Ten Degrees of Freedom Inertial Sensor ADIS16407 FEATURES GENERAL DESCRIPTION Triaxial digital gyroscope with digital range scaling ±75°/sec, ±150°/sec, ±300°/sec settings Axis-to-axis alignment, <0.05° Triaxial digital accelerometer, ±18 g minimum Triaxial digital magnetometer, ±2.5 gauss minimum Digital barometer, 10 mbar to 1200 mbar Calibrated pressure range: 300 mbar to 1100 mbar Autonomous operation and data collection No external configuration commands required 210 ms start-up time, 4 ms sleep mode recovery time Factory calibrated sensitivity, bias, and axial alignment Calibration temperature range: −40°C to +85°C SPI-compatible serial interface Embedded temperature sensor Programmable operation and control Automatic and manual bias correction controls Bartlett window FIR length, number of taps Digital I/O: data ready, alarm indicator, general-purpose Alarms for condition monitoring Sleep mode for power management DAC output voltage Enable external sample clock input up to 1.1 kHz Single command self test Single-supply operation: 4.75 V to 5.25 V 2000 g shock survivability Operating temperature range: −40°C to +105°C The ADIS16407 iSensor® device is a complete inertial system that includes a triaxial gyroscope, a triaxial accelerometer, a triaxial magnetometer, and pressure sensors. Each sensor in the ADIS16407 combines industry-leading iMEMS® technology with signal conditioning that optimizes dynamic performance. The factory calibration characterizes each sensor for sensitivity, bias, alignment, and linear acceleration (gyro bias). As a result, each sensor has its own dynamic compensation formulas that provide accurate sensor measurements. The ADIS16407 provides a simple, cost-effective method for integrating accurate, multiaxis inertial sensing into industrial systems, especially when compared with the complexity and investment associated with discrete designs. All necessary motion testing and calibration are part of the production process at the factory, greatly reducing system integration time. Tight orthogonal alignment simplifies inertial frame alignment in navigation systems. The SPI and register structure provide a simple interface for data collection and configuration control. The ADIS16407 has a compatible pinout for systems that currently use ADIS1635x, ADIS1636x, and ADIS1640x IMU products. The ADIS16407 is packaged in a module that is approximately 23 mm × 23 mm × 23 mm and has a standard connector interface. APPLICATIONS Platform stabilization and control Navigation Robotics FUNCTIONAL BLOCK DIAGRAM DIO1 DIO2 DIO3 DIO4 RST SELF TEST I/O VDD ALARMS POWER MANAGEMENT GND TRIAXIAL GYRO CONTROLLLER TRIAXIAL MAGN CALIBRATION AND FILTERS PRESSURE TEMP CLOCK VDD ADIS16407 OUTPUT DATA REGISTERS CS SCLK SPI USER CONTROL REGISTERS DIN DOUT 09797-001 TRIAXIAL ACCEL Figure 1. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2011 Analog Devices, Inc. All rights reserved. ADIS16407 TABLE OF CONTENTS Features .............................................................................................. 1 Data Ready Input/Output Indicator ........................................ 17 Applications....................................................................................... 1 General-Purpose Input/Output................................................ 17 General Description ......................................................................... 1 Auxiliary DAC ............................................................................ 17 Functional Block Diagram .............................................................. 1 Digital Processing Configuration................................................. 18 Revision History ............................................................................... 2 Sample Rate................................................................................. 18 Specifications..................................................................................... 3 Input Clock Configuration ....................................................... 18 Timing Specifications .................................................................. 6 Digital Filtering........................................................................... 18 Absolute Maximum Ratings............................................................ 7 Dynamic Range .......................................................................... 18 ESD Caution.................................................................................. 7 Calibration....................................................................................... 19 Pin Configuration and Function Descriptions............................. 8 Gyroscopes .................................................................................. 19 Typical Performance Characteristics ............................................. 9 Accelerometers ........................................................................... 20 Basic Operation............................................................................... 10 Magnetometer Calibration........................................................ 20 Reading Sensor Data.................................................................. 10 Flash Updates.............................................................................. 21 Output Data Registers................................................................ 11 Restoring Factory Calibration .................................................. 21 Input ADC Channel................................................................... 13 Alarms.............................................................................................. 22 Device Configuration ................................................................ 13 Static Alarm Use ......................................................................... 22 User Registers.................................................................................. 14 Dynamic Alarm Use .................................................................. 22 System Functions............................................................................ 15 Alarm Reporting ........................................................................ 22 Global Commands ..................................................................... 15 Applications Information .............................................................. 23 Power Management.................................................................... 15 Installation/Handling................................................................. 23 Product Identification................................................................ 15 Gyroscope Bias Optimization................................................... 23 Memory Management ............................................................... 15 Interface Printed Circuit Board (PCB).................................... 23 Self Test Function ....................................................................... 16 Outline Dimensions ....................................................................... 24 Status/Error Flags ....................................................................... 16 Ordering Guide .......................................................................... 24 Input/Output Configuration......................................................... 17 REVISION HISTORY 6/11—Rev. 0 to Rev. A Changes to Device Configuration Section and Figure 16......... 13 Changes to Figure 19...................................................................... 18 Changes to Figure 25 Caption....................................................... 24 Changes to Ordering Guide .......................................................... 24 4/11—Revision 0: Initial Version Rev. A | Page 2 of 24 ADIS16407 SPECIFICATIONS TA = 25°C, VDD = 5 V, angular rate = 0°/sec, dynamic range = ±300°/sec ± 1 g, unless otherwise noted. Table 1. Parameter GYROSCOPES Dynamic Range Initial Sensitivity Sensitivity Temperature Coefficient Misalignment Nonlinearity Initial Bias Error In-Run Bias Stability Angular Random Walk Bias Temperature Coefficient Linear Acceleration Effect on Bias Bias Voltage Sensitivity Output Noise Rate Noise Density 3 dB Bandwidth Sensor Resonant Frequency ACCELEROMETERS Dynamic Range Initial Sensitivity Sensitivity Temperature Coefficient Misalignment Nonlinearity Initial Bias Error In-Run Bias Stability Velocity Random Walk Bias Temperature Coefficient Bias Voltage Sensitivity Output Noise Noise Density 3 dB Bandwidth Sensor Resonant Frequency MAGNETOMETER Dynamic Range Initial Sensitivity Sensitivity Temperature Coefficient Misalignment Nonlinearity Initial Bias Error Bias Temperature Coefficient Output Noise Noise Density Bandwidth Test Conditions/Comments Dynamic range = ±300°/sec Dynamic range = ±150°/sec Dynamic range = ±75°/sec −40°C ≤ TA ≤ +85°C Axis to axis Axis to frame (package) Best fit straight line ±1 σ 1 σ, SMPL_PRD = 0x0001 1 σ, SMPL_PRD = 0x0001 −40°C ≤ TA ≤ +85°C Any axis, 1 σ (MSC_CTRL[7] = 1) VDD = 4.75 V to 5.25 V ±300°/sec range, no filtering f = 25 Hz, ±300°/sec range, no filtering Min Typ ±300 0.0495 ±350 0.05 0.025 0.0125 ±40 ±0.05 ±0.5 ±0.1 ±3 0.007 1.9 ±0.01 0.05 ±0.3 0.8 0.044 330 14.5 Max 0.0505 Unit °/sec °/sec/LSB °/sec/LSB °/sec/LSB ppm/°C Degrees Degrees % of FS °/sec °/sec °/√hr °/sec/°C °/sec/g °/sec/V °/sec rms °/sec/√Hz rms Hz kHz Each axis ±18 3.285 −40°C ≤ TA ≤ +85°C Axis to axis Axis to frame (package) Best fit straight line ±1 σ 1 σ, SMPL_PRD = 0x0001 1 σ, SMPL_PRD = 0x0001 −40°C ≤ TA ≤ +85°C VDD = 4.75 V to 5.25 V No filtering No filtering ±2.5 0.49 25°C 25°C, 1 σ Axis to axis Axis to frame (package) Best fit straight line 25°C, 0 gauss stimulus −40°C ≤ TA ≤ +85°C 25°C, no filtering, rms 25°C, no filtering, rms −3 dB Rev. A | Page 3 of 24 3.33 ±50 0.2 ±0.5 0.1 ±50 0.2 0.2 ±0.3 2.5 9 0.5 330 5.5 ±3.5 0.5 600 0.25 0.5 0.5 ±4 0.5 1.15 0.06 1540 3.38 0.51 g mg/LSB ppm/°C Degrees Degrees % of FS mg mg m/sec/√hr mg/°C mg/V mg rms mg/√Hz rms Hz kHz gauss mgauss/LSB ppm/°C Degrees Degrees % of FS mgauss mgauss/°C mgauss mgauss/√Hz Hz ADIS16407 Parameter BAROMETER Pressure Range Operating Extended 1 Sensitivity Total Error Relative Error 3 Linearity 4 Test Conditions/Comments Min 300 10 ADC INPUT Resolution Integral Nonlinearity Differential Nonlinearity Offset Error Gain Error Input Range Input Capacitance DAC OUTPUT Resolution Relative Accuracy Differential Nonlinearity Offset Error Gain Error Output Range Output Impedance Output Settling Time LOGIC INPUTS 5 Input High Voltage, VIH Input Low Voltage, VIL Unit 1100 1200 BARO_OUT only 2 25°C, 300 mbar to 1100 mbar −40°C to +85°C, 300 mbar to 1100 mbar 25°C, 300 mbar to 1100 mbar −40°C to +85°C, 300 mbar to 1100 mbar 0.08 1.5 2.5 0.1 0.15 0.027 25°C, output = 0x0000 0.14 °C/LSB 12 ±2 ±1 ±4 ±2 Bits LSB LSB LSB LSB V pF 0 During acquisition 5 kΩ/100 pF to GND 3.3 20 12 ±4 ±1 ±5 ±0.5 101 LSB ≤ input code ≤ 4095 LSB 0 3.3 2 10 2.0 0.8 0.55 CS signal to wake up from sleep mode CS Wake-Up Pulse Width Logic 1 Input Current, IIH Logic 0 Input Current, IIL All Pins Except RST RST Pin Input Capacitance, CIN DIGITAL OUTPUTS5 Output High Voltage, VOH Output Low Voltage, VOL FLASH MEMORY Data Retention 7 FUNCTIONAL TIMES 8 Power-On Start-Up Time Reset Recovery Time Sleep Mode Recovery Time Flash Memory Update Time Flash Memory Test Time Automatic Self Test Time Max mbar mbar mbar/LSB mbar mbar % of FS % of FS mbar rms Noise TEMPERATURE SENSOR Scale Factor Typ 20 VIH = 3.3 V VIL = 0 V ISOURCE = 1.6 mA ISINK = 1.6 mA Endurance 6 TJ = 85°C Time until new data is available SMPL_PRD = 0x0001 Rev. A | Page 4 of 24 ±0.2 ±10 40 1 10 60 2.4 0.4 10,000 20 210 90 7 75 30 52 Bits LSB LSB mV % V Ω μs V V V μs μA μA mA pF V V Cycles Years ms ms ms ms ms ms ADIS16407 Parameter CONVERSION RATE xGYRO_OUT, xACCL_OUT, xMAGN_OUT BAR_OUT, BARO_OUTL 9 Clock Accuracy Sync Input Clock 10 POWER SUPPLY Power Supply Current Test Conditions/Comments Min SMPL_PRD = 0x0001 SMPL_PRD = 0x0001 Operating voltage range, VDD Sleep mode 1 Typ Max 819.2 51.2 0.8 4.75 5.0 70 1.4 ±3 1.1 5.25 Unit SPS SPS SPS % kHz V mA mA The extended pressure range is guaranteed by design. See Table 22 for the BAR_OUTL register details, which offer additional digital resolution improvements. 3 The relative error assumes that the initial error, at +25°C, is corrected in the end application. 4 Linearity errors assume a full scale (FS) of 1000 mbar. 5 The digital I/O signals are driven by an internal 3.3 V supply, and the inputs are 5 V tolerant. 6 Endurance is qualified as per JEDEC Standard 22, Method A117, and measured at −40°C, +25°C, +85°C, and +125°C. 7 The data retention lifetime equivalent is at a junction temperature (TJ) of 85°C as per JEDEC Standard 22, Method A117. Data retention lifetime decreases with junction temperature. 8 These times do not include thermal settling and internal filter response times (330 Hz bandwidth), which may affect overall accuracy. 9 The BARO_OUT and BARO_OUTL registers sample at a rate that is 1/16th that of the other output registers. 10 The sync input clock functions below the specified minimum value, but at reduced performance levels. 2 Rev. A | Page 5 of 24 ADIS16407 TIMING SPECIFICATIONS TA = 25°C, VDD = 5 V, unless otherwise noted. Table 2. Parameter fSCLK tSTALL tREADRATE t tDAV tDSU tDHD tSCLKR, tSCLKF tDR, tDF tSFS t1 tx t2 t3 CS 1 Min 1 0.01 9 40 48.8 Description Serial clock Stall period between data Read rate Chip select to SCLK edge DOUT valid after SCLK edge DIN setup time before SCLK rising edge DIN hold time after SCLK rising edge SCLK rise/fall times, not shown in Timing Diagrams DOUT rise/fall times, not shown in Timing Diagrams CS high after SCLK edge Input sync positive pulse width Input sync low time Input sync to data ready output Input sync period Normal Mode Typ Max 2.0 Min1 0.01 1/fSCLK Burst Read Typ Max 1.0 Unit MHz μs μs ns ns ns ns ns ns ns μs μs μs μs 48.8 100 100 24.4 48.8 24.4 48.8 5 5 12.5 12.5 5 5 5 5 100 12.5 12.5 5 5 100 600 600 910 910 Guaranteed by design and characterization, but not tested in production. Timing Diagrams CS tCS tSFS 1 SCLK 2 3 4 5 6 15 16 tDAV MSB DB14 DB13 tDSU DIN R/W A6 DB12 DB11 A4 A3 DB10 DB2 DB1 LSB tDHD A5 D2 A2 D1 09797-002 DOUT LSB Figure 2. SPI Timing and Sequence tREADRATE tSTALL 09797-003 CS SCLK Figure 3. Stall Time and Data Rate t3 t2 t1 tX 07570-004 SYNC CLOCK (DIO4) DATA READY Figure 4. Input Clock Timing Diagram Rev. A | Page 6 of 24 ADIS16407 ABSOLUTE MAXIMUM RATINGS Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 3. Parameter Acceleration Any Axis, Unpowered Any Axis, Powered VDD to GND Digital Input Voltage to GND Digital Output Voltage to GND Analog Input to GND Temperature Operating Range Storage Range Pressure 1 Rating 2000 g 2000 g −0.3 V to +6.0 V −0.3 V to +5.3 V −0.3 V to +3.6 V −0.3 V to +3.6 V Table 4. Package Characteristics Package Type 24-Lead Module (ML-24-2) −40°C to +105°C −65°C to +125°C1, 2 6 bar Extended exposure to temperatures outside the specified temperature range of −40°C to +105°C can adversely affect the accuracy of the factory calibration. For best accuracy, store the parts within the specified operating range of −40°C to +105°C. 2 Although the device is capable of withstanding short-term exposure to 150°C, long-term exposure threatens internal mechanical integrity. ESD CAUTION Rev. A | Page 7 of 24 θJA 39.8°C/W θJC 14.2°C/W Device Weight 16 grams ADIS16407 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS ADIS16407 DIN DIO1 DIO2 VDD GND GND DNC DNC AUX_ADC DNC 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 DOUT CS RST VDD VDD GND DNC DNC AUX_DAC DNC DNC PIN 23 NOTES 1. THIS VIEW REPRESENTS THE TOP VIEW OF THE MATING CONNECTOR. 2. WHEN CONNECTED, THE PINS ARE NOT VISIBLE. 3. MATING CONNECTOR: SAMTEC CLM-112-02 OR EQUIVALENT. 4. DNC = DO NOT CONNECT. PIN 1 09797-006 SCLK 3 09797-005 DIO3 1 DIO4/CLKIN TOP VIEW (Not to Scale) Figure 6. Axial Orientation Figure 5. Pin Configuration Table 5. Pin Function Descriptions Pin No. 1 2 3 4 5 6 7 8 9 10, 11, 12 13, 14, 15 16, 17, 18, 19, 22, 23, 24 20 21 1 Mnemonic DIO3 DIO4/CLKIN SCLK DOUT DIN CS DIO1 RST DIO2 VDD GND DNC AUX_DAC AUX_ADC Type1 I/O I/O I O I I I/O I I/O S S N/A O I Description Configurable Digital Input/Output. Configurable Digital Input/Output or Sync Clock Input. SPI Serial Clock. SPI Data Output. Clocks the output on the SCLK falling edge. SPI Data Input. Clocks the input on the SCLK rising edge. SPI Chip Select. Configurable Digital Input/Output. Reset. Configurable Digital Input/Output. Power Supply. Power Ground. Do Not Connect. Do not connect to these pins. Auxiliary, 12-Bit DAC Output. Auxiliary, 12-Bit ADC Input. S is supply, O is output, I is input, N/A is not applicable. Rev. A | Page 8 of 24 ADIS16407 TYPICAL PERFORMANCE CHARACTERISTICS ROOT ALLAN VARIANCE (g) 0.01 +1σ 0.01 MEAN –1σ 0.001 +1σ MEAN 0.001 0.1 1 10 100 1k Tau (sec) 10k Figure 7. Gyroscope Root Allan Variance 0.0001 0.1 1 10 100 1k Tau (sec) Figure 8. Accelerometer Root Allan Variance Rev. A | Page 9 of 24 10k 09797-008 –1σ 09797-007 ROOT ALLAN VARIANCE (°/sec) 0.1 ADIS16407 BASIC OPERATION The ADIS16407 is an autonomous system that requires no user initialization. When it has a valid power supply, it initializes itself and starts sampling, processing, and loading sensor data into the output registers at a sample rate of 819.2 SPS. DIO1 pulses high after each sample cycle concludes. The SPI interface enables simple integration with many embedded processor platforms, as shown in Figure 9 (electrical connection) and Table 6 (pin functions). I/O LINES ARE COMPATIBLE WITH 3.3V OR 5V LOGIC LEVELS 5V 10 SYSTEM PROCESSOR SPI MASTER The ADIS16407 provides two different options for acquiring sensor data: single register and burst register. A single register read requires two 16-bit SPI cycles. The first cycle requests the contents of a register using the bit assignments in Figure 13. Bit DC7 to Bit DC0 are don’t care for a read, and then the output register contents follow on DOUT during the second sequence. Figure 10 includes three single register reads in succession. In this example, the process starts with DIN = 0x0400 to request the contents of XGYRO_OUT, then follows with 0x0600 to request YGYRO_OUT and 0x0800 to request ZGYRO_OUT. Full duplex operation enables processors to use the same 16-bit SPI cycle to read data from DOUT while requesting the next set of data on DIN. Figure 11 provides an example of the four SPI signals when reading XGYRO_OUT in a repeating pattern. 11 12 ADIS16407 SS 6 CS SCLK 3 SCLK MOSI 5 DIN MISO 4 DOUT IRQ 7 DIO1 DIN 14 0x0400 15 09797-009 13 DOUT 0x0600 0x0800 XGYRO_OUT YGYRO_OUT ZGYRO_OUT 09797-010 VDD READING SENSOR DATA Figure 10. SPI Read Example Figure 9. Electrical Connection Diagram CS Table 6. Generic Master Processor Pin Names and Functions SCLK Function Slave select Serial clock Master output, slave input Master input, slave output Interrupt request DOUT = 1111 1001 1101 1010 = 0xF9DA = –1574 LSBs => –19.675°/sec Figure 11. Example SPI Read, Second 16-Bit Sequence Burst Read Function The burst read function enables the user to read all output registers using one command on the DIN line and shortens the stall time between each 16-bit segment to one SCLK cycle (see Table 2). Figure 12 provides the burst read sequence of data on each SPI signal. The sequence starts with writing 0x3E00 to DIN, followed by each output register clocking out on DOUT, in the order in which they appear in Table 8. Table 7. Generic Master Processor SPI Settings Description The ADIS16407 operates as a slave Maximum serial clock rate CPOL = 1 (polarity), CPHA = 1 (phase) Bit sequence Shift register/data length CS 1 2 3 15 SCLK DIN 0x3E00 DON’T CARE DOUT SUPPLY_OUT XGYRO_OUT AUX_ADC For burst read, SCLK rate ≤ 1 MHz. Figure 12. Burst Read Sequence CS SCLK DIN DOUT R/W D15 A6 A5 A4 A3 A2 A1 A0 DC7 DC6 DC5 DC4 DC3 DC2 DC1 DC0 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 NOTES 1. THE DOUT BIT PATTERN REFLECTS THE ENTIRE CONTENTS OF THE REGISTER IDENTIFIED BY [A6:A0] IN THE PREVIOUS 16-BIT DIN SEQUENCE WHEN R/W = 0. 2. IF R/W = 1 DURING THE PREVIOUS SEQUENCE, DOUT IS NOT DEFINED. Figure 13. SPI Communication Bit Sequence Rev. A | Page 10 of 24 R/W D15 A6 A5 D14 D13 09797-013 1 09797-011 DOUT The ADIS16407 SPI interface supports full duplex serial communication (simultaneous transmit and receive) and uses the bit sequence shown in Figure 13. Table 7 provides a list of the most common settings that require attention to initialize the serial port of a processor for the ADIS16407 SPI interface. Processor Setting Master SCLK Rate ≤ 2 MHz1 SPI Mode 3 MSB-First Mode 16-Bit Mode DIN = 0000 0100 0000 0000 = 0x0400 DIN 09797-012 Pin Name SS SCLK MOSI MISO IRQ ADIS16407 OUTPUT DATA REGISTERS Table 10. YGYRO_OUT (Base Address = 0x06), Read Only The output registers in Table 8 provide the most recent sensor data produced by the ADIS16407. Each output register has flags for new data indication and error/alarm conditions, which reduces the need to monitor DIAG_STAT. Bits [15] [14] [13:0] Table 8. Output Data Register Formats Register SUPPLY_OUT XGYRO_OUT YGYRO_OUT ZGYRO_OUT XACCL_OUT YACCL_OUT ZACCL_OUT XMAGN_OUT YMAGN_OUT ZMAGN_OUT BARO_OUT BARO_OUTL TEMP_OUT1 AUX_ADC 1 Address 0x02 0x04 0x06 0x08 0x0A 0x0C 0x0E 0x10 0x12 0x14 0x16 0x18 0x1A 0x1C Table 11. ZGYRO_OUT (Base Address = 0x08), Read Only Measurement Power supply Gyroscope, x-axis Gyroscope, y-axis Gyroscope, z-axis Accelerometer, x-axis Accelerometer, y-axis Accelerometer, z-axis Magnetometer, x-axis Magnetometer, y-axis Magnetometer, z-axis Barometer/pressure, higher Barometer/pressure, lower Internal temperature Auxiliary ADC Bits [15] [14] [13:0] Rotation Rate +300°/sec +0.1°/sec +0.05°/sec 0°/sec −0.05°/sec −0.1°/sec −300°/sec mX mY Bits [15] [14] [13:0] aX 09797-014 gX Figure 14. Inertial Sensor Direction Reference Gyroscopes Figure 14 provides arrows (gX, gY, gZ) that indicate the direction of rotation, which produces a positive response in the gyroscope output registers: XGYRO_OUT (x-axis, Table 9), YGYRO_OUT (y-axis, Table 10), and ZGYRO_OUT (z-axis, Table 11). Table 12 illustrates the gyroscope data format. Table 9. XGYRO_OUT (Base Address = 0x04), Read Only Bits [15] [14] [13:0] Binary xx01 0111 0111 0000 xx00 0000 0000 0010 xx00 0000 0000 0001 xx00 0000 0000 0000 xx11 1111 1111 1111 xx11 1111 1111 1110 xx10 1000 1001 0000 Table 13. XACCL_OUT (Base Address = 0x0A), Read Only X-AXIS gY Hex 0x1770 0x0002 0x0001 0x0000 0x3FFF 0x3FFE 0x2890 Figure 14 provides arrows (aX, aY, aZ) that indicate the direction of acceleration, which produces a positive response in the gyroscope output registers: XACCL_OUT (x-axis, Table 13), YACCL_OUT (y-axis, Table 14), and ZACCL_OUT (z-axis, Table 15). Table 16 illustrates the accelerometer data format. mZ gZ aY Decimal +6000 +2 +1 0 −1 −2 −6000 Accelerometers Z-AXIS Y-AXIS Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags Z-axis gyroscope data, twos complement format, 0.05°/sec per LSB, when SENS_AVG[15:8] = 0x04 Table 12. Rotation Rate, Twos Complement Format This is most useful for monitoring relative changes in the temperature. aZ Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags Y-axis gyroscope data, twos complement format, 0.05°/sec per LSB, when SENS_AVG[15:8] = 0x04 Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags X-axis gyroscope data, twos complement format, 0.05°/sec per LSB, when SENS_AVG[15:8] = 0x04 Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags X-axis acceleration data, twos complement format, 0.25 mg per LSB Table 14. YACCL_OUT (Base Address = 0x0C), Read Only Bits [15] [14] [13:0] Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags Y-axis acceleration data, twos complement format, 0.25 mg per LSB Table 15. ZACCL_OUT (Base Address = 0x0E), Read Only Bits [15] [14] [13:0] Rev. A | Page 11 of 24 Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags Z-axis acceleration data, twos complement format, 0.25 mg per LSB ADIS16407 Table 16. Acceleration, Twos Complement Format Acceleration +18 g +6.667 mg +3.333 mg 0g −3.333 mg −6.667 mg −18 g Decimal +5401 +2 +1 0 −1 −2 −5401 Hex 0x1519 0x0002 0x0001 0x0000 0x3FFF 0x3FFE 0x2AE7 Binary xx01 0101 0001 1001 xx00 0000 0000 0010 xx00 0000 0000 0001 xx00 0000 0000 0000 xx11 1111 1111 1111 xx11 1111 1111 1110 xx10 1010 1110 0111 Magnetometers Figure 14 provides arrows (mX, mY, mZ) that indicate the direction of the magnetic field, which produces a positive response in the gyroscope output registers: XMAGN_OUT (x-axis, Table 17), YMAGN_OUT (y-axis, Table 18), and ZAMAGN_OUT (z-axis, Table 19). Table 20 illustrates the magnetic field intensity data format. Use BAR_OUTL and the following steps to increase the numerical resolution by 8-bits for best performance: 1. 2. 3. Read BAR_OUT and multiply by 256 (shift 8 bits) Read BAR_OUTL and max off upper 8 bits Add results together for a 24-bit result, where 1 LSB = 0.0003125 and 0x00000 = 0 mbar Table 21. BARO_OUT (Base Address = 0x16), Read Only Bits [15] [14] [13:0] Table 22. BARO_OUTL (Base Address = 0x18), Read Only Bits [15:8] [7:0] Table 17. XMAGN_OUT (Base Address = 0x10), Read Only Bits [15] [14] [13:0] Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags X-axis magnetic field intensity data, twos complement format, 0.5 mgauss per LSB Table 18. YMAGN_OUT (Base Address = 0x12), Read Only Bits [15] [14] [13:0] Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags Y-axis magnetic field intensity data, twos complement format, 0.5 mgauss per LSB Table 19. ZMAGN_OUT (Base Address = 0x14), Read Only Bits [15] [14] [13:0] Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags Z-axis magnetic field intensity data, twos complement format, 0.5 mgauss per LSB Table 20. Magnetometer, Twos Complement Format Magnetic Field +2.5 gauss +0.001 gauss +0.0005 gauss 0 gauss −0.0005 gauss −0.0005 gauss −2.5 gauss Decimal +5000 +2 +1 0 −1 −2 −5000 Hex 0x1388 0x0002 0x0001 0x0000 0x3FFF 0x3FFE 0x2C78 Binary xx01 0011 1000 1000 xx00 0000 0000 0010 xx00 0000 0000 0001 xx00 0000 0000 0000 xx11 1111 1111 1111 xx11 1111 1111 1110 xx10 1100 0111 1000 Barometric Pressure The barometric pressure measurements are contained in two registers, BARO_OUT (Table 21) and BARO_OUTL (Table 22) registers. Table 23 provides several numerical format examples for BARO_OUT, which is sufficient for most applications. Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags Barometric pressure data, binary data format, 0.08 mbar per LSB, 0x0000 = 0 mbar Description Not used Barometric pressure data, binary data format, 0.0003125 mbar per LSB, 0x0000 = 0 mbar Table 23. Pressure, Binary, BARO_OUT Only Pressure (mbar) 1200 1100 1000 0.16 0.08 0 Decimal 15,000 13,750 12,500 2 1 0 Hex 0x3A98 0x35B6 0x30D4 0x0002 0x0001 0x0000 Binary xx11 1010 1001 1000 xx11 0101 1011 0110 xx11 0000 1101 0100 xx00 0000 0000 0010 xx00 0000 0000 0001 xx00 0000 0000 0000 Internal Temperature The internal temperature measurement data loads into the TEMP_OUT (Table 24) register. Table 25 illustrates the temperature data format. Table 24. TEMP_OUT (Base Address = 0x1A), Read Only Bits [15] [14] [13:12] [11:0] Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags Not used Internal temperature data, twos complement, 0.136°C/LSB, 25°C = 0x000 Table 25. Temperature, Twos Complement Format Temperature +105°C +85°C +25.272°C +25.136°C +25°C +24.864°C +24.728°C −40°C Rev. A | Page 12 of 24 Decimal +588 LSB +441 LSB +2 LSB +1 LSB 0 LSB −1 LSB −2 LSB −478 LSB Hex 0x24C 0x1B9 0x002 0x001 0x000 0xFFF 0xFFE 0xE22 Binary xxxx 0010 0100 1100 xxxx 0001 1011 1001 xxxx 0000 0000 0010 xxxx 0000 0000 0001 xxxx 0000 0000 0000 xxxx 1111 1111 1111 xxxx 1111 1111 1110 xxxx 1110 0010 0010 ADIS16407 Power Supply Table 29. Analog Input, Offset Binary Format The SUPPLY_OUT register (Table 26) provides a measurement of the voltage that is on the VDD pins of the device. Table 27 illustrates the power supply data format. Input Voltage 3.3 V 1V 1.6118 mV 805.9 μV 0V Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags Not used Power supply measurement data, binary format, 2.418 mV/LSB, 0 V = 0x000 Table 27. Power Supply Data, Binary Format Voltage +5.25 V +5.0 V +4.75 V 1V 4.836 mV 2.418 mV 0V Decimal 2171 2068 1964 414 2 1 0 Hex 0x87B 0x814 0x7AC 0x19E 0x002 0x001 0x000 Binary xxxx 1000 0111 1011 xxxx 1000 0001 0100 xxxx 0111 1010 1100 xxxx 0001 1001 1110 xxxx 0000 0000 0010 xxxx 0000 0000 0001 xxxx 0000 0000 0000 DEVICE CONFIGURATION The control registers in Table 30 provide users with a variety of configuration options. The SPI provides access to these registers, one byte at a time, using the bit assignments in Figure 13. Each register has 16 bits, where Bits[7:0] represent the lower address, and Bits[15:8] represent the upper address. Figure 16 provides an example of writing 0x03 to Address 0x3B (SMPL_PRD[15:8]), using DIN = 0xBB03. This example reduces the sample rate by a factor of eight (see Table 46). CS SCLK DIN DIN = 1011 1011 0000 0011 = 0xBB03, WRITES 0x03 TO ADDRESS 0x3B. Figure 16. Example SPI Write Sequence INPUT ADC CHANNEL The AUX_ADC register provides access to the auxiliary ADC input channel. The ADC is a 12-bit successive approximation converter that has an input circuit equivalent to the one shown in Figure 15. The maximum input is 3.3 V. The ESD protection diodes can handle 10 mA without causing irreversible damage. The on resistance (R1) of the switch has a typical value of 100 Ω. The sampling capacitor, C2, has a typical value of 16 pF. VCC D R1 C2 09797-015 D C1 Figure 15. Equivalent Analog Input Circuit (Conversion Phase: Switch Open, Track Phase: Switch Closed) Dual Memory Structure Writing configuration data to a control register updates its SRAM contents, which are volatile. After optimizing each relevant control register setting in a system, set GLOB_CMD[3] = 1 (DIN = 0xBE08) to backup these settings in nonvolatile flash memory. The flash backup process requires a valid power supply level for the entire 75 ms process time. Table 30 provides a user register memory map that includes a flash backup column. A “yes” in this column indicates that a register has a mirror location in flash and, when backed up properly, it automatically restores itself during startup or after a reset. Figure 17 provides a diagram of the dual memory structure used to manage operation and store critical user settings. MANUAL FLASH BACKUP Table 28. AUX_ADC (Base Address = 0x1C), Read Only Bits [15] [14] [13:12] [11:0] Binary xxxx 1111 1111 1111 xxxx 0100 1101 1001 xxxx 0000 0000 0010 xxxx 0000 0000 0001 xxxx 0000 0000 0000 Description New data indicator (ND), 1 = new data in register Error/alarm, 1 = active, see DIAG_STAT for error flags Not used Analog input channel data, binary format, 0.8059 mV/LSB, 0 V = 0x000 Rev. A | Page 13 of 24 NONVOLATILE FLASH MEMORY VOLATILE SRAM (NO SPI ACCESS) SPI ACCESS START-UP RESET Figure 17. SRAM and Flash Memory Diagram 09797-017 Bits [15] [14] [13:12] [11:0] Hex 0xFFF 0x4D9 0x002 0x001 0x000 09797-016 Table 26. SUPPLY_OUT (Base Address = 0x02), Read Only Decimal 4095 1241 2 1 0 ADIS16407 USER REGISTERS Table 30. User Register Memory Map 1 Name FLASH_CNT SUPPLY_OUT XGYRO_OUT YGYRO_OUT ZGYRO_OUT XACCL_OUT YACCL_OUT ZACCL_OUT XMAGN_OUT YMAGN_OUT ZMAGN_OUT BARO_OUT BARO_OUTL TEMP_OUT AUX_ADC XGYRO_OFF YGYRO_OFF ZGYRO_OFF XACCL_OFF YACCL_OFF ZACCL_OFF XMAGN_HIC YMAGN_HIC ZMAGN_HIC XMAGN_SIC YMAGN_SIC ZMAGN_SIC GPIO_CTRL MSC_CTRL SMPL_PRD SENS_AVG SLP_CTRL DIAG_STAT GLOB_CMD ALM_MAG1 ALM_MAG2 ALM_SMPL1 ALM_SMPL2 ALM_CTRL AUX_DAC Reserved LOT_ID1 LOT_ID2 PROD_ID SERIAL_NUM 1 2 R/W R R R R R R R R R R R R R R R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W W R W R/W R/W R/W R/W R/W R/W N/A R R R R Flash Backup Yes No No No No No No No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes No No N/A Yes Yes Yes Yes Yes No N/A Yes Yes Yes Yes Address 2 0x00 0x02 0x04 0x06 0x08 0x0A 0x0C 0x0E 0x10 0x12 0x14 0x16 0x18 0x1A 0x1C 0x1E 0x20 0x22 0x24 0x26 0x28 0x2A 0x2C 0x2E 0x30 0x32 0x34 0x36 0x38 0x3A 0x3C 0x3E 0x40 0x42 0x44 0x46 0x48 0x4A 0x4C 0x4E 0x50 0x52 0x54 0x56 0x58 Default N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0800 0x0800 0x0800 0x0000 0x0006 0x0001 0x0402 N/A 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 N/A N/A N/A 0x4107 N/A Function Flash memory write count Power supply measurement X-axis gyroscope output Y-axis gyroscope output Z-axis gyroscope output X-axis accelerometer output Y-axis accelerometer output Z-axis accelerometer output X-axis magnetometer measurement Y-axis magnetometer measurement Z-axis magnetometer measurement Barometer pressure measurement, high word Barometer pressure measurement, low word Temperature output Auxiliary ADC measurement X-axis gyroscope bias offset factor Y-axis gyroscope bias offset factor Z-axis gyroscope bias offset factor X-axis acceleration bias offset factor Y-axis acceleration bias offset factor Z-axis acceleration bias offset factor X-axis magnetometer, hard iron factor Y-axis magnetometer, hard iron factor Z-axis magnetometer, hard iron factor X-axis magnetometer, soft iron factor Y-axis magnetometer, soft iron factor Z-axis magnetometer, soft iron factor Auxiliary digital input/output control Miscellaneous control Internal sample period (rate) control Dynamic range and digital filter control Sleep mode control System status System command Alarm 1 amplitude threshold Alarm 2 amplitude threshold Alarm 1 sample size Alarm 2 sample size Alarm control Auxiliary DAC data Reserved Lot identification number Lot identification number Product identifier Bit Assignments See Table 38 See Table 26 See Table 9 See Table 10 See Table 11 See Table 13 See Table 14 See Table 15 See Table 17 See Table 18 See Table 19 See Table 21 See Table 22 See Table 24 See Table 28 See Table 49 See Table 50 See Table 51 See Table 52 See Table 53 See Table 54 See Table 55 See Table 56 See Table 57 See Table 58 See Table 59 See Table 60 See Table 42 See Table 39 See Table 46 See Table 47 See Table 33 See Table 40 See Table 32 See Table 62 See Table 63 See Table 64 See Table 65 See Table 66 See Table 43 See Table 34 See Table 35 See Table 36 See Table 37 N/A means not applicable. Each register contains two bytes. The address of the lower byte is displayed. The address of the upper byte is equal to the address of the lower byte plus 1. Rev. A | Page 14 of 24 ADIS16407 SYSTEM FUNCTIONS The ADIS16407 provides a number of system level controls for managing its operation, using the registers in Table 31. Table 31. System Tool Registers Register Name MSC_CTRL SLP_CTRL DIAG_STAT GLOB_CMD LOT_ID1 LOT_ID2 PROD_ID SERIAL_NUM Address 0x38 0x3E 0x40 0x42 0x52 0x54 0x56 0x58 Description Self test, calibration, data ready Sleep mode control Error flags Single command functions Lot Identification Code 1 Lot Identification Code 2 Product identifier Serial number GLOBAL COMMANDS The GLOB_CMD register in Table 32 provides trigger bits for software reset, flash memory management, DAC control, and calibration control. Start each of these functions by writing a 1 to the assigned bit in GLOB_CMD. After completing the task, the bit automatically returns to 0. For example, set GLOB_CMD[7] = 1 (DIN = 0xC280) to initiate a software reset, which stops the sensor operation and runs the device through its start-up sequence. Set GLOB_CMD[3] = 1 (DIN = 0xC208) to back up the user register contents in nonvolatile flash. This sequence includes loading the control registers with the data in their respective flash memory locations prior to producing new data. Table 32. GLOB_CMD (Base Address = 0x42), Write Only Bits [15:8] [7] [6:4] [3] [2] [1] [0] Description (Default = 0x0000) Not used Software reset Not used Flash update Auxiliary DAC data latch Factory calibration restore Gyroscope bias correction Description Not used Normal sleep mode (1 = start sleep mode) Timed sleep mode (write 0x01 to 0xFF to start) Sleep mode duration, binary, 0.5 sec/LSB Table 34. LOT_ID1 (Base Address = 0x52), Read Only Bits [15:0] Description Lot identification, binary code Table 35. LOT_ID2 (Base Address = 0x54), Read Only Bits [15:0] Description Lot identification, binary code Table 36. PROD_ID Bit (Base Address = 0x56), Read Only Bits [15:0] Description (Default = 0x4017) Product identification = 0x4017 Table 37. SERIAL_NUM (Base Address = 0x58), Read Only Bits [15:12] [11:0] Description Reserved Serial number, 1 to 4094 (0xFFE) MEMORY MANAGEMENT Table 38. FLASH_CNT (Base Address = 0x00), Read Only The SLP_CTRL register (see Table 33) provides two sleep modes for system level management: normal and timed. Set SLP_CTRL[8] = 1 (DIN = 0xBF01) to start normal sleep mode. When the device is in sleep mode, the following events can cause it to wake up: asserting CS from high to low, asserting RST from high to low, or cycling the power. Use SLP_CTRL[7:0] to put the device into sleep mode for a specified period. For example, SLP_CNT[7:0] = 0x64 (DIN = 0xBE64) puts the ADIS16407 to sleep for 50 seconds. Table 33. SLP_CTRL (Base Address = 0x3E), Write Only The PROD_ID register in Table 36 contains the binary equivalent of 16,407. It provides a product specific variable for systems that need to track this in their system software. The LOT_ID1 and LOT_ID2 registers in Table 34 and Table 35 combine to provide a unique, 32-bit lot identification code. The SERIAL_NUM register in Table 37 contains a binary number that represents the serial number on the device label. The assigned serial numbers in SERIAL_NUM are lot specific. The FLASH_CNT register in Table 38 provides a 16-bit counter that helps track the number of write cycles to the nonvolatile flash memory. The flash updates every time a manual flash update occurs. A manual flash update is initiated by the GLOB_CMD[3] bit and is also performed at the completion of the GLOB_CMD[1:0] functions (see Table 32). POWER MANAGEMENT Bits [15:9] [8] [7:0] PRODUCT IDENTIFICATION Bits [15:0] Description Binary counter Checksum Test Set MSC_CTRL[11] = 1 (DIN = 0xB908) to perform a checksum test of the internal program memory. This function takes a summation of the internal program memory and compares it with the original summation value for the same locations (from factory configuration). Check the results in the DIAG_STAT register, which is in Table 40. DIAG_STAT[6] equals 0 if the sum matches the correct value, and 1 if it does not. Make sure that the power supply is within specification for the entire 20 ms that this function takes to complete. Rev. A | Page 15 of 24 ADIS16407 SELF TEST FUNCTION STATUS/ERROR FLAGS The MSC_CTRL register in Table 39 provides a self test function for the gyroscopes and accelerometers. This function allows the user to verify the mechanical integrity of each MEMS sensor. When enabled, the self test applies an electrostatic force to each internal sensor element, which causes them to move. The movement in each element simulates its response to actual rotation/ acceleration and generates a predictable electrical response in the sensor outputs. The ADIS16407 exercises this function and compares the response to an expected range of responses and reports a pass/fail response to DIAG_STAT[5]. If this is high, the DIAG_STAT[15:10] provide pass/fail flags for each inertial sensor. The DIAG_STAT register in Table 40 provides error flags for a number of functions. Each flag uses 1 to indicate an error condition and 0 to indicate a normal condition. Reading this register provides access to the status of each flag and resets all of the bits to 0 for monitoring future operation. If the error condition remains, the error flag returns to 1 at the conclusion of the next sample cycle. DIAG_STAT[0] does not require a read of this register to return to 0. If the power supply voltage goes back into range, this flag clears automatically. The SPI communication error flag in DIAG_STAT[3] indicates that the number of SCLKs in a SPI sequence did not equal a multiple of 16 SCLKs. Table 39. MSC_CTRL (Base Address = 0x38), Read/Write Table 40. DIAG_STAT (Base Address = 0x40), Read Only Bits [15:12] [11] Bits [15] [10] [9:8] [7] [6] [5:3] [2] [1] [0] 1 Description (Default = 0x0006) Not used Checksum memory test (cleared upon completion)1 1 = enabled, 0 = disabled Internal self test (cleared upon completion)1 1 = enabled, 0 = disabled Do not use, always set to 00 Linear acceleration bias compensation for gyroscopes 1 = enabled, 0 = disabled Point of percussion, see Figure 6 1 = enabled, 0 = disabled Not used Data ready enable 1 = enabled, 0 = disabled Data ready polarity 1 = active high, 0 = active low Data ready line select 1 = DIO2, 0 = DIO1 The bit is automatically reset to 0 after finishing the test. [14] [13] [12] [11] [10] [9] [8] [7] [6] [5] [4] [3] [2] [1] [0] Rev. A | Page 16 of 24 Description (Default = 0x0000) Z-axis accelerometer self test failure 1 = fail, 0 = pass Y-axis accelerometer self test failure 1 = fail, 0 = pass X-axis accelerometer self test failure 1 = fail, 0 = pass Z-axis gyroscope self test failure 0 = pass Y-axis gyroscope self test failure 1 = fail, 0 = pass X-axis gyroscope self test failure 1 = fail, 0 = pass Alarm 2 status 1 = active, 0 = inactive Alarm 1 status 1 = active, 0 = inactive Not used Flash test, checksum flag 1 = fail, 0 = pass Self test diagnostic error flag 1 = fail, 0 = pass Sensor overrange 1 = overrange, 0 = normal SPI communication failure 1 = fail, 0 = pass Flash update failure 1 = fail, 0 = pass Power supply high 1 = VDD > 5.25 V 0 = VDD ≤ 5.25 V Power supply low 1 = VDD < 4.75 V 0 = VDD ≥ 4.75 V ADIS16407 INPUT/OUTPUT CONFIGURATION Table 41 provides a summary of registers that provide input/output configuration and control. Table 41. Input/Output Registers Register Name GPIO_CTRL MSC_CTRL AUX_DAC Address 0x36 0x38 0x4E Description General-purpose I/O control Self test, calibration, data ready Output voltage control, AUX_DAC DATA READY INPUT/OUTPUT INDICATOR GENERAL-PURPOSE INPUT/OUTPUT DIO1, DIO2, DIO3, and DIO4 are configurable, general-purpose input/output lines that serve multiple purposes. The data ready controls in MSC_CTRL[2:0] have the highest priority for configuring DIO1 and DIO2. The alarm indicator controls in ALM_CTRL[2:0] have the second highest priority for configuring DIO1 and DIO2. The external clock control associated with SMPL_PRD[0] has the highest priority for DIO4 configuration (see Table 46). GPIO_CTRL in Table 42 has the lowest priority for configuring DIO1, DIO2, and DIO4, and has absolute control over DIO3. Table 42. GPIO_CTRL (Base Address = 0x36), Read/Write [2] [1] [0] For example, set GPIO_CTRL[3:0] = 0100 (DIN = 0xB604) to set DIO3 as an output signal pin and DIO1, DIO2, and DIO4 as input signal pins. Set the output on DIO3 to 1 by setting GPIO_CTRL[10] = 1 (DIN = 0xB704). Then, read GPIO_CTRL[7:0] (DIN = 0x3600) and mask off GPIO_CTRL[9:8] and GPIO_CTRL[11] to monitor the digital signal levels on DIO4, DIO2, and DIO1. AUXILIARY DAC The factory default setting of MSC_CTRL[2:0] = 110 establishes DIO1 as a positive polarity data ready signal. See Table 39 for additional data ready configuration options. For example, set MSC_CTRL[2:0] = 100 (DIN = 0xB804) to change the polarity of the data ready signal on DIO1 for interrupt inputs that require negative logic inputs for activation. The pulse width is typically between 60 μs and 150 μs, including jitter (±30 μs). Bits [15:12] [11] [10] [9] [8] [7:4] [3] Example Input/Output Configuration Description (Default = 0x0000) Not used General-Purpose I/O Line 4 (DIO4) data level General-Purpose I/O Line 3 (DIO3) data level General-Purpose I/O Line 2 (DIO2) data level General-Purpose I/O Line 1 (DIO1) data level Not used General-Purpose I/O Line 4 (DIO4) direction control 1 = output, 0 = input General-Purpose I/O Line 3 (DIO3) direction control 1 = output, 0 = input General-Purpose I/O Line 2 (DIO2) direction control 1 = output, 0 = input General-Purpose I/O Line 1 (DIO1) direction control 1 = output, 0 = input The AUX_DAC register in Table 43 provides user controls for setting the output voltage on the AUX_DAC pin. The 12-bit AUX_DAC line can drive its output to within 5 mV of the ground reference when it is not sinking current. As the output approaches 0 V, the linearity begins to degrade (~100 LSB starting point). As the sink current increases, the nonlinear range increases. The DAC latch command in GLOB_CMD[2] (see Table 32) moves the values of the AUX_DAC register into the DAC input register, enabling both bytes to take effect at the same time. This prevents undesirable output levels, which reflect single byte changes of the AUX_DAC register. Table 43. AUX_DAC (Base Address = 0x4E), Read/Write Bits [15:12] [11:0] Description (Default = 0x0000) Not used Data bits, scale factor = 0.8059 mV/LSB, offset binary format, 0 V = 0 LSB Table 44. Setting AUX_DAC = 1 V DIN 0xCED9 0xCF04 0xC204 Rev. A | Page 17 of 24 Description AUX_DAC[7:0] = 0xD9 (217 LSB) AUX_DAC[15:8] = 0x04 (1024 LSB) GLOB_CMD[2] = 1; move values into the DAC input register, resulting in a 1 V output level ADIS16407 DIGITAL PROCESSING CONFIGURATION 0 Table 45. Digital Processing Registers Description Sample rate control Digital filtering and range control –20 –40 SAMPLE RATE The internal sampling system produces new data in the output data registers at a rate of 819.2 SPS. The SMPL_PRD register in Table 46 provides two functional controls that affect sampling and register update rates. SMPL_PRD[12:8] provides a control for reducing the update rate, using an averaging filter with a decimated output. These bits provide a binomial control that divides the data rate by a factor of 2 every time this number increases by 1. For example, set SMPL_PRD[15:8] = 0x04 (DIN = 0xBB04) to set the decimation factor to 16. This reduces the update rate to 51 SPS and the bandwidth to 25 Hz. –80 –100 –140 0.001 0.1 FREQUENCY (f/fS) 1 Figure 18. Bartlett Window, FIR Filter Frequency Response (Phase Delay = N Samples) DYNAMIC RANGE The SENS_AVG[10:8] bits provide three dynamic range settings for this gyroscope. The lower dynamic range settings (±75°/sec and ±150°/sec) limit the minimum filter tap sizes to maintain resolution. For example, set SENS_AVG[10:8] = 010 (DIN = 0xBD02) for a measurement range of ±150°/sec. Because this setting can influence the filter settings, program SENS_AVG[10:8] before programming SENS_AVG[2:0] if more filtering is required. Description (Default = 0x0001) Not used D, decimation rate setting, binomial, see Figure 19 Not used Clock 1 = internal 819.2 SPS 0 = external Table 47. SENS_AVG (Base Address = 0x3C), Read/Write INPUT CLOCK CONFIGURATION Bits [15:11] [10:8] SMPL_PRD[0] provides a control for synchronizing the internal sampling to an external clock source. Set SMPL_PRD[0] = 0 (DIN = 0xBA00) and GPIO_CTRL[3] = 0 (DIN = 0xB600) to enable the external clock. See Table 2 and Figure 4 for timing information. DIGITAL FILTERING Description (Default = 0x0402) Not used Measurement range (sensitivity) selection 100 = ±300°/sec (default condition) 010 = ±150°/sec, filter taps ≥ 4 (Bits[2:0] ≥ 0x02) 001 = ±75°/sec, filter taps ≥ 16 (Bits[2:0] ≥ 0x04) Not used Filter Size Variable B Number of taps in each stage; NB = 2B See Figure 18 for filter response [7:3] [2:0] The SENS_AVG register in Table 47 provides user controls for the low-pass filter. This filter contains two cascaded averaging filters that provide a Bartlett window, FIR filter response (see Figure 19). For example, set SENS_AVG[2:0] = 100 (DIN = 0xBC04) to set each stage to 16 taps. When used with the default sample rate of 819.2 SPS and zero decimation (SMPL_PRD[15:8] = 0x00), this value reduces the sensor bandwidth to approximately 16 Hz. BARTLETT WINDOW FIR FILTER MEMS SENSOR 0.01 09797-018 N=2 N=4 N = 16 N = 64 –120 Table 46. SMPL_PRD (Base Address = 0x3A), Read/Write Bits [15:13] [12:8] [7:1] [0] –60 LOW-PASS FILTER 330Hz 1 NB ADC GYROSCOPES LOW-PASS, TWO-POLE (404Hz, 757Hz) ACCELEROMETERS LOW-PASS, SINGLE-POLE (330Hz) CLOCK 819.2SPS NB x(n) n=1 1 NB NB x(n) n=1 B = SENS_AVG[2:0] NB = 2B NB = NUMBER OF TAPS (PER STAGE) AVERAGE/ DECIMATION FILTER 1 ND ÷ND x(n) n=1 D = SMPL_PRD[12:8] ND = 2D ND = NUMBER OF TAPS EXTERNAL CLOCK ENABLED BY SMPL_PRD[0] = 0 Figure 19. Sampling and Frequency Response Block Diagram Rev. A | Page 18 of 24 ND 09797-019 Address 0x3A 0x3C MAGNITUDE (dB) Register Name SMPL_PRD SENS_AVG ADIS16407 CALIBRATION The mechanical structure and assembly process of the ADIS16407 provide excellent position and alignment stability for each sensor, even after subjected to temperature cycles, shock, vibration, and other environmental conditions. The factory calibration includes a dynamic characterization of each gyroscope and accelerometer over temperature and generates sensor specific correction formulas. Table 48 provides a list of registers that can help optimize system performance after installation. Figure 20 illustrates the summing function for the offset correction register of each sensor. Table 49. XGYRO_OFF (Base Address = 0x1E), Read/Write Bits [15:14] [13:0] Table 50. YGYRO_OFF (Base Address = 0x20), Read/Write Bits [15:14] [13:0] Table 48. Registers for User Calibration Register XGYRO_OFF YGYRO_OFF ZGYRO_OFF XACCL_OFF YACCL_OFF ZACCL_OFF XMAGN_HIC YMAGN_HIC ZMAGN_HIC XMAGN_SIC YMAGN_SIC ZMAGN_SIC MSC_CTRL GLOB_CMD Address 0x1E 0x20 0x22 0x24 0x26 0x28 0x2A 0x2C 0x2E 0x30 0x32 0x34 0x38 0x42 Description Gyroscope bias, x-axis Gyroscope bias, y-axis Gyroscope bias, z-axis Accelerometer bias, x-axis Accelerometer bias, y-axis Accelerometer bias, z-axis Hard iron correction, x-axis Hard iron correction, y-axis Hard iron correction, z-axis Soft iron correction, x-axis Soft iron correction, y-axis Soft iron correction, z-axis Miscellaneous calibration Automatic calibration Bits [15:14] [13:0] When the bias estimate is complete, multiply the estimate by −1 to change its polarity, convert it into digital format for the offset correction registers (Table 49), and write the correction factors to the correction registers. For example, lower the x-axis bias by 10 LSB (0.125°/sec) by setting XGYRO_OFF = 0x1FF6 (DIN = 0x9F1F, 0x9EF6). Single Command Bias Correction GLOB_CMD[0] (Table 32) loads the xGYRO_OFF registers with the values that are the opposite of the values that are in xGYRO_OUT, at the time of initiation. Use this command, together with the decimation filter (SMPL_PRD[12:8], Table 46), to automatically average the gyroscope data and improve the accuracy of this function, as follows: 1. 2. XGYRO_OUT XGYRO_OFF 09797-020 ADC Description (Default = 0x0000) Not used Z-axis, gyroscope offset correction factor, twos complement, 0.0125°/sec per LSB Gyroscope Bias Correction Factors The XGYRO_OUT (Table 49), YGYRO_OUT (Table 50), and ZGYRO_OUT (Table 51) registers provide user-programmable bias adjustment function for the x-, y-, and z-axis gyroscopes, respectively. Figure 20 illustrates that they contain bias correction factors that adjust to the sensor data immediately before it loads into the output register. FACTORY CALIBRATION AND FILTERING Description (Default = 0x0000) Not used Y-axis, gyroscope offset correction factor, twos complement, 0.0125°/sec per LSB Table 51. ZGYRO_OFF (Base Address = 0x22), Read/Write GYROSCOPES X-AXIS MEMS GYRO Description (Default = 0x0000) Not used X-axis, gyroscope offset correction factor, twos complement, 0.0125°/sec per LSB 3. 4. Figure 20. User Calibration, XGYRO_OFF Example Gyroscope Bias Error Estimation Any system level calibration function must start with an estimate of the bias errors, which typically comes from a sample of gyroscope output data, when the device is not in motion. The sample size of data depends on the accuracy goals. Figure 7 provides a trade-off relationship between averaging time and the expected accuracy of a bias measurement. Vibration, thermal gradients, and power supply instability can influence the accuracy of this process. Rev. A | Page 19 of 24 Set SENS_AVG[10:8] = 001 (DIN = 0xBD01) to optimize the xGYRO_OUT sensitivity to 0.0125°/sec/LSB. Set SMPL_PRD[12:8] = 0x10 (DIN = 0xBB10) to set the decimation rate to 65,536 (216), which provides an averaging time of 80 seconds (65,536 ÷ 819.2 SPS). Wait for 80 seconds while keeping the device motionless. Set GLOB_CMD[0] = 1 (DIN = 0xC201) and wait for the time it takes to perform the flash memory backup (~75 ms). ADIS16407 ACCELEROMETERS The XACCL_OUT (Table 52), YACCL_OUT (Table 53), and ZACCL_OUT (Table 54) registers provide user programmable bias adjustment function for the x-, y-, and z-axis accelerometers, respectively. These registers adjust the accelerometer data in the same manner as XGYRO_OFF functions in Figure 20. Bits [15:14] [13:0] Description (Default = 0x0000) Not used X-axis, accelerometer offset correction factor, twos complement, 0.25 mg/LSB ORIGIN ALIGNMENT REFERENCE POINT SEE MSC_CTRL[6]. Figure 21. Point of Percussion Physical Reference Table 53. YACCL_OFF (Base Address = 0x26), Read/Write Bits [15:14] [13:0] 09797-021 Table 52. XACCL_OFF (Base Address = 0x24), Read/Write MAGNETOMETER CALIBRATION Description (Default = 0x0000) Not used Y-axis, accelerometer offset correction factor, twos complement, 0.25 mg/LSB The ADIS16407 provides registers that contribute to both hard iron and soft iron correction factors, as shown in Figure 22 XMAGN_SIC Table 54. ZACCL_OFF (Base Address = 0x28), Read/Write Description (Default = 0x0000) Not used Z-axis, accelerometer offset correction factor, twos complement, 0.25 mg/LSB MAGNETIC SENSOR ADC FACTORY CALIBRATION AND FILTERING + × XMAGN_OUT XMAGN_HIC 09797-022 Bits [15:14] [13:0] Figure 22. Hard Iron and Soft Iron Factor Correction Accelerometer Bias Error Estimation Under static conditions, orient each accelerometer in positions where the response to gravity is predictable. A common approach to this is to measure the response of each accelerometer when they are oriented in peak response positions, that is, where ±1 g is the ideal measurement position. Next, average the +1 g and −1 g accelerometer measurements together to estimate the residual bias error. Using more points in the rotation can improve the accuracy of the response. Accelerometer Bias Correction Factors When the bias estimate is complete, multiply the estimate by −1 to change its polarity, convert it to the digital format for the offset correction registers (Table 52), and write the correction factors to the correction registers. For example, lower the x-axis bias by 10 LSB (33.3 mg) by setting XACCL_OFF = 0x1FF6 (DIN = 0xA51F, 0xA4F6). Hard Iron Correction The XMAGN_HIC (Table 55), YMAGN_HIC (Table 56), and ZMAGN_HIC (Table 57) registers provide the user programmable bias adjustment function for the x-, y-, and z-axis magnetometers, respectively. Hard iron effects result in an offset of the magnetometer response. Table 55. XMAGN_HIC (Base Address = 0x2A), Read/Write Bits [15:14] [13:0] Table 56. YMAGN_HIC (Base Address = 0x2C), Read/Write Bits [15:14] [13:0] Point of Percussion Alignment Set MSC_CTRL[6] = 1 (DIN = 0xB846) to enable this feature and maintain the factory default settings for DIO1. This feature performs a point of percussion translation to the point identified in Figure 21. See Table 39 for more information on MSC_CTRL. Description (Default = 0x0800) Not used X-axis hard iron correction factor, twos complement, 0.5 mgauss/LSB Description (Default = 0x0800) Not used Y-axis hard iron correction factor, twos complement, 0.5 mgauss/LSB Table 57. ZMAGN_HIC (Base Address = 0x2E), Read/Write Bits [15:14] [13:0] Rev. A | Page 20 of 24 Description (Default = 0x0800) Not used Z-axis hard iron correction factor, twos complement, 0.5 mgauss/LSB ADIS16407 Hard Iron Factors Soft Iron Factors When the hard iron error estimation is complete, take the following steps: When the soft iron error estimation is complete, convert the sensitivity into the digital format for the soft iron correction registers (Table 58) and write the correction factors to the correction registers. A simple method for converting the correction factor is to divide it by 2 and multiply it by 4095. For example, increasing the default soft iron factor to approximately 1.15 uses a binary code for 2355, or 0x933. Increase the soft iron correction factor for the y-axis to approximately 1.15 by setting YMAGN_SIC = 0x0933 (DIN = 0xB309, 0xB233). 1. 2. 3. Multiply the estimate by −1 to change its polarity. Convert it into digital format for the hard iron correction registers (Table 55). Write the correction factors to the correction registers. For example, lower the x-axis bias by 10 LSB (5 mgauss) by setting XMAGN_HIC = 0x1FF6 (DIN = 0xAB1F, 0xAAF6). Soft Iron Effects FLASH UPDATES The XMAGN_SIC (Table 58), YMAGN_SIC (Table 59), and ZMAGN_SIC (Table 60) registers provide an adjustment variable for the magnetometer sensitivity adjustment in each magnetometer response to simplify the process of performing a system level soft iron correction. When using the user calibration registers to optimize system level accuracy, keep in mind that the register values are volatile until their contents are saved in the nonvolatile flash memory. After writing all of the correction factors into the user correction registers, set GLOB_CMD[3] = 1 (DIN = 0xC204) to save these settings in nonvolatile flash memory. Be sure to consider the endurance rating of the flash memory when determining how often to update the user correction factors in the flash memory. Table 58. XMAGN_SIC (Base Address = 0x30), Read/Write Bits [15:12] [11:0] Description (Default = 0x0000) Not used X-axis soft iron correction factor, binary format, 2 = 0xFFF, 1 = 0x800, 0 = 0x000, ~0.0488%/LSB RESTORING FACTORY CALIBRATION Table 59. YMAGN_SIC (Base Address = 0x32), Read/Write Bits [15:12] [11:0] Description (Default = 0x0000) Not used Y-axis soft iron correction factor, binary format, 2 = 0xFFF, 1 = 0x800, 0 = 0x000, ~0.0488%/LSB Set GLOB_CMD[1] = 1 (DIN = 0xC202) to execute the factory calibration restore function. This is a single command function, which resets the gyroscope and accelerometer offset registers to 0x0000 and all sensor data to 0. Then, it automatically updates the flash memory within 75 ms and restarts sampling and processing data. See Table 32 for more information on GLOB_CMD. Table 60. ZMAGN_SIC (Base Address = 0x34), Read/Write Bits [15:12] [11:0] Description (Default = 0x0000) Not used Z-axis soft iron correction factor, binary format, 2 = 0xFFF, 1 = 0x800, 0 = 0x000, ~0.0488%/LSB Rev. A | Page 21 of 24 ADIS16407 ALARMS Alarm 1 and Alarm 2 provide two independent alarms. Table 61 lists the alarm control registers, including ALM_CTRL (Table 66), which provides control bits for data source selection, static/ dynamic comparison, filtering, and alarm indicator. ALARM REPORTING Table 61. Registers for Alarm Configuration Table 66. ALM_CTRL (Base Address = 0x4C), Read/Write Register ALM_MAG1 ALM_MAG2 ALM_SMPL1 ALM_SMPL2 ALM_CTRL Bits [15:12] Address 0x44 0x46 0x48 0x4A 0x4C Description Alarm 1 trigger setting Alarm 2 trigger setting Alarm 1 sample period Alarm 2 sample period Alarm configuration The DIAG_STAT[9:8] bits provide error flags that indicate an alarm condition. The ALM_CTRL[2:0] bits provide controls for a hardware indicator using DIO1 or DIO2. STATIC ALARM USE The static alarms setting compares the data source selection (ALM_CTRL[15:8]) with the values in the ALM_MAGx registers listed in Table 62 and Table 63, using ALM_MAGx[15] to determine the trigger polarity. The data format in these registers matches the format of the data selection in ALM_CTRL[15:8]. See Table 67, Alarm 1, for a static alarm configuration example. Table 62. ALM_MAG1 (Base Address = 0x44), Read/Write Bits [15] [14] [13:0] Description (Default = 0x0000) Trigger polarity 1 = greater than, 0 = less than Not used Threshold setting; matches for format of ALM_CTRL[11:8] output register selection Table 63. ALM_MAG2 (Base Address = 0x46), Read/Write Bits [15] [14] [13:0] Description (Default = 0x0000) Trigger polarity 1 = greater than, 0 = less than Not used Threshold setting; matches for format of ALM_CTRL[15:12] output register selection [11:8] [7] [6] [5] [4] [3] [2] [1] [0] Alarm Example DYNAMIC ALARM USE The dynamic alarm setting monitors the data selection for a rate-of-change comparison. The rate-of-change comparison is represented by the magnitude in the ALM_MAGx registers over the time represented by the number-of-samples setting in the ALM_SMPLx registers, located in Table 64. See Table 67, Alarm 2, for a dynamic alarm configuration example. Table 67 offers an example that configures Alarm 1 to trigger when filtered ZACCL_OUT data drops below 0.7 g, and Alarm 2 to trigger when filtered ZGYRO_OUT data changes by more than 50°/sec over a 100 ms period, or 500°/sec2. The filter setting helps reduce false triggers from noise and refine the accuracy of the trigger points. The ALM_SMPL2 setting of 82 samples provides a comparison period that is approximately equal to 100 ms for an internal sample rate of 819.2 SPS. Table 67. Alarm Configuration Example 1 DIN 0xCD47, 0xCC97 Table 64. ALM_SMPL1 (Base Address = 0x48), Read/Write Bits [15:8] [7:0] Description (Default = 0x0000) Not used Binary, number of samples (both 0x00 and 0x01 = 1) Table 65. ALM_SMPL2 (Base Address = 0x4A), Read/Write Bits [15:8] [7:0] Description (Default = 0x0000) Alarm 2 data source selection 0000 = disable 0001 = SUPPLY_OUT 0010 = XGYRO_OUT 0011 = YGYRO_OUT 0100 = ZGYRO_OUT 0101 = XACCL_OUT 0110 = YACCL_OUT 0111 = ZACCL_OUT 1001 =XMAGN_OUT 1010 = YMAGN_OUT 1011 = ZMAGN_OUT 1100 = AUX_ADC Alarm 1 data source selection (same as Alarm 2) Alarm 2, dynamic/static (1 = dynamic, 0 = static) Alarm 1, dynamic/static (1 = dynamic, 0 = static) Not used Data source filtering (1 = filtered, 0 = unfiltered) Not used Alarm indicator (1 = enabled, 0 = disabled) Alarm indicator active polarity (1 = high, 0 = low) Alarm output line select (1 = DIO2, 0 = DIO1) Description (Default = 0x0000) Not used Binary, number of samples (both 0x00 and 0x01 = 1) 0xC703, 0xC6E8 0xC500, 0xC4D2 0xC866 Rev. A | Page 22 of 24 Description ALM_CTRL = 0x4797 Alarm 2: dynamic, Δ-ZGYRO_OUT (Δ-time, ALM_SMPL2) > ALM_MAG2 Alarm 1: static, ZACCL_OUT < ALM_MAG1, filtered data DIO2 output indicator, positive polarity ALM_MAG2 = 0x03E8 = 1,000 LSB = 50°/sec ALM_MAG1 = 0x00D2 = 210 LSB = +0.7 g ALM_SMPL2[7:0] = 0x52 = 82 samples 82 samples ÷ 819.2 SPS = ~100 ms ADIS16407 APPLICATIONS INFORMATION INSTALLATION/HANDLING INTERFACE PRINTED CIRCUIT BOARD (PCB) For ADIS16407 installation, use the following two step process: The ADIS16407/PCBZ includes one ADIS16407BMLZ and one interface PCB. The interface PCB simplifies the process of integrating these products into an existing processor system. For removal 1. 2. Gently pry the connector from its mate using a small slot screwdriver. Remove the screws and lift up the device. Never attempt to unplug the connector by pulling on the plastic case or base plate. Although the flexible connector is very reliable in normal operation, it can break when subjected to unreasonable handling. When broken, the flexible connector cannot be repaired. The AN-1045 Application Note, iSensor® IMU Mounting Tips, provides more information about developing an appropriate mechanical interface design. J1 and J2 are dual row, 2 mm (pitch) connectors that work with a number of ribbon cable systems, including 3M Part 1522120100-GB (ribbon crimp connector) and 3M Part 3625/12 (ribbon cable). Figure 23 provides a hole pattern design for installing the ADIS16407BMLZ and the interface PCB onto the same surface. Figure 24 provides the pin assignments for each connector, which match the pin descriptions for the ADIS16407BMLZ. The ADIS16407does not require any external capacitors for normal operation; therefore, the interface PCB does not use the C1/C2 pads (not shown in Figure 23). 23.75 GYROSCOPE BIAS OPTIMIZATION J2 1 The factory calibration corrects for initial and temperature dependent bias errors in the gyroscopes. Use the autonull command (GLOB_CMD[0]) and decimation filter (SMPL_PRD[12:8]) to address rate random walk (RRW) behaviors. Control physical, power supply, and temperature stability during the averaging times to help ensure optimal accuracy during this process. Refer to the AN-1041 Application Note, iSensor® IMU Quick Start Guide and Bias Optimization Tips, for more information about optimizing performance. 2 11 30.10 21.24 12 J1 1 27.70 2 1.20 11 12 09797-023 Secure the base plate using machine screws. Press the connector into its mate. NOTES 1. DIMENSIONS IN MILLIMETERS. Figure 23. Physical Diagram for the ADIS16407/PCBZ J1 J2 RST 1 2 SCLK AUX_ADC 1 2 GND CS 3 4 DOUT AUX_DAC 3 4 DIO3 DNC 5 6 DIN GND 5 6 DIO4 GND 7 8 GND DNC 7 8 DNC GND 9 10 VCC DNC 9 10 DNC VCC 11 12 VCC DIO2 11 12 DIO1 Figure 24. J1/J2 Pin Assignments Rev. A | Page 23 of 24 09797-024 1. 2. ADIS16407 OUTLINE DIMENSIONS 31.900 31.700 31.500 23.454 23.200 22.946 9.464 9.210 8.956 (2×) 2.382 BSC TOP VIEW 10.60 BSC 22.964 22.710 22.456 10.50 BSC 21.410 21.210 21.010 5.20 5.00 4.80 (2×) 14.950 14.550 14.150 PIN 24 BOTTOM VIEW 17.41 17.21 17.01 (2×) 1.588 BSC 1.588 BSC 4.20 4.00 3.80 (2×) 1.00 BSC 0.05 BSC PIN 1 7.18 BSC CASTING FEATURE 2.00 BSC 12.10 BSC FRONT VIEW 23.504 23.250 22.996 2.660 2.500 2.340 SIDE VIEW 0.305 BSC (24×) 4.330 BSC DETAIL A 4.162 BSC 1.00 BSC (22×) 1.65 BSC 14.00 BSC 122208-C DETAIL A Figure 25. 24-Lead Module with Connector Interface (ML-24-2) Dimensions shown in millimeters ORDERING GUIDE Model 1 ADIS16407BMLZ ADIS16407/PCBZ 1 Temperature Range −40°C to +105°C Package Description 24-Lead Module with Connector Interface Interface PCB Z = RoHS Compliant Part. ©2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09797-0-6/11(A) Rev. A | Page 24 of 24 Package Option ML-24-2