ON NCV5701C High current igbt gate driver Datasheet

NCV5701A, NCV5701B,
NCV5701C
High Current IGBT Gate
Drivers
The NCV5701A, NCV5701B and NCV5701C are high−current,
high−performance stand−alone IGBT drivers for high power
applications that include solar inverters, motor control and
uninterruptible power supplies. The devices offer a cost−effective
solution by eliminating external output buffer. Devices protection
features include accurate Under−voltage−lockout (UVLO),
desaturation protection (DESAT) and Active Low FAULT output. The
drivers also feature an accurate 5.0 V output. The drivers are designed
to accommodate a wide voltage range of bias supplies including
unipolar and NCV5701B even bipolar voltages.
Depending on the pin configuration the devices also include Active
Miller Clamp (NCV5701A) and separate high and low (VOH and VOL)
driver outputs for system design convenience (NCV5701C).
All three available pin configuration variants have 8−pin SOIC
package.
Features
•
•
•
•
•
•
•
•
•
High Current Output (+4/−6 A) at IGBT Miller Plateau voltages
Low Output Impedance for Enhanced IGBT Driving
Short Propagation Delay with Accurate Matching
Direct Interface to Digital Isolator/Opto−coupler/Pulse Transformer
for Isolated Drive, Logic Compatibility for Non−isolated Drive
DESAT Protection with Programmable Delay
Tight UVLO Thresholds for Bias Flexibility
Wide Bias Voltage Range
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable, Grade 1
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
www.onsemi.com
MARKING
DIAGRAM
8
8
1
NCV5701X
ALYW
G
SOIC−8
D SUFFIX
CASE 751
1
NCV5701 = Specific Device Code
X
= A, B or C
A
= Assembly Location
L
= Wafer Lot
Y
= Year
W
= Work Week
G
= Pb−Free Package
PIN CONNECTIONS
1
8
2
7
3
6
4
5
VIN
VREF
FLT
DESAT
CLAMP
GND
VO
VCC
NCV5701A
1
8
2
7
3
6
4
5
VIN
VREF
FLT
DESAT
VEE
GND
VO
VCC
NCV5701B
NCV5701A Features
• Active Miller Clamp to Prevent Spurious Gate Turn−on
1
8
2
7
3
6
4
5
VIN
VREF
NCV5701B Features
• Negative Output Voltage for Enhanced IGBT Driving
FLT
DESAT
NCV5701C Features
• Separate Outputs for VOL and VOH
GND
VOL
VOH
VCC
NCV5701C
Typical Applications
•
•
•
•
•
ORDERING INFORMATION
Motor Control
Uninterruptible Power Supplies (UPS)
Automotive Power Supplies
HEV/EV Powertrain
HEV/EV PTC Heaters
© Semiconductor Components Industries, LLC, 2017
October, 2017 − Rev. 0
See detailed ordering and shipping information on page 9 of
this data sheet.
1
Publication Order Number:
NCV5701/D
NCV5701A, NCV5701B, NCV5701C
NCV5701A
VREF
DESAT
VCC
VCC
VO
CLAMP
VIN
GND
FLT
NCV5701B
VREF
DESAT
VCC
VCC
VO
VIN
GND
VEE
VEE
FLT
NCV5701C
VREF
DESAT
VCC
VCC
VOH
VOL
VIN
GND
FLT
Figure 1. Simplified Application Schematics
www.onsemi.com
2
NCV5701A, NCV5701B, NCV5701C
TSD
SET
Q
FLT
Q
S
CLR
R
NCV5701A
IDESAT-CHG
DELAY
DESAT
+
SET
VDESAT-THR
Q
S
-
R
CLR
VCC
Q
VREF
RIN-H
VO
VIN
VREF
Ï
DELAY
Bandgap
VUVLO
-
VCC
Ï
+
SET
Q
S
R
CLR
Q
-
CLAMP
+
VMC-THR
Figure 2(a). Detailed Block Diagram NCV5701A
NCV5701A
VREF
CLAMP
CLAMP
VIN
VCC
VREF
LDO
GND
Logic Unit
GND
TSD
FLT
VCC
VO
UVLO
DESAT
DESAT
VCC
Figure 2(b). Simplified Block Diagram NCV5701A
www.onsemi.com
3
NCV5701A, NCV5701B, NCV5701C
TSD
SET
Q
FLT
Q
S
CLR
R
NCV5701B
IDESAT-CHG
DELAY
DESAT
+
SET
VDESAT-THR
Q
S
-
R
CLR
VCC
Q
VREF
RIN-H
VO
VIN
VREF
Ï
DELAY
Bandgap
VUVLO
VEE
-
VCC
+
VEE
GND
Figure 3(a). Detailed Block Diagram NCV5701B
NCV5701B
VREF
VIN
VEE
VCC
LDO
GND
Logic Unit
VREF
TSD
FLT
VCC
VO
UVLO
DESAT
DESAT
VCC
Figure 3(b). Simplified Block Diagram NCV5701B
www.onsemi.com
4
NCV5701A, NCV5701B, NCV5701C
TSD
SET
Q
FLT
Q
S
CLR
R
NCV5701C
IDESAT-CHG
DELAY
DESAT
+
SET
VDESAT-THR
Q
S
-
CLR
R
VCC
Q
VREF
VOH
RIN-H
VIN
VREF
Ï
DELAY
Bandgap
VUVLO
-
VCC
+
GND
Figure 4(a). Detailed Block Diagram NCV5701C
NCV5701C
VREF
GND
VIN
VCC
LDO
VOL
Logic Unit
VREF
TSD
FLT
VCC
VOH
UVLO
DESAT
DESAT
VCC
Figure 4(b). Simplified Block Diagram NCV5701C
www.onsemi.com
5
VOL
NCV5701A, NCV5701B, NCV5701C
Table 1. PIN FUNCTION DESCRIPTION
Pin Name
No.
I/O/x
Description
VIN
1
I
Input signal to control the output. In applications which require galvanic isolation, VIN is generated at the opto output, the pulse transformer secondary or the digital isolator output. There is a
signal inversion from VIN to VO (VOH/VOL). VIN is internally clamped to 5.5 V and has a pull−
up resistor of 1 MW to ensure that an output is low in the absence of an input signal. A minimum
pulse−width is required at VIN before VO (VOH/VOL) is activated.
VREF
2
O
5 V Reference generated within the driver is brought out to this pin for external bypassing and
for powering low bias circuits (such as digital isolators).
FLT
3
O
Fault output (active low) that allows communication to the main controller that the driver has
encountered a fault condition and has deactivated the output. Capable of driving optos or digital
isolators when isolation is required. (Truth Table is provided in the datasheet to indicate conditions under which this signal is asserted.)
DESAT
4
I
Input for detecting the desaturation of IGBT due to a fault condition. A capacitor connected to
this pin allows a programmable blanking delay every ON cycle before DESAT fault is processed,
thus preventing false triggering.
VCC
5
x
Positive bias supply for the driver. The operating range for this pin is from UVLO to the maximum. A good quality bypassing capacitor is required from this pin to GND and should be placed
close to the pins for best results.
VO
(NCV5701A,
NCV5701B)
6
O
Driver output that provides the appropriate drive voltage, source and sink current to the IGBT
gate. VO is actively pulled low during start−up and under Fault conditions.
VOH
(NCV5701C)
6
O
Driver high output that provides the appropriate drive voltage and source current to the IGBT
gate.
VOL
(NCV5701C)
7
O
Driver low output that provides the appropriate drive voltage and sink current to the IGBT gate.
VOL is actively pulled low during start−up and under Fault conditions.
GND
(NCV5701A,
NCV5701B)
7
x
This pin should connect to the IGBT Emitter with a short trace. All power pin bypass capacitors
should be referenced to this pin and kept at a short distance from the pin.
GND
(NCV5701C)
8
x
This pin should connect to the IGBT Emitter with a short trace. All power pin bypass capacitors
should be referenced to this pin and kept at a short distance from the pin.
VEE
(NCV5701B)
8
x
A negative voltage with respect to GND can be applied to this pin and that will allow VO to go to
a negative voltage during OFF state. A good quality bypassing capacitor is needed from VEE to
GND. If a negative voltage is not applied or available, this pin must be connected to GND.
CLAMP
(NCV5701A)
8
I/O
Provides clamping for the IGBT gate during the off period to protect it from parasitic turn−on. To
be tied directly to IGBT gate with minimum trace length for best results.
www.onsemi.com
6
NCV5701A, NCV5701B, NCV5701C
Table 2. ABSOLUTE MAXIMUM RATINGS (Note 1)
Parameter
Differential Power Supply
Positive Power Supply
Negative Power Supply
Symbol
Minimum
Maximum
Unit
VCC−VEE (Vmax)
0
36
V
VCC−GND
−0.3
22
V
VEE−GND
−18
0.3
V
VCC + 0.3
V
Gate Output High
(VO, VOH)−GND
Gate Output Low
(VO, VOL)−GND
VEE − 0.3
VIN−GND
−0.3
5.5
V
VDESAT−GND
−0.3
VCC + 0.3
V
Input Voltage
DESAT Voltage
FLT current
Sink
Source
V
mA
IFLT−SINK
IFLT−SRC
20
25
PD
700
mW
Maximum Junction Temperature
TJ(max)
150
°C
Storage Temperature Range
TSTG
−65 to 150
°C
Power Dissipation
SO−8 package
ESD Capability, Human Body Model (Note 2)
ESDHBM
4
kV
ESD Capability, Machine Model (Note 2)
ESDMM
200
V
Moisture Sensitivity Level
MSL
1
−
Lead Temperature Soldering
Reflow (SMD Styles Only), Pb−Free Versions (Note 3)
TSLD
260
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114)
ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115)
Latchup Current Maximum Rating: ≤100 mA per JEDEC standard: JESD78, 125°C
3. For information, please refer to our Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
Table 3. THERMAL CHARACTERISTICS
Parameter
Symbol
Value
RqJA
176
Unit
°C/W
Thermal Characteristics, SOIC−8 (Note 4)
Thermal Resistance, Junction−to−Air (Note 5)
4. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
5. Values based on copper area of 100 mm2 (or 0.16 in2) of 1 oz copper thickness and FR4 PCB substrate.
Table 4. OPERATING RANGES (Note 6)
Parameter
Differential Power Supply
Symbol
Min
VCC−VEE (Vmax)
Max
Unit
30
V
Positive Power Supply
VCC
UVLO
20
V
Negative Power Supply
VEE
−15
0
V
Input Voltage
VIN
0
5
V
Input pulse width
ton
40
Ambient Temperature
TA
−40
125
°C
ns
6. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
www.onsemi.com
7
NCV5701A, NCV5701B, NCV5701C
Table 5. ELECTRICAL CHARACTERISTICS VCC = 15 V, VEE = 0 V, Kelvin GND connected to VEE. For typical values TA = 25°C,
for min/max values, TA is the operating ambient temperature range that applies, unless otherwise noted.
Parameter
Test Conditions
Symbol
Min
Pulse−Width = 150 ns, VEN = 5 V
Voltage applied to get output to go low
Voltage applied to get output to go high
Voltage applied without change in output state
VIN−H1
VIN−L1
VIN−NC
4.3
Typ
Max
Unit
LOGIC INPUT and OUTPUT
Input Threshold Voltages
High−state (Logic 1) Required
Low−state (Logic 0) Required
No state change
Input Internal Pull−Up
Resistance to VREF
Input Current
High−state
Low−state
Input Pulse−Width
No Response at the Output
Guaranteed Response at the
Output
FLT Threshold Voltage
Low State
High State
V
0.75
3.7
1.2
RIN−H
1
MW
mA
VIN−H = 4.5 V
VIN−L = 0.5 V
Voltage thresholds consistent with input
specs
IIN−H
IIN−L
1
10
ton−min1
ton−min2
10
ns
30
V
(IFLT−SINK = 15 mA)
(IFLT−SRC = 20 mA)
VFLT−L
VFLT−H
12
0.5
13.9
1.0
0.1
0.2
0.8
0.2
0.5
1.2
DRIVE OUTPUT
V
Output Low State
Isink = 200 mA, TA = 25°C
Isink = 200 mA, TA = −40°C to 125°C
Isink = 1.0 A, TA = 25°C
VOL1
VOL2
VOL3
Isrc = 200 mA, TA = 25°C
Isrc = 200 mA, TA = −40°C to 125°C
Isrc = 1.0 A, TA = 25°C
VOH1
VOH2
VOH3
Peak Driver Current, Sink
(Note 7)
RG = 0.1 W, VCC = 15 V, VEE = −8 V
VO = 13 V
VO = 9 V (near Miller Plateau)
IPK−snk1
IPK−snk2
6.8
6.1
Peak Driver Current, Source
(Note 7)
RG = 0.1 W, VCC = 15 V, VEE = −8 V
VO = −5 V
VO = 9 V (near Miller Plateau)
IPK−src1
IPK−src2
7.8
4.0
Output High State
V
14.5
14.2
13.8
14.8
14.7
14.1
A
A
DYNAMIC CHARACTERISTICS
Turn−on Delay
(see timing diagram)
Negative input pulse width = 10 ms
tpd−on
45
56
75
ns
Turn−off Delay
(see timing diagram)
Positive input pulse width = 10 ms
tpd−off
45
63
75
ns
Propagation Delay Distortion
(=tpd−on− tpd−off)
For input or output pulse width > 150 ns,
TA = 25°C
TA = −40°C to 125°C
tdistort1
tdistort2
−15
−25
−7
5
25
tdistort −tot
−30
0
30
Prop Delay Distortion between
Parts (Note 7)
ns
ns
Rise Time (Note 7)
(see timing diagram)
Cload = 1.0 nF
trise
9.2
ns
Fall Time (Note 7)
(see timing diagram)
Cload = 1.0 nF
tfall
7.9
ns
Delay from FLT under UVLO/
TSD to VO/VOL
td1−OUT
7. Values based on design and/or characterization.
www.onsemi.com
8
9
12
15
ms
NCV5701A, NCV5701B, NCV5701C
Table 5. ELECTRICAL CHARACTERISTICS VCC = 15 V, VEE = 0 V, Kelvin GND connected to VEE. For typical values TA = 25°C,
for min/max values, TA is the operating ambient temperature range that applies, unless otherwise noted.
Parameter
Test Conditions
Symbol
Min
Typ
Max
Unit
DYNAMIC CHARACTERISTICS
Delay from DESAT to VO/VOL
(Note 7)
td2−OUT
220
ns
Delay from UVLO/TSD to FLT
(Note 7)
td3−FLT
7.3
ms
Vclamp
1.2
1.4
2.2
V
MILLER CLAMP (NCV5701A ONLY)
Isink = 500 mA, TA = 25°C
Isink = 500 mA, TA = −40°C to 125°C
Clamp Voltage
Clamp Activation Threshold
VMC−THR
1.8
2.0
2.2
V
DESAT Threshold Voltage
VDESAT−THR
6.0
6.35
7.0
V
Blanking Charge Current
IDESAT−CHG
0.20
0.24
0.28
mA
Blanking Discharge Current
IDESAT−DIS
DESAT PROTECTION
30
mA
UVLO
UVLO Startup Voltage
VUVLO−OUT−ON
13.2
13.5
13.8
V
UVLO Disable Voltage
VUVLO−OUT−OFF
12.2
12.5
12.8
V
UVLO Hysteresis
VUVLO−HYST
1.0
V
VREF
Voltage Reference
IREF = 10 mA
VREF
Reference Output Current
(Note 7)
4.85
5.00
5.15
V
20
mA
IREF
Recommended Capacitance
CVREF
100
nF
SUPPLY CURRENT
Current Drawn from VCC
VCC = 15 V
Standby (No load on output, FLT, VREF)
ICC−SB
Current Drawn from VEE
(NCV5701B ONLY)
VEE = −10 V
Standby (No load on output, FLT, VREF)
IEE−SB
0.9
−0.2
1.5
mA
−0.14
mA
THERMAL SHUTDOWN
Thermal Shutdown Temperature
(Note 7)
TSD
188
°C
Thermal Shutdown Hysteresis
(Note 7)
TSH
33
°C
7. Values based on design and/or characterization.
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
ORDERING INFORMATION
Package
Shipping†
NCV5701ADR2G
SOIC−8
(Pb−Free)
2500 / Tape & Reel
NCV5701BDR2G
SOIC−8
(Pb−Free)
2500 / Tape & Reel
NCV5701CDR2G
SOIC−8
(Pb−Free)
2500 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
9
NCV5701A, NCV5701B, NCV5701C
TYPICAL CHARACTERISTICS
PROPAGATION DELAY (ns)
80
70
tpd−off
60
tpd−on
50
40
−40
−20
0
20
40
60
80
120
100
TEMPERATURE (°C)
Figure 5. Propagation Delay vs. Temperature
20
13
12
15
tfall
10
trise
5
11
10
−40
IO (A)
RISE/FALL TIME (ns)
14
−20
0
20
40
60
80
100
0
−40
120
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 6. Fault to Output Low Delay
Figure 7. Output Rise/Fall Time
8
8
7
7
6
6
5
5
4
3
2
2
1
1
0
5
10
0
−5
15
0
5
10
VO (V, VCC = 15 V, VEE = −8 V)
VO (V, VCC = 15 V, VEE = −8 V)
Figure 8. Output Source Current vs. Output
Voltage
Figure 9. Output Sink Current vs. Output
Voltage
www.onsemi.com
10
120
4
3
0
−5
−20
TEMPERATURE (°C)
IO (A)
FAULT TO OUTPUT DELAY (ms)
15
15
NCV5701A, NCV5701B, NCV5701C
5.05
5.05
5.04
5.04
5.03
5.03
5.02
5.02
5.01
5.01
VREF (V)
VREF (V)
TYPICAL CHARACTERISTICS
5.00
4.99
4.98
4.97
4.97
4.96
4.95
4.96
4.95
−40
2
4
6
8
10
VREF @ IREF = 10 mA
−20
0
20
40
60
80
100
IREF (mA)
TEMPERATURE (°C)
Figure 10. VREF Voltage vs. Current
Figure 11. VREF Voltage vs. Temperature
120
6.5
VDESAT (V)
260
IDESET−CHG (mA)
5.00
4.99
4.98
0
250
6.4
6.3
240
−40
−20
0
20
40
60
80
100
6.2
−40
120
−20
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 12. DESAT Charge Current vs.
Temperature
Figure 13. DESAT Threshold Voltage vs.
Temperature
15
120
20
15
10
VO (V)
VO, OUTPUT VOLTAGE (V)
VREF @ IREF = 0 mA
UVLO−OUT−OFF
UVLO−OUT−ON
10
5
5
0
0
−5
10
11
12
13
14
15
0
1
2
3
VCC, SUPPLY VOLTAGE (V)
VIN (V)
Figure 14. UVLO Threshold Voltages
Figure 15. VO vs. VIN at 255C
(VCC = 15 V, VEE = 0 V)
www.onsemi.com
11
4
5
NCV5701A, NCV5701B, NCV5701C
TYPICAL CHARACTERISTICS
1.0
VFLT−L (V)
VFLT−H (V)
15
14
13
−40
−20
0
20
40
60
80
100
0.5
0
−40
120
−20
0
20
80
100
TEMPERATURE (°C)
Figure 16. Fault Output, Sourcing 20 mA
Figure 17. Fault Output, Sinking 15 mA
120
1.4
SUPPLY CURRENT (mA)
1.2
2.0
VCLAMP (V)
60
TEMPERATURE (°C)
2.5
1.5
1.0
ICC
1.0
0.8
0.6
0.4
IEE (NCV5701B Only)
0.2
0.5
−40
40
0
−20
0
20
40
60
80
100
120
0
20
40
60
80
TEMPERATURE (°C)
FREQUENCY (kHz)
Figure 18. VCLAMP at 0.5 A (NCV5701A Only)
Figure 19. Supply Current vs. Switching
Frequency (VCC = 15 V, VEE = −10 V, 255C)
www.onsemi.com
12
100
NCV5701A, NCV5701B, NCV5701C
Applications and Operating Information
This section lists the details about key features and
operating guidelines for the NCV5701.
High Drive Current Capability
The NCV5701 driver family is equipped with many
features which facilitate a superior performance IGBT
driving circuit. Foremost amongst these features is the high
drive current capability. The drive current of an IGBT driver
is a function of the differential voltage on the output pin
(VCC−VOH/VO for source current, VOL/VO−VEE for sink
current) as shown in Figure 20. Figure 20 also indicates that
for a given VOH/VOL value, the drive current can be
increased by using higher VCC/VEE power supply). The
drive current tends to drop off as the output voltage goes up
(for turn−on event) or goes down (for turn−off event). As
explained in many IGBT application notes, the most critical
phase of IGBT switching event is the Miller plateau region
where the gate voltage remains constant at a voltage
(typically in 9−11 V range depending on IGBT design and
the collector current), but the gate drive current is used to
charge/discharge the Miller capacitance (CGC). By
providing a high drive current in this region, a gate driver can
significantly reduce the duration of the phase and help
reducing the switching losses. The NCV5701 addresses this
requirement by providing and specifying a high drive
current in the Miller plateau region. Most other gate driver
ICs merely specify peak current at the start of switching –
which may be a high number, but not very relevant to the
application requirement. It must be remembered that other
considerations such as EMI, diode reverse recovery
performance, etc., may lead to a system level decision to
trade off the faster switching speed against low EMI and
reverse recovery. However, the use of NCV5701 does not
preclude this trade−off as the user can always tune the drive
current by employing external series gate resistor. Important
thing to remember is that by providing a high internal drive
current capability, the NCV5701 facilitates a wide range of
gate resistors. Another value of the high current at the Miller
plateau is that the initial switching transition phase is shorter
and more controlled. Finally, the high gate driver current
(which is facilitated by low impedance internal FETs),
ensures that even at high switching frequencies, the power
dissipation from the drive circuit is primarily in the external
series resistor and more easily manageable. Experimental
results have shown that the high current drive results in
reduced turn−on energy (EON) for the IGBT switching.
Figure 20. Output Current vs. Output Voltage Drop
When driving larger IGBTs for higher current
applications, the drive current requirement is higher, hence
lower RG is used. Larger IGBTs typically have high input
capacitance. On the other hand, if the NCV5701 is used to
drive smaller IGBT (lower input capacitance), the drive
current requirement is lower and a higher RG is used. Thus,
for most typical applications, the driver load RC time
constant remains fairly constant. Caution must be exercised
when using the NCV5701 with a very low load RC time
constant. Such a load may trigger internal protection
circuitry within the driver and disable the device. Figure 21
shows the recommended minimum gate resistance as a
function of IGBT gate capacitance and gate drive trace
inductance.
Figure 21. Recommended Minimum Gate Resistance
as a Function of IGBT Gate Capacitance
www.onsemi.com
13
NCV5701A, NCV5701B, NCV5701C
Gate Voltage Range
controller to initiate a more orderly/sequenced shutdown. In
case the controller fails to do so, the driver output shutdown
ensures IGBT protection after td1−OUT.
The negative drive voltage for gate (with respect to GND,
or Emitter of the IGBT) is a robust way to ensure that the gate
voltage does not rise above the threshold voltage due to the
Miller effect. In systems where the negative power supply is
available, the VEE option offered by NCV5701B allows not
only a robust operation, but also a higher drive current for
turn−off transition. Adequate bypassing between VEE pin
and GND pin is essential if this option is used.
The VCC range for the NCV5701 is quite wide and allows
the user the flexibility to optimize the performance or use
available power supplies for convenience.
Under Voltage Lock Out (UVLO)
This feature ensures reliable switching of the IGBT
connected to the driver output. At the start of the driver’s
operation when VCC is applied to the driver, the output
remains turned−off. This is regardless of the signals on VIN
until the VCC reaches the UVLO Output Enabled
(VUVLO−OUT−ON) level. After the VCC rises above the
VUVLO−OUT−ON level, the driver is in normal operation. The
state of the output is controlled by signal at VIN.
If the VCC falls below the UVLO Output Disabled
(VUVLO−OUT−OFF) level during the normal operation of the
driver, the Fault output is activated and the output is shut−down
(after a delay) and remains in this state. The driver output
does not start to react to the input signal on VIN until the VCC
rises above the VUVLO−OUT−ON again. The waveform
showing the UVLO behavior of the driver is in Figure 22.
In an IGBT drive circuit, the drive voltage level is
important for drive circuit optimization. If VUVLO−OUT−OFF
is too low, it will lead to IGBT being driven with insufficient
gate voltage. A quick review of IGBT characteristics can
reveal that driving IGBT with low voltage (in 10−12 V
range) can lead to a significant increase in conduction loss.
So, it is prudent to guarantee VUVLO−OUT−OFF at a
reasonable level (above 12 V), so that the IGBT is not forced
to operate at a non−optimum gate voltage. On the other hand,
having a very high drive voltage ends up increasing
switching losses without much corresponding reduction in
conduction loss. So, the VUVLO−OUT−ON value should not
be too high (generally, well below 15 V). These conditions
lead to a tight band for UVLO enable and disable voltages,
while guaranteeing a minimum hysteresis between the two
values to prevent hiccup mode operation. The NCV5701
meets these tight requirements and ensures smooth IGBT
operation. It ensures that a 15 V supply with ±8% tolerance
will work without degrading IGBT performance, and
guarantees that a fault will be reported and the IGBT will be
turned off when the supply voltage drops below 12.2 V.
A UVLO event (VCC voltage going below VUVLO−OUT−OFF)
also triggers activation of FLT output after a delay of td3−FLT.
This indicates to the controller that the driver has
encountered an issue and corrective action needs to be taken.
However, a nominal delay td1−OUT = 12 ms is introduced
between the initiation of the FLT output and actual turning
off of the output. This delay provides adequate time for the
Figure 22. UVLO Function and Limits
Timing Delays and Impact on System Performance
The gate driver is ideally required to transmit the input
signal pulse to its output without any delay or distortion. In
the context of a high−power system where IGBTs are
typically used, relatively low switching frequency (in tens of
kHz) means that the delay through the driver itself may not
be as significant, but the matching of the delay between
different drivers in the same system as well as between
different edges has significant importance. With reference to
Figure 23(a), two input waveforms are shown. They are
typical complementary inputs for high−side (HS) and
low−side (LS) of a half−bridge switching configuration. The
dead−time between the two inputs ensures safe transition
between the two switches. However, once these inputs are
through the driver, there is potential for the actual gate
voltages for HS and LS to be quite different from the
intended input waveforms as shown in Figure 23(a). The end
result could be a loss of the intended dead−time and/or
pulse−width distortion. The pulse−width distortion can
create an imbalance that needs to be corrected, while the loss
of dead−time can eventually lead to cross−conduction of the
switches and additional power losses or damage to the
system.
The NCV5701 driver is designed to address these timing
challenges by providing a very low pulse−width distortion
and excellent delay matching. As an example, the delay
matching is guaranteed to tDISTORT2 = ±25 ns while many
of competing driver solutions can be >250 ns.
www.onsemi.com
14
NCV5701A, NCV5701B, NCV5701C
Figure 23(a). Timing Waveforms (Other Drivers)
Figure 23(b). NCV5701 Timing Waveforms
Active Miller Clamp Protection
An alternative way is to provide an additional path from
gate to GND with very low impedance. This is exactly what
Active Miller Clamp protection does. Additional trace from
the gate of the IGBT to the Clamp pin of the gate driver is
introduced. After the VO output has gone below the Active
Miler Clamp threshold VMC−THR the Clamp pin is shorted
to GND and thus prevents the voltage on the gate of the
IGBT to rise above the threshold voltage as shown in
Figure 25. The Clamp pin is disconnected from GND as
soon as the signal to turn on the IGBT arrives to the gate
driver input. The fact that the Clamp pin is engaged only
after the gate voltage drops below the VMC−THR threshold
ensures that the function of this pin does not interfere with
the normal turn−off switching performance that is user
controllable by choice of RG.
This feature (offered by NCV5701A) is a cost savvy
alternative to a negative gate voltage. The main requirement
is to hold the gate of the turned−off (for example low−side)
IGBT below the threshold voltage during the turn−on of the
opposite−side (in this example high−side) IGBT in the half
bridge. The turn−on of the high−side IGBT causes high dv/dt
transition on the collector of the turned−off low−side IGBT.
This high dv/dt then induces current (Miller current) through
the CGC capacitance (Miller capacitance) to the gate
capacitance of the low−side IGBT as shown in Figure 24. If
the path from gate to GND has critical impedance (caused
by RG) the Miller current could rise the gate voltage above
the threshold level. As a consequence the low−side IGBT
could be turned on for a few tens or hundreds of
nanoseconds. This causes higher switching losses. One way
to avoid this situation is to use negative gate voltage, but this
requires second DC source for the negative gate voltage.
www.onsemi.com
15
NCV5701A, NCV5701B, NCV5701C
Figure 24. Current Path without Miller Clamp
Protection
Figure 25. Current Path with Miller Clamp Protection
Desaturation Protection (DESAT)
At the turned−on output state of the driver, the current
IDESAT−CHG from current source starts to flow to the
blanking capacitor CBLANK, connected to DESAT pin.
Appropriate value of this capacitor has to be selected to
ensure that the DESAT pin voltage does not rise above the
threshold level VDESAT−THR before the IGBT fully turns on.
The blanking time is given by following expression.
According to this expression, a 47 pF CBLANK will provide
a blanking time of (47p *6.5/0.25m =) 1.22 ms.
This feature monitors the collector−emitter voltage of the
IGBT in the turned−on state. When the IGBT is fully turned
on, it operates in a saturation region. Its collector−emitter
voltage (called saturation voltage) is usually low, well below
3 V for most modern IGBTs. It could indicate an overcurrent
or similar stress event on the IGBT if the collector−emitter
voltage rises above the saturation voltage, after the IGBT is
fully turned on. Therefore the DESAT protection circuit
compares the collector−emitter voltage with a voltage level
VDESAT−THR to check if the IGBT didn’t leave the saturation
region. It will activate FLT output and shut down driver
output (thus turn−off the IGBT), if the saturation voltage
rises above the VDESAT−THR. This protection works on
every turn−on phase of the IGBT switching period.
At the beginning of turning−on of the IGBT, the
collector−emitter voltage is much higher than the saturation
voltage level which is present after the IGBT is fully turned
on. It takes almost 1 ms between the start of the IGBT turn−on
and the moment when the collector−emitter voltage falls to
the saturation level. Therefore the comparison is delayed by
a configurable time period (blanking time) to prevent false
triggering of DESAT protection before the IGBT
collector−emitter voltage falls below the saturation level.
Blanking time is set by the value of the capacitor CBLANK.
The exact principle of operation of DESAT protection is
described with reference to Figure 26.
At the turned−off output state of the driver, the DESAT pin
is shorted to ground via the discharging transistor (QDIS).
Therefore, the inverting input holds the comparator output
at low level.
t BLANK + C BLANK @
V DESAT−THR
I DESAT−CHG
After the IGBT is fully turned−on, the IDESAT−CHG flows
through the DESAT pin to the series resistor RS−DESAT and
through the high voltage diode and then through the
collector and IGBT to the emitter. Care must be taken to
select the resistor RS−DESAT value so that the sum of the
saturation voltage, drop on the HV diode and drop on the
RS−DESAT caused by current IDESAT−CHG flowing from
DESAT source current is smaller than the DESAT threshold
voltage. Following expression can be used:
V DESAT−THR u
R S−DESAT @ I DESAT−CHG ) V F_HV diode ) V CESAT_IGBT
Important part for DESAT protection to work properly is
the high voltage diode. It must be rated for at least same
voltage as the low side IGBT. The safety margin is
application dependent.
The typical waveforms for IGBT overcurrent condition
are outlined in Figure 27.
www.onsemi.com
16
NCV5701A, NCV5701B, NCV5701C
Figure 26. Desaturation Protection Schematic
Figure 27. Desaturation Protection Waveforms
www.onsemi.com
17
NCV5701A, NCV5701B, NCV5701C
Input Signal
The input signal controls the gate driver output. Figure 28
shows the typical connection diagrams for isolated
applications where the input is coming through an
opto−coupler or a pulse transformer.
Figure 28. Opto−coupler or Pulse Transformer At Input
The relationship between gate driver input signal from a
pulse transformer (Figure 29) or opto−coupler (Figure 30)
and the output is defined by many time and voltage values.
The time values include output turn−on and turn−off delays
(tpd−on and tpd−off), output rise and fall times (trise and tfall)
and minimum input pulse−width (ton−min). Note that the
delay times are defined from 50% of input transition to first
10% of the output transition to eliminate the load
dependency. The input voltage parameters include input
high (VIN−H1) and low (VIN−L1) thresholds as well as the
input range for which no output change is initiated
(VIN−NC).
VIN−H1
VIN−NC
VIN
VIN−L1
tpd−off
tfall
tpd−on
trise
ton−min
VOUT
90%
10%
Figure 29. Input and Output Signal Parameters for Pulse Transformer
www.onsemi.com
18
NCV5701A, NCV5701B, NCV5701C
VIN−H1
VIN−NC
VIN
VIN−L1
tpd−off
tfall
ton−min
trise
tpd−on
VOUT
90%
10%
Figure 30. Input and Output Signal Parameters for Opto−coupler
Use of VREF Pin
The NCV5701 provides an additional 5.0 V output
(VREF) that can serve multiple functions. This output is
capable of sourcing up to 10 mA current for functions such
as opto−coupler interface or external comparator interface.
The VREF pin should be bypassed with at least a 100 nF
capacitor (higher the better) irrespective of whether it is
being utilized for external functionality or not. VREF is
highly stable over temperature and line/load variations (see
characteristics curves for details)
Fault Output Pin
This pin provides the feedback to the controller about the
driver operation. The situations in which the FLT signal
becomes active (low value) are summarized in the Table 6.
Table 6. FLT LOGIC TRUTH TABLE
VIN
UVLO
DESAT
Internal TSD
VOUT
FLT
Notes
L
Inactive
L
L
H
H
Normal operation − Output High
H
Inactive
L
L
L
H
Normal operation − Output Low
X
Active
X
L
L
L
UVLO activated − FLT Low (td3-FLT), Output Low
(td3-FLT + td1−OUT)
L
Inactive
H
L
L
L
DESAT activated (only when VIN is low) − Output Low
(td2_OUT), FLT Low
X
Inactive
X
H
L
L
Internal Thermal Shutdown − FLT Low (td3-FLT ), Output Low (td3-FLT + td1−OUT)
Thermal Shutdown
(12 ms), the output is pulled low and many of the internal
circuits are turned off. The 12 ms delay is meant to allow the
controller to perform an orderly shutdown sequence as
appropriate. Once the temperature goes below the second
threshold, the part becomes active again.
The NCV5701 also offers thermal shutdown function that
is primarily meant to self−protect the driver in the event that
the internal temperature gets excessive. Once the
temperature crosses the TSD threshold, the FLT output is
activated after a delay of td3-FLT. After a delay of td1−OUT
www.onsemi.com
19
NCV5701A, NCV5701B, NCV5701C
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AK
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
−X−
A
8
5
S
B
0.25 (0.010)
Y
M
M
1
4
K
−Y−
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
M
D
0.25 (0.010)
M
Z Y
S
X
J
S
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
◊
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
20
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCV5701/D