HLP-40H 40W Single Output Switching Power Supply series Features : Universal AC input / Full range (up to 305VAC) Built-in active PFC function, PF>0.95 Protections: Short circuit / Overload / Over voltage / Over temperature Cooling by free air convection Output constant current level adjustable 100% full load burn-in test Three in one dimming function (1~10Vdc or PWM signal or resistance) Suitable for built in LED lighting system Suitable for dry / damp location 3 years warranty M M SELV SPECIFICATION HLP-40H-12 HLP-40H-15 HLP-40H-20 HLP-40H-24 HLP-40H-30 HLP-40H-36 HLP-40H-42 HLP-40H-48 HLP-40H-54 MODEL 12V DC VOLTAGE CONSTANT CURRENT REGION Note.4 7.2 ~12V 48V 54V 25.2 ~ 42V 28.8 ~ 48V 32.4 ~ 54V 1.12A 0.96A 0.84A 0.75A 1.67A RATED POWER 40W 40W 40W 40.1W 40.2W 40.3W 40.3W 40.3W 40.5W 150mVp-p 150mVp-p 150mVp-p 200mVp-p 200mVp-p 300mVp-p 300mVp-p 300mVp-p 17 ~ 22V 22 ~ 27V 27 ~ 33V 33 ~ 40V 40 ~ 46V 44 ~ 53V 49 ~ 58V 10.8 ~ 13.5V 13.5 ~ 17V Can be adjusted by internal potential meter or through output cable CURRENT ADJ. RANGE 2 ~ 3.33A 1.6 ~ 2.67A 1.2 ~ 2A 1 ~ 1.67A 0.8 ~ 1.34A 0.67 ~ 1.12A 0.58 ~ 0.96A 0.5 ~ 0.84A 1.0% 1.0% 1.0% 0.45 ~ 0.75A VOLTAGE TOLERANCE Note.3 2.5% 2.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 1.5% 1.0% 2.0% Note.6 1500ms, 80ms / 115VAC at full load 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% VOLTAGE RANGE 16ms/230VAC Note.5 90 ~ 305VAC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF 0.95/230VAC EFFICIENCY (Typ.) 87% AC CURRENT (Typ.) INRUSH CURRENT(Typ.) OVER CURRENT Note.4 PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION 1000ms, 80ms / 230VAC at full load 16ms/115VAC at full load 127 ~ 431VDC PF 0.98/115VAC at full load and rated output voltage 88% 87% 0.43A / 115VAC 0.24A / 230VAC COLD START 70A/230VAC 89% 88% 0.23A / 277VAC 89% PF 0.9 at 60 ~ 100% load 89.5% 89.5% 90% 54 ~ 63V 59 ~ 66V 95 ~ 108% Protection type : Constant current limiting, recovers automatically after fault condition is removed 41 ~ 49V 18 ~ 24V 17.5 ~ 30V 23 ~ 30V 35 ~ 43V 48 ~ 58V 28 ~ 35V Protection type : Shut down o/p voltage, re-power on to recover 85 10 (RTH2) Protection type : Shut down o/p voltage, re-power on to recover -40 ~ +70 (Refer to "Derating Curve") 20 ~ 95% RH non-condensing -40 ~ +80 0.03%/ , 10 ~ 95% RH (0 ~ 50 ) 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS UL8750, EN61347-1, EN61347-2-13 approved ; Design refer to UL60950-1, TUV EN60950-1, EN60335-1 WITHSTAND VOLTAGE I/P-O/P:3.75KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN61000-3-2 Class C ( 60% load) ; EN61000-3-3 EMC EMISSION EMC IMMUNITY MTBF DIMENSION PACKING 1.0% <0.75mA / 277VAC LEAKAGE CURRENT NOTE 42V 21.6 ~ 36V 2A HOLD UP TIME (Typ.) OTHERS 36V 2.67A SETUP, RISE TIME EMC 30V 14.4 ~ 24V 3.33A LOAD REGULATION SAFETY & 24V 12 ~ 20V RATED CURRENT VOLTAGE ADJ. RANGE INPUT 20V 9 ~ 15V 18 ~ 30V 1.34A RIPPLE & NOISE (max.) Note.2 150mVp-p OUTPUT 15V I/P-FG:1.88KVAC O/P-FG:0.5KVAC Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level (surge 4KV), criteria A 287.9Khrs min. MIL-HDBK-217F (25 ) 147*53*27mm (L*W*H) 0.2Kg;72pcs/15.4Kg/1.09CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Constant current operation region is within 60% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. 5. Derating may be needed under low input voltages. Please check the static characteristics for more details. 6. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. 7. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. File Name:HLP-40H-SPEC 2011-06-03 HLP-40H 40W Single Output Switching Power Supply Mechanical Specification series Unit:mm 147 3.5 53 43 5 140 CN2 6 5 4 3 2 1 FS1 T3.15A/300V Io ADJ Vo ADJ 3max. 27max. CN1 6 5 4 3 2 1 AC Input Connector (CN1) : JST B6P-VH or equivalent Pin No. 1 2,4,5 3 6 Assignment AC/L No Pin AC/N FG DC Output Connector (CN2) : JST B6P-VH or equivalent Mating Housing Terminal JST VHR or equivalent JST SVH-21T-P1.1 or equivalent Pin No. 1 2 3,4 5,6 Assignment DIM+ DIM-V +V Mating Housing Terminal JST VHR or equivalent JST SVH-21T-P1.1 or equivalent Block Diagram fosc : 100KHz EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER POWER SWITCHING PFC CIRCUIT +V -V DIM+ DIM(B Type) O.L.P. O.T.P. FG O.L.P. DETECTION CIRCUIT PWM & PFC CONTROL O.V.P. Derating Curve Static Characteristics 100 100 90 80 80 230VAC Input only 70 50 LOAD (%) LOAD (%) 60 40 20 -40 -25 -10 0 15 30 50 AMBIENT TEMPERATURE ( ) 60 70 (HORIZONTAL) 60 50 40 90 100 125 135 145 155 165 175 180 200 230 305 INPUT VOLTAGE (V) 60Hz File Name:HLP-40H-SPEC 2011-06-03 40W Single Output Switching Power Supply HLP-40H series Power Factor Characteristic Constant Current Mode 1 0 .9 9 0 .9 8 0 .9 7 0 .9 6 0 .9 5 PF 0 .9 4 0 .9 3 277VAC 0 .9 2 230VAC 0 .9 1 110VAC 0 .9 0 .8 9 0 .8 8 0 .8 7 0 .8 6 0 .8 5 50% 60% 70% 80% 90% 100% (40W) LOAD EFFICIENCY vs LOAD (48V Model) HLG-40H series possess superior working efficiency that up to 90% can be reached in field applications. 92 90 EFFICIENCY (%) 88 86 84 82 277VAC 80 230VAC 78 110VAC 76 74 72 70 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B). (B) Constant Current area Vo(%) 100 (A) Constant Voltage area 60 (max.) (C) Hiccup Protection 50 95 Io (%) Typical LED power supply I-V curve File Name:HLP-40H-SPEC 2011-06-03 HLP-40H 40W Single Output Switching Power Supply series DIMMING OPERATION FG +V +V -V -V DIMDIM+ AC/N AC/L Output constant current level can be adjusted through output connector by 1~10VDC, PWM signal, or connecting a resistance between DIM+ and DIM-. Please DO NOT connect "DIM-" to "-V". Reference resistance value for output current adjustment (Typical) OPEN 10K 20K 30K 40K 50K 70K 80K 90K Single driver 60K 100K Resistance Multiple drivers value (N=driver quantity for synchronized 10K /N 20K /N 30K /N 40K /N 50K /N 60K /N 70K /N 80K /N 90K /N 100K /N ----- dimming operation) Percentage of rated current 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 95%~105% 1 ~ 10V dimming function for output current adjustment (Typical) Dimming value 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V OPEN Percentage of rated current 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 95%~105% 10V PWM signal for output current adjustment (Typical): Frequency range :100HZ ~ 3KHz Duty value 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% OPEN Percentage of rated current 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 95%~105% Using the built-in dimming function can't turn the lighting fixture totally dark. Please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the LED power supply unit. Dimming connection diagram for turning the lighting fixture ON/OFF : N FG L Switch Relay Adjuster 0~100K Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HLP-40H DIM+ DIMV(-) V(+) Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture. 1.Output constant current level can be adjusted through output connector by connecting a resistor or 1~10Vdc or 10V PWM signal between DIM+ and DIM-. 2.The LED lighting fixture can be turned ON/OFF by the switch. File Name:HLP-40H-SPEC 2011-06-03