HMC695LP4 / 695LP4E v00.0808 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT FREQ. MULTIPLIERS - ACTIVE - SMT 7 Typical Applications Features The HMC695LP4(E) is ideal for: Output Power: +7 dBm • Fiber Optic Applications Sub-Harmonic Suppression: >25 dBc • Point-to-Point Radios SSB Phase Noise: -140 dBc/Hz • Military Radar Single Supply: +5V @ 60 mA 24 Lead 4x4 mm SMT Package: 16 mm2 Functional Diagram General Description The HMC695LP4(E) are active miniature x4 frequency multipliers utilizing InGaP GaAs HBT technology in 4x4 mm leadless surface mount packages. Power output is +7 dBm typical from a +5V supply voltage and varies little vs. input power, temperature and supply voltage. Suppression of undesired fundamental and sub-harmonics is >25 dBc typical with respect to output signal level. The low additive SSB phase noise of -140 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. The HMC695LP4(E) are ideal for use in LO multiplier chains allowing reduced parts count vs. traditional approaches. Electrical Specifi cations, TA = +25° C, Vcc= 5V Parameter Min. Frequency Range, Input Frequency Range, Output Max. -15 Output Power 2 Units GHz 11.4 - 13.2 Input Power Range GHz 5 dBm 7 dBm Sub-Harmonic Suppression 25 dBc Input Return Loss 15 dB Output Return Loss 8 dB SSB Phase Noise (100 kHz Offset) Supply Current (Icc) 7 - 118 Typ. 2.85 - 3.3 Pin= 0 dBm -140 60 dBc/Hz 75 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com mA HMC695LP4 / 695LP4E v00.0808 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT Output Power vs. Drive Level 10 8 8 6 +25 C +85 C -40 C 4 2 0 7 6 -20 dBm -15 dBm -10 dBm -5 dBm 0 dBm +5 dBm 4 2 0 11 11.5 12 12.5 13 13.5 14 11 11.5 OUTPUT FREQUENCY (GHz) Output Power vs. Supply Voltage @ -10 dBm Drive Level 13 13.5 14 0 -5 RETURN LOSS (dB) 8 6 Vcc=4.5V Vcc=5.0V Vcc=5.5V 4 2 +25 C +85 C -40 C -10 -15 -20 -25 0 -30 11 11.5 12 12.5 13 13.5 2 14 OUTPUT FREQUENCY (GHz) 2.5 3 Fout 1Fin 2Fin 3Fin OUTPUT POWER (dBm) 30 -5 -10 +25 C +85 C -40 C -20 8 10 12 FREQUENCY (GHz) 14 4 4.5 5 Harmonics @ -10 dBm Drive Level 0 -15 3.5 FREQUENCY (GHz) Output Return Loss vs. Temperature RETURN LOSS (dB) 12.5 Input Return Loss vs. Temperature 10 OUTPUT POWER (dBm) 12 OUTPUT FREQUENCY (GHz) FREQ. MULTIPLIERS - ACTIVE - SMT 10 OUTPUT POWER (dBm) OUTPUT POWER (dBm) Output Power vs. Temperature @ -10 dBm Drive Level 16 5Fin 6Fin 7Fin 8Fin 10 -10 -30 -50 -70 2.75 3 3.25 3.5 INPUT FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 119 HMC695LP4 / 695LP4E v00.0808 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT 7 - 120 SSB Phase Noise @ Pin = -10 dBm @ 12.5 GHz 0 0 -20 -20 SSB PHASE NOISE (dBc/Hz) FREQ. MULTIPLIERS - ACTIVE - SMT 7 SSB PHASE NOISE (dBc/Hz) SSB Phase Noise @ Pin = 0 dBm @ 12.5 GHz -40 -60 -80 -100 -120 -140 -160 2 10 3 4 10 10 5 10 6 10 7 10 -40 -60 -80 -100 -120 -140 -160 2 10 3 10 OFFSET FREQUENCY (Hz) Absolute Maximum Ratings 4 10 5 6 10 10 7 10 OFFSET FREQUENCY (Hz) Typical Supply Current vs. Vcc RF Input (Vcc= +5V) +20 dBm Vcc (V) Icc (mA) Vcc +5.5V 4.75 59 Channel Temperature 135 °C 5.00 60 Continuous Pdiss (T=85 °C) (derate 10.8 mW/°C above 85 °C) 538 mW 5.25 61 Thermal Resistance (Rth) (junction to ground paddle) 93 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C Note: Multiplier will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC695LP4 / 695LP4E v00.0808 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. FREQ. MULTIPLIERS - ACTIVE - SMT 7 Package Information Part Number Package Body Material Lead Finish MSL Rating HMC695LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC695LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H695 XXXX [2] H695 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 121 HMC695LP4 / 695LP4E v00.0808 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT Pin Description FREQ. MULTIPLIERS - ACTIVE - SMT 7 7 - 122 Pin Number Function Description 1, 2, 5 - 14, 17, 18, 20 - 24 N/C No Connection 3 RFIN RF input needs to be DC blocked only if there is an external DC voltage applied to RFIN. 4, 15 GND All ground leads and ground paddle must be soldered to PCB RF/DC ground. 16 RFOUT Multiplied Output. AC coupled. No external DC blocks necessary. 19 Vcc Supply voltage 5V Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC695LP4 / 695LP4E v00.0808 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT Evaluation PCB FREQ. MULTIPLIERS - ACTIVE - SMT 7 List of Materials for Evaluation PCB 106137 [1] Item Description J1 - J3 PCB Mount SMA Connector C1 1,000 pF Capacitor, 0603 Pkg. U1 HMC695LP4(E) x4 Active Multiplier PCB [2] 104610 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 4350 The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 123