TI1 INA214CIDCKR Voltage output, low- or high-side measurement, bidirectional Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
INA21x Voltage Output, Low- or High-Side Measurement, Bidirectional,
Zero-Drift Series, Current-Shunt Monitors
1 Features
3 Description
•
•
The INA210, INA211, INA212, INA213, INA214, and
INA215 are voltage-output, current-shunt monitors
(also called current-sense amplifiers) that are
commonly used for overcurrent protection, precisioncurrent measurement for system optimization, or in
closed-loop feedback circuits. This series of devices
can sense drops across shunts at common-mode
voltages from –0.3 V to 26 V, independent of the
supply voltage. Six fixed gains are available: 50 V/V,
75 V/V, 100 V/V, 200 V/V, 500 V/V, or 1000 V/V. The
low offset of the zero-drift architecture enables
current sensing with maximum drops across the
shunt as low as 10-mV full-scale.
1
•
•
•
•
Wide Common-Mode Range: –0.3 V to +26 V
Offset Voltage: ±35 μV (Max, INA210)
(Enables Shunt Drops of 10-mV Full-Scale)
Accuracy:
– ±1% Gain Error (Max Over Temperature)
– 0.5-μV/°C Offset Drift (Max)
– 10-ppm/°C Gain Drift (Max)
Choice of Gains:
– INA210: 200 V/V
– INA211: 500 V/V
– INA212: 1000 V/V
– INA213: 50 V/V
– INA214: 100 V/V
– INA215: 75 V/V
Quiescent Current: 100 μA (max)
SC70 and Thin UQFN Packages: All Models
These devices operate from a single 2.7-V to 26-V
power supply, drawing a maximum of 100 µA of
supply current. All versions are specified over the
extended operating temperature range (–40°C to
125°C), and offered in SC70 and UQFN packages.
Device Information(1)
PART NUMBER
2 Applications
•
•
•
•
•
INA21x
Notebook Computers
Cell Phones
Telecom Equipment
Power Management
Battery Chargers
PACKAGE
BODY SIZE (NOM)
SC70 (6)
2.00 mm × 1.25 mm
UQFN (10)
1.80 mm × 1.40 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Simplified Schematic
REF
GND
2.7 V to 26 V
CBYPASS
0.01 mF
to
0.1 mF
RSHUNT
Supply
Reference
Voltage
INA21x
Output
OUT
R1
R3
R2
R4
IN-
IN+
V+
SC70
Load
PRODUCT
GAIN
R3 and R4
R1 and R2
INA210
INA211
INA212
INA213
INA214
INA215
200
500
1000
50
100
75
5 kW
2 kW
1 kW
20 kW
10 kW
13.3 kW
1 MW
1 MW
1 MW
1 MW
1 MW
1 MW
VOUT = (ILOAD ´ RSHUNT) Gain + VREF
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Options.......................................................
Pin Configurations and Functions .......................
Specifications.........................................................
1
1
1
2
5
5
6
7.1
7.2
7.3
7.4
7.5
7.6
6
6
7
7
7
9
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description ............................................ 13
8.1 Overview ................................................................. 13
8.2 Functional Block Diagram ....................................... 13
8.3 Feature Description................................................. 14
8.4 Device Functional Modes........................................ 15
9
Application and Implementation ........................ 21
9.1 Application Information............................................ 21
9.2 Typical Applications ................................................ 21
10 Power Supply Recommendations ..................... 24
11 Layout................................................................... 24
11.1 Layout Guidelines ................................................. 24
11.2 Layout Example .................................................... 24
12 Device and Documentation Support ................. 25
12.1
12.2
12.3
12.4
12.5
12.6
12.7
Documentation Support ........................................
Related Links ........................................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
25
25
25
25
25
25
25
13 Mechanical, Packaging, and Orderable
Information ........................................................... 26
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision H (June 2016) to Revision I
•
Page
Deleted all notes regarding preview devices throughout data sheet; all devices now active................................................. 1
Changes from Revision G (July 2014) to Revision H
Page
•
Changed Features section: deleted last bullet, changed packages bullet ............................................................................ 1
•
Deleted last Applications bullet .............................................................................................................................................. 1
•
Changed Description section.................................................................................................................................................. 1
•
Changed Device Information table ........................................................................................................................................ 1
•
Changed Device Options table: added INA211B and INA212B RSW rows, added INA215B rows, and added footnote ..... 5
•
Moved storage temperature to Absolute Maximum Ratings table ........................................................................................ 6
•
Changed ESD Ratings table: changed title, changed format to current standards ............................................................... 6
•
Changed HBM specification for version A and B devices in ESD Ratings table .................................................................. 6
•
Deleted both Machine Model rows from ESD Ratings table ................................................................................................. 6
•
Changed first sentence referencing Equation 1 in Input Filtering section: replaced seen with measured .......................... 15
•
Changed second sentence referencing Equation 1 in Input Filtering section ..................................................................... 16
•
Corrected punctuation and added clarity to first and second paragraphs in Shutting Down the INA210-INA215
Series section ...................................................................................................................................................................... 17
•
Changed impressed to present in fourth paragraph of Shutting Down the INA210-INA215 Series section ........................ 17
Changes from Revision F (June 2014) to Revision G
Page
•
Changed Simplified Schematic: added equation below gain table......................................................................................... 1
•
Changed V(ESD) HBM specifications for version A in Handling Ratings table......................................................................... 6
2
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
Changes from Revision E (June 2013) to Revision F
Page
•
Changed format to meet latest data sheet standards; added Pin Functions, Recommended Operating Conditions,
and Thermal Information tables, Overview, Functional Block Diagram, Application Information, Power Supply
Recommendations, and Layout sections, and moved existing sections ................................................................................ 1
•
Added INA215 to document .................................................................................................................................................. 1
•
Added INA215 sub-bullet to fourth Features bullet ............................................................................................................... 1
•
Added INA215 to simplified schematic table ......................................................................................................................... 1
•
Changed title of Device Options table ................................................................................................................................... 5
•
Added Thermal Information table ........................................................................................................................................... 6
•
Added INA215 to Figure 7 ...................................................................................................................................................... 9
•
Added INA215 to Figure 15 .................................................................................................................................................. 10
•
Added INA215 to Figure 25 .................................................................................................................................................. 17
Changes from Revision D (November 2012) to Revision E
•
Page
Deleted Package Marking column from Package/Ordering Information table........................................................................ 5
Changes from Revision C (August 2012) to Revision D
•
Page
Changed Frequency Response, Bandwidth parameter in Electrical Characteristics table .................................................... 6
Changes from Revision B (June 2009) to Revision C
Page
•
Changed Package/Ordering table to show both silicon versions A and B ............................................................................. 5
•
Added silicon version B row to Input, Common-Mode Input Range parameter in Electrical Characteristics table................ 6
•
Added silicon version B ESD ratings to Abs Max table.......................................................................................................... 6
•
Corrected typo in Figure 9 ..................................................................................................................................................... 9
•
Updated Figure 12 ................................................................................................................................................................. 9
•
Changed Input Filtering section............................................................................................................................................ 15
•
Added Improving Transient Robustness section .................................................................................................................. 20
Changes from Revision A (June 2008) to Revision B
Page
•
Added RSW package to device photo.................................................................................................................................... 1
•
Added UQFN package to Features list................................................................................................................................... 1
•
Updated front page graphic .................................................................................................................................................... 1
•
Added RSW ordering information to Package/Ordering Information table............................................................................. 5
•
Added RSW package pin out drawing.................................................................................................................................... 5
•
Added footnote 3 to Electrical Characteristics table............................................................................................................... 6
•
Added UQFN package information to Temperature Range section of Electrical Characteristics table ................................. 6
•
Changed Figure 2 to reflect operating temperature range ..................................................................................................... 9
•
Changed Figure 4 to reflect operating temperature range ..................................................................................................... 9
•
Changed Figure 6 to reflect operating temperature range ..................................................................................................... 9
•
Changed Figure 13 to reflect operating temperature range ................................................................................................. 10
•
Changed Figure 14 to reflect operating temperature range ................................................................................................. 10
•
Added RSW description to the Basic Connections section .................................................................................................. 14
•
Changed 60μV to 100μV in last sentence of the Selecting RS section................................................................................ 14
Copyright © 2008–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
3
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
Changes from Original (May 2008) to Revision A
Page
•
Changed availability of INA211 and INA212 to currently available in Package/Ordering Information table .......................... 5
•
Deleted first footnote of Electrical Characteristics table ......................................................................................................... 6
•
Changed Figure 7 .................................................................................................................................................................. 9
•
Changed Figure 15 .............................................................................................................................................................. 10
4
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
5 Device Options
PRODUCT
GAIN (V/V)
PACKAGE
PACKAGE
DESIGNATOR
200
SC70-6
DCK
200
Thin UQFN-10
RSW
200
SC70-6
DCK
200
Thin UQFN-10
RSW
500
SC70-6
DCK
INA210A
INA210B
INA211A
INA211B
INA212A
INA212B
INA213A
INA213B
INA214A
INA214B
INA215A
INA215B
500
SC70-6
DCK
500
Thin UQFN-10
RSW
1000
SC70-6
DCK
1000
SC70-6
DCK
1000
Thin UQFN-10
RSW
50
SC70-6
DCK
50
Thin UQFN-10
RSW
50
SC70-6
DCK
50
Thin UQFN-10
RSW
100
SC70-6
DCK
100
Thin UQFN-10
RSW
100
SC70-6
DCK
100
Thin UQFN-10
RSW
75
SC70-6
DCK
75
Thin UQFN-10
RSW
75
SC70-6
DCK
6 Pin Configurations and Functions
DCK Package
6-Pin SC70
Top View
RSW Package
10-Pin Thin UQFN
Top View
NC
REF
1
6
OUT
GND
2
5
IN-
V+
3
4
IN+
REF
8
GND
9
OUT
10
7
V+
6
1
NC
(1)
(1)
(1)
2
5
IN-
4
IN-
3
IN+
IN+
NC denotes no internal connection. These pins can be left floating or connected to any voltage between V– and V+.
Copyright © 2008–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
5
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
Pin Functions
PIN
NAME
NO.
I/O
DESCRIPTION
DCK
RSW
GND
2
9
Analog
Ground
IN–
5
4, 5
Analog
input
Connect to load side of shunt resistor.
IN+
4
2, 3
Analog
input
Connect to supply side of shunt resistor
NC
—
1, 7
—
Output voltage
Not internally connected. Leave floating or connect to ground.
OUT
6
10
Analog
output
REF
1
8
Analog
input
Reference voltage, 0 V to V+
V+
3
6
Analog
Power supply, 2.7 V to 26 V
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
Supply voltage, VS
Differential (VIN+) – (VIN–)
Analog inputs, VIN+, VIN– (2)
Common-mode (3)
REF input
Output
(3)
(1)
(2)
(3)
V
–26
26
V
26
V
GND – 0.3
(VS) + 0.3
V
GND – 0.3
(VS) + 0.3
V
5
mA
150
°C
150
°C
150
°C
–55
Junction temperature
Storage temperature, Tstg
UNIT
26
GND – 0.3
Input current into any terminal (3)
Operating temperature
MAX
–65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
VIN+ and VIN– are the voltages at the IN+ and IN– terminals, respectively.
Input voltage at any terminal may exceed the voltage shown if the current at that terminal is limited to 5 mA.
7.2 ESD Ratings
VALUE
UNIT
INA21x, Version A
V(ESD)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±4000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±1000
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±3500
V
INA21x, Version B
V(ESD)
(1)
(2)
6
Electrostatic discharge
Charged-device model (CDM), per JEDEC specification JESD22-C101
(2)
±1000
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
VCM
Common-mode input voltage
VS
Operating supply voltage
TA
Operating free-air temperature
NOM
MAX
UNIT
12
V
5
V
–40
125
°C
7.4 Thermal Information
INA210-INA215
THERMAL METRIC (1)
DCK (SC70)
RSW (UQFN)
UNIT
6 PINS
10 PINS
RθJA
Junction-to-ambient thermal resistance
227.3
107.3
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
79.5
56.5
°C/W
RθJB
Junction-to-board thermal resistance
72.1
18.7
°C/W
ψJT
Junction-to-top characterization parameter
3.6
1.1
°C/W
ψJB
Junction-to-board characterization parameter
70.4
18.7
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
n/a
n/a
°C/W
(1)
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
7.5 Electrical Characteristics
At TA = 25°C, VSENSE = VIN+ – VIN–.
INA210, INA213, INA214, and INA215: VS = 5 V, VIN+ = 12 V, and VREF = VS / 2, unless otherwise noted.
INA211 and INA212: VS = 12 V, VIN+ = 12 V, and VREF = VS / 2, unless otherwise noted.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
INPUT
Version A, TA = –40°C to 125°C
–0.3
26
Version B, TA = –40°C to 125°C
–0.1
26
INA210, INA211,
INA212, INA214,
INA215
VIN+ = 0 V to 26 V, VSENSE = 0 mV,
TA = –40°C to 125°C
105
INA213
VIN+ = 0 V to 26 V, VSENSE = 0 mV,
TA = –40°C to 125°C
100
INA210, INA211,
INA212
VSENSE = 0 mV
±0.55
±35
INA213
VSENSE = 0 mV
±5
±100
INA214, INA215
VCM
Common-mode input range
CMRR
Common-mode
rejection ratio
V
140
dB
120
(1)
VO
Offset voltage, RTI
VSENSE = 0 mV
±1
±60
dVOS/dT
RTI vs temperature
VSENSE = 0 mV, TA = –40°C to 125°C
0.1
0.5
µV/°C
PSRR
RTI vs power supply ratio
VS = 2.7 V to 18 V, VIN+ = 18 V,
VSENSE = 0 mV
±0.1
±10
µV/V
IIB
Input bias current
VSENSE = 0 mV
28
35
µA
IIO
Input offset current
VSENSE = 0 mV
15
µV
±0.02
µA
OUTPUT
INA210
G
EG
(1)
Gain
200
INA211
500
INA212
1000
INA213
50
INA214
100
INA215
75
Gain error
VSENSE = –5 mV to 5 mV,
TA = –40°C to 125°C
Gain error vs temperature
TA = –40°C to 125°C
Nonlinearity error
VSENSE = –5 mV to 5 mV
Maximum capacitive load
No sustained oscillation
V/V
±0.02%
±1%
3
10
ppm/°C
±0.01%
1
nF
RTI = referred-to-input.
Copyright © 2008–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
7
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
Electrical Characteristics (continued)
At TA = 25°C, VSENSE = VIN+ – VIN–.
INA210, INA213, INA214, and INA215: VS = 5 V, VIN+ = 12 V, and VREF = VS / 2, unless otherwise noted.
INA211 and INA212: VS = 12 V, VIN+ = 12 V, and VREF = VS / 2, unless otherwise noted.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
VOLTAGE OUTPUT (2)
Swing to V+ power-supply rail
RL = 10 kΩ to GND, TA = –40°C to
125°C
(V+) – 0.05
(V+) – 0.2
V
Swing to GND
RL = 10 kΩ to GND, TA = –40°C to
125°C
(VGND) + 0.005
(VGND) + 0.05
V
FREQUENCY RESPONSE
BW
Bandwidth
CLOAD = 10 pF, INA210
14
CLOAD = 10 pF, INA211
7
CLOAD = 10 pF, INA212
4
CLOAD = 10 pF, INA213
80
CLOAD = 10 pF, INA214
30
CLOAD = 10 pF, INA215
SR
kHz
40
Slew rate
0.4
V/µs
25
nV/√Hz
NOISE, RTI (1)
Voltage noise density
POWER SUPPLY
VS
Operating voltage range
TA = –40°C to 125°C
IQ
Quiescent current
VSENSE = 0 mV
IQ over temperature
TA = –40°C to 125°C
2.7
65
26
V
100
µA
115
µA
°C
TEMPERATURE RANGE
θJA
(2)
8
Specified range
–40
125
Operating range
–55
150
Thermal resistance
SC70
Thin UQFN
°C
250
°C/W
80
°C/W
See Typical Characteristic curve, Output Voltage Swing vs Output Current (Figure 10).
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
7.6 Typical Characteristics
The INA210 is used for typical characteristics at TA = 25°C, VS = 5 V, VIN+ = 12 V, and VREF = VS / 2, unless otherwise noted.
100
80
Population
Offset Voltage (mV)
60
40
20
0
-20
-40
-60
30
35
20
25
10
15
5
0
-5
-10
-15
-20
-25
-30
-35
-80
-100
-50
-25
0
Offset Voltage (mV)
25
50
75
100
125
150
Temperature (°C)
Figure 2. Offset Voltage vs Temperature
Figure 1. Input Offset Voltage Production Distribution
5
4
Population
CMRR (mV/V)
3
2
1
0
-1
-2
-3
-4
-5.0
-4.5
-4.0
-3.5
-3.0
-2.5
-2.0
-1.5
-1.0
-0.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
-5
-50
-25
0
25
50
75
100
125
150
Temperature (°C)
Common-Mode Rejection Ratio (mV/V)
Figure 4. Common-Mode Rejection Ratio vs Temperature
Figure 3. Common-Mode Rejection Production Distribution
1.0
20 Typical Units Shown
0.8
Population
Gain Error (%)
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-1.0
-0.9
-0.8
-0.7
-0.6
-0.5
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
-0.8
Gain Error (%)
Figure 5. Gain Error Production Distribution
Copyright © 2008–2016, Texas Instruments Incorporated
-1.0
-50
-25
0
25
50
75
100
125
150
Temperature (°C)
Figure 6. Gain Error vs Temperature
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
9
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
Typical Characteristics (continued)
The INA210 is used for typical characteristics at TA = 25°C, VS = 5 V, VIN+ = 12 V, and VREF = VS / 2, unless otherwise noted.
160
70
INA211
60
140
50
120
|PSRR| (dB)
Gain (dB)
INA212
40
30
INA213
INA210
INA214
20
INA215
10
100
10k
100k
1M
1
10M
Output Voltage Swing (V)
|CMRR| (dB)
60
VS = +5V
VCM = 1V Sine
VDIF = Shorted
VREF = 2.5V
100
1k
10k
100k
V+
(V+) - 0.5
(V+) - 1
(V+) - 1.5
(V+) - 2
(V+) - 2.5
(V+) - 3
VS = 2.7V
to 26V
VS = 2.7V
GND + 3
GND + 2.5
GND + 2
GND + 1.5
GND + 1
GND + 0.5
GND
1M
TA = -40C
TA = +25C
TA = +125C
VS = 2.7V to 26V
0
5
10
15
20
25
30
35
40
Output Current (mA)
Figure 9. Common-Mode Rejection Ratio vs Frequency
Figure 10. Output Voltage Swing vs Output Current
30
50
25
40
IB+, IB-, VREF = 0V
Input Bias Current (mA)
Input Bias Current (mA)
100k
VS = 5V to 26V
Frequency (Hz)
30
20
IB+, IB-, VREF = 2.5V
10
0
IB+, IB-, VREF = 0V
and
IB-, VREF = 2.5V
20
15
10
5
IB+, VREF = 2.5V
0
-10
-5
0
10
10k
Figure 8. Power-Supply Rejection Ratio vs Frequency
80
10
1k
Figure 7. Gain vs Frequency
100
1
100
Frequency (Hz)
120
0
10
Frequency (Hz)
140
20
VS = +5V + 250mV Sine Disturbance
VCM = 0V
VDIF = Shorted
VREF = 2.5V
0
1k
160
40
60
20
-10
10
80
40
VCM = 0V
VDIF = 15mVPP Sine
0
100
5
10
15
20
25
30
0
5
10
15
20
25
30
Common-Mode Voltage (V)
Common-Mode Voltage (V)
Figure 11. Input Bias Current vs Common-Mode Voltage
with Supply Voltage = 5 V
Figure 12. Input Bias Current vs Common-Mode Voltage
with Supply Voltage = 0 V (Shutdown)
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
Typical Characteristics (continued)
The INA210 is used for typical characteristics at TA = 25°C, VS = 5 V, VIN+ = 12 V, and VREF = VS / 2, unless otherwise noted.
35
100
90
Quiescent Current (mA)
Input Bias Current (mA)
30
25
20
15
10
5
70
60
50
40
30
20
10
-25
0
25
50
75
100
125
0
25
50
75
100
125
150
Temperature (°C)
Figure 13. Input Bias Current vs Temperature
Figure 14. Quiescent Current vs Temperature
INA213
INA215
INA212
INA214
INA210
INA211
10
VS = ±2.5V
VREF = 0V
VIN-, VIN+ = 0V
10
-25
Temperature (°C)
100
1
0
-50
150
100
1k
10k
Referred-to-Input
Voltage Noise (200nV/div)
0
-50
Input-Reffered Voltage Noise (nV/Öz)
80
VS = ±2.5V
VCM = 0V
VDIF = 0V
VREF = 0V
Time (1s/div)
100k
Frequency (Hz)
10mVPP Input Signal
Time (100ms/div)
Figure 17. Step Response (10-mVPP Input Step)
Copyright © 2008–2016, Texas Instruments Incorporated
Common-Mode Voltage (1V/div)
Input Voltage
(5mV/diV)
2VPP Output Signal
Figure 16. 0.1-Hz to 10-Hz Voltage Noise (Referred-To-Input)
Common Voltage Step
0V
Output Voltage
0V
Output Voltage (40mV/div)
Output Voltage
(0.5V/diV)
Figure 15. Input-Referred Voltage Noise vs Frequency
Time (50ms/div)
Figure 18. Common-Mode Voltage Transient Response
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
11
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
Typical Characteristics (continued)
The INA210 is used for typical characteristics at TA = 25°C, VS = 5 V, VIN+ = 12 V, and VREF = VS / 2, unless otherwise noted.
Noninverting Input Overload
2V/div
2V/div
Inverting Input Overload
Output
Output
0V
0V
VS = 5V, VCM = 12V, VREF = 2.5V
VS = 5V, VCM = 12V, VREF = 2.5V
Time (250ms/div)
Time (250ms/div)
Figure 19. Inverting Differential Input Overload
Figure 20. Noninverting Differential Input Overload
Supply Voltage
1V/div
1V/div
Supply Voltage
Output Voltage
Output Voltage
0V
VS = 5V, 1kHz Step with VDIFF = 0V, VREF = 2.5V
12
0V
VS = 5V, 1kHz Step with VDIFF = 0V, VREF = 2.5V
Time (100ms/div)
Time (100ms/div)
Figure 21. Start-Up Response
Figure 22. Brownout Recovery
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
8 Detailed Description
8.1 Overview
The INA210-INA215 are 26-V, common-mode, zero-drift topology, current-sensing amplifiers that can be used in
both low-side and high-side configurations. These specially-designed, current-sensing amplifiers are able to
accurately measure voltages developed across current-sensing resistors on common-mode voltages that far
exceed the supply voltage powering the device. Current can be measured on input voltage rails as high as 26 V
while the device can be powered from supply voltages as low as 2.7 V.
The zero-drift topology enables high-precision measurements with maximum input offset voltages as low as
35 µV with a maximum temperature contribution of 0.5 µV/°C over the full temperature range of –40°C to 125°C.
8.2 Functional Block Diagram
V+
IN-
OUT
IN+
+
REF
GND
Copyright © 2008–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
13
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
8.3 Feature Description
8.3.1 Basic Connections
Figure 23 shows the basic connections of the INA210-INA215. Connect the input pins (IN+ and IN–) as closely
as possible to the shunt resistor to minimize any resistance in series with the shunt resistor.
RSHUNT
Power
Supply
Load
5V Supply
CBYPASS
0.1µF
V+
IN-
-
OUT
+
IN+
ADC
Microcontroller
REF
GND
Figure 23. Typical Application
Power-supply bypass capacitors are required for stability. Applications with noisy or high-impedance power
supplies may require additional decoupling capacitors to reject power-supply noise. Connect bypass capacitors
close to the device pins.
On the RSW package options, two pins are provided for each input. Tie these pins together (that is, tie IN+ to
IN+ and tie IN– to IN–).
8.3.2 Selecting RS
The zero-drift offset performance of the INA210-INA215 offers several benefits. Most often, the primary
advantage of the low offset characteristic enables lower full-scale drops across the shunt. For example, nonzero-drift current shunt monitors typically require a full-scale range of 100 mV.
The INA210-INA215 series gives equivalent accuracy at a full-scale range on the order of 10 mV. This accuracy
reduces shunt dissipation by an order of magnitude with many additional benefits.
Alternatively, there are applications that must measure current over a wide dynamic range that can take
advantage of the low offset on the low end of the measurement. Most often, these applications can use the lower
gains of the INA213, INA214, or INA215 to accommodate larger shunt drops on the upper end of the scale. For
instance, an INA213 operating on a 3.3-V supply can easily handle a full-scale shunt drop of 60 mV, with only
100 μV of offset.
14
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
8.4 Device Functional Modes
8.4.1 Input Filtering
An obvious and straightforward filtering location is at the device output. However, this location negates the
advantage of the low output impedance of the internal buffer. The only other filtering option is at the device input
pins. This location, though, does require consideration of the ±30% tolerance of the internal resistances.
Figure 24 shows a filter placed at the inputs pins.
V+
VCM
RS < 10W
RINT
VOUT
RSHUNT
CF
Bias
RS < 10W
VREF
RINT
Load
Figure 24. Filter at Input Pins
The addition of external series resistance, however, creates an additional error in the measurement so the value
of these series resistors must be kept to 10 Ω (or less, if possible) to reduce impact to accuracy. The internal
bias network shown in Figure 24 present at the input pins creates a mismatch in input bias currents when a
differential voltage is applied between the input pins. If additional external series filter resistors are added to the
circuit, the mismatch in bias currents results in a mismatch of voltage drops across the filter resistors. This
mismatch creates a differential error voltage that subtracts from the voltage developed at the shunt resistor. This
error results in a voltage at the device input pins that is different than the voltage developed across the shunt
resistor. Without the additional series resistance, the mismatch in input bias currents has little effect on device
operation. The amount of error these external filter resistors add to the measurement can be calculated using
Equation 2 where the gain error factor is calculated using Equation 1.
The amount of variance in the differential voltage present at the device input relative to the voltage developed at
the shunt resistor is based both on the external series resistance value as well as the internal input resistors, R3
and R4 (or RINT as shown in Figure 24). The reduction of the shunt voltage reaching the device input pins
appears as a gain error when comparing the output voltage relative to the voltage across the shunt resistor. A
factor can be calculated to determine the amount of gain error that is introduced by the addition of external series
resistance. The equation used to calculate the expected deviation from the shunt voltage to what is measured at
the device input pins is given in Equation 1:
(1250 ´ RINT)
Gain Error Factor =
(1250 ´ RS) + (1250 ´ RINT) + (RS ´ RINT)
where:
•
•
RINT is the internal input resistor (R3 and R4), and
RS is the external series resistance.
Copyright © 2008–2016, Texas Instruments Incorporated
(1)
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
15
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
Device Functional Modes (continued)
With the adjustment factor from Equation 1, including the device internal input resistance, this factor varies with
each gain version, as shown in Table 1. Each individual device gain error factor is shown in Table 2.
Table 1. Input Resistance
PRODUCT
GAIN
RINT (kΩ)
INA210
200
5
INA211
500
2
INA212
1000
1
INA213
50
20
INA214
100
10
INA215
75
13.3
Table 2. Device Gain Error Factor
PRODUCT
SIMPLIFIED GAIN ERROR FACTOR
INA210
1000
RS + 1000
10,000
INA211
(13 ´ RS) + 10,000
5000
INA212
(9 ´ RS) + 5000
20,000
INA213
(17 ´ RS) + 20,000
10,000
INA214
(9 ´ RS) + 10,000
8,000
INA215
(7 x RS) + 8,000
The gain error that can be expected from the addition of the external series resistors can then be calculated
based on Equation 2:
Gain Error (%) = 100 - (100 ´ Gain Error Factor)
(2)
For example, using an INA212 and the corresponding gain error equation from Table 2, a series resistance of
10 Ω results in a gain error factor of 0.982. The corresponding gain error is then calculated using Equation 2,
resulting in a gain error of approximately 1.77% solely because of the external 10-Ω series resistors. Using an
INA213 with the same 10-Ω series resistor results in a gain error factor of 0.991 and a gain error of 0.84% again
solely because of these external resistors.
16
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
8.4.2 Shutting Down the INA210-INA215 Series
Although the INA210-INA215 series does not have a shutdown pin, the low power consumption of the device
allows the output of a logic gate or transistor switch to power the INA210-INA215. This gate or switch turns on
and turns off the INA210-INA215 power-supply quiescent current.
However, in current shunt monitoring applications, there is also a concern for how much current is drained from
the shunt circuit in shutdown conditions. Evaluating this current drain involves considering the simplified
schematic of the INA210-INA215 in shutdown mode, as shown in Figure 25.
Shutdown
Control
RSHUNT
Supply
Reference
Voltage
REF
INA21x
GND
1 MW
R3
1 MW
R4
Load
Output
OUT
IN-
IN+
V+
CBYPASS
PRODUCT
R3 and R4
INA210
INA211
INA212
INA213
INA214
INA215
5 kW
2 kW
1 kW
20 kW
10 kW
13.3 kW
NOTE: 1-MΩ paths from shunt inputs to reference and INA21x outputs.
Figure 25. Basic Circuit for Shutting Down the INA210-INA215 with a Grounded Reference
Note that there is typically slightly more than 1-MΩ impedance (from the combination of 1-MΩ feedback and
5-kΩ input resistors) from each input of the INA210-INA215 to the OUT pin and to the REF pin. The amount of
current flowing through these pins depends on the respective ultimate connection. For example, if the REF pin is
grounded, the calculation of the effect of the 1-MΩ impedance from the shunt to ground is straightforward.
However, if the reference or op amp is powered while the INA210-INA215 is shut down, the calculation is direct;
instead of assuming 1 MΩ to ground, however, assume 1 MΩ to the reference voltage. If the reference or op
amp is also shut down, some knowledge of the reference or op amp output impedance under shutdown
conditions is required. For instance, if the reference source behaves as an open circuit when not powered, little
or no current flows through the 1-MΩ path.
Regarding the 1-MΩ path to the output pin, the output stage of a disabled INA210-INA215 does constitute a
good path to ground. Consequently, this current is directly proportional to a shunt common-mode voltage present
across a 1-MΩ resistor.
As a final note, when the device is powered up, there is an additional, nearly constant, and well-matched 25 μA
that flows in each of the inputs as long as the shunt common-mode voltage is 3 V or higher. Below 2-V commonmode, the only current effects are the result of the 1-MΩ resistors.
Copyright © 2008–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
17
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
8.4.3 REF Input Impedance Effects
As with any difference amplifier, the INA210-INA215 series common-mode rejection ratio is affected by any
impedance present at the REF input. This concern is not a problem when the REF pin is connected directly to
most references or power supplies. When using resistive dividers from the power supply or a reference voltage,
the REF pin must be buffered by an op amp.
In systems where the INA210-INA215 output can be sensed differentially, such as by a differential input analogto-digital converter (ADC) or by using two separate ADC inputs, the effects of external impedance on the REF
input can be cancelled. Figure 26 depicts a method of taking the output from the INA210-INA215 by using the
REF pin as a reference.
RSHUNT
Supply
Load
ADC
REF
GND
+2.7 V to +26 V
Device
OUT
R1
R3
R2
R4
Output
IN-
IN+
V+
CBYPASS
0.01 mF
to
0.1 mF
Figure 26. Sensing the INA210-INA215 to Cancel the Effects of Impedance on the REF Input
8.4.4 Using The INA210-INA215 with Common-Mode Transients Above 26 V
With a small amount of additional circuitry, the INA210-INA215 series can be used in circuits subject to transients
higher than 26 V, such as automotive applications. Use only zener diode or zener-type transient absorbers
(sometimes referred to as Transzorbs)—any other type of transient absorber has an unacceptable time delay.
Start by adding a pair of resistors as a working impedance for the zener; see Figure 27. Keeping these resistors
as small as possible is preferable, most often around 10 Ω. Larger values can be used with an effect on gain that
is discussed in the Input Filtering section. Because this circuit limits only short-term transients, many applications
are satisfied with a 10-Ω resistor along with conventional zener diodes of the lowest power rating that can be
found. This combination uses the least amount of board space. These diodes can be found in packages as small
as SOT-523 or SOD-523.
18
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
RSHUNT
Supply
RPROTECT
10 W
Load
RPROTECT
10 W
Reference
Voltage
REF
Device
GND
1 MW
R3
1 MW
R4
V+
Shutdown
Control
Output
OUT
IN-
IN+
CBYPASS
Figure 27. INA210-INA215 Transient Protection using Dual Zener Diodes
In the event that low-power zeners do not have sufficient transient absorption capability and a higher power
transzorb must be used, the most package-efficient solution then involves using a single transzorb and back-toback diodes between the device inputs. The most space-efficient solutions are dual series-connected diodes in a
single SOT-523 or SOD-523 package. This method is shown in Figure 28. In either of these examples, the total
board area required by the INA210-INA215 with all protective components is less than that of an SO-8 package,
and only slightly greater than that of an MSOP-8 package.
RSHUNT
Supply
RPROTECT
10 W
Load
RPROTECT
10 W
Reference
Voltage
REF
Device
GND
1 MW
R3
1 MW
R4
OUT
V+
Shutdown
Control
Output
IN-
IN+
CBYPASS
Figure 28. INA210-INA215 Transient Protection using a Single Transzorb and Input Clamps
Copyright © 2008–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
19
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
8.4.5 Improving Transient Robustness
Applications involving large input transients with excessive dV/dt above 2 kV per microsecond present at the
device input pins may cause damage to the internal ESD structures on version A devices. This potential damage
is a result of the internal latching of the ESD structure to ground when this transient occurs at the input. With
significant current available in most current-sensing applications, the large current flowing through the input
transient-triggered, ground-shorted ESD structure quickly results in damage to the silicon. External filtering can
be used to attenuate the transient signal prior to reaching the inputs to avoid the latching condition. Care must be
taken to ensure that external series input resistance does not significantly impact gain error accuracy. For
accuracy purposes, keep these resistances under 10 Ω if possible. Ferrite beads are recommended for this filter
because of their inherently low dc ohmic value. Ferrite beads with less than 10 Ω of resistance at dc and over
600 Ω of resistance at 100 MHz to 200 MHz are recommended. The recommended capacitor values for this filter
are between 0.01 µF and 0.1 µF to ensure adequate attenuation in the high-frequency region. This protection
scheme is shown in Figure 29.
Shunt
Reference
Voltage
Load
Supply
Device
OUT
REF
1MW
R3
GND
IN-
-
+
MMZ1608B601C
IN+
V+
+2.7V to +26V
0.01mF
to 0.1mF
Output
1MW
R4
0.01mF
to 0.1mF
Figure 29. Transient Protection
To minimize the cost of adding these external components to protect the device in applications where large
transient signals may be present, version B devices are now available with new ESD structures that are not
susceptible to this latching condition. Version B devices are incapable of sustaining these damage-causing
latched conditions so they do not have the same sensitivity to the transients that the version A devices have,
thus making the version B devices a better fit for these applications.
20
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The INA210-INA215 measure the voltage developed across a current-sensing resistor when current passes
through it. The ability to drive the reference pin to adjust the functionality of the output signal offers multiple
configurations, as discussed throughout this section.
9.2 Typical Applications
9.2.1 Unidirectional Operation
Bus Supply
Load
Power Supply
CBYPASS
0.1µF
V+
IN-
-
OUT
Output
+
IN+
REF
GND
Figure 30. Unidirectional Application Schematic
9.2.1.1 Design Requirements
The device can be configured to monitor current flowing in one direction (unidirectional) or in both directions
(bidirectional) depending on how the REF pin is configured. The most common case is unidirectional where the
output is set to ground when no current is flowing by connecting the REF pin to ground, as shown in Figure 30.
When the input signal increases, the output voltage at the OUT pin increases.
9.2.1.2 Detailed Design Procedure
The linear range of the output stage is limited in how close the output voltage can approach ground under zero
input conditions. In unidirectional applications where measuring very low input currents is desirable, bias the REF
pin to a convenient value above 50 mV to get the output into the linear range of the device. To limit commonmode rejection errors, TI recommends buffering the reference voltage connected to the REF pin.
A less frequently-used output biasing method is to connect the REF pin to the supply voltage, V+. This method
results in the output voltage saturating at 200 mV below the supply voltage when no differential input signal is
present. This method is similar to the output saturated low condition with no input signal when the REF pin is
connected to ground. The output voltage in this configuration only responds to negative currents that develop
negative differential input voltage relative to the device IN– pin. Under these conditions, when the differential
input signal increases negatively, the output voltage moves downward from the saturated supply voltage. The
voltage applied to the REF pin must not exceed the device supply voltage.
Copyright © 2008–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
21
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
Typical Applications (continued)
9.2.1.3 Application Curve
Output Voltage
(1 V/div)
An example output response of a unidirectional configuration is shown in Figure 31. With the REF pin connected
directly to ground, the output voltage is biased to this zero output level. The output rises above the reference
voltage for positive differential input signals but cannot fall below the reference voltage for negative differential
input signals because of the grounded reference voltage.
0V
Output
VREF
Time (500 µs /div)
C001
Figure 31. Unidirectional Application Output Response
22
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
Typical Applications (continued)
9.2.2 Bidirectional Operation
Load
Bus Supply
Power Supply
CBYPASS
0.1µF
V+
IN-
-
Reference
Voltage
Output
OUT
+
IN+
REF
+
-
GND
Figure 32. Bidirectional Application Schematic
9.2.2.1 Design Requirements
The device is a bidirectional, current-sense amplifier capable of measuring currents through a resistive shunt in
two directions. This bidirectional monitoring is common in applications that include charging and discharging
operations where the current flow-through resistor can change directions.
9.2.2.2 Detailed Design Procedure
The ability to measure this current flowing in both directions is enabled by applying a voltage to the REF pin, as
shown in Figure 32. The voltage applied to REF (VREF) sets the output state that corresponds to the zero-input
level state. The output then responds by increasing above VREF for positive differential signals (relative to the IN–
pin) and responds by decreasing below VREF for negative differential signals. This reference voltage applied to
the REF pin can be set anywhere between 0 V to V+. For bidirectional applications, VREF is typically set at midscale for equal signal range in both current directions. In some cases, however, VREF is set at a voltage other
than mid-scale when the bidirectional current and corresponding output signal do not need to be symmetrical.
9.2.2.3 Application Curve
Output Voltage
(1 V/div)
An example output response of a bidirectional configuration is shown in Figure 33. With the REF pin connected
to a reference voltage, 2.5 V in this case, the output voltage is biased upwards by this reference level. The
output rises above the reference voltage for positive differential input signals and falls below the reference
voltage for negative differential input signals.
VOUT
VREF
0V
Time (500 µs/div)
C002
Figure 33. Bidirectional Application Output Response
Copyright © 2008–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
23
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
10 Power Supply Recommendations
The input circuitry of the INA210-INA215 can accurately measure beyond its power-supply voltage, V+. For
example, the V+ power supply can be 5 V, whereas the load power-supply voltage can be as high as 26 V.
However, the output voltage range of the OUT pin is limited by the voltages on the power-supply pin. Note also
that the INA210-INA215 can withstand the full input signal range up to 26 V at the input pins, regardless of
whether the device has power applied or not.
11 Layout
11.1 Layout Guidelines
•
•
Connect the input pins to the sensing resistor using a Kelvin or 4-wire connection. This connection technique
ensures that only the current-sensing resistor impedance is detected between the input pins. Poor routing of
the current-sensing resistor commonly results in additional resistance present between the input pins. Given
the very low ohmic value of the current resistor, any additional high-current carrying impedance can cause
significant measurement errors.
Place the power-supply bypass capacitor as closely as possible to the supply and ground pins. The
recommended value of this bypass capacitor is 0.1 μF. Additional decoupling capacitance can be added to
compensate for noisy or high-impedance power supplies.
11.2 Layout Example
Output Signal
Trace
IN-
IN+
GND
V+
REF OUT
VIA to Power or
Ground Plane
VIA to Ground
Plane
Supply
Voltage
Supply Bypass
Capacitor
Figure 34. Recommended Layout
24
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
INA210, INA211, INA212, INA213, INA214, INA215
www.ti.com
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
• INA210-215EVM User's Guide (SBOU065)
12.2 Related Links
Table 3 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to sample or buy.
Table 3. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
INA210
Click here
Click here
Click here
Click here
Click here
INA211
Click here
Click here
Click here
Click here
Click here
INA212
Click here
Click here
Click here
Click here
Click here
INA213
Click here
Click here
Click here
Click here
Click here
INA214
Click here
Click here
Click here
Click here
Click here
INA215
Click here
Click here
Click here
Click here
Click here
12.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.5 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
12.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
Copyright © 2008–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
25
INA210, INA211, INA212, INA213, INA214, INA215
SBOS437I – MAY 2008 – REVISED SEPTEMBER 2016
www.ti.com
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
26
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: INA210 INA211 INA212 INA213 INA214 INA215
PACKAGE OPTION ADDENDUM
www.ti.com
11-Oct-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
INA210AIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
CET
INA210AIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
CET
INA210AIRSWR
ACTIVE
UQFN
RSW
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KNJ
INA210AIRSWT
ACTIVE
UQFN
RSW
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
(KNJ ~ NSJ)
INA210BIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SED
INA210BIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SED
INA210BIRSWR
ACTIVE
UQFN
RSW
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
SHQ
INA210BIRSWT
ACTIVE
UQFN
RSW
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
SHQ
INA210CIDCKR
PREVIEW
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
16B
INA210CIDCKT
PREVIEW
SC70
DCK
6
250
TBD
Call TI
Call TI
-40 to 125
INA210CIRSWR
PREVIEW
UQFN
RSW
10
3000
TBD
Call TI
Call TI
-40 to 125
INA210CIRSWT
PREVIEW
UQFN
RSW
10
250
Green (RoHS
& no Sb/Br)
Call TI
Level-1-260C-UNLIM
-40 to 125
16C
INA211AIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
CEU
INA211AIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
CEU
INA211BIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SEE
INA211BIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SEE
INA211BIRSWR
ACTIVE
UQFN
RSW
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
13Q
INA211BIRSWT
ACTIVE
UQFN
RSW
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
13Q
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
11-Oct-2016
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
INA211CIDCKR
PREVIEW
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
16D
INA211CIDCKT
PREVIEW
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
16D
INA212AIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
CEV
INA212AIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
CEV
INA212BIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SEC
INA212BIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SEC
INA212BIRSWR
ACTIVE
UQFN
RSW
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
13U
INA212BIRSWT
ACTIVE
UQFN
RSW
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
13U
INA212CIDCKR
PREVIEW
SC70
DCK
6
3000
TBD
Call TI
Call TI
-40 to 125
INA212CIDCKT
PREVIEW
SC70
DCK
6
250
TBD
Call TI
Call TI
-40 to 125
INA213AIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
CFT
INA213AIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
CFT
INA213AIRSWR
ACTIVE
UQFN
RSW
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KPJ
INA213AIRSWT
ACTIVE
UQFN
RSW
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KPJ
INA213BIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SEF
INA213BIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SEF
INA213BIRSWR
ACTIVE
UQFN
RSW
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
SHT
INA213BIRSWT
ACTIVE
UQFN
RSW
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
SHT
INA213CIDCKR
PREVIEW
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
16F
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
11-Oct-2016
Status
(1)
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
INA213CIDCKT
PREVIEW
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
16F
INA214AIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
CFV
INA214AIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
CFV
INA214AIRSWR
ACTIVE
UQFN
RSW
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KRJ
INA214AIRSWT
ACTIVE
UQFN
RSW
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KRJ
INA214BIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SEA
INA214BIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SEA
INA214BIRSWR
ACTIVE
UQFN
RSW
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
SHU
INA214BIRSWT
ACTIVE
UQFN
RSW
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
SHU
INA214CIDCKR
PREVIEW
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
16G
INA214CIDCKT
PREVIEW
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
16G
INA215AIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SME
INA215AIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
SME
INA215BIDCKR
ACTIVE
SC70
DCK
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
13S
INA215BIDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
13S
INA215BIRSWR
ACTIVE
UQFN
RSW
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
13R
INA215BIRSWT
ACTIVE
UQFN
RSW
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
13R
The marketing status values are defined as follows:
Addendum-Page 3
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Oct-2016
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF INA210, INA211, INA212, INA213, INA214, INA215 :
• Automotive: INA210-Q1, INA211-Q1, INA212-Q1, INA213-Q1, INA214-Q1, INA215-Q1
NOTE: Qualified Version Definitions:
Addendum-Page 4
PACKAGE OPTION ADDENDUM
www.ti.com
11-Oct-2016
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 5
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Sep-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
INA210AIDCKR
SC70
DCK
6
3000
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA210AIDCKR
SC70
DCK
6
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
INA210AIDCKT
SC70
DCK
6
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA210AIDCKT
SC70
DCK
6
250
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
INA210AIRSWR
UQFN
RSW
10
3000
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA210AIRSWT
UQFN
RSW
10
250
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA210BIDCKR
SC70
DCK
6
3000
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA210BIDCKT
SC70
DCK
6
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA210BIRSWR
UQFN
RSW
10
3000
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA210BIRSWT
UQFN
RSW
10
250
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA211AIDCKR
SC70
DCK
6
3000
180.0
8.4
2.47
2.3
1.25
4.0
8.0
Q3
INA211AIDCKT
SC70
DCK
6
250
180.0
8.4
2.47
2.3
1.25
4.0
8.0
Q3
INA211AIDCKT
SC70
DCK
6
250
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
INA211BIDCKR
SC70
DCK
6
3000
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA211BIDCKT
SC70
DCK
6
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA211BIRSWR
UQFN
RSW
10
3000
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA211BIRSWT
UQFN
RSW
10
250
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA212AIDCKR
SC70
DCK
6
3000
180.0
8.4
2.47
2.3
1.25
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Sep-2016
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
INA212BIDCKR
SC70
DCK
6
3000
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA212BIDCKT
SC70
DCK
6
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA212BIRSWR
UQFN
RSW
10
3000
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA212BIRSWT
UQFN
RSW
10
250
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA213AIDCKR
SC70
DCK
6
3000
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA213AIDCKR
SC70
DCK
6
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
INA213AIDCKT
SC70
DCK
6
250
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
INA213AIDCKT
SC70
DCK
6
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA213AIRSWR
UQFN
RSW
10
3000
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA213AIRSWT
UQFN
RSW
10
250
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA213BIDCKR
SC70
DCK
6
3000
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA213BIDCKT
SC70
DCK
6
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA213BIRSWR
UQFN
RSW
10
3000
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA213BIRSWT
UQFN
RSW
10
250
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA214AIDCKR
SC70
DCK
6
3000
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA214AIDCKR
SC70
DCK
6
3000
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
INA214AIDCKT
SC70
DCK
6
250
179.0
8.4
2.2
2.5
1.2
4.0
8.0
Q3
INA214AIDCKT
SC70
DCK
6
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA214AIRSWR
UQFN
RSW
10
3000
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA214AIRSWT
UQFN
RSW
10
250
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA214BIDCKR
SC70
DCK
6
3000
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA214BIDCKT
SC70
DCK
6
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA214BIRSWR
UQFN
RSW
10
3000
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA214BIRSWT
UQFN
RSW
10
250
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA215AIDCKR
SC70
DCK
6
3000
178.0
8.4
2.4
2.5
1.2
4.0
8.0
Q3
INA215AIDCKT
SC70
DCK
6
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA215BIDCKR
SC70
DCK
6
3000
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA215BIDCKT
SC70
DCK
6
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
INA215BIRSWR
UQFN
RSW
10
3000
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
INA215BIRSWT
UQFN
RSW
10
250
179.0
8.4
1.7
2.1
0.7
4.0
8.0
Q1
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Sep-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
INA210AIDCKR
SC70
DCK
6
3000
180.0
180.0
18.0
INA210AIDCKR
SC70
DCK
6
3000
195.0
200.0
45.0
INA210AIDCKT
SC70
DCK
6
250
180.0
180.0
18.0
INA210AIDCKT
SC70
DCK
6
250
195.0
200.0
45.0
INA210AIRSWR
UQFN
RSW
10
3000
203.0
203.0
35.0
INA210AIRSWT
UQFN
RSW
10
250
203.0
203.0
35.0
INA210BIDCKR
SC70
DCK
6
3000
180.0
180.0
18.0
INA210BIDCKT
SC70
DCK
6
250
180.0
180.0
18.0
INA210BIRSWR
UQFN
RSW
10
3000
203.0
203.0
35.0
INA210BIRSWT
UQFN
RSW
10
250
203.0
203.0
35.0
INA211AIDCKR
SC70
DCK
6
3000
223.0
270.0
35.0
INA211AIDCKT
SC70
DCK
6
250
223.0
270.0
35.0
INA211AIDCKT
SC70
DCK
6
250
195.0
200.0
45.0
INA211BIDCKR
SC70
DCK
6
3000
180.0
180.0
18.0
INA211BIDCKT
SC70
DCK
6
250
180.0
180.0
18.0
INA211BIRSWR
UQFN
RSW
10
3000
203.0
203.0
35.0
INA211BIRSWT
UQFN
RSW
10
250
203.0
203.0
35.0
INA212AIDCKR
SC70
DCK
6
3000
223.0
270.0
35.0
INA212BIDCKR
SC70
DCK
6
3000
180.0
180.0
18.0
INA212BIDCKT
SC70
DCK
6
250
180.0
180.0
18.0
Pack Materials-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Sep-2016
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
INA212BIRSWR
UQFN
RSW
10
3000
203.0
203.0
35.0
INA212BIRSWT
UQFN
RSW
10
250
203.0
203.0
35.0
INA213AIDCKR
SC70
DCK
6
3000
180.0
180.0
18.0
INA213AIDCKR
SC70
DCK
6
3000
195.0
200.0
45.0
INA213AIDCKT
SC70
DCK
6
250
195.0
200.0
45.0
INA213AIDCKT
SC70
DCK
6
250
180.0
180.0
18.0
INA213AIRSWR
UQFN
RSW
10
3000
203.0
203.0
35.0
INA213AIRSWT
UQFN
RSW
10
250
203.0
203.0
35.0
INA213BIDCKR
SC70
DCK
6
3000
180.0
180.0
18.0
INA213BIDCKT
SC70
DCK
6
250
180.0
180.0
18.0
INA213BIRSWR
UQFN
RSW
10
3000
203.0
203.0
35.0
INA213BIRSWT
UQFN
RSW
10
250
203.0
203.0
35.0
INA214AIDCKR
SC70
DCK
6
3000
180.0
180.0
18.0
INA214AIDCKR
SC70
DCK
6
3000
195.0
200.0
45.0
INA214AIDCKT
SC70
DCK
6
250
195.0
200.0
45.0
INA214AIDCKT
SC70
DCK
6
250
180.0
180.0
18.0
INA214AIRSWR
UQFN
RSW
10
3000
203.0
203.0
35.0
INA214AIRSWT
UQFN
RSW
10
250
203.0
203.0
35.0
INA214BIDCKR
SC70
DCK
6
3000
180.0
180.0
18.0
INA214BIDCKT
SC70
DCK
6
250
180.0
180.0
18.0
INA214BIRSWR
UQFN
RSW
10
3000
203.0
203.0
35.0
INA214BIRSWT
UQFN
RSW
10
250
203.0
203.0
35.0
INA215AIDCKR
SC70
DCK
6
3000
340.0
340.0
38.0
INA215AIDCKT
SC70
DCK
6
250
340.0
340.0
38.0
INA215BIDCKR
SC70
DCK
6
3000
340.0
340.0
38.0
INA215BIDCKT
SC70
DCK
6
250
340.0
340.0
38.0
INA215BIRSWR
UQFN
RSW
10
3000
203.0
203.0
35.0
INA215BIRSWT
UQFN
RSW
10
250
203.0
203.0
35.0
Pack Materials-Page 4
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated