LITEON LTL1CHKFK-0G1A Through hole lamp Datasheet

Through Hole Lamp
Product Data Sheet
LTL1CHKFK-0G1A
Spec No.: DS20-2003-098
Effective Date: 05/21/2003
Revision: -
LITE-ON DCC
RELEASE
BNS-OD-FC001/A4
LITE-ON Technology Corp. / Optoelectronics
No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C.
Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660
http://www.liteon.com/opto
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Features
* High luminous intensity output.
* Low power consumption.
* High efficiency.
* Versatile mounting on P.C. Board or panel.
* I.C. Compatible/low current requirement.
* 3.1 mm diameter package.
Package Dimensions
Part No.
LTL1CHKFK-0G1A
Lens
Water
Clear
Source Color
AlInGaP Yellow Orange
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25mm(.010") unless otherwise noted.
3. Protruded resin under flange is 1.0mm(.04") max.
4. Lead spacing is measured where the leads emerge from the package.
5. Specifications are subject to change without notice.
Part
No. : LTL1CHKFK-0G1A
BNS-OD-C131/A4
Page :
1
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Absolute Maximum Ratings at TA=25℃
Parameter
Maximum Rating
Unit
75
mW
60
mA
Continuous Forward Current
30
mA
Derating Linear From 50℃
0.4
mA/℃
5
V
Power Dissipation
Peak Forward Current
(1/10 Duty Cycle, 0.1ms Pulse Width)
Reverse Voltage
Operating Temperature Range
-40℃ to + 100℃
Storage Temperature Range
-55℃ to + 100℃
Lead Soldering Temperature
[1.6mm(.063") From Body]
Part
No. : LTL1CHKFK-0G1A
BNS-OD-C131/A4
260℃ for 5 Seconds
Page :
2
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Electrical / Optical Characteristics at TA=25℃
Parameter
Symbol
Min.
Typ.
IV
240
680
mcd
2θ1/2
45
deg
Peak Emission Wavelength
λP
611
nm
Dominant Wavelength
λd
605
nm
Δλ
17
nm
Forward Voltage
VF
2.05
Reverse Current
IR
Capacitance
C
Luminous Intensity
Viewing Angle
Spectral Line Half-Width
40
Max.
Unit
2.4
V
100
μA
pF
Test Condition
IF = 20mA
Note 1
Note 2 (Fig.5)
Measurement
@Peak (Fig.1)
Note 4
IF = 20mA
VR = 5V
VF = 0 , f = 1MHz
NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE
eye-response curve.
2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
3. Iv classification code is marked on each packing bag.
4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single
wavelength which defines the color of the device.
Part
No. : LTL1CHKFK-0G1A
BNS-OD-C131/A4
Page :
3
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Typical Electrical / Optical Characteristics Curves
(25℃
Part
No. : LTL1CHKFK-0G1A
BNS-OD-C131/A4
Ambient
Temperature
Unless
Otherwise
Noted)
Page :
4
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Features
* Compatible with radial lead automatic insertion equipment.
* Most radial lead plastic lead lamps available packaged in tape and folding.
* 5mm (0.197") formed lead spacing available.
* Folding packaging simplifies handling and testing.
Reel packaging is available by removing suffix “A” on option.
Package Dimensions
Specification
Item
Symbol
Minimum
Maximum
mm
inch
mm
inch
Tape Feed Hole Diameter
D
3.8
0.149
4.2
0.165
Component Lead Pitch
F
4.8
0.188
5.8
0.228
Front to Rear Deflection
△H
--
--
2.0
0.078
Height of Seating Plane
H
15.5
0.610
16.5
0.649
Feed Hole to Bottom of Component
H1
20.0
0.787
22.0
0.866
Feed Hole to Overall Component Height
H2
24.9
0.980
27.5
1.083
11.0
0.433
Lead Length After Component Height
L
Feed Hole Pitch
P
12.4
0.488
13.0
0.511
Lead Location
P1
3.15
0.124
4.55
0.179
Center of Component Location
P2
5.05
0.198
7.65
0.301
Total Taped Thickness
T
--
--
0.90
0.035
Feed Hole Location
W0
8.5
0.334
9.75
0.384
Adhesive Tape Width
W1
14.5
0.571
15.5
0.610
Adhesive Tape Position
W2
0
0
3.0
0.118
Tape Width
W3
17.5
0.689
19.0
0.748
Part
No. : LTL1CHKFK-0G1A
BNS-OD-C131/A4
W0
Page :
5
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Packing Spec
2500 pcs per inner carton
10 Inner cartons per outer carton
total 25000 pcs per outer carton
Part
No. : LTL1CHKFK-0G1A
BNS-OD-C131/A4
Page :
6
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Bin Code List
For Reference
Luminous Intensity
Bin Code
Min.
Max.
JK
240
400
LM
400
680
NP
680
1150
QR
1150
1900
Dominant Wavelength
Part
Unit : nm @20mA
Bin Code
Min.
Max.
H22
598.0
600.0
H23
600.0
603.0
H24
603.0
606.5
H25
606.5
610.0
H26
610.0
613.5
No. : LTL1CHKFK-0G1A
BNS-OD-C131/A4
Unit : mcd @20mA
Page :
7
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
CAUTIONS
1. Application limitation
The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment,
communication equipment and household application.) Consult Liteon’s sales in advance for information on
application in which exceptional quality and reliability are required, particularly when the failure or malfunction
of the LEDs may directly jeopardize life or health (such as airplanes, automobiles, traffic control equipment, life
support system and safety devices).
2. Storage
After being shipped from Liteon the LEDs should be kept at 30°C or less and 70%RH or less.
The LEDs should be used within 3 months. They can be stored for a year in a sealed container with a nitrogen
atmosphere and moisture absorbent material. Please avoid rapid transitions in ambient temperature in high
humidity environments where condensation may occur.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED.
4. Forming & Mounting
When forming a lead, the leads should be bent at a point at least 3mm from the base of epoxy bulb. Do not use
the base of the leadframe as a fulcrum during forming. Lead forming must be done before soldering at normal
temperature. When mounted through hole type LED lamp, avoid the occurrence of residual mechanical stress
due to clinching.
5. Soldering
When soldering, leave a minimum of 2mm clearance from the resin to the soldering point.
Dipping the resin into the solder must be avoided.
Do not apply any stress to the lead frame during soldering while the LED is at high temperature.
Recommended soldering condition
Soldering iron
Temperature
Soldering time
300°C Max.
3 sec. Max.
(one time only)
Wave soldering
Pre-heat
Pre-heat time
Solder wave
Soldering time
100°C Max.
60 sec. Max.
260°C Max.
10 sec. Max.
*The material of hook type Housing is very sensitive of soldering temperature. Any increase of soldering
temperature might seriously result in serious melting of the housing.
6. Drive Method
LED, a current operated device, requires specific current limit incorporated into the driving circuit. The current
control can be achieved by using a resistor in series with the LED. In order to prevent to exceed the allowed value
of 40% over desired forward current, the resistor should be well chosen for possible voltage variation. Two
possible circuit designs are shown below. The model A is recommended, and the model B will probably result in
uneven brightness between LEDs because of the Vf-If characteristics of LEDs.
Circuit model A
Circuit model B
LED
LED
Part
No. : LTL1CHKFK-0G1A
BNS-OD-C131/A4
Page :
8
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
7. ESD (Electrostatic Discharge)
Static electricity discharge or power surge will damage the LED. When handling the LED, it is highly
recommended to use a conductive wrist band or anti-electrostatic glove. All devices, equipment and machinery
must be properly grounded.
8. Reliability Test (for LED)
Classification
Endurance
Test
Test Item
Duration
/ Cycle
Test Condition
Room Temp.
Ta= Room Temp,
Operation Life
IDC= 30 mA
Referance Standard
1000 hrs
MIL-STD-202F:107D (1980)
Temperature
105℃ ~ 25℃ ~ -55℃ ~ 25℃
Cycling
30min
5mins
30mins
10 cycles
5mins
MIL-STD-750D:1051(1995)
MIL-STD-883D:1010 (1991)
JIS C 7021: A-4(1982)
Environmental
Test
Solder
MIL-STD-202F:210A(1980)
Solder temperature is 260± 5 ℃
10 sec
Resistance
MIL-STD-750D:2031(1995)
JIS C 7021: A-1(1982)
MIL-STD-202F:208D(1980)
Solderability
Solder temperature is 230± 5 ℃
5 sec
MIL-STD-750D:2026(1995)
MIL-STD-883D:2003(1991)
JIS C 7021: A-2(1982)
9. Others
The appearance and specifications of the product may be modified for the quality improvement without
further notice.
Part
No. : LTL1CHKFK-0G1A
BNS-OD-C131/A4
Page :
9
of
9
Similar pages