RifY ge. on. A icati to chan N c I e t p c I M inal s ubje L is is not alimf its are s E R P otice:Tharametric N ep Som MITSUBISHI Dig./Ana.INTERFACE M62706ML,SL VOLTAGE DETECTING, SYSTEM RESETTING IC SERIES PIN CONFIGURATION (TOP VIEW) FEATURES • Few external components • Low operating threshold voltage (Supply voltage to keep a output low in a low supply operation) …0.65V(typ) at RL = 22kΩ • Wide supply voltage range ………… 2V to 7V • High immunity to a sudden supply voltage change • Wide application range • Extra small 3-pin package (3-pin FLAT) 3 OUTPUT 2 GND 1 SUPPLY VOLTAGE Outline SOT-89 (1) SUPPLY VOLTAGE (2) GND (3) OUTPUT APPLICATION • Reset pulse generation for almost all logic circuits • Battery checking, level detecting, waveform shaping circuits • Delayed waveform generating circuit • Switching circuit to a back-up power supply • DC/DC converter • Over voltage protection circuit (1) (2) (3) Outline TO-92L RECOMMENDED OPERATING CONDITION • Supply voltage range ………… 2V to 7V BLOCK DIAGRAM SUPPLY VOLTAGE 1 25µA typ. R1 3 OUTPUT R2 1.25V 2 GND ( 1 / 3 ) M62706SL M62706ML GENERAL DESCRIPTION The M62703ML/SL is a voltage threshold detector designed for detection of a supply voltage and generation of a system reset pulse for almost all logic circuits such as microcontroller. It has extensive applications including battery checking, level detecting and waveform shaping circuits. RifY ge. on. A icati to chan N c I e t p c I M inal s ubje L is is not alimf its are s E R P otice:Tharametric N ep Som MITSUBISHI Dig./Ana.INTERFACE M62706ML,SL VOLTAGE DETECTING, SYSTEM RESETTING IC SERIES FUNCTION DIAGRAM SUPPLY VOLTAGE 2.39V 0.65V OUTPUT STATE H L OUTPUT UNDEFINED ABSOLUTE MAXIMUM RATINGS (Ta=25°C, Unless otherwise noted) Symbol Parameter ICC Isink VO Supply Voltage Output Sink Current Output Voltage Pd Power Dissipation K0 - Thermal Derating Topr Tstg Operating Temperature Storage Temperature Test condition Ratings Unit V mA V 7 6 VCC 700 500 7 5 -30 to +85 -40 to +125 Output with constant current load 3pin SIL 3pin FLAT 3PIN SIL Ta≥25°C 3PIN FLAT mW mW/°C °C °C ELECTRICAL CHARACTERISTICS (Ta=25°C, Unless otherwise noted) Symbol VS ∆VS VS/∆T ICC Vsat VOPL IOC VOH tPHL tPLH Parameter Detecting Voltage Hysterisis Voltage Detecting Voltage Temperature Coefficient Circut Current Output Saturation Voltage Threshold Operating Voltage Output Load Current Output HIGH Voltage Propagation Deray Time Test condition MIN Limits TYP MAX 2.28 50 2.39 80 2.50 110 0.01 VCC=2.7V VCC=2V,Isink=4mA Minimum supply voltage RL=2.2kΩ,Vsat≤0.4V for IC operation RL=100kΩ,Vsat≤0.4V VCC=2V,VO=1/2VCC Response time when Vcc changes H to L Response time when Vcc changes L to H ( 2 / 3 ) -40 VCC-0.2 210 0.2 0.7 0.6 -25 VCC-0.06 6 3 340 0.4 0.8 0.7 -17 Unit V mV %/°C µA V V µA V µs RifY ge. on. A icati to chan N c I e t p c I M inal s ubje L is is not alimf its are s E R P otice:Tharametric N ep Som MITSUBISHI Dig./Ana.INTERFACE M62706ML,SL VOLTAGE DETECTING, SYSTEM RESETTING IC SERIES Example of application circuit Reset Circuit of M627XX Series VCC SUPPLY VOLTAGE SUPPLY VOLTAGE RL OUTPUT RESET(RESET) M627XX GND LOGIC CIRCUIT Cd GND Note 1. This IC can be used whether or not a pull-up resistor is included in the logic circuit. Note 2. The logic circuit preferably should not have a pull-down resistor. However in the case it has the resistor, the load resistor RL must be much less than the pull-down resistor. (refer to the above application circuit) ! Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury,fire or property damage.Remember to give due consideration to safety when making your circuit design,in order to prevent fires from spreading,redundancy,malfunction or other mishap. ( 3 / 3 )