0x49B0 0300
DFOPT0
Destination FIFO Options 0
0x4980 0304
0x4990 0304
0x49A0 0304
0x49B0 0304
DFSRC0
Destination FIFO Source
Address 0
Destination FIFO Set Count
Reload
0x4980 0308
0x4990 0308
0x49A0 0308
0x49B0 0308
DFCNT0
Destination FIFO Count 0
0x4980 030C
0x4990 030C
0x49A0 030C
0x49B0 030C
DFDST0
Destination FIFO Destination
Address 0
0x4980 0310
0x4990 0310
0x49A0 0310
0x49B0 0310
DFBIDX0
Destination FIFO BIDX 0
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-6. EDMA Transfer Controller (EDMA TPTC) Control Registers (continued)
TPTC0 HEX
ADDRESS
TPTC1 HEX
ADDRESS
TPTC2 HEX
ADDRESS
TPTC3 HEX
ADDRESS
ACRONYM
0x4980 0314
0x4990 0314
0x49A0 0314
0x49B0 0314
DFMPPRXY0
0x4980 0340
0x4990 0340
0x49A0 0340
0x49B0 0340
DFOPT1
Destination FIFO Options 1
0x4980 0344
0x4990 0344
0x49A0 0344
0x49B0 0344
DFSRC1
Destination FIFO Source
Address 1
REGISTER NAME
Destination FIFO Memory
Protection Proxy 0
0x4980 0348
0x4990 0348
0x49A0 0348
0x49B0 0348
DFCNT1
Destination FIFO Count 1
0x4980 034C
0x4990 034C
0x49A0 034C
0x49B0 034C
DFDST1
Destination FIFO Destination
Address 1
0x4980 0350
0x4990 0350
0x49A0 0350
0x49B0 0350
DFBIDX1
Destination FIFO BIDX 1
0x4980 0354
0x4990 0354
0x49A0 0354
0x49B0 0354
DFMPPRXY1
Destination FIFO Memory
Protection Proxy 1
0x4980 0380
0x4990 0380
0x49A0 0380
0x49B0 0380
DFOPT2
Destination FIFO Options 2
0x4980 0384
0x4990 0384
0x49A0 0384
0x49B0 0384
DFSRC2
Destination FIFO Source
Address 2
0x4980 0388
0x4990 0388
0x49A0 0388
0x49B0 0388
DFCNT2
Destination FIFO Count 2
0x4980 038C
0x4990 038C
0x49A0 038C
0x49B0 038C
DFDST2
Destination FIFO Destination
Address 2
0x4980 0390
0x4990 0390
0x49A0 0390
0x49B0 0390
DFBIDX2
Destination FIFO BIDX 2
0x4980 0394
0x4990 0394
0x49A0 0394
0x49B0 0394
DFMPPRXY2
Destination FIFO Memory
Protection Proxy 2
0x4980 03C0
0x4990 03C0
0x49A0 03C0
0x49B0 03C0
DFOPT3
Destination FIFO Options 3
0x4980 03C4
0x4990 03C4
0x49A0 03C4
0x49B0 03C4
DFSRC3
Destination FIFO Source
Address 3
0x4980 03C8
0x4990 03C8
0x49A0 03C8
0x49B0 03C8
DFCNT3
Destination FIFO Count 3
0x4980 03CC
0x4990 03CC
0x49A0 03CC
0x49B0 03CC
DFDST3
Destination FIFO Destination
Address 3
0x4980 03D0
0x4990 03D0
0x49A0 03D0
0x49B0 03D0
DFBIDX3
Destination FIFO BIDX 3
0x4980 03D4
0x4990 03D4
0x49A0 03D4
0x49B0 03D4
DFMPPRXY3
Destination FIFO Memory
Protection Proxy 3
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
231
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.5
8.5.1
www.ti.com
Emulation Features and Capability
Advanced Event Triggering (AET)
The device supports Advanced Event Triggering (AET). This capability can be used to debug complex
problems as well as understand performance characteristics of user applications. AET provides the
following capabilities:
• Hardware Program Breakpoints: specify addresses or address ranges that can generate events such
as halting the processor or triggering the trace capture.
• Data Watchpoints: specify data variable addresses, address ranges, or data values that can generate
events such as halting the processor or triggering the trace capture.
• Counters: count the occurrence of an event or cycles for performance monitoring.
• State Sequencing: allows combinations of hardware program breakpoints and data watchpoints to
precisely generate events for complex sequences.
For more information on AET, see the following documents:
• Using Advanced Event Triggering to Find and Fix Intermittent Real-Time Bugs application report
(Literature Number: SPRA753)
• Using Advanced Event Triggering to Debug Real-Time Problems in High Speed Embedded
Microprocessor Systems application report (Literature Number: SPRA387)
8.5.2
Trace
The device supports Trace at the Cortex™-A8, C674x, and System levels. Trace is a debug technology
that provides a detailed, historical account of application code execution, timing, and data accesses. Trace
collects, compresses, and exports debug information for analysis. The debug information can be exported
to the Embedded Trace Buffer (ETB), or to the 5-pin Trace Interface (system trace only). Trace works in
real-time and does not impact the execution of the system.
For more information on board design guidelines for Trace Advanced Emulation, see the Emulation and
Trace Headers Technical Reference Manual (Literature Number: SPRU655).
8.5.3
IEEE 1149.1 JTAG
The JTAG (IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture)
interface is used for BSDL testing and emulation of the device. The TRST pin only needs to be released
when it is necessary to use a JTAG controller to debug the device or exercise the boundary scan
functionality of the device. For maximum reliability, the device includes an internal pulldown (IPD) on the
TRST pin to ensure that TRST is always asserted upon power up and the internal emulation logic of the
device is always properly initialized. JTAG controllers from Texas Instruments actively drive TRST high.
However, some third-party JTAG controllers may not drive TRST high but expect the use of a pullup
resistor on TRST. When using this type of JTAG controller, assert TRST to initialize the device after
powerup and externally drive TRST high before attempting any emulation or boundary-scan operations.
The main JTAG features include:
• 32KB embedded trace buffer (ETB)
• 5-pin system trace interface for debug
• Supports Advanced Event Triggering (AET)
• All processors can be emulated via JTAG ports
• All functions on EMU pins of the device:
– EMU[1:0] - cross-triggering, boot mode (WIR), STM trace
– EMU[4:2] - STM trace only (single direction)
232
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
8.5.3.1
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
JTAG ID (JTAGID) Register Description
Table 8-7. JTAG ID Register (1)
(1)
(2)
HEX ADDRESS
ACRONYM
0x4814 0600
JTAGID
REGISTER NAME
JTAG Identification Register (2)
IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture.
Read-only. Provides the device 32-bit JTAG ID.
The JTAG ID register is a read-only register that identifies to the customer the JTAG/device ID. For this
device, the JTAG ID register resides at address location 0x4814 0600. The register hex value for the
device is: 0x0B8F 202F. For the actual register bit names and their associated bit field descriptions, see
Figure 8-5 and Table 8-8.
31
28 27
12 11
1
0
VARIANT (4bit)
PART NUMBER (16-bit)
MANUFACTURER (11-bit)
LSB
R-xxxx
R-1011 1000 1111 0010
R-0000 0010 111
R-1
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Figure 8-5. JTAG ID Register Description - Device Register Value: 0x0B8F 202F
Table 8-8. JTAG ID Register Selection Bit Descriptions
Bit
Field
Description
31:28
VARIANT
Variant (4-bit) value. Device value: xxxx. This value reflects the device silicon revision [For example, 0x0
(0000) for initial silicon revision (SR) 1.0].
•
SR2.1, 0011, register value: 0x3B8F 202F
•
SR3.0, 0100, register value: 0x4B8F 202F
For more detailed information on the current device silicon revision, see the TMS320DM814x DaVinci™
Digital Media Processors Silicon Errata (Silicon Revisions 3.0, 2.1) (Literature Number: SPRZ343).
27:12
PART NUMBER
Part Number (16-bit) value. Device value: 0xB8F2 (1011 1000 1111 0010)
11:1
MANUFACTURER
Manufacturer (11-bit) value. Device value: 0x017 (0000 0010 111)
LSB
LSB. This bit is read as a ""1 for this device.
0
8.5.3.2
JTAG Electrical Data/Timing
Table 8-9. Timing Requirements for IEEE 1149.1 JTAG
(see Figure 8-6)
OPP100/120/166
NO.
MIN
MAX
UNIT
1
tc(TCK)
Cycle time, TCK
51.15
ns
1a
tw(TCKH)
Pulse duration, TCK high (40% of tc)
20.46
ns
1b
tw(TCKL)
Pulse duration, TCK low (40% of tc)
20.46
ns
3
tsu(TDI-TCK)
Input setup time, TDI valid to TCK high (20% of (tc * 0.5))
5.115
ns
3
tsu(TMS-TCK)
Input setup time, TMS valid to TCK high (20% of (tc * 0.5))
5.115
ns
th(TCK-TDI)
Input hold time, TDI valid from TCK high
10
ns
th(TCK-TMS)
Input hold time, TMS valid from TCK high
10
ns
4
Table 8-10. Switching Characteristics Over Recommended Operating Conditions for IEEE 1149.1 JTAG
(see Figure 8-6)
NO.
2
(1)
PARAMETER
td(TCKL-TDOV)
Delay time, TCK low to TDO valid
OPP100/120/166
MIN
MAX
0
23.575 (1)
UNIT
ns
(0.5 * tc) - 2
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
233
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
1
1a
1b
TCK
2
TDO
3
4
TDI/TMS
Figure 8-6. JTAG Timing
Table 8-11. Timing Requirements for IEEE 1149.1 JTAG With RTCK
(see Figure 8-6)
OPP100/120/166
NO.
MIN
MAX
UNIT
1
tc(TCK)
Cycle time, TCK
51.15
ns
1a
tw(TCKH)
Pulse duration, TCK high (40% of tc)
20.46
ns
1b
tw(TCKL)
Pulse duration, TCK low (40% of tc)
20.46
ns
3
tsu(TDI-TCK)
Input setup time, TDI valid to TCK high (20% of (tc * 0.5))
5.115
ns
3
tsu(TMS-TCK)
Input setup time, TMS valid to TCK high (20% of (tc * 0.5))
5.115
ns
th(TCK-TDI)
Input hold time, TDI valid from TCK high
10
ns
th(TCK-TMS)
Input hold time, TMS valid from TCK high
10
ns
4
Table 8-12. Switching Characteristics Over Recommended Operating Conditions for IEEE 1149.1 JTAG
With RTCK
(see Figure 8-7)
NO.
OPP100/120/166
PARAMETER
MIN
MAX
0
21
UNIT
5
td(TCK-RTCK)
Delay time, TCK to RTCK with no selected subpaths (that is,
ICEPick is the only tap selected - when the ARM is in the scan
chain, the delay time is a function of the ARM functional clock.)
6
tc(RTCK)
Cycle time, RTCK
51.15
ns
7
tw(RTCKH)
Pulse duration, RTCK high (40% of tc)
20.46
ns
8
tw(RTCKL)
Pulse duration, RTCK low (40% of tc)
20.46
ns
ns
5
TCK
6
7
8
RTCK
Figure 8-7. JTAG With RTCK Timing
234
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-13. Switching Characteristics Over Recommended Operating Conditions for STM Trace
(see Figure 8-8)
NO.
1
2
3
(1)
OPP100/120/166
PARAMETER
MIN
MAX
UNIT
tw(EMUH50)
Pulse duration, EMUx high detected at 50% VOH with 60/40 duty
cycle
4 (1)
ns
tw(EMUH90)
Pulse duration, EMUx high detected at 90% VOH
3.5
ns
tw(EMUL50)
Pulse duration, EMUx low detected at 50% VOH with 60/40 duty
cycle
4 (1)
ns
tw(EMUL10)
Pulse duration, EMUx low detected at 10% VOH
3.5
ns
tsko(EMU)
Output skew time, time delay difference between EMUx pins
configured as trace.
tskp(EMU)
Pulse skew, magnitude of difference between high-to-low (tPHL)
and low-to-high (tPLH) propagation delays
tsldp_o(EMU)
Output slew rate EMUx
-2
0.5
ns
1 (1)
ns
3.3
V/ns
This parameter applies to the maximum trace export frequency operating in a 40/60 duty cycle.
Buffer
Inputs
A
Buffers
EMUx Pins
B
tPLH
tPHL
1
2
B
A
3
C
C
Figure 8-8. STM Trace Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
235
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.6
www.ti.com
Ethernet MAC Switch (EMAC SW)
The EMAC SW controls the flow of packet data between the device and two external Ethernet PHYs, with
hardware flow control and quality-of-service (QOS) support. The EMAC SW contains a 3-port gigabit
switch, where one port is internally connected and the other two ports are brought out externally. Each of
the external EMAC ports supports 10Base-T (10 Mbits/second [Mbps]), and 100BaseTX (100 Mbps), in
either half- or full-duplex mode, and 1000BaseT (1000 Mbps) in full-duplex mode.
The EMAC SW controls the flow of packet data from the device to the external PHYs. The EMAC0/1 ports
on the device support four interface modes: Media Independent Interface (MII), Gigabit Media
Independent Interface (GMII), Reduced Media Independent Interface (RMII) and Reduced Gigabit Media
Independent Interface (RGMII). In addition, a single MDIO interface is pinned out to control the PHY
configuration and status monitoring. Multiple external PHYs can be controlled by the MDIO interface.
The EMAC SW module conforms to the IEEE 802.3-2002 standard, describing the “Carrier Sense Multiple
Access with Collision Detection (CSMA/CD) Access Method and Physical Layer” specifications. The IEEE
802.3 standard has also been adopted by ISO/IEC and re-designated as ISO/IEC 8802-3:2000(E).
Deviating from this standard, the EMAC SW module does not use the Transmit Coding Error signal
MTXER. Instead of driving the error pin when an underflow condition occurs on a transmitted frame, the
EMAC SW will intentionally generate an incorrect checksum by inverting the frame CRC, so that the
transmitted frame will be detected as an error by the network. In addition, the EMAC SW I/Os operate at
3.3 V and are not compatible with 2.5-V I/O signaling. Therefore, only Ethernet PHYs with 3.3-V I/O
interface should be used.
In networking systems, packet transmission and reception are critical tasks. The communications port
programming interface (CPPI) protocol maximizes the efficiency of interaction between the host software
and communications modules. The CPPI block contains 2048 words of 32-bit buffer descriptor memory
that holds up to 512 buffer descriptors.
For more detailed information on the EMAC SW module, see the 3PSW Ethernet Subsystem chapter of
the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
8.6.1
EMAC Peripheral Register Descriptions
Table 8-14. Ethernet MAC Switch Registers
ARM/L3 MASTERS
EMAC HEX
ADDRESS RANGE
236
ACRONYM
REGISTER NAME
0x4A10 0000
CPSW_ID_VER
0x4A10 0004
CPSW_CONTROL
CPSW ID Version Register
0x4A10 0008
CPSW_SOFT_RESET
0x4A10 000C
CPSW_STAT_PORT_EN
CPSW Statistics Port Enable Register
0x4A10 0010
CPSW_PTYPE
CPSW Transmit Priority Type Register
0x4A10 0014
CPSW_SOFT_IDLE
CPSW Software Idle
CPSW Throughput Rate
CPSW Switch Control Register
CPSW Soft Reset Register
0x4A10 0018
CPSW_THRU_RATE
0x4A10 001C
CPSW_GAP_THRESH
0x4A10 0020
CPSW_TX_START_WDS
CPSW Transmit Start Words
0x4A10 0024
CPSW_FLOW_CONTROL
CPSW Flow Control
0x4A10 0028
P0_MAX_BLKS
0x4A10 002C
P0_BLK_CNT
0x4A10 0030
P0_TX_IN_CTL
CPSW CPGMAC_SL Short Gap Threshold
CPSW Port 0 Maximum FIFO Blocks Register
CPSW Port 0 FIFO Block Usage Count Register (Read Only)
CPSW Port 0 Transmit FIFO Control
0x4A10 0034
P0_PORT_VLAN
CPSW Port 0 VLAN Register
0x4A10 0038
P0_TX_PRI_MAP
CPSW Port 0 Tx Header Priority to Switch Priority Mapping Register
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-14. Ethernet MAC Switch Registers (continued)
ARM/L3 MASTERS
EMAC HEX
ADDRESS RANGE
ACRONYM
REGISTER NAME
0x4A10 003C
CPDMA_TX_PRI_MAP
CPSW CPDMA TX (Port 0 Rx) Packet Priority to Header Priority Mapping
Register
0x4A10 0040
CPDMA_RX_CH_Map
CPSW CPDMA RX (Port 0 Tx) Switch Priority to DMA Channel Mapping
Register
0x4A10 0050
P1_MAX_BLKS
0x4A10 0054
P1_BLK_CNT
CPSW Port 1 Maximum FIFO Blocks Register
CPSW Port 1 FIFO Block Usage Count (Read Only)
0x4A10 0058
P1_TX_IN_CTL
0x4A10 005C
P1_PORT_VLAN
CPSW Port 1 Transmit FIFO Control
CPSW Port 1 VLAN Register
0x4A10 0060
P1_TX_PRI_MAP
CPSW Port 1 Tx Header Priority to Switch Priority Mapping Register
0x4A10 0064
P1_TS_CTL
0x4A10 0068
P1_TS_SEQ_LTYPE
CPSW_3GF Port 1 Time Sync Control Register
0x4A10 006C
P1_TS_VLAN
0x4A10 0070
SL1_SA_LO
CPSW CPGMAC_SL1 Source Address Low Register
0x4A10 0074
SL1_SA_HI
CPSW CPGMAC_SL1 Source Address High Register
0x4A10 0078
P1_SEND_PERCENT
0x4A10 007C – 0x4A10 008C
–
0x4A10 0090
P2_MAX_BLKS
0x4A10 0094
P2_BLK_CNT
0x4A10 0098
P2_TX_IN_CTL
CPSW_3GF Port 1 Time Sync LTYPE (and SEQ_ID_OFFSET)
CPSW_3GF Port 1 Time Sync VLAN2 and VLAN2 Register
CPSW Port 1 Transmit Queue Send Percentages
Reserved
CPSW Port 2 Maximum FIFO Blocks Register
CPSW Port 2 FIFO Block Usage Count (Read Only)
CPSW Port 2 Transmit FIFO Control
0x4A10 009C
P2_PORT_VLAN
CPSW Port 2 VLAN Register
0x4A10 00A0
P2_TX_PRI_MAP
CPSW Port 2 Tx Header Priority to Switch Priority Mapping Register
0x4A10 00A4
P2_TS_CTL
0x4A10 00A8
P2_TS_SEQ_LTYPE
0x4A10 00AC
P2_TS_VLAN
0x4A10 00B0
SL2_SA_LO
CPSW CPGMAC_SL2 Source Address Low Register
0x4A10 00B4
SL2_SA_HI
CPSW CPGMAC_SL2 Source Address High Register
0x4A10 00B8
P2_SEND_PERCENT
0x4A10 00BC – 0x4A10 00FC
–
0x4A10 0100
TX_IDVER
0x4A10 0104
TX_CONTROL
0x4A10 0108
TX_TEARDOWN
0x4A10 010C
–
0x4A10 0110
RX_IDVER
CPSW_3GF Port 2 Time Sync Control Register
CPSW_3GF Port 2 Time Sync LTYPE (and SEQ_ID_OFFSET)
CPSW_3GF Port 2 Time Sync VLAN2 and VLAN2 Register
CPSW Port 2 Transmit Queue Send Percentages
Reserved
CPDMA_REGS TX Identification and Version Register
CPDMA_REGS TX Control Register
CPDMA_REGS TX Teardown Register
Reserved
CPDMA_REGS RX Identification and Version Register
0x4A10 0114
RX_CONTROL
0x4A10 0118
RX_TEARDOWN
CPDMA_REGS RX Control Register
0x4A10 011C
SOFT_RESET
CPDMA_REGS Soft Reset Register
0x4A10 0120
DMACONTROL
CPDMA_REGS CPDMA Control Register
0x4A10 0124
DMASTATUS
CPDMA_REGS CPDMA Status Register
0x4A10 0128
RX_BUFFER_OFFSET
CPDMA_REGS RX Teardown Register
CPDMA_REGS Receive Buffer Offset
0x4A10 012C
EMCONTROL
0x4A10 0130
TX_PRI0_RATE
CPDMA_REGS Emulation Control
CPDMA_REGS Transmit (Ingress) Priority 0 Rate
0x4A10 0134
TX_PRI1_RATE
CPDMA_REGS Transmit (Ingress) Priority 1 Rate
0x4A10 0138
TX_PRI2_RATE
CPDMA_REGS Transmit (Ingress) Priority 2 Rate
0x4A10 013C
TX_PRI3_RATE
CPDMA_REGS Transmit (Ingress) Priority 3 Rate
0x4A10 0140
TX_PRI4_RATE
CPDMA_REGS Transmit (Ingress) Priority 4 Rate
0x4A10 0144
TX_PRI5_RATE
CPDMA_REGS Transmit (Ingress) Priority 5 Rate
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
237
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-14. Ethernet MAC Switch Registers (continued)
ARM/L3 MASTERS
EMAC HEX
ADDRESS RANGE
ACRONYM
0x4A10 0148
TX_PRI6_RATE
CPDMA_REGS Transmit (Ingress) Priority 6 Rate
0x4A10 014C
TX_PRI7_RATE
CPDMA_REGS Transmit (Ingress) Priority 7 Rate
REGISTER NAME
0x4A10 0150 – 0x4A10 017C
–
0x4A10 0180
TX_INTSTAT_RAW
0x4A10 0184
TX_INTSTAT_MASKED
0x4A10 0188
TX_INTMASK_SET
0x4A10 018C
TX_INTMASK_CLEAR
CPDMA_INT TX Interrupt Mask Clear Register
0x4A10 0190
CPDMA_IN_VECTOR
CPDMA_INT Input Vector (Read Only)
0x4A10 0194
CPDMA_EOI_VECTOR
0x4A10 0198 – 0x4A10 019C
–
0x4A10 01A0
RX_INTSTAT_RAW
0x4A10 01A4
RX_INTSTAT_MASKED
(1)
238
Reserved
CPDMA_INT TX Interrupt Status Register (Raw Value)
CPDMA_INT TX Interrupt Status Register (Masked Value)
CPDMA_INT TX Interrupt Mask Set Register
CPDMA_INT End Of Interrupt Vector
Reserved
CPDMA_INT RX Interrupt Status Register (Raw Value)
CPDMA_INT RX Interrupt Status Register (Masked Value)
0x4A10 01A8
RX_INTMASK_SET
0x4A10 01AC
RX_INTMASK_CLEAR
CPDMA_INT RX Interrupt Mask Set Register
CPDMA_INT RX Interrupt Mask Clear Register
0x4A10 01B0
DMA_INTSTAT_RAW
CPDMA_INT DMA Interrupt Status Register (Raw Value)
0x4A10 01B4
DMA_INTSTAT_MASKED
CPDMA_INT DMA Interrupt Status Register (Masked Value)
0x4A10 01B8
DMA_INTMASK_SET
0x4A10 01BC
DMA_INTMASK_CLEAR
CPDMA_INT DMA Interrupt Mask Set Register
0x4A10 01C0
RX0_PENDTHRESH
CPDMA_INT Receive Threshold Pending Register Channel 0
0x4A10 01C4
RX1_PENDTHRESH
CPDMA_INT Receive Threshold Pending Register Channel 1
0x4A10 01C8
RX2_PENDTHRESH
CPDMA_INT Receive Threshold Pending Register Channel 2
0x4A10 01CC
RX3_PENDTHRESH
CPDMA_INT Receive Threshold Pending Register Channel 3
0x4A10 01D0
RX4_PENDTHRESH
CPDMA_INT Receive Threshold Pending Register Channel 4
0x4A10 01D4
RX5_PENDTHRESH
CPDMA_INT Receive Threshold Pending Register Channel 5
0x4A10 01D8
RX6_PENDTHRESH
CPDMA_INT Receive Threshold Pending Register Channel 6
0x4A10 01DC
RX7_PENDTHRESH
CPDMA_INT Receive Threshold Pending Register Channel 7
0x4A10 01E0
RX0_FREEBUFFER
CPDMA_INT Receive Free Buffer Register Channel 0
0x4A10 01E4
RX1_FREEBUFFER
CPDMA_INT Receive Free Buffer Register Channel 1
0x4A10 01E8
RX2_FREEBUFFER
CPDMA_INT Receive Free Buffer Register Channel 2
0x4A10 01EC
RX3_FREEBUFFER
CPDMA_INT Receive Free Buffer Register Channel 3
0x4A10 01F0
RX4_FREEBUFFER
CPDMA_INT Receive Free Buffer Register Channel 4
0x4A10 01F4
RX5_FREEBUFFER
CPDMA_INT Receive Free Buffer Register Channel 5
CPDMA_INT DMA Interrupt Mask Clear Register
0x4A10 01F8
RX6_FREEBUFFER
CPDMA_INT Receive Free Buffer Register Channel 6
0x4A10 01FC
RX7_FREEBUFFER
CPDMA_INT Receive Free Buffer Register Channel 7
0x4A10 0200
TX0_HDP
CPDMA_STATERAM TX Channel 0 Head Desc Pointer
(1)
0x4A10 0204
TX1_HDP
CPDMA_STATERAM TX Channel 1 Head Desc Pointer
(1)
0x4A10 0208
TX2_HDP
CPDMA_STATERAM TX Channel 2 Head Desc Pointer
(1)
0x4A10 020C
TX3_HDP
CPDMA_STATERAM TX Channel 3 Head Desc Pointer
(1)
0x4A10 0210
TX4_HDP
CPDMA_STATERAM TX Channel 4 Head Desc Pointer
(1)
0x4A10 0214
TX5_HDP
CPDMA_STATERAM TX Channel 5 Head Desc Pointer
(1)
0x4A10 0218
TX6_HDP
CPDMA_STATERAM TX Channel 6 Head Desc Pointer
(1)
0x4A10 021C
TX7_HDP
CPDMA_STATERAM TX Channel 7 Head Desc Pointer
(1)
0x4A10 0220
RX0_HDP
CPDMA_STATERAM RX 0 Channel 0 Head Desc Pointer
(1)
0x4A10 0224
RX1_HDP
CPDMA_STATERAM RX 1 Channel 1 Head Desc Pointer
(1)
0x4A10 0228
RX2_HDP
CPDMA_STATERAM RX 2 Channel 2 Head Desc Pointer
(1)
Denotes CPPI 3.0 registers.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-14. Ethernet MAC Switch Registers (continued)
ARM/L3 MASTERS
EMAC HEX
ADDRESS RANGE
ACRONYM
0x4A10 022C
RX3_HDP
CPDMA_STATERAM RX 3 Channel 3 Head Desc Pointer
(1)
0x4A10 0230
RX4_HDP
CPDMA_STATERAM RX 4 Channel 4 Head Desc Pointer
(1)
0x4A10 0234
RX5_HDP
CPDMA_STATERAM RX 5 Channel 5 Head Desc Pointer
(1)
0x4A10 0238
RX6_HDP
CPDMA_STATERAM RX 6 Channel 6 Head Desc Pointer
(1)
0x4A10 023C
RX7_HDP
CPDMA_STATERAM RX 7 Channel 7 Head Desc Pointer
(1)
0x4A10 0240
TX0_CP
CPDMA_STATERAM TX Channel 0 Completion Pointer Register (1)
0x4A10 0244
TX1_CP
CPDMA_STATERAM TX Channel 1 Completion Pointer Register
(1)
0x4A10 0248
TX2_CP
CPDMA_STATERAM TX Channel 2 Completion Pointer Register
(1)
0x4A10 024C
TX3_CP
CPDMA_STATERAM TX Channel 3 Completion Pointer Register
(1)
0x4A10 0250
TX4_CP
CPDMA_STATERAM TX Channel 4 Completion Pointer Register
(1)
0x4A10 0254
TX5_CP
CPDMA_STATERAM TX Channel 5 Completion Pointer Register
(1)
0x4A10 0258
TX6_CP
CPDMA_STATERAM TX Channel 6 Completion Pointer Register
(1)
0x4A10 025C
TX7_CP
CPDMA_STATERAM TX Channel 7 Completion Pointer Register
(1)
0x4A10 0260
RX0_CP
CPDMA_STATERAM RX Channel 0 Completion Pointer Register
(1)
0x4A10 0264
RX1_CP
CPDMA_STATERAM RX Channel 1 Completion Pointer Register
(2)
0x4A10 0268
RX2_CP
CPDMA_STATERAM RX Channel 2 Completion Pointer Register
(2)
0x4A10 026C
RX3_CP
CPDMA_STATERAM RX Channel 3 Completion Pointer Register
(2)
0x4A10 0270
RX4_CP
CPDMA_STATERAM RX Channel 4 Completion Pointer Register
(2)
0x4A10 0274
RX5_CP
CPDMA_STATERAM RX Channel 5 Completion Pointer Register
(2)
0x4A10 0278
Rx6_CP
CPDMA_STATERAM RX Channel 6 Completion Pointer Register
(2)
0x4A10 027C
Rx7_CP
CPDMA_STATERAM RX Channel 7 Completion Pointer Register
(2)
0x4A10 02C0 - 0x4A10 03FC
–
Reserved
0x4A10 0400
RXGOODFRAMES
0x4A10 0404
RXBROADCASTFRAMES
CPSW_STATS Total Number of Good Broadcast Frames Received
0x4A10 0408
RXMULTICASTFRAMES
CPSW_STATS Total Number of Good Multicast Frames Received
0x4A10 040C
RXPAUSEFRAMES
CPSW_STATS Total Number of Good Frames Received
CPSW_STATS PauseRxFrames
0x4A10 0410
RXCRCERRORS
0x4A10 0414
RXALIGNCODEERRORS
CPSW_STATS Total Number of Alignment/Code Errors Received
0x4A10 0418
RXOVERSIZEDFRAMES
CPSW_STATS Total Number of Oversized Frames Received
0x4A10 041C
0x4A10 0420
0x4A10 0424
RXJABBERFRAMES
CPSW_STATS Total Number of CRC Errors Frames Received
CPSW_STATS Total number of Jabber Frames Received
RXUNDERSIZEDFRAMES CPSW_STATS Total Number of Undersized Frames Received
RXFRAGMENTS
CPSW_STATS RxFragments Received
0x4A10 0428 - 0x4A10 042C
–
0x4A10 0430
RXOCTETS
0x4A10 0434
TXGOODFRAMES
0x4A10 0438
TXBROADCASTFRAMES
CPSW_STATS BroadcastTxFrames
0x4A10 043C
TXMULTICASTFRAMES
CPSW_STATS MulticastTxFrames
0x4A10 0440
TXPAUSEFRAMES
CPSW_STATS PauseTxFrames
0x4A10 0444
TXDEFERREDFRAMES
CPSW_STATS Deferred Frames
CPSW_STATS Collisions
0x4A10 0448
TXCOLLISIONFRAMES
0x4A10 044C
TXSINGLECOLLFRAMES
0x4A10 0450
TXMULTCOLLFRAMES
0x4A10 0454
0x4A10 0458
(2)
REGISTER NAME
Reserved. Read as Zero
CPSW_STATS Total Number of Received Bytes in Good Frames
CPSW_STATS GoodTxFrames
CPSW_STATS SingleCollisionTxFrames
CPSW_STATS MultipleCollisionTxFrames
TXEXCESSIVECOLLISION CPSW_STATS ExcessiveCollisions
S
TXLATECOLLISIONS
CPSW_STATS LateCollisions
Denotes CPPI 3.0 registers.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
239
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-14. Ethernet MAC Switch Registers (continued)
ARM/L3 MASTERS
EMAC HEX
ADDRESS RANGE
0x4A10 045C
0x4A10 0460
ACRONYM
TXUNDERRUN
REGISTER NAME
CPSW_STATS Transmit Underrun Error
TXCARRIERSENSEERRO CPSW_STATS CarrierSenseErrors
RS
0x4A10 0464
TXOCTETS
0x4A10 0468
64OCTETFRAMES
CPSW_STATS TxOctets
0x4A10 046C
65T127OCTETFRAMES
CPSW_STATS 65-127octetFrames
0x4A10 0470
128T255OCTETFRAMES
CPSW_STATS 128-255octetFrames
0x4A10 0474
256T511OCTETFRAMES
CPSW_STATS 256-511octetFrames
0x4A10 0478
512T1023OCTETFRAMES CPSW_STATS 512-1023octetFrames
0x4A10 047C
1024TUPOCTETFRAMES
0x4A10 0480
NETOCTETS
0x4A10 0484
RXSOFOVERRUNS
CPSW_STATS Receive FIFO or DMA Start of Frame Overruns
CPSW_STATS 64octetFrames
CPSW_STATS 1023-1518octetFrames
CPSW_STATS NetOctets
0x4A10 0488
RXMOFOVERRUNS
CPSW_STATS Receive FIFO or DMA Mid of Frame Overruns
0x4A10 048C
RXDMAOVERRUNS
CPSW_STATS Receive DMA Start of Frame and Middle of Frame
Overruns
0x4A10 0490 - 0x4A10 04FC
–
Reserved
0x4A10 0500
CPTS_IDVER
0x4A10 0504
CPTS_CONTROL
0x4A10 0508
CPTS_RFTCLK_SEL
Reference Clock Select Register
0x4A10 050C
CPTS_TS_PUSH
Time Stamp Event Push Register
0x4A10 0510
CPTS_TS_LOAD_VAL
Time Stamp Load Value Register
0x4A10 0514
CPTSTS_LOAD_EN
Time Stamp Load Enable Register
0x4A10 0518 - 0x4A10 051C
–
0x4A10 0520
0x4A10 0524
0x4A10 0528
CPTS_INTSTAT_RAW
Identification and Version Register
Time Sync Control Register
Reserved
Time Sync Interrupt Status Raw Register
CPTS_INTSTAT_MASKED Time Sync Interrupt Status Masked Register
CPTS_INT_ENABLE
Time Sync Interrupt Enable Register
0x4A10 052C
–
0x4A10 0530
CPTS_EVENT_POP
Event Interrupt Pop Register
0x4A10 0534
CPTS_EVENT_LOW
Lower 32-Bits of the Event Value
Upper 32-Bits of the Event Value
0x4A10 0538
CPTS_EVENT_HIGH
0x4A10 053C - 0x4A10 05FC
–
0x4A10 0600
ALE_IDVER
0x4A10 0604
–
0x4A10 0608
ALE_CONTROL
0x4A10 060C
–
0x4A10 0610
ALE_PRESCALE
0x4A10 0614
–
0x4A10 0618
ALE_UNKNOWN_VLAN
0x4A10 061C
–
Reserved
Reserved
Address Lookup Engine ID/Version Register
Reserved
Address Lookup Engine Control Register
Reserved
Address Lookup Engine Prescale Register
Reserved
Address Lookup Engine Unknown VLAN Register
Reserved
0x4A10 0620
ALE_TBLCTL
0x4A10 0624 - 0x4A10 0630
–
0x4A10 0634
ALE_TBLW2
Address Lookup Engine Table Word 2 Register
0x4A10 0638
ALE_TBLW1
Address Lookup Engine Table Word 1 Register
0x4A10 063C
ALE_TBLW0
Address Lookup Engine Table Word 0 Register
0x4A10 0640
ALE_PORTCTL0
Address Lookup Engine Port 0 Control Register
0x4A10 0644
ALE_PORTCTL1
Address Lookup Engine Port 1 Control Register
240
Peripheral Information and Timings
Address Lookup Engine Table Control
Reserved
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-14. Ethernet MAC Switch Registers (continued)
ARM/L3 MASTERS
EMAC HEX
ADDRESS RANGE
ACRONYM
REGISTER NAME
0x4A10 0648
ALE_PORTCTL2
0x4A10 064C
–
Address Lookup Engine Port 2 Control Register
Reserved
0x4A10 0650
–
Reserved
0x4A10 0654
–
Reserved
0x4A10 0658 - 0x4A10 06FF
–
Reserved
0x4A10 0700
SL1_IDVER
0x4A10 0704
SL1_MACCONTROL
CPGMAC_SL1 Mac Control Register
0x4A10 0708
SL1_MACSTATUS
CPGMAC_SL1 Mac Status Register
0x4A10 070C
SL1_SOFT_RESET
CPGMAC_SL1 Soft Reset Register
0x4A10 0710
SL1_RX_MAXLEN
CPGMAC_SL1 RX Maximum Length Register
0x4A10 0714
SL1_BOFFTEST
CPGMAC_SL1 Backoff Test Register
0x4A10 0718
SL1_RX_PAUSE
CPGMAC_SL1 Receive Pause Timer Register
0x4A10 071C
SL1_TX_PAUSE
CPGMAC_SL1 Transmit Pause Timer Register
0x4A10 0720
SL1_EMCONTROL
CPGMAC_SL1 Emulation Control Register
0x4A10 0724
SL1_RX_PRI_MAP
CPGMAC_SL1 Rx Pkt Priority to Header Priority Mapping Register
0x4A10 0728 - 0x4A10 073C
–
CPGMAC_SL1 ID/Version Register
Reserved
0x4A10 0740
SL2_IDVER
0x4A10 0744
SL2_MACCONTROL
CPGMAC_SL2 ID/Version Register
CPGMAC_SL2 Mac Control Register
0x4A10 0748
SL2_MACSTATUS
CPGMAC_SL2 Mac Status Register
0x4A10 074C
SL2_SOFT_RESET
CPGMAC_SL2 Soft Reset Register
0x4A10 0750
SL2_RX_MAXLEN
CPGMAC_SL2 RX Maximum Length Register
0x4A10 0754
SL2_BOFFTEST
CPGMAC_SL2 Backoff Test Register
0x4A10 0758
SL2_RX_PAUSE
CPGMAC_SL2 Receive Pause Timer Register
0x4A10 075C
SL2_TX_PAUSE
CPGMAC_SL2 Transmit Pause Timer Register
0x4A10 0760
SL2_EMCONTROL
CPGMAC_SL2 Emulation Control
0x4A10 0764
SL2_RX_PRI_MAP
CPGMAC_SL2 Rx Pkt Priority to Header Priority Mapping Register
0x4A10 0768 - 0x4A10 07FF
–
0x4A10 0800 - 0x4A10 08FF
see Table 8-27
Reserved
0x4A10 0900
IDVER
Subsystem ID Version Register
0x4A10 0904
SOFT_RESET
Subsystem Soft Reset Register
0x4A10 0908
CONTROL
Subsystem Control Register
0x4A10 090C
INT_CONTROL
Subsystem Interrupt Control
0x4A10 0910
C0_RX_THRESH_EN
0x4A10 0914
C0_RX_EN
Subsystem Core 0 Receive Interrupt Enable Register
0x4A10 0918
C0_TX_EN
Subsystem Core 0 Transmit Interrupt Enable Register
0x4A10 091C
C0_MISC_EN
0x4A10 0920
C1_RX_THRESH_EN
0x4A10 0924
C1_RX_EN
Subsystem Core 1 Receive Interrupt Enable Register
0x4A10 0928
C1_TX_EN
Subsystem Core 1 Transmit Interrupt Enable Register
MDIO Registers
Subsystem Core 0 Receive Threshold Int Enable Register
Subsystem Core 0 Misc Interrupt Enable Register
Subsystem Core 1 Receive Threshold Int Enable Register
0x4A10 092C
C1_MISC_EN
0x4A10 0930
C2_RX_THRESH_EN
0x4A10 0934
C2_RX_EN
Subsystem Core 2 Receive Interrupt Enable Register
Subsystem Core 2 Transmit Interrupt Enable Register
0x4A10 0938
C2_TX_EN
0x4A10 093C
C2_MISC_EN
0x4A10 0940
C0_RX_THRESH_STAT
0x4A10 0944
C0_RX_STAT
Subsystem Core 1 Misc Interrupt Enable Register
Subsystem Core 2 Receive Threshold Int Enable Register
Subsystem Core 2 Misc Interrupt Enable Register
Subsystem Core 0 Rx Threshold Masked Int Status Register
Subsystem Core 0 Rx Interrupt Masked Int Status Register
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
241
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-14. Ethernet MAC Switch Registers (continued)
ARM/L3 MASTERS
EMAC HEX
ADDRESS RANGE
ACRONYM
REGISTER NAME
0x4A10 0948
C0_TX_STAT
0x4A10 094C
C0_MISC_STAT
Subsystem Core 0 Tx Interrupt Masked Int Status Register
Subsystem Core 0 Misc Interrupt Masked Int Status Register
0x4A10 0950
C1_RX_THRESH_STAT
Subsystem Core 1 Rx Threshold Masked Int Status Register
0x4A10 0954
C1_RX_STAT
Subsystem Core 1 Receive Masked Interrupt Status Register
0x4A10 0958
C1_TX_STAT
Subsystem Core 1 Transmit Masked Interrupt Status Register
0x4A10 095C
C1_MISC_STAT
0x4A10 0960
C2_RX_THRESH_STAT
Subsystem Core 2 Rx Threshold Masked Int Status Register
0x4A10 0964
C2_RX_STAT
Subsystem Core 2 Receive Masked Interrupt Status Register
0x4A10 0968
C2_TX_STAT
Subsystem Core 2 Transmit Masked Interrupt Status Register
0x4A10 096C
C2_MISC_STAT
0x4A10 0970
C0_RX_IMAX
Subsystem Core 0 Receive Interrupts Per Millisecond
0x4A10 0974
C0_TX_IMAX
Subsystem Core 0 Transmit Interrupts Per Millisecond
Subsystem Core 1 Misc Masked Interrupt Status Register
Subsystem Core 2 Misc Masked Interrupt Status Register
0x4A10 0978
C1_RX_IMAX
Subsystem Core 1 Receive Interrupts Per Millisecond
0x4A10 097C
C1_TX_IMAX
Subsystem Core 1 Transmit Interrupts Per Millisecond
0x4A10 0980
C2_RX_IMAX
Subsystem Core 2 Receive Interrupts Per Millisecond
0x4A10 0984
C2_TX_IMAX
Subsystem Core 2 Transmit Interrupts Per Millisecond
0x4A10 2000 -0x4A10 3FFF
CPPI_RAM
(3)
242
CPPI RAM (3)
Denotes CPPI 3.0 registers.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
8.6.2
8.6.2.1
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
EMAC Electrical Data/Timing
EMAC MII and GMII Electrical Data/Timing
Table 8-15. Timing Requirements for EMAC[x]_MRCLK - [G]MII Operation
(see Figure 8-9)
OPP100/120/166
1000 Mbps (1 Gbps)
(GMII Only)
NO.
MIN
1
tc(MRCLK)
Cycle time, EMAC[x]_MRCLK
2
tw(MRCLKH)
3
4
MAX
100 Mbps
MIN
10 Mbps
MAX
MIN
UNIT
MAX
8
40
400
ns
Pulse duration,
EMAC[x]_MRCLK high
2.8
14
140
ns
tw(MRCLKL)
Pulse duration,
EMAC[x]_MRCLK low
2.8
14
140
ns
tt(MRCLK)
Transition time,
EMAC[x]_MRCLK
1
3
3
ns
4
1
3
2
EMAC[x]_MRCLK
4
Figure 8-9. EMAC[x]_MRCLK Timing (EMAC Receive) - [G]MII Operation
Table 8-16. Timing Requirements for EMAC[x]_MTCLK - [G]MII Operation
(see Figure 8-14)
OPP100/120/166
1000 Mbps (1 Gbps)
(GMII Only)
NO.
MIN
1
tc(MTCLK)
Cycle time, EMAC[x]_MTCLK
2
MAX
100 Mbps
MIN
10 Mbps
MAX
MIN
UNIT
MAX
8
40
400
ns
tw(MTCLKH)
Pulse duration,
EMAC[x]_MTCLK high
2.8
14
140
ns
3
tw(MTCLKL)
Pulse duration,
EMAC[x]_MTCLK low
2.8
14
140
ns
4
tt(MTCLK)
Transition time,
EMAC[x]_MTCLK
1
3
3
4
1
2
ns
3
EMAC[x]_MTCLK
4
Figure 8-10. EMAC[x]_MTCLK Timing (EMAC Transmit) - [G]MII Operation
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
243
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-17. Timing Requirements for EMAC [G]MII Receive 10/100/1000 Mbit/s
(see Figure 8-11)
OPP100/120/166
1000 Mbps (1
Gbps)
NO.
MIN
100/10 Mbps
MAX
MIN
UNIT
MAX
tsu(MRXD-MRCLK)
1
tsu(MRXDV-MRCLK)
Setup time, receive selected signals valid before
EMAC[1:0]_MRCLK
2
8
ns
Hold time, receive selected signals valid after
EMAC[1:0]_MRCLK
0
8
ns
tsu(MRXER-MRCLK)
th(MRCLK-MRXD)
2
th(MRCLK-MRXDV)
th(MRCLK-MRXER)
1
2
EMAC[x]_MRCLK (Input)
EMAC[x]_MRXD3−EMAC[x]_MRXD0,
EMAC[x]_MRXDV, EMAC[x]_MRXER (Inputs)
Figure 8-11. EMAC Receive Interface Timing [G]MII Operation
Table 8-18. Switching Characteristics Over Recommended Operating Conditions for EMAC [G]MII
Transmit 10/100 Mbits/s
(see Figure 8-12)
OPP100/120/166
NO.
1
PARAMETER
td(MTXCLK-MTXD)
td(MTCLK-MTXEN)
100/10 Mbps
Delay time, EMAC[x]_MTCLK to transmit selected signals valid
UNIT
MIN
MAX
2.5
25
ns
Table 8-19. Switching Characteristics Over Recommended Operating Conditions for EMAC [G]MII
Transmit 1000 Mbits/s
(see Figure 8-12)
OPP100/120/166
NO.
1
PARAMETER
td(GMTCLK-MTXD)
1000 Mbps (1 Gbps)
Delay time, EMAC[x]_GMTCLK to transmit selected signals valid
td(GMTCLK-MTXEN)
UNIT
MIN
MAX
0
5
ns
1
EMAC[x]_MTCLK (Input)
EMAC[x]_MTXD3−EMAC[x]_MTXD0,
EMAC[x]_MTXEN (Outputs)
Figure 8-12. EMAC Transmit Interface Timing [G]MII Operation
244
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
8.6.2.2
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
EMAC RMII Electrical Data/Timing
Table 8-20. Timing Requirements for EMAC[x]_RMREFCLK - RMII Operation
(see Figure 8-13)
OPP100/120/166
NO.
MIN
MAX
UNIT
1
tc(RMREFCLK)
Cycle time, EMAC[x]_RMREFCLK
19.999
20.001
ns
2
tw(RMREFCLKH)
Pulse duration, EMAC[x]_RMREFCLK high
7
13
ns
3
tw(RMREFCLKL)
Pulse duration, EMAC[x]_RMREFCLK low
7
13
ns
4
tt(RMREFCLK)
Transition time, EMAC[x]_RMREFCLK
3
ns
1
2
4
RMREFCLK
(Input)
3
4
Figure 8-13. RMREFCLK Timing RMII Operation
Table 8-21. Timing Requirements for EMAC RMII Receive
(see Figure 8-13)
OPP100/120/166
NO.
MIN
UNIT
MAX
tsu(RMRXD-RMREFCLK)
1
tsu(RMCRSDV-RMREFCLK)
Setup time, receive selected signals valid before
EMAC[x]_RMREFCLK
4
ns
Hold time, receive selected signals valid after
EMAC[x]_RMREFCLK
2
ns
tsu(RMRXER-RMREFCLK)
th(RMREFCLK-RMRXD)
2
th(RMREFCLK-RMCRSDV)
th(RMREFCLK-RMRXER)
1
2
RMREFCLK
RMRXD1−RMRXD0,
RMCRSDV, RMRXER (inputs)
Figure 8-14. EMAC Receive Interface Timing RMII Operation
Table 8-22. Switching Characteristics Over Recommended Operating Conditions for EMAC RMII Transmit
10/100 Mbits/s
(see Figure 8-15)
NO.
PARAMETER
OPP100/120/166
MIN
MAX
1
td(RMREFCLK-RMTXD)
Delay time, EMAC[x]_RMREFCLK high to EMAC[x]_RMTXD[x]
valid
2.5
13
2
tdd(RMREFCLK-RMTXEN)
Delay time, EMAC[x]_RMREFCLK high to EMAC[x]_RMTXEN
valid
2.5
13
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
UNIT
ns
245
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
1
RMREFCLK
RMTXD1−RMTXD0,
RMTXEN (Outputs)
Figure 8-15. EMAC Transmit Interface Timing RMII Operation
8.6.2.3
EMAC RGMII Electrical Data/Timing
Table 8-23. Timing Requirements for EMAC[x]_RGRXC - RGMII Operation
(see Figure 8-16)
OPP100/120/166
NO.
10 Mbps
1
2
3
4
246
tc(RGRXC)
tw(RGRXCH)
tw(RGRXCL)
tt(RGRXC)
Cycle time, EMAC[x]_RGRXC
Pulse duration, EMAC[x]_RGRXC high
Pulse duration, EMAC[x]_RGRXC low
Transition time, EMAC[x]_RGRXC
Peripheral Information and Timings
MIN
MAX
360
440
100 Mbps
36
44
1000 Mbps
7.2
8.8
10 Mbps
0.40*tc(RGRXC)
0.60*tc(RGRXC)
100 Mbps
0.40*tc(RGRXC)
0.60*tc(RGRXC)
1000 Mbps
0.45*tc(RGRXC)
0.55*tc(RGRXC)
10 Mbps
0.40*tc(RGRXC)
0.60*tc(RGRXC)
100 Mbps
0.40*tc(RGRXC)
0.60*tc(RGRXC)
1000 Mbps
0.45*tc(RGRXC)
0.55*tc(RGRXC)
10 Mbps
0.75
100 Mbps
0.75
1000 Mbps
0.75
UNIT
ns
ns
ns
ns
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-24. Timing Requirements for EMAC RGMII Input Receive for 10/100/1000 Mbps (1)
(see Figure 8-16)
OPP100/120/166
NO.
MIN
tsu(RGRXD-
5
RGRXCH)
th(RGRXCH-
6
RGRXD)
(1)
MAX
UNIT
Setup time, receive selected signals valid before EMAC[x]_RGRXC (at device)
high/low
1.0
ns
Hold time, receive selected signals valid after EMAC[x]_RGRXC (at device)
high/low
1.0
ns
For RGMII, receive selected signals include: EMAC[x]_RGRXD[3:0] and EMAC[x]_RGRXCTL.
1
4
2
4
3
EMAC[x]_RGRXC
(A)
(at device)
5
1st Half-byte
6
2nd Half-byte
EMAC[x]_RGRXD[3:0]
EMAC[x]_RGRXCTL
A.
B.
(B)
(B)
RGRXD[3:0]
RGRXD[7:4]
RXDV
RXERR
EMAC[x]_RGRXC must be externally delayed relative to the data and control pins. The internal delay can be enabled
or disabled via the EMAC RGMIIx_ID_MODE register.
Data and control information is received using both edges of the clocks. EMAC[x]_RGRXD[3:0] carries data bits 3-0
on the rising edge of EMAC[x]_RGRXC and data bits 7-4 on the falling edge of EMAC[x]_RGRXC. Similarly,
EMAC[x]_RGRXCTL carries RXDV on rising edge of EMAC[x]_RGRXC and RXERR on falling edge of
EMAC[x]_RGRXC.
Figure 8-16. EMAC Receive Interface Timing [RGMII Operation]
Table 8-25. Switching Characteristics Over Recommended Operating Conditions for RGTXC - RGMII
Operation for 10/100/1000 Mbit/s
(see Figure 8-17)
OPP100/120/166
NO.
1
2
3
4
MIN
tc(RGTXC)
tw(RGTXCH)
tw(RGTXCL)
tt(RGTXC)
Cycle time, EMAC[x]_RGTXC
Pulse duration, EMAC[x]_RGTXC high
Pulse duration, EMAC[x]_RGTXC low
Transition time, EMAC[x]_RGTXC
UNIT
MAX
10 Mbps
360
100 Mbps
36
440
44
1000 Mbps
7.2
8.8
10 Mbps
0.40*tc(RGTXC)
0.60*tc(RGTXC)
100 Mbps
0.40*tc(RGTXC)
0.60*tc(RGTXC)
1000 Mbps
0.45*tc(RGTXC)
0.55*tc(RGTXC)
10 Mbps
0.40*tc(RGTXC)
0.60*tc(RGTXC)
100 Mbps
0.40*tc(RGTXC)
0.60*tc(RGTXC)
1000 Mbps
0.45*tc(RGTXC)
0.55*tc(RGTXC)
10 Mbps
0.75
100 Mbps
0.75
1000 Mbps
0.75
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
ns
ns
ns
ns
247
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-26. Switching Characteristics Over Recommended Operating Conditions for EMAC RGMII
Transmit (1)
(see Figure 8-17)
NO.
tsu(RGTXD-
5
RGTXCH)
th(RGTXCH-
6
RGTXD)
tsk(RGTXD-
7
RGTXCH)
(1)
OPP100/120/166
PARAMETER
MIN
MAX
UNIT
Setup time, transmit selected signals valid before
EMAC[x]_RGTXC (at device) high/low
Internal delay enabled
1.2
ns
Hold time, transmit selected signals valid after
EMAC[x]_RGTXC (at device) high/low
Internal delay enabled
1.2
ns
Transmit selected signals to EMAC[x]_RGTXC (at device)
output skew
Internal delay disabled
-0.5
0.5
ns
For RGMII, transmit selected signals include: EMAC[x]_RGTXD[3:0] and EMAC[x]_RGTXCTL.
1
4
2
4
3
(A)
EMAC[x]_RGTXC (at device)
[internal delay enabled]
5
(A)
EMAC[x]_RGTXC (at device)
[internal delay disabled]
7
(B)
1st Half-byte
EMAC[x]_RGTXD[3:0]
2nd Half-byte
6
(B)
EMAC[x]_RGTXCTL
A.
B.
TXEN
TXERR
RGTXC is delayed internally before being driven to the EMAC[x]_RGTXC pin. The internal delay can be enabled or
disabled via the EMAC RGMIIx_ID_MODE register.
Data and control information is transmitted using both edges of the clocks. EMAC[x]_RGTXD[3:0] carries data bits 3-0
on the rising edge of EMAC[x]_RGTXC and data bits 7-4 on the falling edge of EMAC[x]_RGTXC. Similarly,
EMAC[x]_RGTXCTL carries TXEN on rising edge of EMAC[x]_RGTXC and TXERR of falling edge of
EMAC[x]_RGTXC.
Figure 8-17. EMAC Transmit Interface Timing [RGMII Operation]
248
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
8.6.3
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Management Data Input/Output (MDIO)
The Management Data Input/Output (MDIO) module continuously polls all 32 MDIO addresses in order to
enumerate all PHY devices in the system.
The MDIO module implements the 802.3 serial management interface to interrogate and control Ethernet
PHYs using a shared two-wire bus. Host software uses the MDIO module to configure the autonegotiation parameters of each PHY attached to the EMAC SW, retrieve the negotiation results, and
configure required parameters in the EMAC SW module for correct operation. The module is designed to
allow almost transparent operation of the MDIO interface, with very little maintenance from the core
processor. A single MDIO interface is pinned out to control the PHY configuration and status monitoring.
Multiple external PHYs can be controlled by the MDIO interface.
For more detailed information on the MDIO peripheral, see the 3PSW Ethernet Subsystem chapter of the
TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
8.6.3.1
MDIO Peripheral Register Descriptions
Table 8-27. MDIO Registers
HEX ADDRESS
8.6.3.2
ACRONYM
REGISTER NAME
0x4A10 0800
VERSION
MDIO Version
0x4A10 0804
CONTROL
MDIO Control
0x4A10 0808
ALIVE
PHY Alive Status
0x4A10 080C
LINK
PHY Link Status
0x4A10 0810
LINKINTRAW
0x4A10 0814
LINKINTMASKED
0x4A10 0818 - 0x4A10 081C
-
MDIO Link Status Change Interrupt (Unmasked)
MDIO Link Status Change Interrupt (Masked)
Reserved
0x4A10 0820
USERINTRAW
0x4A10 0824
USERINTMASKED
MDIO User Command Complete Interrupt (Unmasked)
MDIO User Command Complete Interrupt (Masked)
0x4A10 0828
USERINTMASKSET
MDIO User Command Complete Interrupt Mask Set
0x4A10 082C
USERINTMASKCLEAR
0x4A10 0830 - 0x4A10 087C
-
MDIO User Command Complete Interrupt Mask Clear
0x4A10 0880
USERACCESS0
MDIO User Access 0
0x4A10 0884
USERPHYSEL0
MDIO User PHY Select 0
Reserved
0x4A10 0888
USERACCESS1
MDIO User Access 1
0x4A10 088C
USERPHYSEL1
MDIO User PHY Select 1
0x4A10 0990 - 0x4A10 08FF
-
Reserved
MDIO Electrical Data/Timing
Table 8-28. Timing Requirements for MDIO Input
(see Figure 8-18)
OPP100/122/166
NO.
1
MIN
MAX
UNIT
tc(MDCLK)
Cycle time, MDCLK
400
ns
tw(MDCLK)
Pulse duration, MDCLK high or low
180
ns
4
tsu(MDIO-MDCLKH)
Setup time, MDIO data input valid before MDCLK high
20
ns
5
th(MDCLKH-MDIO)
Hold time, MDIO data input valid after MDCLK high
0
ns
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
249
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
1
MDCLK
4
5
MDIO
(input)
Figure 8-18. MDIO Input Timing
Table 8-29. Switching Characteristics Over Recommended Operating Conditions for MDIO Output
(see Figure 8-19)
NO.
7
OPP100/122/1166
PARAMETER
td(MDCLKL-MDIO)
MIN
Delay time, MDCLK low to MDIO data output valid
MAX
100
UNIT
ns
1
MDCLK
7
MDIO
(output)
Figure 8-19. MDIO Output Timing
250
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
8.7
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
General-Purpose Input/Output (GPIO)
The GPIO peripheral provides general-purpose pins that can be configured as either inputs
When configured as an output, a write to an internal register controls the state driven on the
When configured as an input, the state of the input is detectable by reading the state of
register. In addition, the GPIO peripheral can produce CPU interrupts in different interrupt
modes. The GPIO peripheral provides generic connections to external devices.
or outputs.
output pin.
an internal
generation
The device contains four GPIO modules and each GPIO module is made up of 32 identical channels.
The device GPIO peripheral supports the following:
• Up to 128 1.8-V/3.3-V GPIO pins, GP0[0:31], GP1[0:31], GP2[0:31], and GP3[0:31] (the exact number
available varies as a function of the device configuration). Each channel can be configured to be used
in the following applications:
– Data input/output
– Keyboard interface with a de-bouncing cell
– Synchronous interrupt generation (in active mode) upon the detection of external events (signal
transitions and/or signal levels).
• Synchronous interrupt requests from each channel are processed by four identical interrupt generation
sub-modules to be used independently by the ARM, DSP, or Media Controller. Interrupts can be
triggered by rising and/or falling edge, specified for each interrupt-capable GPIO signal.
• Shared registers can be accessed through "Set and Clear" protocol. Software writes 1 to
corresponding bit position or positions to set or to clear the GPIO signal. This allows multiple software
processes to toggle GPIO output signals without critical section protection (disable interrupts, program
GPIO, re-enable interrupts, to prevent context switching to another process during GPIO
programming).
• Separate input/output registers.
• Output register in addition to set/clear so that, if preferred by software, some GPIO output signals can
be toggled by direct write to the output register.
• Output register, when read, reflects output drive status. This, in addition to the input register reflecting
pin status and open-drain I/O cell, allows wired logic to be implemented.
For more detailed information on GPIOs, see the General-Purpose I/O (GPIO) Interface chapter of the
TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
8.7.1
GPIO Peripheral Register Descriptions
Table 8-30. GPIO Registers
HEX ADDRESS
GPIO0
GPIO1
GPIO2
GPIO3
ACRONYM
0x4803 2000
0x4804 C000
0x481A C000
0x481A E000
0x4803 2010
0x4804 C010
0x481A C010
0x481A E010
0x4803 2020
0x4804 C020
0x481A C020
0x481A E020
GPIO_EOI
0x4803 2024
0x4804 C024
0x481A C024
0x481A E024
GPIO_IRQSTATUS
_RAW_0
Status Raw for Interrupt 1
0x4803 2028
0x4804 C028
0x481A C028
0x481A E028
GPIO_IRQSTATUS
_RAW_1
Status Raw for Interrupt 2
0x4803 202C
0x4804 C02C
0x481A C02C
0x481A E02C
GPIO_IRQSTATUS
_0
Status for Interrupt 1
0x4803 2030
0x4804 C030
0x481A C030
0x481A E030
GPIO_IRQSTATUS
_1
Status for Interrupt 2
0x4803 2034
0x4804 C034
0x481A C034
0x481A E034
GPIO_IRQSTATUS
_SET_0
Enable Set for Interrupt 1
GPIO_REVISION
REGISTER NAME
GPIO Revision
GPIO_SYSCONFIG System Configuration
End of Interrupt
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
251
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-30. GPIO Registers (continued)
HEX ADDRESS
GPIO0
GPIO1
GPIO2
GPIO3
ACRONYM
0x4803 2038
0x4804 C038
0x481A C038
0x481A E038
GPIO_IRQSTATUS
_SET_1
Enable Set for Interrupt 2
0x4803 203C
0x4804 C03C
0x481A C03C
0x481A E03C
GPIO_IRQSTATUS
_CLR_0
Enable Clear for Interrupt 1
0x4803 2040
0x4804 C040
0x481A C040
0x481A E040
GPIO_IRQSTATUS
_CLR_1
Enable Clear for Interrupt 2
0x4803 2044
0x4804 C044
0x481A C044
0x481A E044
GPIO_IRQWAKEN_ Wakeup Enable for Interrupt
0
1
0x4803 2048
0x4804 C048
0x481A C048
0x481A E048
GPIO_IRQWAKEN_ Wakeup Enable for Interrupt
1
2
0x4803 2114
0x4804 C114
0x481A C114
0x481A E114
GPIO_SYSSTATUS System Status
0x4803 2130
0x4804 C130
0x481A C130
0x481A E130
GPIO_CTRL
Module Control
0x4803 2134
0x4804 C134
0x481A C134
0x481A E134
GPIO_OE
Output Enable
0x4803 2138
0x4804 C138
0x481A C138
0x481A E138
GPIO_DATAIN
0x4803 213C
0x4804 C13C
0x481A C13C
0x481A E13C
GPIO_DATAOUT
0x4803 2140
0x4804 C140
0x481A C140
0x481A E140
GPIO_LEVELDETE
CT0
Detect Low Level
0x4803 2144
0x4804 C144
0x481A C144
0x481A E144
GPIO_LEVELDETE
CT1
Detect High Level
0x4803 2148
0x4804 C148
0x481A C148
0x481A E148
GPIO_RISINGDETE Detect Rising Edge
CT
0x4803 214C
0x4804 C14C
0x481A C14C
0x481A E14C
GPIO_FALLINGDET Detect Falling Edge
ECT
0x4803 2150
0x4804 C150
0x481A C150
0x481A E150
GPIO_DEBOUNCE
NABLE
0x4803 2154
0x4804 C154
0x481A C154
0x481A E154
GPIO_DEBOUNCIN Debouncing Value
GTIME
0x4803 2190
0x4804 C190
0x481A C190
0x481A E190
GPIO_CLEARDATA Clear Data Output
OUT
0x4803 2194
0x4804 C194
0x481A C194
0x481A E194
GPIO_SETDATAOU Set Data Output
T
252
Peripheral Information and Timings
REGISTER NAME
Data Input
Data Output
Debouncing Enable
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
8.7.2
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
GPIO Electrical Data/Timing
Table 8-31. Timing Requirements for GPIO Inputs
(see Figure 8-20)
OPP100/122/166
NO.
1
tw(GPIH)
2
(1)
MIN
tw(GPIL)
Pulse duration, GPx[31:0] input high
Pulse duration, GPx[31:0] input low
MAX
UNIT
12P (1)
ns
(1)
ns
12P
P = Module clock.
Table 8-32. Switching Characteristics Over Recommended Operating Conditions for GPIO Outputs
(see Figure 8-20)
NO.
3
4
(1)
OPP100/122/166
PARAMETER
tw(GPOH)
tw(GPOL)
MIN
Pulse duration, GPx[31:0] output high
Pulse duration, GPx[31:0] output low
MAX
UNIT
36P-8 (1)
ns
(1)
ns
36P-8
P = Module clock.
2
GPx[31:0]
input
1
4
3
GPx[31:0]
output
Figure 8-20. GPIO Port Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
253
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.8
www.ti.com
General-Purpose Memory Controller (GPMC) and Error Location Module (ELM)
The GPMC is a device memory controller used to provide a glueless interface to external memory devices
such as NOR Flash, NAND Flash (with BCH and Hamming Error Code Detection for 8-bit or 16-bit NAND
Flash), SRAM, and Pseudo-SRAM. The GPMC includes flexible asynchronous protocol control for
interface to SRAM-like memories and custom logic (FPGA, CPLD, ASICs, etc.).
Other supported features include:
• 8-/16-bit wide multiplexed address/data bus
• 512 MBytes maximum addressing capability divided among up to eight chip selects
• Non-multiplexed address/data mode
• Pre-fetch and write posting engine associated with system DMA to get full performance from NAND
device with minimum impact on NOR/SRAM concurrent access.
The device also contains an Error Locator Module (ELM) which is used to extract error addresses from
syndrome polynomials generated using a BCH algorithm. Each of these polynomials gives a status of the
read operations for a 512 bytes block from a NAND flash and its associated BCH parity bits, plus
optionally spare area information. The ELM has the following features:
• 4-bit, 8-bit and 16-bit per 512byte block error location based on BCH algorithms
• Eight simultaneous processing contexts
• Page-based and continuous modes
• Interrupt generation on error location process completion
– When the full page has been processed in page mode
– For each syndrome polynomial in continuous mode
254
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
8.8.1
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
GPMC and ELM Peripherals Register Descriptions
Table 8-33. GPMC Registers
HEX ADDRESS
REGISTER NAME
0x5000 0000
GPMC_REVISION
0x5000 0010
GPMC_SYSCONFIG
System Configuration
0x5000 0014
GPMC_SYSSTATUS
System Status
0x5000 0018
GPMC_IRQSTATUS
Status for Interrupt
0x5000 001C
GPMC_IRQENABLE
Interrupt Enable
0x5000 0040
GPMC_TIMEOUT_CONTROL
0x5000 0044
GPMC_ERR_ADDRESS
0x5000 0048
GPMC_ERR_TYPE
0x5000 0050
GPMC_CONFIG
GPMC Global Configuration
0x5000 0054
GPMC_STATUS
GPMC Revision
GPMC Global Status
Timeout Counter Start Value
Error Address
Error Type
(1)
GPMC_CONFIG1_0 GPMC_CONFIG1_7
Parameter Configuration 1_0-7
0x5000 0064 + (0x0000 0030 * i) (1)
GPMC_CONFIG2_0 GPMC_CONFIG2_7
Parameter Configuration 2_0-7
0x5000 0068 + (0x0000 0030 * i) (1)
GPMC_CONFIG3_0 GPMC_CONFIG3_7
Parameter Configuration 3_0-7
0x5000 006C + (0x0000 0030 * i) (1)
GPMC_CONFIG4_0 GPMC_CONFIG4_7
Parameter Configuration 4_0-7
0x5000 0070 + (0x0000 0030 * i) (1)
GPMC_CONFIG5_0 GPMC_CONFIG5_7
Parameter Configuration 5_0-7
0x5000 0074 + (0x0000 0030 * i) (1)
GPMC_CONFIG6_0 GPMC_CONFIG6_7
Parameter Configuration 6_0-7
0x5000 0078 + (0x0000 0030 * i) (1)
GPMC_CONFIG7_0 GPMC_CONFIG7_7
Parameter Configuration 7_0-7
0x5000 007C + (0x0000 0030 * i) (1)
GPMC_NAND_COMMAND_0 GPMC_NAND_COMMAND_7
NAND Command 0-7
0x5000 0080 + (0x0000 0030 * i) (1)
GPMC_NAND_ADDRESS_0 GPMC_NAND_ADDRESS_7
NAND Address 0-7
0x5000 0084 + (0x0000 0030 * i) (1)
GPMC_NAND_DATA_0 GPMC_NAND_DATA_7
0x5000 01E0
GPMC_PREFETCH_CONFIG1
Prefetch Configuration 1
0x5000 01E4
GPMC_PREFETCH_CONFIG2
Prefetch Configuration 2
0x5000 0060 + (0x0000 0030 * i)
(1)
(2)
ACRONYM
NAND Data 0-7
0x5000 01EC
GPMC_PREFETCH_CONTROL
Prefetch Control
0x5000 01F0 (1)
GPMC_PREFETCH_STATUS
Prefetch Status
0x5000 01F4
GPMC_ECC_CONFIG
ECC Configuration
0x5000 01F8
GPMC_ECC_CONTROL
0x5000 01FC
GPMC_ECC_SIZE_CONFIG
ECC Control
0x5000 0200 + (0x0000 0004 * j) (2)
GPMC_ECC0_RESULT GPMC_ECC8_RESULT
0x5000 0240 + (0x0000 0010 * i) (1)
GPMC_BCH_RESULT0_0 GPMC_BCH_RESULT0_7
BCH Result 0_0-7
0x5000 0244 + (0x0000 0010 * i) (1)
GPMC_BCH_RESULT1_0 GPMC_BCH_RESULT1_7
BCH Result 1_0-7
0x5000 0248 + (0x0000 0010 * i) (1)
GPMC_BCH_RESULT2_0 GPMC_BCH_RESULT2_7
BCH Result 2_0-7
0x5000 024C + (0x0000 0010 * i) (1)
GPMC_BCH_RESULT3_0 GPMC_BCH_RESULT3_7
BCH Result 3_0-7
0x5000 0300 + (0x0000 0010 * i) (1)
GPMC_BCH_RESULT4_0 GPMC_BCH_RESULT4_7
BCH Result 4_0-7
ECC Size Configuration
ECC0-8 Result
i = 0 to 7
j = 0 to 8
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
255
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-33. GPMC Registers (continued)
256
HEX ADDRESS
ACRONYM
REGISTER NAME
0x5000 0304 + (0x0000 0010 * i) (1)
GPMC_BCH_RESULT5_0 GPMC_BCH_RESULT5_7
BCH Result 5_0-7
0x5000 0308 + (0x0000 0010 * i) (1)
GPMC_BCH_RESULT6_0 GPMC_BCH_RESULT6_7
BCH Result 6_0-7
0x5000 02D0
GPMC_BCH_SWDATA
Peripheral Information and Timings
BCH Data
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
8.8.2
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
GPMC Electrical Data/Timing
8.8.2.1
GPMC/NOR Flash Interface Synchronous Mode Timing (Non-Multiplexed and Multiplexed Modes)
Table 8-34. Timing Requirements for GPMC/NOR Flash Interface - Synchronous Mode
(see Figure 8-21, Figure 8-22, Figure 8-23 for Non-Multiplexed Modes)
(see Figure 8-24, Figure 8-25, Figure 8-26 for Multiplexed Modes)
OPP100/120/166
NO.
MIN
MAX
UNIT
13
tsu(DV-CLKH)
Setup time, read GPMC_D[15:0] valid before GPMC_CLK high
4
ns
14
th(CLKH-DV)
Hold time, read GPMC_D[15:0] valid after GPMC_CLK high
3
ns
22
tsu(WAITV-CLKH)
Setup time, GPMC_WAIT[x] valid before GPMC_CLK high
4
ns
23
th(CLKH-WAITV)
Hold time, GPMC_WAIT[x] valid after GPMC_CLK high
3
ns
Table 8-35. Switching Characteristics Over Recommended Operating Conditions for GPMC/NOR Flash
Interface - Synchronous Mode
(see Figure 8-21, Figure 8-22, Figure 8-23 for Non-Multiplexed Modes)
(see Figure 8-24, Figure 8-25, Figure 8-26 for Multiplexed Modes)
NO
.
1
2
3
4
OPP100/120/166
PARAMETER
MIN
20 (1)
Cycle time, output clock GPMC_CLK period
tw(CLKH)
Pulse duration, output clock GPMC_CLK high
0.5P (2)
tw(CLKL)
Pulse duration, output clock GPMC_CLK low
0.5P (2)
td(CLKH-nCSV)
Delay time, GPMC_CLK rising edge to GPMC_CS[x] transition
F - 3 (3)
F + 6 (3)
ns
E-3
(4)
E+6
(4)
ns
B-6
(5)
B+6
(5)
td(CLKH-nCSIV)
Delay time, GPMC_CLK rising edge to GPMC_CS[x] invalid
td(ADDV-CLK)
Delay time, GPMC_A[27:0] address bus valid to
GPMC_CLK first edge
MUX1 for
GPMC_A[15:0]
td(CLKH-ADDIV)
(1)
(2)
(3)
(4)
(5)
td(nBEV-CLK)
(5)
(5)
GPMC_AD[15:0]
B - 10 (5)
GPMC_AD[15:0]
7
Delay time, GPMC_BE0_CLE, GPMC_BE1 valid to GPMC_CLK first edge
ns
B + 6 (5)
B - 10
MUX1 for
Delay time, GPMC_CLK rising edge to GPMC_A[27:0] GPMC_A[15:0]
GPMC address bus invalid
MUX1/2 for
GPMC_A[27:20]
ns
B - 10 (5)
MUX1/2 for
GPMC_A[27:20]
MUX0 and Non-Multi
Muxed pins
6
UNIT
tc(CLK)
MUX0 and Non-Multi
Muxed pins
5
MAX
B+6
ns
B + 6 (5)
-3
-6
ns
-6
-6
B - 3 (5)
B + 3 (5)
ns
Sync mode can operate at 50 MHz max.
P = GPMC_CLK period.
For nCS falling edge (CS activated):
• For GpmcFCLKDivider = 0:
F = 0.5 * CSExtraDelay * GPMC_FCLK
• For GpmcFCLKDivider = 1:
F = 0.5 * CSExtraDelay * GPMC_FCLK if (ClkActivationTime and CSOnTime are odd) or (ClkActivationTime and CSOnTime are
even)
F = (1 + 0.5 * CSExtraDelay) * GPMC_FCLK otherwise
• For GpmcFCLKDivider = 2:
F = 0.5 * CSExtraDelay * GPMC_FCLK if ((CSOnTime – ClkActivationTime) is a multiple of 3)
F = (1 + 0.5 * CSExtraDelay) * GPMC_FCLK if ((CSOnTime – ClkActivationTime – 1) is a multiple of 3)
F = (2 + 0.5 * CSExtraDelay) * GPMC_FCLK if ((CSOnTime – ClkActivationTime – 2) is a multiple of 3)
For single read: E = (CSRdOffTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK
For burst read: E = (CSRdOffTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK
For burst write: E = (CSWrOffTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK
B = ClkActivationTime * GPMC_FCLK
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
257
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-35. Switching Characteristics Over Recommended Operating Conditions for GPMC/NOR Flash
Interface - Synchronous Mode (continued)
(see Figure 8-21, Figure 8-22, Figure 8-23 for Non-Multiplexed Modes)
(see Figure 8-24, Figure 8-25, Figure 8-26 for Multiplexed Modes)
NO
.
8
OPP100/120/166
PARAMETER
td(CLKH-nBEIV)
Delay time, GPMC_CLK rising edge to GPMC_BE0_CLE, GPMC_BE1 invalid
UNIT
MIN
MAX
D - 3 (6)
D + 3 (6)
ns
(7)
(7)
ns
9
td(CLKH-nADV)
Delay time, GPMC_CLK rising edge to GPMC_ADV_ALE transition
G-3
10
td(CLKH-nADVIV)
Delay time, GPMC_CLK rising edge to GPMC_ADV_ALE invalid
D - 3 (6)
D + 6 (6)
ns
11
td(CLKH-nOE)
Delay time, GPMC_CLK rising edge to GPMC_OE_RE transition
H - 3 (8)
H + 5 (8)
ns
(6)
(7)
(8)
258
G+6
For single read: D = (RdCycleTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK
For burst read: D = (RdCycleTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK
For burst write: D = (WrCycleTime – AccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK
For ADV falling edge (ADV activated):
• Case GpmcFCLKDivider = 0:
G = 0.5 * ADVExtraDelay * GPMC_FCLK
• Case GpmcFCLKDivider = 1:
G = 0.5 * ADVExtraDelay * GPMC_FCLK if (ClkActivationTime and ADVOnTime are odd) or (ClkActivationTime and ADVOnTime are
even)
G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK otherwise
• Case GpmcFCLKDivider = 2:
G = 0.5 * ADVExtraDelay * GPMC_FCLK if ((ADVOnTime – ClkActivationTime) is a multiple of 3)
G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK if ((ADVOnTime – ClkActivationTime – 1) is a multiple of 3)
G = (2 + 0.5 * ADVExtraDelay) * GPMC_FCLK if ((ADVOnTime – ClkActivationTime – 2) is a multiple of 3)
For ADV rising edge (ADV deactivated) in Reading mode:
• Case GpmcFCLKDivider = 0:
G = 0.5 * ADVExtraDelay * GPMC_FCLK
• Case GpmcFCLKDivider = 1:
G = 0.5 * ADVExtraDelay * GPMC_FCLK if (ClkActivationTime and ADVRdOffTime are odd) or (ClkActivationTime and
ADVRdOffTime are even)
G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK otherwise
• Case GpmcFCLKDivider = 2:
G = 0.5 * ADVExtraDelay * GPMC_FCLK if ((ADVRdOffTime – ClkActivationTime) is a multiple of 3)
G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK if ((ADVRdOffTime – ClkActivationTime – 1) is a multiple of 3)
G = (2 + 0.5 * ADVExtraDelay) * GPMC_FCLK if ((ADVRdOffTime – ClkActivationTime – 2) is a multiple of 3)
For ADV rising edge (ADV deactivated) in Writing mode:
• Case GpmcFCLKDivider = 0:
G = 0.5 * ADVExtraDelay * GPMC_FCLK
• Case GpmcFCLKDivider = 1:
G = 0.5 * ADVExtraDelay * GPMC_FCLK if (ClkActivationTime and ADVWrOffTime are odd) or (ClkActivationTime and
ADVWrOffTime are even)
G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK otherwise
• Case GpmcFCLKDivider = 2:
G = 0.5 * ADVExtraDelay * GPMC_FCLK if ((ADVWrOffTime – ClkActivationTime) is a multiple of 3)
G = (1 + 0.5 * ADVExtraDelay) * GPMC_FCLK if ((ADVWrOffTime – ClkActivationTime – 1) is a multiple of 3)
G = (2 + 0.5 * ADVExtraDelay) * GPMC_FCLK if ((ADVWrOffTime – ClkActivationTime – 2) is a multiple of 3)
For OE falling edge (OE activated) / IO DIR rising edge (IN direction) :
• Case GpmcFCLKDivider = 0:
H = 0.5 * OEExtraDelay * GPMC_FCLK
• Case GpmcFCLKDivider = 1:
H = 0.5 * OEExtraDelay * GPMC_FCLK if (ClkActivationTime and OEOnTime are odd) or (ClkActivationTime and OEOnTime are
even)
H = (1 + 0.5 * OEExtraDelay) * GPMC_FCLK otherwise
• Case GpmcFCLKDivider = 2:
H = 0.5 * OEExtraDelay * GPMC_FCLK if ((OEOnTime – ClkActivationTime) is a multiple of 3)
H = (1 + 0.5 * OEExtraDelay) * GPMC_FCLK if ((OEOnTime – ClkActivationTime – 1) is a multiple of 3)
H = (2 + 0.5 * OEExtraDelay) * GPMC_FCLK if ((OEOnTime – ClkActivationTime – 2) is a multiple of 3)
For OE rising edge (OE deactivated):
• Case GpmcFCLKDivider = 0:
H = 0.5 * OEExtraDelay * GPMC_FCLK
• Case GpmcFCLKDivider = 1:
H = 0.5 * OEExtraDelay * GPMC_FCLK if (ClkActivationTime and OEOffTime are odd) or (ClkActivationTime and OEOffTime are
even)
H = (1 + 0.5 * OEExtraDelay) * GPMC_FCLK otherwise
• Case GpmcFCLKDivider = 2:
H = 0.5 * OEExtraDelay * GPMC_FCLK if ((OEOffTime – ClkActivationTime) is a multiple of 3)
H = (1 + 0.5 * OEExtraDelay) * GPMC_FCLK if ((OEOffTime – ClkActivationTime – 1) is a multiple of 3)
H = (2 + 0.5 * OEExtraDelay) * GPMC_FCLK if ((OEOffTime – ClkActivationTime – 2) is a multiple of 3)
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-35. Switching Characteristics Over Recommended Operating Conditions for GPMC/NOR Flash
Interface - Synchronous Mode (continued)
(see Figure 8-21, Figure 8-22, Figure 8-23 for Non-Multiplexed Modes)
(see Figure 8-24, Figure 8-25, Figure 8-26 for Multiplexed Modes)
NO
.
12
PARAMETER
td(CLKH-nOEIV)
Delay time, GPMC_CLK rising edge to GPMC_OE_RE invalid
OPP100/120/166
UNIT
MIN
MAX
E - 3 (4)
E + 5 (4)
ns
(9)
(9)
ns
15
td(CLKH-nWE)
Delay time, GPMC_CLK rising edge to GPMC_WE transition
16
td(CLKH-Data)
Delay time, GPMC_CLK rising edge to GPMC_D[15:0] data bus transition
J - 3 (10)
I-3
J + 3 (10)
I+6
ns
18
td(CLKH-nBE)
Delay time, GPMC_CLK rising edge to GPMC_BE0_CLE, GPMC_BE1 transition
J - 3 (10)
J + 3 (10)
ns
(11)
ns
19
tw(nCSV)
Pulse duration, GPMC_CS[x] low
A
20
tw(nBEV)
Pulse duration, GPMC_BE0_CLE, GPMC_BE1 low
C (12)
ns
21
tw(nADVV)
Pulse duration, GPMC_ADV_ALE low
K (13)
ns
(9)
(10)
(11)
(12)
(13)
For WE falling edge (WE activated):
• Case GpmcFCLKDivider = 0:
I = 0.5 * WEExtraDelay * GPMC_FCLK
• Case GpmcFCLKDivider = 1:
I = 0.5 * WEExtraDelay * GPMC_FCLK if (ClkActivationTime and WEOnTime are odd) or (ClkActivationTime and WEOnTime are
even)
I = (1 + 0.5 * WEExtraDelay) * GPMC_FCLK otherwise
• Case GpmcFCLKDivider = 2:
I = 0.5 * WEExtraDelay * GPMC_FCLK if ((WEOnTime – ClkActivationTime) is a multiple of 3)
I = (1 + 0.5 * WEExtraDelay) * GPMC_FCLK if ((WEOnTime – ClkActivationTime – 1) is a multiple of 3)
I = (2 + 0.5 * WEExtraDelay) * GPMC_FCLK if ((WEOnTime – ClkActivationTime – 2) is a multiple of 3)
For WE rising edge (WE deactivated):
• Case GpmcFCLKDivider = 0:
I = 0.5 * WEExtraDelay * GPMC_FCLK
• Case GpmcFCLKDivider = 1:
I = 0.5 * WEExtraDelay * GPMC_FCLK if (ClkActivationTime and WEOffTime are odd) or (ClkActivationTime and WEOffTime are
even)
I = (1 + 0.5 * WEExtraDelay) * GPMC_FCLK otherwise
• Case GpmcFCLKDivider = 2:
I = 0.5 * WEExtraDelay * GPMC_FCLK if ((WEOffTime – ClkActivationTime) is a multiple of 3)
I = (1 + 0.5 * WEExtraDelay) * GPMC_FCLK if ((WEOffTime – ClkActivationTime – 1) is a multiple of 3)
I = (2 + 0.5 * WEExtraDelay) * GPMC_FCLK if ((WEOffTime – ClkActivationTime – 2) is a multiple of 3)
J = GPMC_FCLK period.
For single read: A = (CSRdOffTime - CSOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK period
For burst read: A = (CSRdOffTime - CSOnTime + (n - 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK period [n
= page burst access number]
For burst write: A = (CSWrOffTime - CSOnTime + (n - 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK period [n
= page burst access number]
For single read: C = RdCycleTime * (TimeParaGranularity + 1) * GPMC_FCLK
For burst read: C = (RdCycleTime + (n – 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK [n = page burst
access number]
For Burst write: C = (WrCycleTime + (n – 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK [n = page burst
access number]
For read: K = (ADVRdOffTime - ADVOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK
For write: K = (ADVWrOffTime - ADVOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
259
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
2
2
1
GPMC_CLK
3
4
19
GPMC_CS[x]
5
GPMC_A[27:0]
Address
7
8
20
GPMC_BE1
7
8
20
GPMC_BE0_CLE
9
9
10
21
GPMC_ADV_ALE
11
12
GPMC_OE
14
13
GPMC_AD[15:0]
D0
23
22
GPMC_WAIT[x]
Figure 8-21. GPMC Non-Multiplexed NOR Flash - Synchronous Single Read (GPMCFCLKDIVIDER = 0)
2
1
2
GPMC_CLK
3
4
19
GPMC_CS[x]
5
GPMC_A[27:0]
Address
8
7
20
Valid
GPMC_BE1
8
7
20
Valid
GPMC_BE0_CLE
9
9
10
21
GPMC_ADV_ALE
11
12
GPMC_OE
14
13
13
13
13
GPMC_D[15:0]
(Non-Multplexed Mode)
D0
23
D1
D2
D3
22
GPMC_WAIT[x]
Figure 8-22. GPMC Non-Multiplexed NOR Flash - 14x16-bit Synchronous Burst Read
(GPMCFCLKDIVIDER = 0)
260
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
2
1
2
GPMC_CLK
3
4
19
GPMC_CS[x]
5
GPMC_A[27:0]
Address
7
18
18
18
GPMC_BE1
18
7
18
18
GPMC_BE0_CLE
9
9
10
21
GPMC_ADV_ALE
15
15
GPMC_WE
GPMC_D[15:0]
(Non-Multiplexed Mode)
16
16
16
D1
D0
23
16
D2
D3
22
GPMC_WAIT[x]
Figure 8-23. GPMC Non-Multiplexed NOR Flash - Synchronous Burst Write (GPMCFCLKDIVIDER = 0)
2
2
1
GPMC_CLK
3
4
19
GPMC_CS[x]
5
GPMC_A[27:16]
Address
7
8
20
GPMC_BE1
7
8
20
GPMC_BE0_CLE
9
9
10
21
GPMC_ADV_ALE
11
12
GPMC_OE
5
6
GPMC_D[15:0]
(Multiplexed Mode)
Address (LSB)
23
13
14
D0
22
GPMC_WAIT[x]
Figure 8-24. GPMC Multiplexed NOR Flash - Synchronous Single Read (GPMCFCLKDIVIDER = 0)
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
261
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
2
1
2
GPMC_CLK
3
4
19
GPMC_CS[x]
5
GPMC_A[27:16]
Address (MSB)
8
7
20
Valid
GPMC_BE1
8
7
20
Valid
GPMC_BE0_CLE
9
9
10
21
GPMC_ADV_ALE
11
12
GPMC_OE
14
13
5
GPMC_D[15:0]
(Multplexed Mode)
13
13
13
6
Address (LSB)
D0
23
D1
D2
D3
22
GPMC_WAIT[x]
Figure 8-25. GPMC Multiplexed NOR Flash - 14x16-bit Synchronous Burst Read (GPMCFCLKDIVIDER = 0)
2
1
2
GPMC_CLK
3
4
19
GPMC_CS[x]
5
GPMC_A[27:16]
6
Address (MSB)
7
18
18
18
GPMC_BE1
18
7
18
18
GPMC_BE0_CLE
9
9
10
21
GPMC_ADV_ALE
15
15
GPMC_WE
GPMC_D[15:0]
(Multiplexed Mode)
16
6,16
5
Address (LSB)
16
D0
23
D1
16
D2
D3
22
GPMC_WAIT[x]
Figure 8-26. GPMC Non-Multiplexed NOR Flash - Synchronous Burst Write (GPMCFCLKDIVIDER = 0)
8.8.2.2
262
GPMC/NOR Flash Interface Asynchronous Mode Timing (Non-Multiplexed and Multiplexed
Modes)
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-36. Timing Requirements for GPMC/NOR Flash Interface - Asynchronous Mode (1)
(see Figure 8-27, Figure 8-28 for Non-Multiplexed Mode )
(see Figure 8-29, Figure 8-31 for Multiplexed Mode)
OPP100/120/166
NO.
MIN
UNIT
MAX
6
tacc(DAT)
Data maximum access time (GPMC_FCLK cycles)
H (2)
cycles
21
tacc1-pgmode(DAT)
Page mode successive data maximum access time (GPMC_FCLK
cycles)
P (3)
cycles
Page mode first data maximum access time (GPMC_FCLK cycles)
(2)
cycles
22
(1)
(2)
(3)
tacc2-pgmode(DAT)
H
The internal GPMC_FCLK is equal to SYSCLK6, and is nominally 100 MHz or 10 ns. For any additional constraints, see the Clocking
section of this document.
H = AccessTime * (TimeParaGranularity + 1)
P = PageBurstAccessTime * (TimeParaGranularity + 1).
Table 8-37. Switching Characteristics Over Recommended Operating Conditions for GPMC/NOR Flash
Interface - Asynchronous Mode
(see Figure 8-27, Figure 8-28, Figure 8-29, Figure 8-30 for Non-Multiplexed Modes)
(see Figure 8-31, Figure 8-32 for Multiplexed Modes)
NO
.
OPP100/120/166
PARAMETER
MIN
MAX
UNIT
1
tw(nBEV)
Pulse duration, GPMC_BE0_CLE, GPMC_BE1 valid time
N (1)
ns
2
tw(nCSV)
Pulse duration, GPMC_CS[x] low
A (2)
ns
4
td(nCSV-nADVIV)
Delay time, GPMC_CS[x] valid to GPMC_NADV_ALE invalid
B - 2 (3)
B + 4 (3)
ns
C+4
(4)
ns
J+4
(5)
ns
5
10
11
td(nCSV-nOEIV)
td(AV-nCSV)
td(nBEV-nCSV)
C-2
(4)
MUX0 and Non-Multi
Muxed pins
J-2
(5)
MUX1 for
GPMC_A[15:0]
J - 2 (5)
J + 4 (5)
ns
MUX1/2 for
GPMC_A[27:20]
J - 2 (5)
J + 4 (5)
ns
J - 2 (5)
J + 4 (5)
ns
(6)
K + 4 (6)
ns
L + 4 (7)
ns
Delay time, GPMC_CS[x] valid to GPMC_OE_RE invalid (single read)
Delay time, GPMC_A[27:0] address bus valid to
GPMC_CS[x] valid
Delay time, GPMC_BE0_CLE, GPMC_BE1 valid to GPMC_CS[x] valid
13
td(nCSV-nADVV)
Delay time, GPMC_CS[x] valid to GPMC_ADV_ALE valid
K-2
14
td(nCSV-nOEV)
Delay time, GPMC_CS[x] valid to GPMC_OE_RE valid
L - 2 (7)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
For single read: N = RdCycleTime * (TimeParaGranularity + 1) * GPMC_FCLK
For single write: N = WrCycleTime * (TimeParaGranularity + 1) * GPMC_FCLK
For burst read: N = (RdCycleTime + (n - 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK
For burst write: N = (WrCycleTime + (n - 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK
For single read: A = (CSRdOffTime - CSOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK
For single write: A = (CSWrOffTime - CSOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK
For burst read: A = (CSRdOffTime - CSOnTime + (n - 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK
For burst write: A = (CSWrOffTime - CSOnTime + (n - 1) * PageBurstAccessTime) * (TimeParaGranularity + 1) * GPMC_FCLK
= B - nCS Max Delay + nADV Min Delay
For reading: B = ((ADVRdOffTime - CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (ADVExtraDelay - CSExtraDelay)) * GPMC_FCLK
For writing: B = ((ADVWrOffTime - CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (ADVExtraDelay - CSExtraDelay)) * GPMC_FCLK
= C - nCS Max Delay + nOE Min Delay
C = ((OEOffTime - CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (OEExtraDelay - CSExtraDelay)) * GPMC_FCLK
= J - Address Max Delay + nCS Min Delay
J = (CSOnTime * (TimeParaGranularity + 1) + 0.5 * CSExtraDelay) * GPMC_FCLK
= K - nCS Max Delay + nADV Min Delay
K = ((ADVOnTime - CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (ADVExtraDelay - CSExtraDelay)) * GPMC_FCLK
= L - nCS Max Delay + nOE Min Delay
L = ((OEOnTime - CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (OEExtraDelay - CSExtraDelay)) * GPMC_FCLK
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
263
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-37. Switching Characteristics Over Recommended Operating Conditions for GPMC/NOR Flash
Interface - Asynchronous Mode (continued)
(see Figure 8-27, Figure 8-28, Figure 8-29, Figure 8-30 for Non-Multiplexed Modes)
(see Figure 8-31, Figure 8-32 for Multiplexed Modes)
NO
.
17
OPP100/120/166
PARAMETER
tw(AIV)
Pulse duration, GPMC_A[27:0] address bus invalid
between 2 successive R/W accesses
MIN
21
td(nCSV-nOEIV)
tw(AV)
G (8)
ns
MUX1 for
GPMC_A[15:0]
G (8)
ns
MUX1/2 for
GPMC_A[27:20]
G (8)
ns
Delay time, GPMC_CS[x] valid to GPMC_OE_RE invalid (burst read)
Pulse duration, GPMC_A[27:0] address bus valid:
second, third and fourth accesses
G
(8)
I - 2 (9)
ns
MUX1 for
GPMC_A[15:0]
D (10)
ns
MUX1/2 for
GPMC_A[27:20]
D (10)
ns
GPMC_D[15:0]
D (10)
(11)
ns
F + 4 (12)
ns
2.0
ns
(5)
ns
MUX0 and Non-Multi
Muxed pins
2.0
ns
MUX0 and Non-Multi
Muxed pins
2.0
ns
MUX1 for
GPMC_A[15:0]
2.0
ns
MUX1/2 for
GPMC_A[27:20]
2.0
ns
GPMC_D[15:0]
2.0
ns
MUX0 and Non-Multi
Muxed pins
2.0
ns
Delay time, GPMC_CS[x] valid to GPMC_WE valid
E-2
td(nCSV-nWEIV)
Delay time, GPMC_CS[x] valid to GPMC_WE invalid
F - 2 (12)
29
td(nWEV-DV)
Delay time, GPMC_WE valid to GPMC_D[15:0] data bus valid
39
td(DV-nCSV)
Delay time, GPMC_D[15:0] data bus valid to GPMC_CS[x] valid
td(ADVV-AIV)
Delay time, GPMC_ADV_ALE valid to GPMC_D[15:0]
address invalid
td(nOEV-AIV)
td(AIV-ADVV)
Delay time, GPMC_OE_RE valid to GPMC_D[15:0]
address/data busses phase end
Delay time, GPMC_D[15:0] address valid to
GPMC_ADV_ALE invalid
ns
(11)
td(nCSV-nWEV)
38
ns
D (10)
28
37
ns
I + 4 (9)
MUX0 and Non-Multi
Muxed pins
26
30
UNIT
MUX0 and Non-Multi
Muxed pins
GPMC_D[15:0]
19
MAX
J-2
(5)
E+4
J+4
(8)
(9)
G = Cycle2CycleDelay * GPMC_FCLK
= I - nCS Max Delay + nOE Min Delay
I = ((OEOffTime + (n - 1) * PageBurstAccessTime - CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (OEExtraDelay - CSExtraDelay)) *
GPMC_FCLK
(10) D = PageBurstAccessTime * (TimeParaGranularity + 1) * GPMC_FCLK
(11) = E - nCS Max Delay + nWE Min Delay
E = ((WEOnTime - CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (WEExtraDelay - CSExtraDelay)) * GPMC_FCLK
(12) = F - nCS Max Delay + nWE Min Delay
F = ((WEOffTime - CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (WEExtraDelay - CSExtraDelay)) * GPMC_FCLK
264
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
GPMC_FCLK
GPMC_CLK
6
2
GPMC_CS[x]
10
GPMC_A[10:1]
Valid Address
11
1
GPMC_BE1
11
1
GPMC_BE0_CLE
4
13
GPMC_ADV_ALE
5
14
GPMC_OE
GPMC_AD[15:0]
Data In 0
Data In 0
GPMC_WAIT[x]
Figure 8-27. GPMC/Non-Multiplexed NOR Flash - Asynchronous Read - Single Word Timing
GPMC_FCLK
GPMC_CLK
6
6
2
2
GPMC_CS[x]
17
10
10
GPMC_A[10:1]
Address 1
Address 2
11
11
1
1
GPMC_BE1
11
11
1
1
GPMC_BE0_CLE
4
4
13
13
GPMC_ADV_ALE
5
5
14
14
GPMC_OE
GPMC_AD[15:0]
Data Upper
GPMC_WAIT[x]
Figure 8-28. GPMC/Non-Multiplexed NOR Flash - Asynchronous Read - 32-Bit Access Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
265
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
GPMC_FCLK
GPMC_CLK
22
21
21
21
2
GPMC_CS[x]
10
GPMC_A[10:1]
Add1
Add2
Add3
D0
D1
D2
Add0
Add4
11
1
GPMC_BE1
11
1
GPMC_BE0_CLE
13
GPMC_ADV_ALE
19
14
GPMC_OE
GPMC_AD[15:0]
D3
D3
GPMC_WAIT[x]
Figure 8-29. GPMC/Non-Multiplexed Only NOR Flash - Asynchronous Read - Page Mode 4x16-Bit Timing
GPMC_FCLK
GPMC_CLK
2
GPMC_CS[x]
10
GPMC_A[10:1]
Valid Address
11
1
GPMC_BE1
11
1
GPMC_BE0_CLE
4
13
GPMC_ADV_ALE
28
26
GPMC_WE
30
GPMC_AD[15:0]
Data OUT
GPMC_WAIT[x]
Figure 8-30. GPMC/Non-Multiplexed NOR Flash - Asynchronous Write - Single Word Timing
266
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
GPMC_FCLK
GPMC_CLK
2
6
GPMC_CS[x]
10
Address (MSB)
GPMC_A[26:17]
11
1
GPMC_BE1
11
1
GPMC_BE0_CLE
13
4
GPMC_ADV_ALE
5
14
GPMC_OE
GPMC_A[16:1]
GPMC_AD[15:0]
38
30
Address (LSB)
Data IN
Data IN
GPMC_WAIT[x]
Figure 8-31. GPMC/Multiplexed NOR Flash - Asynchronous Read - Single Word Timing
GPMC_FCLK
GPMC_CLK
2
GPMC_CS[x]
10
Address (MSB)
GPMC_A[26:17]
11
1
GPMC_BE1
11
1
GPMC_BE0_CLE
13
4
GPMC_ADV_ALE
28
26
GPMC_WE
30
GPMCA[16:1]
GPMC_AD[15:0]
29
Valid Address (LSB)
Data OUT
GPMC_WAIT[x]
Figure 8-32. GPMC/Multiplexed NOR Flash - Asynchronous Write - Single Word Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
267
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.8.2.3
www.ti.com
GPMC/NAND Flash and ELM Interface Timing
Table 8-38. Timing Requirements for GPMC/NAND Flash Interface
(see Figure 8-35)
OPP100/120/166
NO.
13
(1)
MIN
tacc(DAT)
MAX
J (1)
Data maximum access time (GPMC_FCLK cycles)
UNIT
cycles
J = AccessTime * (TimeParaGranularity + 1)
Table 8-39. Switching Characteristics Over Recommended Operating Conditions for GPMC/NAND Flash
Interface
(see Figure 8-33, Figure 8-34, Figure 8-35, Figure 8-36)
NO.
1
OPP100/120/166
PARAMETER
tw(nWEV)
MIN
MAX
UNIT
A (1)
ns
(2)
B + 4 (2)
ns
Pulse duration, GPMC_WE valid time
2
td(nCSV-nWEV)
Delay time, GPMC_CS[X] valid to GPMC_WE valid
B-2
3
td(CLEH-nWEV)
Delay time, GPMC_BE0_CLE high to GPMC_WE valid
C - 2 (3)
C + 4 (3)
ns
(4)
(4)
ns
4
td(nWEV-DV)
Delay time, GPMC_D[15:0] valid to GPMC_WE valid
D-2
5
td(nWEIV-DIV)
Delay time, GPMC_WE invalid to GPMC_AD[15:0] invalid
E - 2 (5)
D+4
E + 4 (5)
ns
6
td(nWEIV-CLEIV)
Delay time, GPMC_WE invalid to GPMC_BE0_CLE invalid
F - 2 (6)
F + 4 (6)
ns
(7)
(7)
ns
7
td(nWEIV-nCSIV)
Delay time, GPMC_WE invalid to GPMC_CS[X] invalid
G-2
8
td(ALEH-nWEV)
Delay time, GPMC_ADV_ALE High to GPMC_WE valid
C - 2 (3)
C + 4 (3)
ns
9
td(nWEIV-ALEIV)
Delay time, GPMC_WE invalid to GPMC_ADV_ALE invalid
F - 2 (6)
F + 4 (6)
ns
10
tc(nWE)
Cycle time, write cycle time
H (8)
ns
(9)
ns
11
td(nCSV-nOEV)
Delay time, GPMC_CS[X] valid to GPMC_OE_RE valid
12
tw(nOEV)
Pulse duration, GPMC_OE_RE valid time
K (10)
ns
13
tc(nOE)
Cycle time, read cycle time
L (11)
ns
(12)
ns
14
td(nOEIV-nCSIV)
I-2
(9)
G+4
Delay time, GPMC_OE_RE invalid to GPMC_CS[X] invalid
M-2
(12)
I+4
M+4
(1)
(2)
A = (WEOffTime - WEOnTime) * (TimeParaGranularity + 1) * GPMC_FCLK
= B + nWE Min Delay - nCS Max Delay
B = ((WEOnTime - CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (WEExtraDelay - CSExtraDelay)) * GPMC_FCLK
(3) = C + nWE Min Delay - CLE Max Delay
C = ((WEOnTime - ADVOnTime) * (TimeParaGranularity + 1) + 0.5 * (WEExtraDelay - ADVExtraDelay)) * GPMC_FCLK
(4) = D + nWE Min Delay - Data Max Delay
D = (WEOnTime * (TimeParaGranularity + 1) + 0.5 * WEExtraDelay ) * GPMC_FCLK
(5) =E + Data Min Delay - nWE Max Delay
E = ((WrCycleTime - WEOffTime) * (TimeParaGranularity + 1) - 0.5 * WEExtraDelay ) * GPMC_FCLK
(6) = F + CLE Min Delay - nWE Max Delay
F = ((ADVWrOffTime - WEOffTime) * (TimeParaGranularity + 1) + 0.5 * (ADVExtraDelay - WEExtraDelay )) * GPMC_FCLK
(7) =G + nCS Min Delay - nWE Max Delay
G = ((CSWrOffTime - WEOffTime) * (TimeParaGranularity + 1) + 0.5 * (CSExtraDelay - WEExtraDelay )) * GPMC_FCLK
(8) H = WrCycleTime * (1 + TimeParaGranularity) * GPMC_FCLK
(9) = I + nOE Min Delay - nCS Max Delay
I = ((OEOnTime - CSOnTime) * (TimeParaGranularity + 1) + 0.5 * (OEExtraDelay - CSExtraDelay)) * GPMC_FCLK
(10) K = (OEOffTime - OEOnTime) * (1 + TimeParaGranularity) * GPMC_FCLK
(11) L = RdCycleTime * (1 + TimeParaGranularity) * GPMC_FCLK
(12) =M + nCS Min Delay - nOE Max Delay
M = ((CSRdOffTime - OEOffTime) * (TimeParaGranularity + 1) + 0.5 * (CSExtraDelay - OEExtraDelay ))* GPMC_FCLK
268
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
GPMC_FCLK
2
7
GPMC_CS[x]
3
6
GPMC_BE0_CLE
GPMC_ADV_ALE
GPMC_OE
1
GPMC_WE
5
4
GPMC_A[16:1]
GPMC_AD[15:0]
Command
Figure 8-33. GPMC/NAND Flash - Command Latch Cycle Timing
GPMC_FCLK
2
7
GPMC_CS[x]
GPMC_BE0_CLE
8
9
GPMC_ADV_ALE
GPMC_OE
10
1
GPMC_WE
5
4
GPMC_A[16:1]
GPMC_AD[15:0]
Address
Figure 8-34. GPMC/NAND Flash - Address Latch Cycle Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
269
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
GPMC_FCLK
13
16
11
GPMC_CS[x]
GPMC_BE0_CLE
GPMC_ADV_ALE
15
14
GPMC_OE
GPMC_A[16:1]
GPMC_AD[15:0]
Data
GPMC_WAIT[x]
Figure 8-35. GPMC/NAND Flash - Data Read Cycle Timing
GPMC_FCLK
2
7
GPMC_CS[x]
GPMC_BE0_CLE
GPMC_ADV_ALE
GPMC_OE
10
1
GPMC_WE
5
4
GPMC_A[16:1]
GPMC_AD[15:0]
Data
Figure 8-36. GPMC/NAND Flash - Data Write Cycle Timing
270
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
8.9
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
High-Definition Multimedia Interface (HDMI)
The device includes an HDMI 1.3a-compliant transmitter for digital video and audio data to display
devices. The HDMI interface consists of a digital HDMI transmitter core with TMDS encoder, a core
wrapper with interface logic and control registers, and a transmit PHY, with the following features:
• Hot-plug detection
• Consumer electronics control (CEC) messages
• DVI 1.0 compliant (only RGB pixel format)
• CEA 861-D and VESA DMT formats
• Supports up to 165-MHz pixel clock
– 1920 x 1080p @75 Hz with 8-bit/component color depth
– 1600 x 1200 @60 Hz with 8-bit/component color depth
• Support for deep-color mode:
– 10-bit/component color depth up to 1080p @60 Hz (Max pixel clock = 148.5 MHz)
– 12-bit/component color depth up to 720p/1080i @60 Hz (Max pixel clock = 123.75 MHz)
• TMDS clock to the HDMI-PHY is up to 185.625 MHz
• Maximum supported pixel clock:
– 165 MHz for 8-bit color depth
– 148.5 MHz for 10-bit color depth
– 123.75 MHz for 12-bit color depth
• Uncompressed multichannel (up to eight channels) audio (L-PCM) support
• Master I2C interface for display data channel (DDC) connection
For more details on the HDMI, see the High-Definition Multimedia Interface (HDMI) chapter of the
TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
8.9.1
HDMI Design Guidelines
This section provides PCB design and layout guidelines for the HDMI interface. The design rules constrain
PCB trace length, PCB trace skew, signal integrity, cross-talk, and signal timing. Simulation and system
design work has been done to ensure the HDMI interface requirements are met.
8.9.1.1
HDMI Interface Schematic
The HDMI bus is separated into three main sections:
1. Transition Minimized Differential Signaling (TMDS) high-speed digital video interface
2. Display Data Channel (I2C bus for configuration and status exchange between two devices)
3. Consumer Electronics Control (optional) for remote control of connected devices.
The DDC and CEC are low-speed interfaces, so nothing special is required for PCB layout of these
signals. Their connection is shown in Figure 8-37, HDMI Interface High-Level Schematic.
The TMDS channels are high-speed differential pairs and, therefore, require the most care in layout.
Specifications for TMDS layout are below.
Figure 8-37 shows the HDMI interface schematic. The specific pin numbers can be obtained from Table 315, HDMI Terminal Functions.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
271
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Device
HDMI Connector
HDMI_DP0
HDMI_DN0
TD0+
TD0-
HDMI_DP1
HDMI_DN1
TD1+
TD1TPD12S521
or other
ESD Protection
w/I2C-Level
Translation
HDMI_DP2
HDMI_DN2
HDMI_CLKP
HDMI_CLKN
TD0
Shld
TD1
Shld
TD2
Shld
TD2+
TD2TCLK
TCLK+
HDMI_CEC
TCLK
Shld
CEC
DDC
Gnd
3.3 V
Rpullup
HDMI_SDA
HDMI_SCL
HDMI_HPDET
A.
(A)
SDA
SCL
HPDET
5K-10K Ω pullup resistors are required if not integrated in the ESD protection chip.
Figure 8-37. HDMI Interface High-Level Schematic
8.9.1.2
TMDS Routing
The TMDS signals are high-speed differential pairs. Care must be taken in the PCB layout of these signals
to ensure good signal integrity.
The TMDS differential signal traces must be routed to achieve 100 Ω (±10%) differential impedance and
60 Ω (±10%) single-ended impedance. Single-ended impedance control is required because differential
signals are extremely difficult to closely couple on PCBs and, therefore, single-ended impedance becomes
important.
These impedances are impacted by trace width, trace spacing, distance to reference planes, and dielectric
material. Verify with a PCB design tool that the trace geometry for both data signal pairs results in as
close to 60 Ω impedance traces as possible. For best accuracy, work with your PCB fabricator to ensure
this impedance is met.
In general, closely coupled differential signal traces are not an advantage on PCBs. When differential
signals are closely coupled, tight spacing and width control is necessary. Very small width and spacing
variations affect impedance dramatically, so tight impedance control can be more problematic to maintain
in production.
Loosely coupled PCB differential signals make impedance control much easier. Wider traces and spacing
make obstacle avoidance easier, and trace width variations do not affect impedance as much; therefore, it
is easier to maintain an accurate impedance over the length of the signal. The wider traces also show
reduced skin effect and, therefore, often result in better signal integrity.
Table 8-40 shows the routing specifications for the TMDS signals.
Table 8-40. TMDS Routing Specifications
PARAMETER
MIN
TYP
Processor-to-HDMI header trace length
MAX
7000
Number of stubs allowed on TMDS traces
0
UNIT
Mils
Stubs
Ω
TX/RX pair differential impedance
90
100
110
TX/RX single ended impedance
54
60
66
Ω
2
Vias (1)
Number of vias on each TMDS trace
(1)
272
Vias must be used in pairs with their distance minimized.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-40. TMDS Routing Specifications (continued)
PARAMETER
TMDS differential pair to any other trace spacing
(2)
MIN
TYP
MAX
UNIT
2*DS (2)
DS = differential spacing of the HDMI traces.
8.9.1.3
DDC Signals
As shown in Figure 8-37, HDMI Interface High-Level Schematic, the DDC connects just like a standard
I2C bus. As such, resistor pullups must be used to pull up the open drain buffer signals unless they are
integrated into the ESD protection chip used. If used, these pullup resistors should be connected to a 3.3V supply.
8.9.1.4
HDMI ESD Protection Device (Required)
Interfaces that connect to a cable such as HDMI generally require more ESD protection than can be built
into the outputs of the processor. Therefore, this HDMI interface requires the use of an ESD protection
chip to provide adequate ESD protection and to translate I2C voltage levels from the 3.3 V supplied by the
device to the 5 volts required by the HDMI specification.
When selecting an ESD protection chip, choose the lowest capacitance ESD protection available to
minimize signal degradation. In no case should the ESD protection circuit capacitance be more than 5 pF.
TI manufactures devices that provide ESD protection for HDMI signals such as the TPD12S521. For more
information see the www.ti.com website.
8.9.1.5
PCB Stackup Specifications
Table 8-41 shows the stackup and feature sizes required for HDMI.
Table 8-41. HDMI PCB Stackup Specifications
MIN
TYP
MAX
PCB routing/plane layers
PARAMETER
4
6
-
Layers
Signal routing layers
2
3
-
Layers
Number of ground plane cuts allowed within HDMI routing region
-
-
0
Cuts
Number of layers between HDMI routing region and reference ground plane
-
-
0
Layers
PCB trace width
-
4
-
Mils
PCB BGA escape via pad size
-
20
-
Mils
PCB BGA escape via hole size
-
10
Mils
0.4
mm
Processor device BGA pad size
(1)
(2)
(1) (2)
UNIT
Non-solder mask defined pad.
Per IPC-7351A BGA pad size guideline.
8.9.1.6
Grounding
Each TMDS channel has its own shield pin which should be grounded to provide a return current path for
the TMDS signal.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
273
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.10 High-Definition Video Processing Subsystem (HDVPSS)
The device High-Definition Video Processing Subsystem (HDVPSS) provides a video input interface for
external imaging peripherals (that is, image sensors, video decoders, and so on) and a video output
interface for display devices, such as analog SDTV displays, digital HDTV displays, digital LCD panels,
and so on. The HDVPSS includes HD and SD video encoders and an HDMI transmitter interface.
The device HDVPSS features include:
• Two display processing pipelines with de-interlacing, scaling, alpha blending, chroma keying, color
space conversion, flicker filtering, and pixel format conversion.
• HD/SD compositor features for PIP support.
• Format conversions (up to 1080p 60 Hz) include scan format conversion, scan rate conversion, aspectratio conversion, and frame size conversion.
• Supports additional video processing capabilities by using the memory-to-memory feature of the
subsystem.
• Two parallel video processing pipelines support HD (up to 1080p60) and SD (NTSC/PAL)
simultaneous outputs.
– SD analog output with OSD with embedded timing codes (BT.656)
• S-video or Composite output
• 2-channel SD-DAC with 10-bit resolution
• Options available to support MacroVision and CGMS-A (contact local TI Sales rep for
information).
– Digital HDMI 1.3a-compliant transmitter (for details, see Section 8.9, High-Definition Multimedia
Interface (HDMI)).
– One digital video output supporting up to 30-bits @ 165 MHz
– One digital video output supporting up to 24-bits @ 165 MHz
• Two independently configurable external video input capture ports (up to 165 MHz).
– 16/24-bit HD digital video input or dual clock independent 8-bit SD inputs on each capture port.
– 8/16/24-bit digital video input
– 8-bit digital video input
– Embedded sync and external sync modes are supported for all input configurations (VIN1 Port B
supports embedded sync only).
– De-multiplexing of both pixel-to-pixel and line-to-line multiplexed streams, effectively supporting up
to 16 simultaneous SD inputs with a glueless interface to an external multiplexer such as the
TVP5158.
– Additional features include: programmable color space conversion, scaler and chroma
downsampler, ancillary VANC/VBI data capture (decoded by software).
• Graphics features:
– Three independently-generated graphics layers.
– Each supports full-screen resolution graphics in HD, SD or both.
– Up/down scaler optimized for graphics.
– Global and pixel-level alpha blending supported.
For more detailed information on specific features and registers, see the High Definition Video Processing
Subsystem chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference
Manual (Literature Number: SPRUGZ8).
274
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.10.1 HDVPSS Electrical Data/Timing
Table 8-42. Timing Requirements for HDVPSS Input
(see Figure 8-38 and Figure 8-39)
OPP100/120/166
NO.
MIN
MAX
UNIT
VIN[X]A_CLK
6.06 (1)
ns
Pulse duration, VIN[x]A_CLK high (45% of tc)
2.73
ns
Pulse duration, VIN[x]A_CLK low (45% of tc)
2.73
ns
1
tc(CLK)
Cycle time, VIN[x]A_CLK
2
tw(CLKH)
3
tw(CLKH)
tsu(DE-CLK)
tsu(VSYNC-CLK)
4
tsu(FLD-CLK)
Input setup time, control valid to VIN[x]A_CLK high/low
3
Input setup time, data valid to VIN[x]A_CLK high/low
3
ns
tsu(HSYNC-CLK)
tsu(D-CLK)
th(CLK-DE)
th(CLK-VSYNC)
5
th(CLK-FLD)
Input hold time, control valid from VIN[x]A_CLK high/low
0.1
Input hold time, data valid from VIN[x]A_CLK high/low
0.1
ns
th(CLK-HSYNC)
th(CLK-D)
VIN[x]B_CLK
6.06 (1)
ns
Pulse duration, VIN[x]B_CLK high (45% of tc)
2.73
ns
Pulse duration, VIN[x]B_CLK low (45% of tc)
2.73
ns
1
tc(CLK)
Cycle time, VIN[x]B_CLK
2
tw(CLKH)
3
tw(CLKH)
tsu(DE-CLK)
tsu(VSYNC-CLK)
4
tsu(FLD-CLK)
Input setup time, control valid to VIN[x]B_CLK high/low
3
Input setup time, data valid to VIN[x]B_CLK high/low
3
ns
tsu(HSYNC-CLK)
tsu(D-CLK)
th(CLK-DE)
th(CLK-VSYNC)
5
th(CLK-FLD)
Input hold time, control valid from VIN[x]B_CLK high/low
0.1
Input hold time, data valid from VIN[x]B_CLK high/low
0.1
ns
th(CLK-HSYNC)
th(CLK-D)
(1)
For maximum frequency of 165 MHz.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
275
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-43. Switching Characteristics Over Recommended Operating Conditions for HDVPSS Output
(see Figure 8-38 and Figure 8-40)
NO.
OPP100/120/166
PARAMETER
MIN
MAX
UNIT
6.06 (1)
ns
Pulse duration, VOUT[x]_CLK high (45% of tc)
2.73
ns
tw(CLKL)
Pulse duration, VOUT[x]_CLK low (45% of tc)
2.73
tt(CLK)
Transition time, VOUT[x]_CLK (10%-90%)
1
tc(CLK)
Cycle time, VOUT[x]_CLK
2
tw(CLKH)
3
7
ns
2.64
ns
-1.2
2
ns
-1.2
2
ns
td(CLK-AVID)
td(CLK-FLD)
Delay time, VOUT[x]_CLK low (falling) to control valid
td(CLK-VSYNC)
td(CLK-HSYNC)
6
td(CLK-RCR)
td(CLK-GYYC)
Delay time, VOUT[0]_CLK low (falling) to data valid
td(CLK-BCBC)
td(CLK-YYC)
Delay time, VOUT[1]_CLK low (falling) to data valid
td(CLK-C)
(1)
For maximum frequency of 165 MHz.
3
2
1
VIN[x]A_CLK/
VIN[x]B_CLK/
VOUT[x]_CLK
7
1
7
Figure 8-38. HDVPSS Clock Timing
276
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
VIN[x]A_CLK/
VIN[x]B_CLK
(positive-edge clocking)
VIN[x]A_CLK/
VIN[x]B_CLK
(negative-edge clocking)
5
4
VIN[x]A/
VIN[x]B
Figure 8-39. HDVPSS Input Timing
VOUT[x]_CLK
6
VOUT[x]
Figure 8-40. HDVPSS Output Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
277
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.10.2 Video DAC Guidelines and Electrical Data/Timing
The analog video DAC outputs of the device can be operated in one of two modes: Normal mode and
TVOUT Bypass mode. In Normal mode, the device’s internal video amplifier is used. In TVOUT Bypass
mode, the internal video amplifier is bypassed and an external amplifier is required.
Figure 8-41 shows a typical circuit that permits connecting the analog video output from the device to
standard 75-Ω impedance video systems in Normal mode. Figure 8-42 shows a typical circuit that permits
connecting the analog video output from the device to standard 75-Ω impedance video systems in TVOUT
Bypass mode.
Reconstruction
(A)
Filter
~9.5 MHz
TV_OUTx
CAC
(B)
ROUT
TV_VFBx
A.
B.
Reconstruction Filter (optional)
AC coupling capacitor (optional)
Figure 8-41. TV Output (Normal Mode)
Reconstruction
(A)
Filter
~9.5 MHz
TV_VFBx
Amplifier
3.7 V/V
75 Ω
CAC
(B)
RLOAD
A.
B.
Reconstruction Filter (optional). Note: An amplifier with an integrated reconstruction filter can alternatively be used
instead of a discrete reconstruction filter.
AC coupling capacitor (optional)
Figure 8-42. TV Output (TVOUT Bypass Mode)
During board design, the onboard traces and parasitics must be matched for the channel. The video DAC
output pins (TV_OUTx/TV_VFBx) are very high-frequency analog signals and must be routed with
extreme care. As a result, the paths of these signals must be as short as possible, and as isolated as
possible from other interfering signals. In TVOUT Bypass mode, the load resistor and amplifier/buffer
should be placed as close as possible to the TV_VFBx pins. Other layout guidelines include:
• Take special care to bypass the VDDA_VDAC_1P8 power supply pin with a capacitor. For more
information, see Section 7.2.9, Power-Supply Decoupling.
• In TVOUT Bypass mode, place the RLOAD resistor as close as possible to the Reconstruction Filter
and Amplifier. In addition, place the 75-Ω resistor as close as possible (< 0.5 ") to the Amplifier/buffer
output pin. To maintain a high-quality video signal, the onboard traces after the 75-Ω resistor should
have a characteristic impedance of 75 Ω (± 20%).
• In Normal mode, TV_VFBx is the most sensitive pin in the TV out system. The ROUT resistor should
be placed as close as possible to the device pins. To maintain a high-quality video signal, the onboard
traces leading to the TV_OUTx pin should have a characteristic impedance of 75 Ω (± 20%) starting
from the closest possible place to the device pin output.
• Minimize input trace lengths to the device to reduce parasitic capacitance.
• Include solid ground return paths.
• Match trace lengths as close as possible within a video format group (that is, Y and C for S-Video
output should match each other).
278
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
For additional Video DAC Design guidelines, see the High Definition Video Processing Subsystem chapter
of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature
Number: SPRUGZ8).
Table 8-44. Static and Dynamic DAC Specifications
VDAC STATIC SPECIFICATIONS
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Reference Current Setting Resistor
(RSET)
Normal Mode
4653
4700
4747
Ω
TVOUT Bypass Mode
9900
10000
10100
Ω
Output resistor between TV_OUTx
and TV_VFBx pins (ROUT)
Normal Mode
2673
2700
2727
Ω
Load Resistor (RLOAD)
Normal Mode
TVOUT Bypass Mode
N/A
75-Ω Inside the Display
TVOUT Bypass Mode
1485
AC-Coupling Capacitor (Optional)
[CAC]
Normal Mode
220
Total Capacitance from TV_OUTx
to VSSA_VDAC_1P8
Normal Mode
TVOUT Bypass Mode
1500
1515
See External Amplifier Specification
TVOUT Bypass Mode
300
pF
4
LSB
N/A
Resolution
10
Integral Non-Linearity (INL), Best
Fit
Normal Mode
Differential Non-Linearity (DNL)
Normal Mode
TVOUT Bypass Mode
Full-Scale Output Voltage
Full-Scale Output Current
-1
1
LSB
-2.5
2.5
LSB
-1
1
LSB
Normal Mode (RLOAD = 75 Ω)
1.3
V
TVOUT Bypass Mode (RLOAD =
1.5 kΩ)
0.7
V
470
uA
Normal Mode
N/A
TVOUT Bypass Mode
Gain Error
Gain Mismatch (Luma-to-Chroma)
Normal Mode (Composite) and
TVOUT Bypass Mode
-10
Normal Mode (S-Video)
-20
Normal Mode (Composite)
Normal Mode (S-Video)
Output Impedance
Bits
-4
TVOUT Bypass Mode
Ω
uF
10
%FS
20
%FS
10
%
N/A
-10
Looking into TV_OUTx nodes
Ω
75
VDAC DYNAMIC SPECIFICATIONS
PARAMETER
TEST CONDITIONS
Output Update Rate (FCLK)
MIN
TYP
MAX
UNIT
54
60
MHz
Signal Bandwidth
3 dB
6
MHz
Spurious-Free Dynamic Range
(SFDR) within bandwidth
FCLK = 54 MHz, FOUT = 1 MHz
50
dBc
Signal-to-Noise Ration (SNR)
FCLK = 54 MHz, FOUT = 1 MHz
54
dB
Normal Mode, 100 mVpp @ 6
MHz on VDDA_VDAC_1P8
6
TVOUT Bypass Mode, 100
mVpp @ 6 MHz on
VDDA_VDAC_1P8
20
Power Supply Rejection (PSR)
dB
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
279
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.11 Inter-Integrated Circuit (I2C)
The device includes four inter-integrated circuit (I2C) modules which provide an interface to other devices
compliant with Philips Semiconductors Inter-IC bus (I2C-bus™) specification version 2.1. External
components attached to this 2-wire serial bus can transmit/receive 8-bit data to/from the device through
the I2C module. The I2C port does not support CBUS compatible devices.
The I2C port supports the following features:
• Compatible with Philips I2C Specification Revision 2.1 (January 2000)
• Standard and fast modes from 10 - 400 Kbps (no fail-safe I/O buffers)
• Noise filter to remove noise 50 ns or less
• Seven- and ten-bit device addressing modes
• Multimaster transmitter/slave receiver mode
• Multimaster receiver/slave transmitter mode
• Combined master transmit/receive and receive/transmit modes
• Two DMA channels, one interrupt line
• Built-in FIFO (32 byte) for buffered read or write.
For more detailed information on the I2C peripheral, see the Inter-Integrated Circuit (I2C) Controller
Module chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual
(Literature Number: SPRUGZ8).
8.11.1 I2C Peripheral Register Descriptions
Table 8-45. I2C Registers
HEX ADDRESS
I2C0
I2C1
I2C2
I2C3
ACRONYM
REGISTER NAME
0x4802 8000
0x4802 A000
0x4819 C000
0x4819 E000
I2C_REVNB_LO
Module Revision (LOW BYTES)
0x4802 8004
0x4802 A004
0x4819 C004
0x4819 E004
I2C_REVNB_HI
Module Revision (HIGH BYTES)
0x4802 8010
0x4802 A010
0x4819 C010
0x4819 E010
I2C_SYSC
System configuration
0x4802 8020
0x4802 A020
0x4819 C020
0x4819 E020
I2C_EOI
I2C End of Interrupt
0x4802 8024
0x4802 A024
0x4819 C024
0x4819 E024
I2C_IRQSTATUS_RA
W
0x4802 8028
0x4802 A028
0x4819 C028
0x4819 E028
I2C_IRQSTATUS
0x4802 802C
0x4802 A02C
0x4819 C02C
0x4819 E02C
I2C_IRQENABLE_SET I2C Interrupt Enable Set
0x4802 8030
0x4802 A030
0x4819 C030
0x4819 E030
I2C_IRQENABLE_CLR I2C Interrupt Enable Clear
0x4802 8034
0x4802 A034
0x4819 C034
0x4819 E034
I2C_WE
0x4802 8038
0x4802 A038
0x4819 C038
0x4819 E038
I2C_DMARXENABLE_
SET
Receive DMA Enable Set
0x4802 803C
0x4802 A03C
0x4819 C03C
0x4819 E03C
I2C_DMATXENABLE_
SET
Transmit DMA Enable Set
0x4802 8040
0x4802 A040
0x4819 C040
0x4819 E040
I2C_DMARXENABLE_
CLR
Receive DMA Enable Clear
0x4802 8044
0x4802 A044
0x4819 C044
0x4819 E044
I2C_DMATXENABLE_
CLR
Transmit DMA Enable Clear
I2C Status Raw
I2C Status
I2C Wakeup Enable
0x4802 8048
0x4802 A048
0x4819 C048
0x4819 E048
I2C_DMARXWAKE_EN Receive DMA Wakeup
0x4802 804C
0x4802 A04C
0x4819 C04C
0x4819 E04C
I2C_DMATXWAKE_EN Transmit DMA Wakeup
0x4802 8090
0x4802 A090
0x4819 C090
0x4819 E090
0x4802 8094
0x4802 A094
0x4819 C094
0x4819 E094
I2C_BUF
Buffer Configuration
0x4802 8098
0x4802 A098
0x4819 C098
0x4819 E098
I2C_CNT
Data Counter
0x4802 809C
0x4802 A09C
0x4819 C09C
0x4819 E09C
I2C_DATA
Data Access
0x4802 80A4
0x4802 A0A4
0x4819 C0A4
0x4819 E0A4
I2C_CON
I2C Configuration
0x4802 80A8
0x4802 A0A8
0x4819 C0A8
0x4819 E0A8
I2C_OA
I2C Own Address
280
Peripheral Information and Timings
I2C_SYSS
System Status
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-45. I2C Registers (continued)
HEX ADDRESS
I2C0
I2C1
I2C2
I2C3
ACRONYM
REGISTER NAME
0x4802 80AC
0x4802 A0AC
0x4819 C0AC
0x4802 80B0
0x4802 A0B0
0x4819 C0B0
0x4819 E0AC
I2C_SA
I2C Slave Address
0x4819 E0B0
I2C_PSC
0x4802 80B4
0x4802 A0B4
0x4819 C0B4
I2C Clock Prescaler
0x4819 E0B4
I2C_SCLL
I2C SCL Low Time
I2C SCL High Time
0x4802 80B8
0x4802 A0B8
0x4819 C0B8
0x4819 E0B8
I2C_SCLH
0x4802 80BC
0x4802 A0BC
0x4819 C0BC
0x4819 E0BC
I2C_SYSTEST
System Test
0x4802 80C0
0x4802 A0C0
0x4819 C0C0
0x4819 E0C0
I2C_BUFSTAT
I2C Buffer Status
0x4802 80C4
0x4802 A0C4
0x4819 C0C4
0x4819 E0C4
I2C_OA1
I2C Own Address 1
0x4802 80C8
0x4802 A0C8
0x4819 C0C8
0x4819 E0C8
I2C_OA2
I2C Own Address 2
0x4802 80CC
0x4802 A0CC
0x4819 C0CC
0x4819 E0CC
I2C_OA3
I2C Own Address 3
0x4802 80D0
0x4802 A0D0
0x4819 C0D0
0x4819 E0D0
I2C_ACTOA
Active Own Address
0x4802 80D4
0x4802 A0D4
0x4819 C0D4
0x4819 E0D4
I2C_SBLOCK
I2C Clock Blocking Enable
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
281
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.11.2 I2C Electrical Data/Timing
Table 8-46. Timing Requirements for I2C Input Timings (1)
(see Figure 8-43)
OPP100/120/166
STANDARD
MODE
NO.
MIN
1
MAX
FAST MODE
MIN
UNIT
MAX
tc(SCL)
Cycle time, SCL
10
2.5
µs
2
tsu(SCLH-SDAL)
Setup time, SCL high before SDA low (for a repeated START
condition)
4.7
0.6
µs
3
th(SDAL-SCLL)
Hold time, SCL low after SDA low (for a START and a
repeated START condition)
4
0.6
µs
4
tw(SCLL)
Pulse duration, SCL low
4.7
1.3
µs
5
tw(SCLH)
Pulse duration, SCL high
4
0.6
µs
(2)
6
tsu(SDAV-SCLH)
Setup time, SDA valid before SCL high
250
7
th(SCLL-SDAV)
Hold time, SDA valid after SCL low
0 (3) 3.45 (4)
100
0 (3)
8
tw(SDAH)
Pulse duration, SDA high between STOP and START
conditions
4.7
1.3
9
tr(SDA)
Rise time, SDA
1000
20 + 0.1Cb
(5)
300
ns
10
tr(SCL)
Rise time, SCL
1000
20 + 0.1Cb
(5)
300
ns
300
ns
300
ns
11
tf(SDA)
Fall time, SDA
300
20 + 0.1Cb
(5)
12
tf(SCL)
Fall time, SCL
300
20 + 0.1Cb
(5)
13
tsu(SCLH-SDAH)
Setup time, SCL high before SDA high (for STOP condition)
14
tw(SP)
Pulse duration, spike (must be suppressed)
15
(5)
(1)
(2)
(3)
(4)
(5)
Cb
4
ns
0.9 (4)
µs
0.6
µs
0
Capacitive load for each bus line
400
µs
50
ns
400
pF
The I2C pins SDA and SCL do not feature fail-safe I/O buffers. These pins could potentially draw current when the device is powered
down.
A Fast-mode I2C-bus™ device can be used in a Standard-mode I2C-bus system, but the requirement tsu(SDA-SCLH)≥ 250 ns must then be
met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch
the LOW period of the SCL signal, it must output the next data bit to the SDA line tr max + tsu(SDA-SCLH)= 1000 + 250 = 1250 ns
(according to the Standard-mode I2C-Bus Specification) before the SCL line is released.
A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge the
undefined region of the falling edge of SCL.
The maximum th(SDA-SCLL) has only to be met if the device does not stretch the low period [tw(SCLL)] of the SCL signal.
Cb = total capacitance of one bus line in pF. If mixed with HS-mode devices, faster fall-times are allowed.
9
11
I2C[x]_SDA
6
8
14
4
13
5
10
I2C[x]_SCL
1
12
3
7
2
3
Stop
Start
Repeated
Start
Stop
Figure 8-43. I2C Receive Timing
282
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-47. Switching Characteristics Over Recommended Operating Conditions for I2C Output Timings
(see Figure 8-44)
OPP100/120/166
NO.
STANDARD
MODE
PARAMETER
MIN
16
(1)
MAX
FAST MODE
MIN
UNIT
MAX
tc(SCL)
Cycle time, SCL
10
2.5
µs
17
tsu(SCLH-SDAL)
Setup time, SCL high before SDA low (for a repeated START
condition)
4.7
0.6
µs
18
th(SDAL-SCLL)
Hold time, SCL low after SDA low (for a START and a repeated
START condition)
4
0.6
µs
19
tw(SCLL)
Pulse duration, SCL low
4.7
1.3
µs
20
tw(SCLH)
Pulse duration, SCL high
4
0.6
µs
21
tsu(SDAV-SCLH)
Setup time, SDA valid before SCL high
250
100
22
th(SCLL-SDAV)
Hold time, SDA valid after SCL low (for I2C bus devices)
23
tw(SDAH)
Pulse duration, SDA high between STOP and START
conditions
24
tr(SDA)
Rise time, SDA
1000
20 + 0.1Cb
300
ns
25
tr(SCL)
Rise time, SCL
1000
20 + 0.1Cb
300
ns
26
tf(SDA)
Fall time, SDA
300
20 + 0.1Cb
300
ns
27
tf(SCL)
Fall time, SCL
300
20 + 0.1Cb
300
ns
28
tsu(SCLH-SDAH)
Setup time, SCL high before SDA high (for STOP condition)
29
Cp
Capacitance for each I2C pin
0
3.45
4.7
0
ns
0.9
µs
1.3
4
(1)
(1)
(1)
(1)
µs
0.6
10
µs
10
pF
Cb = total capacitance of one bus line in pF. If mixed with HS-mode devices, faster fall-times are allowed.
24
26
I2C[x]_SDA
21
23
19
28
20
25
I2C[x]_SCL
27
16
18
22
17
18
Stop
Start
Repeated
Start
Stop
Figure 8-44. I2C Transmit Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
283
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.12 Imaging Subsystem (ISS)
The device Imaging Subsystem captures and processes pixel data from external image and video inputs.
The inputs can be connected to the Image Processing block through the Parallel Camera Interface
(CAM). . In addition, a Timing control module provides flash strobe and mechanical shutter interfaces. The
features of each component of the ISS are described below.
• Parallel Camera (CAM) interface features:
– Input format
• Bayer pattern Raw (up to 16bit) or YCbCr 422 (8bit or 16bit) data.
• ITU-R BT.656/1120 standard format
– Generates HD/VD timing signals and field ID to an external timing generator, or can synchronize to
the external timing generator.
– Support for progressive and interlaced sensors (hardware support for up to 2 fields and firmware
supports for higher number of fields, typically 3-, 4-, and 5-field sensors.
• Image Sensor Interface (ISIF) features:
– Support for up to 32K pixels (image size) in both the horizontal and vertical direction
– Color space conversion for non-Bayer pattern Raw data
– Digital black clamping with Horizontal/Vertical offset drift compensation
– Vertical Line defect correction based on a lookup table
– Color-dependent gain control and black level offset control
– Ability to control output to the DDR2/DDR3 via an external write enable signal
– Down sampling via programmable culling patterns
– A-law/DPCM compression
– Generating 16-, 12- or 8-bit output to memory
• Two independent Resizers
– Providing two different sizes of outputs simultaneously on one input
– Maximum line width is 5376 and 2336, respectively
– YUV422 to YUV420 conversion
– Data output format: RGB565, ARGB888, YUV422 co sited and YUV4:2:0 planar
– Resizer Ratio: x1/4096 approximately x20
– Input from memory
• Timing control module features:
– STROBE signal for flash pre-strobe and flash strobe
– SHUTTER signal for mechanical shutter control
– Global reset control
For more detailed information on the ISS, see the ISS Overview section, the ISS Interfaces section, and
the ISS ISP section of the Watchdog Timer chapter of the TMS320DM814x DaVinci Digital Media
Processors Technical Reference Manual (Literature Number: SPRUGZ8).
284
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.12.1 ISSCAM Electrical Data/Timing
Table 8-48. Timing Requirements for ISSCAM (see Figure 8-45)
OPP100/120/166
NO.
MIN
NOM
MAX
UNIT
1
tc(PCLK)
Cycle time, PCLK
6.06
ns
2
tw(PCLKH)
Pulse duration, PCLK high
2.73
ns
3
tw(PCLKL)
Pulse duration, PCLK low
2.73
ns
4
tt(PCLK)
Transition time, PCLK
5
ns
3.11
ns
tsu(DE-PCLK)
3.11
ns
tsu(VS-PCLK)
3.11
ns
tsu(HS-PCLK)
Input setup time, Data/Control valid before PCLK high/low
3.11
ns
tsu(FLD-PCLK)
3.11
ns
th(PCLK-DATA)
-0.15
ns
-0.15
ns
-0.15
ns
th(PCLK-HS)
-0.15
ns
th(PCLK-FLD)
-0.15
ns
th(PCLK-DE)
6
2.64
tsu(DATA-PCLK)
th(PCLK-VS)
Input hold time, Data/Control valid after PCLK high/low
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
285
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-49. Switching Characteristics Over Recommended Operating Conditions for ISSCAM (see
Figure 8-45)
NO.
OPP100/120/166
PARAMETER
MIN
MAX
UNIT
15
td(PCLK-FLD)
Delay time, PCLK rising/falling clock edge to Control valid
3
11.5
ns
16
td(PCLK-VS)
Delay time, PCLK rising/falling clock edge to Control valid
3
11.5
ns
17
td(PCLK-HS)
Delay time, PCLK rising/falling clock edge to Control valid
3
11.5
ns
18
td(PCLK-STROBE)
Delay time, PCLK rising/falling clock edge to Control valid
3
11.5
ns
19
td(PCLK-SHUTTER)
Delay time, PCLK rising/falling clock edge to Control valid
3
11.5
ns
PCLK
(negative edge clocking)
4
1
3
PCLK
(positive edge clocking)
2
4
Data/Control input
5
6
Data/Control output
7
Figure 8-45. ISSCAM Timings
286
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.13 DDR2/DDR3 Memory Controller
The device has a dedicated interface to DDR3 and DDR2 SDRAM. The device dedicated interface also
supports JEDEC standard compliant DDR2 and DDR3 SDRAM devices with the following features:
• 16-bit or 32-bit data path to external SDRAM memory
• Memory device capacity: 64Mb, 128Mb, 256Mb, 512Mb, 1Gb, 2Gb, and 4Gb devices
• Support for two independent chip selects, with their corresponding register sets, and independent page
tracking
• Two interfaces with associated DDR2/DDR3 PHYs
• Dynamic memory manager allows for interleaving of data between the two DDR interfaces.
For details on the DDR2/DDR3 Memory Controller, see the DDR2/DDR3 Memory Controller chapter of the
TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
287
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.13.1 DDR2/3 Memory Controller Register Descriptions
Table 8-50. DDR2/3 Memory Controller Registers
DDR0 HEX ADDRESS
DDR1 HEX ADDRESS
ACRONYM
REGISTER NAME
0x4C00 0004
0x4D00 0004
SDRSTAT
SDRAM Status Register
0x4C00 0008
0x4D00 0008
SDRCR
SDRAM Configuration Register
0x4C00 000C
0x4D00 000C
SDRCR2
SDRAM Configuration Register 2
0x4C00 0010
0x4D00 0010
SDRRCR
SDRAM Refresh Control Register
0x4C00 0014
0x4D00 0014
SDRRCSR
SDRAM Refresh Control Shadow Register
0x4C00 0018
0x4D00 0018
SDRTIM1
SDRAM Timing 1 Register
0x4C00 001C
0x4D00 001C
SDRTIM1SR
0x4C00 0020
0x4D00 0020
SDRTIM2
0x4C00 0024
0x4D00 0024
SDRTIM2SR
0x4C00 0028
0x4D00 0028
SDRTIM3
0x4C00 002C
0x4D00 002C
SDRTIM3SR
0x4C00 0038
0x4D00 0038
PMCR
0x4C00 003C
0x4D00 003C
PMCSR
Power Management Control Shadow Register
0x4C00 0054
0x4D00 0054
PBBPR
Peripheral Bus Burst Priority Register
0x4C00 00A0
0x4D00 00A0
EOI
0x4C00 00A4
0x4D00 00A4
SOIRSR
0x4C00 00AC
0x4D00 00AC
SOISR
SDRAM Timing 1 Shadow Register
SDRAM Timing 2 Register
SDRAM Timing 2 Shadow Register
SDRAM Timing 3 Register
SDRAM Timing 3 Shadow Register
Power Management Control Register
End of Interrupt Register
System OCP Interrupt Raw Status Register
System OCP Interrupt Status Register
0x4C00 00B4
0x4D00 00B4
SOIESR
System OCP Interrupt Enable Set Register
0x4C00 00BC
0x4D00 00BC
SOIECR
System OCP Interrupt Enable Clear Register
0x4C00 00C8
0x4D00 00C8
ZQCR
0x4C00 00D4
0x4D00 00D4
0x4C00 00D8
0x4D00 00D8
0x4C00 00DC
0x4D00 00DC
0x4C00 00E4
0x4D00 00E4
DDRPHYCR
0x4C00 00E8
0x4D00 00E8
DDRPHYCSR
0x4C00 0100
0x4D00 0100
PRI_COS_MAP
0x4C00 0104
0x4D00 0104
CONNID_COS_1_MAP
Connection ID to Class of Service 1 Mapping Register
0x4C00 0108
0x4D00 0108
CONNID_COS_2_MAP
Connection ID to Class of Service 2 Mapping Register
0x4C00 0120
0x4D00 0120
RD_WR_EXEC_THRSH
Read Write Execution Threshold Register
RDWR_LVL_RMP_WIN
SDRAM Output Impedance Calibration Configuration
Register
Read-Write Leveling Ramp Window Register
RDWR_LVL_RMP_CTRL Read-Write Leveling Ramp Control Register
RWLCR
Read-Write Leveling Control Register
DDR PHY Control Register
DDR PHY Control Shadow Register
Priority to Class of Service Mapping Register
8.13.2 DDR2/DDR3 PHY Register Descriptions
Table 8-51. DDR2/DDR3 PHY Registers
DDR0 HEX
ADDRESS
DDR1 HEX
ADDRESS
ACRONYM
REGISTER NAME
0x47C0_C41C
0x47C0_C81C
CMD0_REG_PHY_CTRL_SLAVE_RATIO_0
DDR PHY Command 0
Address/Command Slave Ratio Register
0x47C0_C428
0x47C0_C828
CMD0_REG_PHY_DLL_LOCK_DIFF_0
DDR PHY Command 0
Address/Command DLL Lock Difference
Register
0x47C0_C42C
0x47C0_C82C
CMD0_REG_PHY_INVERT_CLKOUT_0
DDR PHY Command 0 Invert Clockout
Selection Register
0x47C0_C450
0x47C0_C850
CMD1_REG_PHY_CTRL_SLAVE_RATIO_0
DDR PHY Command 1
Address/Command Slave Ratio Register
0x47C0_C45C
0x47C0_C85C
CMD1_REG_PHY_DLL_LOCK_DIFF_0
DDR PHY Command 1
Address/Command DLL Lock Difference
Register
288
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-51. DDR2/DDR3 PHY Registers (continued)
DDR0 HEX
ADDRESS
DDR1 HEX
ADDRESS
ACRONYM
0x47C0_C460
0x47C0_C860
CMD1_REG_PHY_INVERT_CLKOUT_0
0x47C0_C484
0x47C0_C884
CMD2_REG_PHY_CTRL_SLAVE_RATIO_0
DDR PHY Command 2
Address/Command Slave Ratio Register
0x47C0_C490
0x47C0_C890
CMD2_REG_PHY_DLL_LOCK_DIFF_0
DDR PHY Command 2
Address/Command DLL Lock Difference
Register
0x47C0_C494
0x47C0_C894
CMD2_REG_PHY_INVERT_CLKOUT_0
DDR PHY Command 2 Invert Clockout
Selection Register
0x47C0_C4C8
0x47C0_C8C8
DATA0_REG_PHY_RD_DQS_SLAVE_RATIO _0
DDR PHY Data Macro 0 Read DQS
Slave Ratio Register
0x47C0_C4DC
0x47C0_C8DC
DATA0_REG_PHY_WR_DQS_SLAVE_RATI O_0
DDR PHY Data Macro 0 Write DQS
Slave Ratio Register
0x47C0_C4F0
0x47C0_C8F0
DATA0_REG_PHY_WRLVL_INIT_RATIO_0
DDR PHY Data Macro 0 Write Leveling
Init Ratio Register
0x47C0_C4F8
0x47C0_C8F8
DATA0_REG_PHY_WRLVL_INIT_MODE_0
DDR PHY Data Macro 0 Write Leveling
Init Mode Ratio Selection Register
0x47C0_C4FC
0x47C0_C8FC
DATA0_REG_PHY_GATELVL_INIT_RATIO_0
DDR PHY Data Macro 0 DQS Gate
Training Init Ratio Register
0x47C0_C504
0x47C0_C904
DATA0_REG_PHY_GATELVL_INIT_MODE_0
DDR PHY Data Macro 0 DQS Gate
Training Init Mode Ratio Selection
Register
0x47C0_C508
0x47C0_C908
DATA0_REG_PHY_FIFO_WE_SLAVE_RATI O_0
DDR PHY Data Macro 0 DQS Gate
Slave Ratio Register
0x47C0_C51C
0x47C0_C91C
DATA0_REG_PHY_DQ_OFFSET_0
0x47C0_C520
0x47C0_C920
DATA0_REG_PHY_WR_DATA_SLAVE_RATI O_0
0x47C0_C534
0x47C0_C934
DATA0_REG_PHY_USE_RANK0_DELAYS
0x47C0_C538
0x47C0_C938
DATA0_REG_PHY_DLL_LOCK_DIFF_0
0x47C0_C56C
0x47C0_C96C
DATA1_REG_PHY_RD_DQS_SLAVE_RATIO _0
DDR PHY Data Macro 1 Read DQS
Slave Ratio Register
0x47C0_C580
0x47C0_C980
DATA1_REG_PHY_WR_DQS_SLAVE_RATI O_0
DDR PHY Data Macro 1 Write DQS
Slave Ratio Register
0x47C0_C594
0x47C0_C994
DATA1_REG_PHY_WRLVL_INIT_RATIO_0
DDR PHY Data Macro 1 Write Leveling
Init Ratio Register
0x47C0_C59C
0x47C0_C99C
DATA1_REG_PHY_WRLVL_INIT_MODE_0
DDR PHY Data Macro 1 Write Leveling
Init Mode Ratio Selection Register
0x47C0_C5A0
0x47C0_C9A0
DATA1_REG_PHY_GATELVL_INIT_RATIO_0
DDR PHY Data Macro 1 DQS Gate
Training Init Ratio Register
0x47C0_C5A8
0x47C0_C9A8
DATA1_REG_PHY_GATELVL_INIT_MODE_0
DDR PHY Data Macro 1 DQS Gate
Training Init Mode Ratio Selection
Register
0x47C0_C5AC
0x47C0_C9AC
DATA1_REG_PHY_FIFO_WE_SLAVE_RATI O_0
DDR PHY Data Macro 1 DQS Gate
Slave Ratio Register
0x47C0_C5C0
0x47C0_C9C0
DATA1_REG_PHY_DQ_OFFSET_1
0x47C0_C5C4
0x47C0_C9C4
DATA1_REG_PHY_WR_DATA_SLAVE_RATI O_0
0x47C0_C5D8
0x47C0_C9D8
DATA1_REG_PHY_USE_RANK0_DELAYS
0x47C0_C5DC
0x47C0_C9DC
DATA1_REG_PHY_DLL_LOCK_DIFF_0
REGISTER NAME
DDR PHY Command 1 Invert Clockout
Selection Register
Offset Value From DQS to DQ for Data
Macro 0
DDR PHY Data Macro 0 Write Data
Slave Ratio Register
DDR PHY Data Macro 0 Delay Selection
Register
DDR PHY Data Macro 0 DLL Lock
Difference Register
Offset Value From DQS to DQ for Data
Macro 1
DDR PHY Data Macro 1 Write Data
Slave Ratio Register
DDR PHY Data Macro 1 Delay Selection
Register
DDR PHY Data Macro 1 DLL Lock
Difference Register
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
289
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-51. DDR2/DDR3 PHY Registers (continued)
DDR0 HEX
ADDRESS
DDR1 HEX
ADDRESS
ACRONYM
0x47C0_C610
0x47C0_CA10
DATA2_REG_PHY_RD_DQS_SLAVE_RATIO _0
DDR PHY Data Macro 2 Read DQS
Slave Ratio Register
0x47C0_C624
0x47C0_CA24
DATA2_REG_PHY_WR_DQS_SLAVE_RATI O_0
DDR PHY Data Macro 2 Write DQS
Slave Ratio Register
0x47C0_C638
0x47C0_CA38
DATA2_REG_PHY_WRLVL_INIT_RATIO_0
DDR PHY Data Macro 2 Write Leveling
Init Ratio Register
0x47C0_C640
0x47C0_CA40
DATA2_REG_PHY_WRLVL_INIT_MODE_0
DDR PHY Data Macro 2 Write Leveling
Init Mode Ratio Selection Register
0x47C0_C644
0x47C0_CA44
DATA2_REG_PHY_GATELVL_INIT_RATIO_0
DDR PHY Data Macro 2 DQS Gate
Training Init Ratio Register
0x47C0_C64C
0x47C0_CA4C
DATA2_REG_PHY_GATELVL_INIT_MODE_0
DDR PHY Data Macro 2 DQS Gate
Training Init Mode Ratio Selection
Register
0x47C0_C650
0x47C0_CA50
DATA2_REG_PHY_FIFO_WE_SLAVE_RATI O_0
DDR PHY Data Macro 2 DQS Gate
Slave Ratio Register
0x47C0_C664
0x47C0_CA64
DATA2_REG_PHY_DQ_OFFSET_2
0x47C0_C668
0x47C0_CA68
DATA2_REG_PHY_WR_DATA_SLAVE_RATI O_0
0x47C0_C67C
0x47C0_CA7C
DATA2_REG_PHY_USE_RANK0_DELAYS
0x47C0_C680
0x47C0_CA80
DATA2_REG_PHY_DLL_LOCK_DIFF_0
0x47C0_C6B4
0x47C0_CAB4
DATA3_REG_PHY_RD_DQS_SLAVE_RATIO _0
DDR PHY Data Macro 3 Read DQS
Slave Ratio Register
0x47C0_C6C8
0x47C0_CAC8
DATA3_REG_PHY_WR_DQS_SLAVE_RATI O_0
DDR PHY Data Macro 3 Write DQS
Slave Ratio Register
0x47C0_C6DC
0x47C0_CADC
DATA3_REG_PHY_WRLVL_INIT_RATIO_0
DDR PHY Data Macro 3 Write Leveling
Init Ratio Register
0x47C0_C6E4
0x47C0_CAE4
DATA3_REG_PHY_WRLVL_INIT_MODE_0
DDR PHY Data Macro 3 Write Leveling
Init Mode Ratio Selection Register
0x47C0_C6E8
0x47C0_CAE8
DATA3_REG_PHY_GATELVL_INIT_RATIO_0
DDR PHY Data Macro 3 DQS Gate
Training Init Ratio Register
0x47C0_C6F0
0x47C0_CAF0
DATA3_REG_PHY_GATELVL_INIT_MODE_0
DDR PHY Data Macro 3 DQS Gate
Training Init Mode Ratio Selection
Register
0x47C0_C6F4
0x47C0_CAF4
DATA3_REG_PHY_FIFO_WE_SLAVE_RATI O_0
DDR PHY Data Macro 3 DQS Gate
Slave Ratio Register
0x47C0_C708
0x47C0_CB08
DATA3_REG_PHY_DQ_OFFSET_3
0x47C0_C70C
0x47C0_CB0C
DATA3_REG_PHY_WR_DATA_SLAVE_RATI O_0
0x47C0_C720
0x47C0_CB20
DATA3_REG_PHY_USE_RANK0_DELAYS
0x47C0_C724
0x47C0_CB24
DATA3_REG_PHY_DLL_LOCK_DIFF_0
REGISTER NAME
Offset value from DQS to DQ for Data
Macro 2
DDR PHY Data Macro 2 Write Data
Slave Ratio Register
DDR PHY Data Macro 2 Delay Selection
Register
DDR PHY Data Macro 2 DLL Lock
Difference Register
Offset Value From DQS to DQ for Data
Macro 3
DDR PHY Data Macro 3 Write Data
Slave Ratio Register
DDR PHY Data Macro 3 Delay Selection
Register
DDR PHY Data Macro 3 DLL Lock
Difference Register
8.13.3 DDR-Related Control Module Registers Description
Table 8-52. DDR-Related Control Module Registers
HEX ADDRESS RANGE
ACRONYM
0x4814 0694
EMIF_CLK_GATE
0x4814 0E04
DDR0_IO_CTRL
DDR Memory Controller_0 IO Control Register
0x4814 0E08
DDR1_IO_CTRL
DDR Memory Controller_1 IO Control Register
290
Peripheral Information and Timings
REGISTER NAME
EMIF0/1 PHY Clock Gate Control Register
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-52. DDR-Related Control Module Registers (continued)
HEX ADDRESS RANGE
ACRONYM
0x4814 0E0C
DDR_VTP_CTRL_0
DDR0 VTP Control Register
REGISTER NAME
0x4814 0E10
DDR_VTP_CTRL_1
DDR1 VTP Control Register
8.13.4 DDR2/DDR3 Memory Controller Electrical Data/Timing
TI only supports board designs that follow the DDR2 and DDR3 Routing Specifications outlined in this
document. The switching characteristics and the timing diagram for the DDR2 memory controller are
shown in Table 8-53 and Figure 8-46.
Table 8-53. Switching Characteristics Over Recommended Operating Conditions for DDR2/DDR3 Memory
Controller (1)
OPP100/120/166
NO.
1
(1)
MIN
tc(DDR_CLK)
Cycle time, DDR[x]_CLK
DDR2 mode
2.5
DDR3 mode
1.876
MAX
UNIT
ns
The PLL_DDR Controller must be programmed such that the resulting DDR[x]_CLK clock frequency is within the specified range.
1
DDR[x]_CLK
Figure 8-46. DDR2/DDR3 Memory Controller Clock Timing
8.13.4.1 DDR2 Routing Specifications
8.13.4.1.1 DDR2 Interface
This section provides the timing specification for the DDR2 interface as a PCB design and manufacturing
specification. The design rules constrain PCB trace length, PCB trace skew, signal integrity, cross-talk,
and signal timing. These rules, when followed, result in a reliable DDR2 memory system without the need
for a complex timing closure process. For more information regarding the guidelines for using this DDR2
specification, see the Understanding TI’s PCB Routing Rule-Based DDR Timing Specification Application
Report (Literature Number: SPRAAV0).
8.13.4.1.1.1 DDR2 Interface Schematic
Figure 8-47 shows the DDR2 interface schematic for a x32 DDR2 memory system. In Figure 8-48 the x16
DDR2 system schematic is identical except that the high-word DDR2 device is deleted.
When not using all or part of a DDR2 interface, the proper method of handling the unused pins is to tie off
the DDR[x]_DQS[n] pins to the corresponding DVDD_DDR[x] supply via a 1k-Ω resistor and pulling the
DDR[x]_DQS[n] pins to ground via a 1k-Ω resistor. This needs to be done for each byte not used. Also,
include the 50-Ω pulldown for DDR[x]_VTP. The DVDD_DDR[x] and VREFSSTL_DDR[x] power supply
pins need to be connected to their respective power supplies even if DDR[x] is not being used. All other
DDR interface pins can be left unconnected. Note that the supported modes for use of the DDR EMIF are
32-bits wide, 16-bits wide, or not used.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
291
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
DDR2
DDR[x]_D[0]
DQ0
DDR[x]_D[7]
DDR[x]_DQM[0]
DDR[x]_DQS[0]
DQ7
LDM
LDQS
DDR[x]_DQS[0]
DDR[x]_D[8]
LDQS
DQ8
DDR[x]_D[15]
DDR[x]_DQM[1]
DDR[x]_DQS[1]
DQ15
UDM
UDQS
DDR[x]_DQS[1]
DDR[x]_ODT[0]
UDQS
ODT
T0
DDR2
DDR_ODT1
NC
ODT
DDR_D16
DQ0
DDR[x]_D[23
DDR[x]_DQM[2]
DDR[x]_DQS[2]
DDR[x]_DQS[2]
DDR[x]_D[24]
DQ7
LDM
LDQS
LDQS
DQ8
DDR[x]_D[31]
DDR[x]_DQM[3]
DDR[x]_DQS[3]
DDR[x]_DQS[3]
DQ15
UDM
UDQS
UDQS
DDR[x]_BA[0]
T0
BA0
BA0
DDR[x]_BA[2]
DDR[x]_A[0]
T0
T0
BA2
A0
BA2
A0
DDR[x]_A[14]
DDR[x]_CS[0]
T0
T0
NC
T0
T0
A14
CS
A14
CS
CAS
RAS
CAS
T0
T0
T0
T0
WE
CKE
CK
CK
VREF
WE
CKE
CK
CK
VREF
DDR[x]_CS[1]
DDR[x]_CAS
DDR[x]_RAS
DDR[x]_WE
DDR[x]_CKE
DDR[x]_CLK
DDR[x]_CLK
VREFSSTL_DDR[x]
0.1 µF
DDR[x]_RST
(B)
(B)
0.1 µF
(A)
Vio 1.8
RAS
VREF
0.1 µF
0.1 µF
VREF
1 K Ω 1%
VREF
(B)
0.1 µF
1 K Ω 1%
NC
DDR[x]_VTP
50 Ω (±2%)
T0
A.
B.
Termination is required. See terminator comments.
Vio1.8 is the power supply for the DDR2 memories and the DM814x DDR2 interface.
One of these capacitors can be eliminated if the divider and its capacitors are placed near a VREF pin.
Figure 8-47. 32-Bit DDR2 High-Level Schematic
292
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
DDR2
DDR[x]_D[0]
DQ0
DDR[x]_D[7]
DDR[x]_DQM[0]
DDR[x]_DQS[0]
DQ7
LDM
LDQS
DDR[x]_DQS[0]
DDR[x]_D[8]
LDQS
DQ8
DDR[x]_D[15]
DDR[x]_DQM[1]
DDR[x]_DQS[1]
DDR[x]_DQS[1]
DQ15
UDM
UDQS
UDQS
DDR[x]_ODT[0]
DDR[x]_ODT[1]
DDR[x]_D[16]
T0
NC
NC
DDR[x]_D[23]
DDR[x]_DQM[2]
NC
NC
1 KΩ
DDR[x]_D[24]
NC
1 KΩ
DDR[x]_D[31]
DDR[x]_DQM[3]
DDR[x]_DQS[3]
DDR[x]_DQS[3]
NC
NC
ODT
(A)
Vio 1.8
DDR[x]_DQS[2]
DDR[x]_DQS[2]
(A)
Vio 1.8
1 KΩ
1 KΩ
DDR[x]_BA[0]
T0
BA0
DDR[x]_BA[2]
DDR[x]_A[0]
T0
T0
BA2
A0
DDR[x]_A[14]
DDR[x]_CS[0]
DDR[x]_CS[1]
DDR[x]_CAS
T0
T0
NC
T0
T0
T0
T0
T0
T0
A14
CS
DDR[x]_RAS
DDR[x]_WE
DDR[x]_CKE
DDR[x]_CLK
DDR[x]_CLK
CAS
VREFSSTL_DDR[x]
VREF
0.1 µF
DDR[x]_RST
(A)
Vio 1.8
RAS
WE
CKE
CK
CK
(B)
0.1 µF
0.1 µF
VREF
1 K Ω 1%
VREF
(B)
0.1 µF
1 K Ω 1%
NC
DDR[x]_VTP
50 Ω (±2%)
T0
A.
B.
Termination is required. See terminator comments.
Vio1.8 is the power supply for the DDR2 memories and the DM814x DDR2 interface.
One of these capacitors can be eliminated if the divider and its capacitors are placed near a VREF pin.
Figure 8-48. 16-Bit DDR2 High-Level Schematic
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
293
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.13.4.1.1.2 Compatible JEDEC DDR2 Devices
Table 8-54 shows the parameters of the JEDEC DDR2 devices that are compatible with this interface.
Generally, the DDR2 interface is compatible with x16 DDR2-800 speed grade DDR2 devices.
Table 8-54. Compatible JEDEC DDR2 Devices (Per Interface)
NO.
PARAMETER
MIN
MAX
UNIT
1
JEDEC DDR2 device speed grade (1)
2
JEDEC DDR2 device bit width
x16
x16
3
JEDEC DDR2 device count (2)
1
2
Devices
4
JEDEC DDR2 device ball count (3)
84
92
Balls
(1)
(2)
(3)
DDR2-800
Bits
Higher DDR2 speed grades are supported due to inherent JEDEC DDR2 backwards compatibility.
One DDR2 device is used for a 16-bit DDR2 memory system. Two DDR2 devices are used for a 32-bit DDR2 memory system.
The 92-ball devices are retained for legacy support. New designs will migrate to 84-ball DDR2 devices. Electrically, the 92- and 84-ball
DDR2 devices are the same.
8.13.4.1.1.3 PCB Stackup
The minimum stackup required for routing the DM814x device is a six-layer stackup as shown in Table 855. Additional layers may be added to the PCB stackup to accommodate other circuitry or to reduce the
size of the PCB footprint.
Table 8-55. Minimum PCB Stackup
294
LAYER
TYPE
DESCRIPTION
1
Signal
Top routing mostly horizontal
2
Plane
Ground
3
Plane
Power
4
Signal
Internal routing
5
Plane
Ground
6
Signal
Bottom routing mostly vertical
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Complete stackup specifications are provided in Table 8-56.
Table 8-56. PCB Stackup Specifications
NO.
PARAMETER
6
2
Signal routing layers
3
3
Full ground layers under DDR2 routing region
2
4
Number of ground plane cuts allowed within DDR routing region
5
Number of ground reference planes required for each DDR2 routing layer
6
Number of layers between DDR2 routing layer and reference ground plane
7
PCB routing feature size
4
8
PCB trace width, w
4
9
PCB BGA escape via pad size (1)
PCB BGA escape via hole size
11
Processor BGA pad size
13
Single-ended impedance, Zo
14
Impedance control (2)
(2)
TYP
PCB routing/plane layers
10
(1)
MIN
1
MAX
UNIT
0
1
0
18
(1)
Mils
Mils
20
10
Mils
0.4
50
Z-5
Z
Mils
mm
75
Ω
Z+5
Ω
A 20/10 via may be used if enough power routing resources are available. An 18/10 via allows for more flexible power routing to the
processor.
Z is the nominal singled-ended impedance selected for the PCB specified by item 13.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
295
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.13.4.1.1.4 Placement
Figure 8-49 shows the required placement for the processor as well as the DDR2 devices. The
dimensions for this figure are defined in Table 8-57. The placement does not restrict the side of the PCB
on which the devices are mounted. The ultimate purpose of the placement is to limit the maximum trace
lengths and allow for proper routing space. For a 16-bit DDR memory system, the high-word DDR2 device
is omitted from the placement.
Recommended DDR2 Device
Orientation
X
X1
A1
X1
X1
OFFSET OFFSET
DDR2
Controller
Y
A1
Figure 8-49. DM814x Device and DDR2 Device Placement
Table 8-57. Placement Specifications
NO.
PARAMETER
1
X+Y
2
X' (1) (2)
3
X' Offset (1) (2)
4
DDR2 keepout region (4)
5
Clearance from non-DDR2 signal to DDR2 keepout region (5)
(1)
(2)
(3)
(4)
(5)
296
MIN
(1) (2)
(3)
4
MAX
UNIT
1660
Mils
1280
Mils
650
Mils
w
For dimension definitions, see Figure 8-47.
Measurements from center of processor to center of DDR2 device.
For 16-bit memory systems, it is recommended that X' offset be as small as possible.
DDR2 keepout region to encompass entire DDR2 routing area.
Non-DDR2 signals allowed within DDR2 keepout region provided they are separated from DDR2 routing layers by a ground plane.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.13.4.1.1.5 DDR2 Keepout Region
The region of the PCB used for the DDR2 circuitry must be isolated from other signals. The DDR2
keepout region is defined for this purpose and is shown in Figure 8-50. The size of this region varies with
the placement and DDR routing. Additional clearances required for the keepout region are shown in
Table 8-57.
A1
DDR2 Device
A1
A1
DDR2 Controller
A1
Figure 8-50. DDR2 Keepout Region
NOTE
The region shown in should encompass all the DDR2 circuitry and varies depending on
placement. Non-DDR2 signals should not be routed on the DDR signal layers within the
DDR2 keepout region. Non-DDR2 signals may be routed in the region, provided t hey are
routed on layers separated from DDR2 signal layers by a ground layer. No breaks should be
allowed in the reference ground layers in this region. In addition, the 1.8-V power plane
should cover the entire keepout region. Routes for the two DDR interfaces must be
separated by at least 4x; the more separation, the better.
8.13.4.1.1.6 Bulk Bypass Capacitors
Bulk bypass capacitors are required for moderate speed bypassing of the DDR2 and other circuitry.
Table 8-58 contains the minimum numbers and capacitance required for the bulk bypass capacitors. Note
that this table only covers the bypass needs of the DDR2 interfaces and DDR2 device. Additional bulk
bypass capacitance may be needed for other circuitry.
Table 8-58. Bulk Bypass Capacitors
No.
(1)
(2)
Parameter
Min
Max
Unit
1
DVDD18 bulk bypass capacitor count (1)
6
Devices
2
DVDD18 bulk bypass total capacitance
60
μF
1
Devices
(1)
3
DDR#1 bulk bypass capacitor count
4
DDR#1 bulk bypass total capacitance (1)
5
DDR#2 bulk bypass capacitor count (2)
6
DDR#2 bulk bypass total capacitance (1) (2)
10
μF
1
Devices
10
μF
These devices should be placed near the device they are bypassing, but preference should be given to the placement of the high-speed
(HS) bypass capacitors. Use half of these capacitors for DDR[0] and half for DDR[1].
Only used on 32-bit wide DDR2 memory systems.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
297
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.13.4.1.1.7 High-Speed Bypass Capacitors
High-speed (HS) bypass capacitors are critical for proper DDR2 interface operation. It is particularly
important to minimize the parasitic series inductance of the HS bypass capacitors, processor/DDR power,
and processor/DDR ground connections. Table 8-59 contains the specification for the HS bypass
capacitors as well as for the power connections on the PCB.
Table 8-59. High-Speed Bypass Capacitors
NO.
PARAMETER
MIN
1
HS bypass capacitor package size (1)
2
Distance from HS bypass capacitor to device being bypassed
3
Number of connection vias for each HS bypass capacitor (2)
2
4
Trace length from bypass capacitor contact to connection via
1
5
Number of connection vias for each processor power/ground ball
1
6
Trace length from processor power/ground ball to connection via
7
Number of connection vias for each DDR2 device power/ground ball
8
Trace length from DDR2 device power/ground ball to connection via
9
DVDD18 HS bypass capacitor count (3) (4)
40
10
DVDD18 HS bypass capacitor total capacitance (5)
2.4
11
DDR device HS bypass capacitor count (6) (7)
12
DDR device HS bypass capacitor total capacitance (7)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
MAX
UNIT
0402
10 Mils
250
30
1
Mils
Vias
35
0.4
Mils
Vias
35
8
Mils
Vias
Mils
Devices
μF
Devices
μF
LxW, 10-mil units, that is, a 0402 is a 40x20-mil surface-mount capacitor.
An additional HS bypass capacitor can share the connection vias only if it is mounted on the opposite side of the board.
These devices should be placed as close as possible to the device being bypassed.
Use half of these capacitors for DDR[0] and half for DDR[1].
Use half of these capacitors for DDR[0] and half for DDR[1].
These devices should be placed as close as possible to the device being bypassed.
Per DDR device.
8.13.4.1.1.8 Net Classes
Table 8-60 lists the clock net classes for the DDR2 interface. Table 8-61 lists the signal net classes, and
associated clock net classes, for the signals in the DDR2 interface. These net classes are used for the
termination and routing rules that follow.
Table 8-60. Clock Net Class Definitions
CLOCK NET CLASS
PROCESSOR PIN NAMES
CK
DDR[x]_CLK/DDR[x]_CLK
DQS0
DDR[x]_DQS[0]/DDR[x]_DQS[0]
DQS1
DDR[x]_DQS[1]/DDR[x]_DQS[1]
DQS2 (1)
DDR[x]_DQS[2]/DDR[x]_DQS[2]
(1)
DDR[x]_DQS[3]/DDR[x]_DQS[3]
DQS3
(1)
298
Only used on 32-bit wide DDR2 memory systems.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-61. Signal Net Class Definitions
CLOCK NET CLASS
ASSOCIATED CLOCK
NET CLASS
ADDR_CTRL
CK
DQ0
DQS0
DDR[x]_D[7:0], DDR[x]_DQM[0]
DQ1
DQS1
DDR[x]_D[15:8], DDR[x]_DQM[1]
DQ2 (1)
DQS2
DDR[x]_D[23:16], DDR[x]_DQM[2]
(1)
DQS3
DDR[x]_D[31:24], DDR[x]_DQM[3]
DQ3
(1)
PROCESSOR PIN NAMES
DDR[x]_BA[2:0], DDR[x]_A[14:0], DDR[x]_CS[x], DDR[x]_CAS, DDR[x]_RAS,
DDR[x]_WE, DDR[x]_CKE, DDR[x]_ODT[x]
Only used on 32-bit wide DDR2 memory systems.
8.13.4.1.1.9 DDR2 Signal Termination
Signal terminators are required in CK and ADDR_CTRL net classes. Serial terminators may be used on
data lines to reduce EMI risk; however, serial terminations are the only type permitted. ODTs are
integrated on the data byte net classes. They should be enabled to ensure signal integrity.Table 8-62
shows the specifications for the series terminators.
Table 8-62. DDR2 Signal Terminations
NO.
1
(1)
(2)
(3)
(4)
(5)
PARAMETER
MIN
CK net class (1) (2)
TYP
0
(1) (2) (3) (4)
2
ADDR_CTRL net class
3
Data byte net classes (DQS0-DQS3, DQ0-DQ3) (5)
0
0
22
MAX
UNIT
10
Ω
Zo
Ω
Zo
Ω
Only series termination is permitted, parallel or SST specifically disallowed on board.
Only required for EMI reduction.
Terminator values larger than typical only recommended to address EMI issues.
Termination value should be uniform across net class.
No external terminations allowed for data byte net classes. ODT is to be used.
8.13.4.1.1.10 VREFSSTL_DDR Routing
VREFSSTL_DDR is used as a reference by the input buffers of the DDR2 memories as well as the
processor. VREF is intended to be half the DDR2 power supply voltage and should be created using a
resistive divider as shown in Figure 8-48. Other methods of creating VREF are not recommended.
Figure 8-51 shows the layout guidelines for VREF.
VREF Nominal Max Trace
width is 20 mils
VREF Bypass Capacitor
A1
+
DDR2 Device
A1
+
DDR2 Controller
Neck down to minimum in BGA escape
regions is acceptable. Narrowing to
accomodate via congestion for short
distances is also acceptable. Best
performance is obtained if the width
of VREF is maximized.
Figure 8-51. VREF Routing and Topology
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
299
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.13.4.1.2 DDR2 CK and ADDR_CTRL Routing
Figure 8-52 shows the topology of the routing for the CK and ADDR_CTRL net classes. The route is a
balanced T as it is intended that the length of segments B and C be equal. In addition, the length of A
(A'+A'') should be maximized.
A1
A1
C
B
T
A´
DDR2
Controller
A´´
A = A´ + A´´
Figure 8-52. CK and ADDR_CTRL Routing and Topology
Table 8-63. CK and ADDR_CTRL Routing Specification
NO.
PARAMETER
MIN
(1)
TYP
MAX
UNIT
1
Center-to-center CK-CK spacing
2w
2
CK/CK skew (1)
25
Mils
3
CK A-to-B/A-to-C skew length mismatch (2)
25
Mils
4
CK B-to-C skew length mismatch
25
Mils
5
Center-to-center CK to other DDR2 trace spacing (3)
6
CK/ADDR_CTRL nominal trace length (4)
CACLM+50
Mils
7
ADDR_CTRL-to-CK skew length mismatch
100
Mils
8
ADDR_CTRL-to-ADDR_CTRL skew length mismatch
100
Mils
9
Center-to-center ADDR_CTRL to other DDR2 trace spacing (3)
4w
10
Center-to-center ADDR_CTRL to other ADDR_CTRL trace spacing (3)
3w
11
ADDR_CTRL A-to-B/A-to-C skew length mismatch (2)
100
Mils
12
ADDR_CTRL B-to-C skew length mismatch
100
Mils
(1)
(2)
(3)
(4)
300
4w
CACLM-50
CACLM
The length of segment A = A' + A′′ as shown in Figure 8-52.
Series terminator, if used, should be located closest to the processor.
Center-to-center spacing is allowed to fall to minimum (w) for up to 500 mils of routed length to accommodate BGA escape and routing
congestion.
CACLM is the longest Manhattan distance of the CK and ADDR_CTRL net classes.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Figure 8-53 shows the topology and routing for the DQS and DQ net classes; the routes are point to point.
Skew matching across bytes is not needed nor recommended.
A1
T
A1
T
E0
E2
T
T
E1
DDR2
Controller
E3
Figure 8-53. DQS and DQ Routing and Topology
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
301
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-64. DQS and DQ Routing Specification
NO.
PARAMETER
MIN
1
Center-to-center DQS-DQSn spacing in E0|E1|E2|E3
2
DQS-DQSn skew in E0|E1|E2|E3
3
Center-to-center DQS to other DDR2 trace spacing (1)
4
DQS/DQ nominal trace length
5
DQ-to-DQS skew length mismatch (2) (3) (4)
6
DQ-to-DQ skew length mismatch (2) (3) (4)
(2) (3) (4)
DQLM-50
Center-to-center DQ to other DDR2 trace spacing (1) (5)
4w
9
Center-to-center DQ to other DQ trace spacing (1) (6) (7)
3w
(2)
(3)
(4)
(5)
(6)
(7)
25
Mils
DQLM
DQLM+50
Mils
100
Mils
100
Mils
1
Vias
100
Mils
(2) (3) (4)
DQ-to-DQ/DQS via count mismatch
DQ/DQS E skew length mismatch
UNIT
4w
8
10
MAX
2w
7
(1)
TYP
(2) (3) (4)
Center-to-center spacing is allowed to fall to minimum (w) for up to 500 mils of routed length to accommodate BGA escape and routing
congestion.
A 16-bit DDR memory system has two sets of data net classes; one for data byte 0, and one for data byte 1, each with an associated
DQS (2 DQSs) per DDR EMIF used.
A 32-bit DDR memory system has four sets of data net classes; one each for data bytes 0 through 3, and each associated with a DQS
(4 DQSs) per DDR EMIF used.
There is no need, and it is not recommended, to skew match across data bytes; that is, from DQS0 and data byte 0 to DQS1 and data
byte 1.
DQs from other DQS domains are considered other DDR2 trace.
DQs from other data bytes are considered other DDR2 trace.
DQLM is the longest Manhattan distance of each of the DQS and DQ net classes.
8.13.4.2 DDR3 Routing Specifications
8.13.4.2.1 DDR3 versus DDR2
This specification only covers PCB designs that utilize DDR3 memory. PCB designs using other types of
DDR memory should follow the specification appropriate for that type of memory. It is currently not
possible to design a single PCB that supports multiple types of DDR memory.
8.13.4.2.2 DDR3 EMIFs
A processor may contain more than one EMIF. This specification covers only one EMIF and needs to be
implemented for each additional EMIF. Requirements are identical between the EMIFs, however, the PCB
layouts will most likely be different.
8.13.4.2.3 DDR3 Device Combinations
Since there are several possible combinations of device counts and single- or dual-side mounting,
Table 8-65 summarizes the supported device configurations.
Table 8-65. Supported DDR3 Device Combinations (1)
NUMBER OF DDR3 DEVICES
DDR3 DEVICE WIDTH (BITS)
MIRRORED?
DDR3 EMIF WIDTH (BITS)
1
16
N
16
(1)
(2)
(3)
302
Y
(2)
2
8
2
16
N
16
32
2
16
Y (2)
32
4
8
N
32
4
8
Y (3)
32
This table is per EMIF.
Two DDR3 devices are mirrored when one device is placed on the top of the board and the second device is placed on the bottom of
the board.
This is two mirrored pairs of DDR3 devices.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.13.4.2.4 DDR3 Interface Schematic
The DDR3 interface schematic varies, depending upon the width of the DDR3 devices used and the width
of the bus used (16 or 32 bits). General connectivity is straightforward and very similar. 16-bit DDR
devices look like two 8-bit devices. Figure 8-54 and Figure 8-55 show the schematic connections for 32-bit
interfaces using x16 and x8 devices.
Note that a 16-bit wide interface schematic is practically identical to the 32-bit interface; only the high-word
DDR memories are removed.
When not using all or part of a DDR3 interface, the proper method of handling the unused pins is to tie off
the DDR[x]_DQS[n] pins to the corresponding DVDD_DDR[x] supply via a 1-kΩ resistor and pulling the
DDR[x]_DQS[n] pins to ground via a 1k-Ω resistor. This needs to be done for each byte not used.
Although these signals have internal pullups and pulldowns, external pullups and pulldowns provide
additional protection against external electrical noise causing activity on the signals.Also, include the 50-Ω
pulldown for DDR[x]_VTP. The DVDD_DDR[x] and VREFSSTL_DDR[x] power supply pins need to be
connected to their respective power supplies even if DDR[x] is not being used. All other DDR interface
pins can be left unconnected. Note that the supported modes for use of the DDR EMIF are 32 bits wide,
16 bits wide, or not used.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
303
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
32-bit DDR3 EMIF
DDR[x]_ODT[1]
DDR[x]_CS[1]
16-Bit DDR3
Devices
NC
NC
DDR[x]_D[31]
DQ15
8
DDR[x]_D[24]
DQ8
DDR[x]_DQM[3]
DDR[x]_DQS[3]
DDR[x]_DQS[3]
UDM
UDQS
UDQS
DDR[x]_D[23]
DQ7
8
DDR[x]_D[16]
D08
DDR[x]_DQM[2]
DDR[x]_DQS[2]
DDR[x]_DQS[2]
LDM
LDQS
LDQS
DDR[x]_D[15]
DQ15
8
DDR[x]_D[8]
DQ8
DDR[x]_DQM[1]
DDR[x]_DQS[1]
DDR[x]_DQS[1]
UDM
UDQS
UDQS
DDR[x]_D[7]
DQ7
8
DDR[x]_D[0]
DQ0
DDR[x]_DQM[0]
DDR[x]_DQS[0]
DDR[x]_DQS[0]
LDM
LDQS
LDQS
DDR[x]_CLK
DDR[x]_CLK
DDR[x]_ODT[0]
DDR[x]_CS[0]
DDR[x]_BA[0]
DDR[x]_BA[1]
DDR[x]_BA[2]
DDR[x]_A[0]
Zo
CK
CK
CK
CK
ODT
CS
BA0
BA1
BA2
ODT
CS
BA0
BA1
BA2
A0
A0
Zo
A14
A14
Zo
CAS
RAS
WE
CKE
RST
ZQ
VREFDQ
VREFCA
CAS
RAS
WE
CKE
RST
0.1 µF
DDR_1V5
Zo
DDR_VTT
15
DDR[x]_A[14]
DDR[x]_CAS
DDR[x]_RAS
DDR[x]_WE
DDR[x]_CKE
DDR[x]_RST
ZQ
VREFSSTL_DDR[x]
0.1 µF
0.1 µF
DDR_VREF
ZQ
VREFDQ
VREFCA
ZQ
0.1 µF
DDR[x]_VTP
50 Ω (±2%)
Zo
ZQ
Termination is required. See terminator comments.
Value determined according to the DDR memory device data sheet.
Figure 8-54. 32-Bit, One-Bank DDR3 Interface Schematic Using Two 16-Bit DDR3 Devices
304
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
32-bit DDR3 EMIF
DDR[x]_ODT[1]
DDR[x]_CS[1]
8-Bit DDR3
Devices
NC
NC
8-Bit DDR3
Devices
DDR[x]_D[31]
DQ7
8
DDR[x]_D[24]
DQ0
DDR[x]_DQM[3]
NC
DDR[x]_DQS[3]
DDR[x]_DQS[3]
DDR[x]_D[23]
DM/TQS
TDQS
DQS
DQS
DQ7
8
DDR[x]_D[16]
DQ0
DDR[x]_DQM[2]
NC
DDR[x]_DQS[2]
DDR[x]_DQS[2]
DDR[x]_D[15]
DM/TQS
TDQS
DQS
DQS
DQ7
8
DDR[x]_D[8]
DQ0
DDR[x]_DQM[1]
NC
DDR[x]_DQS[1]
DDR[x]_DQS[1]
DDR[x]_D[7]
DM/TQS
TDQS
DQS
DQS
DQ7
8
DDR[x]_D[0]
DQ0
DDR[x]_DQM[0]
NC
DDR[x]_DQS[0]
DDR[x]_DQS[0]
DDR[x]_CLK
DDR[x]_CLK
DM/TQS
TDQS
DQS
DQS
CK
CK
DDR[x]_ODT[0]
DDR[x]_CS[0]
DDR[x]_BA[0]
DDR[x]_BA[1]
DDR[x]_BA[2]
DDR[x]_A[0]
Zo
CK
CK
CK
CK
0.1 µF
CK
CK
DDR_1V5
Zo
ODT
CS
BA0
BA1
BA2
ODT
CS
BA0
BA1
BA2
ODT
CS
BA0
BA1
BA2
ODT
CS
BA0
BA1
BA2
A0
A0
A0
A0
Zo
A14
A14
A14
A14
Zo
CAS
RAS
WE
CKE
RST
ZQ
VREFDQ
VREFCA
CAS
RAS
WE
CKE
RST
CAS
RAS
WE
CKE
RST
ZQ
VREFDQ
VREFCA
CAS
RAS
WE
CKE
RST
DDR_VTT
15
DDR[x]_A[14]
DDR[x]_CAS
DDR[x]_RAS
DDR[x]_WE
DDR[x]_CKE
DDR[x]_RST
ZQ
VREFSSTL_DDR[x]
0.1 µF
0.1 µF
ZQ
VREFDQ
VREFCA
0.1 µF
ZQ
ZQ
0.1 µF
ZQ
VREFDQ
VREFCA
DDR_VREF
ZQ
0.1 µF
DDR[x]_VTP
50 Ω (±2%)
Zo
ZQ
Termination is required. See terminator comments.
Value determined according to the DDR memory device data sheet.
Figure 8-55. 32-Bit, One-Bank DDR3 Interface Schematic Using Four 8-Bit DDR3 Devices
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
305
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.13.4.2.4.1 Compatible JEDEC DDR3 Devices
Table 8-66 shows the parameters of the JEDEC DDR3 devices that are compatible with this interface.
Generally, the DDR3 interface is compatible with DDR3-1600 devices in the x8 or x16 widths.
Table 8-66. Compatible JEDEC DDR3 Devices (Per Interface)
NO.
PARAMETER
1
JEDEC DDR3 device speed grade (1)
2
JEDEC DDR3 device bit width
3
(1)
(2)
(3)
JEDEC DDR3 device count
MIN
MAX
DDR3-800
DDR31600 (2)
x8
x16
2
8
(3)
UNIT
Bits
Devices
DDR3 speed grade depends on desired clock rate. Data rate is 2x the clock rate. For DDR3-800, the clock rate is 400 MHz.
DDR3 devices with speed grades up to DDR3-1600 are supported; however, max clock rate will still be limited to 533 MHz as stated in
Switching Characteristics Over Recommended Operating Conditions for DDR3 Memory Controller.
For valid DDR3 device configurations and device counts, see Section 8.13.4.2.4, Figure 8-54, and Figure 8-55.
8.13.4.2.4.2 PCB Stackup
The minimum stackup for routing the DDR3 interface is a four-layer stack up as shown in Table 8-67.
Additional layers may be added to the PCB stackup to accommodate other circuitry, enhance SI/EMI
performance, or to reduce the size of the PCB footprint. A six-layer stackup is shown in Table 8-68.
Complete stackup specifications are provided in Table 8-69.
Table 8-67. Minimum PCB Stackup
LAYER
TYPE
DESCRIPTION
1
Signal
Top routing mostly vertical
2
Plane
Split power plane
3
Plane
Full ground plane
4
Signal
Bottom routing mostly horizontal
Table 8-68. Six-Layer PCB Stackup Suggestion
306
LAYER
TYPE
DESCRIPTION
1
Signal
Top routing mostly vertical
2
Plane
Ground
3
Plane
Split power plane
4
Plane
Split power plane or Internal routing
5
Plane
Ground
6
Signal
Bottom routing mostly horizontal
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-69. PCB Stackup Specifications
NO.
MIN
TYP
1
PCB routing/plane layers
PARAMETER
4
6
2
Signal routing layers
2
3
Full ground reference layers under DDR3 routing region (1)
MAX
1
(1)
4
Full 1.5-V power reference layers under the DDR3 routing region
5
Number of reference plane cuts allowed within DDR routing region (2)
0
6
Number of layers between DDR3 routing layer and reference plane (3)
0
7
PCB routing feature size
4
8
PCB trace width, w
4
13
Single-ended impedance, Zo
14
(1)
(2)
(3)
(4)
Impedance control
UNIT
1
50
(4)
Z-5
Z
Mils
Mils
75
Ω
Z+5
Ω
Ground reference layers are preferred over power reference layers. Be sure to include bypass caps to accommodate reference layer
return current as the trace routes switch routing layers.
No traces should cross reference plane cuts within the DDR routing region. High-speed signal traces crossing reference plane cuts
create large return current paths which can lead to excessive crosstalk and EMI radiation.
Reference planes are to be directly adjacent to the signal plane to minimize the size of the return current loop.
Z is the nominal singled-ended impedance selected for the PCB specified by item 13.
8.13.4.2.4.3 Placement
Figure 8-56 shows the required placement for the processor as well as the DDR3 devices. The
dimensions for this figure are defined in Table 8-70. The placement does not restrict the side of the PCB
on which the devices are mounted. The ultimate purpose of the placement is to limit the maximum trace
lengths and allow for proper routing space. For a 16-bit DDR memory system, the high-word DDR3
device(s) are omitted from the placement.
X1
X2
X2
X2
DDR3
Controller
Y
Figure 8-56. Placement Specifications
It is strongly recommended that high-speed bypass capacitors be placed and accommodated for during
the placement and route planning phase. It is very difficult to add bypass capacitors once the board has
been routed and significant rework may be required to meet the high-speed bypass capacitor
requirements in Section 8.13.4.2.4.6, High-Speed Bypass Capacitors if the proper planning is not done. A
particular challenge to placing bypass capacitors in congested areas is fitting the required vias. It is
suggested that each pair of vias support two bypass capacitors by mounting one capacitor on the top of
the board and other on the bottom. Do not share vias between capacitors mounted on the same side of
the PCB. Another suggestion is to line up the vias for the bypass capacitors for the processor in rows
forming channels to allow the signals to escape.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
307
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-70. Placement Specifications
NO.
PARAMETER
MIN
1
X1 (1) (2) (3)
2
X2 (1) (2)
3
Y Offset (1) (2) (3)
4
DDR3 keepout region
5
Clearance from non-DDR3 signal to DDR3 keepout region (4) (5) (6)
(1)
(2)
(3)
(4)
(5)
(6)
4
MAX
UNIT
1000
Mils
600
Mils
1500
Mils
w
For dimension definitions, see Figure 8-56.
Measurements from center of processor to center of DDR3 device.
Minimizing X1 and Y improves timing margins.
w is defined as the signal trace width.
Non-DDR3 signals allowed within DDR3 keepout region provided they are separated from DDR3 routing layers by a ground plane.
If a device has more than one DDR controller, the signals from the other controller(s) are considered non-DDR3 and should be
separated by this specification.
8.13.4.2.4.4 DDR3 Keepout Region
The region of the PCB used for DDR3 circuitry must be isolated from other signals. The DDR3 keepout
region is defined for this purpose and is shown in Figure 8-57. The size of this region varies with the
placement and DDR routing. Additional clearances required for the keepout region are shown in Table 870. Non-DDR3 signals should not be routed on the DDR signal layers within the DDR3 keepout region.
Non-DDR3 signals may be routed in the region, provided they are routed on layers separated from the
DDR signal layers by a ground layer. No breaks should be allowed in the reference ground layers in this
region. In addition, the 1.5-V DDR3 power plane should cover the entire keepout region. Also note that if
there is more than one DDR controller, the signals from each controller need to be separated from each
other by the specification in Table 8-70, item 5. Each DDR controller should have its own DDR keepout
region.
DDR3 Controllers
DDR[1] Keep Out Region
DDR[0] Keep Out Region
Encompasses Entire DDR[1] Routing Area
Encompasses Entire DDR[0] Routing Area
Figure 8-57. DDR3 Keepout Region
Figure 8-57 is an example of a processor with two DDR controllers. Processors with a single DDR
controler will have only one DDR keepout region. Each DDR controller should have its own keepout
region.
8.13.4.2.4.5 Bulk Bypass Capacitors
Bulk bypass capacitors are required for moderate speed bypassing of the DDR3 and other circuitry.
Table 8-71 contains the minimum numbers and capacitance required for the bulk bypass capacitors. Note
that this table only covers the bypass needs of the DDR3 controllers and DDR3 device(s). Additional bulk
bypass capacitance may be needed for other circuitry.
308
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-71. Bulk Bypass Capacitors Per DDR3 EMIF
NO.
PARAMETER
MIN
MAX
UNIT
1
DDR_1V5 bulk bypass capacitor count (1)
3
Devices
2
DDR_1V5 bulk bypass total capacitance
70
μF
(1)
These devices should be placed near the devices they are bypassing, but preference should be given to the placement of the highspeed (HS) bypass capacitors and DDR3 signal routing.
8.13.4.2.4.6 High-Speed Bypass Capacitors
High-speed (HS) bypass capacitors are critical for proper DDR3 interface operation. It is particularly
important to minimize the parasitic series inductance of the HS bypass capacitors, processor/DDR power,
and processor/DDR ground connections. Table 8-72 contains the specification for the HS bypass
capacitors as well as for the power connections on the PCB. Generally speaking, it is good to:
1. Fit as many HS bypass capacitors as possible.
2. Minimize the distance from the bypass cap to the pins/balls being bypassed.
3. Use the smallest physical sized capacitors possible with the highest capacitance readily available.
4. Connect the bypass capacitor pads to their vias using the widest traces possible and using the largest
hole size via possible.
5. Minimize via sharing. Note the limits on via sharing shown in Table 8-72.
Table 8-72. High-Speed Bypass Capacitors
NO.
PARAMETER
MIN
1
HS bypass capacitor package size (1)
2
Distance, HS bypass capacitor to processor being bypassed (2) (3) (4)
(5)
3
Processor DDR_1V5 HS bypass capacitor count
4
Processor DDR_1V5 HS bypass capacitor total capacitance
TYP
MAX
UNIT
201
402
10 Mils
400
Mils
35
Per
DDR3
EMIF
5
μF
(6)
5
Number of connection vias for each device power/ground ball
6
Trace length from device power/ground ball to connection via (2)
7
Distance, HS bypass capacitor to DDR device being bypassed (7)
(8)
Vias
35
8
DDR3 device HS bypass capacitor count
9
DDR3 device HS bypass capacitor total capacitance (8)
0.85
10
Number of connection vias for each HS capacitor (9) (10)
2
11
Trace length from bypass capacitor connect to connection via (2) (10)
12
Number of connection vias for each DDR3 device power/ground ball (11)
13
Trace length from DDR3 device power/ground ball to connection via (2) (9)
70
Mils
150
Mils
12
Devices
μF
Vias
35
100
1
Mils
Vias
35
60
Mils
(1)
(2)
(3)
(4)
LxW, 10-mil units, i.e., a 0402 is a 40x20-mil surface-mount capacitor.
Closer/shorter is better.
Measured from the nearest processor power/ground ball to the center of the capacitor package.
Three of these capacitors should be located underneath the processor, between the cluster of DDR_1V5 balls and ground balls,
between the DDR interfaces on the package.
(5) Per DDR3 EMIF. For example, a processor with two DDR3 EMIFs would require 70 capacitors. The capacitors should be evenly
distributed near the Processor's DDR_1V5 pins.
(6) See the Via Channel™ escape for the processor package.
(7) Measured from the DDR3 device power/ground ball to the center of the capacitor package.
(8) Per DDR3 EMIF.
(9) An additional HS bypass capacitor can share the connection vias only if it is mounted on the opposite side of the board. No sharing of
vias is permitted on the same side of the board.
(10) An HS bypass capacitor may share a via with a DDR device mounted on the same side of the PCB. A wide trace should be used for the
connection and the length from the capacitor pad to the DDR device pad should be less than 150 mils.
(11) Up to a total of two pairs of DDR power/ground balls may share a via.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
309
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.13.4.2.4.6.1 Return Current Bypass Capacitors and Vias
If a power plane is used as a reference plane then additional bypass capacitors may be required to
accommodate the signal return currents. Care should be taken to minimize the layer transitions during
routing. If a layer transition is necessary, it is better to transition to a layer using the same reference plane.
If this cannot be accommodated, ensure there is a nearby path to allow the return currents to transition
between reference planes. Transitions from power reference planes to ground reference planes must go
through a bypass capacitor. Transition between different ground references or DVDD_DDR planes can go
through a connecting via. As many of these return current bypass capacitors or vias should be used as
possible. The goal is to minimize the size of the return current loops. Generally, this type of situation
happens where signals must transition from horizontal to vertical routing and vice-versa.
8.13.4.2.4.7 Net Classes
Table 8-73 lists the clock net classes for the DDR3 interface. Table 8-74 lists the signal net classes, and
associated clock net classes, for signals in the DDR3 interface. These net classes are used for the
termination and routing rules that follow.
Table 8-73. Clock Net Class Definitions
CLOCK NET CLASS
PROCESSOR PIN NAMES
CK
DDR[x]_CLK/DDR[x]_CLK
DQS0
DDR[x]_DQS[0]/DDR[x]_DQS[0]
DQS1
DDR[x]_DQS[1]/DDR[x]_DQS[1]
(1)
DDR[x]_DQS[2]/DDR[x]_DQS[2]
DQS3 (1)
DDR[x]_DQS[3]/DDR[x]_DQS[3]
DQS2
(1)
Only used on 32-bit wide DDR3 memory systems.
Table 8-74. Signal Net Class Definitions
CLOCK NET CLASS
ASSOCIATED CLOCK
NET CLASS
ADDR_CTRL
CK
DQ0
DQS0
DDR[x]_D[7:0], DDR[x]_DQM[0]
DQ1
DQS1
DDR[x]_D[15:8], DDR[x]_DQM[1]
DQ2 (1)
DQS2
DDR[x]_D[23:16], DDR[x]_DQM[2]
(1)
DQS3
DDR[x]_D[31:24], DDR[x]_DQM[3]
DQ3
(1)
PROCESSOR PIN NAMES
DDR[x]_BA[2:0], DDR[x]_A[14:0], DDR[x]_CS[x], DDR[x]_CAS, DDR[x]_RAS,
DDR[x]_WE, DDR[x]_CKE, DDR[x]_ODT[x]
Only used on 32-bit wide DDR3 memory systems.
8.13.4.2.4.8 DDR3 Signal Termination
Signal terminators are required for the CK and ADDR_CTRL net classes. The data lines are terminated by
ODT and, thus, the PCB traces should be unterminated. Detailed termination specifications are covered in
the routing rules in the following sections.
8.13.4.2.4.9 VREFSSTL_DDR Routing
VREFSSTL_DDR (VREF) is used as a reference by the input buffers of the DDR3 memories as well as
the processor. VREF is intended to be half the DDR3 power supply voltage and is typically generated with
the DDR3 1.5-V and VTT power supply. It should be routed as a nominal 20-mil wide trace with 0.1 µF
bypass capacitors near each device connection. Narrowing of VREF is allowed to accommodate routing
congestion.
310
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.13.4.2.4.10 VTT
Like VREF, the nominal value of the VTT supply is half the DDR3 supply voltage. Unlike VREF, VTT is
expected to source and sink current, specifically the termination current for the ADDR_CTRL net class
Thevinen terminators. VTT is needed at the end of the address bus and it should be routed as a power
sub-plane. VTT should be bypassed near the terminator resistors.
8.13.4.2.4.11 CK and ADDR_CTRL Topologies and Routing Definition
The CK and ADDR_CTRL net classes are routed similarly and are length matched to minimize skew
between them. CK is a bit more complicated because it runs at a higher transition rate and is differential.
The following subsections show the topology and routing for various DDR3 configurations for CK and
ADDR_CTRL. Only the components shown in the topologies are allowed. Items such as test points and
additional terminations are specifically disallowed. The figures in the following subsections define the
terms for the routing specification detailed in Table 8-75.
Care should be taken to minimize layer transitions during routing. If a layer transition is necessary, it is
better to transition to a layer using the same reference plane. If this cannot be accommodated, ensure
there are nearby ground vias to allow the return currents to transition between reference planes if both
reference planes are ground or DVDD_DDR. Ensure there are nearby bypass capacitors to allow the
return currents to transition between reference planes if one of the reference planes is ground. The goal is
to minimize the size of the return current loops.
8.13.4.2.4.11.1 Four DDR3 Devices
Four DDR3 devices are supported on the DDR EMIF consisting of four x8 DDR3 devices arranged as one
bank (CS). These four devices may be mounted on a single side of the PCB, or may be mirrored in two
pairs to save board space at a cost of increased routing complexity and parts on the backside of the PCB.
8.13.4.2.4.11.2 CK and ADDR_CTRL Topologies, Four DDR3 Devices
Figure 8-58 shows the topology of the CK net classes and Figure 8-59 shows the topology for the
corresponding ADDR_CTRL net classes.
+ –
+ –
+ –
+ –
AS+
AS-
AS+
AS-
AS+
AS-
AS+
AS-
DDR Differential CK Input Buffers
Clock Parallel
Terminator
DDR_1V5
Rcp
A1
Processor
Differential Clock
Output Buffer
A2
A3
A4
A3
AT
Cac
+
–
Rcp
A1
A2
A3
A4
A3
0.1 µF
AT
Routed as Differential Pair
Figure 8-58. CK Topology for Four x8 DDR3 Devices
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
311
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Processor
Address and Control
Output Buffer
A1
A3
A2
AS
AS
AS
AS
DDR Address and Control Input Buffers
A3
A4
Address and Control
Terminator
Rtt
Vtt
AT
Figure 8-59. ADDR_CTRL Topology for Four x8 DDR3 Devices
8.13.4.2.4.11.3 CK and ADDR_CTRL Routing, Four DDR3 Devices
A1
A1
Figure 8-60 shows the CK routing for four DDR3 devices placed on the same side of the PCB. Figure 8-61
shows the corresponding ADDR_CTRL routing.
DDR_1V5
A3
A3
=
A4
A4
A3
A3
Rcp
Cac
Rcp
0.1 µF
AT
AT
AS+
AS-
A2
A2
Figure 8-60. CK Routing for Four Single-Side DDR3 Devices
312
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
A1
www.ti.com
Rtt
A3
=
A3
A4
AT
Vtt
AS
A2
Figure 8-61. ADDR_CTRL Routing for Four Single-Side DDR3 Devices
A1
A1
To save PCB space, the four DDR3 memories may be mounted as two mirrored pairs at a cost of
increased routing and assembly complexity. Figure 8-62 and Figure 8-63 show the routing for CK and
ADDR_CTRL, respectively, for four DDR3 devices mirrored in a two-pair configuration.
DDR_1V5
=
A4
A4
A3
A3
Rcp
Cac
Rcp
0.1 µF
AT
AT
AS+
AS-
A3
A3
A2
A2
Figure 8-62. CK Routing for Four Mirrored DDR3 Devices
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
313
TMS320DM8148, TMS320DM8147
www.ti.com
A1
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Rtt
A3
=
A3
A4
AT
Vtt
AS
A2
Figure 8-63. ADDR_CTRL Routing for Four Mirrored DDR3 Devices
8.13.4.2.4.11.4 Two DDR3 Devices
Two DDR3 devices are supported on the DDR EMIF consisting of two x8 DDR3 devices arranged as one
bank (CS), 16-bits wide, or two x16 DDR3 devices arranged as one bank (CS), 32-bits wide. These two
devices may be mounted on a single side of the PCB, or may be mirrored in a pair to save board space at
a cost of increased routing complexity and parts on the backside of the PCB.
8.13.4.2.4.11.5 CK and ADDR_CTRL Topologies, Two DDR3 Devices
Figure 8-64 shows the topology of the CK net classes and Figure 8-65 shows the topology for the
corresponding ADDR_CTRL net classes.
+ –
+ –
AS+
AS-
AS+
AS-
DDR Differential CK Input Buffers
Clock Parallel
Terminator
DDR_1V5
Rcp
A1
Processor
Differential Clock
Output Buffer
A2
A3
AT
Cac
+
–
Rcp
A1
A2
A3
0.1 µF
AT
Routed as Differential Pair
Figure 8-64. CK Topology for Two DDR3 Devices
314
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Processor
Address and Control
Output Buffer
A1
AS
AS
DDR Address and Control Input Buffers
A3
A2
Address and Control
Terminator
Rtt
Vtt
AT
Figure 8-65. ADDR_CTRL Topology for Two DDR3 Devices
8.13.4.2.4.11.6 CK and ADDR_CTRL Routing, Two DDR3 Devices
A1
A1
Figure 8-66 shows the CK routing for two DDR3 devices placed on the same side of the PCB. Figure 8-67
shows the corresponding ADDR_CTRL routing.
DDR_1V5
A3
A3
=
Rcp
Cac
Rcp
0.1 µF
AT
AT
AS+
AS-
A2
A2
Figure 8-66. CK Routing for Two Single-Side DDR3 Devices
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
315
TMS320DM8148, TMS320DM8147
www.ti.com
A1
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Rtt
A3
=
Vtt
AT
AS
A2
Figure 8-67. ADDR_CTRL Routing for Two Single-Side DDR3 Devices
A1
A1
To save PCB space, the two DDR3 memories may be mounted as a mirrored pair at a cost of increased
routing and assembly complexity. Figure 8-68 and Figure 8-69 show the routing for CK and ADDR_CTRL,
respectively, for two DDR3 devices mirrored in a single-pair configuration.
DDR_1V5
=
Rcp
Cac
Rcp
0.1 µF
AT
AT
AS+
AS-
A3
A3
A2
A2
Figure 8-68. CK Routing for Two Mirrored DDR3 Devices
316
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
A1
www.ti.com
Rtt
A3
=
Vtt
AT
AS
A2
Figure 8-69. ADDR_CTRL Routing for Two Mirrored DDR3 Devices
8.13.4.2.4.11.7 One DDR3 Device
A single DDR3 device is supported on the DDR EMIF consisting of one x16 DDR3 device arranged as
one bank (CS), 16-bits wide.
8.13.4.2.4.11.8 CK and ADDR_CTRL Topologies, One DDR3 Device
Figure 8-70 shows the topology of the CK net classes and Figure 8-71 shows the topology for the
corresponding ADDR_CTRL net classes.
DDR Differential CK Input Buffer
AS+
AS-
+ –
Clock Parallel
Terminator
DDR_1V5
Rcp
A1
Processor
Differential Clock
Output Buffer
A2
AT
Cac
+
–
Rcp
A1
A2
0.1 µF
AT
Routed as Differential Pair
Figure 8-70. CK Topology for One DDR3 Device
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
317
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
AS
DDR Address and Control Input Buffers
Processor
Address and Control
Output Buffer
A1
Address and Control
Terminator
Rtt
AT
Vtt
A2
Figure 8-71. ADDR_CTRL Topology for One DDR3 Device
8.13.4.2.4.11.9 CK and ADDR/CTRL Routing, One DDR3 Device
A1
A1
Figure 8-72 shows the CK routing for one DDR3 device placed on the same side of the PCB. Figure 8-73
shows the corresponding ADDR_CTRL routing.
DDR_1V5
Rcp
Cac
Rcp
0.1 µF
AT
AT
=
AS+
AS-
A2
A2
Figure 8-72. CK Routing for One DDR3 Device
318
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
A1
www.ti.com
Rtt
AT
=
Vtt
AS
A2
Figure 8-73. ADDR_CTRL Routing for One DDR3 Device
8.13.4.2.4.12 Data Topologies and Routing Definition
No matter the number of DDR3 devices used, the data line topology is always point-to-point, so its
definition is simple.
Care should be taken to minimize layer transitions during routing. If a layer transition is necessary, it is
better to transition to a layer using the same reference plane. If this cannot be accommodated, ensure
there are nearby ground vias to allow the return currents to transition between reference planes if both
reference planes are ground or DVDD_DDR. Ensure there are nearby bypass capacitors to allow the
return currents to transition between reference planes if one of the reference planes is ground. The goal is
to minimize the size of the return current loops.
8.13.4.2.4.12.1 DQS and DQ/DM Topologies, Any Number of Allowed DDR3 Devices
DQS lines are point-to-point differential, and DQ/DM lines are point-to-point singled ended. Figure 8-74
and Figure 8-75 show these topologies.
Processor
DQS
IO Buffer
DQSn+
DQSn-
DDR
DQS
IO Buffer
Routed Differentially
n = 0, 1, 2, 3
Figure 8-74. DQS Topology
Processor
DQ and DM
IO Buffer
Dn
DDR
DQ and DM
IO Buffer
n = 0, 1, 2, 3
Figure 8-75. DQ/DM Topology
8.13.4.2.4.12.2 DQS and DQ/DM Routing, Any Number of Allowed DDR3 Devices
Figure 8-76 and Figure 8-77 show the DQS and DQ/DM routing.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
319
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
DQSn+
DQSn-
DQS
Routed Differentially
n = 0, 1, 2, 3
Figure 8-76. DQS Routing With Any Number of Allowed DDR3 Devices
Dn
DQ and DM
n = 0, 1, 2, 3
Figure 8-77. DQ/DM Routing With Any Number of Allowed DDR3 Devices
8.13.4.2.4.13 Routing Specification
8.13.4.2.4.13.1 CK and ADDR_CTRL Routing Specification
Skew within the CK and ADDR_CTRL net classes directly reduces setup and hold margin and, thus, this
skew must be controlled. The only way to practically match lengths on a PCB is to lengthen the shorter
traces up to the length of the longest net in the net class and its associated clock. A metric to establish
this maximum length is Manhattan distance. The Manhattan distance between two points on a PCB is the
length between the points when connecting them only with horizontal or vertical segments. A reasonable
trace route length is to within a percentage of its Manhattan distance. CACLM is defined as Clock Address
Control Longest Manhattan distance.
Given the clock and address pin locations on the processor and the DDR3 memories, the maximum
possible Manhattan distance can be determined given the placement. Figure 8-78 and Figure 8-79 show
this distance for four loads and two loads, respectively. It is from this distance that the specifications on
the lengths of the transmission lines for the address bus are determined. CACLM is determined similarly
for other address bus configurations; i.e., it is based on the longest net of the CK/ADDR_CTRL net class.
For CK and ADDR_CTRL routing, these specifications are contained in Table 8-75.
320
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
(A)
A1
A8
CACLMY
CACLMX
A8
(A)
A8
(A)
A8
(A)
A8
(A)
Rtt
A3
=
A.
A3
A4
AT
Vtt
AS
A2
It is very likely that the longest CK/ADDR_CTRL Manhattan distance will be for Address Input 8 (A8) on the DDR3
memories. CACLM is based on the longest Manhattan distance due to the device placement. Verify the net class that
satisfies this criteria and use as the baseline for CK/ADDR_CTRL skew matching and length control.
The length of shorter CK/ADDR_CTRL stubs as well as the length of the terminator stub are not included in this
length calculation. Non-included lengths are grayed out in the figure.
Assuming A8 is the longest, CALM = CACLMY + CACLMX + 300 mils.
The extra 300 mils allows for routing down lower than the DDR3 memories and returning up to reach A8.
Figure 8-78. CACLM for Four Address Loads on One Side of PCB
(A)
A1
A8
CACLMY
CACLMX
A8
(A)
A8
(A)
Rtt
A3
=
A.
AT
Vtt
AS
A2
It is very likely that the longest CK/ADDR_CTRL Manhattan distance will be for Address Input 8 (A8) on the DDR3
memories. CACLM is based on the longest Manhattan distance due to the device placement. Verify the net class that
satisfies this criteria and use as the baseline for CK/ADDR_CTRL skew matching and length control.
The length of shorter CK/ADDR_CTRL stubs as well as the length of the terminator stub are not included in this
length calculation. Non-included lengths are grayed out in the figure.
Assuming A8 is the longest, CALM = CACLMY + CACLMX + 300 mils.
The extra 300 mils allows for routing down lower than the DDR3 memories and returning up to reach A8.
Figure 8-79. CACLM for Two Address Loads on One Side of PCB
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
321
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-75. CK and ADDR_CTRL Routing Specification (1) (2)
NO.
PARAMETER
MAX
UNIT
2500
mils
25
mils
660
mils
4
A3 skew
(3)
25
mils
5
A3 skew (4)
125
mils
6
A4 length
660
mils
7
A4 skew
25
mils
8
AS length
100
mils
9
AS skew
100
mils
10
AS+/AS- length
70
mils
11
AS+/AS- skew
5
mils
12
AT length (5)
500
mils
13
AT skew (6)
100
mils
14
AT skew
(7)
15
CK/ADDR_CTRL nominal trace length (8)
16
Center-to-center CK to other DDR3 trace spacing (9)
4w
17
Center-to-center ADDR_CTRL to other DDR3 trace spacing (9) (10)
4w
18
Center-to-center ADDR_CTRL to other ADDR_CTRL trace spacing (9)
3w
19
CK center-to-center spacing (11)
20
CK spacing to other net (9)
21
Rcp (13)
Zo-1
Zo
Zo+
Ω
22
Rtt (13) (14)
Zo-5
Zo
Zo+5
Ω
1
A1+A2 length
2
A1+A2 skew
3
A3 length
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
MIN
CACLM-50
TYP
CACLM
5
mils
CACLM+50
mils
(12)
4w
The use of vias should be minimized.
Additional bypass capacitors are required when using the DDR_1V5 plane as the reference plane to allow the return current to jump
between the DDR_1V5 plane and the ground plane when the net class switches layers at a via.
Non-mirrored configuration (all DDR3 memories on same side of PCB).
Mirrored configuration (one DDR3 device on top of the board and one DDR3 device on the bottom).
While this length can be increased for convenience, its length should be minimized.
ADDR_CTRL net class only (not CK net class). Minimizing this skew is recommended, but not required.
CK net class only.
CACLM is the longest Manhattan distance of the CK and ADDR_CTRL net classes + 300 mils. For definition, see
Section 8.13.4.2.4.13.1, Figure 8-78, and Figure 8-79.
Center-to-center spacing is allowed to fall to minimum (w) for up to 1250 mils of routed length.
The ADDR_CTRL net class of the other DDR EMIF is considered other DDR3 trace spacing.
CK spacing set to ensure proper differential impedance.
The most important thing to do is control the impedance so inadvertent impedance mismatches are not created. Generally speaking,
center-to-center spacing should be either 2w or slightly larger than 2w to achieve a differential impedance equal to twice the singleended impedance, Zo.
Source termination (series resistor at driver) is specifically not allowed.
Termination values should be uniform across the net class.
8.13.4.2.4.13.2 DQS and DQ Routing Specification
Skew within the DQS and DQ/DM net classes directly reduces setup and hold margin and thus this skew
must be controlled. The only way to practically match lengths on a PCB is to lengthen the shorter traces
up to the length of the longest net in the net class and its associated clock. As with CK and ADDR_CTRL,
a reasonable trace route length is to within a percentage of its Manhattan distance. DQLMn is defined as
DQ Longest Manhattan distance n, where n is the byte number. For a 32-bit interface, there are four
DQLMs, DQLM0–DQLM3. Likewise, for a 16-bit interface, there are two DQLMs, DQLM0–DQLM1.
NOTE
It is not required, nor is it recommended, to match the lengths across all bytes. Length
matching is only required within each byte.
322
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Given the DQS and DQ/DM pin locations on the processor and the DDR3 memories, the maximum
possible Manhattan distance can be determined given the placement. Figure 8-80 shows this distance for
four loads. It is from this distance that the specifications on the lengths of the transmission lines for the
data bus are determined. For DQS and DQ/DM routing, these specifications are contained in Table 8-76.
DQLMX0
DB0
DB1
DQ[0:7]/DM0/DQS0
DQ[8:15]/DM1/DQS1
DQLMX1
DQ[16:23]/DM2/DQS2
DB2
DQLMY0
DQLMX2
DQLMY3
DQLMY2
DB3
DQLMY1
DQ[23:31]/DM3/DQS3
DQLMX3
3
2
1
0
DB0 - DB3 represent data bytes 0 - 3.
There are four DQLMs, one for each byte (32-bit interface). Each DQLM is the longest Manhattan distance of the
byte; therefore:
DQLM0 = DQLMX0 + DQLMY0
DQLM1 = DQLMX1 + DQLMY1
DQLM2 = DQLMX2 + DQLMY2
DQLM3 = DQLMX3 + DQLMY3
Figure 8-80. DQLM for Any Number of Allowed DDR3 Devices
Table 8-76. Data Routing Specification (1)
NO.
MAX
UNIT
1
DB0 nominal length (2) (3)
DQLM0
mils
2
DB1 nominal length (2) (4)
DQLM1
mils
3
DB2 nominal length
(2) (5)
DQLM2
mils
4
DB3 nominal length (2) (6)
DQLM3
mils
5
DBn skew (7)
25
mils
6
DQSn+ to DQSn- skew
5
mils
7
DQSn to DBn skew (7) (8)
25
mils
8
Center-to-center DBn to other DDR3 trace spacing (9) (10)
4w
9
Center-to-center DBn to other DBn trace spacing (9) (11)
3w
10
11
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
PARAMETER
DQSn center-to-center spacing
MIN
(12)
DQSn center-to-center spacing to other net
TYP
(13)
(9)
4w
External termination disallowed. Data termination should use built-in ODT functionality.
DQLMn is the longest Manhattan distance of a byte. For definition, see Section 8.13.4.2.4.13.2 and Figure 8-80.
DQLM0 is the longest Manhattan length for the net classes of Byte 0.
DQLM1 is the longest Manhattan length for the net classes of Byte 1.
DQLM2 is the longest Manhattan length for the net classes of Byte 2.
DQLM3 is the longest Manhattan length for the net classes of Byte 3.
Length matching is only done within a byte. Length matching across bytes is neither required nor recommended.
Each DQS pair is length matched to its associated byte.
Center-to-center spacing is allowed to fall to minimum (w) for up to 1250 mils of routed length.
Other DDR3 trace spacing means other DDR3 net classes not within the byte.
This applies to spacing within the net classes of a byte.
DQS pair spacing is set to ensure proper differential impedance.
The most important thing to do is control the impedance so inadvertent impedance mismatches are not created. Generally speaking,
center-to-center spacing should be either 2w or slightly larger than 2w to achieve a differential impedance equal to twice the singleended impedance, Zo.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
323
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.14 Multichannel Audio Serial Port (McASP)
The multichannel audio serial port (McASP) functions as a general-purpose audio serial port optimized for
the needs of multichannel audio applications. The McASP is useful for time-division multiplexed (TDM)
stream, Inter-Integrated Sound (I2S) protocols, and inter-component digital audio interface transmission
(DIT).
8.14.1 McASP Device-Specific Information
The device includes six multichannel audio serial port (McASP) interface peripherals (McASP0, McASP1,
McASP2, McASP3, McASP4, and McASP5). The McASP module consists of a transmit and receive
section. On McASP0/1, these sections can operate completely independently with different data formats,
separate master clocks, bit clocks, and frame syncs or, alternatively, the transmit and receive sections
may be synchronized. On McASP2, McASP3, McASP4, and McASP5, the transmit and receive sections
must always be synchronized. The McASP module also includes shift registers that may be configured to
operate as either transmit data or receive data.
The transmit section of the McASP can transmit data in either a time-division-multiplexed (TDM)
synchronous serial format or in a digital audio interface (DIT) format where the bit stream is encoded for
S/PDIF, AES-3, IEC-60958, CP-430 transmission. The receive section of the McASP peripheral supports
the TDM synchronous serial format.
The McASP module can support one transmit data format (either a TDM format or DIT format) and one
receive format at a time. All transmit shift registers use the same format and all receive shift registers use
the same format; however, the transmit and receive formats need not be the same. Both the transmit and
receive sections of the McASP also support burst mode, which is useful for non-audio data (for example,
passing control information between two devices).
The McASP peripheral has additional capability for flexible clock generation and error detection/handling,
as well as error management.
The device McASP0 and McASP1 modules have up to 10 serial data pins, while McASP2, McASP3,
McASP4, and McASP5 are limited to up to four serial data pins each. The McASP FIFO size is 256 bytes
and two DMA and two interrupt requests are supported. Buffers are used transparently to better manage
DMA, which can be leveraged to manage data flow more efficiently.
For more detailed information on and the functionality of the McASP peripheral, see the Multichannel
Audio Serial Port (McASP) chapter of the TMS320DM814x DaVinci Digital Media Processors Technical
Reference Manual (Literature Number: SPRUGZ8).
8.14.2 McASP0, McASP1, McASP2, McASP3, McASP4, and McASP5 Peripheral Registers
Descriptions
Table 8-77. McASP0/1/2/3/4/5 Registers
HEX ADDRESS RANGE
MCASP3
MCASP4
ACRONYM
MCASP1
MCASP2
0x4803 8000
0x4803 C000
0x4805 0000
0x4A1A 2000 0x4A1A 8000 0x4A1A E000
PID
Peripheral ID
0x4803 8010
0x4803 C010
0x4805 0010
0x4A1A 2010 0x4A1A 8010 0x4A1A E010
PFUNC
Pin Function
0x4803 8014
0x4803 C014
0x4805 0014
0x4A1A 2014 0x4A1A 8014 0x4A1A E014
PDIR
Pin Direction
0x4803 8018
0x4803 C018
0x4805 0018
0x4A1A 2018 0x4A1A 8018 0x4A1A E018
PDOUT
Pin Data Out
0x4803 801C 0x4803 C01C 0x4805 001C 0x4A1A 201C 0x4A1A 801C
MCASP5
REGISTER NAME
MCASP0
0x4A1A
E01C
PDIN
PDSET
324
Peripheral Information and Timings
Pin Data Input (Read)
Read returns pin data input
Pin Data Set (Write)
Writes effect pin data set
(Alternate Write Address
PDOUT)
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-77. McASP0/1/2/3/4/5 Registers (continued)
HEX ADDRESS RANGE
MCASP3
MCASP4
REGISTER NAME
MCASP1
MCASP2
0x4803 8020
0x4803 C020
0x4805 0020
0x4A1A 2020 0x4A1A 8020 0x4A1A E020
PDCLR
Pin Data Clear
(Alternate Write Address
PDOUT)
0x4803 8044
0x4803 C044
0x4805 0044
0x4A1A 2044 0x4A1A 8044 0x4A1A E044
GBLCTL
Global Control
0x4803 8048
0x4803 C048
0x4805 0048
0x4A1A 2048 0x4A1A 8048 0x4A1A E048
AMUTE
Mute Control
LBCTL
Loop-Back Test Control
0x4803 804C 0x4803 C04C 0x4805 004C 0x4A1A 204C 0x4A1A 804C
MCASP5
ACRONYM
MCASP0
0x4A1A
E04C
0x4803 8050
0x4803 C050
0x4805 0050
0x4A1A 2050 0x4A1A 8050 0x4A1A E050
TXDITCTL
Transmit DIT Mode Control
0x4803 8060
0x4803 C060
0x4805 0060
0x4A1A 2060 0x4A1A 8060 0x4A1A E060
GBLCTLR
Alias of GBLCTL containing
only receiver reset bits;
allows transmit to be reset
independently from receive
0x4803 8064
0x4803 C064
0x4805 0064
0x4A1A 2064 0x4A1A 8064 0x4A1A E064
RXMASK
Receiver Bit Mask
0x4803 8068
0x4803 C068
0x4805 0068
0x4A1A 2068 0x4A1A 8068 0x4A1A E068
RXFMT
0x4803 806C 0x4803 C06C 0x4805 006C 0x4A1A 206C 0x4A1A 806C
0x4A1A
E06C
Receive Bitstream Format
RXFMCTL
Receive Frame Sync Control
ACLKRCTL
Receive Clock Control
0x4803 8070
0x4803 C070
0x4805 0070
0x4A1A 2070 0x4A1A 8070 0x4A1A E070
0x4803 8074
0x4803 C074
0x4805 0074
0x4A1A 2074 0x4A1A 8074 0x4A1A E074 AHCLKRCTL High Frequency Receive
Clock Control
0x4803 8078
0x4803 C078
0x4805 0078
0x4A1A 2078 0x4A1A 8078 0x4A1A E078
0x4803 807C 0x4803 C07C 0x4805 007C 0x4A1A 207C 0x4A1A 807C
0x4A1A
E07C
RXTDM
EVTCTLR
Receiver Interrupt Control
0x4803 8080
0x4803 C080
0x4805 0080
0x4A1A 2080 0x4A1A 8080 0x4A1A E080
0x4803 8084
0x4803 C084
0x4805 0084
0x4A1A 2084 0x4A1A 8084 0x4A1A E084 RXTDMSLOT Current Receive TDM Slot
0x4803 8088
0x4803 C088
0x4805 0088
0x4A1A 2088 0x4A1A 8088 0x4A1A E088
0x4803 808C 0x4803 C08C 0x4805 008C 0x4A1A 208C 0x4A1A 808C
0x4A1A
E08C
RXSTAT
Receive TDM Slot 0-31
RXCLKCHK
Status Receiver
Receiver Clock Check
Control
REVTCTL
Receiver DMA Event Control
0x4803 80A0 0x4803 C0A0
0x4805 00A0 0x4A1A 20A0 0x4A1A 80A0 0x4A1A E0A0
GBLCTLX
Alias of GBLCTL containing
only transmit reset bits;
allows transmit to be reset
independently from receive
0x4803 80A4 0x4803 C0A4
0x4805 00A4 0x4A1A 20A4 0x4A1A 80A4 0x4A1A E0A4
TXMASK
Transmit Format Unit Bit
Mask
0x4803 80A8 0x4803 C0A8
0x4805 00A8 0x4A1A 20A8 0x4A1A 80A8 0x4A1A E0A8
TXFMT
0x4803 80AC 0x4803 C0AC 0x4805 00AC
0x4A1A
20AC
0x4A1A
80AC
0x4A1A
E0AC
Transmit Bitstream Format
TXFMCTL
Transmit Frame Sync Control
ACLKXCTL
Transmit Clock Control
0x4803 80B0 0x4803 C0B0
0x4805 00B0 0x4A1A 20B0 0x4A1A 80B0 0x4A1A E0B0
0x4803 80B4 0x4803 C0B4
0x4805 00B4 0x4A1A 20B4 0x4A1A 80B4 0x4A1A E0B4 AHCLKXCTL High Frequency Transmit
Clock Control
0x4803 80B8 0x4803 C0B8
0x4805 00B8 0x4A1A 20B8 0x4A1A 80B8 0x4A1A E0B8
0x4803 80BC 0x4803 C0BC 0x4805 00BC
EVTCTLX
0x4803 80C0 0x4803 C0C0 0x4805 00C0 0x4A1A 20C0 0x4A1A 80C0
0x4A1A
E0C0
TXSTAT
0x4803 80C4 0x4803 C0C4 0x4805 00C4 0x4A1A 20C4 0x4A1A 80C4
0x4A1A
E0C4
0x4803 80C8 0x4803 C0C8 0x4805 00C8 0x4A1A 20C8 0x4A1A 80C8
0x4A1A
E0C8
TXCLKCHK
0x4803 80CC
0x4A1A
E0CC
XEVTCTL
0x4A1A
E0D0
CLKADJEN
0x4805 00CC
0x4A1A
20CC
0x4A1A
80BC
TXTDM
0x4A1A
E0BC
0x4803
C0CC
0x4A1A
20BC
0x4A1A
80CC
0x4803 80D0 0x4803 C0D0 0x4805 00D0 0x4A1A 20D0 0x4A1A 80D0
Transmit TDM Slot 0-31
Transmitter Interrupt Control
Status Transmitter
TXTDMSLOT Current Transmit TDM Slot
Transmit Clock Check
Control
Transmitter DMA Control
One-shot Clock Adjust
Enable
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
325
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-77. McASP0/1/2/3/4/5 Registers (continued)
HEX ADDRESS RANGE
MCASP0
MCASP1
MCASP2
MCASP3
MCASP4
0x4803 8100
0x4803 C100
0x4805 0100
0x4A1A 2100 0x4A1A 8100
0x4803 8104
0x4803 C104
0x4805 0104
0x4A1A 2104 0x4A1A 8104
0x4803 8108
0x4803 C108
0x4805 0108
0x4A1A 2108 0x4A1A 8108
0x4803 810C 0x4803 C10C 0x4805 010C 0x4A1A 210C 0x4A1A 810C
0x4803 8110
0x4803 C110
0x4805 0110
0x4A1A 2110 0x4A1A 8110
0x4803 8114
0x4803 C114
0x4805 0114
0x4A1A 2114 0x4A1A 8114
0x4803 8118
0x4803 C118
0x4805 0118
0x4A1A 2118 0x4A1A 8118
0x4803 811C 0x4803 C11C 0x4805 011C 0x4A1A 211C 0x4A1A 811C
0x4803 8120
0x4803 C120
0x4805 0120
0x4A1A 2120 0x4A1A 8120
0x4803 8124
0x4803 C124
0x4805 0124
0x4A1A 2124 0x4A1A 8124
0x4803 8128
0x4803 C128
0x4805 0128
0x4A1A 2128 0x4A1A 8128
0x4803 812C 0x4803 C12C 0x4805 012C 0x4A1A 212C 0x4A1A 812C
0x4803 8130
0x4803 C130
0x4805 0130
0x4A1A 2130 0x4A1A 8130
0x4803 8134
0x4803 C134
0x4805 0134
0x4A1A 2134 0x4A1A 8134
0x4803 8138
0x4803 C138
0x4805 0138
0x4A1A 2138 0x4A1A 8138
0x4803 813C 0x4803 C13C 0x4805 013C 0x4A1A 213C 0x4A1A 813C
0x4803 8140
0x4803 C140
0x4805 0140
0x4A1A 2140 0x4A1A 8140
0x4803 8144
0x4803 C144
0x4805 0144
0x4A1A 2144 0x4A1A 8144
0x4803 8148
0x4803 C148
0x4805 0148
0x4A1A 2148 0x4A1A 8148
0x4803 814C 0x4803 C14C 0x4805 014C 0x4A1A 214C 0x4A1A 814C
0x4803 8150
0x4803 C150
0x4805 0150
0x4A1A 2150 0x4A1A 8150
0x4803 8154
0x4803 C154
0x4805 0154
0x4A1A 2154 0x4A1A 8154
0x4803 8158
0x4803 C158
0x4805 0158
0x4A1A 2158 0x4A1A 8158
0x4803 815C 0x4803 C15C 0x4805 015C 0x4A1A 215C 0x4A1A 815C
ACRONYM
REGISTER NAME
0x4A1A E100
DITCSRA0
Left (Even TDM Slot)
Channel Status Register File
0x4A1A E104
DITCSRA1
Left (Even TDM Slot)
Channel Status Register File
0x4A1A E108
DITCSRA2
Left (Even TDM Slot)
Channel Status Register File
0x4A1A
E10C
DITCSRA3
Left (Even TDM Slot)
Channel Status Register File
0x4A1A E110
DITCSRA4
Left (Even TDM Slot)
Channel Status Register File
0x4A1A E114
DITCSRA5
Left (Even TDM Slot)
Channel Status Register File
0x4A1A E118
DITCSRB0
Right (Odd TDM Slot)
Channel Status Register File
0x4A1A
E11C
DITCSRB1
Right (Odd TDM Slot)
Channel Status Register File
0x4A1A E120
DITCSRB2
Right (Odd TDM Slot)
Channel Status Register File
0x4A1A E124
DITCSRB3
Right (Odd TDM Slot)
Channel Status Register File
0x4A1A E128
DITCSRB4
Right (Odd TDM Slot)
Channel Status Register File
0x4A1A
E12C
DITCSRB5
Right (Odd TDM Slot)
Channel Status Register File
0x4A1A E130
DITUDRA0
Left (Even TDM Slot) User
Data Register File
0x4A1A E134
DITUDRA1
Left (Even TDM Slot) User
Data Register File
0x4A1A E138
DITUDRA2
Left (Even TDM Slot) User
Data Register File
0x4A1A
E13C
DITUDRA3
Left (Even TDM Slot) User
Data Register File
0x4A1A E140
DITUDRA4
Left (Even TDM Slot) User
Data Register File
0x4A1A E144
DITUDRA5
Left (Even TDM Slot) User
Data Register File
0x4A1A E148
DITUDRB0
Right (Odd TDM Slot) User
Data Register File
0x4A1A
E14C
DITUDRB1
Right (Odd TDM Slot) User
Data Register File
0x4A1A E150
DITUDRB2
Right (Odd TDM Slot) User
Data Register File
0x4A1A E154
DITUDRB3
Right (Odd TDM Slot) User
Data Register File
0x4A1A E158
DITUDRB4
Right (Odd TDM Slot) User
Data Register File
0x4A1A
E15C
DITUDRB5
Right (Odd TDM Slot) User
Data Register File
MCASP5
0x4803 8180 0x4803 C180 0x4805 0180 0x4A1A 2180 0x4A1A 8180 0x4A1A E180
0x4803 81BC 0x4803 C1BC 0x4805 01BC
0x4A1A
0x4A1A
0x4A1A
21BC
81BC
E1BC
0x4803 8200
0x4803 8
23C
326
0x4803 C200 0x4805 0200 0x4A1A 2200 0x4A1A 8200 0x4A1A E200
0x4803 C23C 0x4805 023C 0x4A1A 223C 0x4A1A 823C
0x4A1A
E23C
Peripheral Information and Timings
XRSRCTL0 - Serializer 0 Control XRSRCTL15 Serializer 15 Control
TXBUF0 TXBUF15
Transmit Buffer for Serializer
0 - Transmit Buffer for
Serializer 15
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-77. McASP0/1/2/3/4/5 Registers (continued)
HEX ADDRESS RANGE
MCASP0
MCASP1
MCASP2
MCASP3
MCASP4
MCASP5
0x4803 8280 0x4803 C280 0x4805 0280 0x4A1A 2280 0x4A1A 8280 0x4A1A E280
0x4803 82BC 0x4803 C2BC 0x4805 02BC
0x4A1A
0x4A1A
0x4A1A
22BC
82BC
E2BC
ACRONYM
RXBUF0 RXBUF15
REGISTER NAME
Receive Buffer for Serializer
0 - Receive Buffer for
Serializer 15
0x4803 9000
0x4803 D000
0x4805 1000
0x4A1A 3000 0x4A1A 9000 0x4A1A F000
BUFFER_CF Write FIFO Control
GRD_WFIFO
CTL
0x4803 9004
0x4803 D004
0x4805 1004
0x4A1A 3004 0x4A1A 9004 0x4A1A F004
BUFFER_CF Write FIFO Status
GRD_WFIFO
STS
0x4803 9008
0x4803 D008
0x4805 1008
0x4A1A 3008 0x4A1A 9008 0x4A1A F008
BUFFER_CF Read FIFO Control
GRD_RFIFO
CTL
0x4803 900C 0x4803 D00C 0x4805 100C 0x0A1A 300C 0x0A1A 900C 0x0A1A F00C BUFFER_CF Read FIFO Status
GRD_RFIFO
STS
0x4803 9010 0x4803 D010 0x4805 1010 0x4A1A 3010 0x4A1A 9010 0x4A1A F010
0x4803 9FFF 0x4803 DFFF 0x4805 1FFF 0x4A1A 3FFF 0x4A1A 9FFF 0x4A1A FFFF
–
Reserved
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
327
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.14.3 McASP (McASP[5:0]) Electrical Data/Timing
Table 8-78. Timing Requirements for McASP (1)
(see Figure 8-81)
OPP100/120/166
NO.
McASP[5:2,0] Only
MIN
1
tc(AHCLKRX)
Cycle time, MCA[x]_AHCLKR/X
2
tw(AHCLKRX)
Pulse duration, MCA[x]_AHCLKR/X high or low
Any Other
Conditions
3
tc(ACLKRX)
Cycle time, MCA[x]_ACLKR/X
ACLKx, AFSX
and AXR are all
inputs
Any Other
Conditions
4
tw(ACLKRX)
Pulse duration, MCA[x]_ACLKR/X high
ACLKx, AFSX
or low
and AXR are all
inputs
ACLKR/X int
5
tsu(AFSRXACLKRX)
Setup time, MCA[x]_AFSR/X input
valid before MCA[X]_ACLKR/X
th(ACLKRXAFSRX)
Hold time, MCA[x]_AFSR/X input valid
after MCA[X]_ACLKR/X
tsu(AXR-ACLKRX)
Setup time, MCA[x]_AXR input valid
before MCA[X]_ACLKR/X
(1)
(2)
(3)
328
th(ACLKRX-AXR)
Hold time, MCA[x]_AXR input valid
after MCA[X]_ACLKR/X
UNIT
MAX
20
20
ns
0.5P - 3 (2)
0.5P - 3 (2)
ns
20
20
ns
–
12.5
ns
0.5R - 3 (3)
0.5R - 3 (3)
ns
–
0.5R 1.5 (3)
ns
10.5
4
2
ACLKR/X ext out
4
2
-1
-1
ACLKR/X ext in
1
2
ACLKR/X ext out
1
2
10.5
10.5
ACLKR/X ext in
4
2
ACLKR/X ext out
4
2
ACLKR/X int
8
MIN
10.5
ACLKR/X int
7
McASP1 Only
ACLKR/X ext in
ACLKR/X int
6
MAX
-1
-1
ACLKR/X ext in
1
2
ACLKR/X ext out
1
2
ns
ns
ns
ns
ACLKR internal: ACLKRCTL.CLKRM=1, PDIR.ACLKR = 1
ACLKR external input: ACLKRCTL.CLKRM=0, PDIR.ACLKR=0
ACLKR external output: ACLKRCTL.CLKRM=0, PDIR.ACLKR=1
ACLKX internal: ACLKXCTL.CLKXM=1, PDIR.ACLKX = 1
ACLKX external input: ACLKXCTL.CLKXM=0, PDIR.ACLKX=0
ACLKX external output: ACLKXCTL.CLKXM=0, PDIR.ACLKX=1
P = MCA[x]_AHCLKR/X period in nano seconds (ns).
R = MCA[x]_ACLKR/X period in ns.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
2
1
2
MCA[x]_ACLKR/X (Falling Edge Polarity)
MCA[x]_AHCLKR/X (Rising Edge Polarity)
4
4
3
MCA[x]_ACLKR/X (CLKRP = CLKXP = 0)
MCA[x]_ACLKR/X (CLKRP = CLKXP = 1)
(A)
(B)
6
5
MCA[x]_AFSR/X (Bit Width, 0 Bit Delay)
MCA[x]_AFSR/X (Bit Width, 1 Bit Delay)
MCA[x]_AFSR/X (Bit Width, 2 Bit Delay)
MCA[x]_AFSR/X (Slot Width, 0 Bit Delay)
MCA[x]_AFSR/X (Slot Width, 1 Bit Delay)
MCA[x]_AFSR/X (Slot Width, 2 Bit Delay)
8
7
MCA[x]_AXR[x] (Data In/Receive)
A.
B.
For CLKRP = CLKXP =
receiver is configured for
For CLKRP = CLKXP =
receiver is configured for
A0 A1
A30 A31 B0 B1
B30 B31 C0 C1 C2 C3
0, the McASP transmitter is configured for rising edge (to shift data out) and the McASP
falling edge (to shift data in).
1, the McASP transmitter is configured for falling edge (to shift data out) and the McASP
rising edge (to shift data in).
C31
Figure 8-81. McASP Input Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
329
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-79. Switching Characteristics Over Recommended Operating Conditions for McASP (1)
(see Figure 8-82)
NO.
9
tc(AHCLKRX)
tw(AHCLKRX)
Pulse duration, MCA[X]_AHCLKR/X high or low
11
tc(ACLKRX)
Cycle time, MCA[X]_ACLKR/X
12
tw(ACLKRX)
Pulse duration, MCA[X]_ACLKR/X high or low
td(ACLKRX-AFSRX)
Delay time, MCA[X]_ACLKR/X transmit edge to
MCA[X]_AFSR/X output valid
Delay time, MCA[X]_ACLKR/X transmit edge to
MCA[X]_AFSR/X output valid with Pad Loopback
14
td(ACLKX-AXR)
Delay time, MCA[X]_ACLKX transmit edge to
MCA[X]_AXR output valid
Delay time, MCA[X]_ACLKX transmit edge to
MCA[X]_AXR output valid with Pad Loopback
Disable time, MCA[X]_ACLKX transmit edge to
MCA[X]_AXR output high impedance
15
(1)
(2)
(3)
330
tdis(ACLKX-AXR)
MIN
Cycle time, MCA[X]_AHCLKR/X
10
13
OPP100/120/166
PARAMETER
Disable time, MCA[X]_ACLKX transmit edge to
MCA[X]_AXR output high impedance with Pad
Loopback
ACLKR/X int
MAX
20 (2)
ns
0.5P 2.5 (3)
ns
20
ns
0.5P 2.5 (3)
ns
-2
5
ACLKR/X ext in
1
11.5
ACLKR/X ext out
1
11.5
-2
5
ACLKX ext in
1
11.5
ACLKX ext out
1
11.5
ACLKX int
ACLKX int
UNIT
-2
5
ACLKX ext in
1
11.5
ACLKX ext out
1
11.5
ns
ns
ns
ACLKR internal: ACLKRCTL.CLKRM=1, PDIR.ACLKR = 1
ACLKR external input: ACLKRCTL.CLKRM=0, PDIR.ACLKR=0
ACLKR external output: ACLKRCTL.CLKRM=0, PDIR.ACLKR=1
ACLKX internal: ACLKXCTL.CLKXM=1, PDIR.ACLKX = 1
ACLKX external input: ACLKXCTL.CLKXM=0, PDIR.ACLKX=0
ACLKX external output: ACLKXCTL.CLKXM=0, PDIR.ACLKX=1
50 MHz
P = AHCLKR/X period.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
10
10
9
MCA[x]_ACLKR/X (Falling Edge Polarity)
MCA[x]_AHCLKR/X (Rising Edge Polarity)
11
MCA[x]_ACLKR/X (CLKRP = CLKXP = 1)
MCA[x]_ACLKR/X (CLKRP = CLKXP = 0)
12
12
(A)
(B)
13
13
13
13
MCA[x]_AFSR/X (Bit Width, 0 Bit Delay)
MCA[x]_AFSR/X (Bit Width, 1 Bit Delay)
MCA[x]_AFSR/X (Bit Width, 2 Bit Delay)
MCA[x]_AFSR/X (Slot Width, 0 Bit Delay)
13
13
13
MCA[x]_AFSR/X (Slot Width, 1 Bit Delay)
MCA[x]_AFSR/X (Slot Width, 2 Bit Delay)
MCA[x]_AXR[x] (Data Out/Transmit)
14
15
A.
B.
For CLKRP = CLKXP =
receiver is configured for
For CLKRP = CLKXP =
receiver is configured for
A0 A1
A30 A31 B0 B1
B30 B31 C0 C1 C2 C3
C31
1, the McASP transmitter is configured for falling edge (to shift data out) and the McASP
rising edge (to shift data in).
0, the McASP transmitter is configured for rising edge (to shift data out) and the McASP
falling edge (to shift data in).
Figure 8-82. McASP Output Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
331
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.15 Multichannel Buffered Serial Port (McBSP)
The McBSP provides these functions:
• Full-duplex communication
• Double-buffered data registers, which allow a continuous data stream
• Independent framing and clocking for receive and transmit
• Direct interface to industry-standard codecs, analog interface chips (AICs), and other serially
connected analog-to-digital (A/D) and digital-to-analog (D/A) devices
• Supports TDM, I2S, and similar formats
• External shift clock or an internal, programmable frequency shift clock for data transfer
• 5KB Tx and Rx buffer
• Supports three interrupt and two DMA requests.
The McBSP module may support two types of data transfer at the system level:
• The full-cycle mode, for which one clock period is used to transfer the data, generated on one edge
and captured on the same edge (one clock period later).
• The half-cycle mode, for which one half clock period is used to transfer the data, generated on one
edge and captured on the opposite edge (one half clock period later). Note that a new data is
generated only every clock period, which secures the required hold time. The interface clock
(CLKX/CLKR) activation edge (data/frame sync capture and generation) has to be configured
accordingly with the external peripheral (activation edge capability) and the type of data transfer
required at the system level.
For more detailed information on the McBSP peripheral, see the Multichannel Buffered Serial Port
(McBSP) chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual
(Literature Number: SPRUGZ8).
The following sections describe the timing characteristics for applications in normal mode (that is, the
McBSP connected to one peripheral) and TDM applications in multipoint mode.
8.15.1 McBSP Peripheral Register Descriptions
Table 8-80. McBSP Registers (1)
(1)
332
HEX ADDRESS
ACRONYM
0x4700 0000
REVNB
0x4700 0010
SYSCONFIG_REG
0x4700 0020
EOI
0x4700 0024
IRQSTATUS_RAW
REGISTER NAME
Revision Number Register
System Configuration Register
End of Interrupt Register
Interrupt Status Raw Register
0x4700 0028
IRQSTATUS
0x4700 002C
IRQENABLE_SET
Interrupt Status Register
Interrupt Enable Set Register
0x4700 0030
IRQENABLE_CLR
Interrupt Enable Clear Register
0x4700 0034
DMARXENABLE_SET
DMA Rx Enable Set Register
0x4700 0038
DMATXENABLE_SET
DMA Tx Enable Set Register
0x4700 003C
DMARXENABLE_CLR
DMA Rx Enable Clear Register
0x4700 0040
DMATXENABLE_CLR
DMA Tx Enable Clear Register
0x4700 0048
DMARXWAKE_EN
DMA Rx Wake Enable Register
0x4700 004C
DMATXWAKE_EN
DMA Tx Wake Enable Register
0x4700 0100
DRR_REG
McBSP data receive
0x4700 0108
DXR_REG
McBSP data transmit
0x4700 0110
SPCR2_REG
McBSP serial port control 2
0x4700 0114
SPCR1_REG
McBSP serial port control 1
Note that the McBSP registers are 32-bit aligned.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-80. McBSP Registers(1) (continued)
HEX ADDRESS
ACRONYM
REGISTER NAME
0x4700 0118
RCR2_REG
McBSP receive control 2
0x4700 011C
RCR1_REG
McBSP receive control 1
0x4700 0120
XCR2_REG
McBSP transmit control 2
0x4700 0124
XCR1_REG
McBSP transmit control 1
0x4700 0128
SRGR2_REG
McBSP sample rate generator 2
0x4700 012C
SRGR1_REG
McBSP sample rate generator 1
0x4700 0130
MCR2_REG
McBSP multichannel 2
0x4700 0134
MCR1_REG
McBSP multichannel 1
0x4700 0138
RCERA_REG
McBSP receive channel enable partition A
0x4700 013C
RCERB_REG
McBSP receive channel enable partition B
0x4700 0140
XCERA_REG
McBSP transmit channel enable partition A
0x4700 0144
XCERB_REG
McBSP transmit channel enable partition B
0x4700 0148
PCR_REG
0x4700 014C
RCERC_REG
McBSP receive channel enable partition C
0x4700 0150
RCERD_REG
McBSP receive channel enable partition D
0x4700 0154
XCERC_REG
McBSP transmit channel enable partition C
0x4700 0158
XCERD_REG
McBSP transmit channel enable partition D
0x4700 015C
RCERE_REG
McBSP receive channel enable partition E
0x4700 0160
RCERF_REG
McBSP receive channel enable partition F
0x4700 0164
XCERE_REG
McBSP transmit channel enable partition E
0x4700 0168
XCERF_REG
McBSP transmit channel enable partition F
0x4700 016C
RCERG_REG
McBSP receive channel enable partition G
0x4700 0170
RCERH_REG
McBSP receive channel enable partition H
0x4700 0174
XCERG_REG
McBSP transmit channel enable partition G
McBSP transmit channel enable partition H
McBSP pin control
0x4700 0178
XCERH_REG
0x4700 017C
REV_REG
0x4700 0180
RINTCLR_REG
McBSP receive interrupt clear
0x4700 0184
XINTCLR_REG
McBSP transmit interrupt clear
0x4700 0188
ROVFLCLR_REG
McBSP receive overflow interrupt clear
0x4700 018C
SYSCONFIG_REG
McBSP system configuration
0x4700 0190
THRSH2_REG
McBSP transmit buffer threshold (DMA or IRQ trigger)
McBSP revision number
0x4700 0194
THRSH1_REG
McBSP receive buffer threshold (DMA or IRQ trigger)
0x4700 01A0
IRQSTATATUS
McBSP interrupt status (OCP compliant IRQ line)
0x4700 01A4
IRQENABLE
McBSP interrupt enable (OCP compliant IRQ line)
0x4700 01A8
WAKEUPEN
McBSP wakeup enable
0x4700 01AC
XCCR_REG
McBSP transmit configuration control
0x4700 01B0
RCCR_REG
McBSP receive configuration control
0x4700 01B4
XBUFFSTAT_REG
McBSP transmit buffer status
0x4700 01B8
RBUFFSTAT_REG
McBSP receive buffer status
0x4700 01C0
STATUS_REG
McBSP status
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
333
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.15.2 McBSP Electrical Data/Timing
Table 8-81. Timing Requirements for McBSP - Master Mode (1)
(see Figure 8-83)
OPP100/120/166
NO.
6
tsu(DRV-CLKAE)
7
(1)
MIN
th(CLKAE-DRV)
Setup time, MCB_DR valid before MCB_CLK active edge (2)
Hold time, MCB_DR valid after MCB_CLK active edge
(2)
MAX
UNIT
3.5
ns
3.5
ns
The timings apply to all configurations regardless of MCB_CLK polarity and which clock edges are used to drive output data and capture
input data.
MCB_CLK corresponds to either MCB_CLKX or MCB_CLKR.
(2)
Table 8-82. Switching Characteristics Over Recommended Operating Conditions for McBSP - Master
Mode (1)
(see Figure 8-83)
NO.
1
OPP100/120/166
PARAMETER
tc(CLK)
MIN
Cycle time, output MCB_CLK period (2)
(2)
MAX
UNIT
20.83
ns
(3)
ns
0.5*P - 1 (3)
ns
2
tw(CLKL)
Pulse duration, output MCB_CLK low
3
tw(CLKH)
Pulse duration, output MCB_CLK high (2)
4
td(CLKAE-FSV)
Delay time, output MCB_CLK active edge to output MCB_FS
valid (2) (4)
0.3
9.4
ns
5
td(CLKXAE-DXV)
Delay time, output MCB_CLKX active edge to output MCB_DX
valid
0.3
9.4
ns
(1)
(2)
(3)
(4)
334
0.5*P - 1
The timings apply to all configurations regardless of MCB_CLK polarity and which clock edges are used to drive output data and capture
input data.
MCB_CLK corresponds to either MCB_CLKX or MCB_CLKR.
P = MCB_CLKX/MCB_CLKR output CLK period, in ns; use whichever value is greater. This parameter applies to the maximum McBSP
frequency. Operate serial clocks (CLKX/R) in the reasonable range of 40/60 duty cycle.
MCB_FS corresponds to either MCB_FSX or MCB_FSR.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
2
1
3
MCB_CLK
4
4
MCB_FS
5
5
MCB_DX
MCB_DX7
5
MCB_DX6
MCB_DX0
MCB_DR6
MCB_DR0
7
6
MCB_DR
A.
B.
C.
D.
E.
F.
MCB_DR7
The timings apply to all configurations regardless of MCB_CLK polarity and which clock edges are used to drive
output data and capture input data.
MCBSP_CLK corresponds to either MCBSP_CLKX or MCBSP_CLKR; MCBSP_FS corresponds to either
MCBSP_FSX
or
MCBSP_FSR.
McBSP in 6-pin mode: DX and DR as data pins; CLKX, CLKR, FSX and FSR as control pins.
McBSP in 4-pin mode: DX and DR as data pins; CLKX and FSX pins as control pins. The CLKX and FSX pins are
internally looped back via software configuration, respectively to the CLKR and FSR internal signals for data receive.
The polarity of McBSP frame synchronization is software configurable.
The active clock edge selection of MCBSP_CLK (rising or falling) on which MCBSP_DX data is latched and
MCBSP_DR data is sampled is software configurable.
Timing diagrams are for data delay set to 1.
For further details about the registers used to configure McBSP, see the Multichannel Buffered Serial Port (McBSP)
chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
Figure 8-83. McBSP Master Mode Timing
Table 8-83. Timing Requirements for McBSP - Slave Mode (1)
(see Figure 8-84)
OPP100/120/166
NO.
MIN
MAX
UNIT
1
tc(CLK)
Cycle time, MCB_CLK period (2)
20.83
ns
2
tw(CLKL)
Pulse duration, MCB_CLK low (2)
0.5*P - 1 (3)
ns
3
tw(CLKH)
Pulse duration, MCB_CLK high (2)
0.5*P - 1 (3)
ns
(2) (4)
4
tsu(FSV-CLKAE)
Setup time, MCB_FS valid before MCB_CLK active edge
3.8
ns
5
th(CLKAE-FSV)
Hold time, MCB_FS valid after MCB_CLK active edge (2) (4)
0.5
ns
7
tsu(DRV-CLKAE)
Setup time, MCB_DR valid before MCB_CLK active edge (2)
3.8
ns
8
th(CLKAE-DRV)
Hold time, MCB_DR valid after MCB_CLK active edge (2)
0.5
ns
(1)
The timings apply to all configurations regardless of MCB_CLK polarity and which clock edges are used to drive output data and capture
input data.
MCB_CLK corresponds to either MCB_CLKX or MCB_CLKR.
P = MCB_CLKX/MCB_CLKR output CLK period, in ns; use whichever value is greater. This parameter applies to the maximum McBSP
frequency. Operate serial clocks (CLKX/R) in the reasonable range of 40/60 duty cycle.
MCB_FS corresponds to either MCB_FSX or MCB_FSR.
(2)
(3)
(4)
Table 8-84. Switching Characteristics Over Recommended Operating Conditions for McBSP - Slave
Mode (1)
(see Figure 8-84)
NO.
6
(1)
PARAMETER
td(CLKXAE-DXV)
Delay time, input MCB_CLKx active edge to output MCB_DX valid
OPP100/120/166
MIN
MAX
0.5
12.5
UNIT
ns
The timings apply to all configurations regardless of MCB_CLK polarity and which clock edges are used to drive output data and capture
input data.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
335
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
2
1
3
MCB_CLK
4
5
MCB_FS
6
MCB_DX
6
MCB_DX7
6
MCB_DX6
MCB_DX0
MCB_DR6
MCB_DR0
8
7
MCB_DR
A.
B.
C.
D.
E.
F.
MCB_DR7
The timings apply to all configurations regardless of MCB_CLK polarity and which clock edges are used to drive
output data and capture input data.
MCBSP_CLK corresponds to either MCBSP_CLKX or MCBSP_CLKR; MCBSP_FS corresponds to either
MCBSP_FSX
or
MCBSP_FSR.
McBSP in 6-pin mode: DX and DR as data pins; CLKX, CLKR, FSX and FSR as control pins.
McBSP in 4-pin mode: DX and DR as data pins; CLKX and FSX pins as control pins. The CLKX and FSX pins are
internally looped back via software configuration, respectively to the CLKR and FSR internal signals for data receive.
The polarity of McBSP frame synchronization is software configurable.
The active clock edge selection of MCBSP_CLK (rising or falling) on which MCBSP_DX data is latched and
MCBSP_DR data is sampled is software configurable.
Timing diagrams are for data delay set to 1.
For further details about the registers used to configure McBSP, see the Multichannel Buffered Serial Port (McBSP)
chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
Figure 8-84. McBSP Slave Mode Timing
336
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.16 MultiMedia Card/Secure Digital/Secure Digital Input Output (MMC/SD/SDIO)
The device includes 3 MMC/SD/SDIO Controllers which are compliant with MMC V4.3, Secure Digital Part
1 Physical Layer Specification V2.00 and Secure Digital Input Output (SDIO) V2.00 specifications.
The device MMC/SD/SDIO Controller has the following features:
• MultiMedia card (MMC)
• Secure Digital (SD) memory card
• MMC/SD protocol support
• SDIO protocol support
• Programmable clock frequency
• 1024 byte read/write FIFO to lower system overhead
• Slave EDMA transfer capability
• SD High capacity support
8.16.1 MMC/SD/SDIO Peripheral Register Descriptions
Table 8-85. MMC/SD/SDIO Registers (1)
(1)
MMC/SD/SDIO0
HEX ADDRESS
MMC/SD/SDIO1
HEX ADDRESS
MMC/SD/SDIO2
HEX ADDRESS
ACRONYM
REGISTER NAME
0x4806 0000
0x481D 8000
0x4781 0000
MMCHS_HL_REV
0x4806 0004
0x481D 8004
0x4781 0004
MMCHS_HL_HWINF Hardware Configuration
O
0x4806 0010
0x481D 8010
0x4781 0010
MMCHS_HL_SYSCO Clock Management Configuration
NFIG
0x4806 0110
0x481D 8110
0x4781 0110
MMCHS_SYSCONFI System Configuration
G
0x4806 0114
0x481D 8114
0x4781 0114
MMCHS_SYSSTATU System Status
S
0x4806 0124
0x481D 8124
0x4781 0124
MMCHS_CSRE
0x4806 0128
0x481D 8128
0x4781 0128
MMCHS_SYSTEST
System Test
0x4806 012C
0x481D 812C
0x4781 012C
MMCHS_CON
Configuration
0x4806 0130
0x481D 8130
0x4781 0130
MMCHS_PWCNT
Power counter
0x4806 0200
0x481D 8200
0x4781 0200
MMCHS_SDMASA
SDMA System address:
0x4806 0204
0x481D 8204
0x4781 0204
MMCHS_BLK
Transfer Length Configuration
IP Revision Identifier
Card status response error
0x4806 0208
0x481D 8208
0x4781 0208
MMCHS_ARG
Command argument
0x4806 020C
0x481D 820C
0x4781 020C
MMCHS_CMD
Command and transfer mode
0x4806 0210
0x481D 8210
0x4781 0210
MMCHS_RSP10
Command Response 0 and 1
0x4806 0214
0x481D 8214
0x4781 0214
MMCHS_RSP32
Command Response 2 and 3
0x4806 0218
0x481D 8218
0x4781 0218
MMCHS_RSP54
Command Response 4 and 5
0x4806 021C
0x481D 821C
0x4781 021C
MMCHS_RSP76
Command Response 6 and 7
0x4806 0220
0x481D 8220
0x4781 0220
MMCHS_DATA
Data
0x4806 0224
0x481D 8224
0x4781 0224
MMCHS_PSTATE
Present state
0x4806 0228
0x481D 8228
0x4781 0228
MMCHS_HCTL
Host Control
0x4806 022C
0x481D 822C
0x4781 022C
MMCHS_SYSCTL
0x4806 0230
0x481D 8230
0x4781 0230
MMCHS_STAT
0x4806 0234
0x481D 8234
0x4781 0234
MMCHS_IE
0x4806 0238
0x481D 8238
0x4781 0238
MMCHS_ISE
0x4806 023C
0x481D 823C
0x4781 023C
MMCHS_AC12
Auto CMD12 Error Status
0x4806 0240
0x481D 8240
0x4781 0240
MMCHS_CAPA
Capabilities
0x4806 0248
0x481D 8248
0x4781 0248
SD system control
Interrupt status
Interrupt SD enable
Interrupt Signal Enable
MMCHS_CUR_CAPA Maximum current capabilities
SD/SDIO registers are limited to 32-bit data accesses; 16-bit and 8-bit accesses are not allowed and can corrupt register content.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
337
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-85. MMC/SD/SDIO Registers(1) (continued)
MMC/SD/SDIO0
HEX ADDRESS
MMC/SD/SDIO1
HEX ADDRESS
MMC/SD/SDIO2
HEX ADDRESS
ACRONYM
REGISTER NAME
0x4806 0250
0x481D 8250
0x4806 0254
0x481D 8254
0x4781 0250
MMCHS_FE
Force Event
0x4781 0254
MMCHS_ADMAES
0x4806 0258
0x481D 8258
ADMA Error Status
0x4781 0258
MMCHS_ADMASAL
ADMA System address Low bits
ADMA System address High bits
0x4806 025C
0x481D 825C
0x4781 025C
MMCHS_ADMASAH
0x4806 02FC
0x481D 82FC
0x4781 02FC
MMCHS_REV
Versions
8.16.2 MMC/SD/SDIO Electrical Data/Timing
Table 8-86. Timing Requirements for MMC/SD/SDIO
(see Figure 8-86, Figure 8-88)
OPP100/120/166
NO
.
ALL MODES
MIN
1
tsu(CMDV-CLKH)
Setup time, SD_CMD valid before SD_CLK rising clock edge
th(CLKH-CMDV)
Hold time, SD_CMD valid after SD_CLK rising clock edge
3
tsu(DATV-CLKH)
Setup time, SD_DATx valid before SD_CLK rising clock edge
th(CLKH-DATV)
Hold time, SD_DATx valid after SD_CLK rising clock edge
MAX
4.1
2
4
UNIT
SD1
1.9
SD0, SD2
2.9
ns
ns
4.1
SD1
1.9
SD0, SD2
2.9
ns
ns
Table 8-87. Switching Characteristics Over Recommended Operating Conditions for MMC/SD/SDIO
(see Figure 8-85 through Figure 8-88)
OPP100/120/166
MODES
NO.
PARAMETER
3.3 V STD
1.8 V SDR12
MIN
7
8
9
fop(CLK)
Operating frequency, SD_CLK
tc(CLK)
Operating period: SD_CLK
fop(CLKID)
Identification mode frequency, SD_CLK
tc(CLKID)
Identification mode period: SD_CLK
tw(CLKL)
Pulse duration, SD_CLK low
UNIT
3.3 V HS
1.8 V SDR25
MAX
MIN
24
41.7
MAX
48
20.8
400
MHz
ns
400
kHz
2500.0
2500.0
ns
0.5*P (1)
0.5*P (1)
ns
(1)
(1)
10
tw(CLKH)
Pulse duration, SD_CLK high
11
tr(CLK)
Rise time, All Signals (10% to 90%)
2.2
2.2
ns
12
tf(CLK)
Fall time, All Signals (10% to 90%)
2.2
2.2
ns
13
td(CLKL-CMD)
Delay time, SD_CLK rising clock edge to SD_CMD
transition
1.5
10
1.5
10
ns
14
td(CLKL-DAT)
Delay time, SD_CLK rising clock edge to SD_DATx
transition
1.5
10
1.5
10
ns
(1)
0.5*P
0.5*P
ns
P = SD_CLK period.
10
7
9
SDx_CLK
13
SDx_CMD
13
START
13
13
XMIT
Valid
Valid
Valid
END
Figure 8-85. MMC/SD/SDIO Host Command Timing
338
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
9
7
10
SDx_CLK
1
2
SDx_CMD
START
XMIT
Valid
Valid
Valid
END
Figure 8-86. MMC/SD/SDIO Card Response Timing
10
9
7
SDx_CLK
14
14
START
SDx_DAT[x]
14
14
D0
D1
Dx
END
Figure 8-87. MMC/SD/SDIO Host Write Timing
9
10
7
SDx_CLK
4
4
3
3
SDx_DAT[x]
Start
D0
D1
Dx
End
Figure 8-88. MMC/SD/SDIO Host Read and Card CRC Status Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
339
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.17 Peripheral Component Interconnect Express (PCIe)
The device supports connections to PCIe-compliant devices via the integrated PCIe master/slave bus
interface. The PCIe module is comprised of a dual-mode PCIe core and a SerDes PHY. The device
implements a single one-lane PCIe 2.0 (5.0 GT/s) Endpoint/Root Complex port.
The device PCIe supports the following features:
• Supports Gen1/Gen2 in x1 or x2 mode
• One port with one 5 GT/s lane
• Single virtual channel (VC), single traffic class (TC)
• Single function in end-point mode
• Automatic width and speed negotiation and lane reversal
• Max payload: 128 byte outbound, 256 byte inbound
• Automatic credit management
• ECRC generation and checking
• Configurable BAR filtering
• Supports PCIe messages
• Legacy interrupt reception (RC) and generation (EP)
• MSI generation and reception
• PCI device power management, except D3 cold with vaux
• Active state power management state L0 and L1.
For more detailed information on the PCIe port peripheral module, see the PCI Express (PCIe) Module
chapter of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature
Number: SPRUGZ8).
The PCIe peripheral on the device conforms to the PCI Express Base 2.0 Specification.
8.17.1 PCIe Peripheral Register Descriptions
Table 8-88. PCIe Registers
340
HEX ADDRESS
ACRONYM
0x5100 0000
PID
REGISTER NAME
0x5100 0004
CMD_STATUS
0x5100 0008
CFG_SETUP
0x5100 000C
IOBASE
IO TLP Base
0x5100 0010
TLPCFG
TLP Attribute Configuration
0x5100 0014
RSTCMD
Reset Command and Status
0x5100 0020
PMCMD
Power Management Command
0x5100 0024
PMCFG
Power Management Configuration
0x5100 0028
ACT_STATUS
Activity Status
0x5100 0030
OB_SIZE
Outbound Size
0x5100 0034
DIAG_CTRL
Peripheral Version and ID
Command Status
Config Transaction Setup
Diagnostic Control
0x5100 0038
ENDIAN
0x5100 003C
PRIORITY
Endian Mode
0x5100 0050
IRQ_EOI
End of Interrupt
0x5100 0054
MSI_IRQ
MSI Interrupt IRQ
CBA Transaction Priority
0x5100 0064
EP_IRQ_SET
Endpoint Interrupt Request Set
0x5100 0068
EP_IRQ_CLR
Endpoint Interrupt Request Clear
0x5100 006C
EP_IRQ_STATUS
0x5100 0070
GPRO
Peripheral Information and Timings
Endpoint Interrupt Status
General Purpose 0
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-88. PCIe Registers (continued)
HEX ADDRESS
ACRONYM
REGISTER NAME
0x5100 0074
GPR1
General Purpose 1
0x5100 0078
GPR2
General Purpose 2
0x5100 007C
GPR3
General Purpose 3
0x5100 0100
MSI0_IRQ_STATUS_RAW
MSI 0 Interrupt Raw Status
0x5100 0104
MSI0_IRQ_STATUS
0x5100 0108
MSI0_IRQ_ENABLE_SET
MSI 0 Interrupt Enabled Status
MSI 0 Interrupt Enable Set
0x5100 010C
MSI0_IRQ_ENABLE_CLR
MSI 0 Interrupt Enable Clear
0x5100 0180
IRQ_STATUS_RAW
0x5100 0184
IRQ_STATUS
0x5100 0188
IRQ_ENABLE_SET
Interrupt Enable Set
0x5100 018C
IRQ_ENABLE_CLR
Interrupt Enable Clear
0x5100 01C0
ERR_IRQ_STATUS_RAW
0x5100 01C4
ERR_IRQ_STATUS
0x5100 01C8
ERR_IRQ_ENABLE_SET
ERR Interrupt Enable Set
0x5100 01CC
ERR_IRQ_ENABLE_CLR
ERR Interrupt Enable Clear
0x5100 01D0
PMRST_IRQ_STATUS_RAW
0x5100 01D4
PMRST_IRQ_STATUS
Power Management and Reset Interrupt Enabled Status
Raw Interrupt Status
Interrupt Enabled Status
Raw ERR Interrupt Status
ERR Interrupt Enabled Status
Power Management and Reset Interrupt Status
0x5100 01D8
PMRST_ENABLE_SET
Power Management and Reset Interrupt Enable Set
0x5100 01DC
PMRST_ENABLE_CLR
Power Management and Reset Interrupt Enable Clear
0x5100 0200
OB_OFFSET_INDEXn
Outbound Translation Region N Offset Low and Index
0x5100 0204
OB_OFFSETn_HI
Outbound Translation Region N Offset High
0x5100 0300
IB_BAR0
0x5100 0304
IB_START0_LO
Inbound Translation Bar Match 0
Inbound Translation 0 Start Address Low
0x5100 0308
IB_START0_HI
Inbound Translation 0 Start Address High
0x5100 030C
IB_OFFSET0
0x5100 0310
IB_BAR1
0x5100 0314
IB_START1_LO
Inbound Translation 1 Start Address Low
Inbound Translation 1 Start Address High
Inbound Translation 0 Address Offset
Inbound Translation Bar Match 1
0x5100 0318
IB_START1_HI
0x5100 031C
IB_OFFSET1
0x5100 0320
IB_BAR2
0x5100 0324
IB_START2_LO
Inbound Translation 2 Start Address Low
Inbound Translation 2 Start Address High
Inbound Translation 1 Address Offset
Inbound Translation Bar Match 2
0x5100 0328
IB_START2_HI
0x5100 032C
IB_OFFSET2
0x5100 0330
IB_BAR3
0x5100 0334
IB_START3_LO
Inbound Translation 3 Start Address Low
0x5100 0338
IB_START3_HI
Inbound Translation 3 Start Address High
0x5100 033C
IB_OFFSET3
0x5100 0380
PCS_CFG0
PCS Configuration 0
0x5100 0384
PCS_CFG1
PCS Configuration 1
0x5100 0388
PCS_STATUS
0x5100 038C
SERDES_STATUS
SerDes Status
0x5100 0390
SERDES_RXCFG0
SerDes Receive Configuration 0 Register
0x5100 0394
SERDES_RXCFG1
SerDes Receive Configuration 1 Register
0x5100 0398
SERDES_RXCFG2
SerDes Receive Configuration 2 Register
0x5100 039C
SERDES_RXCFG3
SerDes Receive Configuration 3 Register
0x5100 03A0
SERDES_RXCFG4
SerDes Receive Configuration 4 Register
0x5100 03A4
SERDES_TXCFG0
SerDes Transmit Configuration 0 Register
Inbound Translation 2 Address Offset
Inbound Translation Bar Match 3
Inbound Translation 3 Address Offset
PCS Status
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
341
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-88. PCIe Registers (continued)
HEX ADDRESS
ACRONYM
0x5100 03A8
SERDES_TXCFG1
REGISTER NAME
SerDes Transmit Configuration 1 Register
0x5100 03AC
SERDES_TXCFG2
SerDes Transmit Configuration 2 Register
0x5100 03B0
SERDES_TXCFG3
SerDes Transmit Configuration 3 Register
0x5100 03B4
SERDES_TXCFG4
SerDes Transmit Configuration 4 Register
Table 8-89. Configuration Registers Type 0 Summary
HEX ADDRESS
ACRONYM
NAME
5100_1000
VENDOR_DEVICE Vendor Device ID Register
_ID
5100_1004
STATUS_COMMA Status and Command
ND
Register
5100_1008
CLASSCODE_RE
VID
5100_100C
BIST_HEADER
5100_1010
BAR0 (64/-32-Bit
Mode)
Base Address Register 0
5100_1014
BAR1 (32-Bit
Mode)
Base Address Register 1
BAR1 (64-Bit
Mode)
Base Address Register 1 (64bit BAR0)
Class Code and Revision
Register
BIST, Header Type, Latency
Time, and Cache Line Size
register
5100_1018
BAR2 (64/-32-Bit
Mode)
Base Address Register 2
5100_101C
BAR3 (32-Bit
Mode)
Base Address Register 3
BAR3 (64-Bit
Mode)
Base Address Register 3 (64bit BAR2)
5100_1020
BAR4 (64/-32-Bit
Mode)
Base Address Register 4
5100_1024
BAR5 (32-Bit
Mode)
Base Address Register 5
BAR5 (64-Bit
Mode)
Base Address Register 5 (64bit BAR4)
5100_1028
CARDBUS
5100_102C
CardBus CIS Pointer
Register
SUBSYS_VNDR_I Subsystem and Subsystem
D
Vendor ID Register
5100_1030
EXPNSN_ROM
5100_1034
CAP_PTR
5100_103C
INT_PIN
Expansion ROM Base
Address Register
Capabilities Pointer Register
Interrupt Pin Register
Table 8-90. Configuration Registers Type 1 Summary
342
HEX ADDRESS
ACRONYM
5100_1000
VENDOR_DEVICE_ID
Vendor Device ID Register
5100_1004
STATUS_COMMAND
Status and Command Register
Class Code and Revision Register
5100_1008
CLASSCODE_REVID
5100_100C
BIST_HEADER
5100_1010
BAR0 (64/-32-Bit Mode)
Peripheral Information and Timings
NAME
BIST, Header Type, Latency Time, and Cache Line Size
register
Base Address Register 0 (64/32-bit mode)
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-90. Configuration Registers Type 1 Summary (continued)
HEX ADDRESS
ACRONYM
5100_1014
BAR1 (32-Bit Mode)
Base Address Register 1 (32-bit mode)
NAME
BAR1 (64-Bit Mode)
Base Address Register 1 (64-bit BAR0)
5100_1018
BUSNUM
Latency Timer and Bus Number Register
5100_101C
SECSTAT
Secondary Status and I/O Base/Limit Register
5100_1020
MEMSPACE
5100_1024
PREFETCH_MEM
Memory Limit and Base Register
Prefetchable Memory Limit and Base Register
5100_1028
PREFETCH_BASE
Prefetchable Memory Base Upper 32-bits Register
5100_102C
PREFETCH_LIMIT
Prefetchable Limit Upper 32-bits Register
5100_1030
IOSPACE
I/O Base and Limit Upper 16-bits Register
5100_1034
CAP_PTR
Capabilities Pointer Register
5100_1038
EXPNSN_ROM
5100_103C
BRIDGE_INT
Expansion ROM Base Address Register
Bridge Control Register
Table 8-91. Power Management Capability Register Summary
HEX ADDRESS
ACRONYM
5100_1040
PMCAP
5100_1044
PM_CTL_STAT
NAME
Power Management Capability Register
Power Management Control and Status Register
Table 8-92. Message Signaled Interrupts (MSI) Register Summary
HEX ADDRESS
ACRONYM
5100_1050
MSI_CAP
NAME
5100_1054
MSI_LOW32
MSI Lower 32 bits Register
5100_1058
MSI_UP32
MSI Upper 32 bits Register
5100_105C
MSI_DATA
MSI Data Register
MSI Capabilities Register
Table 8-93. PCI Express Capabilities Register Summary
HEX ADDRESS
ACRONYM
NAME
5100_1070
PCIES_CAP
5100_1074
DEVICE_CAP
PCI Express Capabilities Register
5100_1078
DEV_STAT_CTRL
5100_107C
LINK_CAP
5100_1080
LINK_STAT_CTRL
5100_1084
SLOT_CAP
5100_1088
SLOT_STAT_CTRL
Slot Status and Control Register (RC Mode Only)
5100_108C
ROOT_CTRL_CAP
Root Control and Capabilities Register (RC Mode Only)
5100_1090
ROOT_STATUS
5100_1094
DEV_CAP2
5100_1098
DEV_STAT_CTRL2
5100_10A0
LINK_CTRL2
Device Capabilities Register
Device Status and Control Register
Link Capabilities Register
Link Status and Control Register
Slot Capabilities Register (RC Mode Only)
Root Status and Control Register (RC Mode Only)
Device Capabilities 2 Register
Device Status and Control 2 Register
Link Control 2 Register
Table 8-94. PCI Express Extended Capabilities Register Summary
HEX ADDRESS
ACRONYM
5100_1100
PCIE_EXTCAP
PCI Express Extended Capabilities Header Register
NAME
5100_1104
PCIE_UNCERR
PCI Express Uncorrectable Error Status Register
5100_1108
PCIE_UNCERR_MASK
PCI Express Uncorrectable Error Mask Register
5100_110C
PCIE_UNCERR_SVRTY
PCI Express Uncorrectable Error Severity Register
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
343
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-94. PCI Express Extended Capabilities Register Summary (continued)
HEX ADDRESS
ACRONYM
5100_1110
PCIE_CERR
PCI Express Correctable Error Status Register
NAME
5100_1114
PCIE_CERR_MASK
PCI Express Correctable Error Mask Register
5100_1118
PCIE_ACCR
PCI Express Advanced Capabilities and Control Register
5100_111C
HDR_LOG0
Header Log 0 Register
5100_1120
HDR_LOG1
Header Log 1 Register
5100_1124
HDR_LOG2
Header Log 2 Register
5100_1128
HDR_LOG3
Header Log 3 Register
5100_112C
RC_ERR_CMD
5100_1130
RC_ERR_ST
Root Error Status Register
5100_1134
ERR_SRC_ID
Error Source Identification Register
Root Error Command Register
Table 8-95. Port Logic Register Summary
HEX ADDRESS
ACRONYM
5100_1700
PL_ACKTIMER
NAME
Ack Latency Time and Replay Timer Register
5100_1704
PL_OMSG
Other Message Register
5100_1708
PL_FORCE_LINK
Port Force Link Register
5100_170C
ACK_FREQ
Ack Frequency Register
5100_1710
PL_LINK_CTRL
5100_1714
LANE_SKEW
5100_1718
SYM_NUM
5100_171C
SYMTIMER_FLTMASK
5100_1720
FLT_MASK2
5100_1728
DEBUG0
Debug 0 Register
5100_172C
DEBUG1
Debug 1 Register
5100_180C
PL_GEN2
Gen2 Register
Port Link Control Register
Lane Skew Register
Symbol Number Register
Symbol Timer and Filter Mask Register
Filter Mask 2 Register
8.17.2 PCIe Electrical Data/Timing
Texas Instruments (TI) has performed the simulation and system characterization to ensure that the PCIe
peripheral meets all AC timing specifications as required by the PCI Express Base 2.0 Specification.
Therefore, the AC timing specifications are not reproduced here. For more information on the AC timing
specifications, see Sections 4.3.3.5 and 4.3.4.4 of the PCI Express Base 2.0 Specification.
8.17.3 PCIe Design and Layout Guidelines
8.17.3.1 Clock Source
A standard 100-MHz PCIe differential clock source must be used for PCIe operation (for more details, see
Section 7.4.2, SERDES CLKN/P Input Clock).
8.17.3.2 PCIe Connections and Interface Compliance
The PCIe interface on the device is compliant with the PCI Express Base 2.0 Specification. Refer to the
PCIe specifications for all connections that are described in it. For coupling capacitor selection, see
Section 8.17.3.2.1, Coupling Capacitors.
The use of PCIe-compatible bridges and switches is allowed for interfacing with more than one other
processor or PCIe device.
344
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.17.3.2.1 Coupling Capacitors
AC coupling capacitors are required on the transmit data pair. Table 8-96 shows the requirements for
these capacitors.
Table 8-96. AC Coupling Capacitors Requirements
PARAMETER
PCIe AC coupling capacitor value
MIN
PCIe AC coupling capacitor package size (1)
(1)
(2)
TYP
75
0402
MAX
UNIT
200
nF
0603
EIA (2)
The physical size of the capacitor should be as small as practical. Use the same size on both lines in each pair, placed side by side.
EIA LxW units; that is, a 0402 is a 40x20 mil (thousandths of an inch) surface-mount capacitor.
8.17.3.2.2 Polarity Inversion
The PCIe specification requires polarity inversion support. This means, for layout purposes, polarity is
unimportant since each signal can change its polarity on-die inside the chip. This means polarity within a
lane is unimportant for layout.
8.17.3.3 Non-Standard PCIe Connections
The following sections contain suggestions for any PCIe connection that is not described in the official
PCIe specification, such as an on-board device-to-device connection, or device-to-other PCIe-compliant
processor connection.
8.17.3.3.1 PCB Stackup Specifications
Table 8-97 shows the stackup and feature sizes required for these types of PCIe connections.
Table 8-97. PCIe PCB Stackup Specifications
MIN
TYP
MAX
PCB Routing/Plane Layers
PARAMETER
4
6
-
Layers
Signal Routing Layers
2
3
-
Layers
Number of ground plane cuts allowed within PCIe routing region
-
-
0
Cuts
Number of layers between PCIe routing area and reference plane (1)
-
-
0
Layers
PCB Routing clearance
-
4
-
Mils
PCB Trace width (2)
-
4
-
Mils
PCB BGA escape via pad size
-
20
-
Mils
PCB BGA escape via hole size
-
10
Mils
0.4
mm
Processor BGA pad size
(1)
(2)
(3)
(4)
(3) (4)
UNIT
A reference plane may be a ground plane or the power plane referencing the PCIe signals.
In breakout area.
Non-solder mask defined pad.
Per IPC-7351A BGA pad size guideline.
8.17.3.3.2 Routing Specifications
The PCIe data signal traces must be routed to achieve 100 Ω (±20%) differential impedance and 60 Ω
(±15%) single-ended impedance. The single-ended impedance is required because differential signals are
extremely difficult to closely couple on PCBs and, therefore, single-ended impedance becomes important.
These requirements are the same as those recommended in the PCIe Motherboard Checklist 1.0
document, available from PCI-SIG.
These impedances are impacted by trace width, trace spacing, distance between signals and referencing
planes, and dielectric material. Verify with a PCB design tool that the trace geometry for both data signal
pairs result in as close to 100 Ω differential impedance and 60 Ω single-ended impedance as possible. For
best accuracy, work with your PCB fabricator to ensure this impedance is met.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
345
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
In general, closely coupled differential signal traces are not an advantage on PCBs. When differential
signals are closely coupled, tight spacing and width control is necessary. Very small width and spacing
variations affect impedance dramatically, so tight impedance control can be more problematic to maintain
in production.
Loosely coupled PCB differential signals make impedance control much easier. Wider traces and spacing
make obstacle avoidance easier, and trace width variations do not affect impedance as much; therefore, it
is easier to maintain an accurate impedance over the length of the signal. The wider traces also show
reduced skin effect and, therefore, often result in better signal integrity.
Table 8-98 shows the routing specifications for the PCIe data signals.
Table 8-98. PCIe Routing Specifications
MAX
UNIT
PCIe signal trace length
PARAMETER
MIN
TYP
10 (1)
Inches
Differential pair trace matching
10 (2)
Number of stubs allowed on PCIe traces (3)
0
TX/RX pair differential impedance
80
100
120
TX/RX single ended impedance
51
60
69
Mils
Stubs
Ω
Ω
Pad size of vias on PCIe trace
25 (4)
Hole size of vias on PCIe trace
14
Mils
3
Vias (5)
Number of vias on each PCIe trace
PCIe differential pair to any other trace spacing
(1)
(2)
(3)
(4)
(5)
(6)
346
Mils
2*DS (6)
Beyond this, signal integrity may suffer.
For example, RXP0 within 10 Mils of RXN0.
In-line pads may be used for probing.
35-Mil antipad max recommended.
Vias must be used in pairs with their distance minimized.
DS = differential spacing of the PCIe traces.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.18 Serial ATA Controller (SATA)
The Serial ATA (SATA) peripheral provides a direct interface to one hard disk drive (SATA 300) or up to
15 hard disk drives using a Port Multiplier and supports the following features:
• Serial ATA 1.5 Gbps and 3 Gbps speeds
• Integrated PHY
• Integrated Rx and Tx data buffers
• Supports all SATA power management features
• Hardware-assisted native command queuing (NCQ) for up to 32 entries
• Supports port multiplier with command-based switching
• Activity LED support.
8.18.1 SATA Peripheral Register Descriptions
Table 8-99. SATA Registers
HEX ADDRESS
ACRONYM
REGISTER NAME
0x4A14 0000
CAP
HBA Capabilities
0x4A14 0004
GHC
Global HBA Control
0x4A14 0008
IS
Interrupt Status
0x4A14 000C
PI
Ports Implemented
0x4A14 0010
VS
AHCI Version
0x4A14 0014
CCC_CTL
0x4A14 0018
CCC_PORTS
Command Completion Coalescing Control
Command Completion Coalescing Ports
0x4A14 001C - 0x4A14 009C
-
0x4A14 00A0
BISTAFR
Reserved
BIST Active FIS
0x4A14 00A4
BISTCR
BIST Control
0x4A14 00A8
BISTFCTR
0x4A14 00AC
BISTSR
0x4A14 00B0
BISTDECR
0x4A14 00B4 - 0x4A14 00DF
-
0x4A14 00E0
TIMER1MS
0x4A14 00E4
-
0x4A14 00E8
GPARAM1R
Global Parameter 1
0x4A14 00EC
GPARAM2R
Global Parameter 2
0x4A14 00F0
PPARAMR
0x4A14 00F4
TESTR
0x4A14 00F8
VERSIONR
0x4A14 00FC
IDR (PID)
0x4A14 0100
P0CLB
0x4A14 0104
-
BIST FIS Count
BIST Status
BIST DWORD Error Count
Reserved
BIST DWORD Error Count
Reserved
Port Parameter
Test
Version
ID
Port 0 Command List Base Address
Reserved
0x4A14 0108
P0FB
0x4A14 010C
-
Port 0 FIS Base Address
0x4A14 0110
P0IS
Port 0 Interrupt Status
0x4A14 0114
P0IE
Port 0 Interrupt Enable
0x4A14 0118
P0CMD
0x4A14 011C
-
0x4A14 0120
P0TFD
Port 0 Task File Data
0x4A14 0124
P0SIG
Port 0 Signature
0x4A14 0128
P0SSTS
Reserved
Port 0 Command
Reserved
Port 0 Serial ATA Status (SStatus)
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
347
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-99. SATA Registers (continued)
HEX ADDRESS
ACRONYM
0x4A14 012C
P0SCTL
Port 0 Serial ATA Control (SControl)
0x4A14 0130
P0SERR
Port 0 Serial ATA Error (SError)
0x4A14 0134
P0SACT
Port 0 Serial ATA Active (SActive)
0x4A14 0138
P0CI
0x4A14 013C
P0SNTF
0x4A14 0140 - 0x4A14 016C
-
0x4A14 0170
P0DMACR
REGISTER NAME
Port 0 Command Issue
Port 0 Serial ATA Notification
Reserved
Port 0 DMA Control
0x4A14 0174 - 0x4A14 017C
-
Reserved
0x4A14 0180 - 0x4A14 01FC
-
Reserved
0x4A14 1100
IDLE
0x4A14 1104
CFGRX0
PHY Configuration Receive 0 Register
Idle and Standby Modes
0x4A14 1108
CFGRX1
PHY Configuration Receive 1 Register
0x4A14 110C
CFGRX2
PHY Configuration Receive 2 Register
0x4A14 1110
CFGRX3
PHY Configuration Receive 3 Register
0x4A14 1114
CFGRX4
PHY Configuration Receive 4 Register
0x4A14 1118
STSRX
0x4A14 111C
CFGTX0
PHY Configuration Transmit 0 Register
0x4A14 1120
CFGTX1
PHY Configuration Transmit 1 Register
0x4A14 1124
CFGTX2
PHY Configuration Transmit 2 Register
0x4A14 1128
CFGTX3
PHY Configuration Transmit 3 Register
0x4A14 112C
CFGTX4
PHY Configuration Transmit 4 Register
0x4A14 1130
STSTX
Receive Bus PHY-to-Controller Status Register (Used for
Debug Purposes)
Transmit Bus Controller-to-PHY Status Register (Used for
Debug Purposes)
8.18.2 SATA Interface Design Guidelines
This section provides PCB design and layout guidelines for the SATA interface. The design rules constrain
PCB trace length, PCB trace skew, signal integrity, cross-talk, and signal timing. Simulation and system
design work has been done to ensure the SATA interface requirements are met.
A standard 100-MHz differential clock source must be used for SATA operation (for details, see
Section 7.4.2, SERDES_CLKN/P Input Clock).
8.18.2.1 SATA Interface Schematic
Figure 8-89 shows the data portion of the SATA interface schematic. The specific pin numbers can be
obtained from Table 3-26, Serial ATA Terminal Functions.
SATA Interface (Processor)
SATA Connector
10 nF
SATA_TXN0
SATA_TXP0
TXTX+
10 nF
10 nF
SATA_RXN0
SATA_RXP0
RXRX+
10 nF
Figure 8-89. SATA Interface High-Level Schematic
348
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.18.2.2 Compatible SATA Components and Modes
Table 8-100 shows the compatible SATA components and supported modes. Note that the only supported
configuration is an internal cable from the processor host to the SATA device.
Table 8-100. SATA Supported Modes
PARAMETER
MIN
MAX
UNIT
1.5
3.0
Gbps
xSATA
-
-
-
No
Backplane
-
-
-
No
Internal Cable (iSATA)
-
-
-
Yes
Transfer Rates
SUPPORTED
8.18.2.3 PCB Stackup Specifications
Table 8-101 shows the PCB stackup and feature sizes required for SATA.
Table 8-101. SATA PCB Stackup Specifications
MIN
TYP
MAX
PCB routing/plane layers
PARAMETER
4
6
-
Layers
Signal routing layers
2
3
-
Layers
Number of ground plane cuts allowed within SATA routing region
-
-
0
Cuts
Number of layers between SATA routing region and reference ground plane
-
-
0
Layers
PCB trace width, w
-
4
-
Mils
PCB BGA escape via pad size
-
20
-
Mils
PCB BGA escape via hole size
-
Processor BGA pad size (1)
(1)
UNIT
10
Mils
0.4
mm
NSMD pad, per IPC-7351A BGA pad size guideline.
8.18.2.4 Routing Specifications
The SATA data signal traces must be routed to achieve 100 Ω (±20%) differential impedance and 60 Ω
(±15%) single-ended impedance. The single-ended impedance is required because differential signals are
extremely difficult to closely couple on PCBs and, therefore, single-ended impedance becomes important.
60 Ω is chosen for the single-ended impedance to minimize problems caused by too low an impedance.
These impedances are impacted by trace width, trace spacing, distance to reference planes, and dielectric
material. Verify with a PCB design tool that the trace geometry for both data signal pairs results in as
close to 100 Ω differential impedance and 60 Ω single-ended impedance traces as possible. For best
accuracy, work with your PCB fabricator to ensure this impedance is met.
Table 8-102 shows the routing specifications for the SATA data signals.
Table 8-102. SATA Routing Specifications
PARAMETER
MIN
TYP
Processor-to-SATA header trace length
Number of stubs allowed on SATA traces (2)
MAX
UNIT
10 (1)
Inches
0
Stubs
Ω
TX/RX pair differential impedance
80
100
120
TX/RX single ended impedance
51
60
69
Ω
3
Vias (3)
Number of vias on each SATA trace
SATA differential pair to any other trace spacing
(1)
(2)
(3)
(4)
2*DS (4)
Beyond this, signal integrity may suffer.
In-line pads may be used for probing.
Vias must be used in pairs with their distance minimized.
DS = differential spacing of the SATA traces.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
349
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.18.2.5 Coupling Capacitors
AC coupling capacitors are required on the receive data pair. Table 8-103 shows the requirements for
these capacitors.
Table 8-103. SATA AC Coupling Capacitors Requirements
PARAMETER
MIN
TYP
MAX
1
10
12
0402
0603
SATA AC coupling capacitor value
SATA AC coupling capacitor package size (1)
(1)
(2)
350
UNIT
nF
EIA (2)
The physical size of the capacitor should be as small as practical. Use the same size on both lines in each pair, placed side by side.
EIA LxW units; that is, a 0402 is a 40 x 20 mil surface-mount capacitor.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.19 Serial Peripheral Interface (SPI)
The SPI is a high-speed synchronous serial input/output port that allows a serial bit stream of programmed
length (4 to 32 bits) to be shifted into and out of the device at a programmed bit-transfer rate. The SPI is
normally used for communication between the device and external peripherals. Typical applications
include an interface-to-external I/O or peripheral expansion via devices such as shift registers, display
drivers, SPI EEPROMs, and Analog-to-Digital Converters (ADCs).
The SPI supports the following features:
• Master/Slave operation
• Four chip selects for interfacing/control to up to four SPI Slave devices and connection to a single
external Master
• 32-bit shift register
• Buffered receive/transmit data register per channel (1 word deep), FIFO size is 64 bytes
• Programmable SPI configuration per channel (clock definition, enable polarity and word width)
• Supports one interrupt request and two DMA requests per channel.
For more detailed information on the SPI, see the Multichannel Serial Port Interface (McSPI) chapter of
the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
8.19.1 SPI Peripheral Register Descriptions
Table 8-104. SPI Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
SPI0
SPI1
SPI2
SPI3
0x4803 0000
0x481A 0000
0x481A 2000
0x481A 4000
MCSPI_HL_REV
0x4803 0004
0x481A 0004
0x481A 2004
0x481A 4004
MCSPI_HL_HWIN
FO
0x4803 0008 0x4803 000C
0x481A 0008 0x481A 000C
0x481A 2008 0x481A 200C
0x481A 4008 0x481A 400C
-
0x4803 0010
0x481A 0010
0x481A 2010
0x481A 4010
MCSPI_HL_SYSC
ONFIG
0x4803 0014 0x4803 00FF
0x481A 0014 0x481A 00FF
0x481A 2014 0x481A 20FF
0x481A 4014 0x481A 40FF
-
0x4803 0100
0x481A 0100
0x481A 2100
0x481A 4100
0x4803 0104 0x4803 010C
0x481A 0104 0x481A 010C
0x481A 2104 0x481A 210C
0x481A 4104 0x481A 410C
0x4803 0110
0x481A 0110
0x481A 2110
0x481A 4110
MCSPI_SYSCONF SYSTEM CONFIGURATION
IG
0x4803 0114
0x481A 0114
0x481A 2114
0x481A 4114
MCSPI_SYSSTAT
US
0x4803 0118
0x481A 0118
0x481A 2118
0x481A 4118
MCSPI_IRQSTATU INTERRUPT STATUS
S
0x4803 011C
0x481A 011C
0x481A 211C
0x481A 411C
MCSPI_IRQENABL INTERRUPT ENABLE
E
0x4803 0120
0x481A 0120
0x481A 2120
0x481A 4120
MCSPI_WAKEUPE WAKEUP ENABLE
NABLE
0x4803 0124
0x481A 0124
0x481A 2124
0x481A 4124
0x4803 0128
0x481A 0128
0x481A 2128
0x481A 4128
MCSPI_MODULCT MODULE CONTROL
RL
0x4803 012C
0x481A 012C
0x481A 212C
0x481A 412C
MCSPI_CH0CONF CHANNEL 0 CONFIGURATION
0x4803 0130
0x481A 0130
0x481A 2130
0x481A 4130
MCSPI_CH0STAT
0x4803 0134
0x481A 0134
0x481A 2134
0x481A 4134
MCSPI_CH0CTRL CHANNEL 0 CONTROL
0x4803 0138
0x481A 0138
0x481A 2138
0x481A 4138
SPI REVISION
SPI HARDWARE
INFORMATION
RESERVED
SPI SYSTEM
CONFIGURATION
RESERVED
MCSPI_REVISION REVISION
-
MCSPI_SYST
MCSPI_TX0
RESERVED
SYSTEM STATUS
SYSTEM TEST
CHANNEL 0 STATUS
CHANNEL 0 TRANSMITTER
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
351
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-104. SPI Registers (continued)
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
MCSPI_RX0
CHANNEL 0 RECEIVER
SPI0
SPI1
SPI2
SPI3
0x4803 013C
0x481A 013C
0x481A 213C
0x481A 413C
0x4803 0140
0x481A 0140
0x481A 2140
0x481A 4140
MCSPI_CH1CONF CHANNEL 1 CONFIGURATION
0x4803 0144
0x481A 0144
0x481A 2144
0x481A 4144
MCSPI_CH1STAT
MCSPI_CH1CTRL CHANNEL 1 CONTROL
CHANNEL 1 STATUS
0x4803 0148
0x481A 0148
0x481A 2148
0x481A 4148
0x4803 014C
0x481A 014C
0x481A 214C
0x481A 414C
MCSPI_TX1
CHANNEL 1 TRANSMITTER
0x4803 0150
0x481A 0150
0x481A 2150
0x481A 4150
MCSPI_RX1
CHANNEL 1 RECEIVER
0x4803 0154
0x481A 0154
0x481A 2154
0x481A 4154
0x4803 0158
0x481A 0158
0x481A 2158
0x481A 4158
MCSPI_CH2STAT
0x4803 015C
0x481A 015C
0x481A 215C
0x481A 415C
MCSPI_CH2CTRL CHANNEL 2 CONTROL
0x4803 0160
0x481A 0160
0x481A 2160
0x481A 4160
0x4803 0164
0x481A 0164
0x481A 2164
0x481A 4164
0x4803 0168
0x481A 0168
0x481A 2168
0x481A 4168
MCSPI_CH3CONF CHANNEL 3 CONFIGURATION
0x4803 016C
0x481A 016C
0x481A 216C
0x481A 416C
MCSPI_CH3STAT
0x4803 0170
0x481A 0170
0x481A 2170
0x481A 4170
MCSPI_CH3CTRL CHANNEL 3 CONTROL
0x4803 0174
0x481A 0174
0x481A 2174
0x481A 4174
MCSPI_TX3
CHANNEL 3 TRANSMITTER
0x4803 0178
0x481A 0178
0x481A 2178
0x481A 4178
MCSPI_RX3
CHANNEL 3 RECEIVER
0x4803 017C
0x481A 017C
0x481A 217C
0x481A 417C
MCSPI_XFERLEV
EL
0x4803 0180
0x481A 0180
0x481A 2180
0x481A 4180
MCSPI_DAFTX
0x4803 0184 0x4803 019C
0x481A 0184 0x481A 019C
0x481A 2184 0x481A 219C
0x481A 4184 0x481A 419C
-
0x4803 01A0
0x481A 01A0
0x481A 21A0
0x481A 41A0
MCSPI_DAFRX
0x4803 01A4 0x4803 01FF
0x481A 01A4 0x481A 01FF
0x481A 21A4 0x481A 21FF
0x481A 41A4 0x481A 41FF
-
352
Peripheral Information and Timings
MCSPI_CH2CONF CHANNEL 2 CONFIGURATION
CHANNEL 2 STATUS
MCSPI_TX2
CHANNEL 2 TRANSMITTER
MCSPI_RX2
CHANNEL 2 RECEIVER
CHANNEL 3 STATUS
TRANSFER LEVELS
DMA ADDRESS ALIGNED
FIFO TRANSMITTER
RESERVED
DMA ADDRESS ALIGNED
FIFO RECEIVER
RESERVED
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.19.2 SPI Electrical Data/Timing
Table 8-105. Timing Requirements for SPI - Master Mode
(see Figure 8-90 and Figure 8-91)
OPP100/120/166
NO.
MIN
MAX
UNIT
MASTER: SPI0, SPI1, SPI2 (M0) and SPI3 (M0)1 LOAD AT A MAXIMUM OF 5 pF
1
tc(SPICLK)
Cycle time, SPI_CLK (1) (2)
(1)
2
tw(SPICLKL)
Pulse duration, SPI_CLK low
3
tw(SPICLKH)
Pulse duration, SPI_CLK high (1)
4
5
th(SPICLK-MISO)
Hold time, SPI_D[x] valid after SPI_CLK active edge (1)
6
td(SPICLK-MOSI)
Delay time, SPI_CLK active edge to SPI_D[x] transition (1)
7
td(SCS-MOSI)
Delay time, SPI_SCS[x] active edge to SPI_D[x] transition
9
td(SPICLK-SCS)
Delay time, SPI_CLK last edge to SPI_SCS[x]
inactive (1)
ns
SPI2, SPI3
Setup time, SPI_D[x] valid before SPI_CLK active
edge (1)
Delay time, SPI_SCS[x] active to SPI_CLK first
edge (1)
ns
0.5*P - 1 (4)
2.29
tsu(MISO-SPICLK)
td(SCS-SPICLK)
ns
0.5*P - 1 (4)
SPI0, SPI1
4
8
20.8 (3)
ns
2.67
-3.57
ns
3.57
ns
3.57
ns
MASTER_PH
A0 (5)
B-4.2
(6)
ns
MASTER_PH
A1 (5)
A-4.2 (7)
ns
MASTER_PH
A0 (5)
A-4.2 (7)
ns
MASTER_PH
A1 (5)
B-4.2 (6)
ns
MASTER: SPI0, SPI1, SPI2 (M0) and SPI3 (M0) LOAD AT MAX 25pF
MASTER: SPI2 (M1, M2, M3) and SPI3 (M1, M2, M3) 1 to 4 LOAD AT 5 to 25pF
1
(8)
(1)
tw(SPICLKL)
Pulse duration, SPI_CLK low
3
tw(SPICLKH)
Pulse duration, SPI_CLK high (1)
4
tsu(MISO-SPICLK)
Setup time, SPI_D[x] valid before SPI_CLK active
edge (1)
5
th(SPICLK-MISO)
Hold time, SPI_D[x] valid after SPI_CLK active edge (1)
6
td(SPICLK-MOSI)
Delay time, SPI_CLK active edge to SPI_D[x] transition (1)
7
td(SCS-MOSI)
Delay time, SPI_SCS[x] active edge to SPI_D[x] transition
9
(2)
(3)
(4)
(5)
(6)
(7)
Cycle time, SPI_CLK (1) (2)
2
8
(1)
tc(SPICLK)
td(SCS-SPICLK)
td(SPICLK-SCS)
Delay time, SPI_SCS[x] active to SPI_CLK first
edge (1)
Delay time, SPI_CLK last edge to SPI_SCS[x]
inactive (1)
41.7 (8)
ns
0.5*P - 2 (4)
ns
0.5*P - 2 (4)
ns
SPI0, SPI1
4
SPI2, SPI3
6
ns
3.8
-5.5
ns
5.5
ns
5.5
ns
MASTER_PH
A0 (5)
B-3.5
(6)
ns
MASTER_PH
A1 (5)
A-3.5 (7)
ns
MASTER_PH
A0 (5)
A-3.5 (7)
ns
MASTER_PH
A1 (5)
B-3.5 (6)
ns
This timing applies to all configurations regardless of SPI_CLK polarity and which clock edges are used to drive output data and capture
input data.
Related to the SPI_CLK maximum frequency.
Maximum frequency = 48 MHz
P = SPICLK period.
SPI_CLK phase is programmable with the PHA bit of the SPI_CH(i)CONF register.
B = (TCS + 0.5) * TSPICLKREF * Fratio, where TCS is a bit field of the SPI_CH(i)CONF register and Fratio = Even ≥2.
When P = 20.8 ns, A = (TCS + 1) * TSPICLKREF, where TCS is a bit field of the SPI_CH(i)CONF register. When P > 20.8 ns, A = (TCS
+ 0.5) * Fratio * TSPICLKREF, where TCS is a bit field of the SPI_CH(i)CONF register.
Maximum frequency = 24 MHz
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
353
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
PHA=0
EPOL=1
SPI_SCS[x] (Out)
1
3
8
SPI_SCLK (Out)
9
2
POL=0
1
2
3
POL=1
SPI_SCLK (Out)
6
7
SPI_D[x] (Out)
Bit n-1
6
Bit n-3
Bit n-2
Bit 0
Bit n-4
PHA=1
EPOL=1
SPI_SCS[x] (Out)
1
3
8
SPI_SCLK (Out)
9
2
POL=0
1
2
3
POL=1
SPI_SCLK (Out)
6
SPI_D[x] (Out)
Bit n-1
6
Bit n-2
6
Bit n-3
6
Bit 1
Bit 0
Figure 8-90. SPI Master Mode Transmit Timing
354
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
PHA=0
EPOL=1
SPI_SCS[x] (Out)
1
3
8
SPI_SCLK (Out)
9
2
POL=0
1
2
3
POL=1
SPI_SCLK (Out)
4
4
5
SPI_D[x] (In)
5
Bit n-1
Bit n-3
Bit n-2
Bit 0
Bit n-4
PHA=1
EPOL=1
SPI_SCS[x] (Out)
1
3
8
SPI_SCLK (Out)
9
2
POL=0
1
2
3
POL=1
SPI_SCLK (Out)
4
4
5
SPI_D[x] (In)
Bit n-1
5
Bit n-2
Bit n-3
Bit 0
Bit 1
Figure 8-91. SPI Master Mode Receive Timing
Table 8-106. Timing Requirements for SPI - Slave Mode
(see Figure 8-92 and Figure 8-93)
OPP100/120/166
NO.
1
(1)
(2)
(3)
(4)
(5)
MIN
tc(SPICLK)
Cycle time, SPI_CLK (1) (2)
(1)
2
tw(SPICLKL)
Pulse duration, SPI_CLK low
3
tw(SPICLKH)
Pulse duration, SPI_CLK high (1)
4
tsu(MOSI-SPICLK)
Setup time, SPI_D[x] valid before SPI_CLK active edge (1)
5
th(SPICLK-MOSI)
Hold time, SPI_D[x] valid after SPI_CLK active edge
6
td(SPICLK-MISO)
Delay time, SPI_CLK active edge to SPI_D[x] transition (1)
7
td(SCS-MISO)
Delay time, SPI_SCS[x] active edge to SPI_D[x]
transition (5)
8
tsu(SCS-SPICLK)
Setup time, SPI_SCS[x] valid before SPI_CLK first edge (1)
UNIT
62.5 (3)
ns
(4)
ns
0.5*P - 3 (4)
ns
12.92
ns
0.5*P - 3
(1)
MAX
12.92
-4.00
ns
17.1
ns
17.1
ns
12.92
ns
This timing applies to all configurations regardless of SPI_CLK polarity and which clock edges are used to drive output data and capture
input data.
Related to the input maximum frequency supported by the SPI module.
Maximum frequency = 16 MHz
P = SPICLK period.
PHA = 0; SPI_CLK phase is programmable with the PHA bit of the SPI_CH(i)CONF register.
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
355
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-106. Timing Requirements for SPI - Slave Mode (continued)
(see Figure 8-92 and Figure 8-93)
OPP100/120/166
NO.
9
MIN
Hold time, SPI_SCS[x] valid after SPI_CLK last edge (1)
th(SPICLK-SCS)
MAX
12.92
UNIT
ns
PHA=0
EPOL=1
SPI_SCS[x] (In)
1
3
8
SPI_SCLK (In)
2
9
POL=0
1
3
2
POL=1
SPI_SCLK (In)
SPI_D[x] (Out)
6
7
6
Bit n-1
Bit n-2
Bit n-3
Bit 0
Bit n-4
PHA=1
EPOL=1
SPI_SCS[x] (In)
1
3
8
SPI_SCLK (In)
9
2
POL=0
1
2
3
POL=1
SPI_SCLK (In)
6
SPI_D[x] (Out)
Bit n-1
6
6
Bit n-2
Bit n-3
6
Bit 1
Bit 0
Figure 8-92. SPI Slave Mode Transmit Timing
356
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
PHA=0
EPOL=1
SPI_SCS[x] (In)
1
3
8
SPI_SCLK (In)
2
9
POL=0
1
3
2
POL=1
SPI_SCLK (In)
4
4
5
SPI_D[x] (In)
5
Bit n-1
Bit n-3
Bit n-2
Bit 0
Bit n-4
PHA=1
EPOL=1
SPI_SCS[x] (In)
1
3
8
SPI_SCLK (In)
9
2
POL=0
1
2
3
POL=1
SPI_SCLK (In)
4
5
SPI_D[x] (In)
Bit n-1
4
5
Bit n-2
Bit n-3
Bit 1
Bit 0
Figure 8-93. SPI Slave Mode Receive Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
357
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.20 Timers
The device has eight 32-bit general-purpose (GP) timers (TIMER8 - TIMER1) that have the following
features:
• TIMER8, TIMER1 are for software use and do not have an external connection
• Dedicated input trigger for capture mode and dedicated output trigger/pulse width modulation (PWM)
signal
• Interrupts generated on overflow, compare, and capture
• Free-running 32-bit upward counter
• Supported modes:
– Compare and capture modes
– Auto-reload mode
– Start-stop mode
• TIMER[8:1] functional clock is sourced from either the DEVOSC, AUXOSC, AUD_CLK2/1/0, TCLKIN,
or SYSCLK18 27 MHz as selected by the timer clock multiplexers.
• On-the-fly read/write register (while counting)
• Generates interrupts to the ARM, DSP, and Media Controller.
The device has one system watchdog timer that have the following features:
• Free-running 32-bit upward counter
• On-the-fly read/write register (while counting)
• Reset upon occurrence of a timer overflow condition
• The system watchdog timer has two possible clock sources:
– RCOSC32K oscillator
– RTCDIVIDER
• The watchdog timer is used to provide a recovery mechanism for the device in the event of a fault
condition, such as a non-exiting code loop.
For more detailed information on the GP and Watchdog Timers, see the Timers and Watchdog Timer
chapters of the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual
(Literature Number: SPRUGZ8).
8.20.1 Timer Peripheral Register Descriptions
358
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.20.2 Timer Electrical/Data Timing
Table 8-107. Timing Requirements for Timer
(see Figure 8-94)
OPP100/120/166
NO.
1
tw(EVTIH)
2
(1)
MIN
tw(EVTIL)
Pulse duration, high
Pulse duration, low
MAX
UNIT
4P (1)
ns
(1)
ns
4P
P = module clock.
Table 8-108. Switching Characteristics Over Recommended Operating Conditions for Timer
(see Figure 8-94)
NO.
3
4
(1)
OPP100/120/166
PARAMETER
tw(EVTOH)
tw(EVTOL)
MIN
Pulse duration, high
Pulse duration, low
MAX
UNIT
4P-3 (1)
ns
(1)
ns
4P-3
P = module clock.
1
2
TCLKIN
3
4
TIMx_IO
Figure 8-94. Timer Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
359
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.21 Universal Asynchronous Receiver/Transmitter (UART)
The UART performs serial-to-parallel conversions on data received from a peripheral device and parallelto-serial conversion on data received from the CPU. The device provides up to six UART peripheral
interfaces, depending on the selected pin multiplexing.
Each UART has the following features:
• Selectable UART/IrDA (SIR/MIR)/CIR modes
• Dual 64-entry FIFOs for received and transmitted data payload
• Programmable and selectable transmit and receive FIFO trigger levels for DMA and interrupt
generation
• Baud-rate generation based upon programmable divisors N (N=1…16384)
• Two DMA requests and one interrupt request to the system
• Can connect to any RS-232 compliant device.
UART functions include:
• Baud-rate up to 3.6 Mbit/s on UART0, UART1, and UART2
• Baud-rate up to 12 Mbit/s on UART3, UART4, and UART5
• Programmable serial interfaces characteristics
– 5, 6, 7, or 8-bit characters
– Even, odd, or no parity-bit generation and detection
– 1, 1.5, or 2 stop-bit generation
– Flow control: hardware (RTS/CTS) or software (XON/XOFF)
• Additional modem control functions (UART0_DTR, UART0_DSR, UART0_DCD, and UART0_RIN) for
UART0 only; UART1, UART2, UART3, UART4, and UART5 do not support full-flow control signaling.
IR-IrDA functions include:
• Support of IrDA 1.4 slow infrared (SIR, baud-rate up to 115.2 Kbits/s), medium infrared (MIR, baudrate up to 1.152 Mbits/s) and fast infrared (FIR baud-rate up to 4.0 Mbits/s) communications
• Supports framing error, cyclic redundancy check (CRC) error, illegal symbol (FIR), and abort pattern
(SIR, MIR) detection
• 8-entry status FIFO (with selectable trigger levels) available to monitor frame length and frame errors.
IR-CIR functions include:
• Consumer infrared (CIR) remote control mode with programmable data encoding
• Free data format (supports any remote control private standards)
• Selectable bit rate and configurable carrier frequency.
For more detailed information on the UART peripheral, see the UART/IrDA/CIR Module chapter of the
TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
8.21.1 UART Peripheral Register Descriptions
360
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.21.2 UART Electrical/Data Timing
Table 8-109. Timing Requirements for UART
(see Figure 8-95)
OPP100/120/166
NO.
4
(1)
(2)
MAX
Pulse width, receive data bit, 15/30/100pF high or low
0.96U (1)
1.05U (1)
ns
tw(CTS)
Pulse width, receive start bit, 15/30/100pF high or low
(1)
(1)
ns
td(RTS-TX)
Delay time, transmit start bit to transmit data
P (2)
ns
td(CTS-TX)
Delay time, receive start bit to transmit data
P (2)
ns
tw(RX)
5
UNIT
MIN
0.96U
1.05U
U = UART baud time = 1/programmed baud rate
P = Clock period of the reference clock (FCLK, usually 48 MHz).
Table 8-110. Switching Characteristics Over Recommended Operating Conditions for UART
(see Figure 8-95)
NO.
f(baud)
2
3
(1)
OPP100/120/166
PARAMETER
tw(TX)
tw(RTS)
MIN
Maximum programmable baud rate
MAX
15 pF
(UART0/1/2)
5
15 pF
(UART3/4/5)
12
30 pF
0.23
100 pF
0.115
UNIT
MHz
Pulse width, transmit data bit, 15/30/100 pF high or low
U - 2 (1)
U + 2 (1)
ns
Pulse width, transmit start bit, 15/30/100 pF high or low
(1)
U + 2 (1)
ns
U-2
U = UART baud time = 1/programmed baud rate
3
2
UARTx_TXD
Start
Bit
Data Bits
5
4
UARTx_RXD
Start
Bit
Data Bits
Figure 8-95. UART Timing
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
361
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
8.22 Universal Serial Bus (USB2.0)
The device includes two USB2.0 modules which support the Universal Serial Bus Specification Revision
2.0. The following are some of the major USB features that are supported:
• USB 2.0 peripheral at high speed (HS: 480 Mbps) and full speed (FS: 12 Mbps)
• USB 2.0 host at HS, FS, and low speed (LS: 1.5 Mbps)
• Each endpoint (other than endpoint 0, control only) can support all transfer modes (control, bulk,
interrupt, and isochronous)
• Supports high-bandwidth ISO mode
• Supports 16 Transmit (TX) and 16 Receive (RX) endpoints including endpoint 0
• FIFO RAM
– 32K endpoint
– Programmable size
• Includes two integrated PHYs
• RNDIS-like mode for terminating RNDIS-type protocols without using short-packet termination for
support of MSC applications.
• USB OTG extensions — session request protocol (SRP) and host negotiation protocol (HNP)
The USB2.0 peripherals do not support the following features:
• On-chip charge pump (VBUS Power must be generated external to the device.)
• RNDIS mode acceleration for USB sizes that are not multiples of 64 bytes
• Endpoint max USB packet sizes that do not conform to the USB 2.0 spec (for FS/LS: 8, 16, 32, 64, –
and 1023 are defined; for HS: 64, 128, 512, and 1024 are defined
For more detailed information on the USB2.0 peripheral, see the Universal Serial Bus (USB) chapter of
the TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:
SPRUGZ8).
8.22.1 USB2.0 Peripheral Register Descriptions
Table 8-111. USB2.0 Submodules
SUBMODULE
ADDRESS OFFSET
SUBMODULE NAME
0x0000
USBSS registers
0x1000
USB0 controller registers
0x1800
USB1 controller registers
0x2000
CPPI DMA controller registers
0x3000
CPPI DMA scheduler registers
0x4000
CPPI DMA Queue Manager registers
Table 8-112. USB Subsystem (USBSS) Registers (1)
(1)
362
HEX ADDRESS
ACRONYM
REGISTER NAME
0x4740 0000
REVREG
USBSS REVISION
0x4740 0004 - 0x4740 000C
-
0x4740 0010
SYSCONFIG
0x4740 0014 - 0x4740 001C
-
0x4740 0020
EOI
0x4740 0024
IRQSTATRAW
0x4740 0028
IRQSTAT
Reserved
USBSS SYSCONFIG
Reserved
USBSS IRQ_EOI
USBSS IRQ_STATUS_RAW
USBSS IRQ_STATUS
USBSS registers contain the registers that are used to control at the global level and apply to all sub-modules.
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-112. USB Subsystem (USBSS) Registers(1) (continued)
HEX ADDRESS
ACRONYM
0x4740 002C
IRQENABLER
REGISTER NAME
USBSS IRQ_ENABLE_SET
USBSS IRQ_ENABLE_CLR
0x4740 0030
IRQCLEARR
0x4740 0034 - 0x4740 00FC
-
0x4740 0100
IRQDMATHOLDTX00
USBSS IRQ_DMA_THRESHOLD_TX0_0
0x4740 0104
IRQDMATHOLDTX01
USBSS IRQ_DMA_THRESHOLD_TX0_1
0x4740 0108
IRQDMATHOLDTX02
USBSS IRQ_DMA_THRESHOLD_TX0_2
0x4740 010C
IRQDMATHOLDTX03
USBSS IRQ_DMA_THRESHOLD_TX0_3
0x4740 0110
IRQDMATHOLDRX00
USBSS IRQ_DMA_THRESHOLD_RX0_0
0x4740 0114
IRQDMATHOLDRX01
USBSS IRQ_DMA_THRESHOLD_RX0_1
0x4740 0118
IRQDMATHOLDRX02
USBSS IRQ_DMA_THRESHOLD_RX0_2
0x4740 011C
IRQDMATHOLDRX03
USBSS IRQ_DMA_THRESHOLD_RX0_3
0x4740 0120
IRQDMATHOLDTX10
USBSS IRQ_DMA_THRESHOLD_TX1_0
0x4740 0124
IRQDMATHOLDTX11
USBSS IRQ_DMA_THRESHOLD_TX1_1
0x4740 0128
IRQDMATHOLDTX12
USBSS IRQ_DMA_THRESHOLD_TX1_2
0x4740 012C
IRQDMATHOLDTX13
USBSS IRQ_DMA_THRESHOLD_TX1_3
0x4740 0130
IRQDMATHOLDRX10
USBSS IRQ_DMA_THRESHOLD_RX1_0
0x4740 0134
IRQDMATHOLDRX11
USBSS IRQ_DMA_THRESHOLD_RX1_1
Reserved
0x4740 0138
IRQDMATHOLDRX12
USBSS IRQ_DMA_THRESHOLD_RX1_2
0x4740 013C
IRQDMATHOLDRX13
USBSS IRQ_DMA_THRESHOLD_RX1_3
0x4740 0140
IRQDMAENABLE0
USBSS IRQ_DMA_ENABLE_0
0x4740 0144
IRQDMAENABLE1
USBSS IRQ_DMA_ENABLE_1
0x4740 0148 - 0x4740 01FC
-
0x4740 0200
IRQFRAMETHOLDTX00
Reserved
USBSS IRQ_FRAME_THRESHOLD_TX0_0
0x4740 0204
IRQFRAMETHOLDTX01
USBSS IRQ_FRAME_THRESHOLD_TX0_1
0x4740 0208
IRQFRAMETHOLDTX02
USBSS IRQ_FRAME_THRESHOLD_TX0_2
0x4740 020C
IRQFRAMETHOLDTX03
USBSS IRQ_FRAME_THRESHOLD_TX0_3
0x4740 0210
IRQFRAMETHOLDRX00
USBSS IRQ_FRAME_THRESHOLD_RX0_0
0x4740 0214
IRQFRAMETHOLDRX01
USBSS IRQ_FRAME_THRESHOLD_RX0_1
0x4740 0218
IRQFRAMETHOLDRX02
USBSS IRQ_FRAME_THRESHOLD_RX0_2
0x4740 021C
IRQFRAMETHOLDRX03
USBSS IRQ_FRAME_THRESHOLD_RX0_3
0x4740 0220
IRQFRAMETHOLDTX10
USBSS IRQ_FRAME_THRESHOLD_TX1_0
0x4740 0224
IRQFRAMETHOLDTX11
USBSS IRQ_FRAME_THRESHOLD_TX1_1
0x4740 0228
IRQFRAMETHOLDTX12
USBSS IRQ_FRAME_THRESHOLD_TX1_2
0x4740 022C
IRQFRAMETHOLDTX13
USBSS IRQ_FRAME_THRESHOLD_TX1_3
0x4740 0230
IRQFRAMETHOLDRX10
USBSS IRQ_FRAME_THRESHOLD_RX1_0
0x4740 0234
IRQFRAMETHOLDRX11
USBSS IRQ_FRAME_THRESHOLD_RX1_1
0x4740 0238
IRQFRAMETHOLDRX12
USBSS IRQ_FRAME_THRESHOLD_RX1_2
0x4740 023C
IRQFRAMETHOLDRX13
USBSS IRQ_FRAME_THRESHOLD_RX1_3
0x4740 0240
IRQFRAMEENABLE0
USBSS IRQ_FRAME_ENABLE_0
0x4740 0244
IRQFRAMEENABLE1
USBSS IRQ_FRAME_ENABLE_1
0x4740 0248 - 0x4740 0FFC
-
Reserved
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
363
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-113. USB0 Controller Registers
364
HEX ADDRESS
ACRONYM
REGISTER NAME
0x4740 1000
USB0REV
USB0 REVISION
0x4740 1004 - 0x4740 1010
-
0x4740 1014
USB0CTRL
USB0 Control
USB0 Status
0x4740 1018
USB0STAT
0x4740 101C
-
0x4740 1020
USB0IRQMSTAT
Reserved
Reserved
USB0 IRQ_MERGED_STATUS
0x4740 1024
USB0IRQEOI
0x4740 1028
USB0IRQSTATRAW0
USB0 IRQ_EOI
USB0 IRQ_STATUS_RAW_0
0x4740 102C
USB0IRQSTATRAW1
USB0 IRQ_STATUS_RAW_1
0x4740 1030
USB0IRQSTAT0
USB0 IRQ_STATUS_0
0x4740 1034
USB0IRQSTAT1
USB0 IRQ_STATUS_1
0x4740 1038
USB0IRQENABLESET0
USB0 IRQ_ENABLE_SET_0
0x4740 103C
USB0IRQENABLESET1
USB0 IRQ_ENABLE_SET_1
0x4740 1040
USB0IRQENABLECLR0
USB0 IRQ_ENABLE_CLR_0
0x4740 1044
USB0IRQENABLECLR1
USB0 IRQ_ENABLE_CLR_1
0x4740 1048 - 0x4740 106C
-
Reserved
0x4740 1070
USB0TXMODE
USB0 Tx Mode
0x4740 1074
USB0RXMODE
USB0 Rx Mode
0x4740 1078 - 0x4740 107C
-
0x4740 1080
USB0GENRNDISEP1
USB0 Generic RNDIS Size EP1
0x4740 1084
USB0GENRNDISEP2
USB0 Generic RNDIS Size EP2
0x4740 1088
USB0GENRNDISEP3
USB0 Generic RNDIS Size EP3
0x4740 108C
USB0GENRNDISEP4
USB0 Generic RNDIS Size EP4
0x4740 1090
USB0GENRNDISEP5
USB0 Generic RNDIS Size EP5
0x4740 1094
USB0GENRNDISEP6
USB0 Generic RNDIS Size EP6
0x4740 1098
USB0GENRNDISEP7
USB0 Generic RNDIS Size EP7
0x4740 109C
USB0GENRNDISEP8
USB0 Generic RNDIS Size EP8
0x4740 10A0
USB0GENRNDISEP9
USB0 Generic RNDIS Size EP9
0x4740 10A4
USB0GENRNDISEP10
USB0 Generic RNDIS Size EP10
Reserved
0x4740 10A8
USB0GENRNDISEP11
USB0 Generic RNDIS Size EP11
0x4740 10AC
USB0GENRNDISEP12
USB0 Generic RNDIS Size EP12
0x4740 10B0
USB0GENRNDISEP13
USB0 Generic RNDIS Size EP13
0x4740 10B4
USB0GENRNDISEP14
USB0 Generic RNDIS Size EP14
USB0 Generic RNDIS Size EP15
0x4740 10B8
USB0GENRNDISEP15
0x4740 10BC - 0x4740 10CC
-
0x4740 10D0
USB0AUTOREQ
0x4740 10D4
USB0SRPFIXTIME
0x4740 10D8
USB0TDOWN
0x4740 10DC
-
Reserved
USB0 Auto Req
USB0 SRP Fix Time
USB0 Teardown
Reserved
0x4740 10E0
USB0UTMI
0x4740 10E4
USB0UTMILB
0x4740 10E8
USB0MODE
0x4740 10E8 - 0x4740 13FF
-
Reserved
0x4740 1400 - 0x4740 1468
-
USB0 Mentor Core Registers/FIFOs
0x4740 146C
USB0_HWVERS
0x4740 1470 - 0x4740 159C
-
USB0 Mentor Core Registers/FIFOs
0x4740 15A0 - 0x4740 17FC
-
Reserved
Peripheral Information and Timings
USB0 PHY UTMI
USB0 MGC UTMI Loopback
USB0 Mode
USB0 Mentor Core Hardware Version Register
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-114. USB1 Controller Registers
HEX ADDRESS
ACRONYM
REGISTER NAME
0x4740 1800
USB1REV
USB1 Revision
0x4740 1804 - 0x4740 1810
-
0x4740 1814
USB1CTRL
USB1 Control
USB1 Status
0x4740 1818
USB1STAT
0x4740 181C
-
0x4740 1820
USB1IRQMSTAT
Reserved
Reserved
USB1 IRQ_MERGED_STATUS
0x4740 1824
USB1IRQEOI
0x4740 1828
USB1IRQSTATRAW0
USB1 IRQ_EOI
USB1 IRQ_STATUS_RAW_0
0x4740 182C
USB1IRQSTATRAW1
USB1 IRQ_STATUS_RAW_1
0x4740 1830
USB1IRQSTAT0
USB1 IRQ_STATUS_0
0x4740 1834
USB1IRQSTAT1
USB1 IRQ_STATUS_1
0x4740 1838
USB1IRQENABLESET0
USB1 IRQ_ENABLE_SET_0
0x4740 183C
USB1IRQENABLESET1
USB1 IRQ_ENABLE_SET_1
0x4740 1840
USB1IRQENABLECLR0
USB1 IRQ_ENABLE_CLR_0
0x4740 1844
USB1IRQENABLECLR1
USB1 IRQ_ENABLE_CLR_1
0x4740 1848 - 0x4740 186C
-
Reserved
0x4740 1870
USB1TXMODE
USB1 Tx Mode
0x4740 1874
USB1RXMODE
USB1 Rx Mode
0x4740 1878 - 0x4740 187C
-
0x4740 1880
USB1GENRNDISEP1
USB1 Generic RNDIS Size EP1
0x4740 1884
USB1GENRNDISEP2
USB1 Generic RNDIS Size EP2
0x4740 1888
USB1GENRNDISEP3
USB1 Generic RNDIS Size EP3
0x4740 188C
USB1GENRNDISEP4
USB1 Generic RNDIS Size EP4
0x4740 1890
USB1GENRNDISEP5
USB1 Generic RNDIS Size EP5
0x4740 1894
USB1GENRNDISEP6
USB1 Generic RNDIS Size EP6
0x4740 1898
USB1GENRNDISEP7
USB1 Generic RNDIS Size EP7
0x4740 189C
USB1GENRNDISEP8
USB1 Generic RNDIS Size EP8
0x4740 18A0
USB1GENRNDISEP9
USB1 Generic RNDIS Size EP9
0x4740 18A4
USB1GENRNDISEP10
USB1 Generic RNDIS Size EP10
Reserved
0x4740 18A8
USB1GENRNDISEP11
USB1 Generic RNDIS Size EP11
0x4740 18AC
USB1GENRNDISEP12
USB1 Generic RNDIS Size EP12
0x4740 18B0
USB1GENRNDISEP13
USB1 Generic RNDIS Size EP13
0x4740 18B4
USB1GENRNDISEP14
USB1 Generic RNDIS Size EP14
USB1 Generic RNDIS Size EP15
0x4740 18B8
USB1GENRNDISEP15
0x4740 18BC - 0x4740 18CC
-
0x4740 18D0
USB1AUTOREQ
0x4740 18D4
USB1SRPFIXTIME
0x4740 18D8
USB1TDOWN
0x4740 18DC
-
Reserved
USB1 Auto Req
USB1 SRP Fix Time
USB1 Teardown
Reserved
0x4740 18E0
USB1UTMI
0x4740 18E4
USB1UTMILB
USB1 PHY UTMI
0x4740 18E8
USB1MODE
0x4740 18E8 - 0x4740 1BFF
-
Reserved
0x4740 1C00 - 0x4740 1C68
-
USB1 Mentor Core Registers
0x4740 1C6C
USB1HWVERS
0x4740 1C70 - 0x4740 1D9C
-
USB1 Mentor Core Registers
0x4740 1DA0 - 0x4740 1FFC
-
Reserved
USB1 MGC UTMI Loopback
USB1 Mode
USB1 Mentor Core Hardware Version Register
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
365
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-115. CPPI DMA Controller Registers
HEX ADDRESS
ACRONYM
REGISTER NAME
0x4740 2000
DMAREVID
Revision Register
0x4740 2004
TDFDQ
0x4740 2008
DMAEMU
Teardown Free Descriptor Queue Control
Emulation Control Register
0x4740 200C
-
0x4740 2010
DMAMEM1BA
CPPI Mem1 Base Address Register
0x4740 2014
DMAMEM1MASK
CPPI Mem1 Mask Address Register
0x4740 200C - 0x4740 27FF
-
0x4740 2800
TXGCR0
0x4740 2804
-
Reserved
Reserved
Tx Channel 0 Global Configuration Register
Reserved
0x4740 2808
RXGCR0
0x4740 280C
RXHPCRA0
Rx Channel 0 Host Packet Configuration Register A
0x4740 2810
RXHPCRB0
Rx Channel 0 Host Packet Configuration Register B
0x4740 2814 - 0x4740 281C
-
0x4740 2820
TXGCR1
0x4740 2824
-
0x4740 2828
RXGCR1
0x4740 282C
RXHPCRA1
Rx Channel 1 Host Packet Configuration Register A
0x4740 2830
RXHPCRB1
Rx Channel 1 Host Packet Configuration Register B
0x4740 2834 - 0x4740 283C
-
0x4740 2840
TXGCR2
0x4740 2844
-
0x4740 2848
RXGCR2
0x4740 284C
RXHPCRA2
Rx Channel 2 Host Packet Configuration Register A
Rx Channel 2 Host Packet Configuration Register B
0x4740 2850
RXHPCRB2
0x4740 2854 - 0x4740 285F
-
0x4740 2860
TXGCR3
Rx Channel 0 Global Configuration Register
Reserved
Tx Channel 1 Global Configuration Register
Reserved
Rx Channel 1 Global Configuration Register
Reserved
Tx Channel 2 Global Configuration Register
Reserved
Rx Channel 2 Global Configuration Register
Reserved
Tx Channel 3 Global Configuration Register
0x4740 2864
-
0x4740 2868
RXGCR3
0x4740 286C
RXHPCRA3
Rx Channel 3 Host Packet Configuration Register A
Rx Channel 3 Host Packet Configuration Register B
0x4740 2870
RXHPCRB3
0x4740 2880 - 0x4740 2B9F
-
0x4740 2BA0
TXGCR29
0x4740 2BA4
-
Reserved
Rx Channel 3 Global Configuration Register
...
Tx Channel 29 Global Configuration Register
Reserved
0x4740 2BA8
RXGCR29
0x4740 2BAC
RXHPCRA29
Rx Channel 29 Global Configuration Register
Rx Channel 29 Host Packet Configuration Register A
0x4740 2BB0
RXHPCRB29
Rx Channel 29 Host Packet Configuration Register B
0x4740 2BB4 - 0x4740 2FFF
-
Reserved
Table 8-116. CPPI DMA Scheduler Registers
366
HEX ADDRESS
ACRONYM
0x4740 3000
DMA_SCHED_CTRL
0x4740 3804 - 0x4740 38FF
-
0x4740 3800
WORD0
CPPI DMA Scheduler Table Word 0
0x4740 3804
WORD1
CPPI DMA Scheduler Table Word 1
…
…
0x4740 38F8
WORD62
CPPI DMA Scheduler Table Word 62
0x4740 38FC
WORD63
CPPI DMA Scheduler Table Word 63
Peripheral Information and Timings
REGISTER NAME
CPPI DMA Scheduler Control Register
Reserved
…
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
Table 8-116. CPPI DMA Scheduler Registers (continued)
HEX ADDRESS
ACRONYM
0x4740 38FF - 0x4740 3FFF
-
REGISTER NAME
Reserved
Table 8-117. CPPI DMA Queue Manager Registers
HEX ADDRESS
ACRONYM
0x4740 4000
QMGRREVID
0x4740 4004
-
0x4740 4008
DIVERSION
REGISTER NAME
Queue Manager Revision
Reserved
Queue Manager Queue Diversion
0x4740 400C - 0x4740 401F
-
0x4740 4020
FDBSC0
Reserved
Queue Manager Free Descriptor/Buffer Starvation Count 0
0x4740 4024
FDBSC1
Queue Manager Free Descriptor/Buffer Starvation Count 1
0x4740 4028
FDBSC2
Queue Manager Free Descriptor/Buffer Starvation Count 2
0x4740 402C
FDBSC3
Queue Manager Free Descriptor/Buffer Starvation Count 3
0x4740 4030
FDBSC4
Queue Manager Free Descriptor/Buffer Starvation Count 4
0x4740 4034
FDBSC5
Queue Manager Free Descriptor/Buffer Starvation Count 5
0x4740 4038
FDBSC6
Queue Manager Free Descriptor/Buffer Starvation Count 6
0x4740 403C
FDBSC7
Queue Manager Free Descriptor/Buffer Starvation Count 7
0x4740 4030 - 0x4740 407C
-
0x4740 4080
LRAM0BASE
Queue Manager Linking RAM Region 0 Base Address
0x4740 4084
LRAM0SIZE
Queue Manager Linking RAM Region 0 Size
0x4740 4088
LRAM1BASE
Queue Manager Linking RAM Region 1 Base Address
0x4740 408C
-
0x4740 4090
PEND0
Queue Manager Queue Pending 0
0x4740 4094
PEND1
Queue Manager Queue Pending 1
0x4740 4098
PEND2
Queue Manager Queue Pending 2
0x4740 409C
PEND3
Queue Manager Queue Pending 3
0x4740 40A0
PEND4
Queue Manager Queue Pending 4
0x4740 40A4 - 0x4740 4FFF
-
Reserved
Reserved
Reserved
0x4740 5000 + 16xR
QMEMRBASE0
Memory Region 0 Base Address (R ranges from 0 to 15)
0x4740 5000 + 16xR + 4
QMEMRCTRL0
Memory Region 0 Control 0 (R ranges from 0 to 15)
0x4740 5000 + 16xR + 8
-
Reserved
0x4740 5000 + 16xR + C
-
Reserved
0x4740 5010 – 0x4740 50EF
-
...
0x4740 5000 + 16xR
QMEMRBASE15
Memory Region 15 Base Address (R ranges from 0 to 15)
0x4740 5000 + 16xR + 4
QMEMRCTRL15
Memory Region 15 Control (R ranges from 0 to 15)
0x4740 5000 + 16xR + 8
-
Reserved
0x4740 5000 + 16xR + C
-
Reserved
0x4740 5080 - 0x4740 5FFF
-
Reserved
0x4740 6000 + 16xN
-
Reserved
0x4740 6000 + 16xN + 4
-
Reserved
0x4740 6000 + 16xN + 8
-
Reserved
0x4740 6000 + 16xN + C
CTRLD0
0x4740 6010 – 0x4740 69AF
-
...
0x4740 6000 + 16xN
-
Reserved
0x4740 6000 + 16xN + 4
-
Reserved
Reserved
0x4740 6000 + 16xN + 8
-
0x4740 6000 + 16xN + C
CTRLD155
0x4740 69B0 - 0x4740 6FFF
-
Queue N Register D (N ranges from 0 to 155)
Queue N Register D (N ranges from 0 to 155)
Reserved
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
367
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
Table 8-117. CPPI DMA Queue Manager Registers (continued)
368
HEX ADDRESS
ACRONYM
REGISTER NAME
0x4740 7000 + 16xN
QSTATA0
Queue N Status A (N ranges from 0 to 155)
0x4740 7000 + 16xN + 4
QSTATB0
Queue N Status B (N ranges from 0 to 155)
0x4740 7000 + 16xN + 8
QSTATC0
Queue N Status C (N ranges from 0 to 155)
0x4740 7000 + 16xN + C
-
Reserved
0x4740 7010 – 0x4740 79AF
-
...
0x4740 7000 + 16xN
QSTATA155
Queue N Status A (N ranges from 0 to 155)
0x4740 7000 + 16xN + 4
QSTATB155
Queue N Status B (N ranges from 0 to 155)
Queue N Status C (N ranges from 0 to 155)
0x4740 7000 + 16xN + 8
QSTATC155
0x4740 7000 + 16xN + C
-
Reserved
0x4740 79B0 - 0x4740 7FFF
-
Reserved
Peripheral Information and Timings
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
8.22.2 USB2.0 Electrical Data/Timing
Table 8-118. Switching Characteristics Over Recommended Operating Conditions for USB2.0
(see Figure 8-96)
OPP100/120/166
NO.
1
tr(D)
Rise time, USBx_DP and USBx_DM signals (1)
(1)
FULL SPEED
12 Mbps
HIGH SPEED
480 Mbps
MIN
MAX
MIN
MAX
MIN
75
300
4
20
0.5
UNIT
MAX
ns
2
tf(D)
Fall time, USBx_DP and USBx_DM signals
75
300
4
20
0.5
3
trfM
Rise/Fall time, matching (2)
80
125
90
111
–
–
%
4
VCRS
Output signal cross-over voltage (1)
1.3
2
1.3
2
–
–
V
ns
5
tjr(source)NT
Source (Host) Driver jitter, next transition
tjr(FUNC)NT
Function Driver jitter, next transition
tjr(source)PT
Source (Host) Driver jitter, paired transition (4)
tjr(FUNC)PT
Function Driver jitter, paired transition
7
tw(EOPT)
Pulse duration, EOP transmitter
1250
8
tw(EOPR)
Pulse duration, EOP receiver (5)
670
6
9
t(DRATE)
Data Rate
10
ZDRV
Driver Output Resistance
11
ZINP
Receiver Input Impedance (6)
(1)
(2)
(3)
(4)
(5)
(6)
LOW SPEED
1.5 Mbps
PARAMETER
2
2
(3)
25
2
(3)
ns
1
1
(3)
ns
10
1
(3)
ns
–
ns
1500
160
175
82
–
–
–
–
1.5
300
ns
ns
Mbp
480
s
12
28
49.5
40.5
49.5
Ω
300
–
–
–
kΩ
Low Speed: CL = 200 pF, Full Speed: CL = 50 pF, High Speed: CL = 50 pF
tRFM = (tr/tf) x 100. [Excluding the first transaction from the Idle state.]
For more detailed information, see the Universal Serial Bus Specification Revision 2.0, Chapter 7, Electrical.
tjr = tpx(1) - tpx(0)
Must accept as valid EOP.
These values do not include the external resistors required per USB 2.0 specification.
USBx_DM
VCRS
USBx_DP
t per − t jr
90% VOH
10% VOL
tr
tf
Figure 8-96. USB2.0 Integrated Transceiver Interface Timing
For more detailed information on USB2.0 board design, routing, and layout guidelines, see the USB 2.0
Board Design and Layout Guidelines Application Report (Literature Number: SPRAAR7).
Peripheral Information and Timings
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
369
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
9 Device and Documentation Support
9.1
9.1.1
Device Support
Development Support
TI offers an extensive line of development tools, including tools to evaluate the performance of the
processors, generate code, develop algorithm implementations, and fully integrate and debug software
and hardware modules. The support documentation for the tools is electronically available within the Code
Composer Studio™ Integrated Development Environment (IDE).
The following products support development of TMS320DM814x processor applications:
Software Development Tools: Code Composer Studio™ Integrated Development Environment (IDE):
including Editor C/C++/Assembly Code Generation, and Debug plus additional development tools
Scalable, Real-Time Foundation Software (DSP/BIOS™), which provides the basic run-time target
software needed to support any DaVinci Digital Media Processor application.
Hardware Development Tools: Extended Development System (XDS™) Emulator
For a complete listing of development-support tools for the DM814x DaVinci™ Digital Media Processor
platform, visit the Texas Instruments website at www.ti.com. For information on pricing and availability,
contact the nearest TI field sales office or authorized distributor.
9.1.2
Device and Development-Support Tool Nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all
DSP + ARM devices and support tools. Each DSP + ARM commercial family member has one of three
prefixes: TMX, TMP, or TMS (for example, TMX320DM8148BCYE0). Texas Instruments recommends two
of three possible prefix designators for its support tools: TMDX and TMDS. These prefixes represent
evolutionary stages of product development from engineering prototypes (TMX/TMDX) through fully
qualified production devices/tools (TMS/TMDS).
Device development evolutionary flow:
TMX
Experimental device that is not necessarily representative of the final device's electrical
specifications.
TMP
Final silicon die that conforms to the device's electrical specifications but has not completed
quality and reliability verification.
TMS
Fully-qualified production device.
Support tool development evolutionary flow:
TMDX
Development-support product that has not yet completed Texas Instruments internal
qualification testing.
TMDS
Fully qualified development-support product.
TMX and TMP devices and TMDX development-support tools are shipped against the following
disclaimer:
"Developmental product is intended for internal evaluation purposes."
TMS devices and TMDS development-support tools have been characterized fully, and the quality and
reliability of the device have been demonstrated fully. TI's standard warranty applies.
Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard
production devices. Texas Instruments recommends that these devices not be used in any production
system because their expected end-use failure rate still is undefined. Only qualified production devices are
to be used.
370
Device and Documentation Support
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
TMS320DM8148, TMS320DM8147
www.ti.com
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
TI device nomenclature also includes a suffix with the device family name. This suffix indicates the
package type (for example, CYE), the temperature range (for example, "Blank" is the commercial
temperature range), and the device speed range in megahertz (for example, "Blank" is the default [600MHz ARM, 500-MHz DSP]).
Figure 9-1 provides a legend for reading the complete device name for any TMS320DM814x platform
member.
For device part numbers and further ordering information of TMS320DM814x devices in the CYE package
type, see the TI website (www.ti.com) or contact your TI sales representative.
For additional description of the device nomenclature markings on the die, see the TMS320DM814x
DaVinci™ Digital Media Processors Silicon Errata (Silicon Revision 2.1) (Literature Number: SPRZ343).
TMS
320 DM8148 ( )
PREFIX
TMX = Experimental Device
TMS = Qualified Device
DEVICE FAMILY
320 = TMS320™ DSP Family
DEVICE
DM814x DaVinci™ Digital Media Processors
DM8148
DM8147
CYE
( )
( )
DEVICE SPEED RANGE
Blank = 600-MHz ARM, 500-MHz DSP
0 = 720-MHz ARM, 600-MHz DSP
1 = 1000-MHz ARM, 700-MHZ DSP
1 = 1000-MHz ARM, 750-MHZ DSP [SR3.0 only]
2 = 1000-MHz ARM, 750-MHz DSP
TEMPERATURE RANGE
Blank = 0°C to 90°C, Commercial Temperature
D = -40°C to 90°C, Industrial Temperature
A = -40°C to 105°C, Extended Temperature
(A)
PACKAGE TYPE
CYE = 684-Pin Plastic BGA, with Pb-Free Die Bump
and Solder Ball
SILICON REVISION
B = Revision 2.1
C = Revision 3.0 (Other)
S = Revision 3.0 (Video Security)
A.
B.
C.
BGA = Ball Grid Array
For actual device part numbers (P/Ns) and ordering information, see the TI website (http://www.ti.com).
The TEMPERATURE RANGE values are specified over operating junction temperature.
Figure 9-1. Device Nomenclature(B)(C)
9.2
Documentation Support
The following document describes the DM814x DaVinci™ Digital Media Processors.
SPRUGZ8
9.3
TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual.
Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the
respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views;
see TI's Terms of Use.
TI E2E Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and
help solve problems with fellow engineers.
TI Embedded Processors Wiki Texas Instruments Embedded Processors Wiki. Established to help
developers get started with Embedded Processors from Texas Instruments and to foster
innovation and growth of general knowledge about the hardware and software surrounding
these devices.
Device and Documentation Support
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
Copyright © 2011–2013, Texas Instruments Incorporated
371
TMS320DM8148, TMS320DM8147
SPRS647E – MARCH 2011 – REVISED DECEMBER 2013
www.ti.com
10 Mechanical
The device package has been specially engineered with a new technology called Via Channel™. The Via
Channel technology allows larger than normal PCB via sizes and reduced PCB signal layers to be used in
a PCB design with this 0.8-mm pitch package, and will substantially reduce PCB costs. Via Channel also
allows PCB routing in only two signal layers (four layers total) due to the increased layer efficiency of the
Via Channel™ BGA technology.
10.1 Thermal Data for CYE-04 (Top Hat)
Table 10-1. Thermal Resistance Characteristics (PBGA Package) [CYE-04] (Thinner Top Hat)
NO.
°C/W (1)
AIR FLOW (m/s) (2)
N/A
1
RΘJC
Junction-to-case
0.39
2
RΘJB
Junction-to-board
3.87
N/A
3
RΘJA
Junction-to-free air
11.67
0.00
8.59
1.00
RΘJMA
Junction-to-moving air
7.80
2.00
7
7.33
3.00
8
0.19
0.00
10
0.20
1.00
0.20
2.00
12
0.21
3.00
13
3.44
0.00
15
3.37
1.00
3.26
2.00
3.17
3.00
5
6
11
16
PsiJT
PsiJB
Junction-to-package top
Junction-to-board
17
(1)
(2)
These measurements were conducted in a JEDEC defined 2S2P system (with the exception of the Theta JC [RΘJC] measurement,
which was conducted in a JEDEC defined 1S0P system) and will change based on environment as well as application. For more
information, see these EIA/JEDEC standards:
• JESD51-2, Integrated Circuits Thermal Test Method Environment Conditions - Natural Convection (Still Air)
• JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
• JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
• JESD51-9, Test Boards for Area Array Surface Mount Packages
Power dissipation of 2 W and an ambient temperature of 70ºC is assumed.
m/s = meters per second
10.2 Packaging Information
The following packaging information and addendum reflect the most current data available for the
designated device(s). This data is subject to change without notice and without revision of this document.
372
Mechanical
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320DM8148 TMS320DM8147
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
DM8147BCIS0
OBSOLETE
FCBGA
CYE
684
TBD
Call TI
Call TI
DM8147SCIS0
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
DVITDM8148CCYE1
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148CCYE1
HPSDM8148CCYE2
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148CCYE2
MTDM8148CCYE2
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148CCYE2
TDA1MDRCCYEA0
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148CCYEA0
TMS320DM8147BCYE0
OBSOLETE
FCBGA
CYE
684
TBD
Call TI
Call TI
TMS320DM8147BCYE0
TMS320DM8147BCYE1
OBSOLETE
FCBGA
CYE
684
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8147BCYE1
TMS320DM8147BCYE2
ACTIVE
FCBGA
CYE
684
TBD
Call TI
Call TI
0 to 90
TMS320DM8147BCYE2
TMS320DM8147SCYE0
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
0 to 90
TMS320DM8147SCYE0
TMS320DM8147SCYE1
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
0 to 90
TMS320DM8147SCYE1
TMS320DM8147SCYE2
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
0 to 90
TMS320DM8147SCYE2
TMS320DM8148BCYE0
OBSOLETE
FCBGA
CYE
684
TBD
Call TI
Call TI
0 to 90
TMS320DM8148BCYE0
TMS320DM8148BCYE1
OBSOLETE
FCBGA
CYE
684
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
0 to 90
TMS320DM8148BCYE1
TMS320DM8148BCYE2
OBSOLETE
FCBGA
CYE
684
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
0 to 90
TMS320DM8148BCYE2
TMS320DM8148BCYE2F
OBSOLETE
FCBGA
CYE
684
TBD
Call TI
Call TI
TMS320DM8148CCYE0
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148CCYE0
TMS320DM8148CCYE1
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148CCYE1
TMS320DM8148CCYE2
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148CCYE2
Addendum-Page 1
TMS320DM8147BCYE0
0 to 90
TMS320DM8147SCYE0
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
15-Apr-2017
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
TMS320DM8148CCYEA0
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148CCYEA0
TMS320DM8148SCYE0
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148SCYE0
TMS320DM8148SCYE1
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148SCYE1
TMS320DM8148SCYE2
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148SCYE2
TMS320DM8148SCYEA0
ACTIVE
FCBGA
CYE
684
60
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8148SCYEA0
ZDM8147L3MOBCYE1
OBSOLETE
FCBGA
CYE
684
Green (RoHS
& no Sb/Br)
SNAGCU
Level-4-250C-72 HR
TMS320DM8147BCYE1
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2017
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated