LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only LOW CURRENT DURL COLOR LED LAMPS Pb Lead-Free Parts LSEFUG3393/T-PF DATA SHEET DOC. NO : QW0905-LSEFUG3393/T-PF REV. : A DATE : 17 - Jun. - 2006 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 1/6 PART NO. LSEFUG3393/T-PF Package Dimensions 5.9 5.0 7.6 8.6 10.5±0.5 1.5 MAX UG □0.5 TYP + 1 18.0MIN 1 2 SEF 3 2.0MIN 2.54TYP Note : 1.All dimension are in millimeter tolerance is ±0.25mm unless otherwise noted. 2.Specifications are subject to change without notice. Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% + 3 1.ANODE GREEN 2.COMMON CATHODE 3.ANODE ORANGE 2.0MIN 2.54TYP 2 0 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 2/6 PART NO. LSEFUG3393/T-PF Absolute Maximum Ratings at Ta=25 ℃ Ratings Symbol Parameter UNIT SEF UG Forward Current IF 50 30 mA Peak Forward Current Duty 1/10@10KHz IFP 90 120 mA Power Dissipation PD 120 100 mW Ir 10 10 μA Reverse Current @5V Electrostatic Discharge( * ) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +100 ℃ Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic * glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Typical Electrical & Optical Characteristics (Ta=25 ℃) PART NO COLOR MATERIAL Emitted AlGaInP Orange AlGaInP Green Dominant Spectral wave halfwidth length △λ nm λDnm Forward voltage @2mA(V) Luminous intensity @2mA(mcd) Viewing angle 2θ 1/2 (deg) Min. Max. Min. Typ. Lens 605 17 1.8 2.2 350 700 40 574 20 1.8 2.2 50 90 40 Water Clear LSEFUG3393/T-PF Note : 1.The forward voltage data did not including ± 0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 3/6 PART NO. LSEFUG3393/T-PF Typical Electro-Optical Characteristics Curve SEF CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vs. Forward Current 3.0 Relative Intensity Normalize @20mA Forward Current(mA) 1000 100 10 1.0 0.1 2.5 2.0 1.5 1.0 0.5 0.0 1.0 1.5 2.0 2.5 3.0 10 1.0 1.2 1.1 1.0 0.9 0.8 0 20 40 60 80 100 Fig.5 Relative Intensity vs. Wavelength 1.0 0.5 0.0 550 600 650 Wavelength (nm) 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 Ambient Temperature( ℃) Ambient Temperature( ℃) Relative Intensity@20mA Fig.4 Relative Intensity vs. Temperature Relative Intensity@20mA Normalize @25℃ Forward Voltage@20mA Normalize @25℃ Fig.3 Forward Voltage vs. Temperature -20 1000 Forward Current(mA) Forward Voltage(V) -40 100 700 80 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSEFUG3393/T-PF Page 4/6 Typical Electro-Optical Characteristics Curve UG CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vs. Forward Current 3.0 2.5 Relative Intensity Normalize @20mA Forward Current(mA) 1000 100 10 1.0 0.1 2.0 1.5 1.0 0.5 0.0 2.0 1.0 3.0 4.0 5.0 1.0 10 Fig.4 Relative Intensity vs. Temperature Fig.3 Forward Voltage vs. Temperature 3.0 Relative Intensity@20mA Normalize @25℃ 1.2 Forward Voltage@20mA Normalize @25℃ 1000 Forward Current(mA) Forward Voltage(V) 1.1 1.0 0.9 0.8 -40 -20 0 20 40 60 80 100 Fig.5 Relative Intensity vs. Wavelength 1.0 0.5 0.0 500 550 600 Wavelength (nm) 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 80 Ambient Temperature( ℃) Ambient Temperature( ℃) Relative Intensity@20mA 100 650 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSEFUG3393/T-PF Page 5/6 Soldering Condition(Pb-Free) 1.Iron: Soldering Iron:30W Max Temperature 350°C Max Soldering Time:3 Seconds Max(One Time) Distance:2mm Min(From solder joint to body) 2.Wave Soldering Profile Dip Soldering Preheat: 120°C Max Preheat time: 60seconds Max Ramp-up 2° C/sec(max) Ramp-Down:-5°C/sec(max) Solder Bath:260° C Max Dipping Time:3 seconds Max Distance:2mm Min(From solder joint to body) Temp(° C) 260° C3sec Max 260° 5° /sec max 120° 25° 0° 0 2° /sec max Preheat 60 Seconds Max 50 100 150 Time(sec) LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSEFUG3393/T-PF Page 6/6 Reliability Test: Test Item Test Condition Description Reference Standard Operating Life Test 1.Under Room Temperature 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) This test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of high temperature for hours. MIL-STD-883:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5 ℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of low temperature for hours. High Temperature High Humidity Test 1.Ta=65 ℃±5 ℃ 2.RH=90 %~95% 3.t=240hrs ±2hrs The purpose of this test is the resistance of the device under tropical for hours. 1.Ta=105 ℃±5℃&-40 ℃±5℃ (10min) (10min) 2.total 10 cycles The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011 Solder Resistance Test 1.T.Sol=260 ℃±5 ℃ 2.Dwell time= 10 ±1sec. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1 Solderability Test 1.T.Sol=230 ℃±5 ℃ 2.Dwell time=5 ±1sec This test intended to see soldering well performed or not. MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2 Thermal Shock Test JIS C 7021: B-12 MIL-STD-202:103B JIS C 7021: B-11