Maxim MAX7034 315mhz/434mhz ask superheterodyne receiver 250î¼s startup time Datasheet

19-3109; Rev 2; 5/11
315MHz/434MHz ASK Superheterodyne
Receiver
The MAX7034 fully integrated low-power CMOS superheterodyne receiver is ideal for receiving amplitudeshift-keyed (ASK) data in the 300MHz to 450MHz
frequency range (including the popular 315MHz and
433.92MHz frequencies). The receiver has an RF sensitivity of -114dBm. With few external components and a
low-current power-down mode, it is ideal for cost-sensitive and power-sensitive applications typical in the
automotive and consumer markets. The MAX7034 consists of a low-noise amplifier (LNA), a fully differential
image-rejection mixer, an on-chip phase-locked loop
(PLL) with integrated voltage-controlled oscillator
(VCO), a 10.7MHz IF limiting amplifier stage with
received-signal-strength indicator (RSSI), and analog
baseband data-recovery circuitry.
Features
o Optimized for 315MHz or 433.92MHz Band
o Operates from Single +5.0V Supply
o Selectable Image-Rejection Center Frequency
o Selectable x64 or x32 fLO/fXTAL Ratio
o Low (< 6.7mA) Operating Supply Current
o < 3.0µA Low-Current Power-Down Mode for
Efficient Power Cycling
o 250µs Startup Time
o Built-In 44dB RF Image Rejection
o Excellent Receive Sensitivity Over Temperature
o -40°C to +125°C Operation
The MAX7034 is available in a 28-pin (9.7mm x 4.4mm)
TSSOP package and is specified over the automotive
(-40°C to +125°C) temperature range.
Applications
Automotive Remote
Keyless Entry
Security Systems
Garage Door Openers
Home Automation
Remote Controls
Local Telemetry
Wireless Sensors
Typical Application Circuit appears at end of data sheet.
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX7034AUI/V+T
-40°C to +125°C
28 TSSOP
/V denotes an automotive qualified part.
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
Pin Configuration
TOP VIEW
XTAL1 1
+
28 XTAL2
AVDD 2
27 SHDN
LNAIN 3
26 PDOUT
LNASRC 4
25 DATAOUT
AGND 5
LNAOUT 6
MAX7034
24 VDD5
23 DSP
AVDD 7
22 DFFB
MIXIN1 8
21 OPP
MIXIN2 9
20 DSN
AGND 10
19 DFO
IRSEL 11
18 IFIN2
MIXOUT 12
17 IFIN1
DGND 13
16 XTALSEL
DVDD 14
15 EN_REG
TSSOP
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
MAX7034
General Description
MAX7034
315MHz/434MHz ASK Superheterodyne
Receiver
ABSOLUTE MAXIMUM RATINGS
VDD5 to AGND.......................................................-0.3V to +6.0V
AVDD to AGND .....................................................-0.3V to +4.0V
DVDD to DGND .....................................................-0.3V to +4.0V
AGND to DGND.....................................................-0.1V to +0.1V
IRSEL, DATAOUT, XTALSEL,
SHDN, EN_REG to AGND ....................-0.3V to (VDD5 + 0.3V)
All Other Pins to AGND ..........................-0.3V to (VDVDD + 0.3V)
Continuous Power Dissipation (TA = +70°C)
28-Pin TSSOP (derate 12.8mW/°C above +70°C) ..1025.6mW
Operating Temperature Range .........................-40°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature ......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(Typical Application Circuit, VDD5 = +4.5V to +5.5V, no RF signal applied. TA = -40°C to +125°C, unless otherwise noted. Typical values are at VDD5 = +5.0V and TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
Supply Voltage
Supply Current
Shutdown Supply Current
Input-Voltage Low
Input-Voltage High
Input Logic Current High
SYMBOL
VDD5
IDD
ISHDN
CONDITIONS
MIN
+5.0V nominal supply voltage
4.5
VSHDN = VDD5
TYP
5.5
8.2
fRF = 434MHz
7.2
8.7
VSHDN = 0V
3
EN_REG, SHDN
VDD5 0.4
XTALSEL
VDVDD 0.4
VIH
IIH
2
VOH
8
µA
V
V
µA
VDVDD 0.4
VDVDD 1.5
1.1
fRF = 315MHz, VIRSEL = 0V
DATAOUT Output-Voltage High
mA
0.4
15
fRF = 375MHz, VIRSEL = VDVDD/2
VOL
V
5.0
6.7
fRF = 434MHz, VIRSEL = VDVDD
DATAOUT Output-Voltage Low
UNITS
fRF = 315MHz
VIL
Image-Reject Select Voltage
(Note 2)
MAX
V
0.4
ISINK = 10µA
0.125
V
ISOURCE = 10µA
VDD5 0.125
V
_______________________________________________________________________________________
315MHz/434MHz ASK Superheterodyne
Receiver
(Typical Application Circuit, VDD5 = +4.5V to +5.5V, all RF inputs are referenced to 50Ω, fRF = 433.92MHz, TA = -40°C to +125°C,
unless otherwise noted. Typical values are at VDD5 = +5.0V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
GENERAL CHARACTERISTICS
Startup Time
tON
Receiver Input Frequency Range
fRF
Time for valid signal detection after VSHDN
= VDD5. Does not include baseband filter
settling.
250
300
Maximum Receiver Input Level
450
0
Sensitivity at TA = +25oC (Note 3)
Sensitivity at TA = +125°C
(Note 3)
Maximum Data Rate
µs
+25°C, 315MHz
-114
+25°C, 434MHz
-113
+125°C, 315MHz
-113
+125°C, 434MHz
-110
MHz
dBm
dBm
dBm
Manchester coded
33
NRZ coded
66
330Ω IF filter load
45
dB
-50
dBm
330
Ω
kbps
LNA/MIXER
LNA/Mixer Voltage Gain (Note 4)
LNA/Mixer Input-Referred 1dB
Compression Point
Mixer Output Impedance
ZOUT_MIX
Mixer Image Rejection
fRF = 434MHz, VIRSEL = VDVDD
42
fRF = 375MHz, VIRSEL = VDVDD/2
44
fRF = 315MHz, VIRSEL = 0V
44
dB
INTERMEDIATE FREQUENCY (IF)
Input Impedance
ZIN_IF
Operating Frequency
fIF
Bandpass response
3dB Bandwidth
RSSI Linearity
RSSI Dynamic Range
RSSI Level
330
Ω
10.7
MHz
10
MHz
±0.5
dB
80
dB
PRFIN < -120dBm
1.15
PRFIN > -40dBm
2.2
V
_______________________________________________________________________________________
3
MAX7034
AC ELECTRICAL CHARACTERISTICS
MAX7034
315MHz/434MHz ASK Superheterodyne
Receiver
AC ELECTRICAL CHARACTERISTICS (continued)
(Typical Application Circuit, VDD5 = +4.5V to +5.5V, all RF inputs are referenced to 50Ω, fRF = 433.92MHz, TA = -40°C to +125°C,
unless otherwise noted. Typical values are at VDD5 = +5.0V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DATA FILTER
Maximum Bandwidth
50
kHz
100
kHz
DATA SLICER
Comparator Bandwidth
Output High Voltage
VVDD5
V
Output Low Voltage
0
V
CRYSTAL OSCILLATOR
fRF = 433.92MHz
Crystal Frequency (Note 5)
fXTAL
fRF = 315MHz
VXTALSEL = 0V
6.6128
VXTALSEL = VDVDD
13.2256
VXTALSEL = 0V
4.7547
VXTALSEL = VDVDD
9.5094
Crystal Tolerance
50
Input Capacitance
Maximum Load Capacitance
From each pin to ground
CLOAD
MHz
ppm
6.2
pF
10
pF
Note 1: 100% tested at TA = +125°C. Guaranteed by design and characterization over entire temperature range.
Note 2: IRSEL is internally set to 375MHz IR mode. It can be left open when the 375MHz image-rejection setting is desired. Bypass
to AGND with a 1nF capacitor in a noisy environment.
Note 3: Peak power level. BER = 2 x 10-3, Manchester encoded, data rate = 4kbps, IF bandwidth = 280kHz.
Note 4: The voltage conversion gain is measured with the LNA input matching inductor and the LNA/Mixer resonator in place, and
does not include the IF filter insertion loss.
Note 5: Crystal oscillator frequency for other RF carrier frequency within the 300MHz to 450MHz range is (fRF - 10.7MHz)/64 for
XTALSEL = 0V, and (fRF - 10.7MHz)/32 for XTALSEL = VDVDD.
4
_______________________________________________________________________________________
315MHz/434MHz ASK Superheterodyne
Receiver
MAX7034
Typical Operating Characteristics
(Typical Application Circuit, VDD5 = +5.0V, fRF = 433.92MHz, TA = +25°C, unless otherwise noted.)
+85°C
7.2
7.0
+25°C
+105°C
+125°C
-40°C
6.8
8.0
MAX7034 toc02
+125°C
433.92MHz
10.00
7.5
7.0
6.5
+25°C
6.0
5.5
6.6
4.9
5.1
5.3
SUPPLY VOLTAGE (V)
5.5
0.01
250
SENSITIVITY vs. TEMPERATURE
-104
-106
350
400
450
RF FREQUENCY (MHz)
-130
500
2.20
-125
-120
-115
PEAK RF INPUT POWER (dBm)
-110
RSSI AND DELTA vs. IF INPUT POWER
RSSI vs. RF INPUT POWER
433.92MHz
-108
300
2.40
MAX7034 toc04
-102
315MHz
-40°C
IF BANDWIDTH = 280kHz
MAX7034 toc06
2.40
MAX7034 toc05
4.7
1.00
0.10
5.0
4.5
2.20
2.00
2.00
1.80
1.80
15
RSSI
10
5
1.60
-5
DELTA
1.60
-10
-114
1.40
1.40
1.20
1.20
-15
-116
-120
110
-140 -120 -100 -80 -60 -40
RF INPUT POWER (dBm)
UPPER SIDEBAND
45
49.7dB
IMAGE
REJECTION
35
fRF = 315MHz
50
IMAGE REJECTION (dB)
55
25
15
LOWER SIDEBAND
30
fRF = 433.92MHz
10
5
0
5
10
15
20
IF FREQUENCY (MHz)
25
30
52
50
48
315MHz
46
433.92MHz
44
42
0
-5
10
IMAGE REJECTION vs. TEMPERATURE
40
20
-25
-90 -80 -70 -60 -50 -40 -30 -20 -10 0
IF INPUT POWER (dBm)
0
IMAGE REJECTION vs. RF FREQUENCY
60
MAX7034 toc07
65
-20
IMAGE REJECTION (dB)
10
35
60
85
TEMPERATURE (°C)
MAX7034 toc08
-15
LNA/MIXER VOLTAGE GAIN
vs. IF FREQUENCY
LNA/MIXER VOLTAGE GAIN (dB)
1.00
1.00
-40
-20
MAX7034 toc09
-118
40
280 300 320 340 360 380 400 420 440 460 480
RF FREQUENCY (MHz)
-40
-15
10
35
60
85
TEMPERATURE (°C)
110
_______________________________________________________________________________________
5
DELTA
-112
RSSI (V)
0
315MHz
-110
RSSI (V)
SENSITIVITY (dBm)
+85°C
100.00
BIT-ERROR RATE (%)
7.4
+105°C
8.5
SUPPLY CURRENT (mA)
7.6
SUPPLY CURRENT (mA)
9.0
MAX7034 toc01
7.8
BIT-ERROR RATE
vs. PEAK RF INPUT POWER
SUPPLY CURRENT vs. RF FREQUENCY
MAX7034 toc03
SUPPLY CURRENT vs. SUPPLY VOLTAGE
Typical Operating Characteristics (continued)
(Typical Application Circuit, VDD5 = +5.0V, fRF = 433.92MHz, TA = +25°C, unless otherwise noted.)
NORMALIZED IF GAIN
vs. IF FREQUENCY
S11 MAGNITUDE PLOT OF RFIN
vs. FREQUENCY
40
30
S11 MAGNITUDE (dB)
-5
-10
-15
-20
MAX7034 toc12
MAX7034 toc11
0
S11 SMITH CHART PLOT OF RFIN
50
MAX7034 toc10
5
NORMALIZED IF GAIN (dB)
500MHz
WITH INPUT
MATCHING
20
10
0
315MHz
-10
200MHz
315MHz
-24.1dB
-20
-30
-25
-40
-30
-50
100
10
200 230 260 290 320 350 380 410 440 470 500
IF FREQUENCY (MHz)
FREQUENCY (MHz)
PHASE NOISE
vs. OFFSET FREQUENCY
fRF = 315MHz
fRF = 433.92MHz
-20
PHASE NOISE (dBc/Hz)
-20
0
MAX7033 toc13
0
PHASE NOISE
vs. OFFSET FREQUENCY
-40
-60
-80
-100
-120
MAX7033 toc14
1
PHASE NOISE (dBc/Hz)
MAX7034
315MHz/434MHz ASK Superheterodyne
Receiver
-40
-60
-80
-100
-120
-140
-140
10
100
1k
10k
100k
OFFSET FREQUENCY (Hz)
1M
10M
10
100
1k
10k
100k
1M
10M
OFFSET FREQUENCY (Hz)
Pin Description
6
PIN
NAME
1
XTAL1
Crystal Input 1
FUNCTION
2, 7
AVDD
Positive Analog Supply Voltage. For +5V operation, pin 2 is the output of an on-chip +3.4V lowdropout regulator, and should be bypassed to AGND with a 0.1µF capacitor as close as possible to
the pin. Pin 7 must be externally connected to the supply from pin 2, and bypassed to AGND with a
0.01µF capacitor as close as possible to the pin (see the Voltage Regulator section and the Typical
Application Circuit).
3
LNAIN
Low-Noise Amplifier Input. See the Low-Noise Amplifier section.
_______________________________________________________________________________________
315MHz/434MHz ASK Superheterodyne
Receiver
PIN
NAME
FUNCTION
4
LNASRC
5, 10
AGND
6
LNAOUT
8
MIXIN1
1st Differential Mixer Input. Connect to LC tank filter from LNAOUT through a 100pF capacitor. See
the Typical Application Circuit.
9
MIXIN2
2nd Differential Mixer Input. Connect to VDD3 side of the LC tank filter through a 100pF capacitor. See
the Typical Application Circuit.
11
IRSEL
Image-Rejection Select. Set VIRSEL = 0V to center image rejection at 315MHz. Leave IRSEL
unconnected to center image rejection at 375MHz. Set VIRSEL = DVDD to center image rejection at
434MHz. See the Mixer section.
12
MIXOUT
13
DGND
Digital Ground
14
DVDD
Positive Digital Supply Voltage. Connect to both of the AVDD pins. Bypass to DGND with a 0.01µF
capacitor as close as possible to the pin (see the Typical Application Circuit).
15
EN_REG
Regulator Enable. Connect to VDD5 to enable internal regulator. Pull this pin low to allow device
operation between +3.0V and +3.6V. See the Voltage Regulator section.
16
XTALSEL
Crystal Divider Ratio Select. Drive XTALSEL low to select fLO/fXTAL ratio of 64, or drive XTALSEL high
to select fLO/fXTAL ratio of 32.
17
IFIN1
1st Differential Intermediate-Frequency Limiter Amplifier Input. Connect to the output of a 10.7MHz
bandpass filter.
18
IFIN2
2nd Differential Intermediate-Frequency Limiter Amplifier Input. Bypass to AGND with a 1500pF
capacitor as close as possible to the pin.
19
DFO
Data Filter Output
20
DSN
Negative Data Slicer Input
21
OPP
Noninverting Op-Amp Input for the Sallen-Key Data Filter
22
DFFB
Data Filter Feedback Node. Input for the feedback of the Sallen-Key data filter.
23
DSP
Positive Data Slicer Input
24
VDD5
+5V Supply Voltage. Bypass to AGND with a 0.01µF capacitor as close as possible to the pin. For
+5V operation, VDD5 is the input to an on-chip voltage regulator whose +3.4V output appears at
AVDD pin 2. (see the Voltage Regulator section and the Typical Application Circuit).
25
DATAOUT
26
PDOUT
Low-Noise Amplifier Source for external Inductive Degeneration. Connect inductor to ground to set
LNA input impedance. See the Low-Noise Amplifier section.
Analog Ground
Low-Noise Amplifier Output. Connect to mixer input through an LC tank filter. See the Low-Noise
Amplifier section.
330Ω Mixer Output. Connect to the input of the 10.7MHz bandpass filter.
Digital Baseband Data Output
Peak-Detector Output
27
SHDN
Power-Down Select Input. Drive high to power up the IC. Internally pulled down to AGND with a
100kΩ resistor.
28
XTAL2
Crystal Input 2. Can also be driven with an external reference oscillator. See the Crystal Oscillator section.
_______________________________________________________________________________________
7
MAX7034
Pin Description (continued)
315MHz/434MHz ASK Superheterodyne
Receiver
MAX7034
Functional Diagram
LNASRC
4
LNAIN
AVDD
VDD5
AVDD
DVDD
DGND
AGND
3
EN_REG LNAOUT
15
6
MIXIN1 MIXIN2
8
9
7
14
13
5, 10
Q
IFIN2
18
IMAGE
REJECTION
∑
I
DIVIDE
BY 64
VCO
PHASE
DETECTOR
LOOP
FILTER
÷1
IF LIMITING
AMPS
90˚
3.4V REG
MAX7034
RSSI
DATA
FILTER
RDF1
100kΩ
RDF2
100kΩ
÷2
CRYSTAL
DRIVER
16
1
XTALSEL
XTAL1 XTAL2
28
DATA
SLICER
POWERDOWN
27
SHDN
25
DATAOUT
Detailed Description
The MAX7034 CMOS superheterodyne receiver and a
few external components provide the complete receive
chain from the antenna to the digital output data.
Depending on signal power and component selection,
data rates can be as high as 33kbps Manchester
(66kbps NRZ).
The MAX7034 is designed to receive binary ASK data
modulated in the 300MHz to 450MHz frequency range.
ASK modulation uses a difference in amplitude of the
carrier to represent logic 0 and logic 1 data.
Voltage Regulator
For operation with a single +4.5V to +5.5V supply voltage,
connect VDD5 and the EN_REG pin to the supply voltage.
An on-chip voltage regulator drives one of the AVDD pins
(pin 2) to approximately +3.4V. For proper operation,
DVDD and both AVDD pins must be connected together.
For operation with a single +3.0V to +3.6V supply voltage,
connect both the AVDD pins, DVDD, and VDD5 to the
supply voltage and connect the EN_REG pin to ground
(which disables the internal voltage regulator). If the
MAX7034 is powered from +3.0V to +3.6V, the performance is limited to the -40°C to +105°C range.
In either supply voltage mode, bypass VDD5, DVDD, and
the pin 7 AVDD pin to AGND with 0.01µF capacitors, and
the pin 2 AVDD to AGND with a 0.1µF capacitor, all
placed as close as possible to the pins.
8
IFIN1
17
0˚
LNA
2
24
MIXOUT
12
IRSEL
11
20
23
19
DSN DSP DFO
26
21
22
PDOUT
OPP
DFFB
Low-Noise Amplifier
The LNA is an nMOS cascode amplifier with off-chip
inductive degeneration. The gain and noise figures are
dependent on both the antenna matching network at
the LNA input and the LC tank network between the
LNA output and the mixer inputs.
The off-chip inductive degeneration is achieved by
connecting an inductor from LNASRC to AGND. This
inductor sets the real part of the input impedance at
LNAIN, allowing for a more flexible input impedance
match, such as a typical printed-circuit board (PCB)
trace antenna. A nominal value for this inductor with a
50Ω input impedance is 15nH, but is affected by the
PCB trace.
The LC tank filter connected to LNAOUT comprises L1
and C9 (see the Typical Application Circuit). Select L1
and C9 to resonate at the desired RF input frequency.
The resonant frequency is given by:
fRF =
1
2π L TOTAL × CTOTAL
where:
LTOTAL = L1 + LPARASITICS.
CTOTAL = C9 + CPARASITICS.
_______________________________________________________________________________________
315MHz/434MHz ASK Superheterodyne
Receiver
Mixer
A unique feature of the MAX7034 is the integrated
image rejection of the mixer. This device eliminates the
need for a costly front-end SAW filter for most applications. Advantages of not using a SAW filter are
increased sensitivity, simplified antenna matching, less
board space, and lower cost.
The mixer cell is a pair of double balanced mixers that
perform an IQ downconversion of the RF input to the
10.7MHz IF from a low-side injected LO (i.e., fLO = fRF fIF). The image-rejection circuit then combines these
signals to achieve 44dB of image rejection. Low-side
injection is required due to the on-chip image-rejection
architecture. The IF output is driven by a source follower biased to create a driving-point impedance of 330Ω;
this provides a good match to the off-chip 330Ω ceramic IF filter.
The IRSEL pin is a logic input that selects one of the
three possible image-rejection frequencies. When VIRSEL
= 0V, the image rejection is tuned to 315MHz. VIRSEL =
V DVDD/2 tunes the image rejection to 375MHz, and
VIRSEL = VDVDD tunes the image rejection to 434MHz.
The IRSEL pin is internally set to VDVDD/2 (image rejection at 375MHz) when it is left unconnected, thereby
eliminating the need for an external VDVDD/2 voltage.
Phase-Locked Loop
The PLL block contains a phase detector, charge
pump, integrated loop filter, VCO, asynchronous 64x
clock divider, and crystal oscillator driver. Besides the
crystal, this PLL does not require any external components. The VCO generates a low-side LO. The relationship between the RF, IF, and crystal frequencies is
given by:
f -f
f XTAL = RF IF
32 × M
Intermediate Frequency and RSSI
The IF section presents a differential 330Ω load to provide matching for the off-chip ceramic filter. The six
internal AC-coupled limiting amplifiers produce an
overall gain of approximately 65dB, with a bandpassfilter-type response centered near the 10.7MHz IF frequency with a 3dB bandwidth of approximately 10MHz.
The RSSI circuit demodulates the IF by producing a DC
output proportional to the log of the IF signal level, with
a slope of approximately 14.2mV/dB.
Applications Information
Crystal Oscillator
The crystal oscillator in the MAX7034 is designed to
present a capacitance of approximately 3pF between
the XTAL1 and XTAL2. If a crystal designed to oscillate
with a different load capacitance is used, the crystal is
pulled away from its intended operating frequency,
introducing an error in the reference frequency.
Crystals designed to operate with higher differential
load capacitance always pull the reference frequency
higher. For example, a 4.7547MHz crystal designed to
operate with a 10pF load capacitance oscillates at
4.7563MHz with the MAX7034, causing the receiver to
be tuned to 315.1MHz rather than 315.0MHz, an error
of about 100kHz, or 320ppm. It is very important to
use a crystal with a load capacitance that is equal to
the capacitance of the MAX7034 crystal oscillator
plus PCB parasitics.
In actuality, the oscillator pulls every crystal. The crystal’s natural frequency is really below its specified frequency, but when loaded with the specified load
capacitance, the crystal is pulled and oscillates at its
specified frequency. This pulling is already accounted
for in the specification of the load capacitance.
Additional pulling can be calculated if the electrical
parameters of the crystal are known. The frequency
pulling is given by:
fP =
⎞
CM ⎛
1
1
× 106
⎜
2 ⎝ CCASE + CLOAD CCASE + CSPEC ⎟⎠
where:
where:
fP is the amount the crystal frequency pulled in ppm.
M = 1 (VXTALSEL = VDVDD) or 2 (VXTALSEL = 0V)
To allow the smallest possible IF bandwidth (for best sensitivity), minimize the tolerance of the reference crystal.
CM is the motional capacitance of the crystal.
CCASE is the case capacitance.
CSPEC is the specified load capacitance.
CLOAD is the actual load capacitance.
When the crystal is loaded as specified (i.e., CLOAD =
CSPEC), the frequency pulling equals zero.
_______________________________________________________________________________________
9
MAX7034
LPARASITICS and CPARASITICS include inductance and
capacitance of the PCB traces, package pins, mixer
input impedance, etc. These parasitics at high frequencies cannot be ignored, and can have a dramatic effect
on the tank filter center frequency. The total parasitic
capacitance is generally between 4pF and 6pF.
MAX7034
315MHz/434MHz ASK Superheterodyne
Receiver
It is possible to use an external reference oscillator in
place of a crystal to drive the VCO. AC-couple the external oscillator to XTAL2 with a 1000pF capacitor. Drive
XTAL2 with a signal level of approximately 500mVP-P.
AC-couple XTAL1 to ground with a 1000pF capacitor.
Data Filter
The data filter is implemented as a 2nd-order lowpass
Sallen-Key filter. The pole locations are set by the combination of two on-chip resistors and two external
capacitors. Adjusting the value of the external capacitors changes the corner frequency to optimize for different data rates. The corner frequency should be set to
approximately 1.5 times the fastest expected data rate
from the transmitter. Keeping the corner frequency near
the data rate rejects any noise at higher frequencies,
resulting in an increase in receiver sensitivity.
The configuration shown in Figure 1 can create a
Butterworth or Bessel response. The Butterworth filter
offers a very flat amplitude response in the passband
and a rolloff rate of 40dB/decade for the two-pole filter.
The Bessel filter has a linear phase response, which
works well for filtering digital data. To calculate the
value of C5 and C6, use the following equations, along
with the coefficients in Table 1:
C5 =
b
a(100k)( π)(fC )
C6 =
a
4(100k)( π)(fC )
a threshold voltage. One input is supplied by the data
filter output. Both comparator inputs are accessible offchip to allow for different methods of generating the
slicing threshold, which is applied to the second comparator input.
The suggested data slicer configuration uses a resistor
(R1) connected between DSN and DSP with a capacitor (C4) from DSN to DGND (Figure 2). This configuration averages the analog output of the filter and sets the
threshold to approximately 50% of that amplitude. With
this configuration, the threshold automatically adjusts
as the analog signal varies, minimizing the possibility
for errors in the digital data. The values of R1 and C4
affect how fast the threshold tracks to the analog amplitude. Be sure to keep the corner frequency of the RC
circuit much lower than the lowest expected data rate.
Note that a long string of zeros or ones can cause the
threshold to drift. This configuration works best if a coding scheme, such as Manchester coding, which has an
equal number of zeros and ones, is used.
To prevent continuous toggling of DATAOUT in the
absence of an RF signal due to noise, add hysteresis to
the data slicer as shown in Figure 3.
Table 1. Coefficents to Calculate C5 and C6
FILTER TYPE
a
b
Butterworth (Q = 0.707)
1.414
1.000
Bessel (Q = 0.577)
1.3617
0.618
where fC is the desired 3dB corner frequency.
For example, to choose a Butterworth filter response
with a corner frequency of 5kHz:
C5 =
MAX7034
1.000
≈ 450pF
(1.414)(100kΩ)(3.14)(5kHz)
RSSI
1.414
C6 =
≈ 225pF
k
Ω
4
100
( )(
)(3.14)(5kHz)
Choosing standard capacitor values changes C5 to
470pF and C6 to 220pF, as shown in the Typical
Application Circuit.
RDF1
100kΩ
RDF2
100kΩ
22
DFFB
21
OPP
19
DFO
C6
C5
Data Slicer
The data slicer takes the analog output of the data filter
and converts it to a digital signal. This is achieved by
using a comparator and comparing the analog input to
10
Figure 1. Sallen-Key Lowpass Data Filter
______________________________________________________________________________________
315MHz/434MHz ASK Superheterodyne
Receiver
MAX7034
Peak Detector
The peak-detector output (PDOUT), in conjunction with
an external RC filter, creates a DC output voltage equal
to the peak value of the data signal. The resistor provides a path for the capacitor to discharge, allowing the
peak detector to dynamically follow peak changes of
the data-filter output voltage. For faster data slicer
response, use the circuit shown in Figure 4. For more
details on hysteresis and peak-detector applications,
refer to Maxim Application Note 3671, Data Slicing
Techniques for UHF ASK Receivers.
MAX7034
DATA
SLICER
Layout Considerations
A properly designed PCB is an essential part of any
RF/microwave circuit. On high-frequency inputs and
outputs, use controlled-impedance lines and keep them
as short as possible to minimize losses and radiation.
At high frequencies, trace lengths that are on the order
of λ/10 or longer act as antennas.
Keeping the traces short also reduces parasitic inductance. Generally, 1 inch of a PCB trace adds about
20nH of parasitic inductance. The parasitic inductance
can have a dramatic effect on the effective inductance
of a passive component. For example, a 0.5 inch trace
connecting a 100nH inductor adds an extra 10nH of
inductance or 10%.
To reduce the parasitic inductance, use wider traces
and a solid ground or power plane below the signal
traces. Also, use low-inductance connections to ground
on all GND pins, and place decoupling capacitors
close to all power-supply pins.
Control Interface Considerations
When operating the MAX7034 with a +4.5V to +5.5V
supply voltage, the SHDN pin can be driven by a
microcontroller with either +3.0V or +5V interface logic
levels. When operating the MAX7034 with a +3.0V to
+3.6V supply, only +3.0V logic from the microcontroller
is allowed.
20
DSN
25
DATAOUT
19
DFO
23
DSP
R1
C4
Figure 2. Generating Data Slicer Threshold
MAX7034
DATA
SLICER
25
DATAOUT
20
DSN
23
DSP
R4
19
DFO
R1
R3
R2
C4
*OPTIONAL
Figure 3. Generating Data Slicer Hysteresis
MAX7034
DATA
SLICER
25
DATAOUT
20
DSN
23
DSP
19
DFO
26
PDOUT
25kΩ
47nF
Figure 4. Using PDOUT for Faster Startup
______________________________________________________________________________________
11
315MHz/434MHz ASK Superheterodyne
Receiver
MAX7034
Typical Application Circuit
IF VDD IS
THEN VDD3 IS
AND EN_REG IS
3.0V TO 3.6V
CONNECTED TO VDD
GROUNDED
4.5V TO 5.5V
CREATED BY LDO,
AVAILABLE AT AVDD
(PIN 2)
CONNECTED TO VDD
VDD3
VDD
(SEE TABLE)
X1
C13
C11
C12
1
RF INPUT
2
C1
L1
3
L2
4
5
6
VDD3
C14
7
L3
C3
C2
8
9
C4
C9
10
11
12
13
14
XTAL1
XTAL2
AVDD
SHDN
LNAIN
PDOUT
DATAOUT
LNASRC
AGND
MAX7034
LNAOUT
VDD5
DSP
AVDD
DFFB
MIXIN1
OPP
MIXIN2
DSN
AGND
DFO
IRSEL
IFIN2
MIXOUT
IFIN1
DGND
XTALSEL
DVDD
EN_REG
***
28
26
R2
25
C15
24
R3
23
22
21
C7
20
19
VDD
18
17
R1
**
16
15
*
Y1
TO/FROM µP
POWER-DOWN
DATA OUT
27
C5
C6
C8
IF FILTER
C10
IN
OUT
GND
COMPONENT VALUES
IN TABLE 2
12
***SEE THE MIXER SECTION.
*SEE THE PHASE-LOCKED
LOOP SECTION.
**SEE THE VOLTAGE
REGULATOR SECTION.
______________________________________________________________________________________
315MHz/434MHz ASK Superheterodyne
Receiver
MAX7034
Table 2. Component Values for Typical Application Circuit
COMPONENT
VALUE FOR
VALUE FOR
DESCRIPTION
C1
100pF
100pF
5%
C2
Open
Open
±0.1pF
C3
100pF
100pF
5%
C4
100pF
100pF
5%
C5
1500pF
1500pF
10%
C6
220pF
220pF
5%
C7
470pF
470pF
5%
C8
0.47µF
0.47µF
20%
C9
220pF
220pF
10%
C10
0.01µF
0.01µF
20%
C11
0.1µF
0.1µF
20%
C12
100pF
100pF
5%
C13
100pF
100pF
5%
C14
0.01µF
0.01µF
20%
C15
0.01µF
0.01µF
20%
L1
56nH
120nH
Murata LQP11A
L2
15nH
15nH
Murata LQP11A
L3
27nH
51nH
Murata LQP11A
R1
5.1kΩ
5.1kΩ
5%
R2
Open
Open
—
R3
0Ω
0Ω
—
X1 (÷64)
6.6128MHz*
4.7547MHz*
NDK or Suntsu
X1 (÷32)
13.2256MHz*
9.5094MHz*
NDK or Suntsu
Y1
10.7MHz ceramic filter
10.7MHz ceramic filter
Murata
*Crystal frequencies shown are for ÷64 (VXTALSEL = 0V) and ÷32 (VXTALSEL = VDD).
Package Information
Chip Information
PROCESS: CMOS
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
28 TSSOP
U28+1
21-0066
90-0171
______________________________________________________________________________________
13
MAX7034
315MHz/434MHz ASK Superheterodyne
Receiver
Revision History
PAGES
CHANGED
REVISION
NUMBER
REVISION
DATE
0
1/08
Initial release
—
1
3/09
Added /V designation to part number.
1
2
5/11
Updated Pin Description, Functional Diagram, Voltage Regulator section, Typical
Application Circuit, and Package Information; added Control Interface
Considerations section
DESCRIPTION
7, 8, 11, 12, 13
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
14 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2011 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
Similar pages