Control Integrated POwer System (CIPOS™) IGCM06F60HA Datasheet Datasheet www.infineon.com Please read the Important Notice and Warnings at the end of this document <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA Table of Contents CIPOS™ Control Integrated POwer System ............................................................................................................ 3 Features .................................................................................................................................................................. 3 Target Applications ...................................................................................................................................................... 3 Description .................................................................................................................................................................. 3 System Configuration .................................................................................................................................................. 3 Pin Configuration ................................................................................................................................................... 4 Internal Electrical Schematic ................................................................................................................................. 4 Pin Assignment ...................................................................................................................................................... 5 Pin Description ...................................................................................................................................................... 5 HIN(U, V, W) and LIN(U, V, W) (Low side and high side control pins, Pin 7 - 12)......................................................... 5 VFO (Fault-output, Pin 14) ........................................................................................................................................... 6 ITRIP (Over current detection function, Pin 15).......................................................................................................... 6 VDD, VSS (Low side control supply and reference, Pin 13, 16) ................................................................................... 6 VB(U, V, W) and VS(U, V, W) (High side supplies, Pin 1 - 6) .......................................................................................... 6 NW, NV, NU (Low side emitter, Pin 17 - 19) ................................................................................................................. 6 W, V, U (High side emitter and low side collector, Pin 20 - 22) ................................................................................... 6 P (Positive bus input voltage, Pin 23) .......................................................................................................................... 6 Absolute Maximum Ratings ................................................................................................................................... 7 Module Section ............................................................................................................................................................ 7 Inverter Section............................................................................................................................................................ 7 Control Section ............................................................................................................................................................ 7 Recommended Operation Conditions ................................................................................................................... 8 Static Parameters .................................................................................................................................................. 9 Dynamic Parameters ........................................................................................................................................... 10 Bootstrap Parameters ......................................................................................................................................... 10 Mechanical Characteristics and Ratings .............................................................................................................. 11 Switching Times Definition .................................................................................................................................. 11 Circuit of a Typical Application ............................................................................................................................ 12 Electrical characteristic ....................................................................................................................................... 13 Package Outline ................................................................................................................................................... 14 Revision History ................................................................................................................................................... 15 Datasheet 2 <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA CIPOS™ Control Integrated POwer System Dual In-Line Intelligent Power Module 3Φ -bridge 600V / 6A Features Description Fully isolated Dual In-Line molded module The CIPOS™ module family offers the chance for integrating various power and control components to increase reliability, optimize PCB size and system costs. Reverse conducting IGBTs with monolithic body diode Rugged SOI gate driver technology with stability against transient and negative voltage Allowable negative VS potential up to -11V for signal transmission at VBS=15V Integrated bootstrap functionality Over current shutdown Under-voltage lockout at all channels Low side emitter pins accessible for all phase current monitoring (open emitter) Cross-conduction prevention All of 6 switches turn off during protection Lead-free terminal plating; RoHS compliant It is designed to control three phase AC motors and permanent magnet motors in variable speed drives for applications like a refrigerator and a dish washer. The package concept is specially adapted to power applications, which need good thermal conduction and electrical isolation, but also EMI-save control and overload protection. The reverse conducting IGBTs are combined with an optimized SOI gate driver for excellent electrical performance. System Configuration Target Applications 3 half bridges with reverse conducting IGBTs Dish washers 3Φ SOI gate driver Refrigerators Pin-to-heatsink clearance distance typ. 1.6mm Fans Low power motor drives Datasheet 3 <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA Pin Configuration Bottom View (24) NC (1) VS(U) (2) VB(U) (23) P (3) VS(V) (4) VB(V) (22) U (5) VS(W) (6) VB(W) (21) V (7) HIN(U) (8) HIN(V) (9) HIN(W) (10) LIN(U) (11) LIN(V) (12) LIN(W) (13) VDD (14) VFO (20) W (19) NU (18) NV (15) ITRIP (16) VSS (17) NW Figure 1 Pin configuration Internal Electrical Schematic NC (24) P (23) (1) VS(U) (2) VB(U) VB1 HO1 RBS1 VS1 U (22) (3) VS(V) (4) VB(V) VB2 RBS2 HO2 VS2 V (21) (5) VS(W) (6) VB(W) VB3 RBS3 Figure 2 Datasheet (7) HIN(U) HIN1 (8) HIN(V) HIN2 (9) HIN(W) (10) LIN(U) HIN3 LIN1 (11) LIN(V) LIN2 (12) LIN(W) LIN3 (13) VDD VDD (14) VFO VFO (15) ITRIP ITRIP (16) VSS VSS HO3 VS3 W (20) LO1 NU (19) LO2 NV (18) LO3 NW (17) Internal schematic 4 <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA Pin Assignment Pin Number Pin Name Pin Description 1 VS(U) U-phase high side floating IC supply offset voltage 2 VB(U) U-phase high side floating IC supply voltage 3 VS(V) V-phase high side floating IC supply offset voltage 4 VB(V) V-phase high side floating IC supply voltage 5 VS(W) W-phase high side floating IC supply offset voltage 6 VB(W) W-phase high side floating IC supply voltage 7 HIN(U) U-phase high side gate driver input 8 HIN(V) V-phase high side gate driver input 9 HIN(W) W-phase high side gate driver input 10 LIN(U) U-phase low side gate driver input 11 LIN(V) V-phase low side gate driver input 12 LIN(W) W-phase low side gate driver input 13 VDD Low side control supply 14 VFO Fault output 15 ITRIP Over current shutdown input 16 VSS Low side control negative supply 17 NW W-phase low side emitter 18 NV V-phase low side emitter 19 NU U-phase low side emitter 20 W Motor W-phase output 21 V Motor V-phase output 22 U Motor U-phase output 23 P Positive bus input voltage 24 NC No Connection Pin Description HIN(U, V, W) and LIN(U, V, W) (Low side and high side control pins, Pin 7 - 12) These pins are positive logic and they are responsible for the control of the integrated IGBT. The Schmitt-trigger input thresholds of them are such to guarantee LSTTL and CMOS compatibility down to 3.3V controller outputs. Pull-down resistor of about 5k is internally provided to pre-bias inputs during supply start-up and a zener clamp is provided for pin protection purposes. Input Schmitt-trigger and noise filter provide beneficial noise rejection to short input pulses. CIPOSTM Schmitt-Trigger HINx LINx Figure 3 a) INPUT NOISE FILTER UZ=10.5V SWITCH LEVEL VIH; VIL VSS Input pin structure tFILIN b) tFILIN HIN LIN HIN LIN high The noise filter suppresses control pulses which are below the filter time tFILIN. The filter acts according to Figure 4. Datasheet 5k HO LO Figure 4 5 low HO LO Input filter timing diagram <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA It is not recommended for proper work to provide input pulse-width lower than 1µs. The under-voltage circuit enables the device to operate at power on when a supply voltage of at least a typical voltage of VDDUV+ = 12.1V is present. The integrated gate drive provides additionally a shoot through prevention capability which avoids the simultaneous on-state of two gate drivers of the same leg (i.e. HO1 and LO1, HO2 and LO2, HO3 and LO3). When two inputs of a same leg are activated, only former activated one is activated so that the leg is kept steadily in a safe state. The IC shuts down all the gate drivers power outputs, when the VDD supply voltage is below VDDUV- = 10.4V. This prevents the external power switches from critically low gate voltage levels during on-state and therefore from excessive power dissipation. A minimum deadtime insertion of typically 380ns is also provided by driver IC, in order to reduce crossconduction of the external power switches. VB(U, V, W) and VS(U, V, W) (High side supplies, Pin 1 - 6) VB to VS is the high side supply voltage. The high side circuit can float with respect to VSS following the external high side power device emitter voltage. VFO (Fault-output, Pin 14) The VFO pin indicates a module failure in case of under voltage at pin VDD or in case of triggered over current detection at ITRIP. A pull-up resistor is externally required. Due to the low power consumption, the floating driver stage is supplied by integrated bootstrap circuit. The under-voltage detection operates with a rising supply threshold of typical VBSUV+ = 12.1V and a falling threshold of VBSUV- = 10.4V. CIPOSTM VDD RON,FLT From ITRIP - Latch VFO 1 VSS Figure 5 VS(U, V, W) provide a high robustness against negative voltage in respect of VSS of -50V transiently. This ensures very stable designs even under rough conditions. From UV detection Internal circuit at pin VFO NW, NV, NU (Low side emitter, Pin 17 - 19) ITRIP (Over current detection function, Pin 15) The low side emitters are available for current measurements of each phase leg. It is recommended to keep the connection to pin VSS as short as possible in order to avoid unnecessary inductive voltage drops. CIPOS™ provides an over current detection function by connecting the ITRIP input with the IGBT collector current feedback. The ITRIP comparator threshold (typ. 0.47V) is referenced to VSS ground. An input noise filter (typ.: tITRIPMIN = 530ns) prevents the driver to detect false overcurrent events. W, V, U (High side emitter and low side collector, Pin 20 - 22) These pins are motor U, V, W input pins. Over current detection generates a shutdown of all outputs of the gate driver after the shutdown propagation delay of typically 1000ns. P (Positive bus input voltage, Pin 23) The high side IGBTs are connected to the bus voltage. It is noted that the bus voltage does not exceed 450V. The fault-clear time is set to minimum 40µs. VDD, VSS (Low side control supply and reference, Pin 13, 16) VDD is the control supply and it provides power both to input logic and to output power stage. Input logic is referenced to VSS ground. Datasheet 6 <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA Absolute Maximum Ratings (VDD = 15V and TJ = 25°C, if not stated otherwise) Module Section Description Condition Storage temperature range Isolation test voltage RMS, f = 60Hz, t = 1min Operating case temperature range Refer to Figure 6 Symbol Value Unit min max Tstg -40 125 °C VISOL 2000 - V TC -40 100 °C Inverter Section Description Condition Symbol Value min max Unit Max. blocking voltage IC = 250µA VCES 600 - V DC link supply voltage of P-N Applied between P-N VPN - 450 V DC link supply voltage (surge) of P-N Applied between P-N VPN(surge) - 500 V Output current TC = 25°C, TJ < 150°C TC = 100°C, TJ < 150°C IC -6 -4 6 4 A Maximum peak output current less than 1ms IC(peak) -12 12 A Short circuit withstand time1 VDC ≤ 400V, TJ = 150°C tSC - 5 µs Power dissipation per IGBT Ptot - 23.6 W Operating junction temperature range TJ -40 150 °C RthJC - 5.3 K/W Single IGBT thermal resistance, junction-case Control Section Description Condition Value min max Unit Module supply voltage VDD -1 20 V High side floating supply voltage (VB vs. VS) VBS -1 20 V VIN VITRIP -1 -1 10 10 V fPWM - 20 kHz Input voltage LIN, HIN, ITRIP Switching frequency 1 Symbol Allowed number of short circuits: <1000; time between short circuits: >1s. Datasheet 7 <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA Recommended Operation Conditions All voltages are absolute voltages referenced to VSS -potential unless otherwise specified. Description Symbol Value min typ max Unit DC link supply voltage of P-N VPN 0 - 400 V High side floating supply voltage (VB vs. VS) VBS 13.5 - 18.5 V Low side supply voltage VDD 14.0 16 18.5 V Control supply variation ΔVBS, ΔVDD -1 -1 - 1 1 V/µs Logic input voltages LIN, HIN, ITRIP VIN VITRIP 0 0 - 5 5 V Between VSS - N (including surge) VSS -5 - 5 V Figure 6 TC measurement point1 Any measurement except for the specified point in figure 6 is not relevant for the temperature verification and brings wrong or different information. 1 Datasheet 8 <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA Static Parameters (VDD = 15V and TJ = 25°C, if not stated otherwise) Description Condition min Value typ max VCE(sat) - 1.6 1.8 2.0 - V Symbol Unit IC = 4A Collector-Emitter saturation voltage TJ = 25°C 150°C IF = 4A Emitter-Collector forward voltage TJ = 25°C 150°C VF - 1.75 1.8 2.2 - V Collector-Emitter leakage current VCE = 600V ICES - - 1 mA Logic "1" input voltage (LIN, HIN) VIH - 2.1 2.5 V Logic "0" input voltage (LIN, HIN) VIL 0.7 0.9 - V ITRIP positive going threshold VIT,TH+ 400 470 540 mV ITRIP input hysteresis VIT,HYS 40 70 - mV VDD and VBS supply under voltage positive going threshold VDDUV+ VBSUV+ 10.8 12.1 13.0 V VDD and VBS supply under voltage negative going threshold VDDUVVBSUV- 9.5 10.4 11.2 V VDD and VBS supply under voltage lockout hysteresis VDDUVH VBSUVH 1.0 1.7 - V Input clamp voltage (HIN, LIN, ITRIP) Iin=4mA VINCLAMP 9.0 10.1 12.5 V Quiescent VBx supply current (VBx only) HIN = 0V IQBS - 300 500 µA Quiescent VDD supply current (VDD only) LIN = 0V, HINX = 5V IQDD - 370 900 µA Input bias current VIN = 5V IIN+ - 1 1.5 mA Input bias current VIN = 0V IIN- - 2 - µA ITRIP input bias current VITRIP = 5V IITRIP+ - 65 150 µA VFO input bias current VFO = 5V, VITRIP = 0V IFO - 2 - nA VFO output voltage IFO = 10mA, VITRIP = 1V VFO - 0.5 - V Datasheet 9 <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA Dynamic Parameters (VDD = 15V and TJ = 25°C, if not stated otherwise) Description tITRIPmin min - Value typ 650 20 100 130 680 180 220 1420 530 max - VLIN, HIN = 0V & 5V tFILIN - 290 - ns VITRIP = 1V tFLTCLR 40 65 200 µs DTPWM 1.0 - - µs DTIC - 380 - ns Eon - 75 130 - µJ Eoff - 120 190 - µJ Erec - 40 70 - µJ min 600 Value typ - max - Condition Turn-on propagation delay time Turn-on rise time Turn-on switching time Reverse recovery time Turn-off propagation delay time Turn-off fall time Turn-off switching time Short circuit propagation delay time Input filter time ITRIP Input filter time at LIN, HIN for turn on and off Fault clear time after ITRIP-fault Deadtime between low side and high side Deadtime of gate drive circuit IGBT turn-on energy (includes reverse recovery of diode) IGBT turn-off energy Diode recovery energy VLIN, HIN = 5V, IC = 4A, VDC = 300V VLIN, HIN = 0V, IC = 4A, VDC = 300V From VIT,TH+ to 10% ISC VITRIP = 1V VDC = 300V, IC = 4A TJ = 25°C 150°C VDC = 300V, IC = 4A TJ = 25°C 150°C VDC = 300V, IC = 4A TJ = 25°C 150°C Symbol ton tr tc(on) trr toff tf tc(off) tSCP Unit ns ns ns ns ns ns ns ns ns Bootstrap Parameters (TJ = 25°C, if not stated otherwise) Description Condition Repetitive peak reverse voltage Bootstrap diode resistance of U-phase1 Reverse recovery time Forward voltage drop 1 Symbol VRRM VS2 or VS3 = 300V, TJ = 25°C VS2 and VS3 = 0V, TJ = 25°C VS2 or VS3 = 300V, TJ = 125°C VS2 and VS3 = 0V, TJ = 125°C IF = 0.6A, di/dt = 80A/µs IF = 20mA, VS2 and VS3 = 0V RBS1 - 35 40 50 65 trr_BS VF_BS - 50 2.6 Unit V - Ω - ns V RBS2 and RBS3 have same values to RBS1. Datasheet 10 <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA Mechanical Characteristics and Ratings Description Condition Mounting torque Flatness Weight M3 screw and washer Refer to Figure 7 Value typ 0.69 6.15 min 0.59 -50 - max 0.78 100 - Unit Nm µm g + - - + Figure 7 Flatness measurement position Switching Times Definition HINx LINx 2.1V 0.9V trr toff ton 10% iCx 90% 90% tf 10% tr 10% 10% 10% vCEx tc(on) tc(off) Figure 8 Datasheet Switching times definition 11 <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA Circuit of a Typical Application NC (24) P (23) (1) VS(U) (2) VB(U) HO1 VB1 RBS1 VS1 U (22) (3) VS(V) #4 (4) VB(V) VB2 RBS2 HO2 VS2 V (21) 3-ph AC Motor (5) VS(W) (6) VB(W) VB3 RBS3 HO3 VS3 W (20) #5 #1 (7) HIN(U) (8) HIN(V) (9) HIN(W) (10) LIN(U) (11) LIN(V) Micro Controller HIN1 LO1 HIN2 NU (19) HIN3 LIN1 LIN2 LO2 (12) LIN(W) #7 #6 LIN3 NV (18) (13) VDD VDD line (14) VFO (15) ITRIP (16) VSS VFO ITRIP LO3 NW (17) VSS Control GND line 5 or 3.3V line Power GND line VDD #3 #2 <Signal for protection> Figure 9 1. - Capacitor for high side floating supply voltage should be placed as close to VB and VS pins as possible. The wiring between CIPOS™ Mini and snubber capacitor including shunt resistor should be as short as possible. Shunt resistor - 7. VFO output is an open drain output. This signal line should be pulled up to the positive side of the 5V/3.3V logic power supply with a proper resistor RPU. It is recommended that RC filter be placed as close to the controller as possible. Snubber capacitor - 6. To prevent protection function errors, CITRIP should be placed as close to Itrip and VSS pins as possible. VB-VS circuit - 5. To reduce input signal noise by high speed switching, the RIN and CIN filter circuit should be mounted. (100Ω, 1nF) CIN should be placed as close to VSS pin as possible. VFO circuit - 4. Typical application circuit Itrip circuit - 3. <Signal for protection> Input circuit - 2. U-phase current sensing V-phase current sensing W-phase current sensing The shunt resistor of SMD type should be used for reducing its stray inductance. Ground pattern - Ground pattern should be separated at only one point of shunt resistor as short as possible. Datasheet 12 <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA Electrical characteristic 12 12 Ic, Collector - Emitter current [A] 9 8 7 6 5 VDD=13V VDD=15V VDD=20V 4 3 2 1 0.5 1.0 1.5 2.0 2.5 3.0 3.5 9 8 7 6 5 4 TJ=25℃ 3 TJ=150℃ 2 1 0 0.0 4.0 Typ. Collector – Emitter saturation voltage 1.0 2.0 2.5 3.0 3.5 4.0 9 8 7 6 5 4 High side @TJ=25℃ High side @TJ=150℃ 0.6 Low side @TJ=25℃ Low side @TJ=150℃ 0.5 0.4 0.3 0.2 0.1 1 0 0.0 4.5 1 2 3 4 5 6 7 8 9 10 11 High side @TJ=150℃ Low side @TJ=25℃ Low side @TJ=150℃ 0.25 0.20 0.15 0.10 0.05 VDC=300V VDD=15V 1 2 3 4 5 6 7 8 9 10 11 High side @TJ=150℃ Low side @TJ=25℃ Low side @TJ=150℃ 750 700 650 600 2 3 4 5 6 7 8 High side @TJ=25℃ High side @TJ=150℃ 300 Low side @TJ=25℃ Low side @TJ=150℃ 250 200 150 100 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 trr, Reverse recovery time [ns] 900 800 High side @TJ=25℃ High side @TJ=150℃ 600 Low side @TJ=25℃ 500 Low side @TJ=150℃ 400 300 200 100 0 4 5 6 7 8 9 Ic, Collector current [A] Typ. Turn off switching time Datasheet 10 11 12 3 4 5 6 7 8 9 10 11 12 High side @TJ=25℃ High side @TJ=150℃ 1400 Low side @TJ=25℃ Low side @TJ=150℃ 1200 1000 800 0 450 VDC=300V VDD=15V 400 High side @TJ=25℃ Low side @TJ=25℃ Low side @TJ=150℃ 300 2 3 4 5 6 7 8 9 10 11 12 Typ. Turn off propagation delay time High side @TJ=150℃ 350 1 Ic, Collector current [A] 250 10 1 D : duty ratio 0.1 D=50% D=20% D=10% D=5% D=2% Single pulse 0.01 200 150 1E-3 100 50 3 2 VDC=300V VDD=15V 12 500 2 1 1600 Typ. Turn on switching time VDC=300V VDD=15V 1 20 Ic, Collector current [A] 1100 0 40 600 0 Typ. Turn on propagation delay time 700 60 1800 VDC=300V VDD=15V 350 Ic, Collector current [A] 1000 80 Typ. Reverse recovery energy loss 0 1 Low side @TJ=150℃ 100 Ic, Collector current [A] 50 0 Low side @TJ=25℃ 120 0 toff, Turn off propagation delay time [ns] tc(on), Turn on switching time [ns] High side @TJ=25℃ 3.5 High side @TJ=150℃ 140 12 400 850 3.0 High side @TJ=25℃ 160 Typ. Turn off switching energy loss VDC=300V VDD=15V 2.5 VDC=300V VDD=15V 180 Ic, Collector current [A] 900 2.0 0 0 Typ. Turn on switching energy loss 1.5 200 0.30 12 1.0 Typ. Emitter – Collector forward voltage High side @TJ=25℃ 0.35 Ic, Collector current [A] 800 0.5 VF, Emitter - Collector voltage [V] 0.00 0 TJ=150℃ 2 Erec, Reverse recovery energy loss [uJ] Eoff, Turn off switching energy loss [mJ] 0.8 0.7 TJ=25℃ 3 0.40 VDC=300V VDD=15V 0.9 0.0 ton, Turn on propagation delay time [ns] 1.5 Typ. Collector – Emitter saturation voltage 1.0 Eon, Turn on switching energy loss [mJ] 0.5 10 VCE(sat), Collector - Emitter voltage [V] VCE(sat), Collector - Emitter voltage [V] tc(off), Turn off switching time [ns] 11 10 ZthJC, RC-IGBT transient thermal resistance [K/W] Ic, Collector - Emitter current [A] 10 0 0.0 12 VDD=15V 11 IF, Emitter - Collector current [A] TJ=25℃ 11 0 0 1 2 3 4 5 6 7 8 9 Ic, Collector current [A] Typ. Reverse recovery time 13 10 11 12 1E-4 1E-7 1E-6 1E-5 1E-4 1E-3 0.01 0.1 1 10 tP, Pulse width [sec.] IGBT transient thermal resistance at all six IGBTs operation <Revision 2.7> <2016-08-01> 100 Control Integrated POwer System (CIPOS™) IGCM06F60HA Package Outline Datasheet 14 <Revision 2.7> <2016-08-01> Control Integrated POwer System (CIPOS™) IGCM06F60HA Revision History Major changes since the last revision Page or Reference Description of change Additional information and typo corrections 4 Pin configuration 14 Package outline Datasheet 15 <Revision 2.7> <2016-08-01> Trademarks of Infineon Technologies AG µHVIC™, µIPM™, µPFC™, AU-ConvertIR™, AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolDP™, CoolGaN™, COOLiR™, CoolMOS™, CoolSET™, CoolSiC™, DAVE™, DI-POL™, DirectFET™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, GaNpowIR™, HEXFET™, HITFET™, HybridPACK™, iMOTION™, IRAM™, ISOFACE™, IsoPACK™, LEDrivIR™, LITIX™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OPTIGA™, OptiMOS™, ORIGA™, PowIRaudio™, PowIRStage™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, SmartLEWIS™, SOLID FLASH™, SPOC™, StrongIRFET™, SupIRBuck™, TEMPFET™, TRENCHSTOP™, TriCore™, UHVIC™, XHP™, XMC™ Trademarks updated November 2015 Other Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition <2016-08-01> Published by Infineon Technologies AG 81726 München, Germany ifx1owners. © 2016 Infineon Technologies AG. All Rights Reserved. Do you have a question about this document? Email: [email protected] Document reference ifx1 IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”). With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer’s compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer’s products and any use of the product of Infineon Technologies in customer’s applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on the product, technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies office (www.infineon.com). Please note that this product is not qualified according to the AEC Q100 or AEC Q101 documents of the Automotive Electronics Council. WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.