NPC CF5006DKC-1 Crystal oscillator module ic Datasheet

SM5006 series
Crystal Oscillator Module ICs
OVERVIEW
The SM5006 series are crystal oscillator module ICs, that incorporate high-frequency, low current consumption oscillator and output buffer circuits. Highly accurate thin-film feedback resistors and high-frequency
capacitors are built-in, eliminating the need for external components to make a stable 3rd overtone oscillator.
FEATURES
■
■
■
■
■
■
Up to 107MHz operation
Capacitors CG, CD built-in
Inverter amplifier feedback resistor built-in
TTL input level
16mA (VDD = 4.5V) drive capability
4mA (VDD = 4.5V) drive capability (5006AH×)
■
■
■
■
■
Output three-state function
2.7 to 5.5V supply voltage
Oscillator frequency output
8-pin SOP (SM5006×××S)
Chip form (CF5006×××)
SERIES CONFIGURATION
3V operating
Version*1
gm
ratio
SM5006ANAS
SM5006ANBS
SM5006ANCS
SM5006ANDS
0.5
1
2
2
Output
load
(max)
[pF]
−
−
15
15
Recommended
operating
frequency
range*2 [MHz]
−
−
22 to 30
30 to 50
SM5006ANES
3
15
50 to 70
SM5006ANFS
4
−
−
SM5006CNCS
2
15
22 to 30
SM5006CNDS
SM5006CNES
2
3
15
15
30 to 40
50 to 70
SM5006BNCS
2
15
22 to 70
SM5006BNES
3
15
22 to 70
SM5006DNCS
2
15
22 to 40
SM5006DNES
3
15
22 to 70
SM5006AKAS
SM5006AKBS
SM5006AKCS
SM5006AKDS
SM5006CKDS
SM5006BKCS
SM5006DKCS
SM5006AHAS
SM5006AHBS
SM5006AHCS
SM5006AHDS
0.5
1
2
2
2
2
2
0.5
1
2
2
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
Built-in
capacitance
5V operating
Output
load
(max)
[pF]
50
50
50
50
30
(15)*4
30
(15)*4
15
50
15
15
15
50
30
(15)*4
15
50
15
50
15
15
15
15
15
15
15
15
15
15
15
Rf
[kΩ]
Input
level
Output
duty
level
16
16
16
16
8.2
5.6
4.9
2.6
TTL
TTL
TTL
TTL
CMOS
CMOS
CMOS
CMOS
8
16
2.6
TTL
CMOS
6/6
8
16
2.6
TTL
CMOS
Recommended
operating
frequency
range*2 [MHz]
22 to 30
30 to 40
40 to 60
50 to 70
Output
waveform*3
tr /tf [ns]
CG
[pF]
CD
[pF]
8/8
8/8
7/7
7/7
8
8
8
8
70 to 100
6/6
80 to 107
40 to 60
40 to 50
50 to 70
70 to 100
22 to 100
22 to 70
8/8
8
16
4.9
TTL
CMOS
8/8
7/7
8
8
16
16
2.6
2.6
TTL
TTL
CMOS
CMOS
7/7
8
16
No
TTL
CMOS
70 to 107
6/6
8
16
No
TTL
CMOS
8/8
8
16
No
TTL
CMOS
7/7
8
16
No
TTL
CMOS
4/4
4/4
4/4
4/4
4/4
4/4
4/4
7/7
7/7
7/7
7/7
8
8
8
8
8
8
8
8
8
8
8
16
16
16
16
16
16
16
16
16
16
16
8.2
5.6
4.9
2.6
2.6
No
No
8.2
5.6
4.9
2.6
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
CMOS
CMOS
CMOS
CMOS
22 to 70
22 to 50
22 to 100
22 to 70
22 to 30
30 to 40
40 to 60
50 to 70
50 to 70
22 to 70
22 to 70
22 to 30
30 to 40
40 to 60
50 to 70
*1. Chip form devices have designation CF5006×××.
*2. The recommended operating frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscillator frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the
oscillation characteristics of components must be carefully evaluated.
*3. 5006×N×: CL = 50pF, CMOS load, 5006×K×: CL = 15pF, 10TTL load, 5006AH×: CL = 15pF, CMOS load
*4. SOP package only
SEIKO NPC CORPORATION —1
SM5006 series
ORDERING INFORMATION
Device
Package
SM5006×××S
8-pin SOP
CF5006×××–1
Chip form
PACKAGE DIMENSIONS
(Unit: mm)
• 8-pin SOP
0.4 0.2
6.2 0.3
4.4 0.2
0.15 + 0.1
− 0.05
0.695typ
1.5
0.1
0.05 0.05
5.2 0.3
1.27
0 to 10
0.10
0.4 0.1
0.12 M
SEIKO NPC CORPORATION —2
SM5006 series
PAD LAYOUT
PINOUT
(Unit: µm)
(Top view)
VDD
Q
(920,1310)
HA5006
Y
(0,0) INHN XT XTN VSS
INHN
1
8
VDD
XT
2
7
NC
XTN
3
6
NC
VSS
4
5
Q
X
Chip size: 0.92 × 1.31mm
Chip thickness: 300 ± 30µm
Chip base: VDD level
PIN DESCRIPTION and PAD DIMENSIONS
Pad dimensions [µm]
Number
Name
I/O
Description
1
INHN
I
Output state control input. High impedance when LOW. Pull-up resistor built in
X
Y
195
212
2
XT
I
Amplifier input.
3
XTN
O
Amplifier output.
4
VSS
–
Ground
766
212
5
Q
O
Output. Output frequency (fO)
765
1152
6
NC
–
No connection
–
–
7
NC
–
No connection
–
–
8
VDD
–
Supply voltage
162
1152
Crystal oscillator connection pins.
Crystal oscillator connected between XT and XTN
385
212
575
212
BLOCK DIAGRAM
VDD VSS
XTN
RG
CG
XT
RD
Rf
CD
Q
INHN
SEIKO NPC CORPORATION —3
SM5006 series
SPECIFICATIONS
Absolute Maximum Ratings
VSS = 0V
Parameter
Symbol
Condition
Rating
Unit
Supply voltage range
VDD
−0.5 to 7.0
V
Input voltage range
VIN
−0.5 to VDD + 0.5
V
Output voltage range
VOUT
−0.5 to VDD + 0.5
V
Operating temperature range
Topr
−40 to 85
°C
Storage temperature range
Tstg
Output current
Power dissipation
IOUT
PD
Chip form
−65 to 150
8-pin SOP
−55 to 125
5006×N×, ×K×
25
5006AH×
10
8-pin SOP
500
°C
mA
mW
SEIKO NPC CORPORATION —4
SM5006 series
Recommended Operating Conditions
SM5006 series (package form)
VSS = 0V
Rating
Parameter
Symbol
Series
typ
max
f ≤ 50MHz, CL = 50pF
4.5
–
5.5
f ≤ 70MHz, CL = 15pF
4.5
–
5.5
f ≤ 40MHz, CL = 15pF
2.7
–
3.6
f ≤ 70MHz, CL = 50pF
4.5
–
5.5
f ≤ 100MHz, CL = 15pF
4.5
–
5.5
f ≤ 50MHz, CL = 15pF
2.7
–
3.6
f ≤ 70MHz, CL = 15pF
3.0
–
3.6
f ≤ 100MHz, CL = 15pF
4.5
–
5.5
f ≤ 107MHz, CL = 15pF
4.5
–
5.5
f ≤ 50MHz, CL = 15pF
2.7
–
3.6
f ≤ 70MHz, CL = 15pF
3.0
–
3.6
AKA, AKB, AKC,
CKD, DKC
f ≤ 70MHz, CL = 15pF
4.5
–
5.5
V
AKD, BKC
f ≤ 70MHz, CL = 15pF
4.5
–
5.5
V
AHA, AHB, AHC,
AHD
f ≤ 70MHz, CL = 15pF
4.5
–
5.5
V
VSS
–
VDD
V
f ≤ 50MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
0
–
+ 70
f ≤ 40MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6
− 10
–
+ 70
f ≤ 50MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 80
f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5
− 20
–
+ 80
f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 100MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
0
–
+ 70
f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6
− 20
–
+ 80
f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6
− 20
–
+ 80
f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5
− 20
–
+ 80
f ≤ 100MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 107MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 20
–
+ 80
f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6
− 20
–
+ 80
f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6
− 20
–
+ 80
f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
0
–
+ 70
f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 20
–
+ 80
f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 15
–
+ 75
ANC, AND, BNC,
CNE, DNE
VDD
ANE, ANF, BNE
Input voltage
VIN
All series
ANA, ANB, CNC,
CND, DNC
ANC, AND, BNC,
CNE, DNE
Operating temperature
Unit
min
ANA, ANB, CNC,
CND, DNC
Supply voltage
Condition
TOPR
ANE, ANF, BNE
AKA, AKB, AKC,
CKD, DKC
AKD, BKC
AHA, AHB, AHC,
AHD
V
V
V
°C
°C
°C
°C
°C
°C
SEIKO NPC CORPORATION —5
SM5006 series
CF5006 series (chip form)
VSS = 0V
Rating
Parameter
Symbol
Series
typ
max
f ≤ 50MHz, CL = 50pF
4.5
–
5.5
f ≤ 70MHz, CL = 15pF
4.5
–
5.5
f ≤ 40MHz, CL = 15pF
2.7
–
3.6
f ≤ 70MHz, CL = 50pF
4.5
–
5.5
f ≤ 100MHz, CL = 15pF
4.5
–
5.5
f ≤ 50MHz, CL = 15pF
2.7
–
3.6
f ≤ 70MHz, CL = 15pF
3.0
–
3.6
f ≤ 70MHz, CL = 50pF
4.5
–
5.5
f ≤ 107MHz, CL = 30pF
4.5
–
5.5
f ≤ 50MHz, CL = 15pF
2.7
–
3.6
f ≤ 70MHz, CL = 15pF
3.0
–
3.6
AKA, AKB, AKC,
CKD, DKC
f ≤ 70MHz, CL = 15pF
4.5
–
5.5
V
AKD, BKC
f ≤ 70MHz, CL = 15pF
4.5
–
5.5
V
AHA, AHB, AHC,
AHD
f ≤ 70MHz, CL = 15pF
4.5
–
5.5
V
VSS
–
VDD
V
f ≤ 50MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 15
–
+ 75
f ≤ 40MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6
− 10
–
+ 70
f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 100MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 20
–
+ 80
f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6
− 20
–
+ 80
f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6
− 20
–
+ 80
f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 100MHz, CL = 30pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 107MHz, CL = 30pF, 4.5 ≤ VDD ≤ 5.5
− 20
–
+ 80
f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6
− 20
–
+ 80
f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6
− 20
–
+ 80
f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 15
–
+ 75
f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 20
–
+ 80
f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 40
–
+ 85
f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5
− 20
–
+ 80
ANC, AND, BNC,
CNE, DNE
VDD
ANE, ANF, BNE
Input voltage
VIN
All series
ANA, ANB, CNC,
CND, DNC
ANC, AND, BNC,
CNE, DNE
Operating temperature
TOPR
Unit
min
ANA, ANB, CNC,
CND, DNC
Supply voltage
Condition
ANE, ANF, BNE
AKA, AKB, AKC,
CKD, DKC
AKD, BKC
AHA, AHB, AHC,
AHD
V
V
V
°C
°C
°C
°C
°C
°C
SEIKO NPC CORPORATION —6
SM5006 series
Electrical Characteristics
5006×N series
3V operation: VDD = 2.7 to 3.6 V, VSS = 0 V, Ta = −20 to 80 °C unless otherwise noted.
Rating
Parameter
Symbol
Condition
Unit
min
typ
max
HIGH-level output voltage
VOH
Q: Measurement cct 1, VDD = 2.7V, IOH = 8mA
2.2
2.4
–
V
LOW-level output voltage
VOL
Q: Measurement cct 2, VDD = 2.7V, IOL = 8mA
–
0.3
0.4
V
VOH = VDD
–
–
10
VOL = VSS
–
–
10
IZ
Q: Measurement cct 2, INHN = LOW,
VDD = 5.5V
HIGH-level input voltage
VIH
INHN
2.0
–
–
V
LOW-level input voltage
VIL
INHN
–
–
0.5
V
Output leakage current
Current consumption
INHN pull-up resistance
Feedback resistance
Built-in resistance
Built-in capacitance
IDD
RUP
Rf
INHN = open,
Measurement cct 3,
load cct 1,
VDD = 3.0 to 3.6V,
CL = 15pF
f = 30MHz
SM5006ANCS
CF5006ANC
SM5006BNCS
CF5006BNC
–
8
16
f = 30MHz,
Ta = –10 to 70°C
SM5006CNCS
CF5006CNC
–
8
16
f = 50MHz
SM5006ANDS
CF5006AND
–
13
26
f = 70MHz
SM5006BNES
CF5006BNE
SM5006CNES
CF5006CNE
SM5006DNES
CF5006DNE
–
15
30
f = 40MHz,
Ta = –10 to 70°C
SM5006CNDS
CF5006CND
SM5006DNCS
CF5006DNC
–
11
22
f = 70MHz
SM5006ANES
CF5006ANE
SM5006ANFS
CF5006ANF
–
20
40
50
–
150
SM5006ANAS, CF5006ANA
6.97
8.2
9.43
SM5006ANBS, CF5006ANB
4.76
5.6
6.44
SM5006ANCS, CF5006ANC
SM5006CNCS, CF5006CNC
4.16
4.9
5.64
SM5006ANDS, CF5006AND
SM5006ANES, CF5006ANE
SM5006ANFS, CF5006ANF
SM5006CNDS, CF5006CND
SM5006CNES, CF5006CNE
2.21
2.6
2.99
Measurement cct 4
Measurement cct 5
µA
mA
kΩ
kΩ
RG
Design value, determined by the Rf value
17
20
23
RD
Design value, determined by the Rf value
17
20
23
CG
Design value. A monitor pattern on a wafer is tested.
7.44
8
8.56
CD
Design value. A monitor pattern on a wafer is tested.
14.88
16
17.12
Ω
pF
SEIKO NPC CORPORATION —7
SM5006 series
5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Parameter
Symbol
Rating
Condition
min
typ
max
Unit
HIGH-level output
voltage
VOH
Q: Measurement cct 1, VDD = 4.5V, IOH = 16mA
4.0
4.2
–
V
LOW-level output voltage
VOL
Q: Measurement cct 2, VDD = 4.5V, IOL = 16mA
–
0.3
0.4
V
VOH = VDD
–
–
10
VOL = VSS
–
–
10
Output leakage current
IZ
Q: Measurement cct 2, INHN = LOW, VDD = 5.5V
HIGH-level input voltage
VIH
INHN
2.0
–
–
V
LOW-level input voltage
VIL
INHN
–
–
0.8
V
INHN = open,
Measurement cct 3,
load cct 1,
VDD = 4.5 to 5.5V,
CL = 50pF
Current consumption
IDD
INHN = open,
Measurement cct 3,
load cct 1,
VDD = 4.5 to 5.5V
INHN pull-up resistance
Feedback resistance
Built-in resistance
Built-in capacitance
RUP
Rf
f = 30MHz
SM5006ANAS
CF5006ANA
–
18
35
f = 40MHz
SM5006ANBS
CF5006ANB
–
20
40
f = 60MHz
CF5006ANC
–
30
60
f = 60MHz,
Ta = –20 to 80°C
SM5006ANCS
–
30
50
f = 70MHz
CF5006AND
CF5006BNC
–
40
80
f = 70MHz,
Ta = –20 to 80°C
SM5006ANDS
SM5006BNCS
–
40
70
f = 60MHz, CL = 15pF,
Ta = –15 to 75°C
CF5006CNC
–
28
50
f = 60MHz, CL = 15pF,
Ta = 0 to 70°C
SM5006CNCS
–
28
50
f = 70MHz, CL = 15pF,
Ta = –15 to 75°C
CF5006CND
CF5006DNC
–
35
65
f = 70MHz, CL = 15pF,
Ta = 0 to 70°C
SM5006CNDS
SM5006DNCS
–
35
65
f = 100MHz, CL = 15pF,
Ta = –20 to 80°C
CF5006CNE
CF5006DNE
–
45
80
f = 100MHz, CL = 15pF,
Ta = 0 to 70°C
SM5006CNES
SM5006DNES
–
45
80
f = 100MHz, CL = 30pF
CF5006ANE
–
50
100
f = 100MHz, CL = 15pF
SM5006ANES
–
45
90
f = 107MHz, CL = 30pF,
Ta = –20 to 80 °C
CF5006ANF
CF5006BNE
–
60
100
f = 107MHz, CL = 15pF,
Ta = –20 to 80°C
SM5006ANFS
SM5006BNES
–
50
90
50
–
150
SM5006ANAS, CF5006ANA
6.97
8.2
9.43
SM5006ANBS, CF5006ANB
4.76
5.6
6.44
SM5006ANCS, CF5006ANC
SM5006CNCS, CF5006CNC
4.16
4.9
5.64
SM5006ANDS, CF5006AND
SM5006ANES, CF5006ANE
SM5006ANFS, CF5006ANF
SM5006CNDS, CF5006CND
SM5006CNES, CF5006CNE
2.21
2.6
2.99
Measurement cct 4
Measurement cct 5
µA
mA
kΩ
kΩ
RG
Design value, determined by the Rf value
17
20
23
RD
Design value, determined by the Rf value
17
20
23
CG
Design value. A monitor pattern on a wafer is tested.
7.44
8
8.56
CD
Design value. A monitor pattern on a wafer is tested.
14.88
16
17.12
Ω
pF
SEIKO NPC CORPORATION —8
SM5006 series
5006×K series
VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Rating
Parameter
HIGH-level output voltage
LOW-level output voltage
Symbol
VOH
VOL
Condition
Q: Measurement cct 1,
VDD = 4.5V,
IOH = 16mA
Unit
min
typ
max
SM5006AKAS, CF5006AKA
SM5006AKBS, CF5006AKB
SM5006AKCS, CF5006AKC
SM5006CKDS, CF5006CKD
SM5006DKCS, CF5006DKC
3.9
4.2
–
SM5006AKDS, CF5006AKD
SM5006BKCS, CF5006BKC
4.0
4.2
–
–
0.3
0.4
VOH = VDD
–
–
10
VOL = VSS
–
–
10
Q: Measurement cct 2, VDD = 4.5V, IOL = 16mA
V
V
IZ
Q: Measurement cct 2, INHN = LOW,
VDD = 5.5V
HIGH-level input voltage
VIH
INHN
2.0
–
–
V
LOW-level input voltage
VIL
INHN
–
–
0.8
V
Output leakage current
Current consumption
INHN pull-up resistance
Feedback resistance
Built-in resistance
Built-in capacitance
IDD
RUP
Rf
INHN = open,
Measurement cct 3,
load cct 1,
VDD = 4.5 to 5.5V,
CL = 15pF
f = 30MHz
SM5006AKAS
CF5006AKA
–
16
32
f = 40MHz
SM5006AKBS
CF5006AKB
–
18
36
f = 60MHz,
Ta = –15 to 75°C
CF5006AKC
CF5006DKC
–
25
50
f = 60MHz,
Ta = 0 to 70°C
SM5006AKCS
SM5006DKCS
–
25
50
f = 70MHz,
Ta = –20 to 80°C
CF5006AKD
CF5006BKC
–
35
70
f = 70MHz,
Ta = –15 to 75°C
CF5006CKD
–
35
70
f = 70MHz,
Ta = 0 to 70°C
SM5006AKDS
SM5006BKCS
SM5006CKDS
–
35
70
50
–
150
SM5006AKAS, CF5006AKA
6.97
8.2
9.43
SM5006AKBS, CF5006AKB
4.76
5.6
6.44
SM5006AKCS, CF5006AKC
4.16
4.9
5.64
SM5006AKDS, CF5006AKD
SM5006CKDS, CF5006CKD
2.21
2.6
2.99
Measurement cct 4
Measurement cct 5
µA
RG
Design value, determined by the Rf value
17
20
23
RD
Design value, determined by the Rf value
17
20
23
CG
Design value. A monitor pattern on a wafer is tested.
7.44
8
8.56
CD
Design value. A monitor pattern on a wafer is tested.
14.88
16
17.12
mA
kΩ
kΩ
Ω
pF
SEIKO NPC CORPORATION —9
SM5006 series
5006AH series
VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Rating
Parameter
Symbol
Condition
Unit
min
typ
max
HIGH-level output voltage
VOH
Q: Measurement cct 1, VDD = 4.5V, IOH = 4mA
3.9
4.2
–
V
LOW-level output voltage
VOL
Q: Measurement cct 2, VDD = 4.5V, IOL = 4mA
–
0.3
0.5
V
VOH = VDD
–
–
10
VOL = VSS
–
–
10
IZ
Q: Measurement cct 2, INHN = LOW,
VDD = 5.5V
HIGH-level input voltage
VIH
INHN
2.0
–
–
V
LOW-level input voltage
VIL
INHN
–
–
0.8
V
Output leakage current
Current consumption
INHN pull-up resistance
Feedback resistance
Built-in resistance
Built-in capacitance
IDD
RUP
Rf
INHN = open,
Measurement cct 3,
load cct 1,
VDD = 4.5 to 5.5V,
CL = 15pF
µA
f = 30MHz
SM5006AHAS
CF5006AHA
–
15
30
f = 40MHz
SM5006AHBS
CF5006AHB
–
18
36
f = 60MHz,
Ta = –20 to 80°C
CF5006AHC
–
25
50
f = 60MHz,
Ta = –15 to 75°C
SM5006AHCS
–
25
50
f = 70MHz,
Ta = –20 to 80°C
CF5006AHD
–
32
65
f = 70MHz,
Ta = –15 to 75°C
SM5006AHDS
–
32
65
50
–
150
SM5006AHAS, CF5006AHA
6.97
8.2
9.43
SM5006AHBS, CF5006AHB
4.76
5.6
6.44
SM5006AHCS, CF5006AHC
4.16
4.9
5.64
SM5006AHDS, CF5006AHD
2.21
2.6
2.99
mA
Measurement cct 4
Measurement cct 5
kΩ
kΩ
RG
Design value, determined by the Rf value
17
20
23
RD
Design value, determined by the Rf value
17
20
23
CG
Design value. A monitor pattern on a wafer is tested.
7.44
8
8.56
CD
Design value. A monitor pattern on a wafer is tested.
14.88
16
17.12
Ω
pF
SEIKO NPC CORPORATION —10
SM5006 series
Switching Characteristics
5006×N series
3V operation: VDD = 2.7 to 3.6V, VSS = 0V, Ta = −20 to 80°C unless otherwise noted.
Parameter
Symbol
Condition
min
typ
max
–
3.5
7.0
Unit
Measurement cct 3,
load cct 1,
0.1VDD to 0.9VDD ,
CL = 15pF,
Ta = –10 to 70°C
SM5006ANAS, CF5006ANA
SM5006ANBS, CF5006ANB
SM5006CNCS, CF5006CNC
SM5006CNDS, CF5006CND
SM5006DNCS, CF5006DNC
tr2
Measurement cct 3,
load cct 1,
0.1VDD to 0.9VDD ,
CL = 15pF
SM5006ANCS, CF5006ANC
SM5006ANDS, CF5006AND
SM5006ANES, CF5006ANE
SM5006ANFS, CF5006ANF
SM5006BNCS, CF5006BNC
SM5006BNES, CF5006BNE
SM5006CNES, CF5006CNE
SM5006DNES, CF5006DNE
–
3.5
7.0
tf1
Measurement cct 3,
load cct 1,
0.9VDD to 0.1VDD ,
CL = 15pF,
Ta = –10 to 70°C
SM5006ANAS, CF5006ANA
SM5006ANBS, CF5006ANB
SM5006CNCS, CF5006CNC
SM5006CNDS, CF5006CND
SM5006DNCS, CF5006DNC
–
3.5
7.0
Measurement cct 3,
load cct 1,
0.9VDD to 0.1VDD ,
CL = 15pF
SM5006ANCS, CF5006ANC
SM5006ANDS, CF5006AND
SM5006ANES, CF5006ANE
SM5006ANFS, CF5006ANF
SM5006BNCS, CF5006BNC
SM5006BNES, CF5006BNE
SM5006CNES, CF5006CNE
SM5006DNES, CF5006DNE
–
3.5
7.0
Measurement cct 3,
load cct 1, Ta = 25°C,
VDD = 3.3V, CL = 15pF,
f = 30MHz
SM5006ANAS, CF5006ANA
SM5006ANBS, CF5006ANB
SM5006ANCS, CF5006ANC
SM5006CNCS, CF5006CNC
40
–
60
Measurement cct 3,
load cct 1, Ta = 25°C,
VDD = 3.3V, CL = 15pF,
f = 40MHz
SM5006CNDS, CF5006CND
SM5006DNCS, CF5006DNC
40
–
60
Measurement cct 3,
load cct 1, Ta = 25°C,
VDD = 3.3V, CL = 15pF,
f = 50MHz
SM5006ANDS, CF5006AND
SM5006BNCS, CF5006BNC
40
–
60
Measurement cct 3,
load cct 1, Ta = 25°C,
VDD = 3.3V, CL = 15pF,
f = 70MHz
SM5006ANES, CF5006ANE
SM5006ANFS, CF5006ANF
SM5006BNES, CF5006BNE
SM5006CNES, CF5006CNE
SM5006DNES, CF5006DNE
40
–
60
–
–
100
ns
–
–
100
ns
tr1
Output rise time
Output fall time
tf2
Output duty cycle*1
Rating
Duty
Output disable delay time
tPLZ
Output enable delay time
tPZL
ns
ns
%
Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF
*1. The duty cycle characteristic is checked the sample chips of each production lot.
SEIKO NPC CORPORATION —11
SM5006 series
5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Parameter
Symbol
tr1
tr2
Output rise time
tr3
tf1
tf2
Output fall time
tf3
Condition
Measurement cct 3,
load cct 1,
0.1VDD to 0.9VDD ,
CL = 15pF
Measurement cct 3,
load cct 1,
0.1VDD to 0.9VDD ,
CL = 30pF
Measurement cct 3,
load cct 1,
0.1VDD to 0.9VDD ,
CL = 50pF
Measurement cct 3,
load cct 1,
0.9VDD to 0.1VDD ,
CL = 15pF
Measurement cct 3,
load cct 1,
0.9VDD to 0.1VDD ,
CL = 30pF
Measurement cct 3,
load cct 1,
0.9VDD to 0.1VDD ,
CL = 50pF
Rating
min
typ
max
SM5006ANAS, CF5006ANA
SM5006ANBS, CF5006ANB
SM5006CNCS, CF5006CNC
SM5006CNDS, CF5006CND
SM5006DNCS, CF5006DNC
–
2.0
4.0
SM5006ANCS, CF5006ANC
SM5006ANDS, CF5006AND
SM5006BNCS, CF5006BNC
SM5006CNES, CF5006CNE
SM5006DNES, CF5006DNE
–
1.5
3.0
CF5006ANE
CF5006ANF
CF5006BNE
–
2.0
4.0
SM5006ANAS, CF5006ANA
SM5006ANBS, CF5006ANB
SM5006CNCS, CF5006CNC
SM5006CNDS, CF5006CND
SM5006DNCS, CF5006DNC
–
4.0
8.0
SM5006ANCS, CF5006ANC
SM5006ANDS, CF5006AND
SM5006BNCS, CF5006BNC
SM5006CNES, CF5006CNE
SM5006DNES, CF5006DNE
–
3.5
7.0
SM5006ANES, CF5006ANE
SM5006ANFS, CF5006ANF
SM5006BNES, CF5006BNE
–
3.0
6.0
SM5006ANAS, CF5006ANA
SM5006ANBS, CF5006ANB
SM5006CNCS, CF5006CNC
SM5006CNDS, CF5006CND
SM5006DNCS, CF5006DNC
–
2.0
4.0
SM5006ANCS, CF5006ANC
SM5006ANDS, CF5006AND
SM5006BNCS, CF5006BNC
SM5006CNES, CF5006CNE
SM5006DNES, CF5006DNE
–
1.5
3.0
CF5006ANE
CF5006ANF
CF5006BNE
–
2.0
4.0
SM5006ANAS, CF5006ANA
SM5006ANBS, CF5006ANB
SM5006CNCS, CF5006CNC
SM5006CNDS, CF5006CND
SM5006DNCS, CF5006DNC
–
4.0
8.0
SM5006ANCS, CF5006ANC
SM5006ANDS, CF5006AND
SM5006BNCS, CF5006BNC
SM5006CNES, CF5006CNE
SM5006DNES, CF5006DNE
–
3.5
7.0
SM5006ANES, CF5006ANE
SM5006ANFS, CF5006ANF
SM5006BNES, CF5006BNE
–
3.0
6.0
Unit
ns
ns
SEIKO NPC CORPORATION —12
SM5006 series
Parameter
Output duty cycle*1
Symbol
Duty
Output disable delay time
tPLZ
Output enable delay time
tPZL
Rating
Condition
Measurement cct 3,
load cct 1,
Ta = 25°C,
VDD = 5.0V
min
typ
max
Unit
f = 30MHz,
CL = 50pF
SM5006ANAS
CF5006ANA
45
–
55
f = 40MHz,
CL = 50pF
SM5006ANBS
CF5006ANB
45
–
55
f = 60MHz,
CL = 50pF
SM5006ANCS
CF5006ANC
45
–
55
f = 70MHz,
CL = 50pF
SM5006ANDS
CF5006AND
SM5006BNCS
CF5006BNC
45
–
55
f = 100MHz,
CL = 30pF
CF5006ANE
45
–
55
f = 100MHz,
CL = 15pF
SM5006ANES
45
–
55
f = 107MHz,
CL = 30pF
CF5006ANF
CF5006BNE
45
–
55
f = 107MHz,
CL = 15pF
SM5006ANFS
SM5006BNES
45
–
55
f = 50MHz,
CL = 50pF
SM5006CNCS
CF5006CNC
SM5006DNCS
CF5006DNC
45
–
55
f = 100MHz,
CL = 15pF
SM5006CNES
CF5006CNE
SM5006DNES
CF5006DNE
45
–
55
f = 60MHz,
CL = 15pF
SM5006CNCS
CF5006CNC
40
–
60
f = 70MHz,
CL = 15pF
SM5006CNDS
CF5006CND
SM5006DNCS
CF5006DNC
40
–
60
–
–
100
ns
–
–
100
ns
Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF
%
*1. The duty cycle characteristic is checked the sample chips of each production lot.
SEIKO NPC CORPORATION —13
SM5006 series
5006×K series
VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Parameter
Symbol
Rating
Condition
min
typ
max
Unit
Output rise time
tr
Measurement cct 3, load cct 1,
0.4V to 2.4V, VDD = 4.5 to 5.5V
CL = 15pF
–
2
4
CL = 50pF
–
–
7
Output fall time
tf
Measurement cct 3, load cct 1,
2.4V to 0.4V, VDD = 4.5 to 5.5V
CL = 15pF
–
2
4
CL = 50pF
–
–
7
f = 30MHz
SM5006AKAS
CF5006AKA
45
–
55
f = 40MHz
SM5006AKBS
CF5006AKB
45
–
55
f = 60MHz
SM5006AKCS
CF5006AKC
40
–
60
f = 70MHz
SM5006AKDS
CF5006AKD
SM5006BKCS
CF5006BKC
45
–
55
f = 50MHz
SM5006DKCS
CF5006DKC
45
–
55
f = 70MHz
SM5006CKDS
CF5006CKD
SM5006DKCS
CF5006DKC
40
–
60
–
–
100
ns
–
–
100
ns
Output duty cycle*1
Duty
Output disable delay time
tPLZ
Output enable delay time
tPZL
Measurement cct 3,
load cct 1, Ta = 25°C,
VDD = 5.0V, CL = 15pF
Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF
ns
ns
%
*1. The duty cycle characteristic is checked the sample chips of each production lot.
5006AH series
VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted.
Parameter
Output rise time
Output fall time
Output duty cycle*1
Symbol
tr1
tr2
tf1
tf2
Duty
Output disable delay time
tPLZ
Output enable delay time
tPZL
Rating
Condition
min
typ
max
Unit
Measurement cct 3, load cct 1,
0.1VDD to 0.9VDD
CL = 15pF
–
5.0
7.0
CL = 50pF
–
13
21
Measurement cct 3, load cct 1,
0.9VDD to 0.1VDD
CL = 15pF
–
5.0
7.0
CL = 50pF
–
13
21
f = 30MHz
SM5006AHAS
CF5006AHA
45
–
55
f = 40MHz
SM5006AHBS
CF5006AHB
45
–
55
f = 50MHz
SM5006AHCS
CF5006AHC
45
–
55
f = 60MHz,
Ta = –20 to 80°C
CF5006AHC
40
–
60
f = 60MHz,
Ta = –15 to 75°C
SM5006AHCS
40
–
60
f = 70MHz,
Ta = –20 to 80°C
CF5006AHD
40
–
60
f = 70MHz,
Ta = –15 to 75°C
SM5006AHDS
40
–
60
–
–
100
ns
–
–
100
ns
Measurement cct 3,
load cct 1, Ta = 25°C,
VDD = 5.0V, CL = 15pF
Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF
ns
ns
%
*1. The duty cycle characteristic is checked the sample chips of each production lot.
SEIKO NPC CORPORATION —14
SM5006 series
Current consumption and Output waveform with NPC’s standard crystal
Cb
L
Ca
R
f [MHz]
R [Ω]
L [mH]
Ca [fF]
Cb [pF]
30
18.62
16.24
1.733
5.337
40
20.53
11.34
1.396
3.989
50
22.17
7.40
1.370
4.105
70
25.42
4.18
1.254
5.170
100
16.60
3.56
0.726
5.394
107
35.83
2.98
0.732
2.265
FUNCTIONAL DESCRIPTION
Standby Function
When INHN goes LOW, the oscillator output on Q goes high impedance.
INHN
Q
Oscillator
HIGH (or open)
fO output frequency
Normal operation
LOW
High impedance
Normal operation
SEIKO NPC CORPORATION —15
SM5006 series
MEASUREMENT CIRCUITS
Measurement cct 1
Measurement cct 4
5.0V
VDD
C1
Signal
Generator
XT
VDD
Q
R2
Rfo
R1
XTN
RUP =
VDD
IPR
VSS
INHN
VSS
VOH
Q out monitor
VIH A
0V
IPR
3.5VP−P , 10MHz sine wave input signal (5V operation)
2.0VP−P , 10MHz sine wave input signal (3V operation)
C1 : 0.001µF
R1 : 50Ω
R2 : 250Ω (5006×N×/5V operation)
275Ω (5006×N×/3V operation)
245Ω (5006AKA, AKB, AKC, CKD, DKC)
250Ω (5006AKD, BKC)
975Ω (5006AH×)
Rfo : 2.7kΩ (5006B××, D××)
Measurement cct 2
Measurement cct 5
IOL, IZ
VDD
IZ
VDD
XT
A
Q
XT
Rf =
XTN
INHN VSS
V VOL
VDD
IRf
VSS
A
IRf
Measurement cct 3
IDD
IST
A
XT
Rfo
VDD
X'tal
Q
XTN
INHN
VSS
Rfo : 2.7kΩ (5006B××, D××)
SEIKO NPC CORPORATION —16
SM5006 series
Load cct 1
Load cct 2
Q output
400Ω
CL
Q output
(Including probe
capacitance)
CL
(Including probe
capacitance)
Switching Time Measurement Waveform
Output duty level (CMOS)
0.9VDD
Q output
0.9VDD
0.1VDD
0.1VDD
DUTY measurement
voltage (0.5V DD )
TW
tr
tf
Output duty level (TTL)
2.4V DD
Q output
2.4V DD
0.4V DD
0.4V DD
DUTY measurement
voltage (1.4V DD )
TW
tr
tf
Output duty cycle (CMOS)
DUTY measurement
voltage (0.5V DD)
Q output
TW
T
DUTY= TW/ T
100 (%)
Output duty cycle (TTL)
DUTY measurement
voltage (1.4V DD)
Q output
TW
T
DUTY= TW/ T
100 (%)
SEIKO NPC CORPORATION —17
SM5006 series
Output Enable/Disable Delay
INHN
VIH
VIL
tPLZ
tPZL
INHN input waveform tr = tf
10ns
Q output
SEIKO NPC CORPORATION —18
SM5006 series
Please pay your attention to the following points at time of using the products shown in this document.
The products shown in this document (hereinafter “Products”) are not intended to be used for the apparatus that exerts harmful influence on
human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such
use from SEIKO NPC CORPORATION (hereinafter “NPC”). Customers shall be solely responsible for, and indemnify and hold NPC free and
harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right
to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that
the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties.
Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document.
Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products,
and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or
modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in
compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested
appropriately take steps to obtain required permissions or approvals from appropriate government agencies.
SEIKO NPC CORPORATION
15-6, Nihombashi-kabutocho, Chuo-ku,
Tokyo 103-0026, Japan
Telephone: +81-3-6667-6601
Facsimile: +81-3-6667-6611
http://www.npc.co.jp/
Email: [email protected]
NC9713FE
2006.04
SEIKO NPC CORPORATION —19
Similar pages