I/O Card Interface Connectors NX Series 3. ESD Secure Thermoplastic molded covers assures insulation of the connections and shields from ESD. 4. Secure Latching A built-in latch assures correct and secure mating of connector. 5. Reliable Conductor Termination Reliable termination of conductors accomplished by proven IDC termination. is 6. Sequential Mating The 0.8mm pitch contacts are engaging the corresponding parts in sequence: GroundPower & Signal 7. Rugged Construction Securely attached to the board with optional screws. ■Features 1. Low Profile Protorusion above the PCB board is only 2.9mm, and the connectors can be mounted to type I and II I/O cards. 2. EMI/RFI protection Full metal shielding. Shield connects first, ahead of contacts. 8. Card Frame Kits Available as a separate part number. 9. Secure Attachment to Frame Kit. Compliant mounting bracket attaches the connectore directly to the frame kit. ■Applications Used with I/O cards, portable personal computers,and the external connections of various small-sized portable terminals. ■Specifications Current rating 0.5 A Ratings Voltage rating 125 V AC Item Operating temperature -30ç to +70ç (Note 1) Storage temperature range -10ç to +60ç (Note 2) Operating humidity 95% R.H. or less (No condensation) Storage humidity range Specification 40 to 70% (Note 2) Conditions 1. Insulation resistance 250 M ohms min. 100 V DC 2. Withstanding voltage No flashover or insulation breakdown. 300 V AC / 1 minute 3. Contact resistance 40 m ohms max. 100 mA 4. Vibration No electrical discontinuity of 10µs or more Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 5. Humidity (Steady state) Insulation resistance: 100 M ohms min. 96 hours at temperature of 60ç and humidity of 90% to 95% 6. Temperature cycle No damage, cracks, or parts looseness. -55ç, 30 min./15 to 30ç, within 5 min/85ç, 30 min /15 to 35ç, within 5 min, for 5 cycles 7. Durability (Insertion/withdrawal) 60 m ohms max. 3000 cycles 8. Resistance to Soldering heat No deformation of components affecting Reflow: At the recommended temperature profile performance. Manual soldering: 300ç for 3 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation. B8 ■Materials BApplicable Cable Item Material Insulator Receptacle Contacts Plug unit Plug cover Finish Thermoplastic Compound Black UL94V-0 Copper alloy Selective gold plating ---- Body Stain less Solder Plating ---- Insulator Thermoplastic Compound Black ---- Contacts Copper alloy Selective gold plating UL94V-0 Cover Thermoplastic Compound Black Body Stainless Steel Frame Thermoplastic Compound I/O cable AWG # 28(7/0.127) Conductor size Jacket outer diameter 0.58mm 0.62mm Cable style UL20276 and UL2789 UL2990 ---UL94V-0 - Frame ground Phosphor bronze terminal Frame kit Remarks Black ---- Gold Plating ---- Spring pin Stainless steel - ---- Coil spring Stainless steel - ---- Panel Stainless steel With thermal adhesive tape ■Ordering Information ---- Serise name : NX Termination style ●Receptacle 30 : IDC termination (for fine wire) NX 60 T A - 15 S AA 9 - SP 1 2 3 5 11 6 7 8 9 60 : SMT type Lock T : Inner lock ●Plug Applicable Conductor NX 30 T A - 15 P AA 1 2 3 4 5 6 7 Number of contacts : 9, 15, 25, 32 Connector type P : Plug ●Plug Covers S : Receptacle Polarizing AA : AA type NX - 15 T A - CV 1 A : AWG #28 5 3 11 Offset 10 9 : 0.9 mm 3 : 0.3 mm None : On Board Type (Dimension from connector center line to the surface of the PCB) ●Frame Kits Variations NX - 15 T - KT 9 (05) 1 5 3 10 8 12 SP : Compliant mounting bracket(for cards use) SH : Through hole Types of accessories CV : Vertical opening cover case ●Panel (For 9, 15, or 25 contacts) KT : Frame kit NX T - P (05) 1 3 10 K : Frame 12 P : Panel (For Type2card) PA : Panel (For Type1card) (For 32 contacts) BS : Bushing NX - 32 T - P (05) 1 5 CV1 : Vertical opening cover case(Thin 5 mm thinclness type) 3 10 12 CSA : Coil spring CSB : Coil spring Serial number by type Panel finish No symbol : Silver matt finish (05) : Dull Processing material B9 BDimensions of Connector Cross Section ●0.9 mm offset type ●0.3 mm offset type BRecommended Board Dimensions (Board Thickness: 0.5 mm Maximum) Unit: mm B10 Part Number CL No. Number of contacts A B C D offset NX-09T-KT9 234-0010-8 09 26.4 25.0 22.4 06.4 0.9 NX-15T-KT9 234-0011-0 15 31.2 29.8 27.2 11.2 0.9 NX-25T-KT9 234-0012-3 25 39.2 37.8 35.2 19.2 0.9 NX-32T-KT9 234-0026-8 32 44.8 43.4 40.8 24.8 0.9 NX-09T-KT3 234-0034-6 09 26.4 25.0 22.4 06.4 0.3 NX-15T-KT3 234-0035-9 15 31.2 29.8 27.2 11.2 0.3 NX-25T-KT3 234-0036-1 25 39.2 37.8 35.2 19.2 0.3 NX-32T-KT3 234-0054-3 32 44.8 43.4 40.8 24.8 0.3 ■Receptacle ●0.9 mm offset type D P=0.8 Contact No.1 2 • 2 8 1.9 0.3 A NX60TA-✽ SAA9-SP B Ø1 2.9 0.9 C Unit: mm Part Number CL No. Number of contacts A B C D NX60TA-09SAA9-SP 234-0106-5 09 25.2 19.7 17.2 06.4 NX60TB-15SAA9-SP 234-0097-6 15 30.0 24.5 22.0 11.2 NX60TA-25SAA9-SP 234-0107-8 25 38.0 32.5 30.0 19.2 NX60T0-32SAA9-SP 234-0023-0 32 43.6 38.1 35.6 24.8 ●0.3 mm offset type Contact No.1 NX60TA-✽ SAA3-SP Unit: mm Part Number CL No. Number of contacts A B C D NX60TA-09SAA3-SP 234-0031-8 09 25.2 19.7 17.2 06.4 NX60TB-15SAA3-SP 234-0098-9 15 30.0 24.5 22.0 11.2 NX60TA-25SAA3-SP 234-0033-3 25 38.0 32.5 30.0 19.2 NX60TA-32SAA3-SP 234-0053-0 32 43.6 38.1 35.6 24.8 B11 ■Plug units NX30TA-15PAA CL234-0005-8 Contact No.1 Unit: mm Part Number CL No. Number of contacts A B NX30TA-09PAA 234-0002-0 09 14.6 14.1 NX30TA-15PAA 234-0005-8 15 19.4 18.9 NX30TA-25PAA 234-0008-6 25 27.4 26.9 NX30TA-32PAA 234-0024-2 32 33.0 32.5 ■Plug Covers NX-15T-CV CL234-0006-0 Unit: mm Part Number CL No. Number of contacts A B C D E F G Outer diameter of cable NX-09T-CV 234-0003-2 09 18.2 21.2 14.0 26 06.0 5.5 6.5 less than Ø 5.5 NX-15T-CV 234-0006-0 15 23.0 26.0 18.8 28 07.0 6.0 7.0 less than Ø 6.0 NX-15T-CV1 234-0017-7 15 23.0 26.0 18.8 28 05.0 4.0 5.0 less than Ø 4.0 NX-25T-CV 234-0009-9 25 31.0 34.0 26.8 30 08.0 6.5 7.5 less than Ø 6.5 NX-25TA-CV1 234-0039-0 25 31.0 34.0 26.8 32 13.0 4.0 5.0 less than Ø 6.5(Note) NX-32TA-CV1 234-0025-5 32 36.6 40.6 32.4 32 16.2 4.2 5.0 less than Ø 7.5(Note) Note: Designed for flat cable use. when round cable is used, clamp portion shall be made flat, adjusting exclusive use bushing. B12 Frame ■Frame kit ■(Frame + 2 X Cover Panels) Cover NX-15T-KT9 CL234-0011-0 Unit: mm Connectors for the card Side(Note 1) Part Number CL No. Number of contacts NX-09T-KT9 234-0010-8 09 NX-15T-KT9 234-0011-0 15 NX-25T-KT9 234-0012-3 25 NX-32T-KT9 234-0026-8 32 NX60TA-32SAA9-SP NX-09T-KT3 234-0034-6 09 NX60TA-09SAA3-SP NX-15T-KT3 234-0035-9 15 NX-25T-KT3 234-0036-1 25 NX-32T-KT3 234-0054-3 32 CL No. Part Number Offset Back Connector NX60TA-09SAA9-SP IC1F-68RD-1.27SFA IC1F-68RD-1.27SFA 640-0040-3 640-0035-3 0.9mm 0.3mm NX60TB-15SAA9-SP NX60TA-25SAA9-SP NX60TB-15SAA3-SP NX60TA-25SAA3-SP NX60TA-32SAA3-SP ■Frame only NX-15T-F9 CL234-0019-2 Unit: mm Part Number CL No. Number of contacts Connectors for the card Side Back Connector Panel NX-09T-F9 234-0018-0 09 NX-15T-F9 234-0019-2 15 NX-25T-F9 234-0020-1 25 NX-32T-F9 234-0063-4 32 NX60TA-32SAA9-SP NX-32T-P NX-09T-F3 234-0060-6 09 NX60TA-09SAA3-SP NX-15T-F3 234-0061-9 15 NX-25T-F3 234-0062-1 25 NX-32T-F3 234-0067-5 32 Coil Spring Offset NX-CSA 0.9mm NX60TA-09SAA9-SP IC1F-68RD-1.27SFA IC1F-68RD-1.27SFA NX60TB-15SAA9-SP NXT-P NX60TA-25SAA9-SP NX60TB-15SAA3-SP NXT-P NX60TA-25SAA3-SP NX60TA-32SAA3-SP NX-32T-P NX-CSA & 0.3mm NX-CSB B13 2PCMCIA cards) ■Panel (for type2 NXT-P CL234-0058-4 Unit: mm Part Number CL No. NXT-P 234-0058-4 NXT-P(05) 234-0058-4-05 NX-32T-P 234-0059-7 NX-32T-P(05) 234-0059-7-05 Number of Frame contacts 9, 15, 25 32 Panel Finish Silver matt finish Dull processing material Silver matt finish Dull processing material 1PCMCIA cards) ■Panel (for type1 NXT-PA CL234-2011-1 Part Number CL No. NXT-PA 234-2011-1 NXT-PA(05) 234-2011-1-05 NX-32T-PA 234-0068-8 Number of Frame contacts 9, 15, 25 32 Panel Finish Silver matt finish Dull processing material Silver matt finish Dull processing material NX-32T-PA(05) 234-0068-8-05 ✽ Panels are avilable in two types: a 32-contact special type and a common type with 9, 15, or 25 contacts. ✽ Ordering volume for panels is one panel per unit volume.One frame corresponds to 2 panels. B14 ■Ground contact spring ■Bushing NX-CSA CL234-0042-4 Part Number CL No. NX-32T-BS CL234-0055-6 Offset: Ordering Volume Part Number CL No. Number of contacts NX-25T-BS 234-0074-0 25 NX-32T-BS 234-0055-6 32 NX-CSA 234-0042-4 0.3mm: One Pack 0.9mm: Two Packs NX-CSB 234-0043-7 0.3mm: One Packs Sold in package of 1000 pcs. For 1,000 frames of 0.9 offset, please order two packs of NX-CSA. For 1,000 frames of 0.3 offset, please order one pack of NX-CSA and one pack of NX-CSB. Applications for Connections of I/O Card Connectors ■Modular plugs for round cable (AWG #28) connector No. of contacts 6 Contacts Modular Plug Manual Wiring Tool Part Number CL No. Part Number CL No. 6 TM30P-66P 222-2684-2 TC1-TM30P-66P 250-0145-6 8 TM30P-88P 222-2685-5 TC1-TM30P-88P 250-0146-9 8 Contacts ■8-Contact adapter Lead Number Reference Table TM5RL-88-JJ CL222-3798-7 Connector (a) Contact number TM5RL-88 1 2 3 4 5 6 7 8 Connector (b) Contact number TM5RL-88 1 2 3 4 5 6 7 8 B15 BPlug Termination Tool ●Fixtures Cable wiring cradle NX/3230-CAT CL902-0250-4 Cutting and IDC termination Fixture main unit NX/3230-HP CL902-0252-0 Cutting and IDC termination attachment fixtures NX30TA-9GP CL902-0253-2 NX30TA-15GP CL902-0254-5 NX30TA-25GP CL902-0255-8 NX30TA-32GP CL902-0257-3 ●Wiring Procedure B16 ➀ ➁ ➂ 1. Set the wires in the wiring fixtures. 2. Align holding plates (A) and (B). 3. Arrange the wires one at a time through holding plates (A) and (B). ➅ ➄ ➃ 4. Set holding plates (A) and (B) onto the guide plate. 5. Insert the guide plate into the pressure welding and cutting fixtures. 6. Pull down the handle. The wiring and cutting of excess cable length are completed. B Frame Kit Fixture Ground spring press fitting fixture Special blocks A frame kit thermal fixture and a cooling fixture are also available. B Wiring Fixture and Accessories List Plug Process Cable I/O Cable Discrete cable Connector Wiring Pressurs Welding and Cutting Press Guide Plate Shield Case Caulking Cover Case Hand Tool Hood Fitting NX-30TA-9HC NX30TA-09PAA NX30TA-09GP NX-09T-CV0 NX30TA-32PAA NX30TA-32GP NX-32T-CV1 Screw Fixing CL902-0260-8 NX-30TA-15HC NX-15T-CV0 NX/3230-CAT CL902-0261-0 NX30TA-15GP NX30TA-15PAA NX-30TA-15HC1 Manual Work (All contacts NX/3230-HP NX-15T-CV1 CL902-0262-3 common) NX-30TA-25HC1 NX30TA-25GP NX-25T-CV NX30TA-25PAA CL902-0263-6 Note 1: The caulking height of hand tool is defined by follwing cable specifications. Note 2: Caulking specification change is needed when special cable is used. Cable Diameter Strand Termination NX-9T-CV Cover Case Ø 5.1±0.2 Fold the shield and bind 1.5 times with copper tape. NX-15T-CV Ø 5.7±0.2 Do, NX-25T-CV Ø 6.5±0.2 Do, NX-15T-CV1 Ø 3.8±0.2 Crimp with cable sheath directly. Frame Kit Process Frame Kit Spring Pin Press Fitting Panel Thermal Press Caulking NX-25T-KT(9•3) NX-32T-KT(9•3) Panel Cooling NX-SPT-9 NX-9T-KT(9•3) NX-15T-KT(9•3) Unit CL902-0275-5 NX-SPT-15 NX-SPT CL902-0276-8 NX-PHT NX-PCT CL902-0274-2 NX-SPT-25 CL902-0282-0 CL902-0283-3 CL902-0277-0 NX-SPT-32 CL902-0278-3 B17 Back Connectors for Type II I/O Cards ■NX Series 68 ■Features 1. Low profile Receptacle connectors have a mounting height of 3.5 mm and can be mounted to type II I/O cards. 2. Shielded construction A metal shell is used for shielding. 3. ESD protection The use of an over-mold cover offers excellent ESD protection. 4. More efficient wiring work Wiring on the plug side uses AWG #30 pressure welding (discrete type) for more efficient wiring work. ■Applications ■Specifications Item I/O card interfaces. Specification Conditions 1. Current rating 0.5A ---------- 2. Voltage rating 125 V AC ---------- BApplicable I/O Cable Conductor size AWG #30 (7/0.1) Insulator outer diameter 0.5mm Cable style UL20276 Finish Remarks 3. Insulation resistance 250 M ohms min. 100 V DC No flashover or insulation breakdown. 4. Withstanding voltage 300 V AC 40 m ohms min. 100 mA 5. Contact resistance 6. Durability (Insertion/withdrawal) 3000 cycles Contact resistance : 60 m ohms max. ■Materials Item Material Receptacle Plug unit Plug cover Frame kit Insulator Synthetic resin Color : Black UL94V-0 Contacts Copper alloy Selective gold plating ---------- Body Stainless steel Solder plating ---------- Insulator Synthetic resin Color : Black UL94V-0 Contacts Copper alloy Selective gold plating ---------- Cover Synthetic resin Color : Black UL94V-0 Body Stainless steel ---------- ---------- Frame Synthetic resin Color : Black UL94V-0 FG terminal Phosphor bronze Gold plating ---------- Spring pin Stainless steel ---------- ---------- Coil spring Stainless steel ---------- ---------- Panel Stainless steel With thermal adhesive tape ---------- ■Ordering Information ●Receptacle NX 60 H - 68 S 9 - SP 1 2 3 4 5 6 7 ●Plug unit NX 30 H - 68 P 1 2 3 4 3 Wiring style 30: Loose lead pressure welding type (for fine wire) 3 Serial type for form 4 Number of contacts: 68 5 Type of opening S: Receptacle 60: SMT type P: Plug NX - 68 H - CV 4 Series name:NX 2 5 ●Plug cover 1 1 8 6 Coplanarity: 0.9 (Dimension from connector center to board mounting position) 7 Variations SP: Spring pin (for cards) 8 Type of accessories CV: Vertical opening cover ●Frame kit NX - 68 H - KT 9 (05) 1 B18 4 3 8 6 9 KT: Frame kit 9 Panel finish (05): Dull processing ■Receptacle Note 1: The signal pin SMT dimension of this product is 0+0.1 -0.05. Note 2: Caulking specification change is needed when special cable is used. Part Number CL No. NX60H-68S9-SP 234-0078-1 ■Plug Unit Part Number CL No. NX30H-68P 234-0079-4 B19 ■Plug Cover Part Number CL No. NX-68H-CV 234-0080-3 ■Frame Kit Main unit Panel Note 1: Suitable connectors for portion A are IC1F-68RD-1.27SFA. Suitable connectors for portion B are NX60H-68S9-SP. B20 Part Number CL No. NX-68H-KT9(05) 234-0081-6-05 BRCB mounting pattern (Applicable Board Thickness: 0.5 mm MAX) Note 1: Applicable connectors for portion A are IC1F-68RD-1.27SFA. Applicable connectors for portion B are NX60H-68S9-SP. BConnector Mounting Dimensions B21 BTemperature Profile 10s max ● Applicable Conditions Temperature(ç) Reflow system : IR reflow 240 230 Solder : Paste type 63 Sn/37 Pb 200 Test board Glass epoxy 47mm x 77.3mm x 0.5 mm 180 Metal mask thickness: 0.15 mm (Flux content 9 wt%) 150 ● Recommended temperature profile. The temperature may be slightly changed according to the solder paste type and amount. 0 120s max Preheating Time 40s max 40s max Soldering time Time B22