Altera EP20K600E 1. enhanced configuration devices (epc4, epc8, and epc16) data sheet Datasheet

1. Enhanced Configuration Devices
(EPC4, EPC8, and EPC16) Data Sheet
CF52002-2.8
Features
This chapter describes the EPC4, EPC8, and EPC16 enhanced configuration devices
(EPC).
■
Single-chip configuration solution for Altera® ACEX® 1K, APEX™ 20K (including
APEX 20K, APEX 20KC, and APEX 20KE), APEX II, Arria® GX, Cyclone®, Cyclone
II, FLEX® 10K (including FLEX 10KE and FLEX 10KA), Mercury™, Stratix® II, and
Stratix II GX devices
■
Contains 4-, 8-, and 16-Mbit flash memories for configuration data storage
■
■
Standard flash die and a controller die combined into single stacked chip package
■
External flash interface supports parallel programming of flash and external
processor access to unused portions of memory
■
■
Flash memory block/sector protection capability via external flash interface
■
Supported in EPC16 and EPC4 devices
Page mode support for remote and local reconfiguration with up to eight
configurations for the entire system
■
Compatible with Stratix series Remote System Configuration feature
■
Supports byte-wide configuration mode fast passive parallel (FPP); 8-bit data
output per DCLK cycle
■
Supports true n-bit concurrent configuration (n = 1, 2, 4, and 8) of Altera FPGAs
■
Pin-selectable 2-ms or 100-ms power-on reset (POR) time
■
Configuration clock supports programmable input source and frequency synthesis
■
■
Multiple configuration clock sources supported (internal oscillator and
external clock input pin)
■
External clock source with frequencies up to 100 MHz
■
Internal oscillator defaults to 10 MHz; Programmable for higher frequencies of
33, 50, and 66 MHz
■
Clock synthesis supported via user programmable divide counter
Available in the 100-pin plastic quad flat pack (PQFP) and the 88-pin Ultra
FineLine BGA® (UFBGA) packages
■
© December 2009
On-chip decompression feature almost doubles the effective configuration
density
Vertical migration between all devices supported in the 100-pin PQFP package
■
Supply voltage of 3.3 V (core and I/O)
■
Hardware compliant with IEEE Std. 1532 in-system programmability (ISP)
specification
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–2
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
f
■
Supports ISP via Jam Standard Test and Programming Language (STAPL)
■
Supports JTAG boundary scan
■
nINIT_CONF pin allows private JTAG instruction to start FPGA configuration
■
Internal pull-up resistor on nINIT_CONF always enabled
■
User programmable weak internal pull-up resistors on nCS and OE pins
■
Internal weak pull-up resistors on external flash interface address and control
lines, bus hold on data lines
■
Standby mode with reduced power consumption
For more information about FPGA configuration schemes and advanced features,
refer to the appropriate FPGA family chapter in the Configuration Handbook.
Functional Description
The Altera enhanced configuration device is a single-device, high-speed, advanced
configuration solution for very high-density FPGAs. The core of an enhanced
configuration device is divided into two major blocks: a configuration controller and a
flash memory. The flash memory is used to store configuration data for systems made
up of one or more Altera FPGAs. Unused portions of the flash memory can be used to
store processor code or data that can be accessed via the external flash interface after
FPGA configuration is complete. Table 1–1 summarizes the features of Altera
configuration devices and the amount of configuration space they hold.
Table 1–1. Altera Configuration Devices
Memory Size
(bits)
On-Chip
Decompression
Support
ISP
Support
Cascading
Support
Reprogrammable
Operating
Voltage (V)
EPC4
4,194,304
Yes
Yes
No
Yes
3.3
EPC8
8,388,608
Yes
Yes
No
Yes
3.3
EPC16
16,777,216
Yes
Yes
No
Yes
3.3
Device
Table 1–2 lists the supported configuration devices required to configure an ACEX 1K,
APEX 1K, APEX 20K, APEX 20KC, APEX 20KE, APEX II, Arria GX, Cyclone,
Cyclone II, FLEX 10K, FLEX 10KA, FLEX 10KE, Stratix, Stratix GX, Stratix II, Stratix II
GX, or Mercury device.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
1–3
Table 1–2. Configuration Devices Required (Part 1 of 3)
Family
Arria GX
Data Size (Bits)
(1)
EPC4 (2)
EPC8 (2)
EPC16 (2)
EP1AGX20C
9,640,672
—
—
1
EP1AGX35C
9,640,672
—
—
1
16,951,824
—
—
1
16,951,824
—
—
1
EP1AGX90E
25,699,104
—
—
1
EP1S10
3,534,640
1
1
1
EP1S20
5,904,832
1
1
1
EP1S25
7,894,144
—
1
1
EP1S30
10,379,368
—
1
1
EP1S40
12,389,632
—
1
1
EP1S60
17,543,968
—
—
1
EP1S80
23,834,032
—
—
1
EP1SGX10
3,534,640
1
1
1
EP1SGX25
7,894,144
—
1
1
EP1SGX40
12,389,632
—
1
1
EP2S15
4,721,544
1
1
1
EP2S30
9,640,672
—
1
1
EP2S60
16,951,824
—
—
1
EP2S90
25,699,104
—
—
—
EP2S130
37,325,760
—
—
—
EP2S180
49,814,760
—
—
—
EP2SGX30C
9,640,672
—
—
1
EP2SGX30D
9,640,672
—
—
1
Device
EP1AGX35D
EP1AGX50C
EP1AGX50D
EP1AGX60C
EP1AGX60D
EP1AGX60E
Stratix
Stratix GX
Stratix II
Stratix II GX
Cyclone
© December 2009
Altera Corporation
EP2SGX60C
16,951,824
—
—
1
EP2SGX60D
16,951,824
—
—
1
EP2SGX60E
16,951,824
—
—
1
EP2SGX90E
25,699,104
—
—
—
EP2SGX90F
25,699,104
—
—
—
EP2SGX130G
37,325,760
—
—
—
EP1C3
627,376
1
1
1
EP1C4
924,512
1
1
1
EP1C6
1,167,216
1
1
1
EP1C12
2,326,528
1
1
1
EP1C20
3,559,608
1
1
1
Configuration Handbook (Complete Two-Volume Set)
1–4
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
Table 1–2. Configuration Devices Required (Part 2 of 3)
Family
Cyclone II
ACEX 1K
APEX 20K
APEX 20KC
APEX 20KE
APEX II
FLEX 10K
Configuration Handbook (Complete Two-Volume Set)
Data Size (Bits)
(1)
EPC4 (2)
EPC8 (2)
EPC16 (2)
EP2C5
1,223,980
1
1
1
EP2C8
1,983,792
1
1
1
EP2C20
3,930,986
1
1
1
EP2C35
7,071,234
—
1
1
EP2C50
9,122,148
—
1
1
EP2C70
10,249,694
—
1
1
EP1K10
159,160
1
1
1
EP1K30
473,720
1
1
1
EP1K50
784,184
1
1
1
EP1K100
1,335,720
1
1
1
EP20K100
993,360
1
1
1
EP20K200
1,950,800
1
1
1
EP20K400
3,880,720
1
1
1
EP20K200C
196,8016
1
1
1
EP20K400C
390,9776
1
1
1
Device
EP20K600C
567,3936
1
1
1
EP20K1000C
8,960,016
—
1
1
EP20K30E
354,832
1
1
1
EP20K60E
648,016
1
1
1
EP20K100E
1,008,016
1
1
1
EP20K160E
1,524,016
1
1
1
EP20K200E
1,968,016
1
1
1
EP20K300E
2,741,616
1
1
1
EP20K400E
3,909,776
1
1
1
EP20K600E
5,673,936
1
1
1
EP20K1000E
8,960,016
—
1
1
EP20K1500E
12,042,256
—
1
1
EP2A15
4,358,512
1
1
1
EP2A25
6,275,200
1
1
1
EP2A40
9,640,528
—
1
1
EP2A70
17,417,088
—
—
1
EPF10K10
118,000
1
1
1
EPF10K20
231,000
1
1
1
EPF10K30
376,000
1
1
1
EPF10K40
498,000
1
1
1
EPF10K50
621,000
1
1
1
EPF10K70
892,000
1
1
1
EPF10K100
1,200,000
1
1
1
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
1–5
Table 1–2. Configuration Devices Required (Part 3 of 3)
Data Size (Bits)
(1)
EPC4 (2)
EPC8 (2)
EPC16 (2)
EPF10K10A
120,000
1
1
1
EPF10K30A
406,000
1
1
1
EPF10K50V
621,000
1
1
1
EPF10K100A
1,200,000
1
1
1
EPF10K130V
1,600,000
1
1
1
EPF10K250A
3,300,000
1
1
1
EPF10K30E
473,720
1
1
1
EPF10K50E
784,184
1
1
1
EPF10K50S
784,184
1
1
1
EPF10K100B
1,200,000
1
1
1
EPF10K100E
1,335,720
1
1
1
EPF10K130E
1,838,360
1
1
1
EPF10K200E
2,756,296
1
1
1
EPF10K200S
2,756,296
1
1
1
EP1M120
1,303,120
1
—
1
EP1M350
4,394,032
1
—
1
Family
FLEX 10KA
FLEX 10KE
Mercury
Device
Notes to Table 1–2:
(1) Raw Binary Files (.rbf) were used to determine these sizes.
(2) These values with the enhanced configuration device compression feature enabled.
f
For more information about additional enhanced configuration devices, refer to the
Process Change Notification PCN0506: Addition of Intel Flash Memory As Source For
EPC4, EPC8 and EPC16 Enhanced Configuration Devices and Using the Intel Flash
Memory-Based EPC4, EPC8 and EPC16 Devices white paper.
EPC devices support three different types of flash memory. Table 1–3 lists the
supported flash memory for all EPC devices.
Table 1–3. Enhanced Configuration Devices Flash Memory (Part 1 of 2)
Flash Memory
Device
EPC4
EPC8
© December 2009
Altera Corporation
Grade
Package
Leaded
Lead-Fee
Commercial
PQFP 100
Intel (1) or Micron
Intel (1) or Micron
Industrial
PQFP 100
Intel (1) or Micron
Intel (1)
Commercial/
Industrial
PQFP 100
Intel (1) or Sharp
Intel (1)
Configuration Handbook (Complete Two-Volume Set)
1–6
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
Table 1–3. Enhanced Configuration Devices Flash Memory (Part 2 of 2)
Flash Memory
Device
EPC16
Grade
Package
Commercial
Leaded
Lead-Fee
UBGA 88
Intel (1) or Sharp
Intel (1) or Sharp
Industrial
UBGA 88
Intel (1) or Sharp
Intel (1)
Commercial/
Industrial
PQFP 100
Intel (1) or Sharp
Intel (1)
Note to Table 1–3:
(1) For more information, refer to the Process Change Notification PCN0506: Addition of Intel Flash Memory As
Source for EPC4, EPC8 and EPC16 Enhanced Configuration Devices.
The external flash interface is currently supported in the EPC16 and EPC4 devices.
For information about using this feature in the EPC8 device, contact Altera Applications at www.altera.com/support.
Enhanced configuration devices have a 3.3-V core and I/O interface. The controller
chip is a synchronous system that implements the various interfaces and features.
Figure 1–1 shows a block diagram of the enhanced configuration device. The
controller chip features three separate interfaces:
■
A configuration interface between the controller and the Altera FPGAs
■
A JTAG interface on the controller that enables ISP of the flash memory
■
An external flash interface that the controller shares with an external processor, or
FPGA implementing a Nios® embedded processor (interface available after ISP
and configuration)
Figure 1–1. Enhanced Configuration Device Block Diagram
JTAG/ISP Interface
Enhanced Configuration Device
Shared Flash
Interface
Flash
Controller
FPGA
Shared Flash Interface
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
1–7
The enhanced configuration device features multiple configuration schemes. In
addition to supporting the traditional passive serial (PS) configuration scheme for a
single device or a serial device chain, the enhanced configuration device features
concurrent configuration and parallel configuration. With the concurrent
configuration scheme, up to eight PS device chains can be configured simultaneously.
In the FPP configuration scheme, 8-bits of data are clocked into the FPGA each cycle.
These schemes offer significantly reduced configuration times over traditional
schemes.
Furthermore, the enhanced configuration device features a dynamic configuration or
page mode feature. This feature allows you to dynamically reconfigure all the FPGAs
in your system with new images stored in the configuration memory. Up to eight
different system configurations or pages can be stored in memory and selected using
the PGM[2..0] pins. Your system can be dynamically reconfigured by selecting one
of the eight pages and initiating a reconfiguration cycle.
This page mode feature combined with the external flash interface allows remote and
local updates of system configuration data. The enhanced configuration devices are
compatible with the Stratix Remote System Configuration feature.
1
For more information about Stratix Remote System Configuration, refer to the Remote
System Configuration with Stratix & Stratix GX Devices chapter in the Stratix Device
Handbook.
Other user programmable features include:
■
Real-time decompression of configuration data
■
Programmable configuration clock (DCLK)
■
Flash ISP
■
Programmable power-on-reset delay (PORSEL)
FPGA Configuration
FPGA configuration is managed by the configuration controller chip. This process
includes reading configuration data from the flash memory, decompressing it if
necessary, transmitting configuration data via the appropriate DATA[] pins, and
handling error conditions.
After POR, the controller determines the user-defined configuration options by
reading its option bits from the flash memory. These options include the configuration
scheme, configuration clock speed, decompression, and configuration page settings.
The option bits are stored at flash address location 0x8000 (word address) and occupy
512-bits or 32-words of memory. These options bits are read using the internal flash
interface and the default 10 MHz internal oscillator.
After obtaining the configuration settings, the configuration controller chip checks if
the FPGA is ready to accept configuration data by monitoring the nSTATUS and
CONF_DONE lines. When the FPGA is ready (nSTATUS is high and CONF_DONE is low),
the controller begins data transfer using the DCLK and DATA[] output pins. The
controller selects the configuration page to be transmitted to the FPGA by sampling
its PGM[2..0] pins after POR or reset.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–8
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
The function of the configuration unit is to transmit decompressed data to the FPGA,
depending on the configuration scheme. The enhanced configuration device supports
four concurrent configuration modes, with n = 1, 2, 4, or 8 (where n is the number of
bits that are sent per DCLK cycle on the DATA[n] lines). The value n = 1 corresponds
to the traditional PS configuration scheme. The values n = 2, 4, and 8 correspond to
concurrent configuration of 2, 4, or 8 different PS configuration chains, respectively.
Additionally, the FPGA can be configured in FPP mode, where eight bits of DATA are
clocked into the FPGA per DCLK cycle. Depending on the configuration bus width (n),
the circuit shifts uncompressed configuration data to the valid DATA[n] pins. Unused
DATA[] pins drive low.
In addition to transmitting configuration data to the FPGAs, the configuration circuit
is also responsible for pausing configuration whenever there is insufficient data
available for transmission. This occurs when the flash read bandwidth is lower than
the configuration write bandwidth. Configuration is paused by stopping the DCLK to
the FPGA, when waiting for data to be read from the flash or for data to be
decompressed. This technique is called “Pausing DCLK”.
The enhanced configuration device flash-memories feature a 90-ns access time
(approximately 10 MHz). Hence, the flash read bandwidth is limited to about 160
megabits per second (Mbps) (16-bit flash data bus, DQ[], at 10 MHz). However, the
configuration speeds supported by Altera FPGAs are much higher and translate to
high configuration write bandwidths. For instance, 100-MHz Stratix FPP
configuration requires data at the rate of 800 Mbps (8-bit DATA[] bus at 100 MHz).
This is much higher than the 160 Mbps the flash memory can support, and is the
limiting factor for configuration time. Compression increases the effective flash-read
bandwidth as the same amount of configuration data takes up less space in the flash
memory after compression. Since Stratix configuration data compression ratios are
approximately two, the effective read bandwidth doubles to about 320 Mbps.
Finally, the configuration controller also manages errors during configuration. A
CONF_DONE error occurs when the FPGA does not de-assert its CONF_DONE signal
within 64 DCLK cycles after the last bit of configuration data is transmitted. When a
CONF_DONE error is detected, the controller pulses the OE line low, which pulls
nSTATUS low and triggers another configuration cycle.
A cyclical redundancy check (CRC) error occurs when the FPGA detects corruption in
the configuration data. This corruption could be a result of noise coupling on the
board such as poor signal integrity on the configuration signals. When this error is
signaled by the FPGA (by driving the nSTATUS line low), the controller stops
configuration. If the Auto-Restart Configuration After Error option is enabled in the
FPGA, it releases its nSTATUS signal after a reset time-out period and the controller
attempts to reconfigure the FPGA.
After the FPGA configuration process is complete, the controller drives DCLK low and
the DATA[] pins high. Additionally, the controller tri-states its internal interface to the
flash memory, enables the weak internal pull-ups on the flash address and control
lines, and enables bus-keep circuits on flash data lines.
The following sections briefly describe the different configuration schemes supported
by the enhanced configuration device: FPP, PS, and concurrent configuration.
f
For detailed information about using these schemes to configure your Altera FPGA,
refer to the appropriate FPGA family chapter in the Configuration Handbook.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
1–9
Configuration Signals
Table 1–4 lists the configuration signal connections between the enhanced
configuration device and Altera FPGAs.
Table 1–4. Configuration Signals
Enhanced
Configuration
Device Pin
Altera FPGA Pin
Description
DATA[]
DATA[]
Configuration data transmitted from the configuration
device to the FPGA, which is latched on the rising edge of
DCLK.
DCLK
DCLK
Configuration device generated clock used by the FPGA to
latch configuration data provided on the DATA[] pins.
nINIT_CONF,
which
nCONFIG
Open-drain output from the configuration device that is
used to start FPGA reconfiguration using the initiate
configuration (INIT_CONF) JTAG instruction. This
connection is not needed if the INIT_CONF JTAG
instruction is not needed. If nINIT_CONF is not
connected to nCONFIG, nCONFIG must be tied to VCC
either directly or through a pull-up resistor.
OE
nSTATUS
Open-drain bidirectional configuration status signal,
which is driven low by either device during POR and to
signal an error during configuration. Low pulse on OE
resets the enhanced configuration device controller.
nCS
CONF_DONE
Configuration done output signal driven by the FPGA.
Fast Passive Parallel Configuration
Stratix series and APEX II devices can be configured using the enhanced
configuration device in FPP mode. In this mode, the enhanced configuration device
sends a byte of data on the DATA[7..0] pins, which connect to the DATA[7..0]
input pins of the FPGA, per DCLK cycle. Stratix series and APEX II FPGAs receive
byte-wide configuration data per DCLK cycle. Figure 1–2 shows the enhanced
configuration device in FPP configuration mode. In this figure, the external flash
interface is not used and hence most flash pins are left unconnected (with the few
noted exceptions). For specific details about configuration interface connections
including pull-up resistor values, supply voltages, and MSEL pin settings, refer to the
appropriate FPGA family chapter in the Configuration Handbook.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–10
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
Figure 1–2. FPP Configuration
Enhanced Configuration
Device
VCC (1) VCC (1)
Stratix Series
or
APEX II Device
n
(6)
MSEL
(3)
WE#C
WE#F
RP#C
RP#F
DCLK
A[20..0]
DATA[7..0]
OE (3)
RY/BY#
nCS (3)
CE#
nINIT_CONF (2)
OE#
(3)
DCLK
DATA[7..0]
nSTATUS
CONF_DONE
nCONFIG
(1) VCC
N.C.
nCEO
N.C.
N.C.
N.C.
N.C.
N.C.
DQ[15..0]
nCE
VCC (7)
WP#
BYTE# (5)
TM1
GND
TMO
VCCW
PORSEL
PGM[2..0]
(4)
(4)
EXCLK
(4)
GND
C-A0 (5)
C-A1 (5)
C-A15 (5)
C-A16 (5)
A0-F
A1-F
A15-F
A16-F
Notes to Figure 1–2:
(1) The VCC should be connected to the same supply voltage as the configuration device.
(2) The nINIT_CONF pin is available on enhanced configuration devices and has an internal pull-up resistor that is always active. This means an
external pull-up resistor is not required on the nINIT_CONF / nCONFIG line. The nINIT_CONF pin does not need to be connected if its
functionality is not used. If nINIT_CONF is not used, nCONFIG must be pulled to VCC either directly or through a resistor.
(3) The enhanced configuration devices’ OE and nCS pins have internal programmable pull-up resistors. If internal pull-up resistors are used, external
pull-up resistors should not be used on these pins. The internal pull-up resistors are used by default in the Quartus® II software. To turn off the
internal pull-up resistors, check the Disable nCS and OE pull-ups on configuration device option when generating programming files.
(4) For PORSEL, PGM[], and EXCLK pin connections, refer to Table 1–10.
(5) In the 100-pin PQFP package, you must externally connect the following pins: C-A0 to F-A0, C-A1 to F-A1, C-A15 to F-A15, C-A16 to
F-A16, and BYTE# to VCC. Additionally, you must make the following pin connections in both 100-pin PQFP and 88-pin UFBGA packages:
C-RP# to F-RP#, C-WE# to F-WE#, TM1 to VCC, TM0 to GND, and WP# to VCC.
(6) Connect the FPGA MSEL[] input pins to select the FPP configuration mode. For details, refer to the appropriate FPGA family chapter in the
Configuration Handbook.
(7) To protect Intel Flash based EPC devices content, isolate the VCCW supply from VCC. For more information, refer section “Intel-Flash-Based EPC
Device Protection” on page 1–15.
Multiple FPGAs can be configured using a single enhanced configuration device in
FPP mode. In this mode, multiple Stratix series FPGAs, APEX II FPGAs, or both, are
cascaded together in a daisy chain.
After the first FPGA completes configuration, its nCEO pin asserts to activate the nCE
pin for the second FPGA, which prompts the second device to start capturing
configuration data. In this setup, the FPGAs CONF_DONE pins are tied together, and
hence all devices initialize and enter user mode simultaneously. If the enhanced
configuration device or one of the FPGAs detects an error, configuration stops (and
simultaneously restarts) for the whole chain because the nSTATUS pins are tied
together.
1
While Altera FPGAs can be cascaded in a configuration chain, the enhanced
configuration devices cannot be cascaded to configure larger devices or chains.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
f
1–11
For configuration schematics and more information about multi-device FPP
configuration, refer to the appropriate FPGA family chapter in the Configuration
Handbook.
Passive Serial Configuration
APEX 20KC, APEX 20KE, APEX 20K, APEX II, Cyclone series, FLEX 10K, and Stratix
series devices can be configured using enhanced configuration devices in the PS
mode. This mode is similar to the FPP mode, with the exception that only one bit of
data (DATA[0]) is transmitted to the FPGA per DCLK cycle. The remaining
DATA[7..1] output pins are unused in this mode and drive low.
The configuration schematic for PS configuration of a single FPGA or single serial
chain is identical to the FPP schematic (with the exception that only DATA[0] output
from the enhanced configuration device connects to the FPGA DATA0 input pin;
remaining DATA[7..1] pins are left floating).
f
For configuration schematics and more information about multi-device PS
configuration, refer to the appropriate FPGA family chapter in the Configuration
Handbook.
Concurrent Configuration
Enhanced configuration devices support concurrent configuration of multiple FPGAs
(or FPGA chains) in PS mode. Concurrent configuration is when the enhanced
configuration device simultaneously outputs n bits of configuration data on the
DATA[n-1..0] pins (n = 1, 2, 4, or 8), and each DATA[] line serially configures a
different FPGA (chain). The number of concurrent serial chains is user-defined via the
Quartus II software and can be any number from 1 to 8. For example, three concurrent
chains you can select the 4-bit PS mode, and connect the least significant DATA bits to
the FPGAs or FPGA chains. Leave the most significant DATA bit (DATA[3])
unconnected. Similarly, for 5-, 6-, or 7-bit concurrent chains you can select the 8-bit PS
mode.
Figure 1–3 shows the schematic for configuring multiple FPGAs concurrently in the
PS mode using an enhanced configuration device.
f
© December 2009
For specific details about configuration interface connections including pull-up
resistor values, supply voltages, and MSEL pin settings, refer to the appropriate FPGA
family chapter in the Configuration Handbook.
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–12
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
Figure 1–3. Concurrent Configuration of Multiple FPGAs in PS Mode (n = 8)
VCC (1)
(3)
FPGA0
WE#C
RP#C
DCLK
DATA0
(3)
DCLK
DATA0
n
(6)
Enhanced Configuration
Device
VCC (1)
MSEL
nSTATUS
CONF_DONE
nCONFIG
DATA1
nCE
N.C.
n
MSEL
DQ[15..0]
N.C.
VCCW
DCLK
DATA0
nSTATUS
CONF_DONE
nCONFIG
WP#
BYTE# (5)
TM1
PORSEL
PGM[2..0]
(4)
(4)
EXCLK
(4)
TMO
GND
nCE
N.C.
N.C.
N.C.
VCC (7)
FPGA7
MSEL
CE#
OE#
(1)
VCC
nCEO
n
N.C.
DATA 7
GND
(6)
N.C.
RY/BY#
nINIT_CONF (2)
GND
DCLK
DATA0
nSTATUS
CONF_DONE
nCONFIG
nCE
N.C.
RP#F
A[20..0]
nCS (3)
FPGA1
(6)
OE (3)
nCEO
WE#F
nCEO
GND
C-A0 (5)
C-A1 (5)
C-A15 (5)
C-A16 (5)
A0-F
A1-F
A15-F
A16-F
Notes to Figure 1–3:
(1) Connect VCC to the same supply voltage as the configuration device.
(2) The nINIT_CONF pin is available on enhanced configuration devices and has an internal pull-up resistor that is always active. This means an
external pull-up resistor is not required on the nINIT_CONF/nCONFIG line. The nINIT_CONF pin does not need to be connected if its
functionality is not used. If nINIT_CONF is not used, nCONFIG must be pulled to VCC either directly or through a resistor.
(3) The enhanced configuration devices’ OE and nCS pins have internal programmable pull-up resistors. If internal pull-up resistors are used, external
pull-up resistors should not be used on these pins. The internal pull-up resistors are used by default in the Quartus II software. To turn off the
internal pull-up resistors, check the Disable nCS and OE pull-ups on configuration device option when generating programming files.
(4) For PORSEL, PGM[], and EXCLK pin connections, refer to Table 1–10.
(5) In the 100-pin PQFP package, you must externally connect the following pins: C-A0 to F-A0, C-A1 to F-A1, C-A15 to F-A15, C-A16 to
F-A16, and BYTE# to VCC. Additionally, you must make the following pin connections in both 100-pin PQFP and 88-pin UFBGA packages:
C-RP# to F-RP#, C-WE# to F-WE#, TM1 to VCC, TM0 to GND, and WP# to VCC.
(6) Connect the FPGA MSEL[] input pins to select the PS configuration mode. For details, refer to the appropriate FPGA family chapter in the
Configuration Handbook.
(7) To protect Intel Flash based EPC devices content, isolate the VCCW supply from VCC. For more information, refer section “Intel-Flash-Based EPC
Device Protection” on page 1–15.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
1–13
Table 1–5 summarizes the concurrent PS configuration modes supported in the
enhanced configuration device.
Table 1–5. Enhanced Configuration Devices in PS Mode
Mode Name
Mode (n =) (1)
Used Outputs
Unused Outputs
Passive serial mode
1
DATA0
DATA[7..1] drive low
Multi-device passive
serial mode
2
DATA[1..0]
DATA[7..2] drive low
Multi-device passive
serial mode
4
DATA[3..0]
DATA[7..4] drive low
Multi-device passive
serial mode
8
DATA[7..0]
—
Note to Table 1–5:
(1) This is the number of valid DATA outputs for each configuration mode.
f
For configuration schematics and more information about concurrent configurations,
refer to the appropriate FPGA family chapter in the Configuration Handbook.
External Flash Interface
The enhanced configuration devices support external FPGA or processor access to its
flash memory. The unused portions of the flash memory can be used by the external
device to store code or data. This interface can also be used in systems that implement
remote configuration capabilities. Configuration data within a particular
configuration page can be updated via the external flash interface and the system
could be reconfigured with the new FPGA image. This interface is also useful to store
Nios boot code, application code, or both.
f
For more information about the Stratix remote configuration feature, refer to the
Remote System Configuration with Stratix & Stratix GX Devices chapter in the Stratix
Device Handbook.
The address, data, and control ports of the flash memory are internally connected to
the enhanced configuration device controller and to external device pins. An external
source can drive these external device pins to access the flash memory when the flash
interface is available.
This external flash interface is a shared bus interface with the configuration controller
chip. The configuration controller is the primary bus master. Since there is no bus
arbitration support, the external device can only access the flash interface when the
controller has tri-stated its internal interface to the flash. Simultaneous access by the
controller and the external device will cause contention, and result in configuration
and programming failures.
Since the internal flash interface is directly connected to the external flash interface
pins, controller flash access cycles will toggle the external flash interface pins. The
external device must be able to tri-state its flash interface during these operations and
ignore transitions on the flash interface pins.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–14
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
1
The external flash interface signals cannot be shared between multiple enhanced
configuration devices because this causes contention during in-system programming
and configuration. During these operations, the controller chips inside the enhanced
configuration devices are actively accessing flash memory. Therefore, enhanced
configuration devices do not support shared flash bus interfaces.
The enhanced configuration device controller chip accesses flash memory during:
■
FPGA configuration—reading configuration data from flash
■
JTAG-based flash programming—storing configuration data in flash
■
At POR—reading option bits from flash
During these operations, the external FPGA or processor must tri-state its interface to
the flash memory. After configuration and programming, the enhanced configuration
device’s controller tri-states the internal interface and goes into an idle mode. To
interrupt a configuration cycle in order to access the flash via the external flash
interface, the external device can hold the FPGA’s nCONFIG input low. This keeps the
configuration device in reset by holding the nSTATUS-OE line low, allowing external
flash access.
f
For more information about the software support for the external flash interface
feature, refer to the Altera Enhanced Configuration Devices chapter in volume 2 of the
Configuration Handbook. For details about flash commands, timing, memory
organization, and write protection features, refer to the following documents:
■
For Micron flash-based EPC4, refer to the Micron Flash Memory MT28F400B3 Data
Sheet at www.micron.com.
■
For Sharp flash-based EPC16, refer to the Sharp LHF16J06 Data Sheet Flash Memory
Used in EPC16 Devices at www.sharpsma.com.
■
For the Intel Advanced Boot Block Flash Memory (B3) 28F008/800B3, 28F016/160B3,
28F320B3, 28F640B3 Datasheet, visit www.intel.com.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
1–15
Figure 1–4 shows an FPP configuration schematic with the external flash interface in
use.
Figure 1–4. FPP Configuration with External Flash Interface (Note 1)
VCC
Enhanced Configuration
Device
VCC
Stratix Series
or
APEX II Device
n
MSEL
N.C.
PLD or Processor
WE#C
WE#F
RP#C
RP#F
DCLK
DATA[7..0] A[20..0] (2)
OE
RY/BY# (5)
nCS
CE#
nINIT_CONF
OE#
DCLK
DATA[7..0]
nSTATUS
CONF_DONE
nCONFIG
nCEO
WE#
RP#
A[20..0]
RY/BY#
CE#
OE#
DQ[15..0]
nCE
DQ[15..0]
VCC
VCC(6)
WP#
BYTE# (3)
TM1
GND
TMO
VCCW
PORSEL
PGM[2..0]
(4)
(4)
EXCLK
(4)
GND
C-A0 (3)
C-A1 (3)
C-A15 (3)
C-A16 (3)
A0-F
A1-F
A15-F
A16-F
Notes to Figure 1–4:
(1) For external flash interface support in EPC8 enhanced configuration device, contact Altera Applications.
(2) Pin A20 in EPC16 devices, pins A20 and A19 in EPC8 devices, and pins A20, A19, and A18 in EPC4 devices should be left floating. These pins
should not be connected to any signal; they are no-connect pins.
(3) In the 100-pin PQFP package, you must externally connect the following pins: C-A0 to F-A0, C-A1 to F-A1, C-A15 to F-A15, C-A16 to
F-A16, and BYTE# to VCC. Additionally, you must make the following pin connections in both 100-pin PQFP and 88-pin UFBGA packages:
C-RP# to F-RP#, C-WE# to F-WE#, TM1 to VCC, TM0 to GND, and WP# to VCC.
(4) For PORSEL, PGM[], and EXCLK pin connections, refer to Table 1–10.
(5) RY/BY# pin is only available for Sharp flash-based EPC8 and EPC16.
(6) To protect Intel Flash based EPC devices content, isolate the VCCW supply from VCC. For more information, refer section “Intel-Flash-Based EPC
Device Protection” on page 1–15.
Intel-Flash-Based EPC Device Protection
In the absence of the lock bit protection feature in the EPC4, EPC8, and EPC16 devices
with Intel flash, Altera recommends four methods to protect the Intel Flash content in
EPC4, EPC8, and EPC16 devices. Any method alone is sufficient to protect the flash.
The methods are listed here in the order of descending protection level:
1. Using an RP# of less than 0.3 V on power-up and power-down for a minimum of
100 ns to a maximum 25 ms disables all control pins, making it impossible for a
write to occur.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–16
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
2. Using VPP < VPPLK, where the maximum value of VPPLK is 1 V, disables writes.
VPP < VPPLK means programming or writes cannot occur. VPP is a programming
supply voltage input pin on the Intel flash. VPP is equivalent to the VCCW pin on
EPC devices.
3. Using a high CE# disables the chip. The requirement for a write is a low CE# and
low WE#. A high CE# by itself prevents writes from occurring.
4. Using a high WE# prevent writes because a write only occurs when the WE# is low.
Performing all four methods simultaneously is the safest protection for the flash
content.
The ideal power-up sequence is as follows:
1. Power-up VCC .
2. Maintain VPP < VPPLK until VCC is fully powered up.
3. Power-up VPP .
4. Drive RP# low during the entire power-up process. RP# must be released high
within 25 ms after VPP is powered up.
1
CE# and WE# must be high for the entire power-up sequence.
The ideal power-down sequence is as follows:
1. Drive RP# low for 100ns before power-down.
2. Power-down VPP < VPPLK.
3. Power-down VCC.
4. Drive RP# low during the entire power-down process.
1
CE# and WE# must be high for the entire power-down sequence.
The RP# pin is not internally connected to the controller. Therefore, an external
loop-back connection between C-RP# and F-RP# must be made on the board even
when you are not using the external device to the RP# pin with the loop-back. Always
tri-state RP# when the flash is not in use.
If an external power-up monitoring circuit is connected to the RP# pin with the
loop-back, use the following guidelines to avoid contention on the RP# line:
■
The power-up sequence on the 3.3-V supply should complete within 50 ms of
power-up. The 3.3-V VCC should reach the minimum VCC before 50 ms and RP#
should then be released.
■
RP# should be driven low by the power-up monitoring circuit during power-up.
After power-up, RP# should be tri-stated externally by the power-up monitoring
circuit.
If the preceding guidelines cannot be completed within 50 ms, then the OE pin must
be driven low externally until RP# is ready to be released.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
1–17
Dynamic Configuration (Page Mode)
The dynamic configuration (or page mode) feature allows the enhanced configuration
device to store up to eight different sets of designs for all the FPGAs in your system.
You can then choose which page (set of configuration files) the enhanced
configuration device should use for FPGA configuration.
Dynamic configuration or the page mode feature enables you to store a minimum of
two pages: a factory default or fail-safe configuration, and an application
configuration. The fail-safe configuration page could be programmed during system
production, while the application configuration page could support remote or local
updates. These remote updates could add or enhance system features and
performance. However, with remote update capabilities comes the risk of possible
corruption of configuration data. In the event of such a corruption, the system could
automatically switch to the fail-safe configuration and avoid system downtime.
The enhanced configuration device page mode feature works with the Stratix Remote
System Configuration feature, to enable intelligent remote updates to your systems.
f
For more information about remotely updating Stratix FPGAs, refer to Remote System
Configuration with Stratix & Stratix GX Devices in the Stratix Device Handbook.
The three PGM[2..0] input pins control which page is used for configuration, and
these pins are sampled at the start of each configuration cycle when OE goes high. The
page mode selection allows you to dynamically reconfigure the functionality of your
FPGA by switching the PGM[2..0] pins and asserting nCONFIG. Page 0 is defined as
the default page and the PGM[2] pin is the most significant bit (MSB).
1
The PGM[2..0] input pins must not be left floating on your board, regardless of
whether this feature is used or not. When this feature is not used, connect the
PGM[2..0] pins to GND to select the default page 000.
The enhanced configuration device pages are dynamically sized regions in memory.
The start address and length of each page is programmed into the option-bit space of
the flash memory during initial programming. All subsequent configuration cycles
will sample the PGM[] pins and use the option-bit information to jump to the start of
the corresponding configuration page. Each page must have configuration files for all
FPGAs in your system that are connected to that enhanced configuration device.
For example, if your system requires three configuration pages and includes two
FPGAs, each page will store two SRAM Object Files (.sof) for a total of six .sof in the
configuration device.
Furthermore, all enhanced configuration device configuration schemes (PS, FPP, and
concurrent PS) are supported with the page-mode feature. The number of pages,
devices, or both, that can be configured using a single enhanced configuration device
is only limited by the size of the flash memory.
f
© December 2009
For detailed information about the page-mode feature implementation and
programming file generation steps using the Quartus II software, refer to the Altera
Enhanced Configuration Devices chapter in volume 2 of the Configuration Handbook.
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–18
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
Real-Time Decompression
Enhanced configuration devices support on-chip real time decompression of
configuration data. FPGA configuration data is compressed by the Quartus II
software and stored in the enhanced configuration device. During configuration, the
decompression engine inside the enhanced configuration device will decompress or
expand configuration data. This feature increases the effective-configuration density
of the enhanced configuration device up to 7, 15, or 30 Mbits in the EPC4, EPC8, and
EPC16, respectively.
The enhanced configuration device also supports a parallel 8-bit data bus to the FPGA
to reduce configuration time. However, in some cases, the FPGA data-transfer time is
limited by the flash-read bandwidth. For example, when configuring an APEX II
device in FPP (byte-wide data per cycle) mode at a configuration speed of 66 MHz,
the FPGA write bandwidth is equal to 8 bits × 66 MHz = 528 Mbps. The flash read
interface, however, is limited to approximately 10 MHz (since the flash access time is
~90 ns). This translates to a flash-read bandwidth of
16 bits × 10 MHz = 160 Mbps. Hence, the configuration time is limited by the
flash-read time.
When configuration data is compressed, the amount of data that needs to be read out
of the flash is reduced by about 50%. If 16 bits of compressed data yields 30 bits of
uncompressed data, the flash-read bandwidth increases to 30 bits × 10 MHz =
300 Mbps, reducing overall configuration time.
You can enable the controller's decompression feature in the Quartus II software,
Configuration Device Options window by turning on Compression Mode.
1
The decompression feature supported in the enhanced configuration devices is
different from the decompression feature supported by the Stratix II FPGAs and the
Cyclone series. When configuring Stratix II FPGAs or the Cyclone series using
enhanced configuration devices, Altera recommends enabling decompression in
Stratix II FPGAS or the Cyclone series only for faster configuration.
The compression algorithm used in Altera devices is optimized for FPGA
configuration bitstreams. Since FPGAs have several layers of routing structures (for
high performance and easy routability), large amounts of resources go unused. These
unused routing and logic resources as well as un-initialized memory structures result
in a large number of configuration RAM bits in the disabled state. Altera's proprietary
compression algorithm takes advantage of such bitstream qualities.
The general guideline for effectiveness of compression is the higher the device
logic/routing utilization, the lower the compression ratio (where the compression
ratio is defined as the original bitstream size divided by the compressed bitstream
size).
For Stratix designs, based on a suite of designs with varying amounts of logic
utilization, the minimum compression ratio was observed to be 1.9 or a ~47% size
reduction for these designs. Table 1–6 lists sample compression ratios from a suite of
Stratix designs. These numbers serve as a guideline (not a specification) to help you
allocate sufficient configuration memory to store compressed bitstreams.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
1–19
Table 1–6. Stratix Compression Ratios (Note 1)
Item
Minimum
Average
Logic Utilization
98%
64%
Compression Ratio
1.9
2.3
% Size Reduction
47%
57%
Note to Table 1–6:
(1) These numbers are preliminary. They are intended to serve as a guideline, not a specification.
Programmable Configuration Clock
The configuration clock (DCLK) speed is user programmable. One of two clock sources
can be used to synthesize the configuration clock; a programmable oscillator or an
external clock input pin (EXCLK). The configuration clock frequency can be further
synthesized using the clock divider circuitry. This clock can be divided by the N
counter to generate your DCLK output. The N divider supports all integer dividers
between 1 and 16, as well as a 1.5 divider and a 2.5 divider. The duty cycle for all clock
divisions other than non-integer divisions is 50% (for the non-integer dividers, the
duty cycle will not be 50%). Refer to Figure 1–5 for a block diagram of the clock
divider unit.
Figure 1–5. Clock Divider Unit
Configuration Device
Clock Divider Unit
External Clock
(Up to 100 MHz)
10 MHz
33 MHz
50 MHz
66 MHz
Divide
by N
DCLK
Internal Oscillator
The DCLK frequency is limited by the maximum DCLK frequency the FPGA supports.
f
© December 2009
The maximum DCLK input frequency supported by the FGPA is specified in the
appropriate FPGA family chapter in the Configuration Handbook.
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–20
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Functional Description
The controller chip features a programmable oscillator that can output four different
frequencies. The various settings generate clock outputs at frequencies as high as 10,
33, 50, and 66 MHz, as listed in Table 1–7.
Table 1–7. Internal Oscillator Frequencies
Frequency Setting
Min (MHz)
Typ (MHz)
Max (MHz)
10
6.4
8.0
10.0
33
21.0
26.5
33.0
50
32.0
40.0
50.0
66
42.0
53.0
66.0
Clock source, oscillator frequency, and clock divider (N) settings can be made in the
Quartus II software, by accessing the Configuration Device Options inside the
Device Settings window or the Convert Programming Files window. The same
window can be used to select between the internal oscillator and the external clock
(EXCLK) input pin as your configuration clock source. The default setting selects the
internal oscillator at the 10 MHz setting as the clock source, with a divide factor of 1.
f
For more information about making the configuration clock source, frequency, and
divider settings, refer to the Altera Enhanced Configuration Devices chapter in volume 2
of the Configuration Handbook.
Flash In-System Programming (ISP)
The flash memory inside enhanced configuration devices can be programmed
in-system via the JTAG interface and the external flash interface. JTAG-based
programming is facilitated by the configuration controller in the enhanced
configuration device. External flash interface programming requires an external
processor or FPGA to control the flash.
1
The enhanced configuration device flash memory supports 100,000 erase cycles.
JTAG-based Programming
The IEEE Std. 1149.1 JTAG Boundary Scan is implemented in enhanced configuration
devices to facilitate the testing of its interconnection and functionality. Enhanced
configuration devices also support the ISP mode. The enhanced configuration device
is compliant with the IEEE Std. 1532 draft 2.0 specification.
The JTAG unit of the configuration controller communicates directly with the flash
memory. The controller processes the ISP instructions and performs the necessary
flash operations. The enhanced configuration devices support a maximum JTAG TCK
frequency of 10 MHz.
During JTAG-based ISP, the external flash interface is not available. Before the JTAG
interface programs the flash memory, an optional JTAG instruction (PENDCFG) can be
used to assert the FPGA’s nCONFIG pin (via the nINIT_CONF pin). This will keep the
FPGA in reset and terminate any internal flash access. This function prevents
contention on the flash pins when both JTAG ISP and an external FPGA or processor
try to access the flash simultaneously. The nINIT_CONF pin is released when the
initiate configuration (nINIT_CONF) JTAG instruction is updated. As a result, the
FPGA is configured with the new configuration data stored in flash.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Pin Description
1–21
An initiate configuration (nINIT_CONF) JTAG instruction can be added to your
programming file in the Quartus II software by enabling the Initiate configuration
after programming option in the Programmer options window (Options menu).
Programming via External Flash Interface
This method allows parallel programming of the flash memory (using the 16-bit data
bus). An external processor or FPGA acts as the flash controller and has access to
programming data (via a communication link such as UART, Ethernet, and PCI). In
addition to the program, erase, and verify operations, the external flash interface
supports block/sector protection instructions.
f
For information about protection commands, areas, and lock bits, refer to the
appropriate flash data sheets.
■
For Micron flash-based EPC4, refer to the Micron Flash Memory MT28F400B3 Data
Sheet at www.micron.com.
■
For Sharp flash-based EPC16, refer to the Sharp LHF16J06 Data Sheet Flash Memory
Used in EPC16 Devices at www.sharpsma.com.
■
For the Intel Advanced Boot Block Flash Memory (B3) 28F008/800B3, 28F016/160B3,
28F320B3, 28F640B3 Datasheet, visit www.intel.com.
External flash interface programming is only allowed when the configuration
controller has relinquished flash access (by tri-stating its internal interface). If the
controller has not relinquished flash access (during configuration or JTAG-based ISP),
you must hold the controller in reset before initiating external programming. The
controller can be reset by holding the FPGA nCONFIG line at a logic low level. This
keeps the controller in reset by holding the nSTATUS-OE line low, allowing external
flash access.
1
If initial programming of the enhanced configuration device is done in-system via the
external flash interface, the controller must be kept in reset by driving the FPGA
nCONFIG line low to prevent contention on the flash interface.
Pin Description
Table 1–8 through Table 1–10 describe the enhanced configuration device pins. These
tables include configuration interface pins, external flash interface pins, JTAG
interface pins, and other pins.
Table 1–8. Configuration Interface Pins (Part 1 of 2)
Pin Name
Pin Type
Description
DATA[7..0]
Output
Configuration data output bus. DATA changes on each falling edge of DCLK.
DATA is latched into the FPGA on the rising edge of DCLK.
DCLK
Output
The DCLK output pin from the enhanced configuration device serves as the FPGA
configuration clock. DATA is latched by the FPGA on the rising edge of DCLK.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–22
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Pin Description
Table 1–8. Configuration Interface Pins (Part 2 of 2)
Pin Name
nCS
nINIT_CONF
OE
Pin Type
Description
Input
The nCS pin is an input to the enhanced configuration device and is connected to
the FPGA’s CONF_DONE signal for error detection after all configuration data is
transmitted to the FPGA. The FPGA will always drive nCS and OE low when
nCONFIG is asserted. This pin contains a programmable internal weak pull-up
resistor of 6K  that can be disabled/enabled in the Quartus II software through
the Disable nCS and OE pull-ups on configuration device option.
Open-Drain Output
The nINIT_CONF pin can be connected to the nCONFIG pin on the FPGA to
initiate configuration from the enhanced configuration device via a private JTAG
instruction. This pin contains an internal weak pull-up resistor of 6K that is
always active. The INIT_CONF pin does not need to be connected if its
functionality is not used. If nINIT_CONF is not used, nCONFIG must be pulled
to VCC either directly or through a pull-up resistor.
Open-Drain
Bidirectional
This pin is driven low when POR is not complete. A user-selectable 2-ms or
100-ms counter holds off the release of OE during initial power up to permit
voltage levels to stabilize. POR time can be extended by externally holding OE
low. OE is connected to the FPGA nSTATUS signal. After the enhanced
configuration device controller releases OE, it waits for the nSTATUS-OE line to
go high before starting the FPGA configuration process. This pin contains a
programmable internal weak pull-up resistor of 6K that can be
disabled/enabled in the Quartus II software through the Disable nCS and OE
pull-ups on configuration device option.
Table 1–9. External Flash Interface Pins (Part 1 of 3)
Pin Name
A[20..0]
Pin Type
Input
Description
These pins are the address input to the flash memory for read and write
operations. The addresses are internally latched during a write cycle.
When the external flash interface is not used, leave these pins floating (with a few
exceptions(1)). These flash address, data, and control pins are internally
connected to the configuration controller.
In the 100-pin PQFP package, four address pins (A0, A1, A15, A16) are not
internally connected to the controller. These loop-back connections must be made
on the board between the C-A[] and F-A[] pins even when not using the
external flash interface. All other address pins are connected internal to the
package.
All address pins are connected internally in the 88-pin UFBGA package.
Pin A20 in EPC16 devices, pins A20 and A19 in EPC8 devices, and pins A20,
A19, and A18 in EPC4 devices are no-connects. These pins should be left
floating on the board.
DQ[15..0]
Bidirectional
This is the flash data bus interface between the flash memory and the controller.
The controller or an external source drives DQ[15..0] during the flash
command and the data write bus cycles. During the data read cycle, the flash
memory drives the DQ[15..0] to the controller or external device.
Leave these pins floating on the board when the external flash interface is not
used.
CE#
Input
Active low flash input pin that activates the flash memory when asserted. When it
is high, it deselects the device and reduces power consumption to standby levels.
This flash input pin is internally connected to the controller.
Leave this pin floating on the board when the external flash interface is not used.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Pin Description
1–23
Table 1–9. External Flash Interface Pins (Part 2 of 3)
Pin Name
RP# (1)
Pin Type
Input
Description
Active low flash input pin that resets the flash when asserted. When high, it
enables normal operation. When low, it inhibits write operation to the flash
memory, which provides data protection during power transitions.
This flash input is not internally connected to the controller. Hence, an external
loop-back connection between C-RP# and F-RP# must be made on the board
even when you are not using the external flash interface.
When using the external flash interface, connect the external device to the RP#
pin with the loop back. Always tri-state RP# when the flash is not in use.
OE#
Input
Active-low flash-control input that is asserted by the controller or external device
during flash read cycles. When asserted, it enables the drivers of the flash output
pins.
Leave this pin floating on the board when the external flash interface is not used.
WE# (1)
Input
Active-low flash-write strobe asserted by the controller or external device during
flash write cycles. When asserted, it controls writes to the flash memory. In the
flash memory, addresses and data are latched on the rising edge of the WE#
pulse.
This flash input is not internally connected to the controller. Hence, an external
loop-back connection between C-WE# and F-WE# must be made on the board
even when you are not using the external flash interface.
When using the external flash interface, connect the external device to the WE#
pin with the loop back.
WP#
Input
Usually tied to VCC or ground on the board. The controller does not drive this pin
because it could cause contention.
Connection to VCC is recommended for faster block erase/programming times and
to allow programming of the flash-bottom boot block, which is required when
programming the device using the Quartus II software.
This pin should be connected to VCC even when the external flash interface is not
used.
VCCW
Supply
Block erase, full-chip erase, word write, or lock-bit configuration power supply.
Connect this pin to the 3.3-V VCC supply, even when you are not using the external
flash interface.
RY/BY#
Open-Drain Output
Flash asserts this pin when a write or erase operation is complete. This pin is not
connected to the controller. RY/BY# is only available in Sharp flash-based EPC8
and EPC16. (2)
Leave this pin floating when the external flash interface is not used.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–24
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Pin Description
Table 1–9. External Flash Interface Pins (Part 3 of 3)
Pin Name
BYTE#
Pin Type
Description
Input
Flash byte-enable pin and is only available for enhanced configuration devices in
the 100-pin PQFP package.
This pin must be connected to VCC on the board even when you are not using the
external flash interface (the controller uses the flash in 16-bit mode). For Intel
flash-based EPC device, this pin is connected to the VCCQ of the Intel flash die
internally. Therefore, BYTE# must be connected directly to VCC without using any
pull-up resistor.
Notes to Table 1–9:
(1) These pins can be driven to 12 V during production testing of the flash memory. Since the controller cannot tolerate the 12-V level, connections
from the controller to these pins are not made internal to the package. Instead they are available as two separate pins. You must connect the
two pins at the board level (for example, on the printed circuit board (PCB), connect the C-WE# pin from controller to F-WE# pin from the
flash memory).
(2) For more information, refer to the Process Change Notification PCN0506: Addition of Intel Flash Memory As Source For EPC4, EPC8 and EPC16
Enhanced Configuration Devices and Using the Intel Flash Memory-Based EPC4, EPC8 and EPC16 white paper.
Table 1–10. JTAG Interface Pins and Other Required Controller Pins
Pin Name
TDI
Pin Type
Input
Description
JTAG data input pin.
Connect this pin to VCC if the JTAG circuitry is not used.
TDO
Output
JTAG data output pin.
Do not connect this pin if the JTAG circuitry is not used (leave floating).
TCK
Input
JTAG clock pin.
Connect this pin to GND if the JTAG circuitry is not used.
TMS
Input
JTAG mode select pin.
Connect this pin to VCC if the JTAG circuitry is not used.
PGM[2..0]
Input
These three input pins select one of the eight pages of configuration data to
configure the FPGAs in the system.
Connect these pins on the board to select the page specified in the Quartus II
software when generating the enhanced configuration device POF. PGM[2] is the
MSB. The default selection is page 0; PGM[2..0]=000. These pins must not be
left floating.
EXCLK
Input
Optional external clock input pin that can be used to generate the configuration
clock (DCLK).
When an external clock source is not used, connect this pin to a valid logic level
(high or low) to prevent a floating-input buffer. If EXCLK is used, toggling the
EXCLK input pin after the FPGA enters user mode will not effect the enhanced
configuration device operation.
PORSEL
Input
This pin selects a 2-ms or 100-ms POR counter delay during power up. When
PORSEL is low, POR time is 100 ms. When PORSEL is high, POR time is 2 ms.
TM0
Input
For normal operation, this test pin must be connected to GND.
TM1
Input
For normal operating, this test pin must be connected to VCC.
This pin must be connected to a valid logic level.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Power-On Reset
1–25
Power-On Reset
The POR circuit keeps the system in reset until power-supply voltage levels have
stabilized. The POR time consists of the VCC ramp time and a user-programmable
POR delay counter. When the supply is stable and the POR counter expires, the POR
circuit releases the OE pin. The POR time can be further extended by an external
device by driving the OE pin low.
1
Do not execute JTAG or ISP instructions until POR is complete.
The enhanced configuration device supports a programmable POR delay setting. You
can set the POR delay to the default 100-ms setting or reduce the POR delay to 2 ms
for systems that require fast power-up. The PORSEL input pin controls this POR
delay; a logic-high level selects the 2-ms delay, while a logic-low level selects the
100-ms delay.
The enhanced configuration device can enter reset under the following conditions:
■
The POR reset starts at initial power-up during VCC ramp-up or if VCC drops
below the minimum operating condition anytime after VCC has stabilized
■
The FPGA initiates reconfiguration by driving nSTATUS low, which occurs if the
FPGA detects a CRC error or if the FPGA’s nCONFIG input pin is asserted
■
The controller detects a configuration error and asserts OE to begin
re-configuration of the Altera FPGA (for example, when CONF_DONE stays low
after all configuration data has been transmitted)
Power Sequencing
Altera requires that you power-up the FPGA's VCCINT supply before the enhanced
configuration device's POR expires.
Power up needs to be controlled so that the enhanced configuration device’s OE signal
goes high after the CONF_DONE signal is pulled low. If the EEPC device exits POR
before the FPGA is powered up, the CONF_DONE signal will be high because the
pull-up resistor is holding this signal high. When the enhanced configuration device
exits POR, OE is released and pulled high by a pull-up resistor. Since the enhanced
configuration device samples the nCS signal on the rising edge of OE, it detects a high
level on CONF_DONE and enters an idle mode. DATA and DCLK outputs will not toggle
in this state and configuration will not begin. The enhanced configuration device will
only exit this mode if it is powered down and then powered up correctly.
1
To ensure the enhanced configuration device enters configuration mode properly, you
must ensure that the FPGA completes power-up before the enhanced configuration
device exits POR.
The pin-selectable POR time feature is useful for ensuring this power-up sequence.
The enhanced configuration device has two POR settings, 2 ms when PORSEL is set to
a high level and 100 ms when PORSEL is set to a low level. For more margin, the
100-ms setting can be selected to allow the FPGA to power-up before configuration is
attempted.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–26
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Programming and Configuration File Support
Alternatively, a power-monitoring circuit or a power-good signal can be used to keep
the FPGA’s nCONFIG pin asserted low until both supplies have stabilized. This
ensures the correct power up sequence for successful configuration.
Programming and Configuration File Support
The Quartus II software provides programming support for the enhanced
configuration device and automatically generates the .pof for the EPC4, EPC8, and
EPC16 devices. In a multi-device project, the software can combine the .sof for
multiple ACEX 1K, APEX 20K, APEX II, Cyclone series, FLEX 10K, Mercury, and
Stratix series FPGAs into one programming file for the enhanced configuration
device.
f
For details about generating programming files, refer to the Altera Enhanced
Configuration Devices chapter and the Software Settings section in volume 2 of the
Configuration Handbook.
Enhanced configuration devices can be programmed in-system through the
industry-standard 4-pin JTAG interface. The ISP feature in the enhanced
configuration device provides ease in prototyping and updating FPGA functionality.
After programming an enhanced configuration device in-system, FPGA configuration
can be initiated by including the enhanced configuration device’s JTAG INIT_CONF
instruction (Table 1–11).
The ISP circuitry in the enhanced configuration device is compliant with the IEEE Std.
1532 specification. The IEEE Std. 1532 is a standard that allows concurrent ISP
between devices from multiple vendors.
Table 1–11. Enhanced Configuration Device JTAG Instructions (Part 1 of 2) (Note 1)
JTAG Instruction
OPCODE
Description
SAMPLE/
PRELOAD
00 0101 0101
Allows a snapshot of the state of the enhanced configuration device pins to be
captured and examined during normal device operation and permits an initial
data pattern output at the device pins.
EXTEST
00 0000 0000
Allows the external circuitry and board-level interconnections to be tested by
forcing a test pattern at the output pins and capturing results at the input pins.
BYPASS
11 1111 1111
Places the 1-bit bypass register between the TDI and the TDO pins, which allow
the BST data to pass synchronously through a selected device to adjacent
devices during normal device operation.
IDCODE
00 0101 1001
Selects the device IDCODE register and places it between TDI and TDO,
allowing the device IDCODE to be serially shifted out to TDO. The device
IDCODE for all enhanced configuration devices is the same and shown below:
0100A0DDh
USERCODE
00 0111 1001
Selects the USERCODE register and places it between TDI and TDO, allowing
the USERCODE to be serially shifted out the TDO. The 32-bit USERCODE is a
programmable user-defined pattern.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Programming and Configuration File Support
1–27
Table 1–11. Enhanced Configuration Device JTAG Instructions (Part 2 of 2) (Note 1)
JTAG Instruction
OPCODE
Description
INIT_CONF
00 0110 0001
This function initiates the FPGA re-configuration process by pulsing the
nINIT_CONF pin low, which is connected to the FPGA nCONFIG pin. After
this instruction is updated, the nINIT_CONF pin is pulsed low when the JTAG
state machine enters Run-Test/Idle state. The nINIT_CONF pin is then
released and nCONFIG is pulled high by the resistor after the JTAG state
machine goes out of Run-Test/Idle state. The FPGA configuration starts after
nCONFIG goes high. As a result, the FPGA is configured with the new
configuration data stored in flash via ISP. This function can be added to your
programming file (.pof, .jam, .jbc) in the Quartus II software by enabling the
Initiate configuration after programming option in the Programmer options
window (Options menu).
PENDCFG
00 0110 0101
This optional function can be used to hold the nINIT_CONF pin low during
JTAG-based ISP of the enhanced configuration device. This feature is useful
when the external flash interface is controlled by an external FPGA/processor.
This function prevents contention on the flash pins when both the controller and
external device try to access the flash simultaneously. Before the enhanced
configuration device’s controller can access the flash memory, the external
FPGA/processor needs to tri-state its interface to flash.This can be ensured by
resetting the FPGA using the nINIT_CONF, which drives the nCONFIG pin and
keeps the external FPGA/processor in the “reset” state. The nINIT_CONF pin is
released when the initiate configuration (INIT_CONF) JTAG instruction is
issued.
Note to Table 1–11:
(1) Enhanced configuration device instruction register length is 10 and boundary scan length is 174.
f
For more information about the enhanced configuration device JTAG support, refer to
the BSDL files provided at the Altera website.
Enhanced configuration devices can also be programmed by third-party flash
programmers or on-board processors using the external flash interface. Programming
files (.pof) can be converted to an Intel HEX format file (.hexout) using the Quartus II
Convert Programming Files utility, for use with the programmers or processors.
You can also program the enhanced configuration devices using the Quartus II
software, the Altera Programming Unit (APU), and the appropriate configuration
device programming adapter. Table 1–12 lists which programming adapter to use
with each enhanced configuration device.
Table 1–12. Programming Adapters
Device
EPC16
© December 2009
Package
Adapter
88-pin UFBGA
PLMUEPC-88
100-pin PQFP
PLMQEPC-100
EPC8
100-pin PQFP
PLMQEPC-100
EPC4
100-pin PQFP
PLMQEPC-100
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–28
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
IEEE Std. 1149.1 (JTAG) Boundary-Scan
IEEE Std. 1149.1 (JTAG) Boundary-Scan
The enhanced configuration device provides JTAG BST circuitry that complies with
the IEEE Std. 1149.1-1990 specification. JTAG boundary-scan testing can be performed
before or after configuration, but not during configuration.
Figure 1–6 shows the timing requirements for the JTAG signals.
Figure 1–6. JTAG Timing Waveforms
TMS
TDI
tJCP
tJCH
tJCL
tJPSU
tJPH
TCK
t JPZX
tJPXZ
tJPCO
TDO
tJSSU
Signal
to be
Captured
tJSH
tJSZX
tJSCO
tJSXZ
Signal
to be
Driven
Table 1–13 lists the timing parameters and values for the enhanced configuration
device.
Table 1–13. JTAG Timing Parameters and Values
Symbol
Parameter
Min
Max
Unit
100
—
ns
tJCP
TCK clock period
tJCH
TCK clock high time
50
—
ns
tJCL
TCK clock low time
50
—
ns
tJPSU
JTAG port setup time
20
—
ns
tJPH
JTAG port hold time
45
—
ns
tJPCO
JTAG port clock output
—
25
ns
tJPZX
JTAG port high impedance to valid output
—
25
ns
tJPXZ
JTAG port valid output to high impedance
—
25
ns
tJSSU
Capture register setup time
20
—
ns
tJSH
Capture register hold time
45
—
ns
tJSCO
Update register clock to output
—
25
ns
tJSZX
Update register high-impedance to valid output
—
25
ns
tJSXZ
Update register valid output to high impedance
—
25
ns
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Timing Information
1–29
Timing Information
Figure 1–7 shows the configuration timing waveform when using an enhanced
configuration device.
Figure 1–7. Configuration Timing Waveform Using an Enhanced Configuration Device
nINIT_CONF or VCC/nCONFIG
tPOR
OE/nSTATUS
nCS/CONF_DONE
DCLK
tDSU
tCL
Byte0
Byte1
tCH
tDH
tOEZX
DATA[7..0]
Byte2 Byte3
(2)
Byten
tCO
Tri-State
User I/O
User Mode
Tri-State
INIT_DONE
Notes to Figure 1–7:
(1) The enhanced configuration device will drive DCLK low after configuration.
(2) The enhanced configuration device will drive DATA[] high after configuration.
Table 1–14 defines the timing parameters when using the enhanced configuration
devices.
f
For more information about the flash memory (external flash interface) timing, refer
to the appropriate flash data sheet on the Altera website at www.altera.com.
■
For Micron flash-based EPC4, refer to the Micron MT28F400B3 Data Sheet Flash
Memory Used in EPC4 Devices at www.micron.com.
■
For Sharp flash-based EPC16, refer to the Sharp LHF16J06 Data Sheet Flash Memory
Used in EPC16 Devices at www.sharpsma.com.
■
For Intel flash-based EPC4 and EPC16, refer to Intel Flash 28F016B3 at
www.intel.com.
Table 1–14. Enhanced Configuration Device Configuration Parameters (Part 1 of 2)
Symbol
Parameter
Condition
Min
Typ
Max
Unit
40% duty cycle
—
—
66.7
MHz
—
15
—
—
ns
fDCLK
DCLK frequency
tDCLK
DCLK period
tHC
DCLK duty cycle high time
40% duty cycle
6
—
—
ns
tLC
DCLK duty cycle low time
40% duty cycle
6
—
—
ns
tCE
OE to first DCLK delay
—
40
—
—
ns
tOE
OE to first DATA available
—
40
—
—
ns
tOH
DCLK rising edge to DATA change
—
(1)
—
—
ns
tCF (2)
OE assert to DCLK disable delay
—
277
—
—
ns
tDF (2)
OE assert to DATA disable delay
—
277
—
—
ns
tRE (3)
DCLK rising edge to OE
—
60
—
—
ns
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–30
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Operating Conditions
Table 1–14. Enhanced Configuration Device Configuration Parameters (Part 2 of 2)
Symbol
Parameter
Condition
Min
Typ
Max
Unit
—
60
—
—
ns
40% duty cycle
—
—
100
MHz
tLOE
OE assert time to assure reset
fECLK
EXCLK input frequency
tECLK
EXCLK input period
—
10
—
—
ns
tECLKH
EXCLK input duty cycle high time
40% duty cycle
4
—
—
ns
tECLKL
EXCLK input duty cycle low time
40% duty cycle
4
—
—
ns
tECLKR
EXCLK input rise time
100 MHz
—
—
3
ns
tECLKF
EXCLK input fall time
100 MHz
—
—
3
ns
tPOR (4)
POR time
2 ms
1
2
3
ms
100 ms
70
100
120
ms
Notes to Table 1–14:
(1) To calculate tOH, use the following equation: tOH = 0.5 (DCLK period) - 2.5 ns.
(2) This parameter is used for CRC error detection by the FPGA.
(3) This parameter is used for CONF_DONE error detection by the enhanced configuration device.
(4) The FPGA VCCINT ramp time should be less than 1-ms for 2-ms POR, and it should be less than 70 ms for 100-ms POR.
Operating Conditions
Table 1–15 through Table 1–19 provide information about absolute maximum ratings,
recommended operating conditions, DC operating conditions, supply current values,
and pin capacitance data for the enhanced configuration devices.
Table 1–15. Enhanced Configuration Device Absolute Maximum Rating
Symbol
Parameter
Condition
Min
Max
Unit
VCC
Supply voltage
With respect to ground
-0.2
4.6
V
VI
DC input voltage
With respect to ground
-0.5
3.6
V
IMAX
DC VCC or ground current
—
—
100
mA
IOUT
DC output current, per pin
—
-25
25
mA
PD
Power dissipation
—
—
360
mW
TSTG
Storage temperature
No bias
-65
150
C
TAMB
Ambient temperature
Under bias
-65
135
C
TJ
Junction temperature
Under bias
—
135
C
Condition
Min
Max
Unit
—
3.0
3.6
V
With respect to ground
–0.3
VCC + 0.3
V
—
0
VCC
V
For commercial use
0
70
C
For industrial use
–40
85
C
Table 1–16. Enhanced Configuration Device Recommended Operating Conditions
Symbol
Parameter
VCC
Supplies voltage for 3.3-V operation
VI
Input voltage
VO
Output voltage
TA
Operating temperature
TR
Input rise time
—
—
20
ns
TF
Input fall time
—
—
20
ns
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Package
1–31
Table 1–17. Enhanced Configuration Device DC Operating Conditions
Symbol
Parameter
Condition
Min
Typ
Max
Unit
VCC
Supplies voltage to core
—
3.0
3.3
3.6
V
VIH
High-level input voltage
—
2.0
—
VCC +
0.3
V
VIL
Low-level input voltage
—
—
—
0.8
V
VOH
3.3-V mode high-level TTL output
voltage
IOH = –4 mA
2.4
—
—
V
3.3-V mode high-level CMOS
output voltage
IOH = –0.1 mA
VCC –
0.2
—
—
V
Low-level output voltage TTL
IOL = –4 mA DC
—
—
0.45
V
Low-level output voltage CMOS
IOL = –0.1 mA DC
—
—
0.2
V
II
Input leakage current
VI = VCC or ground
–10
—
10
A
IOZ
Tri-state output off-state current
VO = VCC or ground
–10
—
10
A
VOL
Table 1–18. Enhanced Configuration Device ICC Supply Current Values
Symbol
Parameter
Condition
Min
Typ
Max
Unit
ICC0
Current (standby)
—
—
50
150
A
ICC1
VCC supply current (during
configuration)
—
—
60
90
mA
ICCW
VCCW supply current
—
—
(1)
(1)
—
Note to Table 1–18:
(1) For VCCW supply current information, refer to the appropriate flash memory data sheet at www.altera.com.
Table 1–19. Enhanced Configuration Device Capacitance
Symbol
Parameter
Condition
Min
Max
Unit
CIN
Input pin capacitance
—
—
10
pF
COUT
Output pin capacitance
—
—
10
pF
Package
The EPC16 enhanced configuration device is available in both the 88-pin UFBGA
package and the 100-pin PQFP package. The UFBGA package, which is based on
0.8-mm ball pitch, maximizes board space efficiency. A board can be laid out for this
package using a single PCB layer. The EPC8 and EPC4 devices are available in the
100-pin PQFP package.
Enhanced configuration devices support vertical migration in the 100-pin PQFP
package.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–32
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Package
Figure 1–8 shows the PCB routing for the 88-pin UFBGA package. The Gerber file for
this layout is on the Altera website.
Figure 1–8. PCB Routing for 88-Pin UFBGA Package (Note 1)
NC
VCC
A20
A11
A15
A14
A13
A12
GND
DCLK
DATA7
NC
OE
C-WE#
A16
A8
A10
A9
DQ15
PGM0
DQ14
DQ7
DATA5
DATA6
F-WE#
RY/BY#
nINIT
CONF
PGM1
DQ13
DQ6
DQ4
DQ5
DATA4
TM1
VCC
DQ12
C-RP#
VCC
VCC
DATA3
(2)
TCK
TDI
TDO
(2)
(4)
GND
F-RP#
(5)
(2)
WP#
(2)
VCCW
A19
DQ11
VCC
DQ10
DQ2
DQ3
DATA2
(3)
TMS
NC
NC
PGM2
PORSEL
DQ9
DQ8
DQ0
DQ1
DATA1
VCC
nCS
A18
A17
A7
A6
A3
A2
A1
VCC
GND
DATA0
NC
GND
EXCLK
A5
A4
A0
CE#
GND
OE#
TM0
GND
NC
Notes to Figure 1–8:
(1) If the external flash interface feature is not used, then the flash pins should be left unconnected because they are internally connected to the
controller unit. The only pins that need external connections are WP#, WE#, and RP#. If the flash is being used as an external memory source,
then the flash pins should be connected as outlined in the pin descriptions section.
(2) F-RP# and F-WE# are pins on the flash die. C-RP# and C-WE# are pins on the controller die. C-WE# and F-WE# should be connected together
on the PCB. F-RP# and C-RP# should also be connected together on the PCB.
(3) WP# (write protection pin) should be connected to a high level (3.3 V) to be able to program the flash bottom boot block, which is required when
programming the device using the Quartus II software.
(4) RY/BY# is only available in Sharp flash-based enhanced configuration devices.
(5) Pin D3 is a NC pin for Intel Flash-based EPC16.
Package Layout Recommendation
Sharp flash-based EPC16 and EPC8 enhanced configuration devices in the 100-pin
PQFP packages have different package dimensions than other Altera 100-pin PQFP
devices (including the Micron flash-based EPC4, Intel flash-based EPC16, EPC8 and
EPC4). Figure 1–9 shows the 100-pin PQFP PCB footprint specifications for enhanced
configuration devices that allows for vertical migration between all devices. These
footprint dimensions are based on vendor-supplied package outline diagrams.
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Device Pin-Outs
1–33
Figure 1–9. Enhanced Configuration Device PCB Footprint Specifications for 100-Pin PQFP Packages (Note 1), (2)
0.65-mm Pad Pitch
0.325 mm
19.3 mm
0.410 mm
25.3 mm
2.4 mm
0.5
1.5
1.0
2.0 mm
Notes to Figure 1–9:
(1) Used 0.5-mm increase for front and back of nominal foot length.
(2) Used 0.3-mm increase to maximum foot width.
f
For package outline drawings, refer to the Altera Device Package Information Data Sheet.
Device Pin-Outs
f
© December 2009
For pin-out information, refer to Altera Configuration Devices Pin-Out Files.
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
1–34
Chapter 1: Enhanced Configuration Devices (EPC4, EPC8, and EPC16) Data Sheet
Chapter Revision History
Chapter Revision History
Table 1–20 lists the revision history for this chapter.
Table 1–20. Chapter Revision History
Date
Version
December 2009
2.8
October 2008
2.7
Changes Made
■
Added Table 1–1 and Table 1–2.
■
Updated Table 1–17 and Table 1–18.
■
Removed “Referenced Documents” section.
■
Updated Table 2–1, Table 2–7, and Table 2–8.
■
Updated Figure 2–2, Figure 2–3, and Figure 2–4.
■
Updated “JTAG-based Programming” section.
■
Added “Intel-Flash-Based EPC Device Protection” section.
■
Updated new document format.
May 2008
2.6
■
Minor textual and style changes. Added “Referenced Documents” section.
February 2008
2.5
■
Updated Table 2–18 with information about EPC16UI88AA.
May 2007
2.4
■
Added “Intel-Flash-Based EPC Device Protection” section.
April 2007
2.3
■
Added document revision history.
October 2005
2.2
■
Made changes to content.
July 2004
2.0
■
Added Stratix II and Cyclone II device information throughout chapter.
■
Updated VCCW connection in Figure 2–2, Figure 2–3, and Figure 2–4.
■
Updated (Note 2) of Figure 2–2, Figure 2–3, and Figure 2–4.
■
Updated (Note 4) of Table 2–12.
■
Updated unit of ICC0 in Table 2–16.
■
Added ICCW to Table 2–16.
■
Initial Release.
September 2003
1.0
Configuration Handbook (Complete Two-Volume Set)
© December 2009 Altera Corporation
Similar pages