MCC Features • • • • • FR1A omponents 21201 Itasca Street Chatsworth !"# $ % !"# For Surface Mount Applications Extremely Low Thermal Resistance Easy Pick And Place High Temp Soldering: 250°C for 10 Seconds At Terminals Superfast Recovery Times For High Efficiency THRU FR1M 1 Amp Fast Recovery Silicon Rectifier 50 to 1000 Volts Maximum Ratings • • • DO-214AA (SMBJ) (Round Lead) Operating Temperature: -50°C to +150°C Storage Temperature: -50°C to +150°C Maximum Thermal Resistance; 15 °C/W Junction To Lead MCC Device Maximum Maximum Maximum Catalog Marking Recurrent RMS DC Number Peak Reverse Voltage Blocking Voltage Voltage FR1A FR1A 50V 35V 50V FR1B FR1B 100V 70V 100V FR1D FR1D 200V 140V 200V FR1G FR1G 400V 280V 400V FR1J FR1J 600V 420V 600V FR1K FR1K 800V 560V 800V FR1M FR1M 1000V 700V 1000V H Cathode Band J A E C D B F G Electrical Characteristics @ 25°C Unless Otherwise Specified Average Forward IF(AV) 1.0A TJ = 90°C current Peak Forward Surge IFSM 30A 8.3ms, half sine Current IFM = 1.0A; Maximum 1.30V Instantaneous VF TJ = 25°C* Forward Voltage Maximum DC Reverse Current At IR 5µA TJ = 25°C Rated DC Blocking 200µA TJ = 125°C Voltage Maximum Reverse Recovery Time 150ns FR1A-G IF=0.5A, IR=1.0A, Trr 250ns Irr=0.25A FR1J 500ns FR1K-M Typical Junction CJ 12pF Measured at Capacitance 1.0MHz, VR=4.0V *Pulse test: Pulse width 200 µsec, Duty cycle 2% DIMENSIONS DIM A B C D E F G H J INCHES MIN .078 .075 .002 ----.035 .065 .205 .160 .130 MM MIN 1.98 1.90 .05 ----.90 1.65 5.21 4.06 3.30 MAX .116 .089 .008 .02 .055 .091 .224 .180 .155 MAX 2.95 2.25 .20 .51 1.40 2.32 5.69 4.57 3.94 SUGGESTED SOLDER PAD LAYOUT 0.090" 0.085” www.mccsemi.com 0.070” NOTE MCC FR1A thru FR1M Figure 1 Typical Forward Characteristics 20 Figure 2 Forward Derating Curve 10 2.4 6 2.2 4 2.0 1.8 2 1.6 25°C Amps 1.4 1 1.2 .6 Amps .4 1.0 .8 .6 .2 .4 Single Phase, Half Wave .2 60Hz Resistive or Inductive Load .1 .06 0 .04 0 25 50 75 100 125 150 °C Average Forward Rectified Current - Amperesversus Ambient Temperature - °C .02 .01 .8 .6 10 1.2 1.4 1.6 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF TJ=25°C 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 Junction Capacitance - pFversus Reverse Voltage - Volts www.mccsemi.com 400 1000 MCC FR1A thru FR1M Figure 4 Peak Forward Surge Current 36 Figure 5 New SMB Assembly 30 24 18 Amps 12 Round Lead Process 6 0 1 2 4 6 8 10 20 40 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 Pulse Generator Note 2 25Vdc 1Ω Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm www.mccsemi.com