●電気的光学的特性/Electro-optical characteristics Item 電源電圧 Power supply voltage 供給電圧 Power supply voltage 通信レート トランシーバー Communications rate Transceiver 消費電流 Current drawn Power Down電流 Power-down current ●外形寸法図/Outline drawing 1 1. R R 1. 1 1.95 受光中心 Light receiving center 0.85 0.85 2.4 2.65 2.2 2.4 3.75 12 VCC - 2.4 - 3.6 V Vlogic - 1.5 - VCC V - - 2.4 - 115.2 Kbps ICC No Load - 113 155 μA - 0.01 μA 10.5 - 40 mW/sr 4.0 - 40 mW/sr Ie Ie 8･Ø0.35 R 1. 1 2.2 1.14 1.14 1 1. R 2.55 受光中心 Light receiving center 3.3 ⑩ ⑧⑦⑥⑤④③ ② ① 3.3 α=0° 500 - - mW/cm2 - - - 100 μs IF-Ie特性(α=0˚, Hight Power Mode時) IF-Ie characteristics (α=0E, Hight Power Mode) LED駆動電流(IFled)特性(Vcc=2.5V) LED driving current (IFled) characteristics(Vcc=2.5V) 60 50 40 Ie(mW/sr) 50 0 P0.95×7=6.65 30 0 100 200 10 300 2.5 3 3.5 ●電気的光学的特性/Electro-optical characteristics 放射強度 Emission strength 発光部 放射強度 Light emitting Emission strength portion ピーク発光波長 Peak emission wavelength 最小受光感度 4 4.5 5 LEDA(V) IF(Ic2+IrLED)(mA) (Ta 25℃) Symbol Conditions Min Typ VCC - 2.4 - 3.6 V Vlogic - 1.5 - VCC V - - 2.4 - 115.2 Kbps ICC No Load - 113 155 μA - 0.01 μA 10.5 - 40 mW/sr 4.0 - 40 mW/sr SD=VCC Iccsd Ie Ie No Load α=0° VCC=Anode=3V α±15° VCC=Anode=3V λp Minimum receiving sensitivity Eemin 受光部 最大受光感度 Light sensing Maximum receiving sensitivity Eemax portion レイテンシー TL Latency - Max Unit 1 875 888 900 nm 8.1 μW/cm2 α=±15° - 4.0 α=0° 500 - - mW/cm2 - - - 100 μs ●諸特性/Characteristics 推奨はんだ付けパターン 0.55 3.3 ⑨ 0.55 0.7 1.6 2.7 085 7.5 4.0 3.325 Power Down電流 Power-down current 3.75 - 20 0.6 3.325 電源電圧 Power supply voltage 供給電圧 Power supply voltage 通信レート トランシーバー Communications rate Transceiver 消費電流 Current drawn マウント中心 Mounting center 8.1 μW/cm2 α=±15° マウント中心 Mounting center 1.05 Item ●外形寸法図/Outline drawing nm ●諸特性/Characteristics 1.2 CIM-55S12RV 1 875 888 900 150 単位/Unit : mm 2.55 - Max Unit 100 0.825 ⑤SD ⑥TXD2 ⑦Vlogic ⑧VCC 3.75 α=0° VCC=Anode=3V α±15° VCC=Anode=3V λp 1.65 ①LEDA ②TXD1 ③RXD ④GND No Load reflow-soldering: ベタアース Grounded wholly 3.325 SD=VCC Iccsd The following soldering patterns are recommended for ⑧ ⑦⑥⑤ ④ ③ ②① 3.325 The following soldering patterns are recommended for IF-Ie特性(α=0˚, Hight Power Mode時) IF-Ie characteristics (α=0E, Hight Power Mode) reflow-soldering: 3.3 150 LED駆動電流(IFled)特性(Vcc=2.5V) LED driving current (IFled) characteristics(Vcc=2.5V) 60 P0.95×7=6.65±0.1 3.325 0.6 ⑥TXD2 ⑦Vlogic ⑧Vcc ⑨GND ⑩GND 50 3.325 1 マウント中心 Mounting center 0.6 100 1 ILED(mA) 50 30 20 0.6 1 単位/Unit : mm Ie(mW/sr) 40 0.8 ①ANODE ②TXD1 ③RXD ④GND ⑤SD 0.3 2.7 Typ Minimum receiving sensitivity Eemin 受光部 最大受光感度 Light sensing Maximum receiving sensitivity Eemax portion レイテンシー TL Latency P0.95×7=6.65 0.6 Min 推奨はんだ付けパターン 0.85 0.05 0.75 0.375 0.6 発光中心 Light emission center Conditions 2.65 2.75 3.75 0.325 0.8 1.145 1.145 1.5 8.0±0.2 Symbol 1.3 発光中心 Light emission center 0.85 マウント中心 Mounting center (4) 0.975 (4) 放射強度 Emission strength 発光部 放射強度 Light emitting Emission strength portion ピーク発光波長 Peak emission wavelength 最小受光感度 (Ta 25℃) ILED(mA) CIM-51S12RV 3.325 3.325 P0.85×7=6.65 0 0 100 200 IF(Ic2+IrLED)(mA) 300 10 2.5 3 3.5 4 4.5 5 LEDA(V) 135