Radial Lead Resettable Polymer PTCs JK250 Series Description JK250 Series is designed to protect against short duration high voltage fault currents (power cross or power induction surge) typically used in AC220V. Features u u u u 0.02-2.0A hold current rating 250VAC operating voltage Fast time-to- trip RoHS compliant, Lead-Free and Halogen-Free Applicable u u u AC220V over-current protection Power ports Customer Premises Equipment(CPE) Electrical Parameters Maximum Time To Trip Current Time (A) (Sec.) V max (Vac) I max (A) P dtyp. (W) 0.045 250 3.0 1.0 1.0 0.030 0.065 250 3.0 1.0 JK250-040U 0.040 0.080 250 3.0 JK250-060U 0.060 0.120 250 JK250-080U 0.080 0.160 JK250-090U 0.090 JK250-100U Part Number I hold (A) JK250-020U 0.020 JK250-030U I trip (A) Resistance R min (Ω) R max (Ω) R 1max (Ω) 0.10 80.0 160.0 240.0 1.0 0.10 60.0 120.0 180.0 1.0 0.5 1.00 30.0 60.0 80.0 3.0 1.0 0.5 2.00 22.0 40.0 60.0 250 3.0 1.0 1.0 0.25 14.0 22.0 33.0 0.180 250 3.0 1.0 1.0 0.50 10.0 20.0 31.0 0.100 0.200 250 3.0 1.0 1.0 1.00 10.0 20.0 31.0 JK250-110U 0.110 0.220 250 3.0 1.0 1.0 1.20 6.0 12.0 16.0 JK250-120U 0.120 0.240 250 3.0 1.0 1.0 1.20 6.0 11.0 16.0 JK250-145U 0.145 0.290 250 3.0 1.0 1.0 4.00 3.5 6.5 14.0 JK250-180T 0.180 0.540 250 10.0 1.8 3.0 1.50 1.0 2.2 4.0 JK250-180U 0.180 0.540 250 10.0 1.8 3.0 1.50 1.0 3.0 5.0 JK250-200U 0.200 0.400 250 10.0 2.4 3.0 5.00 3.0 6.0 9.0 JK250-400U 0.400 0.800 250 10.0 2.8 3.0 8.0 1.0 3.0 6.0 JK250-600U 0.600 1.200 250 10.0 3.2 3.0 12.0 0.6 2.00 5.0 JK250-800U 0.800 1.600 250 10.0 3.6 4.0 18.0 0.40 1.00 3.0 JK250-1000U 1.000 2.000 250 10.0 3.6 5.0 20.0 0.50 0.80 2.0 JK250-1200U 1.200 2.400 250 10.0 3.6 6.0 20.0 0.20 0.80 2.0 JK250-1500U 1.500 3.000 250 10.0 4.8 7.5 20.0 0.20 0.60 1.5 JK250-2000U 2.000 4.000 250 10.0 4.8 10.0 20.0 0.20 0.40 1.5 UN Semiconductor Co., Ltd. Revision October 18, 2013 www.unsemi.com.tw 1/4 @ UN Semiconductor Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. Radial Lead Resettable Polymer PTCs JK250 Series I hold= Hold current: maximum current device will pass without tripping in 25°C still air. I trip= Trip current: minimum current at which the device will trip in 25°C still air. V max= Maximum voltage device can withstand without damage at rated current (Imax) I max= Maximum fault current device can withstand without damage at rated voltage (Vmax) Pdtyp.= Power dissipated from device when in the tripped state at 25°C still air. R min= Minimum resistance of device in initial (un-soldered) state. R max= Maximum resistance of device in initial (un-soldered) state. R 1max= Maximum resistance of device at 25°C measured one hour after tripping. Caution: Operation beyond the specified rating may result in damage and possible arcing and flame. 0.48 0.25 Temperature Rerating Chart – I hold (A) Ambient Operation Temperature Part Number -40°C -20°C 0°C 25°C JK250-020U JK250-030U JK250-040U JK250-060U JK250-080U JK250-090U JK250-100U JK250-110U JK250-120U JK250-145U JK250-180T JK250-180U JK250-200U JK250-400U JK250-600U JK250-800U JK250-1000U JK250-1200U JK250-1500U JK250-2000U 0.031 0.047 0.062 0.093 0.124 0.140 0.155 0.171 0.186 0.230 0.280 0.280 0.310 0.620 0.930 1.240 1.550 1.860 2.330 3.100 0.027 0.041 0.055 0.082 0.110 0.119 0.137 0.145 0.164 0.191 0.238 0.238 0.274 0.550 0.820 1.100 1.370 1.650 2.100 2.740 0.024 0.036 0.048 0.070 0.095 0.105 0.119 0.129 0.143 0.170 0.211 0.211 0.238 0.480 0.710 0.950 1.190 1.430 1.650 2.380 0.020 0.030 0.040 0.060 0.080 0.090 0.100 0.110 0.120 0.145 0.180 0.180 0.200 0.400 0.600 0.800 1.000 1.200 1.500 2.000 40°C 50°C 60°C 70°C 85°C 0.015 0.022 0.029 0.044 0.058 0.069 0.077 0.085 0.088 0.112 0.139 0.139 0.146 0.290 0.440 0.580 0.730 0.900 1.130 1.460 0.013 0.019 0.026 0.038 0.051 0.061 0.068 0.075 0.077 0.099 0.122 0.122 0.128 0.260 0.380 0.510 0.640 0.816 1.020 1.280 0.011 0.017 0.022 0.033 0.044 0.055 0.61 0.067 0.066 0.088 0.110 0.110 0.110 0.22 0.33 0.44 0.55 0.732 0.915 1.10 0.008 0.012 0.016 0.025 0.033 0.043 0.045 0.053 0.049 0.070 0.086 0.086 0.082 0.160 0.250 0.330 0.410 0.564 0.705 0.820 Hold Current (A) 0.016 0.025 0.033 0.049 0.066 0.077 0.085 0.094 0.098 0.123 0.153 0.153 0.164 0.330 0.490 0.660 0.820 1.020 1.280 1.640 Temperature Rerating Curve Time in Seconds Percentage of Rated Current Average Time Current Curves Temperature (°C) Current in Amperes Test Procedures and Requirement UN Semiconductor Co., Ltd. Revision October 18, 2013 www.unsemi.com.tw 2/4 @ UN Semiconductor Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. Radial Lead Resettable Polymer PTCs JK250 Series Test Test Conditions Accept/Reject Criteria Resistance In still air @25±2°C Rmin≤R≤Rmax Hold Current 60 min, at Ihold, In still air @25±2°C No trip Time to Trip Specified current, Vmax, @25±2°C T≤Maximum Time To Trip Trip Cycle Life Vmax, Imax,100 cycles No arcing or burning Trip Endurance Vmax,24hours No arcing or burning Soldering Parameters Pre-Heating Zone Refer to the condition recommended by the manufacturer. Max. ramping rate should not exceed 4°C/Sec Soldering Zone Max. solder temperature should not exceed 260°C Cooling Zone Cooling by natural convection in air Physical Specifications Lead Material Soldering Characteristics Insulating Material Device Labeling 0.02-0.04A Tin-plated Copper clad steel 0.05-2.00A Tin-plated Copper Solder ability per MIL-STD-202, Method 208E Cured, flame retardant epoxy polymer meets UL 94V-0 requirements. Marked with ‘SC’, voltage, current rating Dimensions Figure1 Part Number Figure Figure2 Figure3 Figure4 A B C D Lead (dia) mm Max. mm Max. mm Typ. mm Max. Inches mm (Bulk Pack) Packaging JK250-020U Figure1(2) 7.4 12.7 5.1 3.8 0.020 0.5 1000 JK250-030U Figure1(2) 7.4 12.7 5.1 3.8 0.020 0.5 1000 JK250-040U Figure1(2) 7.4 12.7 5.1 3.8 0.020 0.5 1000 JK250-060U Figure1(2) 7.4 12.7 5.1 3.8 0.024 0.6 1000 UN Semiconductor Co., Ltd. Revision October 18, 2013 www.unsemi.com.tw 3/4 @ UN Semiconductor Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. Radial Lead Resettable Polymer PTCs JK250 Series JK250-080U Figure1 7.4 12.7 5.1 3.8 0.024 0.6 1000 JK250-090U Figure1 7.4 12.7 5.1 3.8 0.024 0.6 1000 JK250-100U Figure1 7.8 12.0 5.1 3.8 0.024 0.6 1000 JK250-110U Figure3 7.0 12.6 5.1 3.8 0.024 0.6 1000 JK250-120U Figure3 7.0 10.0 5.1 3.8 0.024 0.6 1000 JK250-145U Figure3 7.0 10.0 5.1 3.8 0.024 0.6 1000 JK250-180T Figure1 10.2 14.5 5.1 3.4 0.024 0.6 1000 JK250-180U Figure3 11.2 14.5 5.1 3.8 0.024 0.6 1000 JK250-200U Figure4 10.5 17.0 5.1 3.8 0.024 0.6 1000 JK250-400U Figure4 10.5 17.0 5.1 3.8 0.031 0.8 1000 JK250-600U Figure4 16.0 18.0 5.1 4.5 0.031 0.8 500 JK250-800U Figure4 20.0 22.0 5.1 4.5 0.031 0.8 500 JK250-1000U Figure4 20.0 22.0 5.1 4.5 0.031 0.8 200 JK250-1200U Figure4 22.0 28.0 5.1 4.5 0.031 0.8 200 JK250-1500U Figure4 25.0 30.0 5.1 4.5 0.031 0.8 200 JK250-2000U Figure4 26.0 32.0 5.1 4.5 0.031 0.8 200 Warning u This product should not be used in an application where the maximum interrupt voltage or maximum interrupt current in a fault condition, Operation beyond the maximum rating or improper use may result in device damage and possible electrical arcing and flame. u A PPTC device is not a fuse, It is a nonlinear thermistor that limits current, Because under a fault condition all PPTC devices go into a high resistance state but not open circuit hazardous voltage may be present at PPTC. u The devices are intended for protection against occasional over-current or over-temperature fault conditions and should not be used when repeated fault conditions or prolonged trip events. u In most application, power must be removed and the fault condition cleared in order to reset a PPTC device. u PPTC devices are not recommended to be installed in applications where the device is constrained such that its PPTC properties are inhibited, for example in rigid potting materials or Add devices surface coating, Bundled devices ontology, which lack adequate clearance to accommodate device expansion. u Contamination on of the PPTC material with certain silicone-based oils or some aggressive solvents can adversely impact the performance of the devices. For example, Organic solvents to cleaning. UN Semiconductor Co., Ltd. Revision October 18, 2013 www.unsemi.com.tw 4/4 @ UN Semiconductor Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.