CHENMKO ENTERPRISE CO.,LTD CHDTA123EUPT SURFACE MOUNT PNP Digital Silicon Transistor VOLTAGE 50 Volts CURRENT 100 mAmpere APPLICATION * Switching circuit, Inverter, Interface circuit, Driver circuit. FEATURE SC-70/SOT-323 * Small surface mounting type. (SC-70/SOT323) * High current gain. * Suitable for high packing density. (2) Low colloector-emitter saturation. High saturation current capability. Internal isolated PNP transistors in one package. Built in bias resistor(R1=2.2kΩ, Typ. ) (3) 1.3±0.1 (1) * * * * 0.65 2.0±0.2 0.65 0.3±0.1 CONSTRUCTION 1.25±0.1 * One PNP transistors and bias of thin-film resistors in one package. MARKING EU1 0.8~1.1 0.05~0.2 0~0.1 0.1Min. CIRCUIT Gnd In 2 1 2.0~2.45 R2 TR R1 SC-70/SOT-323 3 Out Dimensions in millimeters LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC Supply voltage − -50 V VIN Input voltage -12 +10 V − -100 − -100 − 200 mW O C IO DC Output current IC(Max.) Tamb ≤ 25 OC, Note 1 mA PTOT Total power dissipation TSTG Storage temperature −55 +150 TJ Junction temperature − 150 O C Thermal resistance − 140 O C/W RθJ-S junction - soldering point Note 1. Transistor mounted on an FR4 printed-circuit board. 2005-06 RATING CHARACTERISTIC ( CHDTA123EUPT ) CHARACTERISTICS Tamb = 25 °C unless otherwise speciÞed. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT VIoff) Input off voltage IO=-100uA; VCC=-5.0V -0.5 − − V VI(on) Input on voltage IO=-20mA; VO=-0.3V − − -3.0 V VO(on) Output voltage IO=-10mA; II=-0.5mA − - 0.1 - 0.3 V II Input current VI=-5V − − -3.8 mA IC(off) Output current VI=0V; VCC=-50V − − -0.5 uA hFE DC current gain IO=-20mA; VO=-5.0V 20 − − R1 Input resistor 1.54 2.2 2.86 KΩ R2/R1 fT Resistor ratio Transition frequency 0.8 − 1.0 250 1.2 − MHz Note 1.Pulse test: tp≤300uS; δ≤0.02. IC=-5mA, VCE=-10.0V f=100MHz = RATING CHARACTERISTIC CURVES ( CHDTA123EUPT ) Typical Electrical Characteristics Fig.1 Input voltage vs. output current (ON characteristics) 20 10 5 10m 5m VO=−0.3V 50 OUTPUT CURRENT : Io (A) INPUT VOLTAGE : VI(on) (V) 100 Fig.2 Output current vs. input voltage (OFF characteristics) Ta=−40°C 25°C 100°C 1 500m 200m 100m −100µ −200µ −500µ −1m −2m −5m −10m −20m 2m 1m 500µ 100µ 50µ 20µ 10µ 5µ Fig.3 DC current gain vs. output current VO=−5V 200 100 50 20 Ta=100°C 25°C −40°C 10 5 2 1 −100µ −200µ −500µ −1m −2m −5m −10m −20m OUTPUT CURRENT : IO −50m −100m −0.5 −1.0 −1.5 −2.0 −2.5 −3.0 Fig.4 Output voltage vs. output current 1 OUTPUT VOLTAGE : VO(on) (V) DC CURRENT GAIN : GI 1k 0 INPUT VOLTAGE : VI(off) (V) OUTPUT CURRENT : IO (A) 500 Ta=100°C 25°C −40°C 200µ 2µ 1µ −50m −100m VCC=−5V IO/II=20 500m 200m 100m Ta=100°C 50m 25°C −40°C 20m 10m 5m 2m 1m −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m −100m OUTPUT CURRENT : IO (A)