Features ◆ ◆ ◆ ◆ ◆ ◆ ◆ HIGH-SPEED 2.5V 256/128K x 36 ASYNCHRONOUS DUAL-PORT STATIC RAM WITH 3.3V 0R 2.5V INTERFACE On-chip port arbitration logic Full on-chip hardware support of semaphore signaling between ports Fully asynchronous operation from either port Separate byte controls for multiplexed bus and bus matching compatibility Sleep Mode Inputs on both ports Supports JTAG features compliant to IEEE 1149.1 Single 2.5V (±100mV) power supply for core LVTTL-compatible, selectable 3.3V (±150mV)/2.5V (±100mV) power supply for I/Os and control signals on each port Available in a 256-ball Ball Grid Array, 208-pin Plastic Quad Flatpack and 208-ball fine pitch Ball Grid Array. Industrial temperature range (–40°C to +85°C) is available for selected speeds Green parts available, see ordering information ◆ ◆ True Dual-Port memory cells which allow simultaneous access of the same memory location High-speed access – Commercial: 10/12/15ns (max.) – Industrial: 10/12ns (max.) RapidWrite Mode simplifies high-speed consecutive write cycles Dual chip enables allow for depth expansion without external logic IDT70T651/9 easily expands data bus width to 72 bits or more using the Master/Slave select when cascading more than one device M/S = VIH for BUSY output flag on Master, M/S = VIL for BUSY input on Slave Busy and Interrupt Flags IDT70T651/9S ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ Functional Block Diagram BE 3L BE 3R BE 2L BE 2R BE 1L BE 1R BE 0L BE 0R R/W L R/W R BB EE 01 LL CE 0L CE 1L BB EE 23 LL BBBB EEEE 3210 RRRR CE 0R CE 1R OEL OER Dout0-8_L Dout0-8_R Dout9-17_L Dout9-17_R Dout18-26_L Dout18-26_R Dout27-35_L Dout27-35_R 256/128K x 36 MEMORY ARRAY I/O0L- I/O35L A17L(1) A 0L Di n_L Address Decoder Di n_R ADDR_L CE0L CE1L OEL R/WL BUSYL(2,3) SEML INTL(3) I/O0R -I/O35R ARBITRATION INTERRUPT SEMAPHORE LOGIC OER (4) ZZ CONTROL CE0R CE1R A0R TDI JTAG TDO TCK TMS TRST R/WR BUSYR(2,3) SEMR INT R(3) M/S ZZL A17R(1) Address Decoder ADDR_R ZZR (4) LOGIC NOTES: 1. Address A17x is a NC for IDT70T659. 2. BUSY is an input as a Slave (M/S=VIL) and an output when it is a Master (M/S=VIH). 3. BUSY and INT are non-tri-state totem-pole outputs (push-pull). 4. The sleep mode pin shuts off all dynamic inputs, except JTAG inputs, when asserted. OPTx, INTx, M/S and the sleep mode pins themselves (ZZx) are not affected during sleep mode. 4869 drw 01 JULY 2015 1 ©2015 Integrated Device Technology, Inc. DSC-5632/8 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Description The IDT70T651/9 is a high-speed 256/128K x 36 Asynchronous Dual-Port Static RAM. The IDT70T651/9 is designed to be used as a stand-alone 9216/4608K-bit Dual-Port RAM or as a combination MASTER/SLAVE Dual-Port RAM for 72-bit-or-more word system. Using the IDT MASTER/SLAVE Dual-Port RAM approach in 72-bit or wider memory system applications results in full-speed, error-free operation without the need for additional discrete logic. This device provides two independent ports with separate control, address, and I/O pins that permit independent, asynchronous access for reads or writes to any location in memory. An automatic power down feature controlled by the chip enables (either CE0 or CE1) permit the on-chip circuitry of each port to enter a very low standby power mode. The IDT70T651/9 has a RapidWrite Mode which allows the designer to perform back-to-back write operations without pulsing the R/W input each cycle. This is especially significant at the 10ns cycle time of the IDT70T651/9, easing design considerations at these high performance levels. The 70T651/9 can support an operating voltage of either 3.3V or 2.5V on one or both ports, controlled by the OPT pins. The power supply for the core of the device (VDD) is at 2.5V. 2 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Pin Configuration(1,2,3) 70T651/9BC BC-256(5,6) 256-Pin BGA Top View A1 NC B1 I/O18L C1 A2 TDI B2 NC C2 I/O18R I/O19L D1 D2 A3 NC B3 TDO C3 VSS D3 I/O20R I/O19R I/O20L E1 E2 E3 A4 A5 A11L B4 B6 NC C4 A16L D4 VDD E4 B5 A15L C5 A13L D5 F2 F3 F4 E5 F5 I/O23L I/O22R I/O23R VDDQL VDD G1 G2 G3 G4 I/O24R I/O24L I/O25L VDDQR H1 H2 H3 H4 G5 VSS H5 I/O26L I/O25R I/O26R VDDQR VSS J1 J3 J2 J4 J5 I/O27L I/O28R I/O27R VDDQL ZZR K1 K2 K3 K4 K5 I/O29R I/O29L I/O28L V DDQL VSS L1 L2 L3 L4 L5 I/O30L I/O31R I/O30R VDDQR VDD M1 M2 M3 M4 I/O32R I/O32L I/O31L VDDQR N1 N2 N3 I/O33L I/O34R I/O33R P1 P2 P3 I/O35R I/O34L TMS R1 I/O35L T1 NC R2 NC T2 TCK R3 TRST T3 NC N4 VDD P4 A16R R4 NC T4 A12L C6 A10L D6 A7 A8L B7 A9L C7 A7L D7 A8 A9 BE2L B8 CE1L B9 A10 OEL B10 CE0L R/WL BE3L C9 C8 C10 A11 INT L B11 NC C11 BE1L BE0L SEML BUSYL D9 D8 D10 D11 A12 A5L B12 A4L C12 A6L D12 A13 A2L B13 A1L C13 A3L D13 A14 A0L B14 NC C14 A15 NC B15 I/O17L C15 A16 NC B16 NC C16 OPTL I/O17R I/O16L D14 D15 D16 VDDQL VDDQL VDDQR VDDQR VDDQL VDDQL VDDQR VDDQR VDD I/O15R I/O15L I/O16R I/O21R I/O21L I/O22L VDDQL VDD F1 A6 A 17L(4) A 14L M5 VDD N5 E6 VDD F6 NC G6 VSS H6 V SS J6 VSS K6 VSS L6 NC M6 V DD N6 E7 VSS F7 VSS G7 VSS H7 VSS J7 VSS K7 VSS L7 VSS M7 VSS N7 E8 E9 VSS F8 V SS F9 V SS VSS G8 G9 VSS H8 V SS H9 VSS J8 VSS J9 VSS K8 V SS K9 VSS L8 V SS L9 VSS M8 V SS M9 VSS N8 V SS N9 E10 VSS F10 VSS G10 VSS H10 V SS J10 VSS K10 VSS L10 V SS M10 VSS N10 E11 VDD F11 VSS G11 VSS H11 VSS J11 VSS K11 VSS L11 VSS M11 VDD N11 E12 F12 A13R R5 A15R T5 A17R(4) A14R P6 A10R R6 A12R T6 A11R P7 A7R R7 A9R T7 A8R P8 P9 P10 P11 BE1R BE0R SEMR BUSYR R8 R9 R10 BE3R CE0R R/W R T8 T9 BE2R CE1R T10 OER R11 M/S T11 INT R E14 E15 E16 F13 F14 F15 F16 VDD VDDQR I/O12R I/O13R I/O12L G12 VSS H12 VSS J12 G13 G14 G15 G16 VDDQL I/O10L I/O11L I/O11R H13 H14 VDDQL I/O9R J13 J14 H15 H16 IO9L I/O10R J15 J16 ZZL VDDQR I/O8R I/O7R I/O8L K12 VSS L12 VDD M12 VDD N12 V DDQR VDDQR VDDQL VDDQL VDDQR VDDQR VDDQL VDDQL P5 E13 VDD VDDQR I/O13L I/O14L I/O14R P12 A6R R12 A4R T12 A5R K13 K14 K15 K16 VDDQR I/O6R I/O6L I/O7L L13 L14 VDDQL I/O5L M13 M14 VDDQL I/O3R N13 VDD P13 A3R R13 A1R T13 A2R N14 I/O2L P14 L15 M15 OPTR T14 A0R M16 I/O3L I/O4L N15 N16 I/O1R I/O2R P15 I/O0L I/O0R R14 L16 I/O4R I/O5R R15 NC T15 NC P16 I/O1L R16 NC T16 NC 5632 drw 02f NOTES: 1. All VDD pins must be connected to 2.5V power supply. 2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VDD (2.5V), and 2.5V if OPT pin for that port is set to VSS (0V). 3. All VSS pins must be connected to ground supply. 4. A17X is a NC for IDT70T659. 5. Package body is approximately 17mm x 17mm x 1.4mm, with 1.0mm ball-pitch. 6. This package code is used to reference the package diagram. 3 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 70T651/9DR DR-208(5,6,7) 208-Pin PQFP Top View(8) I/O16L I/O16R I/O15L I/O15R VSS VDDQL I/O14L I/O14R I/O13L I/O13R VSS VDDQR I/O12L I/O12R I/O11L I/O11R VSS VDDQL I/O10L I/O10R I/O9L I/O9R VSS VDDQR VDD VDD VSS VSS ZZL VDDQL I/O8R I/O8L I/O7R I/O7L VSS VDDQR I/O6R I/O6L I/O5R I/O5L VSS VDDQL I/O4R I/O4L I/O3R I/O3L VSS VDDQR I/O2R I/O2L I/O1R I/O1L 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 I/O19L I/O19R I/O20L I/O20R VDDQL VSS I/O21L I/O21R I/O22L I/O22R VDDQR VSS I/O23L I/O23R I/O24L I/O24R VDDQL VSS I/O25L I/O25R I/O26L I/O26R VDDQR ZZR VDD VDD VSS VSS VDDQL VSS I/O27R I/O27L I/O28R I/O28L VDDQR VSS I/O29R I/O29L I/O30R I/O30L VDDQL VSS I/O31R I/O31L I/O32R I/O32L VDDQR VSS I/O33R I/O33L I/O34R I/O34L 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 VSS VDDQR I/O18R I/O18L VSS VDD TDI TDO NC NC A17L(4) A16L A15L A14L A13L A12L A11L A10L A9L A8L A7L BE3L BE2L BE1L BE0L CE1L CE0L VDD VDD VSS VSS SEML OEL R/WL BUSYL INTL NC A6L A5L A4L A3L A2L A1L A0L VDD VDD VSS OPTL I/O17L I/O17R VDDQR VSS Pin Configurations(1,2,3) (con't.) VSS VDDQL I/O35R I/O35L VDD TMS TCK TRST NC NC A17R(4) A16R A15R A14R A13R A12R A11R A10R A9R A8R A7R BE3R BE2R BE1R BE0R CE1R CE0R VDD VDD VSS VSS SEMR OER R/WR BUSYR INTR M/S A6R A5R A4R A3R A2R A1R A0R VDD VSS VSS OPTR I/O0L I/O0R VDDQL VSS 5632 drw 02d NOTES: 1. All VDD pins must be connected to 2.5V power supply. 2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VDD (2.5V) and 2.5V if OPT pin for that port is set to VSS (0V). 3. All VSS pins must be connected to ground. 4. A17X is a NC for IDT70T659. 5. Package body is approximately 28mm x 28mm x 3.5mm. 6. This package code is used to reference the package diagram. 7. 10ns Industrial speed grade is not available in the DR-208 package. 8. This text does not indicate orientation of the actual part-marking. 4 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Pin Configurations(1,2,3)(con't.) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 A A I/O19L I/O18L VSS TDO NC A1 6L A 12L A 8L BE1L VDD SEML INTL A4L A0L OPTL I/O 17L B I/O 20R VSS I/O18R TDI A 17L (4) A 13L A9 L BE 2L CE0L V SS BUSYL A5L A 1L VSS VDDQR I/O16L I/O15R C V DDQL I/O19R V DDQR V DD NC A 14 L A1 0L BE3 L CE1L V SS R/WL A6L A2L VDD I/O16R I/O 15L VSS C D I/O22L VSS I/O21L I/O 20 L A 15 L A 11L A7 L BE0 L V DD OEL NC A 3L VDD I/O17R VDDQ L I/O14L I/O14R D E I/O 23L I/O22R VDDQR I/O21 R I/O12L I/O13R V SS I/O 13L E F V DDQL I/O23R I/O24L VSS VSS I/O12R I/O11L VDDQR F G I/O 26L VSS I/O25L I/O 2 4R I/O 9L V DDQL I/O 10L I/O11 R G H VDD I/O26R VDD I/O9R VSS I/O10R H J VDDQL VDD ZZL V DD VSS V DDQR J K I/O28R I/O7R VDDQL I/O8R V SS K L I/O 8L L 70T651/9BF BF-208 (5,6) V DDQR I/O 25R VSS B VSS ZZR VSS I/O 2 7R VS S I/O29R I/O28L VDDQR I/O27L I/O 6R I/O 7L V SS M V DDQL I/O29L I/O 30R V SS VSS I/O6L I/O5R VDDQR M N I/O 31L VSS I/O 31R I/O 30 L I/O3R V DDQ L I/O4R I/O5L N P I/O32R I/O32L VDDQR I/O3 5R R VSS I/O33L I/O34 R T I/O 33R I/O34L U VSS I/O35L 208-Ball fpBGA Top View(7) TRST A1 6R A 12 R A 8R BE1R V DD SEMR INTR A 4R I/O2L I/O 3L V SS I/O4L P TCK A 17R (4) A13R A9R BE2R CE0R V SS BUSY R A5 R A1R V SS VDDQL I/O1R VDDQR R VDDQL TMS NC A14R A1 0R BE3R CE1R VSS R/ WR A6R A2R VS S I/O0 R V SS I/O 2R T VDD NC A15R A 11R A7 R BE0R VDD OER M/S A 3R A0R VDD OPT R I/O0L I/O 1L U 5632 drw 02e NOTES: 1. All VDD pins must be connected to 2.5V power supply. 2. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VDD (2.5V) and 2.5V if OPT pin for that port is set to VSS (0V). 3. All VSS pins must be connected to ground. 4. A17X is a NC for IDT70T659. 5. Package body is approximately 15mm x 15mm x 1.4mm with 0.8mm ball pitch. 6. This package code is used to reference the package diagram. 7. This text does not indicate orientation of the actual part-marking. 5 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Pin Names Left Port Right Port Names CE0L, CE1L CE0R, CE1R Chip Enables (Input) R/WL R/WR Read/Write Enable (Input) OEL Output Enable (Input) OER (1) (1) A0L - A17L A0R - A17R Address (Input) I/O0L - I/O35L I/O0R - I/O35R Data Input/Output SEML SEMR Semaphore Enable (Input) INTL INTR Interrupt Flag (Output) BUSYL BUSYR Busy Flag (Output) BE0L - BE3L BE0R - BE3R Byte Enables (9-bit bytes) (Input) VDDQL VDDQR Power (I/O Bus) (3.3V or 2.5V)(2) (Input) OPTL OPTR Option for selecting VDDQX(2,3) (Input) ZZL ZZR Sleep Mode Pin(4) (Input) M/S Master or Slave Select (Input)(5) VDD Power (2.5V)(2) (Input) VSS Ground (0V) (Input) TDI Test Data Input TDO Test Data Output TCK Test Logic Clock (10MHz) (Input) TMS Test Mode Select (Input) TRST Reset (Initialize TAP Controller) (Input) NOTES: 1. Address A17x is a NC for IDT70T659. 2. VDD, OPTX, and VDDQX must be set to appropriate operating levels prior to applying inputs on I/OX. 3. OPTX selects the operating voltage levels for the I/Os and controls on that port. If OPTX is set to VDD (2.5V), then that port's I/Os and controls will operate at 3.3V levels and VDDQX must be supplied at 3.3V. If OPTX is set to VSS (0V), then that port's I/Os and controls will operate at 2.5V levels and VDDQX must be supplied at 2.5V. The OPT pins are independent of one another—both ports can operate at 3.3V levels, both can operate at 2.5V levels, or either can operate at 3.3V with the other at 2.5V. 4. The sleep mode pin shuts off all dynamic inputs, except JTAG inputs, when asserted. OPTx, INTx, M/S and the sleep mode pins themselves (ZZx) are not affected during sleep mode. It is recommended that boundry scan not be operated during sleep mode. 5. BUSY is an input as a Slave (M/S=VIL) and an output when it is a Master (M/S=VIH). 5632 tbl 01 6 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Truth Table I—Read/Write and Enable Control (1,2) OE SEM CE0 CE1 BE3 BE2 BE1 BE0 R/W ZZ Byte 3 I/O27-35 Byte 2 I/O18-26 Byte 1 I/O9-17 Byte 0 I/O0-8 MODE X H H X X X X X X L High-Z High-Z High-Z High-Z Deselected–Power Down X H X L X X X X X L High-Z High-Z High-Z High-Z Deselected–Power Down X H L H H H H H X L High-Z High-Z High-Z High-Z All Bytes Deselected X H L H H H H L L L High-Z High-Z High-Z DIN Write to Byte 0 Only X H L H H H L H L L High-Z High-Z DIN High-Z Write to Byte 1 Only X H L H H L H H L L High-Z DIN High-Z High-Z Write to Byte 2 Only X H L H L H H H L L DIN High-Z High-Z High-Z Write to Byte 3 Only X H L H H H L L L L High-Z High-Z DIN DIN Write to Lower 2 Bytes Only X H L H L L H H L L DIN DIN High-Z High-Z Write to Upper 2 bytes Only X H L H L L L L L L DIN DIN DIN DIN L H L H H H H L H L High-Z High-Z High-Z DOUT Read Byte 0 Only L H L H H H L H H L High-Z High-Z DOUT High-Z Read Byte 1 Only L H L H H L H H H L High-Z DOUT High-Z High-Z Read Byte 2 Only L H L H L H H H H L DOUT High-Z High-Z High-Z Read Byte 3 Only L H L H H H L L H L High-Z High-Z DOUT DOUT Read Lower 2 Bytes Only L H L H L L H H H L DOUT DOUT High-Z High-Z Read Upper 2 Bytes Only Write to All Bytes L H L H L L L L H L DOUT DOUT DOUT DOUT Read All Bytes H H L H L L L L X L High-Z High-Z High-Z High-Z Outputs Disabled X X X X X X X X X H High-Z High-Z High-Z High-Z High-Z Sleep Mode NOTES: 1. "H" = VIH, "L" = VIL, "X" = Don't Care. 2. It is possible to read or write any combination of bytes during a given access. A few representative samples have been illustrated here. 5632 tbl 02 Truth Table II – Semaphore Read/Write Control(1) Inputs(1) (2) Outputs R/W OE BE3 BE2 BE1 BE0 SEM I/O1-35 I/O0 H H L L L L L L DATAOUT DATAOUT Read Data in Semaphore Flag (3) H ↑ X X X X L L X DATAIN Write I/O0 into Semaphore Flag L X X X X X X L ______ ______ CE Mode Not Allowed NOTES: 1. There are eight semaphore flags written to I/O0 and read from all the I/Os (I/O0-I/O35). These eight semaphore flags are addressed by A0-A2. 2. CE = L occurs when CE0 = VIL and CE1 = VIH. CE = H when CE0 = VIH and/or CE1 = VIL. 3. Each byte is controlled by the respective BEn. To read data BEn = VIL. 7 5632 tbl 03 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Recommended Operating Temperature and Supply Voltage(1) Grade Commercial Industrial Recommended DC Operating Conditions with VDDQ at 2.5V Symbol Ambient Temperature GND 2.4 2.5 2.6 V 2.4 2.5 2.6 V VSS Ground 0 0 0 V VIH Input High Volltage (Address, Control & Data I/O Inputs)(3) 1.7 ____ VDDQ + 100mV(2) V VIH Input High Voltage JTAG 1.7 ____ VDD + 100mV (2) V VIH Input High Voltage ZZ, OPT, M/S VDD - 0.2V ____ VDD + 100mV (2) V VIL Input Low Voltage -0.3(1) ____ 0.7 V VIL Input Low Voltage ZZ, OPT, M/S -0.3(1) ____ 0.2 V -40OC to +85OC 0V 2.5V + 100mV Capacitance(1) (TA = +25°C, F = 1.0MHZ) PQFP ONLY COUT(3) Input Capacitance Output Capacitance Conditions(2) Max. Unit VIN = 3dV 8 pF VOUT = 3dV 10.5 pF 5632 tbl 05 5632 tbl 08 Recommended DC Operating Conditions with VDDQ at 3.3V Absolute Maximum Ratings(1) VTERM (VDD) Rating VDD Terminal Voltage with Respect to GND Commercial & Industrial -0.5 to 3.6 _ NOTES: 1. VIL (min.) = -1.0V for pulse width less than tRC/2 or 5ns, whichever is less. 2. VIH (max.) = VDDQ + 1.0V for pulse width less than tRC/2 or 5ns, whichever is less. 3. To select operation at 2.5V levels on the I/Os and controls of a given port, the OPT pin for that port must be set to VSS(0V), and VDDQX for that port must be supplied as indicated above. NOTES: 1. These parameters are determined by device characterization, but are not production tested. 2. 3dV references the interpolated capacitance when the input and output switch from 0V to 3V or from 3V to 0V. 3. COUT also references CI/O. Symbol Symbol Unit V Min. Typ. Max. Unit V DD Core Supply Voltage Parameter 2.4 2.5 2.6 V VDDQ I/O Supply Voltage (3) 3.15 3.3 3.45 V V SS Ground 0 0 0 V 2.0 ____ VDDQ + 150mV (2) V 1.7 ____ VDD + 100mV(2) V VDD - 0.2V ____ VDD + 100mV(2) V (1) 0.8 V 0.2 V VTERM(2) (VDDQ ) VDDQ Terminal Voltage with Respect to GND -0.3 to VDDQ + 0.3 V VIH Input High Voltage (Address, Control &Data I/O Inputs)(3) VTERM(2) (INPUTS and I/O's) Input and I/O Terminal Voltage with Respect to GND -0.3 to VDDQ + 0.3 V VIH Input High Voltage JTAG TBIAS(3) Temperature Under Bias C VIH Input High Voltage ZZ, OPT, M/S TSTG Storage Temperature TJN Junction Temperature -55 to +125 o -65 to +150 o +150 o IOUT(For VDDQ = 3.3V) DC Output Current 50 IOUT(For VDDQ = 2.5V) DC Output Current 40 Unit I/O Supply Voltage (3) 5632 tbl 04 CIN Max. Core Supply Voltage 2.5V + 100mV Parameter Typ. VDD NOTE: 1. This is the parameter TA. This is the "instant on" case temperature. Symbol Min. VDDQ 0V O Parameter VDD 0 C to +70 C O Industrial and Commercial Temperature Ranges C C _ V IL Input Low Voltage -0.3 ____ V IL Input Low Voltage ZZ, OPT, M/S -0.3(1) ____ 5632 tbl 06 NOTES: 1. VIL (min.) = -1.0V for pulse width less than tRC/2 or 5ns, whichever is less. 2. VIH (max.) = VDDQ + 1.0V for pulse width less than tRC/2 or 5ns, whichever is less. 3. To select operation at 3.3V levels on the I/Os and controls of a given port, the OPT pin for that port must be set to VDD (2.5V), and VDDQX for that port must be supplied as indicated above. mA mA 5632 tbl 07 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. This is a steady-state DC parameter that applies after the power supply has reached its nominal operating value. Power sequencing is not necessary; however, the voltage on any Input or I/O pin cannot exceed VDDQ during power supply ramp up. 3. Ambient Temperature under DC Bias. No AC Conditions. Chip Deselected. 8 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 2.5V ± 100mV) 70T651/9S Symbol Parameter Test Conditions (1) |ILI| Input Leakage Current (1,2) Min. Max. Unit VDDQ = Max., VIN = 0V to VDDQ ___ 10 µA |ILI| JTAG & ZZ Input Leakage Current VDD = Max. , VIN = 0V to VDD ___ +30 µA |ILO| Output Leakage Current(1,3) CE0 = VIH or CE1 = VIL, VOUT = 0V to VDDQ ___ 10 µA Output Low Voltage (1) IOL = +4mA, VDDQ = Min. ___ 0.4 V V V VOL (3.3V) (1) VOH (3.3V) Output High Voltage IOH = -4mA, VDDQ = Min. 2.4 ___ VOL (2.5V) Output Low Voltage (1) IOL = +2mA, VDDQ = Min. ___ 0.4 VOH (2.5V) Output High Voltage (1) IOH = -2mA, VDDQ = Min. 2.0 ___ NOTES: 1. VDDQ is selectable (3.3V/2.5V) via OPT pins. Refer to page 6 for details. 2. Applicable only for TMS, TDI and TRST inputs. 3. Outputs tested in tri-state mode. DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(3) (VDD = 2.5V ± 100mV) 70T651/9S10 Com'l & Ind(7) Symbol IDD ISB1(6) ISB2 (6) ISB3 ISB4(6) IZZ Parameter Test Condition Version 70T651/9S12 Com'l & Ind 70T651/9S15 Com'l Only Typ.(4) Max. Typ.(4) Max. Typ.(4) Max. Unit mA Dynamic Operating Current (Both Ports Active) CEL and CER= V IL, Outputs Disabled f = fMAX(1) COM'L S 300 405 300 355 225 305 IND S 300 445 300 395 ____ ____ Standby Current (Both Ports - TTL Level Inputs) CEL = CER = V IH f = fMAX(1) COM'L S 90 120 75 105 60 85 IND S 90 145 75 130 ____ ____ Standby Current (One Port - TTL Level Inputs) CE"A" = V IL and CE"B" = V IH(5) Active Port Outputs Disabled, f = fMAX(1) COM'L S 200 265 180 230 150 200 IND S 200 290 180 255 ____ ____ COM'L S 2 10 2 10 2 10 IND S 2 20 2 20 ____ ____ COM'L S 200 265 180 230 150 200 IND S 200 290 180 255 ____ ____ COM'L S 2 10 2 10 2 10 IND S 2 20 2 20 ____ ____ Full Standby Current Both Ports CEL and (Both Ports - CMOS CER > V DDQ - 0.2V, Level Inputs) V IN > V DDQ - 0.2V or V IN < 0.2V, f = 0(2) Full Standby Current (One Port - CMOS Level Inputs) Sleep Mode Current (Both Ports - TTL Level Inputs) CE"A" < 0.2V and CE"B" > V DDQ - 0.2V (5) V IN > V DDQ - 0.2V or V IN < 0.2V, Active Port, Outputs Disabled, f = fMAX(1) ZZL = ZZR = V IH f = fMAX(1) V 5632 tbl 09 mA mA mA mA mA 5632 tbl 10 NOTES: 1. At f = fMAX, address and control lines (except Output Enable) are cycling at the maximum frequency read cycle of 1/tRC, using "AC TEST CONDITIONS" at input levels of GND to 3.3V. 2. f = 0 means no address or control lines change. Applies only to input at CMOS level standby. 3. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 4. VDD = 3.3V, TA = 25°C for Typ, and are not production tested. IDD DC(f=0) = 100mA (Typ). 5. CEX = VIL means CE0X = VIL and CE1X = VIH CEX = VIH means CE0X = VIH or CE1X = VIL CEX < 0.2V means CE0X < 0.2V and CE1X > VDDQX - 0.2V CEX > VDDQX - 0.2V means CE0X > VDDQX - 0.2V or CE1X < 0.2V. "X" represents "L" for left port or "R" for right port. 6. ISB1, ISB2 and ISB4 will all reach full standby levels (ISB3) on the appropriate port(s) if ZZL and /or ZZR = VIH. 7. 10ns Industrial speed grade is available in BF-208 and BC-256 packages only. 9 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges AC Test Conditions (VDDQ - 3.3V/2.5V) GND to 3.0V / GND to 2.4V Input Pulse Levels 2ns Max. Input Rise/Fall Times Input Timing Reference Levels 1.5V/1.25V Output Reference Levels 1.5V/1.25V Figure 1 Output Load 5632 tbl 11 50Ω 50Ω DATAOUT 1.5V/1.25 10pF (Tester) 5632 drw 03 Figure 1. AC Output Test load. 4 3.5 3 ∆ tAA/tACE (Typical, ns) 2.5 2 1.5 1 0.5 0 0 20 40 60 80 100 120 ∆ Capacitance (pF) from AC Test Load 140 5632 drw 05 Figure 3. Typical Output Derating (Lumped Capacitive Load). 10 160 , IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(4) Symbol Parameter 70T651/9S10 Com'l Only 70T651/9S12 Com'l & Ind 70T651/9S15 Com'l Only Min. Max. Min. Max. Min. Max. Unit 10 ____ 12 ____ 15 ____ ns READ CYCLE tRC Read Cycle Time tAA Address Access Time ____ 10 ____ 12 ____ 15 ns (3) ____ 10 ____ 12 ____ 15 ns tABE Byte Enable Access Time (3) ____ 5 ____ 6 ____ 7 ns tAOE Output Enable Access Time ____ 5 ____ 6 ____ 7 ns tOH Output Hold from Address Change tACE tLZ Chip Enable Access Time 3 ____ 3 ____ 3 ____ ns (1,2) 0 ____ 0 ____ 0 ____ ns (1,2) 0 4 0 6 0 8 ns 0 ____ 0 ____ 0 ____ ns Output Low-Z Time tHZ Output High-Z Time tPU Chip Enable to Power Up Time(2) (2) tPD Chip Disable to Power Down Time ____ 8 ____ 8 ____ 12 ns tSOP Semaphore Flag Update Pulse (OE or SEM) ____ 4 ____ 6 ____ 8 ns tSAA Semaphore Address Access Time 2 10 2 12 2 15 ns 5632tbl 12 AC Electrical Characteristics Over the Operating Temperature and Supply Voltage(4) 70T651/9S10 Com'l Only 70T651/9S12 Com'l & Ind 70T651/9S15 Com'l Only Min. Max. Min. Max. Min. Max. Unit 10 ____ 12 ____ 15 ____ ns tEW (3) Chip Enable to End-of-Write 8 ____ 10 ____ 12 ____ ns tAW Address Valid to End-of-Write 8 ____ 10 ____ 12 ____ ns ns Symbol Parameter WRITE CYCLE tWC Write Cycle Time (3) tAS Address Set-up Time 0 ____ 0 ____ 0 ____ tWP Write Pulse Width 8 ____ 10 ____ 12 ____ ns tWR Write Recovery Time 0 ____ 0 ____ 0 ____ ns tDW Data Valid to End-of-Write 6 ____ 8 ____ 10 ____ ns 0 ____ 0 ____ 0 ____ ns ____ tDH Data Hold Time (4) (1,2) tWZ Write Enable to Output in High-Z 4 ____ 6 ____ 8 ns tOW Output Active from End-of-Write(1,2,4) 0 ____ 0 ____ 0 ____ ns SEM Flag Write to Read Time 5 ____ 5 ____ 5 ____ ns SEM Flag Contention Window 5 ____ 5 ____ 5 ____ ns tSWRD tSPS 5632 tbl 13 NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with Output Test Load (Figure 1). 2. This parameter is guaranteed by device characterization, but is not production tested. 3. To access RAM, CE= VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. Either condition must be valid for the entire tEW time. CE = VIL when CE0 = VIL and CE1 = VIH. CE = VIH when CE0 = VIH and/or CE1 = VIL. 4. These values are valid regardless of the power supply level selected for I/O and control signals (3.3V/2.5V). See page 6 for details. 5. 10ns Industrial speed grade is available in BF-208 and BC-256 packages only. 11 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Waveform of Read Cycles(5) tRC ADDR (4) tAA (4) tACE (6) CE tAOE (4) OE tABE (4) BEn R/W tOH (1) tLZ/tLZOB DATAOUT VALID DATA (4) tHZ (2) BUSYOUT . tBDD (3,4) 5632 drw 06 NOTES: 1. Timing depends on which signal is asserted last, OE, CE or BEn. 2. Timing depends on which signal is de-asserted first CE, OE or BEn. 3. tBDD delay is required only in cases where the opposite port is completing a write operation to the same address location. For simultaneous read operations BUSY has no relation to valid output data. 4. Start of valid data depends on which timing becomes effective last tAOE, tACE, tAA, tABE or tBDD. 5. SEM = VIH. 6. CE = L occurs when CE0 = VIL and CE1 = VIH. CE = H when CE0 = VIH and/or CE1 = VIL. Timing of Power-Up Power-Down CE tPU tPD ICC 50% 50% ISB . 5632 drw 07 12 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Write Cycle No. 1, R/W Controlled Timing(1,5,8) tWC ADDRESS tHZ (7) OE tAW CE or SEM (9) (9) BEn (2) tAS (6) tWR tWP (3) R/W tWZ (7) tOW (4) DATAOUT (7) (4) tDW tDH DATAIN . 5632 drw 10 Timing Waveform of Write Cycle No. 2, CE Controlled Timing(1,5,8) tWC ADDRESS tAW CE or SEM (9) (6) tAS tWR(3) tEW (2) BEn(9) R/W tDW tDH DATAIN . 5632 drw 11 . NOTES: 1. R/W or CE or BEn = VIH during all address transitions for Write Cycles 1 and 2. 2. A write occurs during the overlap (tEW or tWP) of a CE = VIL, BEn = VIL, and a R/W = VIL for memory array writing cycle. 3. tWR is measured from the earlier of CE, BEn or R/W (or SEM or R/W) going HIGH to the end of write cycle. 4. During this period, the I/O pins are in the output state and input signals must not be applied. 5. If the CE or SEM = VIL transition occurs simultaneously with or after the R/W = VIL transition, the outputs remain in the High-impedance state. 6. Timing depends on which enable signal is asserted last, CE or R/W. 7. This parameter is guaranteed by device characterization, but is not production tested. Transition is measured 0mV from steady state with the Output Test Load (Figure 1). 8. If OE = VIL during R/W controlled write cycle, the write pulse width must be the larger of tWP or (tWZ + tDW) to allow the I/O drivers to turn off and data to be placed on the bus for the required tDW. If OE = VIH during an R/W controlled write cycle, this requirement does not apply and the write pulse can be as short as the specified tWP. 9. To access RAM, CE = VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. tEW must be met for either condition. CE = VIL when CE0 = VIL and CE1 = VIH. CE = VIH when CE0 = VIH and/or CE1 = VIL. 13 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM RapidWrite Mode Write Cycle Industrial and Commercial Temperature Ranges taken to still meet the Write Cycle time (tWC), the time in which the Address inputs must be stable. Input data setup and hold times (tDW and tDH) will now be referenced to the ending address transition. In this RapidWrite Mode the I/O will remain in the Input mode for the duration of the operations due to R/W being held low. All standard Write Cycle specifications must be adhered to. However, tAS and tWR are only applicable when switching between read and write operations. Also, there are two additional conditions on the Address Inputs that must also be met to ensure correct address controlled writes. These specifications, the Allowable Address Skew (tAAS) and the Address Rise/Fall time (tARF), must be met to use the RapidWrite Mode. If these conditions are not met there is the potential for inadvertent write operations at random intermediate locations as the device transitions between the desired write addresses. Unlike other vendors' Asynchronous Random Access Memories, the IDT70T651/9 is capable of performing multiple back-to-back write operations without having to pulse the R/W, CE, or BEn signals high during address transitions. This RapidWrite Mode functionality allows the system designer to achieve optimum back-to-back write cycle performance without the difficult task of generating narrow reset pulses every cycle, simplifying system design and reducing time to market. During this new RapidWrite Mode, the end of the write cycle is now defined by the ending address transition, instead of the R/W or CE or BEn transition to the inactive state. R/W, CE, and BEn can be held active throughout the address transition between write cycles. Care must be Timing Waveform of Write Cycle No. 3, RapidWrite Mode Write Cycle(1,3) (4) tWC tWC tWC ADDRESS (2) CE or SEM (6) tEW BEn tWR tWP R/W (5) (5) tWZ tOW DATAOUT tDH tDH tDW tDW tDH tDW DATAIN 5632 drw 08 NOTES: 1. OE = VIL for this timing waveform as shown. OE may equal VIH with same write functionality; I/O would then always be in High-Z state. 2. A write occurs during the overlap (tEW or tWP) of a CE = VIL, BEn = VIL, and a R/W = VIL for memory array writing cycle. The last transition LOW of CE, BEn, and R/W initiates the write sequence. The first transition HIGH of CE, BEn, and R/W terminates the write sequence. 3. If the CE or SEM = VIL transition occurs simultaneously with or after the R/W = VIL transition, the outputs remain in the High-impedance state. 4. The timing represented in this cycle can be repeated multiple times to execute sequential RapidWrite Mode writes. 5. This parameter is guaranteed by device characterization, but is not production tested. Transition is measured 0mV from steady state with the Output Test Load (Figure 1). 6. To access RAM, CE = VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. tEW must be met for either condition. CE = VIL when CE0 = VIL and CE1 = VIH. CE = VIH when CE0 = VIH and/or CE1 = VIL. 14 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges AC Electrical Characteristics over the Operating Temperature Range and Supply Voltage Range for RapidWrite Mode Write Cycle(1) Symbol Parameter Min Max Unit tAAS Allowable Address Skew for RapidWrite Mode ____ 1 ns tARF Address Rise/Fall Time for RapidWrite Mode 1.5 ____ V/ns 5632 tbl 14 NOTE: 1. Timing applies to all speed grades when utilizing the RapidWrite Mode Write Cycle. Timing Waveform of Address Inputs for RapidWrite Mode Write Cycle A0 tARF tAAS (1) A17 tARF 5632 drw 09 NOTE: 1. A16 for IDT70T659. 15 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Semaphore Read after Write Timing, Either Side(1) tSAA A0-A2 VALID ADDRESS tAW VALID ADDRESS tWR tACE tEW SEM(1) tOH tSOP tDW I/O DATAOUT(2) VALID DATA IN VALID tAS tWP tDH R/W tSWRD OE tSOE tSOP Write Cycle Read Cycle 5632 drw 12 . NOTES: 1. CE0 = VIH and CE1 = VIL are required for the duration of both the write cycle and the read cycle waveforms shown above. Refer to Truth Table II for details and for appropriate BEn controls. 2. "DATAOUT VALID" represents all I/O's (I/O0 - I/O35) equal to the semaphore value. Timing Waveform of Semaphore Write Contention(1,3,4) A0"A"-A2"A" (2) SIDE "A" MATCH R/W"A" SEM"A" tSPS A0"B"-A2"B" (2) SIDE "B" MATCH R/W"B" SEM"B" 5632 drw 13 . NOTES: 1. DOR = DOL = VIL, CEL = CER = VIH. Refer to Truth Table II for appropriate BE controls. 2. All timing is the same for left and right ports. Port "A" may be either left or right port. "B" is the opposite from port "A". 3. This parameter is measured from R/W"A" or SEM"A" going HIGH to R/W"B" or SEM"B" going HIGH. 4. If tSPS is not satisfied,the semaphore will fall positively to one side or the other, but there is no guarantee which side will be granted the semaphore flag. 16 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range Symbol Parameter 70T651/9S10 Com'l Only 70T651/9S12 Com'l & Ind 70T651/9S15 Com'l Only Min. Max. Min. Max. Min. Max. Unit BUSY TIMING (M/S=VIH) tBAA BUSY Access Time from Address Match ____ 10 ____ 12 ____ 15 ns tBDA BUSY Disable Time from Address Not Matched ____ 10 ____ 12 ____ 15 ns tBAC BUSY Access Time from Chip Enable Low ____ 10 ____ 12 ____ 15 ns tBDC BUSY Disable Time from Chip Enable High ____ 10 ____ 12 ____ 15 ns 2.5 ____ 2.5 ____ 2.5 ____ ns ____ 10 ____ 12 ____ 15 ns 8 ____ 10 ____ 12 ____ ns tAPS Arbitration Priority Set-up Time tBDD BUSY Disable to Valid Data(3) tWH Write Hold After BUSY(5) (2) BUSY TIMING (M/S=VIL) tWB BUSY Input to Write(4) 0 ____ 0 ____ 0 ____ ns tWH Write Hold After BUSY(5) 8 ____ 10 ____ 12 ____ ns ____ 22 ____ 25 ____ 30 ns ____ 20 ____ 22 ____ 25 ns PORT-TO-PORT DELAY TIMING tWDD tDDD Write Pulse to Data Delay(1) Write Data Valid to Read Data Delay (1) 5632 tbl 15b NOTES: 1. Port-to-port delay through RAM cells from writing port to reading port, refer to "Timing Waveform of Write with Port-to-Port Read and BUSY (M/S = VIH)". 2. To ensure that the earlier of the two ports wins. 3. tBDD is a calculated parameter and is the greater of the Max. spec, tWDD – tWP (actual), or tDDD – tDW (actual). 4. To ensure that the write cycle is inhibited on port "B" during contention on port "A". 5. To ensure that a write cycle is completed on port "B" after contention on port "A". 6. 10ns Industrial speed grade is available in BF-208 and BC-256 packages only. AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(1,2,3) Symbol Parameter 70T651/9S10 Com'l Only 70T651/9S12 Com'l & Ind 70T651/9S15 Com'l Only Min. Max. Min. Max. Min. Max. SLEEP MODE TIMING (ZZx=VIH) tZZS Sleep Mode Set Time 10 ____ 12 ____ 15 ____ tZZR Sleep Mode Reset Time 10 ____ 12 ____ 15 ____ tZZPD Sleep Mode Power Down Time 10 ____ 12 ____ 15 ____ tZZPU Sleep Mode Power Up Time ____ 0 ____ 0 ____ 0 5632 tbl 15c NOTES: 1. Timing is the same for both ports. 2. The sleep mode pin shuts off all dynamic inputs, except JTAG inputs, when asserted. OPTx, INTx, M/S and the sleep mode pins themselves (ZZx) are not affected during sleep mode. It is recommended that boundary scan not be operated during sleep mode. 3. These values are valid regardless of the power supply level selected for I/O and control signals (3.3V/2.5V). See page 6 for details. 4. 10ns Industrial speed grade is available in BF-208 and BC-256 packages only. 5. This parameter is guaranteed by device characterization, but is not production tested. 17 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Write with Port-to-Port Read and BUSY (M/S = VIH)(2,4,5) tWC MATCH ADDR"A" tWP R/W"A" tDH tDW VALID DATAIN "A" (1) tAPS MATCH ADDR"B" tBDA tBAA tBDD BUSY"B" tWDD DATAOUT "B" VALID tDDD (3) . NOTES: 1. To ensure that the earlier of the two ports wins. tAPS is ignored for M/S = VIL (SLAVE). 2. CE0L = CE0R = VIL; CE1L = CE1R = VIH. 3. OE = VIL for the reading port. 4. If M/S = VIL (slave), BUSY is an input. Then for this example BUSY"A" = VIH and BUSY"B" input is shown above. 5. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite from port "A". Timing Waveform of Write with BUSY (M/S = VIL) tWP R/W"A" tWB(3) BUSY"B" tWH(1) R/W"B" (2) NOTES: 1. tWH must be met for both BUSY input (SLAVE) and output (MASTER). 2. BUSY is asserted on port "B" blocking R/W"B", until BUSY"B" goes HIGH. 3. tWB only applies to the slave mode. 5632 drw 15 18 . 5632 drw 14 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Waveform of BUSY Arbitration Controlled by CE Timing (M/S = VIH)(1) ADDR"A" and "B" ADDRESSES MATCH CE"A" tAPS (2) CE"B" tBAC tBDC BUSY"B" . 5632 drw 16 Waveform of BUSY Arbitration Cycle Controlled by Address Match Timing (M/S = VIH)(1,3,4) ADDR"A" ADDRESS "N" tAPS (2) ADDR"B" MATCHING ADDRESS "N" tBAA tBDA BUSY"B" , 5632 drw 17 NOTES: 1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”. 2. If tAPS is not satisfied, the BUSY signal will be asserted on one side or another but there is no guarantee on which side BUSY will be asserted. 3. CEX = VIL when CE0X = VIL and CE1X = VIH. CEX = VIH when CE0X = VIH and/or CE1X = VIL. 4. CE0X = OEX = BEnX = VIL. CE1X = VIH. AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(1,2) 70T651/9S10 Com'l Only Symbol Parameter 70T651/9S12 Com'l & Ind 70T651/9S15 Com'l Only Min. Max. Min. Max. Min. Max. Unit INTERRUPT TIMING tAS Address Set-up Time 0 ____ 0 ____ 0 ____ ns tWR Write Recovery Time 0 ____ 0 ____ 0 ____ ns tINS Interrupt Set Time ____ 10 ____ 12 ____ 15 ns tINR Interrupt Reset Time ____ 10 ____ 12 ____ 15 NOTES: 1. Timing is the same for both ports. 2. These values are valid regardless of the power supply level selected for I/O and control signals (3.3V/2.5V). See page 6 for details. 3. 10ns Industrial speed grade is available in BF-208 and BC-256 packages only. 19 ns 5632 tbl 16a IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Waveform of Interrupt Timing(1) tWC (2) ADDR"A" INTERRUPT SET ADDRESS tWR (5) tAS(4) CE"A"(3) R/W"A" tINS (4) INT"B" 5632 drw 18 . tRC ADDR"B" INTERRUPT CLEAR ADDRESS tAS (2) (4) CE"B"(3) OE"B" tINR (4) INT"B" 5632 drw 19 . NOTES: 1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”. 2. Refer to Interrupt Truth Table. 3. CEX = VIL means CE0X = VIL and CE1X = VIH. CEX = VIH means CE0X = VIH and/or CE1X = VIL. 4. Timing depends on which enable signal (CE or R/W) is asserted last. 5. Timing depends on which enable signal (CE or R/W) is de-asserted first. Truth Table III — Interrupt Flag(1,4) Left Port R/WL L X X X CEL L X X L OEL X X X L Right Port (5) A17L-A0L 3FFFF INTL X R/WR X CER X OER X A17R-A0R(5) X INTR Function (2) Set Right INTR Flag (3) L X X X L L 3FFFF H Reset Right INTR Flag X (3) L L X 3FFFE X Set Left INTL Flag (2) X X X X X Reset Left INTL Flag 3FFFE L H NOTES: 1. Assumes BUSYL = BUSYR =VIH. CE0X = VIL and CE1X = VIH. 2. If BUSYL = VIL, then no change. 3. If BUSYR = VIL, then no change. 4. INTL and INTR must be initialized at power-up. 5. A17x is a NC for IDT70T659. Therefore, Interrupt Addresses are 1FFFF and 1FFFE. 20 5632 tbl 17 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Truth Table IV — Address BUSY Arbitration Inputs Outputs (4) CEL(5) CER(5) AOL-A17L AOR-A17R BUSYL(1) BUSYR(1) Function X X NO MATCH H H Normal H X MATCH H H Normal X H MATCH H H Normal L L MATCH (2) (2) Write Inhibit(3) 5632 tbl 18 NOTES: 1. Pins BUSYL and BUSYR are both outputs when the part is configured as a master. Both are inputs when configured as a slave. BUSY outputs on the IDT70T651/9 are push-pull, not open drain outputs. On slaves the BUSY input internally inhibits writes. 2. "L" if the inputs to the opposite port were stable prior to the address and enable inputs of this port. "H" if the inputs to the opposite port became stable after the address and enable inputs of this port. If tAPS is not met, either BUSYL or BUSYR = LOW will result. BUSYL and BUSYR outputs can not be LOW simultaneously. 3. Writes to the left port are internally ignored when BUSYL outputs are driving LOW regardless of actual logic level on the pin. Writes to the right port are internally ignored when BUSYR outputs are driving LOW regardless of actual logic level on the pin. 4. A17 is a NC for IDT70T659. Address comparison will be for A0 - A16. 5. CEX = L means CE0X = VIL and CE1X = VIH. CEX = H means CE0X = VIH and/or CE1X = VIL. Truth Table V — Example of Semaphore Procurement Sequence(1,2,3) Functions D0 - D35 Left D0 - D35 Right Status No Action 1 1 Semaphore free Left Port Writes "0" to Semaphore 0 1 Left port has semaphore token Right Port Writes "0" to Semaphore 0 1 No change. Right side has no write access to semaphore Left Port Writes "1" to Semaphore 1 0 Right port obtains semaphore token Left Port Writes "0" to Semaphore 1 0 No change. Left port has no write access to semaphore Right Port Writes "1" to Semaphore 0 1 Left port obtains semaphore token Left Port Writes "1" to Semaphore 1 1 Semaphore free Right Port Writes "0" to Semaphore 1 0 Right port has semaphore token Right Port Writes "1" to Semaphore 1 1 Semaphore free Left Port Writes "0" to Semaphore 0 1 Left port has semaphore token Left Port Writes "1" to Semaphore 1 1 Semaphore free NOTES: 1. This table denotes a sequence of events for only one of the eight semaphores on the IDT70T651/9. 2. There are eight semaphore flags written to via I/O0 and read from all I/O's (I/O0-I/O35). These eight semaphores are addressed by A0 - A2. 3. CE = VIH, SEM = VIL to access the semaphores. Refer to the Semaphore Read/Write Control Truth Table. Functional Description 5632 tbl 19 box or message center) is assigned to each port. The left port interrupt flag (INTL) is asserted when the right port writes to memory location 3FFFE (HEX), where a write is defined as CER = R/WR = VIL per the Truth Table. The left port clears the interrupt through access of address location 3FFFE when CEL = OEL = VIL, R/W is a "don't care". Likewise, the right port interrupt flag (INTR) is asserted when the left port writes to memory location 3FFFF (HEX) and to clear the interrupt flag (INTR), the right port must read the memory location 3FFFF. The message (36 bits) at 3FFFE or 3FFFF (1FFFF or 1FFFE for IDT70T659) is user-defined since it is an addressable SRAM location. If the interrupt function is not used, address locations 3FFFE and 3FFFF are not used The IDT70T651/9 provides two ports with separate control, address and I/O pins that permit independent access for reads or writes to any location in memory. The IDT70T651/9 has an automatic power down feature controlled by CE. The CE0 and CE1 control the on-chip power down circuitry that permits the respective port to go into a standby mode when not selected (CE = HIGH). When a port is enabled, access to the entire memory array is permitted. Interrupts If the user chooses the interrupt function, a memory location (mail 21 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM as mail boxes, but as part of the random access memory. Refer to Truth Table III for the interrupt operation. The BUSY arbitration on a master is based on the chip enable and address signals only. It ignores whether an access is a read or write. In a master/slave array, both address and chip enable must be valid long enough for a BUSY flag to be output from the master before the actual write pulse can be initiated with the R/W signal. Failure to observe this timing can result in a glitched internal write inhibit signal and corrupted data in the slave. Busy Logic Busy Logic provides a hardware indication that both ports of the RAM have accessed the same location at the same time. It also allows one of the two accesses to proceed and signals the other side that the RAM is “Busy”. The BUSY pin can then be used to stall the access until the operation on the other side is completed. If a write operation has been attempted from the side that receives a BUSY indication, the write signal is gated internally to prevent the write from proceeding. The use of BUSY logic is not required or desirable for all applications. In some cases it may be useful to logically OR the BUSY outputs together and use any BUSY indication as an interrupt source to flag the event of an illegal or illogical operation. If the write inhibit function of BUSY logic is not desirable, the BUSY logic can be disabled by placing the part in slave mode with the M/S pin. Once in slave mode the BUSY pin operates solely as a write inhibit input pin. Normal operation can be programmed by tying the BUSY pins HIGH. If desired, unintended write operations can be prevented to a port by tying the BUSY pin for that port LOW. The BUSY outputs on the IDT70T651/9 RAM in master mode, are push-pull type outputs and do not require pull up resistors to operate. Semaphores The IDT70T651/9 is an extremely fast Dual-Port 256/128K x 36 CMOS Static RAM with an additional 8 address locations dedicated to binary semaphore flags. These flags allow either processor on the left or right side of the Dual-Port RAM to claim a privilege over the other processor for functions defined by the system designer’s software. As an example, the semaphore can be used by one processor to inhibit the other from accessing a portion of the Dual-Port RAM or any other shared resource. The Dual-Port RAM features a fast access time, with both ports being completely independent of each other. This means that the activity on the left port in no way slows the access time of the right port. Both ports are identical in function to standard CMOS Static RAM and can be read from or written to at the same time with the only possible conflict arising from the simultaneous writing of, or a simultaneous READ/WRITE of, a non-semaphore location. Semaphores are protected against such ambiguous situations and may be used by the system program to avoid any conflicts in the non-semaphore portion of the Dual-Port RAM. These devices have an automatic power-down feature controlled by CE0 and CE1, the Dual-Port RAM chip enables, and SEM, the semaphore enable. The CE0, CE1, and SEM pins control onchip power down circuitry that permits the respective port to go into standby mode when not selected. Systems which can best use the IDT70T651/9 contain multiple processors or controllers and are typically very high-speed systems which are software controlled or software intensive. These systems can benefit from a performance increase offered by the IDT70T651/9s hardware semaphores, which provide a lockout mechanism without requiring complex programming. Software handshaking between processors offers the maximum in system flexibility by permitting shared resources to be allocated in varying configurations. The IDT70T651/9 does not use its semaphore flags to control any resources through hardware, thus allowing the system designer total flexibility in system architecture. An advantage of using semaphores rather than the more common methods of hardware arbitration is that wait states are never incurred in either processor. This can prove to be a major advantage in very high-speed systems. A18 CE0 MASTER Dual Port RAM BUSYL BUSYR CE0 SLAVE Dual Port RAM BUSYL BUSYR CE1 MASTER Dual Port RAM CE1 SLAVE Dual Port RAM BUSYL BUSYL BUSYR BUSYR 5632 drw 20 Industrial and Commercial Temperature Ranges . Figure 3. Busy and chip enable routing for both width and depth expansion with IDT70T651/9 Dual-Port RAMs. If these RAMs are being expanded in depth, then the BUSY indication for the resulting array requires the use of an external AND gate. Width Expansion with Busy Logic Master/Slave Arrays When expanding an IDT70T651/9 RAM array in width while using BUSY logic, one master part is used to decide which side of the RAMs array will receive a BUSY indication, and to output that indication. Any number of slaves to be addressed in the same address range as the master use the BUSY signal as a write inhibit signal. Thus on the IDT70T651/9 RAM the BUSY pin is an output if the part is used as a master (M/S pin = VIH), and the BUSY pin is an input if the part used as a slave (M/S pin = VIL) as shown in Figure 3. If two or more master parts were used when expanding in width, a split decision could result with one master indicating BUSY on one side of the array and another master indicating BUSY on one other side of the array. This would inhibit the write operations from one port for part of a word and inhibit the write operations from the other port for the other part of the word. How the Semaphore Flags Work The semaphore logic is a set of eight latches which are independent of the Dual-Port RAM. These latches can be used to pass a flag, or token, from one port to the other to indicate that a shared resource is in use. The semaphores provide a hardware assist for a use assignment method called “Token Passing Allocation.” In this method, the state of a semaphore latch is used as a token indicating that a shared resource is in use. If the left processor wants to use this resource, it requests the token by setting the latch. This processor then 22 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges the gap between the read and write cycles. It is important to note that a failed semaphore request must be followed by either repeated reads or by writing a one into the same location. The reason for this is easily understood by looking at the simple logic diagram of the semaphore flag in Figure 4. Two semaphore request latches feed into a semaphore flag. Whichever latch is first to present a zero to the semaphore flag will force its side of the semaphore flag LOW and the other side HIGH. This condition will continue until a one is written to the same semaphore request latch. If the opposite side semaphore request latch has been written to zero in the meantime, the semaphore flag will flip over to the other side as soon as a one is written into the first request latch. The opposite side flag will now stay LOW until its semaphore request latch is written to a one. From this it is easy to verifies its success in setting the latch by reading it. If it was successful, it proceeds to assume control over the shared resource. If it was not successful in setting the latch, it determines that the right side processor has set the latch first, has the token and is using the shared resource. The left processor can then either repeatedly request that semaphore’s status or remove its request for that semaphore to perform another task and occasionally attempt again to gain control of the token via the set and test sequence. Once the right side has relinquished the token, the left side should succeed in gaining control. The semaphore flags are active LOW. A token is requested by writing a zero into a semaphore latch and is released when the same side writes a one to that latch. The eight semaphore flags reside within the IDT70T651/9 in a separate memory space from the Dual-Port RAM. This address space is accessed by placing a low input on the SEM pin (which acts as a chip select for the semaphore flags) and using the other control pins (Address, CE0, CE1,R/W and BEn) as they would be used in accessing a standard Static RAM. Each of the flags has a unique address which can be accessed by either side through address pins A0 – A2. When accessing the semaphores, none of the other address pins has any effect. When writing to a semaphore, only data pin D0 is used. If a low level is written into an unused semaphore location, that flag will be set to a zero on that side and a one on the other side (see Truth Table V). That semaphore can now only be modified by the side showing the zero. When a one is written into the same location from the same side, the flag will be set to a one for both sides (unless a semaphore request from the other side is pending) and then can be written to by both sides. The fact that the side which is able to write a zero into a semaphore subsequently locks out writes from the other side is what makes semaphore flags useful in interprocessor communications. (A thorough discussion on the use of this feature follows shortly.) A zero written into the same location from the other side will be stored in the semaphore request latch for that side until the semaphore is freed by the first side. When a semaphore flag is read, its value is spread into all data bits so that a flag that is a one reads as a one in all data bits and a flag containing a zero reads as all zeros for a semaphore read, the SEM, BEn, and OE signals need to be active. (Please refer to Truth Table II). Furthermore, the read value is latched into one side’s output register when that side's semaphore select (SEM, BEn) and output enable (OE) signals go active. This serves to disallow the semaphore from changing state in the middle of a read cycle due to a write cycle from the other side. A sequence WRITE/READ must be used by the semaphore in order to guarantee that no system level contention will occur. A processor requests access to shared resources by attempting to write a zero into a semaphore location. If the semaphore is already in use, the semaphore request latch will contain a zero, yet the semaphore flag will appear as one, a fact which the processor will verify by the subsequent read (see Table V). As an example, assume a processor writes a zero to the left port at a free semaphore location. On a subsequent read, the processor will verify that it has written successfully to that location and will assume control over the resource in question. Meanwhile, if a processor on the right side attempts to write a zero to the same semaphore flag it will fail, as will be verified by the fact that a one will be read from that semaphore on the right side during subsequent read. Had a sequence of READ/WRITE been used instead, system contention problems could have occurred during L PORT R PORT SEMAPHORE REQUEST FLIP FLOP D0 WRITE D Q SEMAPHORE REQUEST FLIP FLOP Q SEMAPHORE READ Figure 4. IDT70T651/9 Semaphore Logic D D0 WRITE SEMAPHORE READ 5632 drw 21 understand that, if a semaphore is requested and the processor which requested it no longer needs the resource, the entire system can hang up until a one is written into that semaphore request latch. The critical case of semaphore timing is when both sides request a single token by attempting to write a zero into it at the same time. The semaphore logic is specially designed to resolve this problem. If simultaneous requests are made, the logic guarantees that only one side receives the token. If one side is earlier than the other in making the request, the first side to make the request will receive the token. If both requests arrive at the same time, the assignment will be arbitrarily made to one port or the other. One caution that should be noted when using semaphores is that semaphores alone do not guarantee that access to a resource is secure. As with any powerful programming technique, if semaphores are misused or misinterpreted, a software error can easily happen. Initialization of the semaphores is not automatic and must be handled via the initialization program at power-up. Since any semaphore request flag which contains a zero must be reset to a one, all semaphores on both sides should have a one written into them at initialization from both sides to assure that they will be free when needed. 23 24 VALIDDATA VALIDADDRESS NOTES: 1. CE1 = V IH. 2. All timing is same for Left and Right ports. IDD DATA ADDRESS ZZ CE0 Normal Operation tZZS tZZPD No newreads or writes allowed Timing Waveform of Sleep Mode(1,2) IZZ Sleep Mode tZZPU tZZR No reads or writes allowed , 5632 drw22 Normal Operation IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Sleep Mode The IDT70T651/9 is equipped with an optional sleep or low power mode on both ports. The sleep mode pin on both ports is active high. During normal operation, the ZZ pin is pulled low. When ZZ is pulled high, the port will enter sleep mode where it will meet lowest possible power conditions. The sleep mode timing diagram shows the modes of operation: Normal Operation, No Read/Write Allowed and Sleep Mode. For a period of time prior to sleep mode and after recovering from sleep mode (tZZS and tZZR), new reads or writes are not allowed. If a write or read operation occurs during these periods, the memory array may be corrupted. Validity of data out from the RAM cannot be guaranteed immediately after ZZ is asserted (prior to being in sleep). During sleep mode the RAM automatically deselects itself. The RAM disconnects its internal buffer. All outputs will remain in high-Z state while in sleep mode. All inputs are allowed to toggle. The RAM will not be selected and will not perform any reads or writes. JTAG Timing Specifications tJF tJCL tJCYC tJR tJCH TCK Device Inputs(1)/ TDI/TMS tJS Device Outputs(2)/ TDO tJDC tJH tJRSR tJCD TRST x 5632 drw 23 tJRST NOTES: 1. Device inputs = All device inputs except TDI, TMS, TCK and TRST. 2. Device outputs = All device outputs except TDO. JTAG AC Electrical Characteristics(1,2,3,4,5) 70T651/9 Symbol Parameter Min. Max. Units tJCYC JTAG Clock Input Period 100 ____ ns tJCH JTAG Clock HIGH 40 ____ ns tJCL JTAG Clock Low 40 ____ ns (1) tJR JTAG Clock Rise Time ____ 3 ns tJF JTAG Clock Fall Time ____ 3(1) ns tJRST JTAG Reset 50 ____ ns tJRSR JTAG Reset Recovery 50 ____ ns tJCD JTAG Data Output ____ 25 ns tJDC JTAG Data Output Hold 0 ____ ns tJS JTAG Setup 15 ____ ns tJH JTAG Hold 15 ____ ns NOTES: 1. Guaranteed by design. 2. 30pF loading on external output signals. 3. Refer to AC Electrical Test Conditions stated earlier in this document. 4. JTAG operations occur at one speed (10MHz). The base device may run at any speed specified in this datasheet. 5. JTAG cannot be tested in sleep mode. 5632 tbl 20 25 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Identification Register Definitions Instruction Field Value Revision Number (31:28) Description 0x0 IDT Device ID (27:12) 0x338(1) IDT JEDEC ID (11:1) 0x33 ID Register Indicator Bit (Bit 0) Reserved for version number Defines IDT part number 70T651 Allows unique identification of device vendor as IDT 1 Indicates the presence of an ID register 5632 tbl 21 NOTE: 1. Device ID for IDT70T659 is 0x339. Scan Register Sizes Register Name Bit Size Instruction (IR) 4 Bypass (BYR) 1 Identification (IDR) Boundary Scan (BSR) 32 Note (3) 5632 tbl 22 System Interface Parameters Instruction Code Description EXTEST 0000 Forces contents of the boundary scan cells onto the device outputs (1). Places the boundary scan register (BSR) between TDI and TDO. BYPASS 1111 Places the bypass register (BYR) between TDI and TDO. IDCODE 0010 Loads the ID register (IDR) with the vendor ID code and places the register between TDI and TDO. 0100 Places the bypass register (BYR) between TDI and TDO. Forces all device output drivers to a High-Z state. HIGHZ CLAMP 0011 SAMPLE/PRELOAD 0001 RESERVED Uses BYR. Forces contents of the boundary scan cells onto the device outputs. Places the bypass register (BYR) between TDI and TDO. Places the boundary scan register (BSR) between TDI and TDO. SAMPLE allows data from device inputs (2) and outputs (1) to be captured in the boundary scan cells and shifted serially through TDO. PRELOAD allows data to be input serially into the boundary scan cells via the TDI. Several combinations are reserved. Do not use codes other than those identified above. All Other Codes NOTES: 1. Device outputs = All device outputs except TDO. 2. Device inputs = All device inputs except TDI, TMS, TCK and TRST. 3. The Boundary Scan Descriptive Language (BSDL) file for this device is available on the IDT website (www.idt.com), or by contacting your local IDT sales representative. 26 5632 tbl 23 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges Ordering Information XXXXX A 999 A Device Type Power Speed Package A A A Process/ Temperature Range Blank 8 Tube of Tray Tape and Reel Blank I(3) Commercial (0°C to +70°C) Industrial (-40°C to +85°C) G(2) Green BC DR BF 256-pin BGA (BC-256) 208-pin PQFP (DR-208) 208-pin fpBGA (BF-208) 10 12 15 Commercial & Industrial(1) Commercial & Industrial Commercial Only S Standard Power 70T651 70T659 9Mbit (256K x 36) Asynchronous Dual-Port RAM 4Mbit (128K x 36) Asynchronous Dual-Port RAM Speed in nanoseconds 5632 drw 24 NOTES: 1. 10ns Industrial speed grade is available in BF-208 and BC-256 packages only. 2. Green parts available. For specific speeds, packages and powers contact your local sales office. 3. Contact your local sales office for additional industrial temp range speeds, packages and powers. DA TASHEET DOCUMENT HIST OR Y DAT HISTOR ORY 04/25/03: 10/01/03: 10/20/03: 04/21/04: 01/05/06: Page 9 Page 9 Page 9, 11, 15, 17 & 26 Page 10 Page 11, 15 & 17 Page 11 Page 12 Page 14 Page 1 & 25 Page 1, 14 & 15 Page 15 Page 1 Page 27 Initial Datasheet Added 8ns speed DC power numbers to DC Electrical Characteristics Table Updated DC power numbers for 10, 12 & 15ns speeds in the DC Electrical Characteristics Table Added footnote that indicates that 8ns speed is available in BF-208 and BC-256 packages only Added Capacitance Derating Drawing Added 8ns AC timing numbers to the AC Electrical Characteristics Tables Added tSOE and tLZOB to the AC Read Cycle Electrical Characteristics Table Added tLZOB to the Waveform of Read Cycles Drawing Added tSOE to Timing Waveform of Semaphore Read after Write Timing, Either Side Drawing Added 8ns speed grade and 10ns I-temp to features and to ordering information Added RapidWrite Mode Write Cycle text and waveforms Corrected tARF to 1.5V/ns Min. Removed Preliminary status from entire datasheet Added green availability to features Added green indicator to ordering information 27 IDT70T651/9S High-Speed 2.5V 256/128K x 36 Asynchronous Dual-Port Static RAM Industrial and Commercial Temperature Ranges DA TASHEET DOCUMENT HIST OR Y ((con't con't DAT HISTOR ORY con't)) 07/25/08: 01/19/09: 06/22/15: 07/20/15: Page 9 Page 27 Page 2 , 3 & 4 Page 27 Page 1 Page 9 Page 11 & 17 Page 27 Corrected a typo in the DC Chars table Removed "IDT" from orderable part number Removed the date from all of the pin configurations BC-256, DR-208 & BF-208 Added T&R indicator and updated footnotes to Ordering Information Updated the commercial speed offering by removing the 8ns speed Removed commercial 8ns speed from DC Elec Chars table and edited footnotes to reflect this change Removed commercial 8ns speed from all AC Elec Chars tables and edited footnotes to reflect this change Removed commercial 8ns speed offering from the Ordering Information CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. 28 for Tech Support: 408-284-2794 [email protected]