ON NCP553SQ15T1G Cmos low iq nocap voltage regulator Datasheet

NCP553, NCV553
80 mA CMOS Low Iq
NOCAPE Voltage Regulator
This series of fixed output NOCAP linear regulators are designed
for handheld communication equipment and portable battery powered
applications which require low quiescent. This series features an
ultra−low quiescent current of 2.8 mA. Each device contains a voltage
reference unit, an error amplifier, a PMOS power transistor, resistors
for setting output voltage, current limit, and temperature limit
protection circuits.
These voltage regulators have been designed to be used with low
cost ceramic capacitors. The devices have the ability to operate
without an output capacitor. The devices are housed in the
micro−miniature SC82−AB surface mount package. Standard voltage
versions are 1.5, 1.8, 2.5, 2.7, 2.8, 3.0, 3.3, and 5.0 V. Other voltages
are available in 100 mV steps.
Features
•
•
Low Quiescent Current of 2.8 mA Typical
Low Output Voltage Option
Output Voltage Accuracy of 2.0%
Industrial Temperature Range of −40°C to 85°C
(NCV553, TA = −40°C to +125°C)
These are Pb−Free Devices
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
Typical Applications
SC82−AB (SC70−4)
SQ SUFFIX
CASE 419C
PIN CONNECTIONS &
MARKING DIAGRAMS
GND 1
Vin 2
4 N/C
xxxMG
G
•
•
•
•
http://onsemi.com
3 Vout
(NCP553, NCV553 Top View)
xxx = Device Code
M = Date Code*
G = Pb−Free Package
(Note: Microdot may be in either location)
• Battery Powered Consumer Products
• Hand−Held Instruments
• Camcorders and Cameras
*Date Code orientation and/or position may
vary depending upon manufacturing location.
ORDERING INFORMATION
Input
C1
GND
N/C
Vin
Vout
+
See detailed ordering and shipping information in the package
dimensions section on page 7 of this data sheet.
Output
+
C2
This device contains 32 active transistors
Figure 1. Typical Application Diagram
© Semiconductor Components Industries, LLC, 2016
November, 2016 − Rev. 5
1
Publication Order Number:
NCP553/D
NCP553, NCV553
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
PIN FUNCTION DESCRIPTION
Pin
Pin Name
1
GND
Description
2
Vin
Positive power supply input voltage.
3
Vout
Regulated output voltage.
−
Enable
4
N/C
Power supply ground.
This input is used to place the device into low−power standby. When this input is pulled low, the device
is disabled. If this function is not used, Enable should be connected to Vin.
No internal connection.
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Input Voltage
Vin
12
V
Output Voltage
Vout
−0.3 to Vin +0.3
V
Power Dissipation and Thermal Characteristics
Power Dissipation
Thermal Resistance, Junction−to−Ambient
PD
RqJA
Internally Limited
400
W
°C/W
Operating Junction Temperature
TJ
+125
°C
Operating Ambient Temperature
NCP553
NCV553
TA
Storage Temperature
Tstg
−40 to +85
−40 to +125
−55 to +150
°C
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL−STD−883, Method 3015
Machine Model Method 200 V
2. Latch up capability (85°C) ±200 mA DC with trigger voltage.
www.onsemi.com
2
NCP553, NCV553
ELECTRICAL CHARACTERISTICS
(Vin = Vout(nom.) + 1.0 V, Venable = Vin, Cin = 1.0 mF, Cout = 1.0 mF, TJ = 25°C, unless otherwise noted.)
Symbol
Characteristic
Min
Typ
Max
1.455
1.746
2.425
2.646
2.744
2.94
3.234
4.900
1.5
1.8
2.5
2.7
2.8
3.0
3.3
5.0
1.545
1.854
2.575
2.754
2.856
3.06
3.366
5.100
1.455
1.746
2.425
2.619
2.716
2.910
3.201
4.900
1.5
1.8
2.5
2.7
2.8
3.0
3.3
5.0
1.545
1.854
2.575
2.781
2.884
3.09
3.399
5.100
Unit
Output Voltage (TA = 25°C, Iout = 10 mA)
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.3 V
5.0 V
Vout
Output Voltage (TA = −40°C to 85°C, Iout = 10 mA)
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.3 V
5.0 V
Vout
Output Voltage (TA = −40°C, Iout = 10 mA)
NCV553 −5.0 V
Vout
4.900
5.0
5.100
V
Output Voltage (TA = +125°C, Iout = 10 mA)
NCV553 −5.0 V
Vout
4.850
5.0
5.150
V
Line Regulation (Vin = Vout + 1.0 V to 12 V, Iout = 10 mA)
Regline
−
2.0
4.5
mV/V
Load Regulation (Iout = 1.0 mA to 80 mA, Vin = Vout + 2.0 V)
Regload
−
0.3
0.8
mV/mA
Output Current (Vout = (Vout at Iout = 80 mA) −3.0%)
1.5 V−3.9 V (Vin = Vout(nom.) + 2.0 V)
4.0 V−5.0 V (Vin = 6.0 V)
Io(nom.)
80
80
180
180
−
−
Dropout Voltage (TA = −40°C to 125°C, Iout = 80 mA, Measured at
Vout −3.0%)
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.3 V
5.0 V
Vin−Vout
Quiescent Current
(Enable Input = 0 V)
(Enable Input = Vin, Iout = 1.0 mA to Io(nom.), Vin = Vout +2.0 V)
IQ
Output Short Circuit Current (Vout = 0 V)
1.5 V−3.9 V (Vin = Vout(nom.) + 2.0 V)
4.0 V−5.0 V (Vin = 6.0 V)
Iout(max)
V
V
mA
mV
−
−
−
−
−
−
−
−
1300
1100
800
750
730
680
650
470
1800
1600
1400
1200
1200
1000
1000
800
−
−
0.1
2.8
1.0
6.0
100
100
300
300
450
450
mA
mA
Output Voltage Noise (f = 20 Hz to 100 kHz, Iout = 10 mA)
(Cout = 1.0 mF)
Vn
−
90
−
mVrms
Output Voltage Temperature Coefficient
TC
−
"100
−
ppm/°C
3. Maximum package power dissipation limits must be observed.
T
*TA
PD + J(max)
RqJA
4. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
www.onsemi.com
3
NCP553, NCV553
DEFINITIONS
Load Regulation
Line Regulation
The change in output voltage for a change in output
current at a constant temperature.
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse technique such that the average
chip temperature is not significantly affected.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 3.0% below
its nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Line Transient Response
Typical over and undershoot response when input voltage
is excited with a given slope.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 160°C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Maximum Power Dissipation
The maximum total dissipation for which the regulator
will operate within its specifications.
Quiescent Current
The quiescent current is the current which flows through
the ground when the LDO operates without a load on its
output: internal IC operation, bias, etc. When the LDO
becomes loaded, this term is called the Ground current. It is
actually the difference between the input current (measured
through the LDO input pin) and the output current.
Maximum Package Power Dissipation
The maximum power package dissipation is the power
dissipation level at which the junction temperature reaches
its maximum operating value, i.e. 125°C. Depending on the
ambient power dissipation and thus the maximum available
output current.
www.onsemi.com
4
NCP553, NCV553
1
3.03
Vout(nom.) = 3.0 V
0.9
Vout, OUTPUT VOLTAGE (VOLTS)
Vin − Vout, DROPOUT VOLTAGE (VOLTS)
TYPICAL CHARACTERISTICS
0.8
0.7
80 mA
0.6
0.5
0.4
40 mA
0.3
0.2
0.1
0
−50
−25
0
50
25
75
100
Vout(nom.) = 3.3 V
3.025 Iout = 5 mA
3.02
3.01
3.005
3
−60
125
−20
−40
40
20
0
80
60
TEMPERATURE (_C)
TEMPERATURE (_C)
Figure 2. Dropout Voltage versus Temperature
Figure 3. Output Voltage versus Temperature
3
4.5
Iout = 0 mA
Vin = 4 V
Iq, QUIESCENT CURRENT (mA)
Iq, QUIESCENT CURRENT (mA)
Vin = 4 V
3.015
3.25
2.75
2.5
2.25
2
1.75
−60
−40
−20
0
20
40
60
80
3.5
3
2.5
2
1.5
1
0.5
0
100
0
2
3.5
3
2.5
OUTPUT VOLTAGE
DEVIATION (mV)
10 mA
1.5
50 mA
0.5
0
10
100
1000
10000
6
8
10
12
Figure 5. Quiescent Current versus Input Voltage
Vin, INPUT
VOLTAGE (V)
4
1
4
Vin, INPUT VOLTAGE (VOLTS)
Figure 4. Quiescent Current versus Temperature
2
100
Vout(nom.) = 3 V
Iout = 0 mA
4
TEMPERATURE (_C)
OUTPUT NOISE (mV/ǰHz)
Vin = 12 V
100000
1000000
6
Iout = 1 mA
Cout = 1 mF
5
4
200
100
0
−100
0
0.5
1
1.5
2
2.5
3
3.5
FREQUENCY (Hz)
TIME (ms)
Figure 6. Output Noise Density
Figure 7. Line Transient Response
www.onsemi.com
5
4
4.5
NCP553, NCV553
OUTPUT VOLTAGE
DEVIATION (mV)
TYPICAL CHARACTERISTICS
600
Vin = 4 V
Cout = 10 mF
400
200
0
Iout, OUTPUT
CURRENT (mA)
150
100
50
0
0
10
20
30
40
50
TIME (ms)
OUTPUT VOLTAGE
DEVIATION (mV)
Figure 8. Load Transient Response
200
0
−200
Vin = 4 V
Cout = 10 mF
Iout, OUTPUT
CURRENT (V)
−400
100
50
0
−50
0
0.5
1
1.5
2
TIME (ms)
Figure 9. Load Transient Response
Vout, OUTPUT VOLTAGE (VOLTS)
3.5
3
2.5
2
1.5
1
Cin = 1 mF
Cout = 1 mF
TA = 25 _C
0.5
0
0
2
4
6
8
10
12
Vin, INPUT VOLTAGE (VOLTS)
Figure 10. Output Voltage versus Input Voltage
www.onsemi.com
6
NCP553, NCV553
APPLICATIONS INFORMATION
Thermal
A typical application circuit for the NCP553 series is
shown in Figure 1, front page.
As power across the NCP553 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material and also the ambient
temperature effect the rate of temperature rise for the part.
This is stating that when the devices have good thermal
conductivity through the PCB, the junction temperature will
be relatively low with high power dissipation applications.
The maximum dissipation the package can handle is
given by:
Input Decoupling (C1)
A 1.0 mF capacitor either ceramic or tantalum is
recommended and should be connected close to the package.
Higher values and lower ESR will improve the overall line
transient response. If large line or load transients are not
expected, then it is possible to operate the regulator without
the use of a capacitor.
TDK capacitor: C2012X5R1C105K, or C1608X5R1A105K
Output Decoupling (C2)
T
*TA
PD + J(max)
RqJA
The NCP553 are very stable regulators and do not require
any specific Equivalent Series Resistance (ESR) or a
minimum output current. If load transients are not to be
expected, then it is possible for the regulator to operate with
no output capacitor. Otherwise, capacitors exhibiting ESRs
ranging from a few mW up to 10 W can thus safely be used.
The minimum decoupling value is 0.1 mF and can be
augmented to fulfill stringent load transient requirements.
The regulator accepts ceramic chip capacitors as well as
tantalum devices. Larger values improve noise rejection and
load regulation transient response.
TDK capacitor: C2012X5R1C105K, C1608X5R1A105K,
or C3216X7R1C105K
If junction temperature is not allowed above the
maximum 125°C, then the NCP553 can dissipate up to
250 mW @ 25°C.
The power dissipated by the NCP553 can be calculated
from the following equation:
Ptot + ƪVin * Ignd (Iout)ƫ ) [Vin * Vout] * Iout
or
P ) Vout * Iout
VinMAX + tot
Ignd ) Iout
If an 80 mA output current is needed then the ground
current from the data sheet is 2.8 mA. For an NCP553
(3.0 V), the maximum input voltage will then be 6.12 V.
Hints
Please be sure the Vin and GND lines are sufficiently
wide. When the impedance of these lines is high, there is a
chance to pick up noise or cause the regulator to
malfunction.
Set external components, especially the output capacitor,
as close as possible to the circuit, and make leads as short as
possible.
ORDERING INFORMATION
Nominal
Output Voltage
(Note 5)
Marking
NCP553SQ15T1G
NCP553SQ18T1G
NCP553SQ25T1G
NCP553SQ27T1G
NCP553SQ28T1G
NCP553SQ30T1G
NCP553SQ33T1G
NCP553SQ50T1G
1.5
1.8
2.5
2.7
2.8
3.0
3.3
5.0
LBE
LBF
LBG
LBH
LBI
LBJ
LBK
LBL
NCV553SQ15T1G*
NCV553SQ30T1G*
NCV553SQ50T1G*
1.5
3.0
5.0
AAF
LBJ
LFT
Device
Package
Shipping†
SC82−AB
(SC70−4)
(Pb−Free)
3000 Units/
8″ Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable
5. Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative.
www.onsemi.com
7
NCP553, NCV553
PACKAGE DIMENSIONS
SC−82AB (SC70−4)
SQ SUFFIX
CASE 419C−02
ISSUE F
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. 419C−01 OBSOLETE. NEW STANDARD IS
419C−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
A
G
C
D 3 PL
N
3
4
K
B
S
1
2
F
L
MILLIMETERS
MIN
MAX
1.80
2.20
1.15
1.35
0.80
1.10
0.20
0.40
0.30
0.50
1.10
1.50
0.00
0.10
0.10
0.26
0.10
−−−
0.05 BSC
0.20 REF
1.80
2.40
DIM
A
B
C
D
F
G
H
J
K
L
N
S
H
J
0.05 (0.002)
INCHES
MIN
MAX
0.071
0.087
0.045
0.053
0.031
0.043
0.008
0.016
0.012
0.020
0.043
0.059
0.000
0.004
0.004
0.010
0.004
−−−
0.002 BSC
0.008 REF
0.07
0.09
SOLDERING FOOTPRINT*
1.30
0.0512
0.65
0.026
0.95
0.037
0.90
0.035
0.70
0.028
1.90
0.075
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
NOCAP is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
◊
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
8
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP553D
Similar pages